Olympus Pen E-PL7 LCD Screen ReplacementThis guide will show you how to remove the LCD from the Olympus Pen E-PL7

Geschrieben von: Kelsea Weber

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 1 von 8

EINLEITUNG

Is your LCD Screen cracked or unresponsive? Use this guide to replace it and get back to takingawesome photos.

We highly suggest you use a magnetic project mat or an organization tray. This camera has manydifferent types of screws and keeping them organized is key to proper reassembly.

WERKZEUGE:Tweezers (1)Phillips #00 Screwdriver (1)Magnetic Project Mat (1)

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 2 von 8

Schritt 1 — Battery

Turn the camera upside down.

Push the grey tab to the right to open the battery compartment.

Pull out the battery.

The battery is not shown in these photos.

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 3 von 8

Schritt 2 — LCD Screen

Use a Phillips #00 screwdriver toremove the three 2.3 mm screwsfrom the base of the LCD screen.

Schritt 3

Fully extend the LCD assembly.

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 4 von 8

Schritt 4

Remove the two 2.2 mm Phillips screws located on the back of the LCD screen.

Use tweezers to remove the top LCD bracket.

Schritt 5

Use a Phillips #00 screwdriver to remove the four 1.4 mm screws from the back of the LCD screen.

Remove the LCD ribbon cable with a pair of tweezers.

The cover may fall off after the screws have been removed.

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 5 von 8

Schritt 6

Carefully lift the LCD screen up and away from the assembly.

Do not attempt to fully remove the screen, as it is attached to the assembly by a ribbon cable.

Schritt 7

Use tweezers to peel back the plastic cover.

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 6 von 8

Schritt 8

Use a spudger to flip back the black bar on the LCD Ribbon ZIF connector.

Schritt 9

Gently pull the ribbon cable out with tweezers.

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 7 von 8

To reassemble your device, follow these instructions in reverse order.

Schritt 10

Remove the LCD Screen.

Olympus Pen E-PL7 LCD Screen Replacement Entwurf: 2016-03-18Anleitung Nr: 55390 -

Dieses Dokument wurde am 2019-12-01 05:53:50 AM (MST) erstellt.

© iFixit — CC BY-NC-SA de.iFixit.com Seite 8 von 8