3/4"MAX

RAIL-LOCK™ 2"

SHADOW BOX DESIGN WITH ALTERNATING PICKETS RECOMMENDED FOR HIGH WIND AREAS

A1/8" GAP

BETWEEN POSTAND PICKETS

DETAIL A

OFFSET FASTENERS TYP

12"TYP.

TERRAPOST

TERRARAIL

COMPOSITE FASTENER

TERRADECK(TOP CAP)

24"MIN

73"MAX

ADDITIONAL INFORMATIONCOLOR AND WOOD GRAIN MAY VARY AMONG BOARDS.1.TERRA PICKET MAY "DEFLECT" DEPENDING UPON WEATHER AND 2.ENVIRONMENTAL CONDITIONS.INSTALL TERRA BALUSTERS AT THE BOTTOM OF PICKETS IF 3.UNACCEPTABLE LEVEL OF DEFLECTION OCCURS.ALWAYS CONSULT LOCAL AND REGIONAL BUILDING CODES.4.

6' PICTURE FRAME FENCE INSTALLATION INSTUCTIONSBEFORE YOU BEGIN

VERIFY LOCATION OF UNDERGROUND UTILITIES 1.BEFORE YOU BEGIN.LOCATE PROPERTY LINES.2.CONSULT LOCAL AND REGIONAL BUILDING CODES 3.BEFORE YOU BEGIN.ALWAYS WEAR APPROPIATE SAFETY EQUIPMENT.4.STANDARD WOODWORKING TOOLS MAY BE USED 5.FOR INSTALLATION.

POST INSTALLATIONDIG 12" DIAMETER HOLES 24" TO 36" DEEP 1.DEPENDING ON LOCAL BUILDING CODES.ADD 2" OF GRAVEL TO BOTTOM OF HOLES.2.SET POSTS IN 24" MINIMUM OF CONCRETE.3.BEFORE CONCRETE SETS, PLUMB AND LEVEL POSTS 4.MAKING SURE TO USE A STRING-LINE TO MAINTAIN ALIGNMENT.ALLOW CONCRETE TO PROPERLY SET BEFORE 5.PROCEEDING TO NEXT STEP.

RAILING INSTALLATONINSTALL RAIL-LOCKS™ IN RAILS AS SHOWN.1.DRILL 17/32" DIA HOLE IN RAIL 1-1/8" DEEP AS SHOWN.2.INSERT RAIL-LOCK™ INTO HOLE FLAT SIDE DOWN.3.COMPRESS RAIL-LOCK AND SLIDE RAIL INTO PRE-ROUTED HOLE IN 4.POST.RAIL-LOCK™ WILL EXPAND TO KEEP RAIL FROM FALLING OUT ONCE 5.RAIL IS INSTALLED INTO POST.

NOTE: LEAVE 2" GAP BETWEEN RAILS ENDS TOALLOW FOR EXPANSION.

PICKET INSTALLATIONATTACH PICKETS TO RAILS USING RECOMMENDED COMPOSITE FASTENERS.1.

NOTE: IT IS RECOMMENDED TO OFFSET FASTENERS ON EACH PICKET AS SHOWN IN DETAIL A.

BEGIN BY ATTACHING PICKETS NEXT TO POSTS FIRST. BE SURE TO LEAVE A 1/8" GAP 2.BETWEEN THE POST AND THE PICKET.CONTINUE BY INSTALLING PICKETS, EQUALLY SPACED IN THE AREA REMAINING.3.

NOTE: PICKETS MAY BE INSTALLED USING A NAIL GUN WITH DEPTH SET CAPABILITIES AND APPROPIATE FASTENERS.

TOP CAP INSTALLATONINSTALL TOP CAP USING TERRADECK PREMIUM BOARD.1.ATTACH TOP CAP USING RECOMMENDED COMPOSITE FASTENERS. 2.FASTENERS SHOULD BE POSITION AS TO JOIN THE TOP CAP AND RAIL TOGETHER SPACED 12" APART.

NOTE: IT IS RECOMMENDED TO LEAVE A 3/16" GAP BETWEEN TOP CAP BOARDS ALLOW FOR EXPANSION.

1302 Industrial Park Ave.Torrington, Wyoming 82240

(307) 532-9942

REMOVING FOOT PRINTS FROM OUR WORLD

WWW.NATURESCOMPOSITES.COMAUGUST 2011

3/4"MAX

RAIL-LOCK™ 2"

SHADOW BOX DESIGN WITH ALTERNATING PICKETS RECOMMENDED FOR HIGH WIND AREAS

A1/8" GAP

BETWEEN POSTAND PICKETS

DETAIL A

OFFSET FASTENERS TYP

12"TYP.

TERRAPOST

TERRARAIL

COMPOSITE FASTENER

TERRADECK(TOP CAP)

24"MIN

73"MAX

ADDITIONAL INFORMATIONCOLOR AND WOOD GRAIN MAY VARY AMONG BOARDS.1.TERRA PICKET MAY "DEFLECT" DEPENDING UPON WEATHER AND 2.ENVIRONMENTAL CONDITIONS.INSTALL TERRA BALUSTERS AT THE BOTTOM OF PICKETS IF 3.UNACCEPTABLE LEVEL OF DEFLECTION OCCURS.ALWAYS CONSULT LOCAL AND REGIONAL BUILDING CODES.4.

6' PICTURE FRAME FENCE INSTALLATION INSTUCTIONSBEFORE YOU BEGIN

VERIFY LOCATION OF UNDERGROUND UTILITIES 1.BEFORE YOU BEGIN.LOCATE PROPERTY LINES.2.CONSULT LOCAL AND REGIONAL BUILDING CODES 3.BEFORE YOU BEGIN.ALWAYS WEAR APPROPIATE SAFETY EQUIPMENT.4.STANDARD WOODWORKING TOOLS MAY BE USED 5.FOR INSTALLATION.

POST INSTALLATIONDIG 12" DIAMETER HOLES 24" TO 36" DEEP 1.DEPENDING ON LOCAL BUILDING CODES.ADD 2" OF GRAVEL TO BOTTOM OF HOLES.2.SET POSTS IN 24" MINIMUM OF CONCRETE.3.BEFORE CONCRETE SETS, PLUMB AND LEVEL POSTS 4.MAKING SURE TO USE A STRING-LINE TO MAINTAIN ALIGNMENT.ALLOW CONCRETE TO PROPERLY SET BEFORE 5.PROCEEDING TO NEXT STEP.

RAILING INSTALLATONINSTALL RAIL-LOCKS™ IN RAILS AS SHOWN.1.DRILL 17/32" DIA HOLE IN RAIL 1-1/8" DEEP AS SHOWN.2.INSERT RAIL-LOCK™ INTO HOLE FLAT SIDE DOWN.3.COMPRESS RAIL-LOCK AND SLIDE RAIL INTO PRE-ROUTED HOLE IN 4.POST.RAIL-LOCK™ WILL EXPAND TO KEEP RAIL FROM FALLING OUT ONCE 5.RAIL IS INSTALLED INTO POST.

NOTE: LEAVE 2" GAP BETWEEN RAILS ENDS TOALLOW FOR EXPANSION.

PICKET INSTALLATIONATTACH PICKETS TO RAILS USING RECOMMENDED COMPOSITE FASTENERS.1.

NOTE: IT IS RECOMMENDED TO OFFSET FASTENERS ON EACH PICKET AS SHOWN IN DETAIL A.

BEGIN BY ATTACHING PICKETS NEXT TO POSTS FIRST. BE SURE TO LEAVE A 1/8" GAP 2.BETWEEN THE POST AND THE PICKET.CONTINUE BY INSTALLING PICKETS, EQUALLY SPACED IN THE AREA REMAINING.3.

NOTE: PICKETS MAY BE INSTALLED USING A NAIL GUN WITH DEPTH SET CAPABILITIES AND APPROPIATE FASTENERS.

TOP CAP INSTALLATONINSTALL TOP CAP USING TERRADECK PREMIUM BOARD.1.ATTACH TOP CAP USING RECOMMENDED COMPOSITE FASTENERS. 2.FASTENERS SHOULD BE POSITION AS TO JOIN THE TOP CAP AND RAIL TOGETHER SPACED 12" APART.

NOTE: IT IS RECOMMENDED TO LEAVE A 3/16" GAP BETWEEN TOP CAP BOARDS ALLOW FOR EXPANSION.

1302 Industrial Park Ave.Torrington, Wyoming 82240

(307) 532-9942

REMOVING FOOT PRINTS FROM OUR WORLD

WWW.NATURESCOMPOSITES.COMAUGUST 2011

2.0

12.0TYP.

83

6

4

7

2

1

5CONCRETEIN WELLCOMPACTED SOIL

2

NOTESPOST CAPS SHALL BE ATTACHED TO POST BY SLIP FIT OVER POST. FOR ADDITIONAL HOLDING 1.STRENGTH, CAPS CAN BE ATTACHED WITH THE ADDITION OF EITHER CONSTRUCTION ADHESIVE OR BY SECURING IN PLACE BY PLACING A SMALL SCREW THROUGH THE SIDE OF POST CAP INTO THE POST. IT IS RECOMMENDED TO PRE-DRILL A SMALL PILOT HOLE THROUGH THE POST CAP BEFORE INSTALLING SCREW.SHOWN RECOMMENDED FOOTER. FOR STRUCTURAL LOADS , FOOTINGS SHALL BE DESIGNED BY 2.OTHER IN ACCORDANCE WITH LOCAL CODES. IN CASES WHERE DESIGN REQUIRES DEEPER BURIAL DEPTH OF POST THE LENGTH OF THE POST SHALL BE INCREASED ACCORDINGLY.

REVISIONSREV. DESCRIPTION DATE APPROVED

- INITIAL RELEASE 07/17/2015 JTM

ITEM NO. PART NO. DESCRIPTION QTY.BILL OF MATERIALS

8 - SCREW, #8 x 3/4" TRUSS HEAD 4

7 - SCREW, WOOD COMPOSITE #8 X 2 1/2" 12

6 - SCREW, WOOD COMPOSITE #8 X 1 1/4" 65

5 - CONCRETE BLOCK, 12" X 12" X 2" 1

4 300300-068 FENCE BOARD, 5 1/8" X 3/8" 13

3 PC750 POST CAP, 5 X 5 2

2 300600-070 BALUSTER, 1 1/4" X 1 1/4" 3

1 200755-096 HOLLOW POST, 5" X 5" X 96" 2

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFNATURES COMPOSITES, LLC. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFNATURES COMPOSITES, LLC. IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONAL: 1/16"ANGULAR: MACH 1 BEND 5TWO PLACE DECIMAL : .010THREE PLACE DECIMAL: .005

INTERPRET GEOMETRICTOLERANCING PER:

MATERIAL

FINISH

AS SPECIFIED

-

DRAWN

ENG APPR.

COMMENTS:

DATE

TITLE:

SIZE

BDWG. NO. REV

UNLESS OTHERWISE SPECIFIED:

-

J.T. MITCHELL 07/17/2015

07/16/2015

SHEET 1 OF 2

100005DO NOT SCALE DRAWING

HORIZONTAL BASKET WEAVE

J.T. MITCHELL

NAME

FENCE ASSEMBLY6 FT TALL X 6 FT WIDE

72" MAXCENTER TO CENTER

67"

2.0

70.1

73.0

A

B

C

D

D

DETAIL A

FOR ADDITIONAL ATTACHMENT STRENGTH POST CAPS CAN BE SECURED TO POST USING A #8 X 3/4" TRUSS HEAD SCREW OR 18 GAUGE BRAD NAIL. WHEN USING SCREWS IT IS RECOMMENDED TO PILOT DRILL HOLE IN CAP PRIOR TO INSTALLING SCREWS. WHEN INSTALLING SCREWS BE CAREFULL NOT TO OVER TIGHTEN AND DAMAGE POST CAP.

1.00TYP

1.00TYP

2X .63TYP

.125TYP

DETAIL B

2.56TYP

.63TYP

DETAIL C

5.00

SECTION D-D

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFNATURES COMPOSITES, LLC. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFNATURES COMPOSITES, LLC. IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

DIMENSIONS ARE IN INCHESTOLERANCES:FRACTIONAL: 1/16"ANGULAR: MACH 1 BEND 5TWO PLACE DECIMAL : .010THREE PLACE DECIMAL: .005

INTERPRET GEOMETRICTOLERANCING PER:

MATERIAL

FINISH

AS SPECIFIED

-

DRAWN

ENG APPR.

COMMENTS:

DATE

TITLE:

SIZE

BDWG. NO. REV

UNLESS OTHERWISE SPECIFIED:

-

J.T. MITCHELL 07/17/2015

07/16/2015

SHEET 2 OF 2

100005DO NOT SCALE DRAWING

HORIZONTAL BASKET WEAVE

J.T. MITCHELL

NAME

FENCE ASSEMBLY6 FT TALL X 6 FT WIDE