nz’s indust rial suppl y specialists suppliers to indust ry · bolts and fasteners. our cordless...

Your local TradeZone Store

www.tradezone.co.nz

Proud Sponsors of

n Z ’ S i n d u S T r i a l S u p p l Y S p e c i a l i S T S

e xc l u s i v e to t r a d e zo n e

VOl 172 feb-mar2 0 2 0

S u p p l i e r S TO i n d u S T r Y

2

36V BRUSHLESS MULTI VOLT 3 TOOL COMBOKC36DRBL(GKZ)

This highly innovative high powered and high precision 36V 138Nm Impact Drill, 36V 125MM Angle Grinder & 18V 305Nm Impact Wrench kit is the most advanced drill/grinder/wrench kit available with high-tech features,new high-tech brushless motors for more performance, durability and reliability. This absolute power house kit is powered by HiKOKI's most advanced Multi Volt battery technology and 32min Rapid Smart Charger.

$1,33212$1,531.94 GST Incl.

+GST

BONUSBattery via Redemption

$23625$271.69 GST Incl.

+GST

HIKOKI 230MM ANGLE GRINDER 2200WG23SW2(G1Z)

High-performance 2200W Motor, High overload durability due to new heat resistant motors, New labyrinth air vent design provides more protection for motor from grit and dirt contamination, Soft grip trigger handle, Supplied without grinding wheel.

AC BRUSHLESS 125MM ANGLE GRINDER - 1320W SLIM BODY VARIABLE SPEEDG13VE(G1Z)

HiKOKI's high performance AC brushless motor New slim-body design. AC brushless provides stable performance when used with generators and isn't affected by voltage drops from long extension leads. Variable speed control dial, select between 2,800/min and 10,000/min depending on your application.

$34900$401.35 GST Incl.

+GST

125MM ANGLE GRINDER 900WG13SN2(G6Z)

125mm (5”) Angle Grinder, high performance, Carry Case 900W

$11875$136.56 GST Incl.

+GST

115MM ANGLE GRINDER 900WG12SN2(G6Z)

115mm (4 1/2”) Angle Grinder, high performance, Carry Case 900W

$11000$126.50 GST Incl.

+GST

36V 1/2” BRUSHLESS IMPACT WRENCH 1050NM36V extreme power and durability to outperform the competition in the most demanding tasks. Delivering you 1050Nm tightening torque and 1650Nm nut busting torque with 4-stage tightening mode selector. IP56 Dust and Water Resistant. Built to out-perform the rest.

HIKOKI MULTI PORT RAPID CHARGERUC18YTSL(H0Z)

4 Charging Ports. Switchable Charging Modes - Simultaneous or Sequential. Suitable for charging ALL Hitachi and HiKOKI 18V and 36V Multi-Volt batteries. 52min charging 1440W battery - 32min charging 1080W battery.

$24875$286.06 GST Incl.

+GST

$51125$587.94 GST Incl.

+GST

Code Description +GST InclusiveWR36DA(G4Z) 36V 3/4" Brushless Impact Wrench 1100Nm BARE TOOL $459.00 $527.85WR36DA(GRZ) 36V 3/4" Brushless Impact Wrench 1100Nm Kit $825.00 $948.75

Code Description +GST InclusiveWH36DB(G4Z) HiKOKI 36v Brushless Triple Hammer Impact Drivers BARE TOOL $336.25 $386.69WH36DB(GGZ) HiKOKI 36v Brushless Triple Hammer Impact Drivers $773.75 $889.81

Code Description +GST InclusiveWR36DB(G4Z) 36V 1/2" Brushless Impact Wrench 1050Nm Kits BARE TOOL $423.75 $487.31WR36DB(GRZ) 36V 1/2" Brushless Impact Wrench 1050Nm Kits $761.25 $875.44

36V 3/4” BRUSHLESS IMPACT WRENCH 1100NM

36V BRUSHLESS TRIPLE HAMMER IMPACT DRIVER

Tightening Torque 1,100Nm / Nut Busting Torque 1,800Nm. 4 Power Mode Selector – 400 / 600 / 800 / 1,100Nm. IP56 Dust-proof & Water-proof. Kit supplied with 2x 1080W super high powered Multi Volt batteries, 32min Rapid Charger and carry case.

Triple Hammer design For higher Torque and better control. Powerful 210Nm of Torque, 4-Mode Power selector. Supplied with 2x 1080W Multi Volt batteries, 32min. Rapid Smart Charger and 2 x Case.

Code Description +GST InclusiveC3607DA(G4Z) 36V 185mm High Torque Brushless Circular Saw Kits BARE TOOL $411.25 $472.94C3607DA(GVZ) 36V 185mm High Torque Brushless Circular Saw Kits $886.25 $1,019.19

36V 185MM BRUSHLESS CIRCULAR SAW185mm Blade - max cut 62mm at 90°Equal cutting speed to AC powered sawsBest in class cutting thrust force of 11kgf*Silent mode allows for quieter operation.

HIKOKI AC BRUSHLESS 28MM SDS+ ROTARY HAMMER DRILLDH28PEC(G1Z)

High efficiency and maintenance-free AC Brushless motorVery compact and lightweight thanks to its renewed design3 modes: Drilling, Rotary Hammering and Demolition functionsProgrammable auto-stop function for continuous and repetitive drilling work.

3

BONUSM18JSR-0

$41563$477.97 GST Incl.

+GST

M18 FUEL TORQUE WRENCH 1/2 RINGM18FHIWF12-0

Gen 2 brushless high torque impact wrench now with 1354Nm of fastening torque, Yes you read that right 1354nm from a cordless tool.

$75565$869.00 GST Incl.

+GST

$25000$287.50 GST Incl.

+GST$40469$465.39 GST Incl.

+GST

$40469$465.39 GST Incl.

+GST

M18 FUEL TORQUE WRENCH 1/2IN FR 5.0AH KITM18FHIWF12-502C

M18 FUEL High Torque ½” Impact Wrench with Friction Ring provides a full corded replacement delivering 1354Nm of fastening torque and 1897Nm of nut-busting torque.

$46312$532.59 GST Incl.

+GST

M18 ONE-KEY HTIW 3/4 SKINM18ONEFHIWF34-0

Set the Torque , power and even track your tool, POWERSTATE™ Brushless motor delivers up to 1627Nm of fastening torque and 2034Nm of nut-busting torque.

$80750$928.63 GST Incl.

+GST

$60124$691.43 GST Incl.

+GST

$1,50312$1,728.59 GST Incl.

+GST$12500$143.75 GST Incl.

+GST

$13875$159.56 GST Incl.

+GST

M18 ONE-KEY HTIW 3/4 5.0AH KIT M18ONEFHIWF34-502C

M18 FUEL 3/4" Impact Wrench Kit POWERSTATE™ Brushless motor delivers up to 1627Nm of fastening torque and 2034Nm of nut-busting torque.

M18 CORDLESS GREASE GUN - 2.0AH KIT M18GG-201B

M18 FUEL 4PC (FPD,FID,CAG,FHIWF12) 5.0A M18FPP4B2-502B

M18 FUEL 3PC KIT(FPD FID CAG125XPD) 5AH M18FPP3A2-502B

1 X M18FPD2-0, 1 X M18CAG125XPD-0, 2 X M18B5, 1 X M12-18FC. 1 X Contractors Bag

M12 FUEL RIGHT ANGLE DIE GRINDER M12FDGA-0

M12 FUEL 1/2" IMPACT WRENCH 2.9AH KIT M12FIWF12-202B

FASTENING TORQUE 339Nm. Our M12 FUEL™ 3/8" Stubby Impact Wrench is the industry's most compact cordless impact wrench. The compact impact delivers high torque with our POWERSTATE™ brushless motor. The impact wrench delivers an industry leading 339Nm of nut-busting torque. This allows

M12 STARTER PACK 1X2.0AH/1XC12C M12SP-201B

12V/18V DUAL FAST CHARGER TOOL ONLY M12-18FC

you to remove even the most stubborn bolts and fasteners. Our cordless impact wrench features built-in REDLIINK™ tool technology to help you get the job done.

$1,21406$1,396.17 GST Incl.

+GST BONUSM18FHZ-0

M12 FUEL 3/8" IMPACT WRENCH 2.0AH K M12FIW38-202B

Our M12 FUEL® 1/2" Stubby Impact Wrench is the industry's most compact cordless impact wrench. The compact impact delivers high torque with our POWERSTATE™ brushless motor. The impact wrench delivers an industry leading 339Nm of nut-busting torque. This allows you to remove even the most stubborn bolts and

fasteners. Our cordless impact wrench features built-in REDLIINK™ PLUS tool technology to help you get the job done.

4

18V LXT BL GRINDER 125MM - SKIN ONLYDGA506Z

• High performance Brushless DC motor

• Automatic Torque Drive• Kick back detection - shuts

tool off if jamming occurs

• Soft start• Electric brake• Battery protection circuit• Battery fuel gauge

$26000$299.00 GST Incl.

+GST

$1866$21.46 GST Incl.

+GST

18V LXT BL KIT DTW1002+DHP481DLX2249TJ

DTW1002 - 1000NmDHP481 - 125Nm2x BL1850B (5.0Ah battery)Rapid ChargerMAKPAC Case

$92957$1,069.00 GST Incl.

+GST

BROWGUARD/LENS/CHINGUARDB-10/FC-93Extra long faceshield with chinguard. 394mm x 230mm long 1.0mm thick.Clear. Accepts C3 chin guard Heat and Impact.

SAFETY SPEC AZSPECT CLEAR UV400SM-9800CVery lightweight one piece polycarbonate lens, comfort nose piece, Antifog

COMFORT LINK CENTRE OR ENDCLC9065/CLE9065Made from high quality polyurethane, Excel-lent anti-fatigue properties, Ideal for counters or workbenches, Interlocks to create longer lengths, Easy to clean and move around

TRADE FLAME SWIVEL BLOW TORCH KITJP217034• High quality brass and steel fittings • Ergonomic handle design for precise operation • Solders 3.18 to 76mm (1/8 -3") copper pipe • Brazes 1.5 to 25.4mm (1/16 - 1") copper pipe • Adjustable On/Off and variable control valve

TRADEFLAME TURBO TORCH KITJP217045• High quality brass and steel fittings • Ergonomic handle design for precise operation • Solders 3.18 to 76mm (1/8 -3") copper pipe • Brazes 1.5 to 25.4mm (1/16 - 1") copper pipe • Adjustable On/Off and variable control valve • Full function flame even when inverted

SAFETY SPEC AZSPECT SMOKESM-9800S

$336$3.86 GST Incl.

+GST

$7090$81.54 GST Incl.

+GST$15652$180.00 GST Incl.

+GST

$16866$193.96 GST Incl.

+GST

$336$3.86 GST Incl.

+GST

ELVEX VALUE MUFF CLASS 4HB-25

Soft and pliable SuperSeal™ ear cushions. Low headband force and light-weight.

$1492$17.16 GST Incl.

+GST

AS/NZS 127025 dB Certified NRR to ANSI S3.19-1974.28 dB Certified SNR to CE EN 352-1.

DISP DUST/MIST MASK WITH BLUE VALVELightweight and Comfortable to wear. Ergonomically Moulded shape for a Custom seal. Welded Twin Straps. Metal Free Latex Free. Advanced Low Resistance exhalation valve.

$1298$14.93 GST Incl.

+GST

EP-22021B P2 (Box 12)

Code Description +GST InclusiveBAR005 3M Safety Aluminium Barrier $223.13 $256.60BAR006 5M Safety Aluminium Barrier $380.60 $437.69

Code Description +GST InclusiveSP25DAU 25W/240V $56.00 $64.40SP40DAU 40W/240V $60.66 $69.76SP80DAU 80W/240V $65.37 $75.18SP120DAU 120W/240V $102.69 $118.09SP175DAU 175W/240V $112.06 $128.87SP250DAU 250W/240V $112.06 $128.87

SAFETY ALUMINIUM BARRIER3M: Closed Length : 250mm / Yellow and Black5M: Closed Length : 510mm / Height 950mm / Yellow and Black

WELLER TRADE SOLDERING IRONS

WORKDECK MATS Heavy duty anti-fatigue mat, Holes for drainage, Bevelled edges to prevent tripping, About 25mm thick, Ideal for industrial work areas around machinery.

Code Description +GST InclusiveWDB12080 1200 x 800mm $71.80 $82.57WDB15010 1500 x 1000mm $115.90 $133.28

5

BENCH STONES66253183432 200X50X25m PAIB88 Non-Oil Fill Comb 120g /180g Ali-Oxide Bench Stone

STRIP-IT DISCS

Code Size +GST InclusiveBSD100 Strip-It Disc 100x16 $11.34 $13.04BSD115 Strip-It Disc 115x22 $12.06 $13.87BSD127 Strip-It Disc 127x22 $13.98 $16.08

Code Size +GST InclusiveFASTCUTJ Polishing Compound Grey Fastcut Large $11.60 $13.34MULTISHINEJ Polishing Compound Blue Multishine Large $14.64 $16.84TRIPOLIJ Polishing Compound Brown Tripoli Large $10.36 $11.91

POLISHING COMPOUNDS

Code Size +GST InclusiveJPD125C Disc Abrasive Flap-127mm Coarse $17.31 $19.91JPD125F Disc Abrasive Flap-127mm Fine $17.31 $19.91JPD125M Disc Abrasive Flap-127mm Medium $17.31 $19.91

ABRASIVE FLAP DISCS

DRILL ACCESSORY KIT 4PC 6.3 HEX SPINDLE SET

WIRE BRUSH WITH SCRAPER STAINLESS STEEL 3 ROW3 x 19 rows steel bristles, 360mm long.Solvent proof, hardened and ground steel scraper.

$1081$12.43 GST Incl.

+GST

$1004$11.55 GST Incl.

+GST$900

$10.35 GST Incl.+GST

Code Description +GST Inclusive69957301230 Flap Wheel P60 30x30mm-6mm spindle $4.36 $5.0169957301231 Flap Wheel P80 30x30mm-6mm spindle $4.36 $5.0169957301232 Flap Wheel P120 30x30mm-6mm spindle $4.36 $5.0166623321506 Flap Wheel P60 40x20mm-6mm spindle $5.22 $6.0066623321507 Flap Wheel P80 40x20mm-6mm spindle $5.22 $6.0066623321508 Flap Wheel P120 40x20mm-6mm spindle $5.22 $6.0066623321515 Flap Wheel P60 50x30mm-6mm spindle $6.57 $7.5566623321516 Flap Wheel P80 50x30mm-6mm spindle $6.57 $7.5566623321517 Flap Wheel P120 50x30mm-6mm spindle $6.57 $7.5566623321525 Flap Wheel P60 60x30mm-6mm spindle $7.70 $8.8666623321526 Flap Wheel P80 60x30mm-6mm spindle $7.70 $8.8666623321527 Flap Wheel P120 60x30mm-6mm spindle $7.70 $8.86

FLAP WHEELSNew generation of premium aluminium oxide grain provides an aggressive cut yet long product life. A universal product which achieves a good finish on steel and stainless steel. Excellent cut rate even at low-pressure when used for finishing operations. Conforms to the work piece thanks to the flexible cotton backing .

NORLINE FLAPDISCSFor use with Angle Grinders. Made using premium Zirconia grain. Suitable for light to medium grinding and finishing of steel, Stainless Steel, aluminium, cast iron and wood. Ideal for rust removal, surface preparation, deburring and blending.

Code Description +GST Inclusive77696088184 125 x 22 Flapdisc Norline 40G $4.39 $5.0577696088185 125 x 22 Flapdisc Norline 60G $4.39 $5.0577696088186 125 x 22 Flapdisc Norline 80G $4.39 $5.0563642580356 125 x 22 Flapdisc Norline 120G $4.39 $5.05

HANDY ROLLS 40MM x 50MHigh flexibility for sanding contoured components. Tears easily from handy roll. Suitable for maintenance and general engineering use.

Code Description +GST Inclusive

66623320798 40mm x 50M (P40) $47.44 $54.56

66623320797 40mm x 50M (P60) $43.62 $50.16

66623320803 40mm x 50M (P80) $41.02 $47.17

66623320810 40mm x 50M (P120) $40.12 $46.14

125 X 3 X 22 D/C DISC66252841801

Light weld grinding & polishing of Stainless SteelExcellent performance and finish.

$325$3.74 GST Incl.

+GST

ULTRA THIN CUT OFF WHEELS66253371090

Iron, sulphur & chlorine free. Suitable for structural & all food grade stainless steel. Low noise, low dust, minimal vibration. Fast precise burr free cutting with low energy consumption. Premium grade inox cutting disk. 125x1.0x22.23mm Mega Inox Ultra Thin Cut Off Wheel 25 pack.

$4664$53.64 GST Incl.

+GST

6

BRUSH CUPS & WHEELS

Code Description +GST Inclusive153M Brush Cup CR 75XMT 0.30mm M10/M14 $26.91 $30.95102B Brush Wheel CR 150X19XMB 0.35mm $24.50 $28.17103A Brush Wheel CR 200X19XMB 0.35mm $17.22 $19.80166BM Brush Cup TK18 75X1RXMT 0.50mm $20.77 $23.89166BMSS Brush Cup TK18 75X1RXMT 0.50mm Stainless 316 $43.33 $49.83166M Brush Cup TK18 75X1RXMT 0.35Mmm $20.91 $24.05

Code Size +GST InclusiveTB100M TK20 100X1RXMT 0.50mm $19.60 $22.54TB100MSS TK20 100X1RXMT 0.50mm Stainless 316 $50.43 $57.99TB1153 TK24 115X1RXM14 0.50mm $20.76 $23.87TB1503 TK30 150X1RXM14 0.50mm $51.97 $59.77

BEVEL BRUSHES

4R LONG HANDLE HAND BRUSHES

Code Description +GST Inclusive402 Brush Hand 4R Steel Plastic Handle $7.70 $8.86422 Brush Hand 4R Stainless Plastic Handle $12.13 $13.95442 Brush Hand 4R Brass Plastic Long Handle $13.50 $15.52

Code Size +GST InclusiveBLH3R Brush Hand 3R Wood Long Handle $3.75 $4.31BLH4R Brush Hand 4R Wood Long Handle $4.27 $4.91BLH4RB Brush Hand 4R Brass Wood Long Handle $8.57 $9.86BLH4RSS Brush Hand 4R Stainless Wood Long Handle $7.10 $8.17

BRUSH HAND LONG HANDLE

Code Size +GST InclusiveBSBB Brush Hand CR Brass Orange Plastic Handle $8.22 $9.45BSBS Brush Hand CR Steel Red Plastic Handle $5.51 $6.34BSBSS Brush Hand CR Stainless Green Plastic Handle $8.22 $9.45

BRUSH HAND PLASTIC HANDLE

Code Size +GST InclusiveJTS012L Tapered Spindle M12 x 1.75 Left Hand Thread $13.46 $15.48JTS016L Tapered Spindle M16 x 2.00 Left Hand Thread $16.44 $18.91JTS120L Tapered Spindle 1/2" Left Hand $13.30 $15.29JTS580L Tapered Spindle 5/8" Left Hand $16.15 $18.57

TAPERED SPINDLES AND DRILL ACCESSORY KIT

BRUSH HAND HOT BENCH WOOD LARGE HANDLEJHBHBL

BRUSH WHEEL PIPELINE TK60 178X1RX22 0.50MMJS8020

POLISHING MUSHROOM 75 CALICO 6.3 SPINDLEBCM75

BRUSH HAND 3R 180X10 STAINLESS SMALL PLASTIC HANDLEPH3RSS

$1244$14.31 GST Incl.

+GST

$6154$70.77 GST Incl.

+GST

$1222$14.05 GST Incl.

+GST

$1642$18.88 GST Incl.

+GST

Code Size +GST InclusiveJLL15050 Polishing Wheel 150x15 50 Fold Calico Loose Leaf $11.91 $13.70JLL20050 Polishing Wheel 200x15 50 Fold Calico Loose Leaf $20.60 $23.69

POLISHING WHEELS

Code Size +GST InclusiveJPK1 Polishing Kit 50 4pce 6.3 Hex Spindle $11.94 $13.73JPK2 Polishing Kit 50 & 100 6pce 6.3 Hex Spindle $22.84 $26.27JRPK100 Polishing Wheel 100 2pce Kit 6.3 Hex Spindle $10.13 $11.65JRPK50 Polishing Wheel 50 2pce Kit 6.3 Hex Spindle $5.46 $6.28

POLISHING KITS AND WHEELS

7

$14143$162.64 GST Incl.

+GST

$8146$93.68 GST Incl.

+GST$16108$185.24 GST Incl.

+GST

$8609$99.00 GST Incl.

+GST

SPIRAL FLUTE STEP DRILL SET 3PCBL234-S1

Contains: 4 - 12, 4 - 20, 4 - 30mm. 5mm step depths with engraved depth guide. M2 High Speed Steel.

SPADE BIT SET 20, 22 & 25MM - 3PC SET

BL237-S1

$1836$21.11 GST Incl.

+GST

DRILL SET 25PCBL-M3

Trade quality. 118° split point. HSS.

2015-M2 DELTA M2 DRILL SET (19PCE) 1-10mm

2015-M3 DELTA M2 DRILL SET (25PCE) 1-13mm

DELTA M2 DRILL SETDelta Point drill bits drill twice as fast as conventional split point drills and drill up to 10 times more holes per bit. -Their unique point geometry simplifies point location when drilling on curved or uneven surfaces.

$6000$69.00 GST Incl.

+GST

SCREW EXTRACTOR SET 10PC C/W DRILLS9900-SM2

Set contains 5 x screw extractors: No.1 - No.5 and 5 x left hand drills to suit.Surface finish: Bright. Material: Chrome alloy. Drill: Extractor and LH Stub drill. Packaging: Plastic case. Pack quantity: 10pc. Sizes: 1-5.

BONUSJunior

Hacksaw

$3043$35.00 GST Incl.

+GST

$13457$154.75 GST Incl.

+GST

$2983$34.31 GST Incl.

+GST

$2500$28.75 GST Incl.

+GST

$4500$51.74 GST Incl.

+GST

$2700$31.05 GST Incl.

+GST

$15496$178.20 GST Incl.

+GST

HACKSAW225-PLUS

Sutton Tools Impact Bi-Metal Holesaws are designed for use in impact drivers. Suited to cut sheet metal up to 3mm maximum thickness. Ideal for electrical installation, junction boxes, ducting and general sheet fabrication.

$174 EA$2.00 EA GST Incl.

+GST

HACKSAW BLADES, SANDFLEXVirtually unbreakable and shatterproof Bi-Metal Hacksaw Blade. The Sandflex Blade combine extreme cutting with a high degree of flexibility.

3906-300-18-100 - 18TPI3906-300-24-100 - 24TPI3906-300-32-100 - 32TPI

7 PC BI-METAL IMPACT HOLESAW SET H119S7

1/4” Hex shank suitable for impact drivers. Ejector spring quickly ejects waste material. Thin wall 8 TPI for fast and burr free cutting. Stop Shoulder to prevent over drilling. Bi-Metal HSS premium quality for toughness and longer life.

CARBIDE BUR SET SCB-5AB901SCB5A

The double cut bur allows for rapid stock removal in harder materials. 6mm shank. Contents: 9.5mm Cylindrical Square, Cylindrical Radius, Tree, 12.7mm Cylindrical Square, Cylindrical Radius.

11PC MULTI-TOOL HANDLE SETH5940003

Multi-Tool Handle. 150mm Reciprocating Blades: Wood Cutting 10TPI, Metal Cutting 24TPI. 25mm Screwdriver Bits: PH1, PH2, PH3, SL4.5, SL7, PZ1, PZ2, 100mm Extension.

HSS SPRINT MASTER DRILL SET 6 PCDRIS-811-TM6

High performance HSS jobber drill set.Contains drill sizes Ø 2.0, 3.0, 4.0, 5.0, 6.0, 8.0mm.Made in Austria.

MULTICUT DRILL SET 5 PCDRIM-100-PM5

Precision cutting, multi-purpose drilling solution, for a variety of materials including steels, plastics, masonary and tiles.Contains drill sizes Ø 4.0, 5.0, 6.0, 8.0, 10.0mm.Made in Austria.

LONG LIFE CONCRETE AND MASONARY DRILL SET 8 PCDRIM-700-TSS3

General purpose "Long Life" masonary drill for percussion and rotary drilling in concrete, brick and natural stone.Contains drills sizes Ø 3.0 to 10.0mm.Made in Austria.

Sizes: 19, 22, 25, 29, 32, 35, 38mm• 1/4" Hex shank suitable for impact drivers.• Ejector spring quickly ejects waste material.• Thin wall 8 TPI for fast and burr free cutting.• Stop shoulder to prevent over drilling.

8

Universal BlueGasket & Jointing Compound

The leading non-setting gasket & jointing compound available today.The product can be used to replace a traditional gasket or to “dress”it to significantly improve the performance of the gasket.

• Non-hardening, non-setting• Wide operating temperature range (-50 to +250ºC)• Fuel resistant

UNIVERSAL BLUEIN ACTION

AUTOSOL POLISH World famous winner of international awards. Brilliant high gloss finish. Cleans, shines & protects. For all metal surface types.

Code Size +GST InclusivePOLM Autosol Polish 100gm Tube $7.46 $8.58POLM-01 Autosol Polish 1kg 750ml $52.23 $60.07POLM-1140 Autosol Polish (4kg) 3Ltr Tub $237.31 $272.91

POLISH 265ML TUB C/W SCOURER SPONGEPOLM-1035Famous Metal Polish quality.Re-sealable plastic tub for convenient storage.Scourer sponge for reliable application.

$3134$36.04 GST Incl.

+GST

UNIVERSAL BLUE GASKET & JOINTING COMPOUND - 100GMHYLO-100 Non-setting, non-hardening sealant even at high temperatures up to 250 degrees Celsius.Resistant to a wide range of fluids including all industrial fuels, oils, water and brine.

20004 RUST REMOVER & PREVENTION 30ML WITH BRUSHCONR-003Effectively removes surface rust.Chemically bonds to the metal surface, providing a long lasting rust prevention treatment.Larger spray-bottles also available.

ADBLUEModern diesel engines employing the latest Diesel Exhaust Fluid (DEF) emissions control technology deserve the best quality urea additive to ensure reliability and compliance with vehicle warranty standards. Genuine AdBlue™ is the accepted standard for meeting quality requirements.

HYLOMAR AEROSOL 200MLHYLO-200The original and genuine non-setting gasket and jointing compound, now in a convenient aerosol.Dichloromethane free.Wide operating temperature range (-50 to +250ºC).

$2239$25.75 GST Incl.

+GST

$1250$14.38 GST Incl.

+GST

$1717$19.74 GST Incl.

+GST$1897


$1179$13.56 GST Incl.

+GST

$3761$43.25 GST Incl.

+GST

MQR0084 10 LITRES

MQR0085 4 LITRES

WD-40 EZ REACH 425GWD61180A breakthrough in getting WD-40® Multi-Use Product where you need it. EZ-REACH is equipped with an attached flexible straw that bends and keeps it shape, giving you unlimited access to hard-to-reach jobs. This trusted and proven problem solver has so many uses and works so effectively. It is essential in any maintenance environment.

•19 cm flexible straw •Straw bends and keeps its shape •Sprays 2 ways

BONUSBuy 1 can of WD-40

and get a tube of Hand Repair

My PAINTINGMY paintingAt an art gallery, a woman and her ten-year-old son were having a tough time choosing between one of my paintings and another artist’s work. They finally went with mine.“I guess you decided you prefer an autumn scene to a floral,” I said.“No,” said the boy. “Your painting’s wider, so it’ll cover three holes in our wall.”

9

of coke NO SUGAR with every 6 pack

of CRC brakleenor Brakleen

Blaster

8 free canS

*8 cans of Coke No Sugar with every specially marked pack of Brakleen or Brakleen Blaster only. Stock released: 20th January 2020. Ordering: 1 pack = 6 cans of Brakleen or Brakleen Blaster. Offer valid until stocks last.

Code Size +GST Incl.

17089 32 oz $18.30 $21.04

17090 1 Gal $29.98 $34.48

17091 5 Gal $148.85 $171.18

WELD-KLEEN 350 Anti-Spatter

WELD-KLEEN HD Anti-Spatter

CDT Cutting Range

A safe, effective water-based Anti-Spatter for use on most base metal applications. Non-hazardous formula is bio-based and paintable.

WELD-KLEEN HD® Anti-Spatter is a heavy duty base metal treatment that is solvent based and quick drying. Accepts pre-heating. The Non-flammable and paintable spray is ideal for protecting parts, clamps, tooling and fixtures.


17030 20 oz $13.77 $15.83

TAC-2 Food Grade CO Contact Cleaner

An evaporating precision cleaner designed to remove light contaminants from electrical and electronic equipment in the food industry. MPI & NZ AsureQuality approved.

An exceptional general purpose lu-bricant with tough adhesive qualities. Based on heavy-duty high-pressure gear oil and modified to resist fling-off at high speed and high temperatures.


5035 400ml $16.82 $19.34


3102 400ml $231.36 $24.56

Contact your Local tradezone branch to have a crc expert REVIEW AND ADVISE ON your parts washing needs.

• Exceeds current legislation for health & safety• Exceeds environmental standards and reduces waste• Reduces risk - future & present• Excellent cleaning ability• Non-toxic, Non-hazardous & Non-irritating

BE SAFE, BE SMART.

PROTECT YOUR TEAM & THE ENVIRONMENT

SMARTWASHER START UP KIT

FREEWEBER Q1000 BBQ WITH ANY

PURCHASED BETWEEN

Superior neat cutting, drilling tapping, and reaming lubricants, formulated for hand and machine cutting on all types of metal.

Type Code Size +GST Incl.

Aerosol 3063 400ml $18.73 $21.45

Liquid 3064 500ml $26.79 $30.81

Liquid 3068 5 L $169.73 $195.19

3/2/20 - 27/3/20

Code Description +GST Incl.

508761 CRC Brakleen Blaster 6 Pack with Coke No Sugar $51.18 $58.86

508961 CRC Brakleen 6 Pack with Coke No Sugar $51.18 $58.86

10

4.0T 2-POST HYDRAULIC FLOOR BASE HOISTAA40FB2P

• Lifting capacity of 4,000kg• Lifting height of 1,900mm• Minimum height of 100mm• Inside column height of 2,824mm• Post height of 2,826mm• Lifting time of 55 seconds

• 115% dynamic loading and 150% static loading test

• P54ABS control box and 24V operating button

• Electrical single release• 2.2kW aluminium motor.

MOBILGREASE CMP

MOBIL DELVAC MX ESP 15W-40 (20LT)

MOBIL NUTO H46 (20LT)

MOBILGREASE XHP 222 (16KG)

• Mobil CM-P Grease benefits include, Extra high performance extreme-pressure greases

• Excellent resistance to water, including water

• Very good EP and anti-wear protection• Resists rust and corrosion• Good pumpability at low temperatures

• Extra high performance diesel engine oil• Outstanding performance in modern

high output low emission engines including those with exhaust gas recirculation and diesel particulate filters.

• Mobilgrease XHP 222 greases are extended service lithium complex greases

• Superb resistance to water washout and spray-off

• Highly adhesive and cohesive structure• Excellent rust and corrosion resistance.

140709

$127.99 Inc GST140141

121284 I000110

$10.49 Inc GST

I000106

• Nuto H Series oils are good quality anti-wear hydraulic oils intended for industrial and mobile service applications

• Good anti-wear performance helps reduce pump wear and prolonging pump life

• Corrosion protection helps reduce the effects of moisture on system components

• Filterability to prevent filter blockage even in the presence of water

20KG GREASE KIT424170

Integral filter protects pump from foreign particle contamination. Delivery rates of up to 0.9 kg/min. 55:1 ratio air motor develops grease pressures of up to 7,950psi (548bar). Will handle high density, tacky greases up to NLGI2. Cast alloy dual cylinder air motor won’t dent or distort prematurely. Ergonomic grease control valve is easy and comfortable to operate, convenient carry handle assists in kit portability and helps address OH&S issues, and operator friendly. Easily adjustable bung adaptor enables the kit to be used on a variety of drum sizes and types. Single toggle air motor operation ensures a long service life. Heavy duty 3 jaw coupler ensures a tight and precise grease nipple connection.

$86190$991.19 GST Incl.

+GST

$41912$481.99 GST Incl.

+GST

$10859$124.88 GST Incl.

+GST

TRIGGER ACTION GREASE GUN 450GM660AN

Grease pressures of up to 8,500psi (586bar). Delivers up to 1.1g of grease per stroke. Coarse thread on barrel assembly eliminates cross threading during cartridge changeover. High volume or high pressure option facilitates fast and efficient greasing. 4 jaw coupler and flexible 30cm long extension. Manufactured in Germany.

18V LI-ION BATTERY GREASE GUNARG2235

• Cordless, battery powered grease gun• 18V Lithium Ion battery• Suits 450gram cartridges• Develops up to 10,000psi• 75gram per minute volume grease flow

• 1 hour quick change• Shoulder strap• Three-way loading - cartridge,

bulk grease or filler pump• 2 x 18V Lithium Ion batteries included• 1m heavy duty high pressure hose• Up to 5 cartridges of grease on a single

charge of the battery• Heavy duty plastic storage case

$7313$84.10 GST Incl.

+GST$8507


PREMIUM LEVER ACTION GREASE GUN 450GMARG2555 Develops up to 12,000psi. Thick piston for greater volume. Coarse thread to stop cross threading.

PREMIUM TRIGGER ACTION GREASE GUN, 450GM

ARG2666

Develops up to 12,000psi. Suitable for use with

450gram cartridges or bulk grease.

EA

$21739$250.00 GST Incl.

+GST$11130$127.99 GST Incl.

+GST

$7826$90.00 GST Incl.

+GST


+GST


+GST

16KG 450gm

$4,37500$5,031.25 GST Incl.

+GST

11

$37313$429.10 GST Incl.

+GST

ELECTRONIC LEVEL 600MMST196-2-E-600

Features 2 digital displays on the front and top of the level. This level features: 4 modes: degrees, percentage, mm/m and in/ft. Approximately 150 hours of operation.

$1,43750$1,653.13 GST Incl.

+GST

OPTICAL DUMPY LEVELST17862Easy to read and reliable transfer of heights. 26x magnification in the optical system. Robust protection for the optical system also in the front of the instrument. Easily accessible focussing and adjusting screws. Protection class IP 54.

ELECTRONIC ANGLE FINDERSTTECH-700DAOne tool – three functions: digital electronic angle finder, spirit level and bevel gauge. Accurate angle determination in the range from 0° – 270°. Digital display that can be read easily and illuminated. Two high-quality vials which can be read in all positions. LOCK function for transferring angles reliably.

TRADE LEVEL 2440MMST96-2-2440• Ultra rigid aluminium profile with reinforcing. • High-precision measuring in all positions • Removeable, shock-absorbing end caps with

anti-slip stopper

POCKET LEVEL PROST17953Direct alignment of switches & Sockets. Rare-Earth magnet system. Original large size Stabila precision vial

LASER DISTANCE MEASURER LD250 BTST18817Bluetooth® Smart 4.0 for direct data transmission. Free app: STABILA Measures. Easy to use. Rapid measuring results. The large digits and display lighting make it very easy to read.

CROSS LINE LASER LAX300STL19033Green laser lines and plumb-line dots for optimum visibility. Laser lines are especially bright and sharp to ensure accuracy whilst working.For levelling work at a distance of up to 30m. Compact rotatable housing with extendable foot for height adjustment.

SELF LEVELLING LASER LEVELSTL17658No waiting time – quick self-levelling function thanks to pendulum technology. Versatile – 7 laser functions to support many of the measuring methods used on a construction site. Easy operation with a two-button system.

$399 13$459.00 GST Incl.

+GST

$355 23$408.51 GST Incl.

+GST

$208 96$240.30 GST Incl.

+GST

$26 71$30.72 GST Incl.

+GST

$6642$76.38 GST Incl.

+GST

$250 75$288.36 GST Incl.

+GST

$58750$675.63 GST Incl.

+GST

Taking precise measurements is one of the most important tasks on construction sites, which is why it is crucial that professionals have tools that they can rely on at all times. Tools that enable them to carry out a variety of measurement tasks on the construction site precisely, efficiently and easily – time after time. Tools that deliver reliable results in all weathers, even under the toughest conditions, so mistakes are avoided and there is no need for expensive, time-consuming reworking further down the line. Tools that make work easier and boost productivity. STABILA provides you with tools that meet your exacting standards.

The best quality will prove its worth. Sooner or later. Every craftsman knows that not everything runs smoothly on the construction site. How good it is then when you can rely on the fact that your tools will not let you down when you need them. Just imagine: your spirit level falls from the scaffold and, after a hard bang, it works just as accurately as it did on the first day. That is STABILA quality! STABILA spirit levels are constructed with a fixed moulded vial which measures absolutely accurately even under demanding conditions – no readjustment necessary. For this reason craftsmen worldwide trust our spirit levels. At STABILA, every craftsman finds the right spirit level: depending on the requirements and application needs – light or tough, short or long, up to and including special spirit levels which are intended completely for one trade.

GOOD TOOLS GOOD WORKGOOD TOOLS GOOD WORK

SCAFFOLDERS LEVEL 250MMST81SM-250

250mm long with magnets in base. Milled working face. Pressure die-cast light alloy body. Highly shock absorbent.

12

$2278$26.20 GST Incl.

+GST

$2164$24.89 GST Incl.

+GST$3850


$7164$82.39 GST Incl.

+GST

KOMELON FOLDING RULE (FD1M)FD1M High quality industrial measuring tapes.

TAPE MEASURESAll metallic components are stainless steel for rust resistance. Class II accuracy printed blade, controlled by precise equipment. Nylon coated blade for maximum durability.

Code Description +GST InclusiveTA3360 Tape Measure 8M x 32mm $38.09 $43.80TA3380 Stainless Steel Tape 8m "Gripper" $34.33 $39.48TA3785 Tape Measure Auto Lock 8mt $11.29 $12.98TA3821 2m X 13mm Powerblade Measuring Tape (packed 20 in a jar) $7.86ea $9.04ea

M720 Blu-Mol Plastic Electronic Vernier 150mm/6"

M780 Blu-Mol Elect. Large Screen Vernier 150mm/6"

LARGE SCREEN VERNIERR302V Free With M780

PROTRACTOR - 180° 301955 For accurate angle, depth and length measurements. 180° along with 100mm rule. Photographically etched markings for ultimate precision and accuracy.

BONUSFree Chalkholder with every pack of chalk -

chalk must be purchased in carton lot (12 pack)

$2850$32.78 GST Incl.

+GST$6435


ENGINEERS CHALKC302 144pcs per pkt. 100mm long x 12mm x 5mm. Can be used in chalk holder - optional extra.

ENGINEERS BLACK BOOKL100V3EN• Pocket sized • Grease / Tear proof • Lay- Flat Format • Bonus Sticker Tabs

CLOTH TAPEStrong and versatile yet easy to tear by hand. Limitless uses for repairing, binding, bundling, sealing, insulating and reinforcing.


66623336613 Black Cloth Tape 50mm x 25m Roll $7.56 $8.69

66623336616 Silver Cloth Tape 50mm x 25m Roll $7.56 $8.69

CASTORS

LIFT TABLESLR003500kg


R4045 Medium Duty Castor Fixed 200kg $15.67 $18.02

S4044 Medium Duty Castor Swivel 200kg $18.21 $20.94

S4044B Medium Duty Castor Swivel Brake 200kg $22.09 $25.40

$6717$77.24 GST Incl.

+GST$60696$698.00 GST Incl.

+GST

$5671$65.22 GST Incl.

+GST

AL-KO MULTIFIT COUPLING614800Automatically engages and locks, >low Profile, 2500kg capacity

AL-KO PREMIUM JOCKEY WHEEL626200Zinc plated finish,400Kg capacity,150mm solid wheel

SPEND $100 EXCL.GST ON BAHCO FILES

DURING CALIPER V172AND RECEIVE A FREE PIZZA VOUCHER

• ERGONOMIC HANDLE • FULL RANGE AVAILABLE • MADE IN PORTUGAL

13

Code Description +GST InclusiveE300645000 Energizer Vision HD+ Focus Headlight $39.13 $45.00E300655000 Energizer Vision Metal HD 6AA $43.47 $49.99E300655200 Energizer Vision Metal HD 2AA $26.08 $29.99E301360700 Energizer LED Metal Light $7.82 $8.99

$8209$94.40 GST Incl.

+GST

$1999$22.99 GST Incl.

+GST

$17217$197.99 GST Incl.

+GST

$9504$109.30 GST Incl.

+GST$19700$226.55 GST Incl.

+GST

$12365$142.20 GST Incl.

+GST

$10997$126.47 GST Incl.

+GST

GEARWRENCH MULTI PURPOSE FLEX LED LIGHT831333 lighting options, spotlight, 50% brightness and 100% brightnessSuper bright 380 lumensMagnets on rear and also on baseLight can be rotated 150 degrees360 degree swivel hook.

ENERGIZER MAX AA 20PKE301024100

MAGNETIC RECHARGEABLE L.E.D WORKSHOP LAMP71228Allows handsfree illumination, ideal for mounting on hoits, hoist arms, toolboxes and other workshop surfaces, 2x 5W COB LED's provide 6000k of bright white light, selectable light output 350 lumens at 15

ALS RECHARGEABLE L.E.D INSPECTION LIGHT - 200 LUMENS71460200 lumen inspection light at 2.5 hours use, 100 lumen torch function, 2-3 hour charge time, 180 degree rotating bracket with powerful magnet, 360 degree swivel hook, glow in the dark locator, charge via USB lead

ALS RECHARGEABLE RANGE FINDER & L.E.D LIGHT - 250 LUMENS71490250 lumen inspection light, range finder up to 60 meters, unit conversion between imperial & metric, 2.5 hours at peak output or 4 hours at low output, 120 lume torch function, charge via USB lead

250LM DETACHABLE LED HEAD LAMP71426250 lumen 120 degree angle flood beam, high powered 150 lumen spotlight and 60 meter distance, motion sensor activated, 3 hours use, glow in the dark locator, magnetised detachable lamp allows lamp to be used seperately.

HOT DEVIL TRADE MAP TURBO TORCH KITHD030Hot Devil Turbo Torch Kits are suitable for soldering copper pipes, loosening rusted fasteners & brazing copper pipes. The turbo nozzle creates a swirl action flame, this swirl action heats 40% faster. The torch can swivel 360 degrees & features auto ignition.

Includes: 1x Turbo Torch 1x MAP Gas Cylinder 3 Years Warranty On Torch"

hours or 750 lumens at 6 hours, 90 degree hinge joint, powerful magnet allows mountng to any surface.

ENERGIZER VISION HD + FOCUS HEADLIGHT

Code Description +GST Inclusive300600 LED Pocket Pen Light $41.83 $48.11300601 LED Inspection Light $89.03 $102.38300602 LED Slimlight $106.31 $122.26

LED LIGHTS• Bright and robust pocket

pen light for quick and easy illumination of dark work areas

• Lighting modes: Bottom Light with direct beam and Work Light

with wide flood beam• Inbuilt belt clip with magnet• High impact ABS plastic

housing with impact resistant polycarbonate lens

SOLDERING IRONSComes with solder stands.

PORTABLE SOLAR CHARGER• Portable solar charger • 12V, 1 Amp solar maintenance charger • 5V, 2.1 Amp USB charger • Lightweight • Compact • Water-resistant • Includes USB and 12V charging cables! • Zippered pouch for cable storage.

Code Description +GST Inclusive302102 Soldering Iron 60w c/w Bench Stand $25.27 $29.06302103 Soldering Iron 80w c/w Bench Stand $26.82 $30.84302104 Soldering Iron 100w c/w Bench Stand $38.04 $43.75

3 LED TELESCOPING PICK UP TOOLTL66011

3 x ultra-bright LEDs. 2 magnets at end of lamp. Flexible neck: 17.5 - 57cm. Aluminium body. 2 x batteries: Lr44

TMTM

TM

TM


+GST

Code Description +GST InclusiveMA1103 Portable Solar Charger 12V/5V 14 Watt $231.94 $266.73MA1104 Portable USB Solar Charger 15 Watt $181.19 $208.37MA1105 Portable USB Solar Charger 5 Watt $100.44 $115.51

14

Power Supply 230v - 1Ph Duty Cycle @ 40°C 10% @ 185A @ 25°C 40% @ 185A Amp Range MIG 30 - 185AAmp Range TIG/MMA 10 - 130ARated Power 5.7KVAWeight 13.5KgCertification Approval AS/NZ 60974-1

VIPER MIG185185 AMP MIG/TIG/MMA

$949.00 GST Incl.

$ 82522C/w 3m XA15 Suregrip™ BZL Series Mig Torch, Arc Set x 3m, Twin Gauge Argon Regulator. Tig Torch is Optional and Extra

• MIG Gas/Gasless• Digital Meters • Spool Gun Ready • 5Kg Spool Capacity • Burn Back Control• DC Lift Arc TIG • Hot Start Electrode

XA-MIG185V-SP

230V 10A

MIG185

VIPER CUT30 PLASMA CUTTER30 AMP CLEAN CUT 12MM STEEL

C/w SureCut™ SC40 Plasma Torch x 4m, Earth Lead and Spares Kit

Power Supply 230v - 1PhDuty Cycle @ 40°C 15% @ 30A @ 25°C 30% @ 30ACurrent Range 20 - 30A Cutting Thickness - Clean 12mm Steel Cutting Thickness - Sever 14mm Steel Air Flow Draw 6.0 cfm Air Pressure 70psi Dimensions (mm) 460x160x320Weight 11.6kgCertification Approval AS/NZ 60974-1

• Modern IGBT Technology • Pilot Arc Non Contact Start • 12mm Clean Cut on Steel • Contact Start Capable• Drag Cutting Capable • High Quality Surecut SC40 Torch• Pre-set Air with Auto Drain • Generator Compatible 7.5KVA

XA-CUT30V-K

$795.00 GST Incl.

$ 69130

230V 10A

CUT3O

BONUSAuto Helmet

VIPER ARC140140 AMP - 230 VOLT MMA DC WELDER

Power Supply 230v - 1Ph Duty Cycle @ 40°C 15% @ 140A @ 25°C 40% @ 140A Current Range 20 - 140ARated Power 6.5KVAWeight 3.8KgCertification Approval AS/NZ 60974-1

XA-VA140 $269.00 GST Incl.

$23391

C/w 2.5m Arc Lead Set

• DC Stick Electrode • Scratch Start TIG • 20-140 Amps • Generator Compatible• Electrode Hot Start • Lightweight & Portable

ARC14O

230V 10A

Razorweld MIG25ODRZ

250AMP MIG/TIG/MMARAZORWELD MIG250DRZ

• MIG Gas/Gasless 15Kg Spool• Soft Start - Burn Back - Wire Inch • Spool Gun Connection• DC TIG, Lift Arc ignition• TIG Down Slope & Post Gas• MMA function (Stick electrode) • VRD - Hot Start - Arc Force

Power Supply 230v - 1PhDuty Cycle @ 40°C 40% @ 250ADuty Cycle @ 25°C 60% @ 250ARated Power MIG 11.0KVA Current Range MIG 30 - 250ACurrent Range MMA-TIG 10 - 250A Dimensions (mm) 585x280x440Weight 35.0Kg

$2,395.00 GST Incl.

$ 2,08261C/w 4m Digital Control Mig Torch, Arc Set, Flowgauge Regulator,XA26FX Euro Tig Torch Kit

XA-MIG250DRZ-SP

Digital Control MIG Torch

MIG35OSWF

• 4 Roll Separate Wire Feeder • 10m Interconnecting Cables • MIG Inductance & Burn Back Control• MIG Crater Current Control • 2T/4T Trigger Function• MMA Arc Force Control• DC TIG Lift Arc Function • Approved to AS/NZ 60974-1• Heavy Duty Trolley, Cylinder Rack

Adjustment of Voltage & Wire Feed at the Wire Feeder makes for easy setting of the welding parameters with the convenience of remote adjustment from the power source.

C/w 4m Mig Torch, Arc Set and Regulator Tig Torch is Optional & Extra.

350 AMP MIG-TIG-MMA WELDERSEPARATE 4-ROLL WIRE FEEDER

RAZORWELD MIG350SWF

XA-MIG350SWF-K

$4,999.00 GST Incl.

$4,346 96

Power Supply 415V - 3 PhaseDuty Cycle @ 40°C 40% @ 350A Current Range MIG 50 - 350A Current Range MMA 20 - 350A

Euro Connection

COMBOEuro Tig Torch Kit

RAZORWELD MIG200WRZ200AMP - 230V MIG-TIG-MMA WELDERPUSH-PULL & SPOOL GUN READY• MIG Gas/Gasless, 15kg Spool Capacity• Burn Back Control• Variable Inductance Control• Wire Inch• Spool Gun Ready • Inbuilt Cylinder Rack • DC TIG - Lift Arc Ignition• MMA Electrode Hot Start

Power Supply 230v - 1PhDuty Cycle @ 40°C 15% @ 200A @ 25°C 40% @ 200A Current Range MIG 30 - 200ACurrent Range MMA 10 - 200A Size (mm) 900x400x785Weight 57.0Kg

C/w 4m Mig Torch, Arc Set & Regulator. Tig Torch is Optional & Extra $1,899.00 GST Incl.

$1,65130

XA-MIG200WRZ-K

Razorweld MIG2OOWRZ

Razorweld

15

AS6000F AUTOMATIC HELMETLARGE VIEWING AREA

$149.00 GST Incl.

$ 12957AS6000F

TRUECOLOUR LENS• MIG/MMA/TIG Compatible• Battery & Solar Powered • Replaceable Batteries• Large Viewing Area - 100mm x 60mm• Four Independent Sensors• Grind Mode Function• Variable Shade 4/9~13• Adjustable Sensitivity & Delay Controls• Fast Switching Speed 0.08 m/s• Compliant to AS/NZS 1338.1

XA-5011 ADF Analog Control Panel

XA-10-2015L Large Pair XA-10-2015XL X-Large Pair XA-10-2015L-LH Lefties Large PairXA-10-2015XL-LH Lefties X-Large Pair

Code Descr ip t ion +GST Inc lus ive

ESR1125-25P 6013GP E lec t rode 2.5mm 2.5kg P las t i c Can is te r $24.00 $27.60




STAINLESS STEEL• All Position• Stable Arc with Minimal Spatter

Code Desc r ip t ion +GST INCLEI316L20-175 316L E lec t rode 2.0mm 1.75kg Vac Pkt $68.50 $78.78EI316L25-175 316L E lec t rode 2.5mm 1.75kg Vac Pkt $68.50 $78.78EI316L32-20 316L E lec t rode 3.2mm 2.0kg Vac Pkt $68.00 $78.20EI316L40-20 316L E lec t rode 4.0mm 2.0kg Vac Pkt $70.00 $80.50

EI316LFor welding molybdenum bearing 316 & 316L austenitic stainless steels. Low carbon level eliminates carbide precipatation.AWS/ASME SFA 5.4 E316L-16

HIGH QUALITY WELDING ELECTRODESFULL INTERNATIONAL APPROVALS

• Easy Slag Removal• Fine Ripple Read Appearance

Code Desc r ip t ion +GST INCLEI312L25-175 312L E lec t rode 2.5mm 1.75kg Vac Pkt $71.00 $81.65EI312L32-175 312L E lec t rode 3.2mm 1.75kg Vac Pkt $69.00 $79.35EI312L40-20 312L E lec t rode 4.0mm 2.0kg Vac Pkt $80.00 $92.00

EI312LFor joining hard to weld metals, dissimilar metals, high strength welds. Good wear resistance.AWS/ASME SFA 5.4 E312-16

LOW HYDROGEN IRON POWDER• All Position and Easy Slag Removal• Stable Arc with Minimal Spatter

Code Desc r ip t ion +GST INCLESB4825-25V 7018-H8 E lec t rode 2.5 x 350mm 2.5Kg Vac Pkt $26.00 $29.90ESB4832-25V 7018-H8 E lec t rode 3.2 x 350mm 2.5Kg Vac Pkt $26.00 $29.90ESB4840-25V 7018-H8 E lec t rode 4.0 x 450mm 2.5Kg Vac Pkt $26.00 $29.90

ESB48Smooth running with clear molten pool, excellent re-strike, superb weldability with excellent bead appearance.AWS/ASME SFA - 5.1 E 7018 - H8

• Easy to Control Weld Deposition• Good Weld Bead Appearance

DUAL COATED LOW HYDROGEN• All Position and Easy Slag Removal• Stable Arc with Minimal Spatter

Code Desc r ip t ion +GST INCLESB4425-25V E7016-H8 E lec t rode 2.5mm 2.5Kg Vac Pkt $26.00 $29.90ESB4432-25V E7016-H8 E lec t rode 3.2mm 2.5Kg Vac Pkt $26.00 $29.90

ESB44A multi-purpose electrode suitable for structural steelwork, workshop and maintenance welding. The dual coating of this electrode produces a stable, concentrated and directed arc.AWS/ASME SFA - 5.1 E 7016 - H8

• Easy to Control Weld Deposition• Good Weld Bead Appearance

VACUUM PACKAGING • NO RE-BAKE REQUIRED • 100% HERMETICALLY SEALED PACK• ALWAYS FACTORY FRESH, DRY ELECTRODES• SAFE 12HR EXPOSURE TIME AFTER OPENING• REDUCE RISK OF HYDROGEN CRACKING OR POROSITY

TRADESMAN WELDING GLOVES LEFT HAND PAIRS AVAILABLE

These tradesman quality general purpose welding gloves are made of heat and flame-resistant shoulder split cowhide. With a full sock lining for added comfort and Kevlar stitching with welted seams for wear resistance, these gloves are durable, dexterous and comfortable. Ideal for MIG and ARC welding.

$13.50 GST Incl.

$1174

WELDING RESPIRATOR HALF-MASK LOW PROFILE, REPLACEABLE FILTERS

Code Desc r ip t ion +GST INCLXA-MASK-SM E l ipse P2 Weld ing Resp i ra tor Ha l f Mask S ize S/M $77.39 $89.00XA-MASK-ML E l ipse P2 Weld ing Resp i ra tor Ha l f Mask S ize M/L $77.39 $89.00XA-F ILTER-TP Weld ing Fume F i l te r Car t r idge Twin Pack $32.17 $37.00

WELDERS SKULL RAGSFLAME-RETARDANT

Made from 100% pre-shrunk cotton and resistant to flame and welding spatter for up to 50 home washings. Athletic mesh lining for comfort, air cushioned insert for sweat absorbency, ties at the back and one size fits all.

Code Desc r ip t ion +GST INCLXA-23-3615 Xce lArc Heavy Duty Sku l l Rag - B lack $21.70 $24.95XA-23-3613 Xce lArc Heavy Duty Sku l l Rag - Safety Orange $21.70 $24.95XA-23-3602 Xce lArc Sku l l Rag - Wi ld $21.70 $24.95XA-23-3606 Xce lArc Sku l l Rag - Happy Hour $21.70 $24.95XA-23-3601 Xce lArc Sku l l Rag - Camouf lage $21.70 $24.95XA-23-3607 Xce lArc Sku l l Rag - Parad ise $21.70 $24.95

Black

Safety Orange Wild Happy Hour Camoflage Paradise

• Latex and silicone free, lightweight TPE face piece • Comfortable to wear for long periods of time • Low profile filters provide unobstructed field of vision• Compatible with other PPE, including welding helmetsGENERAL PURPOSE

• All Position• Stable Arc with Minimal Spatter

ESR11For all position welding with excellent X-Ray qualities. Excellent also for galvanised, dirty and rusty steels.AWS/ASME SFA - 5.1 E6013

• Easy Slag Removal• Good Weld Bead Appearance

Welding helmet pictured not includedElipse P2 Welding Respirator Half Mask Spare Filter Pack

16


SPITFIRE1125 Air Compressor 25 Ltr $337.13 $387.70SPITFIRE1140 Air Compressor 40 Ltr $396.93 $456.47

AIR COMPRESSORS SPITFIRE1125

25/40 Litre Tank. Easy handling 2.2 HP motor. Cast iron cylinder. Steel Valves. Pressure switch control. Includes filter regulator. Electric motor overload protection. 1 year warranty.

PETROL COMPRESSOR 70 LTR TANKP7065-H• Heavy Duty Cast Iron Slow RPM Pumps • Genuine Condor Pressure Switches • High Quality Powdercoat Finish • Honda GX Petrol Engine Recoil • Two Large Wheels for Mobility / Transport

PETROL COMPRESSORP7070-RE• Heavy Duty Cast Iron Slow RPM Pump • Genuine Condor Pressure Switches • High Quality Powdercoat Finish• 70 Ltr Tank - Electric start 7HP

• Conrader Control Valve Fitted

• Includes Filter Regulator & Liquid Filled Gauge

BONUS10Mtr Air Hose

BONUS10Mtr Air Hose

$2,13043$2,450.00 GST Incl.

+GST$1,65130$1,899.00 GST Incl.

+GST

AIR COMPRESSOR 16CFM16RSE-DC

For heavy duty professional work. Quiet running. Dual control - Automatic STOP/START pressure switch control. Automatic free running air governor. 2.7 HP motor. Cast iron pump and cylinders. 445 lpm /15.7 cfm displacement / 300 lpm free air delivery. 1 year warranty.

BONUSFR05 Filter Reg &

HALF1010A Air Hose

$1,92000$2,208.00 GST Incl.

+GST

$11738$134.99 GST Incl.

+GST

$17304$199.00 GST Incl.

+GST$69478$799.00 GST Incl.

+GST

$15679$180.31 GST Incl.

+GST

GRAVITY SPRAY GUNW7014

Fully adjustable wide spray fan pattern control. Fluid tip 1.4mm.

Air consumption 7-9 cfm. Complete with 600ml cup. W7014-2 model

available with 2mm tip.

GOLD HIGH PRESSURE SPRAY GUNW7002S

Fully adjustable wide spray fan pattern control. Fluid tip 1.8mm. Air consumption 7-9 cfm. Ideal for both lacquers and enamels.

AIR HOSE RETRACTABLE REELSSteel body reel. Industrial grade rubber air hose made in Germany. Working Pressure: 21Bar/300psi. Inlet/Outlet. 1/4: (F in/M out).

DB320-2-50-P30015m x 10mm

DB330-2-65-P300 20m x 10mm

DB330-3-50-P30015m x 13mm

BONUSSwivel Wall

Mounting Bracket$20900$240.35 GST Incl.

+GST

$24900$286.35 GST Incl.

+GST

$25500$293.25 GST Incl.

+GST

TDR DIGITAL TYRE INFLATORJP10.3100Multi scale gauge. Quick and easy to use.Auto on/off. Backlight digital display. Dual hold-on chuck. Certificate of calibration. Tough precision die cast body. Dual impact absorbing bumpers. Supply Pressure Maximum 200 p.s.i. (1380 kPa). Minimum 100 p.s.i. (690 kPa). Connection Inlet 1/4” BSP. Internal thread. Hose length 500mm. Dual hold-on chuck. $15223


EL SERIES AIR HOSE REELHR40030

High quality impact and UV resistant polypropylene covers. Supplied complete with 20m x 10mm ID PVC hose and 0.9mm lead in hose, 3/8” BSP inlet and outlet threads, highflow swivel and fluid path. Max. working pressure of 300psi (20bar.) Automatic and positive latching system. Hose guide system rewinds the

hose without kinks. Constant speed control device ensures safe and accurate rewinding. Detachable steel mounting bracket enables 180° hose reel rotation. Can be wall, ceiling or floor mounted.

$24731$284.41 GST Incl.

+GST

50CM HIGH VELOCITY FLOOR/WALL FANTLS0050FW

Floor use or Wall/Ceiling Mountable (Bracket not included). Adjustable Fan Angle (+45 to -45 degree). Air flow 3,600 / 4,200 / 4,800cmh.

106CM HIGH CAPACITY BELT DRIVE BARRELL FANTLS0106

Belt-Driven Design, Durable Barrell Design. 2 Speed Fan Settings. 4 Heavy-Duty Balanced Steel Fan Blades.

$34696$399.00 GST Incl.

+GST

76CM HIGH VELOCITY FANSPerfect for blowing air in the garage or workshop. 3 speed settings. HD Steel fan blades. Air flow 6,000 / 7,000 / 8,500cmh.

TLS0076F 76cm Floor FanTLS0076P 76cm Pedestal FanTLS0076W 76cm Wall-Mounted Fan

Fixed axle, puncture proof wheels. Steel Housing, Powder Coat finish. Air flow 9,800 / 14,200cmh.

17

APPRENTICE TOOL CHEST 189PCCCT009F

9 Drawer Tool Chest, Racing Series. 38pc Gearless Ratchet Driver and Bits Tray. 94pc Socket, Driver & Accessory Tray. 31pc Plier, Hex Key & Adjustable Wrench Tray. 25pc Ring and Open End Spanners & Screwdriver Tray.

BONUSEKS0134 24W Portable LED

Work Lamp 2000 Lumens.

$1,04261$1,199 GST Incl.

+GST$1,04261

$1,199 GST Incl.+GST

TRADIE SITE BOXES

$34696$399.00 GST Incl.

+GST

RMS6181Tradie 36" Site Box with Gas Struts - 155L

RMS6180Tradie 3pc Site Box Set

TOOL CHEST 63PCGCAZ0039

Concertina tool box 470 x 220 x 350mm. 1/2” drive socket set 10-32mm. Complete with screwdrivers, pliers, wrenches, hex keys, hammers. The perfect portable tool kit.

TAP & DIE SET COMBINATION RATCHETING LARGE 114PC81032

45PC 1/4" SLIM HEAD RATCHET SETQuick release locking flex slim head ratchet 6” & 12”¼” Drive extension 4”¼” Drive 6 point standard Metric socket 4-13mm

ELEPHANT MANUAL CHAIN HOIST 2.0TONHOIC-C210203

High Quality Lifting Gear that you can rely onSuperior Power-to-Weight PerformanceMade in Japan.3.0M Lift 7.5mm Load Chain.

ELEPHANT CHAIN LEVER HOIST 1.6TONHOIL-YA016015

True one-touch free spooling, automatically brakes when load is appliedHigh Quality; Made in Japan.1.5M Lift 7.1mm Load Chain.

1.6TON / 1500KG JACK STANDS (DBL SAFETY)WTA1500

Complies with Australia/New Zealand standards AS/NZS 2538:2004. Heavy duty stamped steel frames with fully welded seams for strength. Supplied per pair. Rating is per stand. Support range 278mm to 428mm.

$49900$573.85 GST Incl.

+GST

$15900$182.85 GST Incl.

+GST

$35269$405.59 GST Incl.

+GST

$30224$347.58 GST Incl.

+GST

$4783$55.00 GST Incl.

+GST

BONUSAOS0118H Magic Wand LED Light

STORAGE SOLUTIONSRacing Series. Heavy Duty.


RMS6153 9 Drawer Tool Chest $320.87 $369.00RMS6156 7 Drawer Roll Cab $607.83 $699.00RMS6159 3 Drawer Tool Chest $216.52 $249.00

TOOL KIT 186PCGCBZ186A

Includes 9 drawer top chest. Designed for the NZ market. Ideal tool set for engineers & mechanics. AF & Metric 1/4, 3/8, 1/2” Dr. Socket Sets. Sizes: 4 - 32mm, 5/32” - 1.1/4”. R&OE Spanners AF & Metric 6 - 24mm, 1/4” - 1”, and much, much more!!!

$1,41000$1,621.50 GST Incl.

+GSTBONUS

GAAI5401 SOCKET & BIT SET

MULTI RACK STORAGE SOLUTION KKP11016 Shelves with 310mm shelf depth. Holds up to 50kg per shelf (Max total 300Kg). DIY assembly and installation. Suitable for internal and external storage applications. High quality powder coated steel construction. Assemble all shelves or remove some horizontal bars to increase the shelf height to suit your materials. Accessories shown not included

$7030$80.84 GST Incl.

+GST

$28609$329.00 GST Incl.

+GST

3.3TON / 3000KG GARAGE JACKWTJ3000

Heavy duty design with superior lifting capacity. Extra wide frame and wheel for stability. Lifting range: 140mm to 520mm.

$10127$116.46 GST Incl.

+GST

HYDRAULIC CRIMPER 4-70MM2 COMPLETE WITH DIESMA2340

Comes with 8 sets of interchanged dies to suit lug size 4mm2 - 70mm2. Overall length 320mm.

plus bit set.

18

GEARWRENCH 64 PIECE 120XP 1/4″ 3/8″ & 1/2"″ DRIVE SOCKET SET METRIC/SAE83066

120XP Ratchet delivers speed, access and torqueTear-Drop shaped slim head Ratchet for greater access with a 15% longer balanced handleLarge hard stamped identification on sockets.

SOCKET SET 26PC 3/4" DRGCAD2608

• 26 Pc Industrial Grade 3/8” Drive 12pt 22-50mm / 12pt 7/8”-2”

• 2 x Extensions 4” & 8”• 1 x 24T Ratchet• 1 x Sliding T Handle • Metal carry case

$25671$295.22 GST Incl.

+GST

$45700$525.55 GST Incl.

+GST

$12239$140.75 GST Incl.

+GST

$26090$300.03 GST Incl.

+GST

$35239$405.25 GST Incl.

+GST

BONUSEAS0635 3pc Hose

Line Clamp Set

1/2" DR COMBINATION SOCKET SET - 42PCKT4042CR06

Metric: 10-32mm. Imperial: 5/16-1.1/4”. 12pt Sockets. 6 x accessories. Made in Taiwan.

$28900$332.35 GST Incl.

+GST

TORX SOCKET SET 35PC645020

Torx & Tamper proof, Torx Male, Torx Female. 1/4”, 3/8” & 1/2” Dr. Built to exceed ANSI specifications. Heat treated, chrome vanadium steel. Offers Z-Drive for stronger grip. Features two grease rings for superior user grip.

$7391$85.00 GST Incl.

+GST

3/4" DR SOCKET SET 27PCKB3103Combination Socket Set. Ranges 22 - 50mm & 7/8” - 2”

$34348$395.00 GST Incl.

+GST

$19913$229.00 GST Incl.

+GST

BONUS941330 1/4"dr 40pc

Combination Socket & Bit Set

1/2” DR COMBINATION SOCKET SET 44PCKBT2768

1/2” Dr. (12pt Std) Sockets 10 - 36mm, 1/2 - 1 1/8”. Drive Accessories: 1/2” Dr. Gear to Gear Ratchet (48T), spark plug sockets, extensions, power bar, sliding t bar, universal joint.

$6522$75.00 GST Incl.

+GST

1/2” DR 22PC IMPACT DRIVER & BITS SETWBT0436Used to loosen rusted or over-tightened fasteners, reversible, can be used left or right direction. Handle design prevents possibility of hitting hand with hammer when striking impact driver.

$5900$67.85 GST Incl.

+GST$6300


HEX BIT SOCKET SETS 1/2” DR

GAAD1007 10pc - 55mm long Includes 4 - 19mm

GAAD0905 9pc - 80mm long Includes 4 - 17mm.

1/2" DR 10PC IMPACT SOCKET SETS


GDAD1001 ½” Drive 6pt, 10 piece, 10, 11, 12, 13, 14, 17, 19, 21, 22, 24 mm. $76.00 $87.40

GDAD1002 ½” Drive 6pt deep, 10 piece, 10, 11, 12, 13, 14, 17, 19, 21, 22, 24 mm. $108.00 $124.20

½”DR DEEP IMPACT SOCKET SET 13PC14208M

10-27mm 6pt SocketsLifetime Guarantee.

½” DR INHEX BIT SOCKET SET 10PC4012M/10

5-19mmFamous Ko-ken QualityMade in Japan.

½”DR COMBINATION SOCKET SET 36PC4279AM3/8-1.1/4" & 10-32mm SocketsAlso includes Ratchet, Extensions, Universal Joint, Sliding T Bar.

BONUSKo-ken Cap

BONUSKo-ken Cooler Bag

19

2-IN-1 METRIC GEAR SPANNER SET640974H

Gear spanners are just that, a spanner with a ratcheting gear mechanism in the ring head. Making them ideal for fast & speedy loosening or tightening of nuts. This unique set of 2 Gear Spanners offers 8 different sizes (one size per side each end). Includes 8-19mm.

$5217$59.99 GST Incl.

+GST

ADJUSTABLE WRENCHESBuilt to exceed ANSI specifications. Drop forged, chrome vanadium steel. ‘Euro Design’ type handle for greater comfort at higher torque applications with positive grip and balance. Metric scale on jaw for easy fastener size identification.

BALL PEIN GRAPHITE HAMMERSCarbon steel head. Polished face, poll, cheek and pein Graphite handle with TPR rubber grip

Code Description +GST Inclusive940208HS Adjustable Wrench 375mm $56.52 $65.00WES5011 Adjustable Wrench 450mm $68.70 $79.00WES5012 Adjustable Wrench 600mm $112.17 $129.00

Code Description +GST InclusiveHBS1109 16oz Ball Pein Graphite Hammer $13.04 $15.00HBS1110 24oz Ball Pein Graphite Hammer $15.65 $18.00HBS1111 32oz Ball Pein Graphite Hammer $16.52 $19.00

EUROPEAN LEFT HAND PATTERN

POWER BARSPlain handle grip. Extra torque for those stubborn nuts & bolts.

Code Description +GST InclusiveCFBC1215 Power Bar, 3/8" Drive x 15" Long $43.00 $49.45CFBC1624 Power Bar 1/2" Drive x 24" Long $65.50 $75.33CFBC1630 Power Bar 1/2" Drive x 30" Long $72.00 $82.80CFBC2440 Power Bar 3/4" Drive x 40" Long $169.00 $194.35CFBC3240 Power Bar 1" Drive x 40" Long $179.00 $205.85

ADJUSTABLE WRENCH 200MM9031

Extra wide opening jaws to 38mm. Measurement scale on the head.

$3881$44.63 GST Incl.

+GST$4627


WIDE JAW ADJUSTABLE WRENCH THIN JAW 200MM

9031-T

45% thinner jaws, compared to a standard adjustable

wrench of equivalent size. Code Description +GST Inclusive9070P 6" Combination Adjustable Wrench $31.34 $36.049071P 8" Combination Adjustable Wrench $35.82 $41.199072P 10" Combination Adjustable Wrench $40.30 $46.349073P 12" Combination Adjustable Wrench $47.77 $54.93

COMBINATION ADJUSTABLE WRENCHESReversible adjustable wrench, phosphated, thermoplastic handle. Can be used as a standard adjustable wrench or as a pipe wrench. Made in Spain.

C HOOK WRENCHES

Code Description +GST Inclusive315150 C-Hook Wrench 3/4 - 2" $37.91 $43.60315151 C-Hook Wrench 1.1/4 - 3" $56.43 $64.90315152 C-Hook Wrench 2 - 4.3/4" $70.03 $80.53315153 C Hook Wrench 4 1/2" - 6 1/4" $94.06 $108.17

3PC PRY BAR SET ROLLED HEAD ADJUSTABLE321076

• High leverage design with smooth curved head • Adjustable head 180° permits prying and lifting in confined area • Push lock function for ease of use • Ergonomic knurled handle for secure grip • Manufactured from high strength chrome vanadium steel with black phosphate finish to resist corrosion

• Suitable for automotive and industrial applications • Lengths: 200mm, 250mm & 330mm • Supplied in custom blow moulded plastic hard case.

$18209$209.40 GST Incl.

+GST

6PC HOLLOW WAD PUNCH SET321200

Feature precisely ground induction hardened and tempered cutting edges. Special design tip to prevent jamming of material inside the punch. Manufactured from hardened steel with industrial black finish for strength and durability.6 piece set supplied in plastic case.

$3469$39.89 GST Incl.

+GST

$34500$396.75 GST Incl.

+GST

$12777$146.94 GST Incl.

+GST

BEARING AND SEAL INSTALLATION KIT301350BP

Eliminates damage to bearings and seals. Cones may be used either side. Comprises of 9 tapered cones between 40 and 80mm plus a screw attachable driver shaft of 140mm in length.

ROE SPANNER SET METRIC 26PCKT1226MRN

Sizes 6 - 32mm.

SCREWDRIVER SET 14PCKT35114MR01

With phillips and flat tip screwdrivers. Includes an insulated pozi screwdriver.

$7286$83.79 GST Incl.

+GST

20

BOTTLE JACK 12 TONJACB-T91204

Capacity: 12 TonMin Height: 230mmLift Height: 155mmAdjusting Height: 80mm

GARAGE FLOOR JACK 3TONJACG-03LP

Access low clearance heights with this popular floor jack Lift Capacity : 3 Ton Minimum Height : 85mm Maximum Height : 455mm

TOOL BOX WITH TRAYBOXT-101

• Great for home storage or for mechanics• Comfortable grip handle, strong, durable &

dependable• Heavy duty gauge steel, corrosion resistant powder

coated finish484 x 152 x 165mm

SQUAT JACK 20 TON JACB-2004DS

• Single stage ram with high quality, glide action pressure pump

• Wide base plate for stability and strength.Min Ht 176mm / Max Ht 240mm

FARM JACK 33"JACF-33

• Ratcheting action jack• For lifting tractors, heavy trucks, pulling posts, poles• Lifting load capacity is 3 Ton (at 300mm)Min Height 153mm / Max Height 700mm 890 x 245 x 140mm

HYDRAULIC PORTABLE POWER KIT 10 TONPULD-10L

Supplied in convenient heavy duty transport case, with wheels. Includes hand pump with hose, cylinder ram, spreader ram and more

$5896$67.80 GST Incl.

+GST$25104$288.70 GST Incl.

+GST

$3250$37.38 GST Incl.

+GST

$8950$102.93 GST Incl.

+GST

$11500$132.25 GST Incl.

+GST

$39104$449.70 GST Incl.

+GST

BOTTLE JACK 20 TONJACB-T92004

Capacity: 20 TonMin Height: 242mmLift Height: 150mmAdjusting Height: 60mm

$8209$94.40 GST Incl.

+GST

Workshop JacksAxle Stands

Bottle JacksHydraulic Presses

BONUSBig Red Cap

BONUSBig Red Cap

21

Tools for Life!

Code No.

662794 1525 Tool Trolley - EMPTY

Code No.

660965 1425 / 5 Tool Chest - EMPTY

Code No. Contents

8725200 106 97 - 125 97 - 150 98 - 125 99 - 12-3 100 - 10 119 - 4

Code No. Contents

8757670 116 A 119 - 3 119 - 4 119 - 5 119 - 6 119 - 7 119 -8

Code No. Contents

8753680 113 99 - 10-1 99 - 10-2 99 - 10-3 99 - 12-4 99 - 12-5 100 - 10

Code No.. Contents

1616048 VDE 2170-2160 PH 06 ? VDE 2170 3.5 4 5.5 6.5; VDE 2160 PH1 PH2

$1386.99Ex. GST

1525TOOL TROLLEY

$1 595.04Incl. GST

$876.24Ex. GST

1425/5 TOOL CHEST

$1 007.68Incl. GST

$62.00Ex. GST

VDE 2160-21703C SCREWDRIVER SET

$71.30Incl. GST

$60.50Ex. GST

2150-2160 PH-06 MS3C SCREWDRIVER SET

$69.58Incl. GST

$65.43Ex. GST

2150-2160 PH-06 ELS3C SCREWDRIVER SET

$75.24Incl. GST

$141.76Ex. GST

2163 TX3C TORX® SCREWDRIVER SET

$163.02Incl. GST

$74.37Ex. GST

106CHISEL & PUNCH SET

$85.52Incl. GST

$57.51Ex. GST

113DRIFT PUNCH SET

$66.14Incl. GST

$90.73Ex. GST

116APIN PUNCH SET

$104.34Incl. GST

Code No. Contents

1482335 2163TX 7 2163 T7 T8 T9 T10 T15 T20 T25 T27 T30 T40

Code No. Contents

1482319 2150-2160 PH-06 MS ? 2150 4 5.5 6.5 8; 2160 PH1 PH2

Code No. Contents

1482320 2150-2160 PH-06 ELS ? 2150 6.5 3-150 4-150 6.5-200; 2160 PH1 PH2

BONUS20NZA 1/4”socket set

BONUSD30 NZZ 3/8”socket set

22

Tools for Life!GEDORE is exclusiveto TradeZone

Every GEDORE hand tool enjoys a lifetime guarantee and dedicated after sales service.

Visit www.tradezone.co.nzTo see the New Zealand range.

Code ! y Ex. GST Incl. GST

636800B 150 20 150 $32.09 $36.90636819B 200 25 200 $35.48 $40.80636827B 250 30 250 $39.39 $45.30636835B 300 36 300 $47.30 $54.40636851C 450 53 450 $94.61 $108.80

Code No. Ratchet

6172460 No.20 NZA ! 2093 Z-94

Sockets Accessories

1/4“ drive sockets 4 4,5 5 6 7 8 9 10 11 12 13 143/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2

+ 2087 2090-2 / 4 Extensions

) 209520982088 Flexible ExtensionFoam InsertPlastic Case

Code No. Ratchet

6172465 No.20 NZI ! 2093 Z-94

Sockets Accessories1/4“ drive sockets 4 4.5 5 6 7 8 9 10 11 12 13 14mm Torx T8 T10 T15 T20 T25 T27 T30 T40 Screwdriver bits IS20 4 5.5 6.5 7 Screwdriver sockets IKS20 PH0 PH1 PH2 PH3

2090-2 / 4 Extensions) 2095

2098+ 2087

2088 Flexible ExtensionFoam InsertPlastic Case

Code No. Ratchet

623968 D30 NZZ ! 3093 Z94

$202.21Ex. GST

20 NZA SOCKET SET 1/4“

$232.54Incl. GST

$124.87Ex. GST

20 NZI SOCKET SET 1/4“

$143.60Incl. GST

$310.06Ex. GST

D30 NZZ SOCKET SET 3/8“

$356.56Incl. GST

Sockets Accessories

3 D 30 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22mm 1/4 9/32 5/16 11/32 3/8 7/16 1/2 9/16 19/32 5/8 11/16 3/4 25/32 13/16 7/8

3090 125mm Extension 3090 250mm Extension+ 3087 Sliding T bar

Foam InsertMetal Case

$363.98Ex. GST

D19 NZU-Z94 SOCKET SET 1/2“

$418.58Incl. GST

$741.44Ex. GST

D32 NZU-Z SOCKET SET 3/4“

$852.65Incl. GST

Code No. Ratchet

615298 D19 NZU-Z94 ! 1993 Z-94

Code No. Ratchet

628073 D32 NZU-Z " 3293 U-2Sockets Accessories

D32 22 24 27 29 30 32 36 38 41 46 50mm 7/8 15/16 1.1/16 1.1/4 1.5/16 1.3/8 1.7/16 1.5/8 1.13/16 2

+ 32873290-2003290-400

Sockets AccessoriesD19 10 11 12 13 14 15 16 17 18 19 21 22 23 24 26 27 30 32mm 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4

1990-125, 250 Extensions) 1995

1987 Sliding T bar Foam Insert

Metal Case 50/20.8mm

62ADJUSTABLE WRENCHES

1BSPANNER SETS

Code ! " Contents Ex. GST Incl. GST601200 1B-10M 10 11 12 13 14 15 16 17 18 19 $128.17 $147.40601268TR 1B-17M WITH TOOL ROLL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 $240.35 $276.40601276TR 1B-26M WITH TOOL ROLL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

25 26 27 28 29 30 32 $507.39 $583.50

601209 1B-017A 1/4” 5/16” 3/8” 7/16” 1/2” 9/16” 5/8” 11/16” 3/4” 13/16” 7/8” 15/16” 1.” 1.1/16” 1.1/8” 1.3/16” 1.1/4”

$360.52 $414.60

Code No. a „ Nm y

3014398 3550-UK-LS 3 1/2 40-200 499

17mm 19mm 21mm

FREE with 3550-UK-LS 3

$198.19Ex. GST

S8003 JC PLIERS SET

$227.92Incl. GST

$219.87Ex. GST

S8303 JC PLIERS SET

$252.85Incl. GST

$128.58Ex. GST

S8000CIRCLIP PLIERS SET

$147.87Incl. GST

Code No. Contents

6701110 S 8003 JC 8132-200 JC Telephone Pliers8250-200 JC Combination Pliers8316-200 JC Side Cutters

Code No. Contents

6703160 S 8303 JC 142 10 JC Universal Pliers8250-180 JC Combination Pliers8316-160 JC Side Cutters

Code No. Contents

6701030 S 8000 External: 8000-A2 Straight 8000-A21 AngledInternal: 8000-J2 Straight 8000-J21 Angled

$131.48Ex. GST

ITX19MALE TORX® SOCKET SET 1/2“

$151.20Incl. GST

$105.13Ex. GST

TX19FEMALE TORX® SOCKET SET 1/2“

$120.90Incl. GST

$111.74Ex. GST

IN19 PM-10 ALLEN KEY SOCKET SET 1/2“

$128.50Incl. GST

Code No. Sockets617415 PM-10 IN19 5 6 7 8 9 10 12 14 17 19

Code No. Sockets665983 MT ITX19 T20 T25 T27 T30 T40 T45 T50

Code No. Sockets665991 FT TX19 E10 E11 E12 E14 E16 E18 E20 E24

3550-UK-LS-3TORQUE WRENCH 1/2“

$428.87Ex. GST

$493.20Incl. GST

BONUS2150-2160PH -06 MSscrewdriverset

BONUSGEDOREdrinkbottle


BONUSGEDOREbluetoothspeaker





bluetooth

er

Silver only. Stocks limited

23

Tools for Life!GEDORE is exclusiveto TradeZone

Every GEDORE hand tool enjoys a lifetime guarantee and dedicated after sales service.

Visit www.tradezone.co.nzTo see the New Zealand range.

Code ! y Ex. GST Incl. GST

636800B 150 20 150 $32.09 $36.90636819B 200 25 200 $35.48 $40.80636827B 250 30 250 $39.39 $45.30636835B 300 36 300 $47.30 $54.40636851C 450 53 450 $94.61 $108.80

Code No. Ratchet

6172460 No.20 NZA ! 2093 Z-94

Sockets Accessories

1/4“ drive sockets 4 4,5 5 6 7 8 9 10 11 12 13 143/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2

+ 2087 2090-2 / 4 Extensions

) 209520982088 Flexible ExtensionFoam InsertPlastic Case

Code No. Ratchet

6172465 No.20 NZI ! 2093 Z-94

Sockets Accessories1/4“ drive sockets 4 4.5 5 6 7 8 9 10 11 12 13 14mm Torx T8 T10 T15 T20 T25 T27 T30 T40 Screwdriver bits IS20 4 5.5 6.5 7 Screwdriver sockets IKS20 PH0 PH1 PH2 PH3

2090-2 / 4 Extensions) 2095

2098+ 2087

2088 Flexible ExtensionFoam InsertPlastic Case

Code No. Ratchet

623968 D30 NZZ ! 3093 Z94

$202.21Ex. GST

20 NZA SOCKET SET 1/4“

$232.54Incl. GST

$124.87Ex. GST

20 NZI SOCKET SET 1/4“

$143.60Incl. GST

$310.06Ex. GST

D30 NZZ SOCKET SET 3/8“

$356.56Incl. GST

Sockets Accessories

3 D 30 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22mm 1/4 9/32 5/16 11/32 3/8 7/16 1/2 9/16 19/32 5/8 11/16 3/4 25/32 13/16 7/8

3090 125mm Extension 3090 250mm Extension+ 3087 Sliding T bar

Foam InsertMetal Case

$363.98Ex. GST

D19 NZU-Z94 SOCKET SET 1/2“

$418.58Incl. GST

$741.44Ex. GST

D32 NZU-Z SOCKET SET 3/4“

$852.65Incl. GST

Code No. Ratchet

615298 D19 NZU-Z94 ! 1993 Z-94

Code No. Ratchet

628073 D32 NZU-Z " 3293 U-2Sockets Accessories

D32 22 24 27 29 30 32 36 38 41 46 50mm 7/8 15/16 1.1/16 1.1/4 1.5/16 1.3/8 1.7/16 1.5/8 1.13/16 2

+ 32873290-2003290-400

Sockets AccessoriesD19 10 11 12 13 14 15 16 17 18 19 21 22 23 24 26 27 30 32mm 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1.1/16 1.1/8 1.3/16 1.1/4

1990-125, 250 Extensions) 1995

1987 Sliding T bar Foam Insert

Metal Case 50/20.8mm

62ADJUSTABLE WRENCHES

1BSPANNER SETS

Code ! " Contents Ex. GST Incl. GST601200 1B-10M 10 11 12 13 14 15 16 17 18 19 $128.17 $147.40601268TR 1B-17M WITH TOOL ROLL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 $240.35 $276.40601276TR 1B-26M WITH TOOL ROLL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

25 26 27 28 29 30 32 $507.39 $583.50

601209 1B-017A 1/4” 5/16” 3/8” 7/16” 1/2” 9/16” 5/8” 11/16” 3/4” 13/16” 7/8” 15/16” 1.” 1.1/16” 1.1/8” 1.3/16” 1.1/4”

$360.52 $414.60

Code No. a „ Nm y

3014398 3550-UK-LS 3 1/2 40-200 499

17mm 19mm 21mm

FREE with 3550-UK-LS 3

$198.19Ex. GST

S8003 JC PLIERS SET

$227.92Incl. GST

$219.87Ex. GST

S8303 JC PLIERS SET

$252.85Incl. GST

$128.58Ex. GST

S8000CIRCLIP PLIERS SET

$147.87Incl. GST

Code No. Contents

6701110 S 8003 JC 8132-200 JC Telephone Pliers8250-200 JC Combination Pliers8316-200 JC Side Cutters

Code No. Contents

6703160 S 8303 JC 142 10 JC Universal Pliers8250-180 JC Combination Pliers8316-160 JC Side Cutters

Code No. Contents

6701030 S 8000 External: 8000-A2 Straight 8000-A21 AngledInternal: 8000-J2 Straight 8000-J21 Angled

$131.48Ex. GST

ITX19MALE TORX® SOCKET SET 1/2“

$151.20Incl. GST

$105.13Ex. GST

TX19FEMALE TORX® SOCKET SET 1/2“

$120.90Incl. GST

$111.74Ex. GST

IN19 PM-10 ALLEN KEY SOCKET SET 1/2“

$128.50Incl. GST

Code No. Sockets617415 PM-10 IN19 5 6 7 8 9 10 12 14 17 19

Code No. Sockets665983 MT ITX19 T20 T25 T27 T30 T40 T45 T50

Code No. Sockets665991 FT TX19 E10 E11 E12 E14 E16 E18 E20 E24

3550-UK-LS-3TORQUE WRENCH 1/2“

$428.87Ex. GST

$493.20Incl. GST

BONUS2150-2160PH -06 MSscrewdriverset








bluetooth

er

Silver only. Stocks limited

Your local TradeZone Store

www.tradezone.co.nz

We are a fair-minded company and try to exceed the requirements of the ‘Fair Trading’ legislation. Prices are current for the period denoted on the cover. Stocks are not always available in all stores all the time but we will try our best to obtain more or equivalent substitutes. Errors and omissions are rare but can happen, so we apologise and try to take all reasonable measures to fix the issue for you.24

If you’re unable to get to us, please phone, fax or email us and we’ll deliver it directly to you.

COLD PETROL WATER BLASTERBAR2765C-H

COLD PETROL WATER BLASTERBAR3270A-R

Powerease 7.0Hp Motor, AR Triplex Pump, 3200PSI, 11 l/min, 10mtr Hose, Comes with Gun, Lance and Nozzles.

$1,52174$1,750.00 GST Incl.

+GST

$1,73826$1,999.00 GST Incl.

+GST

$94900$1,091.35 GST Incl.

+GST

BONUSBAR1400 Surface

Cleaner

BONUSHour Meter, Car

Cleaning Kit, Foldable Funnel Great Bungee, Tip Cleaner, Detergent.

• Honda GX200 196cc• 2700 Psi max pressure• 11.3 l/min• Comet Pump LWD3025G

• Comes with gun, lance & nozzles

• 9.1mtr Hose

HONDA PRESSURE WASHER 4200PSIBAR4213J-H

15L/min, 13HP Honda Motor Recoil Start, CAT Plunger pump with Brass head, 15m hose Gun Lance and 4 x Q/C Noz included.

$2,26000$2,599.00 GST Incl.

+GST

BONUS125 RJ-4035-CS Turbo

Nozzle.

1-1/2” HIGH PRESSURE PUMP - POWEREASEHP15701-R

Performance: 330L/min. 7 Metres Suction. 55 Metres Total Head. Powerease R210 7.0HP Petrol Engine.Air cooled 4-stroke OHV. Recoil Start.3.6L Fuel Tank. Low Oil Alert.

$43391$499.00 GST Incl.

+GST$65217


2” HONDA WATER PUMPWB20

Honda GX120 Motor. 600Lpm. 32Mtr Head. 8Mtr Suction. Suction/Discharge Port 50mm. 2.5Ltr Fuel Tank

COLD PETROL WATER BLASTER BAR4015C-R

Powerease 15HP Motor15Ltr/min 4000 Psi comet Pump15m Hose.

BONUS125 RJ-4035-CS Turbo

Nozzle.

nz’s indust rial suppl y specialists suppliers to indust ry · bolts and fasteners. our cordless...

Documents