new horizon institute of technology & management ...i) he xagonal nut of m20 ii) he xagonal...
TRANSCRIPT
VBS_IEM_Modul-2_Assignme nt-2_2 4/01 /2018
Computer Aided Machine Drawing Practical
=======================================================================
PRACTICAL QUESTION:
Draw 2-D drawings (three views) and 3-D Models of following standard machine elements:i) Hexagonal Nut of M20ii) Hexagonal headed bolt of 100 mm long , 20 mm diameter for a thread length of 50 mm
iii) Square neck Stud of M20 whose total length is 100 mmiv) Draw assembly of Hexagonal headed bolt with Hexagonal nut and washer
Year: S.E Semester: III Academic Year: 2019-20 (Odd Semester)
Course Code: MTL306 Name of the Course: Computer Aided Machine Drawing
Practical No.: 01 Title: Machine Elements & Solid Geometry CO Covered: CO1,CO4
Batch No.: Date of Practical: Practical In-charge: Prof. R. T. Patle
New Horizon Education Society’sNew Horizon Institute of Technology & ManagementDepartment of Mechatronics EngineeringAnand Nagar, Kavesar, Off Ghodbunder Road, Thane (West)-400615
VBS_IEM_Modul-2_Assignme nt-2_2 4/01 /2018
Computer Aided Machine Drawing Practical
=======================================================================
PRACTICAL QUESTION:
Figure shows details of Single Tool Post. Prepare the 3-D model, assemble the components andDraw (a) F.V. and (b) T.V
Year: S.E Semester: III Academic Year: 2019-20 (Odd Semester)
Course Code: MTL306 Name of the Course: Computer Aided Machine Drawing
Practical No.: 02 Title: Details and assembly drawing of Machine Components CO Covered: CO1,CO2,CO3,CO4
Batch No.: Date of Practical: Practical In-charge: Prof. R. T. Patle
New Horizon Education Society’sNew Horizon Institute of Technology & ManagementDepartment of Mechatronics EngineeringAnand Nagar, Kavesar, Off Ghodbunder Road, Thane (West)-400615
VBS_IEM_Modul-2_Assignme nt-2_2 4/01 /2018
Computer Aided Machine Drawing Practical
=======================================================================
PRACTICAL QUESTION
Figure shows assembly of Pedestal Bearing. Draw the following details(a) Block :-i) F.V. ii) T.V. (b) Upper Brass: - i) F.V. ii) T.V. iii) L.H.S.V(c) Lower Brass : - i) F.V. ii) T.V. (d) Cap :- i) F.V. ii) T.V.
Year: S.E Semester: III Academic Year: 2019-20 (Odd Semester)
Course Code: MTL306 Name of the Course: Computer Aided Machine Drawing
Practical No.: 03 Title : Details and assembly drawing Bearings CO Covered: CO1,CO2,CO3,CO4
Batch No.: Date of Practical: Practical In-charge: Prof. R. T. Patle
New Horizon Education Society’sNew Horizon Institute of Technology & ManagementDepartment of Mechatronics EngineeringAnand Nagar, Kavesar, Off Ghodbunder Road, Thane (West)-400615
VBS_IEM_Modul-2_Assignme nt-2_2 4/01 /2018
Computer Aided Machine Drawing Practical
=======================================================================
PRACTICAL QUESTION
Figure shows assembly of Flanged Joint. Draw the following details(a) Right Flange :-i) F.V. ii) S.V. (b) Left Flange :-i) F.V. ii) S.V.(c) Bolt :- i) F.V. ii) T.V. (d) Nut : - i) F.V. ii) T.V.
Year: S.E Semester: III Academic Year: 2019-20 (Odd Semester)
Course Code: MTL306 Name of the Course: Computer Aided Machine Drawing
Practical No.: 04 Title : Details and assembly drawing of Pulley & Joints CO Covered: CO1,CO2,CO3,CO4
Batch No.: Date of Practical: Practical In-charge: Prof. R. T. Patle
New Horizon Education Society’sNew Horizon Institute of Technology & ManagementDepartment of Mechatronics EngineeringAnand Nagar, Kavesar, Off Ghodbunder Road, Thane (West)-400615
VBS_IEM_Modul-2_Assignme nt-2_2 4/01 /2018
Computer Aided Machine Drawing Practical
=======================================================================
PRACTICAL QUESTION
Figure shows details of Non return Valve. Prepare the 3-D model, assemble the components andDraw (a) Sectional F.V. and (b) T.V
Year: S.E Semester: III Academic Year: 2019-20 (Odd Semester)
Course Code: MTL306 Name of the Course: Computer Aided Machine Drawing
Practical No.: 05 Title : Details and assembly drawing of Valves & IC Engine CO Covered: CO1,CO2,CO3,CO4
Batch No.: Date of Practical: Practical In-charge: Prof. R. T. Patle
New Horizon Education Society’sNew Horizon Institute of Technology & ManagementDepartment of Mechatronics EngineeringAnand Nagar, Kavesar, Off Ghodbunder Road, Thane (West)-400615
VBS_IEM_Modul-2_Assignme nt-2_2 4/01 /2018
Computer Aided Machine Drawing Practical
=======================================================================
PRACTICAL QUESTIONS
Question1: Draw the 3-D model for parts of Physical Components (Square Tool Post) withactual measured dimensionQuestion 2: Assemble the parts of Square Tool Post and also draw Followings views
(a) F. V. and (b) T.V.
Year: S.E Semester: III Academic Year: 2019-20 (Odd Semester)
Course Code: MTL306 Name of the Course: Computer Aided Machine Drawing
Practical No.: 06 Title : Reverse Engineering of Physical Model CO Covered: CO1,CO2,CO3,CO4
Batch No.: Date of Practical: Practical In-charge: Prof. R. T. Patle
New Horizon Education Society’sNew Horizon Institute of Technology & ManagementDepartment of Mechatronics EngineeringAnand Nagar, Kavesar, Off Ghodbunder Road, Thane (West)-400615