network devices repeaters, hubs, bridges, switches, routers
DESCRIPTION
TRANSCRIPT
![Page 1: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/1.jpg)
Network Devices
Repeaters, hubs, bridges, switches, routers, NIC’s
![Page 2: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/2.jpg)
Devices and the layers at which they operate
Layer Name of Layer Device
3 Network Routers, layer 3 switches
2 Data Link Switches, bridges, NIC’s
1 Physical Hubs
![Page 3: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/3.jpg)
NIC’s (Network Interface Cards)
This NIC has interfaces for twisted pair, thicknet, and thinnet connectors.
![Page 4: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/4.jpg)
Repeaters
Signal attenuation or signal loss – signal degrades over distance
Repeaters clean, amplify, and resend signals that are weakened by long cable length.
Built-in to hubs or switches
![Page 5: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/5.jpg)
Hubs
OSI layer 1 hardware Hubs regenerate and retime network signals Hubs propagate signals through the network They cannot filter network traffic They cannot determine best path They are used as network concentration points They are really multi-port repeaters Uplink port – crossover mode or straight through
mode
![Page 6: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/6.jpg)
Bridges
A layer 2 device designed to create two or more LAN segments, each of which is a separate collision domain.
The purpose is to filter traffic on a LAN, to keep local traffic local, yet allow connectivity to other segments of the network.
Filter traffic by looking at the MAC address Frame filtering
![Page 7: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/7.jpg)
Bridges
If the frame is addressed to a MAC address on the local side of the bridge, it is not forwarded to the other segment
MAC addresses on the other segment are forwarded
Bridges maintain a MAC address table for both segments they are connected to
![Page 8: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/8.jpg)
Cycle of bridges
Bridged network can span many segments Broadcasts are sent to all segments
![Page 9: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/9.jpg)
BridgesDistributed Spanning Tree
If all bridges forward broadcasts, infinite loops can occur
Bridges perform DST on boot to determine which bridges will not forward broadcasts
![Page 10: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/10.jpg)
Switched networks
Shared ethernet networks perform best when kept to 30-40 percent full capacity
This is a result of CSMA/CD A LAN switch is a high-speed multiport bridge
which segments each port into its own collision domain and can access the full bandwidth
![Page 11: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/11.jpg)
Devices and the layers at which they operate
Layer Name of Layer Device
3 Network Routers, layer 3 switches
2 Data Link Switches, bridges, NIC’s
1 Physical Hubs
![Page 12: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/12.jpg)
Switches
Each port is a simulated segment to itself
![Page 13: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/13.jpg)
Store and Forward Switches
Do error checking on each frame after the entire frame has arrived into the switch
If the error checking algorithm determines there is no error, the switch looks in its MAC address table for the port to which to forward the destination device
Highly reliable because doesn’t forward bad frames Slower than other types of switches because it holds
on to each frame until it is completely received to check for errors before forwarding
![Page 14: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/14.jpg)
Cut Through Switch
Faster than store and forward because doesn’t perform error checking on frames
Reads address information for each frame as the frames enter the switch
After looking up the port of the destination device, frame is forwarded
Forwards bad frames Performance penalty because bad frames can’t
be used and replacement frames must be sent which creates additional traffic
![Page 15: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/15.jpg)
Fragment free cut through switch
Combines speed of cut through switch with error checking functionality
Forwards all frames initially, but determines that if a particular port is receiving too many bad frames, it reconfigures the port to store and forward mode
Preferred switching solution
![Page 16: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/16.jpg)
Unmanaged/Intelligent switches
Unmanaged – provides LAN’s with all the benefits of switching
Fine in small networks Intelligent switches tracks and reports LAN
performance statistics Have a database ASIC (application specific
integrated circuit) on board to collect and store data which you view through a software interface
![Page 17: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/17.jpg)
Layer 3 switch
By definition a switch filters or forwards frames based on MAC addresses. This makes a switch a layer 2 device.
Now we have layer 3 switches which have routing capability. If a data frame can’t be switched it is routed.
Each port is a separate LAN port, but the forwarding engine actually calculates and stores routes based on IP addresses, not MAC addresses
Usually support only IP or IP and IPX
![Page 18: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/18.jpg)
VLAN Switches
Virtual local area network Each port on a switch defines a collision domain The entire switch forms a single broadcast domain VLANs can define multiple broadcast domains Network traffic that is directed to all computers on
the network can be segmented to transmit only on a specific VLAN.
Improves bandwidth on a the VLAN’s because each VLAN filters the network-to-network broadcast traffic as well as the collision traffic from other VLAN’s
![Page 19: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/19.jpg)
Physical Layer Broadcast
Physical layer broadcasts – implemented by non-switched Ethernet networks through shared cabling and hubs Each bit that is transmitted is physically received
by every station Switches and VLAN’s don’t do physical layer
broadcasts
![Page 20: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/20.jpg)
MAC-level broadcast
MAC-level broadcast – deal with how to handle MAC level broadcast frames; that is the data frames that have a broadcast destination MAC address
MAC-level broadcast frames are addressed to all MAC addresses on a given network (not a network segment, but an actual network as defined by its network address)
A regular switch forwards all broadcast frames out all ports, but a VLAN switch forwards broadcast frames only to ports that are part of the same VLAN
Multiple switches can be part of the same VLAN
![Page 21: Network Devices Repeaters, hubs, bridges, switches, routers](https://reader033.vdocuments.net/reader033/viewer/2022061206/548266aab47959000d8b47c3/html5/thumbnails/21.jpg)
VLAN Switches
None of the VLAN’s can communicate unless each VLAN is connected to a router or layer 3 switch
Each VLAN is separating collision traffic associated with MAC Addresses (layer 2) and each VLAN is separating the network-to-network broadcast traffic. In other words each VLAN is acting as a separate network so a layer 3 device is necessary for them to communicate