Multi-Purpose Oscillating Tool Outil oscillant à usages multiples Herramienta oscilante multiuso

GMT15A

Operator’s ManualManuel d’utilisation Manual del Operario

888-552-8665TOLL FREEHELP LINE:

WEBSITE: www.genesispowertools.com

Eng

lish

Multi-Purpose Oscillating Tool Operator’s Manual GMT15A

MULTI-PURPOSE OSCILLATING TOOLOperator’s Manual

SPECIFICATIONS• Model:------------------------GMT15A• RatedPower:----------------- 120V~,60Hz,1.6A• No-LoadSpeed:-------------- 21,000/min(OPM)• NetWeight:------------------- 2.5Lbs

IncludesOscillatingTool,Hook&LoopSandingPad,AssortedSandpaper,RigidScraperBlade,1-3/16"(30mm)FlushCutSawBlade,HSSSegmentedSawBlade3-1/8",Wrench,AccessoryAdaptorandAccessoryStorageCase.

WARNING:To reduce the risk of injury, user must read and understand this operator’s manual before operating this tool. Save this Manual for future reference.

Toll-Free Help Line: 1-888-552-8665

WARNING: TheOperationofanypowertoolcanresult in foreignobjectsbeing thrown intoyoureyes,whichcanresult insevereeyedamage.Beforebeginningtooloperation,alwayswearsafetygogglesorsafetyglasseswith side shields and a full face shield when needed.We recommendWideVisionSafetyMaskforuseovereyeglassesorstandardsafetyglasseswithsideshields.AlwaysweareyeprotectionwhichismarkedtocomplywithANSIZ87.1.

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

GENERAL SAFETY RULES

WARNING:Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Leadfromlead-basedpaints.• Crystallinesilicafrombricksandcementandothermasonryproducts.• Arsenicandchromiumfromchemicallytreatedlumber.

Yourriskfromtheseexposuresvaries,dependingonhowoftenyoudothistypeofwork.Toreduceyourexposuretothesechemicals:workinawellventilatedarea,andworkwithapprovedsafetyequipment,suchasthosedustmasksthatarespeciallydesignedtofilteroutmicroscopicparticles.

WARNING:Read and understand all warnings, cautions and operating instructions before using this equipment. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WeARYOuR

FOReSIGHTISBeTTeRTHANNOSIGHT

SAFeTYGLASSeS

3

Eng

lish

WORK AREA SAFETY

• Keep your work area clean and well lit.Clutteredbenchesanddarkareasinviteaccidents.

• Do not operate power tools in explosive atmospheres,suchasinthepresenceofflammableliquids,gases,ordust.Powertoolscreatesparkswhichmayignitethedustorfumes.

• Keep bystanders, children, and visitors away while operating a power tool.Distractionscancauseyoutolosecontrol.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Nevermodifythepluginanyway.Donotuseanyadaptorplugsinanyearthed(grounded)powertools.Doubleinsulatedtoolsareequippedwithapolarizedplug(onebladeiswiderthantheother).Thisplugwillfitinapolarizedoutletonlyoneway.Iftheplugdoesnotfitfullyintheoutlet,reversetheplug.Ifitstilldoesnotfit,contactaqualifiedelectriciantoinstallapolarizedoutlet.Donotchangethepluginanyway.Doubleinsulationeliminatestheneedforthethreewiregroundedpowercordandgroundedpowersupplysystem.

• Do not expose power tools to rain or wet conditions. Waterenteringapowertoolwillincreasetheriskofelectricshock.

• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. Thereisanincreasedriskofelectricshockifyourbodyisgrounded.

• Do not abuse the cord. Neverusethecordforcarrying,pullingorunpluggingthepowertool.Keepcordawayfromheat,oil,sharpedgesormovingparts.Damagedcordsincreasetheriskofelectricshock.

• When operating a power tool outside, use an extension cord suitable for outdoor use. Thesecordsareratedforoutdooruseandreducetheriskofelectricshock.

• Do not use AC only rated tools with a DC power supply. Whilethetoolmayappeartowork.TheelectricalcomponentsoftheACratedtoolarelikelytofailandrateahazardtotheoperator.

PERSONAL SAFETY

• Stay alert, watchwhatyouaredoingandusecommonsensewhenoperatingapowertool.Donotusetoolwhiletiredorundertheinfluenceofdrugs,alcohol,ormedication.Amomentofinattentionwhileoperatingpowertoolsmayresultinseriouspersonalinjury.

• Use safety equipment. Alwaysweareyeprotection.Safetyequipmentsuchasdustmask,non-skidsafetyshoes,hardhat,orhearingprotectionforappropriateconditionswillreducepersonalinjuries.

• Dress properly. Donotwearlooseclothingorjewelry.Keepyourhair,clothingandglovesawayfrommovingparts.Looseclothes,jewelryorlonghaircanbecaughtinmovingparts.Airventsmaycovermovingpartsandshouldbeavoided.

• Avoid accidental starting. ensuretheswitchisintheoffpositionbeforepluggingin.Carryingpowertoolwithyourfingerontheswitchorplugginginpowertoolsthathavetheswitchoninvitesaccidents.

• Remove any adjusting keys or wrenches before turning the power tool on. Awrenchorkeythatisleftattachedtoarotatingpartofthetoolmayresultinpersonalinjury.

• Do not overreach. Maintainproperfootingandbalanceatalltimes.Lossofbalancecancauseaninjuryinanunexpectedsituation.

• If devices are provided for connection of dust extraction and collection facilities, ensure these are connected and properly used. useofthesedevicescanreducedustrelatedhazards.

• Do not use a ladder or unstable support. Stablefootingonasolidsurfaceenablesbettercontrolofthetoolinunexpectedsituations.

• Keep tool handles dry, clean and free from oil and grease. Slipperyhandlescannotsafelycontrolthetool.

TOOL USE AND CARE

• Secure the workpiece. useclamporotherpracticalwaytoholdtheworkpiecetoastableplatform.Holdingtheworkpiecebyhandoragainstyourbodyisunstableandmayleadtolossofcontrol.

Eng

lish

Multi-Purpose Oscillating Tool Operator’s Manual GMT15A

• Do not force the power tool. Thetoolwillperformthejobbetterandsaferatthefeedrateforwhichitisdesigned.Forcingthetoolcouldpossiblydamagethetoolandmayresultinpersonalinjury.

• Use the correct power tool for the job. Don’tforcethetoolorattachmenttodoajobforwhichitisnotdesigned.

• Do not use tool if switch does not turn it on or off. Anytoolthatcannotbecontrolledwiththeswitchisdangerousandmustberepairedorreplacedbyanauthorizedservicecenter.

• Turn power tool off, and disconnect the plug fromthepowersourceand/orbatterypackfromthepowertoolbeforemakinganyadjustments,changingtheaccessories,orstoringthetools. Suchpreventivesafetymeasuresreducetheriskofanaccidentalstartupwhichmaycausepersonalinjury.

• Store idle tool out of reach of children and other inexperienced persons. Itisdangerousinthehandofuntrainedusers.

• Maintain power tools with care. Checkforproperalignmentandbindingofmovingparts,componentbreaks,andanyotherconditionsthatmayaffectthetool’soperation.Aguardoranyotherpartthatisdamagedmustbeproperlyrepairedorreplacedbyanauthorizedservicecentertoavoidriskofpersonalinjury.

• Use recommended accessories. usingaccessoriesandattachmentsnotrecommendedbythemanufacturerorintendedforuseonthistypetoolmaycausedamagetothetoolorresultinpersonalinjurytotheuser.Consulttheoperator’smanualforrecommendedaccessories.

• Keep cutting tools sharp and clean. Properlymaintainedcuttingtoolswithsharpcuttingedgesarelesslikelytobindandareeasiertocontrol.

• Feed the workpiece in the correct direction and speed. Feedtheworkpieceintoablade,cutter,orabrasivesurfaceagainstthedirectionofthecuttingtool’sdirectionofrotationonly.Incorrectlyfeedingtheworkpieceinthesamedirectionmaycausetheworkpiecetobethrownoutathighspeed.

• Never leave the tool running unattended, turn the power off. Donotleavethetooluntilitcomestoacompletestop.

WARNING: USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST AND ASBESTOS. Direct particles away from face and body. Always operate tool in a well-ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for dust exposure, and wash exposed areas with soap and water.

SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. Thiswillensurethatthesafetyofthepowertoolismaintained.

• Service your power tool periodically. Whencleaningatool,becarefulnottodisassembleanyportionofthetoolsinceinternalwiresmaybemisplacedorpinched.

SAVE THESE INSTRUCTIONS

5

Eng

lish

EXTENSION CORDSGrounded tools require a three wire extension cord.Doubleinsulatedtoolscanuseeitheratwoorthreewireextensioncord.Asthedistancefromthepowersupplyoutletincreases,youmustuseaheaviergaugeextensioncord.usingextensioncordswithinadequatelysizedwirecausesaseriousdropinvoltage,resultinginlossofpowerandpossibletooldamage.Refertothetableshownbelowtodeterminetherequiredminimumwiresize.Thesmallerthegaugenumberofthewire,thegreaterthecapacityofthecord.Forexample:a14-gaugecordcancarryahighercurrentthana16-gaugecord.Whenusingmorethanoneextensioncordtomakeupthetotallength,besureeachcordcontainsatleasttheminimumwiresizerequired.Ifyouareusingoneextensioncordformorethanonetool,addthenameplateamperesandusethesumtodeterminetherequiredminimumwiresize.

Guidelines for Using Extension Cords• Ifyouareusinganextensioncordoutdoors,besureitismarkedwiththesuffix“W-A”(“W”inCanada)to

indicatethatitisacceptableforoutdooruse.• Besureyourextensioncordisproperlywiredandingoodelectricalcondition.Alwaysreplaceadamaged

extensioncordorhaveitrepairedbyaqualifiedpersonbeforeusingit.• Protectyourextensioncordsfromsharpobjects,excessiveheat,anddamporwetareas.

SPECIFIC SAFETY RULES FOR MULTI-PURPOSE OSCILLATING TOOLS

WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT (GAINED FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT SAFETY RULES. If you use this tool unsafe or incorrectly, you can suffer serious personal injury!

WARNING:Hold tool by insulated gripping surfaces when performing an operation where cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator!

• Always wear safety glasses or goggles. Normalprescriptioneyeorsunglassesarenotsafetyglasses.

• Hold the Oscillating Tool by its insulated gripping surfacestoavoidelectricalshockfromunseen“live”wires.

• Always hold the tool firmly. DOnotleavethetoolrunningunlesshandheld.

• Check your work area for proper clearances before cutting.Thiswillavoidcuttingintoyourworkbench,thefloor,etc.

• DO not cut nails or screws unlessyouareusingabladespecificallydesignedforthispurpose.Inspectyourmaterialbeforecutting.

• Before switching on the tool,besurethebladeisnotcontactingtheworkpiece.

• Do not use tool if switch does not turn it on or off.Anytoolwhichcannotbecontrolledbytheswitchisdangerousandmustberepaired.

• Wear cushioned protective gloves to minimize the vibration.excessivevibrationmaycausepersonalinjury.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate Amperes

(At Full Load)

Extension Cord Length

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 200 Feet

0–2.0 18 18 18 18 16 16

2.1–3.4 18 18 18 16 14 14

3.5–5.0 18 18 16 14 12 12

5.1–7.0 18 16 14 12 12 10

7.1–12.0 18 14 12 10 8 8

12.1–16.0 14 12 10 10 8 6

16.1–20.0 12 10 8 8 6 6

Eng

lish

Multi-Purpose Oscillating Tool Operator’s Manual GMT15A

• Do not wet-sand with this tool.Waterormoistureenteringthemotorhousingcancauseelectricshockandseriouspersonalinjury.

• Always be sure that the tool is switched off andunpluggedbeforeadjusting,addingaccessories,orcheckingafunctiononthetool.

WARNING: Read and understand all warnings, cautions and operating instructions before using this equipment. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

KNOWING YOUR OSCILLATING TOOL

1.ON/OFFSwitch2.CastAluminumGearHead3.OscillatingSpindleandBladeholder4.FlushCuttingBlade1-3/16”5.HSSSegmentedSawBlade3-1/8"

6.RigidScraperblade7.Hook&LoopSandingPad8.Sandpaper9.AccessoryAdaptor10.StorageBox

FIG 1

5

2

45

9

8

7

3

1

6

10

7

Eng

lish

UNPACKING AND CONTENTSIMPORTANT:Due to modern mass production techniques, it is unlikely the tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.

CONTENTS IN PACKAGE

Description Q'ty Description Q'ty

ASSEMBLY AND ADJUSTMENTS

WARNING: Always be sure that the tool is switched off and unplugged before adjusting, adding accessories, or checking a function on the tool.

To Install the Accessories (FIG 2)

YourtoolcomeswithasetofGeNeSIS™universalQuickFitaccessorieswhichcanbeinstalledwithoutcompletelyremovingthecapscrewandthebladewasher.

1. Loosenthecapscrew(a)usingAllenwrenchprovided.2. Slidetheopen-endoftheaccessoryintothegapbetweenthebladewasher(d)andtheshaftflange(b).

Placetheaccessoryovertheshaftflange(b).Theshaftflangeofthistoolcomeswitha4-pindesign.Makesuretheholesontheaccessoryproperlyengage3ofthose4pinsandtheaccessoryisflushagainsttheshaftflange.

3. Makesuretheconcavesideofthelargebladewasherisfacingtheaccessory.TightenthecapscrewsecurelyusingAllenwrench(c)provided.(SeeFIG2)

a

c

b

d

FIG 2

Oscillating Tool 11-3/16” Flush Cutting Saw Blade 13-1/8" HSS Segmented Saw Blade 1Rigid Scraper Blade 1Hook & Loop Sanding Pad 1Sandpapers 3

Allen Wrench 1Cap Screw and Washer 1Accessory Adaptor 1Storage Case 1Operator’s Manual 1

Eng

lish

Multi-Purpose Oscillating Tool Operator’s Manual GMT15A

NOTE:Some accessories, such as a saw blade, may be mounted either straight on the tool, or at an angle to enhance usability. Always make sure 3 of the 4 pins are engaged as described in step 2 above.

NOTE:For maximum sandpaper life, rotate the pad or sandpaper 120 degrees when tip of sandpaper becomes worn.

WARNING: DO NOT tighten the cap screw unless the accessory is properly seated on the shaft flange.

To Remove Accessories From the Tool, loosenthecapscrewandpulltheaccessoryoffthetool.

ACCESSORY ADAPTOR (FIG 3)

Auniversalaccessoryadaptor is included toallowusewithotherbrands’accessories.(Fein®,Bosch®,Dremel®,andRockwell®).SeeFIG3forhowtousethatadapor.

NOTE: Fein is a registered trademark of C. &e Fein GmbH. Bosch isa registered trademark of Robert Bosch GmbH. Dremel is a registeredtrademarkofCredoTechnologyCorp.RockwellisaregisteredtrademarkofPositecGroupLimited.

OPERATION

WARNING: To reduce the risk of serious personal injuries, read and follow all important safety warning and instructions before using this tool.

WARNING: Always be sure the tool is disconnected from the power source before making any adjustments or setting up prior to cutting. Failure to disconnect or unplug the tool may cause accidental starting, resulting in serious personal injury.

NOTE: Always Check that the power supply corresponds to the voltage on the ratings plate.

STARTING AND STOPPING THE OSCILLATING TOOL (FIG 4)

To Start the Oscillating Tool,slidetheON/OFFswitchforwardtoONposition.To Stop the Oscillating tool,slidetheON/OFFswitchbackwardtoOFFposition.

APPLICATIONSNOTE:Recommended oscillating tool accessories for this tool are the GENESIS™ oscillating tool accessories. Please refer to "Genesis Oscillating Tool Accessory Reference Guide" Sheet enclosed for details.

Thismulti-purposeoscillatingtoolisintendedforcuttingandsandingwood,plastic,plasterandnon-ferrousmetals.Itisespeciallysuitableforcuttingintightspacesandforflushcutting.Followingareafewtypicaluses.

CUTTING (FIG 5,6,7)

useaflushcuttingsawblade(or“e-cutblade”)formakingprecisecuts in tight areas, close to edges, plunge or flush to a surface.It is importantnottoforcethetoolduringtheflushcutting. Ifyouareexperiencingastrongvibration inyourhandduringthecut, itindicatestoomuchpressureonthetool.Backoffonthepressureandletthespeedoftooldothework.SeeFiG5,6fortypicalusesforflushcuttingsawblade.

ACCESSORY ADAPTOR

FIG 3

ONOFF

FIG 4

FIG 5

9

Eng

lish

NOTE: It is suggested that you have a piece of scrap material supporting the blade when making a flush cut. If you need to rest the blade on a delicate surface, you need to use cardboard or masking tape to protect the surface.

usethesegmentedsawbladeformakingcontinuousprecisecutsin wood, plaster or drywall material. Applications include cuttingopeningsforelectricalboxes,repairingflooring,cuttingflooringforventing,andmore. SeeFIG7 forhow touseof thesegmentedsawblade.

SANDING (FIG 8)

Withsandingaccessories,thistoolisadetailsander.Itissuitablefordrysandingofwood,plastic,andmetalsurfaces,especiallyincorners,edgesandhardtoreachareas.SeeFIG8.

Tips: 1. Workwiththecompletesurfaceofthesandpaper,notonlywith

thetip.2. Sandwithcontinuousmotionandlightpressure.Donotapply

excessivepressure.Lettooldothework.3. Alwayssecuresmallworkpieces.4. Selectsuitableabrasivepaperforbestresults.

SCRAPING (FIG 9)

Scraperbladesaresuitableforremovingvinyl,varnish,paintlayers,carpeting,caulkandotheradhesives.usearigidscraperbladetoremovehardermaterials,suchasvinylflooring,carpetingandtileadhesivesinalargearea.useaflexiblescraperblade(notincluded)toremovesoftermaterialsuchascaulk.

Tips: 1. When removing strong, tacky adhesive, grease the scraper

bladesurfacetoreducegummingup.2. Beginwithlightpressure.Theoscillatingmotionofaccessory

only occurs when pressure is applied to the material to beremoved.

3. Ifyouare removingcaulk fromadelicatesurface,suchasabathtubortilebacksplash,werecommendtapingtoprotectthesurfacethatthebladewillreston.

GROUT REMOVAL (FIG 10)

use a grout removal blade (not included) to remove damaged orcrackedgrout,orinordertoreplaceadamagedorbrokentile.Toremovethegrout,useabackandforthmotion,makingseveralpassesalongthegroutline.Becarefulnottoapplytoomuchsidepressureonthegroutblade.SeeFIG10.

ACCESSORIESRecommended oscillating tool accessories for this tool are the GENESIS™ oscillating tool accessories. Please refer to "Genesis Oscillating Tool Accessory Reference Guide" sheet enclosed for details.

FIG 6

FIG 7

FIG 8

FIG 9

FIG 10

Eng

lish

Multi-Purpose Oscillating Tool Operator’s Manual GMT15A

MAINTENANCECLEANING

Avoidusingsolventswhencleaningplasticparts.Mostplasticsaresusceptibletodamagefromvarioustypesofcommercialsolventsandmaybedamagedbytheiruse.usecleanclothstoremovedirt,dust,oil,grease,etc.

WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

electrictoolsusedonfiberglassmaterial,wallboard,spacklingcompounds,orplasteraresubjecttoacceleratedwearandpossibleprematurefailurebecausethefiberglasschipsandgrindingsarehighlyabrasivetobearings,brushes,commutators,etc.Consequently,wedonotrecommendedusingthistoolforextendedworkonthesetypesofmaterials.However,ifyoudoworkwithanyofthesematerials,itisextremelyimportanttocleanthetoolusingcompressedair.

LUBRICATION

Thistoolispermanentlylubricatedatthefactoryandrequiresnoadditionallubrication.

TWO-YEAR WARRANTYThisproductiswarrantedfreefromdefectsinmaterialandworkmanshipfor2yearsafterdateofpurchase.Thislimitedwarrantydoesnotcovernormalwearandtearordamagefromneglectoraccident.Theoriginalpurchaseriscoveredbythiswarrantyanditisnottransferable.Priortoreturningyourtooltostorelocationofpurchase,pleasecallourToll-FreeHelpLineforpossiblesolutions.

THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES. ACCESSORIES INCLUDED IN THIS KIT ARE NOT COVERED BY THE 2 YEAR WARRANTY.

TOLL-FREE HELP LINEForquestionsaboutthisoranyotherGeNeSIS™Product,pleasecallToll-Free:888-552-8665.

Orvisitourwebsite:www.genesispowertools.com

©Richpower Industries, Inc. All Rights reserved

RichpowerIndustries,Inc.

736HamptonRoad

Williamston,SC29697

PrintedinChina,onrecycledpaper

Richpower Industries, Inc.736 Hampton Road

Williamston, SC USAwww.genesispowertools.com

2013.08, V03