notch filter
DESCRIPTION
Elecs lec 2TRANSCRIPT
![Page 1: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/1.jpg)
FILTER• An electrical network that alters the amplitude and/or
phase characteristics of a signal with respect to frequency• Ideally, a filter will not add new frequencies to the input
signal, nor will it change the component frequencies of that signal, BUT it will change the relative amplitudes of the various frequency components and/or their phase relationships.
• Often used to emphasize signals in certain frequency ranges and reject signals in other frequency ranges
![Page 2: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/2.jpg)
Low Pass High Pass
Bandpass Bandstop
FILTER TYPESLow Pass-blocks high frequencies
High Pass-blocks low frequencies
Bandpass-blocks high and low frequencies except in narrow band
Bandstop-blocks frequencies in a narrow band
![Page 3: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/3.jpg)
ACTIVE FILTERS• A type of analog electronic filter that uses active components such as
an amplifier• Amplifiers included in a filter design can be used to improve the performance
and predictability of a filter, while avoiding the need for inductors• Frequently use op amps so filter may have some gain as well. • Alternative to LRC-based filters
Benefits DisadvantageProvide improved characteristics Added complexitySmaller size and weight More design effortMonolithic integration in IC Implement without inductorsLower costMore reliableLess power dissipation
![Page 4: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/4.jpg)
2nd ORDER SYSTEM The order of a filter is the highest power of the variable s (poles) in
its transfer function. The order of a filter is usually equal to the total number of
capacitors and inductors in the circuit Higher-order filters will obviously be more expensive to build, since
they use more components, and they will also be more complicated to design.
However, higher-order filters can more effectively discriminate between signals at different frequencies
![Page 5: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/5.jpg)
Second-Order Filter Functions
![Page 6: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/6.jpg)
Stop Band Filters (SBF) The Band Stop Filter, (BSF) is another type of frequency selective
circuit that functions in exactly the opposite way to the Band Pass Filter we looked at before.
It passes all frequencies with the exception of those within a specified stop band which are greatly attenuated.
Name Convention: A narrow-band bandstop filter will be referred to as a Notch Filter and the wideband bandstop filter will be referred to as Band-reject Filter.
![Page 7: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/7.jpg)
Stop Band Filters (SBF) have two cut-off frequencies, commonly known as the -3dB or
half-power points producing a wide stop band bandwidth between these two -3dB points.
Then the function of a band stop filter is too pass all those frequencies from zero (DC) up to its first (lower) cut-off frequency point ƒL, and pass all those frequencies above its second (upper) cut-off frequency ƒH, but block or reject all those frequencies in-between.
BW = ƒH – ƒL
So for a wide-band band stop filter, the filters actual stop band lies between its lower and upper -3dB points as it attenuates, or rejects any frequency between these two cut-off frequencies.
![Page 8: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/8.jpg)
Band Stop Filter Response
![Page 9: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/9.jpg)
![Page 10: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/10.jpg)
![Page 11: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/11.jpg)
Band Stop Filter Characteristics
![Page 12: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/12.jpg)
Band Stop Filter Circuit
![Page 13: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/13.jpg)
There are many circuit topologies that can be used for very narrow notch filters, including:• Twin-T• Fliege• Wien-bridge• State-variable.
![Page 14: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/14.jpg)
TWIN-T NOTCH FILTER• The twin-T (or twin-tee) filter is essentially a notch
(band stop) filter.• It can still give an extremely high Q notch without the
use of any opamps.• In theory, the notch depth is infinite at the tuning
frequency, but this is rarely achieved in practice.• Notch depths of 100dB are easily achieved, and are
common in distortion analysers.• If the notch is placed at the fundamental frequency of
the applied signal, it is effectively removed completely, so any signal that is measured is noise and distortion.
![Page 15: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/15.jpg)
• The twin-T notch requires extraordinary component precision to achieve a complete notch, and for this reason it's not often recommended. However, it is without doubt one of the best filters to use when a very deep notch is needed - especially for completely passive circuits.
![Page 16: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/16.jpg)
![Page 17: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/17.jpg)
EXAMPLE PROBLEM
![Page 18: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/18.jpg)
SOLUTION
![Page 19: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/19.jpg)
SOLUTION
![Page 20: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/20.jpg)
ANSWER
![Page 21: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/21.jpg)
FLIEGE NOTCH FILTER• Normally, the Fliege Filter is something of an oddity, but
it makes an easily tuned notch filter with variable Q.• Notch depth is not as good as a twin-T, but it can be
tuned with a single resistor (within limits).
![Page 22: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/22.jpg)
ACTIVE WIEN ROBINSON NOTCH FILTER• The Wien-Robinson bridge in the figure below is a passive
band-rejection filter with differential output.• The output voltage is the difference between the potential
of a constant voltage divider and the output of a band-pass filter.
• Its Q-factor is close to that of the twin-T circuit.• To achieve higher values of Q, the filter is connected into
the feedback loop of an amplifier.
![Page 23: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/23.jpg)
ACTIVE WIEN ROBINSON NOTCH FILTER• The active Wien-Robinson filter in the figure has the
transfer function:
![Page 24: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/24.jpg)
ACTIVE WIEN ROBINSON NOTCH FILTER
![Page 25: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/25.jpg)
ACTIVE WIEN ROBINSON NOTCH FILTER
![Page 26: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/26.jpg)
ACTIVE WIEN ROBINSON NOTCH FILTER• In comparison to the twin-T circuit, the Wien-Robinson
filter allows modification of the• passband gain, A0, without affecting the quality factor, Q.• If fm is not completely suppressed due to component
tolerances of R and C, a fine-tuning• of the resistor 2R2 is required.
![Page 27: Notch Filter](https://reader031.vdocuments.net/reader031/viewer/2022012310/56d6bf5e1a28ab301695f6dc/html5/thumbnails/27.jpg)
SUMMARY:• An ideal band stop filter has a frequency response
which is the inverse of the band-pass filter.• Band stop filters block or “reject” frequencies that lie
between its two cut-off frequency points ( ƒL and ƒH ) but passes all those frequencies either side of this range. The range of frequencies above ƒL and below ƒH is called the stop band.
• Band Stop Filters have many uses in electronics and communication circuits and as we have seen here, they can be used to remove a band of unwanted frequencies from a system, allowing other frequencies to pass with minimum loss. Notch filters can be highly selective and can be designed to reject or attenuate a specific frequency or harmonic content generating electrical noise, such as mains hum within a circuit.