new approach to predict hugoniot … · the hugoniot curve is found in the book explosives...
TRANSCRIPT
DRDC-RDDC-2014-N35
NEW APPROACH TO PREDICT HUGONIOT PROPERTIES OF
EXPLOSIVES MATERIALS
Mounir Jaidann, Dennis Nandlall, Amal Bouamoul and Hakima Abou-Rachid
Defence R&D Canada, 2459, De la Bravoure Road, Quebec, QC. G3J 1X5, Canada
© Her Majesty the Queen in Right of Canada, as represented by the Minister of National Defence, 2014 © Sa Majesté la Reine (en droit du Canada), telle que représentée par le ministre de la Défense nationale, 2014
Abstract
To characterise explosives materials, investigations for four well experimentally characterised energetic
materials, Cyclotrimethylenetrinitramine (RDX), Octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX),
Pentaerythritol tetranitrate (PETN) and Triamino-trinitrobenzene (TATB) were conducted using quantum
mechanics and analytical methods. Furthermore, using the pressure p and the ratio of specific densities,
v/v0, p-v Hugoniot diagrams of the four explosives were obtained. Using, the Stine equation [Stine, J.
Energ. Mater., 1990] and more recent least squares fitting algorithms, new constants were obtained, to
determine the detonation velocity, D, which was then used to define the Raleigh line. The ratio of specific
heats, γ, a value anywhere between 2 and 3 and usually approximated from experimental data, was
obtained by making the explosive products Hugoniot tangent to the Rayleigh line through varying γ. The
effect, sensitivity and importance of having the correct value of γ were demonstrated. The predicted
parameters namely the shock, particle and detonation velocities, the CJ pressure and density, the ratio of
specific heats and the Hugoniot diagrams all compared quite well with published experimental data.
1. Introduction
To better design energetic materials and predict their energy output and response it is necessary to
characterise these materials in terms of their energetics. Indeed, this characterisation demands a series of
experiments ranging from slow cook off of the material to high velocity flyer plate impact tests are
necessary to obtain parameters such as the detonation velocity, densities, shock and particle velocities and
critical pressures. These experimental parameters are required to obtain the Chapman-Jouguet parameters
that define the point at which the detonation occurs. The mean objective of this work is to conduct
numerical experiments to examine the parameters that define detonation process and establish a
DRDC-RDDC-2014-N35
completely numerical approach by using quantum mechanics and analytical methods. To this end, four
well known and experimentally characterised energetic materials were considered and the results
compared with experimental values. The four materials chosen are RDX, HMX, PETN and TATB. The
detonation velocity is one of the key performance characteristics of energetic materials which can be
determined by some computer codes [1-4]. Also, pressure-specific volume relationship called Hugoniot
curve is a valuable tool to understand the material response and evaluate their performance. A treatment of
the Hugoniot curve is found in the book Explosives Engineering by Cooper [5]. Each material has a
unique Hugoniot curve that is usually obtained from a series of experimental tests that could be quite
expensive and time consuming. In this work, the main focus was on the characterisation of the detonation
of the energetic materials (including the Hugoniot) using the numerical simulations technique. This
analysis method provided a valuable way to understand the detonation process and obtain theirs
corresponding parameters. The computation of detonation parameters by computer codes usually requires
the heat of formation ΔHf and the density of energetic materials; therefore, the knowledge of heat of
formation of materials remains the key issue. In this work, the hybrid density-functional theory (DFT) [6]
approach was used to predict heats of formation in the solid phase and detonation properties using
quantum chemistry calculations.
2. Computational methods and details
All calculations on structural properties of compounds, were carried out in the framework of density-
functional theory (DFT) [7]. In the present work, B3LYP hybrid functional [8-10] was used in conjunction
with 6-311++G(3d,3p) basis sets. The geometry of molecules were optimized using gradient techniques at
the HF/STO-3G, HF/6-31G, B3LYP/6-311G, and B3LYP/6-311++G(3d,3p) levels without symmetry
constraints. All calculations were performed using the Gaussian 03 [11] packages. The B3LYP functional
is a reliable method providing accurate results when compared to experimental data and ab initio methods
[12].
In this study, heats of formation 0f SolidH∆ were determined using Hess’ law of constant heat summation
[13] given by:
0 0f Solid f Gas SubH H H∆ = ∆ − ∆ (1)
DRDC-RDDC-2014-N35
where 0f GasH∆ is the heat of formation at the gas phase predicted by using isodesmic reaction approach
[4]. In this approach, the number of electron pairs and chemical bond types are assumed to be conserved
in the chemical reaction.
The heat of sublimation, f SubH∆ , is estimated using Politzer approach [14]. Politzer et al. predict heats of
sublimation of a compound by considering a statistical approach where various parameters are mapped
onto isodensity surfaces of the isolated molecule, and propose an empirical expression which provides the
heat of sublimation of a particular compound given by:
( )0.52 21 2 3Sub totH Ab b νσ b∆ = + + (2)
where A is the molecular surface area. It is the collection of points where 97% of the electron density of
the isolated molecule is present. The parameter ν defines the balance value for the positive and the
negative potential quantities on the molecular surface A. 2 2 2+ −= +totσ σ σ represents the variance of
electrostatic potential values on the molecular surface and b1–3 represent the fit parameters computed from
least-square fitting techniques. The method proposed by Stine [15] to obtain the detonation velocity, D,
was used. A least squares fitting was applied to minimise the sum of the squares of the residuals formed
by the difference between the calculated and the experimental values and the newer fit constants were
estimated. The Rayleigh line and Hugoniot curve of gas products were obtained using the simplest theory
discussed by Fickett et al. [16]. The model assumes that the products of reactions are instantaneously
produced by the shock. The conservation of mass, momentum and energy equations were used and the gas
products of reaction were assumed as an ideal gas. The four materials to be characterised are RDX, HMX,
PETN and TATB and their chemical structures are illustrated in Figure 1.
Figure 1. Chemical structure of molecules in the studied system.
DRDC-RDDC-2014-N35
3. Results and discussion
3.1. Gas-phase heat of formation
In this work, only PETN molecule case is provided as an example for gas-phase heat of formation
calculations. The gas-phase heat of formation of PETN was estimated using isodesmic reactions given by
equation 3. Using the experimental 0f GasH∆ values of Nitroglycerin (NG) and Ethyl nitrate, 0
f GasH∆ of
PETN was calculated as follows:
(3)
The heat of reaction of this equation is given by:
( ) ( )2
0 0 0 0, , , ,∆ = ∆ + ∆ − ∆ + ∆rxn f Gas PETN f Gas H f Gas NG f Gas Ethyl nitrateH H H H H (4)
Using the experimental heat of formation of the molecules making up the PETN and available in NIST
website1, the PETN heat of formation can be calculated from equation 4:
2, , , ,∆ = ∆ + ∆ + ∆ − ∆f Gas PETN rxn f Gas NG f Gas Ethyl nitrate f Gas HH H H H H (5)
Heats of formation of the molecules in equation 3 are listed in Table 1.
Table 1. Experimental and calculated gas-phase heats of formation of the molecules making up the PETN
Molecules 0f GasH∆ , kcal/mol
NG -67 Ethyl nitrate -37
PETN -86 H2 0
3.2. Heats of sublimation
1 www.webbook.nist.gov/chemistry
DRDC-RDDC-2014-N35
For heats of sublimation, only PETN case is studied in this work. Table 2 lists some similar molecules to
PETN which have been used to determine the fit parameters b1–3 shown in equation 2. In the framework of
the Politzer approach, and the heats of sublimation SubH∆ were estimated. The experimental values of
SubH∆ , of the molecules used in the fit were taken from the website www.webbook.nist.gov/chemistry.
Politzer parameters shown in equation 2 are A, ν and σtotal and given in Table 2. Figure 2 shows the plot of
predicted SubH∆ of the selected molecules similar to PETN. The curve shows a good correlation between
the predicted and the measured data. The fitting procedure leads to b1 = 2 × 10-4 kcal/mol.Å4, b2 = 2.104,
and b3 = 0.2374 kcal/mol. b1-3 in equation (2) leads to, SubH∆ = 25.0 kcal/mol of PETN. Now using
equation (1), the heat of formation in the solid phase of PETN is estimated to be - 111 kcal/mol. The
experimental value as reported in reference [17] is -128 kcal/mol, the relative error between these two
values is about 15%. This deviation can be possibly reduced by using extended basis set in the hybrid
functional B3LYP.
Figure 2. Predicted heats of sublimation of the selected molecules versus the experimental values
Table 2. Molecular Properties.
Names Chemical structures A (Å2) ν σtotal (kcal/mol)
∆ subH (kcal/mol)
1,1,1,3-Tetranitro-2-methylpropane
235.350 0.125 10.963 91.200
DRDC-RDDC-2014-N35
1,1,1,4-Tetranitr obutane
227.320 0.1099 14.962 99.600
2,2,3,3-Tetranitrobutane
204.470 0.1351 12.394 78.200
Urea
95.830 0.2472 19.361 98.600
1,1,1,2,2-Pentanitropropane
228.030 0.0596 12.561 77.400
Ethyl carbamate
135.060 0.2167 16.026 76.300
Trinitromethane
147.910 0.0378 16.571 46.700
N-Nitrosobis-(2,2,2-trinitroethyl)amine
284.250 0.0521 18.059 23.326
DRDC-RDDC-2014-N35
N-Nitrobis-(2,2,2-trinitroethyl)amine
295.280 0.0581 13.891 24.720
3.3. Determination of the detonation velocity
Starting with the empirical method proposed by Stine [15] to obtain the detonation velocity, D, equation
(6), for a given compound:
00 1 2 3 4 5 /C N O H f SolidD D c n c n c n c n c H Mρ = + + + + + ∆ (6)
Where D0 is a constant, ni, i = C, N, O, H, are the specific number of atoms in the molecule, and ci, i = 1
to 5, are the corresponding characteristic constants for the carbon (C), nitrogen (N), oxygen (O) and
hydrogen (H) atoms in the molecule, and the heat of formation ( 0f SolidH∆ ), respectively. ρ is the density and
M is the molecular weight of the material. Equation (6) is expressed in terms of a set of known and well
characterised explosives, for which experimental detonation velocities, heats of formation and densities
are available. Using a least square fitting approach to equation (6), the constants D0 and ci could be
obtained. These constants can be used to predict the detonation velocities of new compounds that have
similar chemical composition.
3.4. Determination of constants D0 and ci
The base set of explosives compounds selected to obtain the constants D0 and ci are exactly the same five
known and well characterised explosives chosen by Stine in his original work [15]. These molecules are
BTNEU, HMX, TNETB, ABH and Exp1D. Table 3 shows the equivalent chemical names along with all
the necessary basic parameters such as the density, experimental detonation velocity, Dexp and molecular
weight that are required in equation (6).
Table 3. Chemical characteristics of BTNEU, HMX, TNETB, ABH, and Exp1D.
Chemical Formula Compound
Enthalpy of Formation (kcal/mol)
Density (g/cm3)
Mol Weight (g/mol) Dexp km/s
C24H6N14O24 ABH 116.3 1.78 874 7.60 C6H0N6O6 BTF 144.5 1.86 252 8.49 C5H6N8O13 BTNEU -72.9 1.86 386 9.01
DRDC-RDDC-2014-N35
C4H8N8O8 HMX 17.9 1.89 296 9.12 C6H6N6O14 TNETP -118.5 1.78 386 8.46 C6H6N4O7 Exp1D -94.0 1.55 246 6.85
In order to compute the detonation velocity D of RDX, HMX, PETN and TATB, parameters given in
Table 3 are used in equation (6) and then a least squares fitting is applied to minimise the sum of the
squares of the residuals formed by the difference between the calculated value of D and the experimental
value Dexp, and the D0, c1, c2, c3, c4 and c5 constants are estimated. The constants D0 and ci (i = 1 to 5)
obtained from the least squares fitting of equation (6) are given in Table 4.
Table 4. New data set of D0 and ci parameters to be used in equation (6).
D0 (km/s) c1 c2 c3 c4 c5 New data 2.96 -7.039 51.586 69.034 2.214 0.463 Stine 3.69 -13.85 37.74 68.11 3.95 0.6917
The least square fitting produced new data of the D0 and ci parameters that differ from Stine’s coefficients.
This deviation is simply due to the fact that in this work more optimized least square fitting algorithms
have been used.
Table 5. Detonation velocities using Stine and new constants in equation (6).
Compound Dexp km/s D/Stine km/s D /New data km/s
% of error, Stine data2
% of error, New data3
ABH 7.60 7.63 7.60 0.3990 0.0007 BTF 8.49 8.50 8.49 0.1415 0.0003 BTNEU 9.01 8.95 9.01 0.6775 0.0004 HMX 9.12 9.02 9.12 1.0090 0.0001 TNETB 8.46 8.48 8.46 0.2300 0.0006 Exp1D 6.85 6.86 6.85 0.1644 0.0000
From Table 5, the calculated % error using new data is lower than this using Stine’s values. For this raison
the named constants new data are used for all estimations of detonation velocities. The value of each term
in equation (6) has been determined, now it is possible to calculate the detonation velocities for the
selected explosives for this study – PETN, RDX, HMX and TATB. The experimental heats of formation
at the solid states, extracted from NIST website4, for RDX, HMX and TATB, have been used in equation
(6) for the calculations of the detonation velocities D. Table 6 shows a comparison between the calculated 2 % of error = 100* |(Dexp-D/Stine)|/Dexp 3 % of error = 100* |(Dexp-D/New Data)|/Dexp , in the case of the new constants 4 www.webbook.nist.gov/chemistry
DRDC-RDDC-2014-N35
and measured detonation velocities using equation (6) and very good agreement is obtained between
experimental and calculated values of D. Note that HMX was listed as a molecule in the Stine’s set.
Table 6. Detonation velocities for PETN, RDX, HMX and TATB
Chemical Formula Compound Dexp, km/s[5] D, km/s
C3H6N6O6 RDX 8.70 8.73 C4H8N8O8 HMX 9.12 9.12 C5H8N4O12 PETN 8.26 8.29 C6H6N6O6 TATB 7.76 7.91
3.5. Hugoniot curve and Rayleigh line
The Rayleigh line and Hugoniot curves of gas products are obtained using the simplest theory and are
discussed in many shock physics texts such as Fickett et al. [16]. The model assumes that the products of
the reaction are instantaneously produced by the shock. Using the conservation of mass, momentum and
energy equations, and the equation for Rayleigh line is:
( )( )
02 20
0
p - pρ D - = 0
v - v (7)
Which is expressed in terms of the specific volume v = 1/ρ , pressure and detonation velocity
For instance, an ideal gas is characterised with a constant heat capacity and a constant heat for its
complete reaction 0rq = ΔH and the Hugoniot curve that is expressed as,
2- 12 2 4 2
0 0 0 0
p v qμ μ μ μ = 0p v p v
λ+ − + −
, (8)
where µ2 = (γ - 1)/(γ + 1) and γ = Cp/Cv is the ratio of specific heats. λ is the degree of the chemical
reaction, changing from 0 for no reaction to 1 for a complete reaction. In this work, it is assumed that the
reaction is complete, then λ=1.
This is the equation of a rectangular hyperbola in the p/p0 - v/v0 plane, centered at the point v/v0 = µ2 and
p/p0 = - µ2.
If the Hugoniot curve equation (8) is solved simultaneously with the Rayleigh line equation (7), the
intersection of these two equations defines the CJ point at the detonation process. q represents the heat of
detonation; it can be estimated using quantum mechanical method [18]. In this work, the heat of
detonation q and the density ρ0 values are extracted from references [3, 19, 20] and used in equations (7)
and (8) to plot Hugoniot curves of gas products and Rayleigh lines. The line tangent at the CJ point (pCJ,
DRDC-RDDC-2014-N35
vCJ) is the Rayleigh line. The slope of line tangent at the CJ point and the Rayleigh line are equal. The
analytical results for the four explosives, at various corresponding values of γ, are presented in Figure 3.
3.6. The Gamma, γ, effect
The detonation process of an explosive the reaction occurs immediately and this implies that once the
unreacted material passes through the detonation wave. It is assumed that it is instantaneously converted
to a new material and as discussed previously the final state is determined by the intersection of equation
(8) and the Raleigh line equation (7). The correct value of γ which is the ratio of the specific heat at
constant pressure to that at constant volume (Cp/Cv) is important because it influences significantly the
tangent of the Hugoniot energy and as a result will influence the CJ point. As pointed out by Cooper [5],
an explicit value of γ is not available but experiments have shown that it ranges between 2 and 3. Many
texts provide approximate values for γ. However, in this work the idea was also to explore the influence of
γ on equation (8). For given values of p and v, γ was varied between 2 and 3 for the four explosives.
Figure 3 shows the effect of γ on equation (8) and its relation to intersecting the Raleigh line, for the four
molecules. In the case of PETN, when γ is equal to 2.2, the equation (8) intersects the Raleigh line at two
points A and B and as γ is gradually increased (around 2.55) at some point it is tangent to the Raleigh line
and if further increased (3.0) it stays above the Raleigh line. Similar analysis is observed for HMX, RDX
and TATB. In this way the CJ point for the four explosives were obtained and these are given in Table 7
and the results reported in Figure 3. The values of γ compare very well with published experimental data.
DRDC-RDDC-2014-N35
Table 7. Experimental and calculated properties of explosives.
ρ0 (kg/m3) γ pCJ (GPa)
Theo Exp [3] Theo Exp [3] RDX 1800 2.83 2.98 36.45 34.70 HMX 1900 2.89 3.00 40.60 39.30 PETN 1770 2.55 2.64 34.50 33.50 TATB 1895 3.00 2.72 29.23 31.50
Figure 3. Hugoniot curves to demonstrate the γ effect relative to the Raleigh lines for the four explosives.
4. Conclusions
Through the investigation conducted in this for four well experimentally characterised energetic materials,
RDX, HMX, PETN and TATB using quantum mechanics calculations coupled with analytical methods, it
is now possible to estimate some parameters such as the detonation velocity and the Chapman-Jouguet
pressure and density that define the detonation of a CHNO based explosives. . The detonation velocities of
explosives were obtained using Stine’s equation. However, new and seemingly more accurate constants
were obtained for this equation using instead a more optimized algorithm for a least squares fitting. With
these new accurate constants leading to precise predicted detonation velocities when they were compared
to experimental values. The specific heat ratio, a parameter found in the Hugoniot energy equation for the
products, and the Chapman-Jouguet pressures and specific densities were obtained for the studied
DRDC-RDDC-2014-N35
explosives using the point where the Raleigh line tangents to this Hugoniot diagram. The values obtained
for Chapman-Jouguet parameters and the specific heat ratios compared very well with published
experimental values for all four explosives. A sensitivity analysis of the specific heat ratio was examined
and it was shown that the tangent that energy Hugoniot makes with the Raleigh line is quite sensitive and
care needs to be taken in its determination since the Chapman-Jouguet parameters are determined using
this tangent point. To conclude, the potential use of the molecular modelling approach together with the
analytical methods shows that now a CHNO based explosives can be numerically characterised and
parameters such as CJ, specific heat ratio, γ, pCJ and detonation velocities can be obtained quite accurately
prior to experiments. This approach should be also as supporting information to suggest a minimum
number of or just confirmation experiments if necessary.
References
[1] M. Cowperthwaite, W.H. Zwisler, TIGER computer program documentation, Stanford Research Institute, SRI Pub. No: 2106, 1973.
[2] L.E. Fried, W.M. Howard, P.C. Souers, CHEETAH 2.0 user’s manual, in: Lawrence Livermore National Laboratory, Livermore, CA,, 1998.
[3] C.L. Mader, Numerical modeling of explosives and propellants, 3rd ed., CRC Press, Boca Raton, 2008.
[4] C.J. Cramer, Essentials of computational chemistry : theories and models, 2nd ed., Wiley, Chichester, 2004.
[5] P.W. Cooper, Explosives engineering, VCH, New York, N.Y., 1996.
[6] P. Politzer, P. Lane, M.C. Concha, Struct. Chem., 15 (2004) 469-478.
[7] R. G. Parr, Y. Weitao, Density-Functional Theory of Atoms and Molecules, Oxford University Press, New York, 1989.
[8] A.D. Becke, Phys. Rev. A,, 38 (1988) 3098.
[9] C. Lee, W. Yang, R.G. Parr, Phys. Rev. B,, 37 (1988) 785.
[10] B. Miehlich, A. Savin, H. Stoll, H. Preuss, Chem. Phys. Lett., 157 (1989) 200-206.
[11] M.J. Frisch, G.W. Trucks, H.B. Schlegel, G.E. Scuseria, M.A. Robb, J.R. Cheeseman, . . . J.A. Pople, Gaussian, Inc., Pittsburgh PA, 2003.
[12] B.M. Rice, S.V. Pai, J. Hare, Combust. Flame, 118 (1999) 445-458.
[13] P.W. Atkins, Physical chemistry, 2nd ed., Oxford University Press, Oxford, 1982.
[14] P. Politzer, J.S. Murray, Theor. Chem. Acc., 108 (2002) 134-142.
DRDC-RDDC-2014-N35
[15] J.R. Stine, J. Energ. Mater., 8 (1990) 41 - 73.
[16] W. Fickett, W.C. Davis, Detonation : theory and experiment, Dover Publications, Mineola, N.Y., 2000.
[17] D.L. Ornellas, J.H. Carpenter, S.R. Gunn, Rev. Sci. Instrum., 37 (1966) 907-912.
[18] B.M. Rice, J. Hare, Thermochim. Acta, 384 (2002) 377-391.
[19] J. Yinon, S. Zitrin, Modern methods and applications in analysis of explosives, Wiley, Chichester ; New York, 1993.
[20] P. Ravi, G.M. Gore, S.P. Tewari, A.K. Sikder, Int. J. Quantum Chem., (2011).