new zealand standard 4121.1 toilet suites compliant … · when tested in accordance with standard...
TRANSCRIPT
TOILE T SUITES
13.01 CARE SUITES & PANS INSTALLATION GUIDE
CAROMA 13.02 LEDA CARE INVISI SERIES II® - Access and Mobility
13.03 CARE 400 - Access and Mobility
13.04 COSMO SOVEREIGN CARE - Access and Mobility
13.05 CARE 300 - Access and Mobility
13.06 CARE 200 - Access and Mobility
13.07 COSMO CARE - Access and Mobility
13.08 CARE 100 - Access and Mobility
13.09 TRIDENT SOVEREIGN CARE - Access and Mobility
N E W Z E A L A N D S TA N DA R D 4121.1
CO M PL I A N T PR O D U C T S
Suitable for installation to comply to New Zealand Standard NZS 4121.1 Design for access and mobility.
Suitable for installation to comply to New Zealand Standard NZS 4121.1 Design for access and mobility
Care Suites and PansInstallation Guide
Leda Care Pan Connector Pans
500 max.
450
600
min
.
1100
max
.
Note: Push button position must be either within the push button zone or on the centre line of the pan.
1100
max
.
600m
in.
460
300max.
300max.
Pushbuttonzone
Pushbuttonzone
Alternative side pushbutton positionfor remote push button
700 to 750mm forwheel chairaccess only
700 to 750mmrequirement for
wheel chairaccess only
460
top
of s
eat r
equi
rem
ent
1100
max
. req
uire
men
t
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
The Caroma Care Suites are designed to provide a raised seat height of 460mm for persons with X accessible applications. For compliance to NZS 4121.1 it is necessary to provide a pan projection of 700mm to 750mm to the front of the pan.
Important: Reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Seats: The following seats are specific for care installations: Colani disabled, Caravelle Care and Pedigree II Care which are available in Caroma White, Sorrento Blue and Anthracite Grey. Refer to specific product page for recommended seat.
Position of the Pan:
For wheel chair access the installed pan must be a minimum of 700 to 750mm maximum from the front of the pan to the finished wall and provide a seat height of 460mm.
All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant (15mm max. height) and fixed with corrosion resistant screws and pan guard washers.
Bracket fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with the D82 Fixing Brackets supplied.
Position of Cistern:
The height of the push button must be a minimum of 600mm and no greater than 1100mm to the top of the push button and positioned within the push button zone or on the centre line of the pan.
Installation: The installation of the toilet suite shall be in accordance with the normal minimum drainline grade requirements in AS/NZS 3500.2.
Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations. Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
Date April 2015 13.01
Suitable for installation to comply to New Zealand Standard NZS 4121.1 Design for access and mobility
®
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
Date April 2015 13.02
The 4.5/3 dual flush Leda Care Invisi Series II® matched suite is designed to provide a raised seat height of 460mm for accessible applications. For compliance to NZS 4121.1 it is necessary to locally extend the wall out to provide pan projection of 700mm to 750mm to the front of the pan. The pan connection system includes the patented Caroma Uni-Orbital® connector that extends to any position in a 25mm radius, unlike traditional connectors that only move backwards and forwards. The setout range is from 60mm – 170mm from the back of the pan with a recommended setout of 90mm. Concealed cistern and plumbing fittings provide space saving, ease of cleaning and performance matched components to maximise flushing efficiency.
Important : Reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Leda Care 4.5 litre full flush wash down box rim type.
Traps: Universal trap.
Inlet: 50mm back inlet. A 40mm kee-seal is available.
Cisterns: Invisi Series II® cistern – suitable for inwall, induct and inceiling applications. Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Invisi II Raised Care Buttons sold separately.
Seats: Caravelle Care double flap seat is provided as standard with this suite, and are available in Caroma White (W), Sorrento Blue (SB) and Anthracite Grey (AG).
Position of the Pan:
For wheel chair access, the installed pan must be a minimum of 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of Cistern:
The pan is suitable for installation with concealed cisterns providing the circulation space requirement is maintained. The height of the push button must be no greater than 1100mm to the top of the push button and positioned within the push button zone or on the centre line of the pan.
Colour: Pan available in white only.
Installation: The installation of the toilet suite shall be in accordance with the normal minimum drainline grade requirements in AS/NZS 3500.2.
Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations. Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
70mm min. for button and remote mounting box
450
355
420
150
700
to 7
50m
m R
equi
rem
ent
Extended wallinfill piece(not supplied)
400 max.Requirement
325
90
45
400
Note : All height dimensions to underside of pan, make allowance for mortar bedding.
600
– 11
00 re
quire
men
t
400
812
- 98
2
Integrated flush pipesupport
90
185
43046
0to
p of
sea
t req
uire
men
t
240
165
D82 ConcealedFixing Bracket
Care buttons
To increasecistern height use elevatedflush pipe kit(supplied)
Horizontal flushpipe extensionCode No.104242
55
Invisi Series II® cistern
25
to to
p of
flus
h pi
pe
supp
ort n
oggi
n
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
* Reference must be made to the NZS 4121.1 to confirm installation requirements.
Recommended 90 setout60 – 170 range(up to 25mm sideways adjustment)Uni-Orbital® connector
Note: The projection requirements detailed on this illustration are for wheel chair access only.
All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.Bracket fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with the D82 Fixing Brackets supplied.
Leda Care Invisi Series II® Toilet Suite with Seat: Code No. Seat colour:
Caravelle Care Double Flap Seat 719100 W, SB or AG
Leda CareInvisi Series II®
Sanitary Facilities - Access and Mobility
4.5/3 litre Dual Flush Toilet Suite with Wall Faced Pan and Invisi Series II® Cistern
DRAFT
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
®
Suitable for installation to comply to New Zealand Standard NZS 4121.1 Design for access and mobility
®
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
Care 400 Sanitary Facilities - Access and Mobility
4.5/3 litre Dual Flush Toilet Suite
A contemporary designed 4.5/3 litre dual flush Care 400 toilet suite installation designed to provide a raised seat height of 460mm for X accessible applications. The pan features a concealed trap which facilitates easy cleaning. The versatility of the Care 400 toilet suite makes it ideal for use by wheel-chair users including wheeled commode chairs.
Important: Further reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Trident Concealed Trap Care pan 4.5/3 litre full flush washdown type.
Traps: S-trap unvented only Code No.606310.
Inlet: 50mm back inlet.
Cistern: Sovereign 4 Star Cistern (wall fix version). Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Round Care Button - Metal (supplied). Other button options sold separately.
Inlet Valve and Overflow:
Standard Bottom Entry Cistern – available as right hand inlet which is interchangeable and incorporates the Apollo inlet valve. Internal overflow only.
Seats: Caravelle Care seat suppplied, available in Caroma White (W), Sorrento Blue (SB) and Anthracite Grey (AG).
Position of the Pan:
For wheel chair access, the installed pan must be 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of the Cistern:
The underside of the cistern must be 600mm minimum from the finished floor. The push button height must be no greater than 1100mm from the finished floor.
Colours: White only.
Installation: The installation of the toilet suite shall be in accordance with the normal minimum drainline grade requirements in AS/NZS 3500.2.
Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations. Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
700 - 750mm requirement forwheel chair access only
430
Flush pipe extensionCode No.104242
or ExtendedMid/Low flush pipe
Code No.405061
SovereignCistern
435
450
350
30
168
330
Fixi
ng c
entre
152
55Inlet196 Inlet
or overflow
1100
max
. req
uire
men
t to
top
of p
ushb
utto
n
1050
45036
4
300Fixing centre
20
Caroma CarePush button
Code No.687073C
605
Rec
omm
ende
d42
0
570
inle
t
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
Fini
shed
wal
l
200 - 250mmsetout
* Reference must be made to the NZS 4121.1 to confirm installation requirements.
460
top
of s
eat r
equi
rem
ent
Note: The projection requirements detailed on this illustration are for wheel chair access only.
All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with corrosion resistant screws and pan guard washers. Use Caroma pan fixing kit. Code No.601150.
Care 400 Toilet Suiteswith Caravelle Care Seat Code No. Seat colour:
Double Flap S trap 987901 W, SB or AG
Date April 2015 13.03
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
Suitable for installation to comply to New Zealand Standard NZS 4121.1 Design for access and mobility
®
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
Cosmo Sovereign Care
Sanitary Facilities - Access and Mobility
4.5/3 litre Dual Flush Toilet Suite
A contemporary designed 4.5/3 litre dual flush Cosmo Sovereign Care toilet suite installation designed to provide a raised seat height of 460mm for X accessible applications.The pan features a concealed trap which facilitates easy cleaning. The versatility of the Cosmo Care Pan Concealed Trap makes it ideal for use by wheel-chair users including wheeled commode chairs.
Important: Further reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Cosmo Care Pan Concealed Trap pan 4.5 litre full flush washdown type.Traps: S trap (WELS 4 star rated) or P trap (WELS 4 star rated). Unvented only.
Inlet: 50mm back inlet. Cistern: Sovereign 4 Star Cistern (wall fix version).
Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Round Care Button - Metal (supplied). Inlet Valve and Overflow:
Standard Bottom Entry Cistern – available as right hand inlet which is interchangeable and incorporates the Apollo inlet valve. Internal overflow only.
Seats: Caravelle Care seat supplied, available in Caroma White (W), Sorrento Blue (SB) and Anthracite Grey (AG).
Position of the Pan:
For wheel chair access, the installed pan must be 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of the Cistern:
The underside of the cistern must be 600mm minimum from the finished floor. The push button height should be no greater than 1100mm from the finished floor.
Colours: White only.Installation: The installation of the toilet suite shall be in accordance with the normal minimum
drainline grade requirements in AS/NZS 3500.2.Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations.
Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
700 - 750mm requirement forwheel chair access only
225 - 275setout
445
Flush pipe extensionCode No.104242
or ExtendedMid/Low flush pipe
Code No.405061
SovereignSmartflush 4.5/3 litre cistern
425
485
355
30
168
330
Fixi
ng c
entre
570
Inle
t
185
Fini
shed
wal
l
152
55Inlet
196 Inletor overflow
Caroma CarePush buttonCode No.687073
605
Rec
omm
ende
d42
0
1100
max
. req
uire
men
t to
top
of p
ush
butto
n10
50 re
com
men
ded
45036
4
300Fixing centre
20
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
460
top
of s
eat r
equi
rem
ent
* Reference must be made to the NZS 4121.1 to confirm installation requirements.
Note: The projection requirements detailed on this illustration are for wheel chair access only. All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with corrosion resistant screws and pan guard washers. Use Caroma pan fixing kit. Code No.601150.
Cosmo Sovereign Care Toilet Suites: Code No. Seat colour:
Caravelle Double Flap S trap 987916 W, SB or MG
P trap 987926 W, SB or MG
Date April 2015 13.04
A pedestal type 6/3 litre dual flush Care Pan installation designed to provide a raised seat height of 460mm for people with X accessible applications. The versatility of the Care Pan makes it ideal for use by wheel-chair users including wheeled commode chairs.
Important: Further reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Concorde Exposed Trap Care Pan 6 litre full flush washdown type.
Traps: S and P-trap unvented only. Slope of P-trap 95°
Inlet: 50mm back inlet.
Cistern: Sovereign 3 Star Cistern (wall fix version). Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Round Care Button - Metal (supplied). Other button options sold separately.
Inlet Valve and Overflow:
Standard Bottom Entry Cistern – available as right hand inlet which is interchangeable and incorporates the Apollo inlet valve. Internal overflow only.
Seats: Caravelle Care seat suppplied, available in Caroma White (W), Sorrento Blue (SB) and Anthracite Grey (AG).
Position of the Pan:
For wheel chair access, the installed pan must be a minimum of 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of the Cistern:
The underside of the cistern must be 600mm minimum from the finished floor. The push button height must be no greater than 1100mm from the finished floor.
Colours: Pan and cistern available in white only.
Installation: The installation of the toilet suite shall be in accordance with the normal minimum drainline grade requirements in AS/NZS 3500.2.
Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations. Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
700 - 750mm Requirement for wheel chair access only
213 - 263mmsetout
430
30
450
SovereignCistern
425
450
350
168
300Fixing centre
330
Fixi
ng c
entre
1100
max
. req
uire
men
t to
top
of p
ushb
utto
n
152
55Inlet196 Inlet
or overflow
1050
364
Flush pipe extensionCode No.104242
or ExtendedMid/Low flush pipe
Code No.405061
Caroma CarePush buttonCode No.687073
605
Rec
omm
ende
d
570
inle
t
420
185 Fi
nish
ed w
all
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
460
top
of s
eat r
equi
rem
ent
* Reference must be made to the NZS4121.1 to confirm installation requirements.
Note: The projection requirements detailed on this illustration are for wheel chair access only.
All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with corrosion resistant screws and pan guard washers. Use Caroma pan fixing kit. Code No.601150.
Care 300 Toilet Suites with Caravelle Care Seat Code No. Seat colour:
Double Flap S trap 987905 W, SB or AG
P trap 987903 W, SB or AG
4.0 litres per average flush
Licence No. 0001
Date April 2015 13.05
Care 300 Sanitary Facilities - Access and Mobility
6/3 litre Dual Flush Toilet Suite
Suitable for installation to comply to New Zealand Standard NZS 4121.1 Design for access and mobility
A contemporary designed 4.5/3 litre dual flush Care 200 toilet suite installation designed to provide a raised seat height of 460mm for X accessible applications. The pan features a concealed trap which facilitates easy cleaning. The versatility of the Care 200 toilet suite makes it ideal for use by wheel-chair users including wheeled commode chairs.
Important: Further reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Trident Concealed Trap Care pan 4.5 litre full flush washdown type.
Traps: S-trap unvented only Code No.606310.
Inlet: 50mm back inlet.
Cistern: Cosmo 4 Star Cistern – A one piece injection moulded tank with a removable lid. The inlet valve is the Apollo inlet valve which reduces noise during the filling cycle. Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Round Care Button - Plastic (supplied). Other button options sold separately.
Inlet and Overflow:
Inlet is in the RH position and is located on the underside of the cistern and is interchangeable. Overflow is internal as standard, an external overflow kit is available.
Seats: Caravelle Care seat supplied, available in Caroma White (W), Sorrento Blue (SB) and Anthracite Grey (AG).
Position of the Pan:
For wheel chair access, the installed pan must be a minimum of 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of the Cistern:
The underside of the cistern must be 600mm minimum from the finished floor. The push button height must be no greater than 1100mm from the finished floor.
Colours: White only.
Installation: The installation of the toilet suite shall be in accordance with the normal minimum drainline grade requirements in AS/NZS 3500.2.
Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations. Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
700 - 750mm requirement forwheel chair access only
430
Flush pipe extensionCode No.104242
or ExtendedMid/Low flush pipe
Code No.405061
435
450
350
152
450
20
Fini
shed
wal
l
660
Rec
omm
ende
d39
0
370Fixing centre
650
inle
t
200Inlet
345
Fixi
ng c
entre
30
1100
max
. req
uire
men
t to
top
of p
ushb
utto
n
1050
reco
mm
ende
d
Cosmo Smartflush cistern
Caroma Careplastic button
420
145
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
200 - 250mmsetout
460
top
of s
eat r
equi
rem
ent
* Reference must be made to the NZS 4121.1 to confirm installation requirements.
Note: The projection requirements detailed on this illustration are for wheel chair access only.
All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with corrosion resistant screws and pan guard washers. Use Caroma pan fixing kit. Code No.601150.
Care 200 Toilet Suites with Caravelle Care Seat Code No. Seat colour:
Double Flap S trap 987911 W, SB or AG
®
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
Date April 2015 13.06
Care 200 Sanitary Facilities - Access and Mobility
4.5/3 litre Dual Flush Toilet Suite
A contemporary designed 6/3 litre dual flush Cosmo Care toilet suite installation designed to provide a raised seat height of 460mm for X accessible applications The pan features a concealed trap which facilitates easy cleaning. The versatility of the Cosmo Care Pan Concealed Trap makes it ideal for use by wheel-chair users including wheeled commode chairs.
Important: Further reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Cosmo Care Pan Concealed Trap pan 6 litre full flush washdown type.Traps: S trap (WELS 3 star rated) or P trap (WELS 3 star rated). Unvented only.Inlet: 50mm back inlet. Cistern: Cosmo 3 Star Cistern – A one piece injection moulded tank with a removable lid.The
inlet valve is the Apollo inlet valve which reduces noise during the filling cycle. Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Round Care Button - Plastic (supplied). Other button options sold separately. Inlet and Overflow:
Inlet is in the RH position and is located on the underside of the cistern and is interchangeable. Overflow is internal as standard, an external overflow kit is available.
Seats: Caravelle Care seat supplied, available in Caroma White (W), Sorrento Blue (SB) and Anthracite Grey (AG).
Position of the Pan:
For wheel chair access, the installed pan must be 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of the Cistern:
The underside of the cistern must be 600mm minimum from the finished floor. The push button height should be no greater than 1100mm from the finished floor.
Colours: White only.Installation: The installation of the toilet suite shall be in accordance with the normal minimum
drainline grade requirements in AS/NZS 3500.2.Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations.
Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
700 - 750mm requirement forwheel chair access only
445
660
Rec
omm
ende
d39
0
Cosmo Smartflush4.5/3 litre cistern
425
485
355
145
345
Fixi
ng c
entre
152
450
420
200Inlet
370Fixing centre
1100
max
. req
uire
men
t to
top
of p
ushb
utto
n
1050
reco
mm
ende
d
Caroma Careplastic button
30
* Reference must be made to the NZS 4121.1 to confirm installation requirements. 225 - 275setout
Flush pipe extensionCode No.104242
or ExtendedMid/Low flush pipe
Code No.405061
185
Fini
shed
wal
l
20
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
460
top
of s
eat r
equi
rem
ent
Note: The projection requirements detailed on this illustration are for wheel chair access only. All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with corrosion resistant screws and pan guard washers. Use Caroma pan fixing kit. Code No.601150.
Cosmo Care Toilet Suiteswith Caravelle Care Seat Code No. Seat colour:
Double Flap S trap 987918 W, SB or AG
P trap 987928 W, SB or AG
Cosmo Care Sanitary Facilities - Access and Mobility
6/3 litre Dual Flush Toilet Suite
Date April 2015 13.07
4.0 litres per average flush
Licence No. 0001
Care 100 Sanitary Facilities - Access and Mobility
6/3 litre Dual Flush Toilet Suite
A pedestal type 6/3 litre dual flush Care 100 toilet suite installation designed to provide a raised seat height of 460mm for people with X acessible applications. The versatility of the Care 100 suite makes it ideal for use by wheel-chair users including wheeled commode chairs.
Important: Further reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Concorde Exposed Trap Care Pan 6 litre full flush washdown type.Traps: S and P-trap unvented only. Slope of P-trap 95°.Inlet: 50mm back inlet. Cistern: Cosmo 3 Star Cistern – A one piece injection moulded tank with a removable lid. The
inlet valve is the Apollo inlet valve which reduces noise during the filling cycle. Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Round Care Button - Plastic (supplied). Other button options sold separately. Inlet and Overflow:
Inlet is in the RH position and is located on the underside of the cistern and is interchangeable. Overflow is internal as standard, an external overflow kit is available.
Seats: Caravelle Care seat supplied, available in Caroma White (W), Sorrento Blue (SB) and Anthracite Grey (AG).
Position of the Pan:
For wheel chair access, the installed pan must be a minimum of 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of the Cistern:
The underside of the cistern must be 600mm minimum from the finished floor. The push button height must be no greater than 1100mm from the finished floor.
Colours: White only.Installation: The installation of the toilet suite shall be in accordance with the normal minimum
drainline grade requirements in AS/NZS 3500.2.Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations.
Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
43066
0 R
ecom
men
ded
390
45042
0
Flush pipe extensionCode No.104242
or ExtendedMid/Low flush pipe
Code No.405061
Cosmo Smartflush cistern
650
inle
t
345
Fixi
ng c
entre
200Inlet
370Fixing centre
145
30
1100
max
. req
uire
men
t to
top
of p
ushb
utto
n
1050
reco
mm
ende
d
Caroma Careplastic button
* Reference must be made to the NZS 4121.1 to confirm installation requirements.
700 - 750mm Requirement for wheel chair access only
213 - 263mmsetout
425
450
350
152
185 Fi
nish
ed w
all
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
460
top
of s
eat r
equi
rem
ent
Note: The projection requirements detailed on this illustration are for wheel chair access only.
All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with corrosion resistant screws and pan guard washers. Use Caroma pan fixing kit. Code No.601150.
Care 100 Toilet Suites: with Caravelle Care Seat Code No. Seat colour:
Double Flap S trap 987909 W, SB or AG
P trap 987907 W, SB or AG
4.0 litres per average flush
Licence No. 0001
Date April 2015 13.08
Date June 2010 4.1
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
®
Suitable for installation to comply to New Zealand Standard NZS 4121.1 Design for access and mobility
®
The morestars the morewater efficient
A joint government and industry program
litres per full flush
litres per half flush
4.53
3.5 litres per average flush
For more information and to compareproducts, refer to:
www.waterrating.gov.au
When tested in accordance with Standard AS/NZS 6400
WATERRATING
Licence No. 0001
Trident Sovereign
Sanitary Facilities - Access and Mobility
4.5/3 litre Dual Flush Toilet Suite
A contemporary designed 4.5/3 litre dual flush the Trident Sovereign toilet suite installation designed to provide a raised seat height of 460mm for X accessible applications. The pan features a concealed trap which facilitates easy cleaning. The versatility of the Trident Sovereign toilet suite makes it ideal for use by wheel-chair users including wheeled commode chairs.
Important: Further reference must be made to NZS 4121.1 with current amendments to determine circulation space, grab rail and installation requirements. The dimensions in this sheet may change with amendments to the standard.
Pan: Trident Concealed Trap Care pan 4.5/3 litre full flush washdown type.
Traps: S-trap unvented only Code No.606310.
Inlet: 50mm back inlet.
Cistern: Sovereign 4 Star Cistern (wall fix version). Important: Working pressure minimum 30kPa to maximum 1000kPa flow pressure. Rain water tank compliant.
Buttons: Round Care Button - Metal (supplied). Other button options sold separately.
Inlet Valve and Overflow:
Standard Bottom Entry Cistern – available as right hand inlet which is interchangeable and incorporates the Apollo inlet valve. Internal overflow only.
Seats: Colani seat suppplied, available in Caroma White (W) or Sorrento Blue (SB).
Position of the Pan:
For wheel chair access, the installed pan must be 700 to 750mm from the front of the pan to the finished wall and provide a seat height of 460mm.
Position of the Cistern:
The underside of the cistern must be 600mm minimum from the finished floor. The push button height must be no greater than 1100mm from the finished floor.
Colours: White only.
Installation: The installation of the toilet suite shall be in accordance with the normal minimum drainline grade requirements in AS/NZS 3500.2.
Dimensions: All dimensions are in millimetres and are subject to normal manufacturing variations. Caroma pursues a policy of continuing improvement in design and performance of its products. The right is therefore reserved to vary specifications without notice.
700 - 750mm requirement forwheel chair access only
430
Flush pipe extensionCode No.104242
or ExtendedMid/Low flush pipe
Code No.405061
SovereignCistern
435
450
350
30
168
330
Fixi
ng c
entre
152
55Inlet196 Inlet
or overflow
1100
max
. req
uire
men
t to
top
of p
ushb
utto
n
1050
45036
4
300Fixing centre
20
Caroma CarePush button
Code No.687073C
605
Rec
omm
ende
d42
0
570
inle
t
10m
m b
eddi
ng5m
m m
ax. s
ilicon
e
Fini
shed
wal
l
200 - 250mmsetout
* Reference must be made to the NZS 4121.1 to confirm installation requirements.
460
top
of s
eat r
equi
rem
ent
Note: The projection requirements detailed on this illustration are for wheel chair access only.
All height dimensions to underside of pan, make allowance for mortar bedding.
Mortar bedding: The pan should be fixed to the floor with a sand cement mixture of 3:1 to a depth of 60mm. When bedded the back of the foot of the pan should be approximately 10mm above the finished floor.
Screw fixing: The pan should be bedded with an acetic cured silicone sealant and fixed with corrosion resistant screws and pan guard washers. Use Caroma pan fixing kit. Code No.601150.
Trident Sovereign Toilet Suites with Colani Seat Code No. Seat colour:
Double Flap S trap 987895 W or SB
Date April 2015 13.09