multi-stage electric deep well turbine and · pdf fileassembly incorporating non-reverse...
TRANSCRIPT
As Tyco policy is one of constant improvement, we reserve the right to make specification changes without notice and without incurring liability.
A.B.N. 83 000 922 690A division of Flow Control Pacific Pty Ltd
Ph: 131 786e-mail: [email protected]
web: www.southcross.com.au
MULTI-STAGE ELECTRIC
SUBMERSIBLE PUMPS
Features● Suit Bores from 150mm ● Heads to 600m ●
● Heavy Duty ● High Efficiency ● Australian Made ●● Outputs to 500 litres / sec. ●
ApplicationsDesigned for raising underground water supplies for…
—Irrigation —Industry —Community ——Domestic & Stock Watering —
Plus …—In-Line Pressure Boosting —
—Mine Dewatering—Waste Water —
DEEP WELL TURBINE AND
SUBMERSIBLE PUMPS
Everflow Direct Coupled Electric Submersible Pumps use the same high quality, highefficiency pumping elements as the line-shaft turbine units and are designed for usein boreholes, riverbanks, in-line pressure boosting applications and dewatering. StandardEverflow Submersible Pumps are suitable for 150mm and larger diameter boreholesand are capable of outputs to 100 litres per second and heads to 230 metres. Higherperformance units (covered by grey area of selection guide) are available on a made toorder basis. For pumps outside the performances shown contact Everflow Pumps.
Everflow Axial Flow Propeller pumpsare available in sizes from 150 to1000mm diameter with flows from 50to 5000 litres per sec. and heads to 25m.Call Everflow Pumps for full details.
250RH
250RM
200FHH200FHM
180RH
150RH
5 7 10 20 30 40 50 100 200 300
500
450
400
350
300
250
200
150
100
50
0
CAPACITY IN LITRES PER SECOND
TO
TAL
HE
AD
— M
ET
RE
S
MADE TOORDER
250FHM
250FHH
150RH
125LBH
250 RH
200 FHH
250 RM200 FH
M
200 CH
200 CM
180 RH
180 RM
MADE TOORDER
MADE TOORDER
150RXL
150RL
150RM
250FHM
250FHH
Distributed by…
Form 2785A Dec 2006
Individual performance curvesavailable on request
CONSTRUCTION FEATURESELECTRIC MOTOR DRIVES:Use standard solid shaft flange mounted electric motors fitted to heavy duty thrustassembly incorporating non-reverse ratchet, heavy duty grease lubricated thrustbearing and flexible shaft coupling.
RIGHT ANGLE GEAR DRIVES:Used for P.T.O. shaft diesel or petrol engine powered pumping applications andare available in a range of speed ratios and power ratings. Gearboxes are flangemounted on the thrust assembly.
DISCHARGE HEADS:Incorporating flanged outlet connection, water lubricated shaft packing gland andmachined spigotted mounting flange for thrust assembly mounting.
COLUMN AND SHAFTING:Column pipe is mild steel with either screwed or flanged connections in 1.5 or 3metre sections depending on pump running speeds and bearing spacingrequirements. Stainless steel drive shaft is supplied in 1.5 or 3 metre lengths withstainless steel couplings.
SHAFT BEARINGS:Water lubricated spiral grooved neoprene rubber shaft bearings are supported byrigid cast bronze bearing spiders fitted at each column pipe coupling givingminimum spacings of either 1.5 or 3 metres over the entire drive shaft.
PUMP STAGE CASINGS:Cast iron construction (option of cast bronze) incorporating diffuser vanes andrigid shaft support bearings. These tandem bronze and neoprene rubber bearingscombine to give accurate shaft support and abrasion resistance.
IMPELLERS:High efficiency cast bronze impellers are hydraulically and statically balanced forvibration free operation. Tapered stainless steel collets guarantee positive lockingof impellers to shaft.
DEEP WELL MULTI-STAGELINE-SHAFT TURBINE PUMPS
INLET STRAINERS:Choice of conical or basket type
inlet strainers are available inheavy galvanised mild steel or
stainless steel to suit installationtype and water quality.
Everflow Turbine Pumps use a series ofpump bowls and impellers (depending onhead requirements) which are shaft drivenfrom ground level by a choice of verticalshaft electric motor or right angle gear drivehead powered by diesel or petrol engine.Water is delivered to ground level via heavyduty column pipe connecting the pump todischarge head.Available in a wide range of sizes andconstruction options these Australian MadeEverflow Turbine Pumps provide thequality, performance and durability forreliable water supplies across a wide rangeof applications.
1 YEARWARRANTY
Everflow Turbine Pumps aremanufactured from premiumquality materials and precisionmanufacturing methods forguaranteed re l iab i l i ty andongoing performance.
PUMP SELECTIONGUIDE
Pumping and head capacities for thestandard range of Everflow TurbinePumps, in sizes to suit boreholes from150 mm diameter and upwards, areshown in colour at right, and coverpump performance for single to tenstage pump elements.
Higher performance units (covered bygrey area of selection guide) areavailable on a made to order basis. Forpumps outside the performancesshown contact Everflow Pumps.
300FHM300FHXM
250RH
250RM
250FHH250FHM
200FHH200FHM180RH
150RH
250RH250RM
250FHH250FH
5 7 10 20 30 40 50 100 200 300
500
450
400
350
300
250
200
150
100
50
0
CAPACITY IN LITRES PER SECOND
TOTA
L H
EAD
— M
ETR
ES
MADE TOORDER
250FHM
250FHH
150RH
125LBH
250 RH
200 FHH
250 RM200 FH
M
200 CH
200 CM
180 RH
180 RM
MADE TOORDER
MADE TOORDER
150RXL150RL
150RM
10 20 30 40 50 100 200 300 400 500
250
200
150
100
50
0
CAPACITY IN LITRES PER SECOND
TOTA
L H
EAD
— M
ETR
ES
1450 RPM
450HH
300RH
250RM
250RH
300FHM
300FHXM250FHH
250FHM
300FHH
400KHL
350FHM
350FHH
400FHH
400KHH
MADE TO ORDER
MADE TOORDER
2950 RPM