omfa motherboard - winmatedc.winmate.com.tw/_downloadcenter/2016/sbcmanual/omfa_v1... · 2016. 3....

OMFA Motherboard Freescale iMX6 Quad Core 1GHz processor, DDR3 1GB system memory, one

USB2.0 OTG, two USB2.0 host, two audio jacks for microphone, line-in and

line-out, optional Wi-Fi and 3G

V100

User Manual Version 1.0

Manual Number: 917111171003

User Manual II

Preface

Copyright Notice

No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer.

Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer We reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. We make no representation or warranty that such application will be suitable for the specified use without further testing or modification.

Warranty We warrant that each of its products will be free from material and workmanship defects for a period of one year from the invoice date. (Standard is one year, extended warranty will need to discuss with our sales representatives. If the customer discovers a defect, we will, at its option, repair or replace the defective product at no charge to the customer, provided it is returned during the warranty period of one year, with transportation charges prepaid. The returned product must be properly packaged in its original packaging to obtain warranty service. If the serial number and the product shipping data differ by over 30 days, the in-warranty service will be made according to the shipping date. In the serial numbers the third and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g., with A for October, B for November and C for December). For example, the serial number 1W16Axxxxxxxx means October of year 2016.

Packing List Before using this Motherboard, please make sure that all the items listed below are present in your package: OMFA Motherboard User Manual & Driver CD

User Manual III

If any of these items are missing or damaged, contact your distributor or sales representative immediately.

Customer Service We provide a service guide as below for any problem by the following steps: First, contact your distributor, sales representative, or our customer service center for technical support if you need additional assistance. You need to prepare the following information before you call:

Product serial number Peripheral attachments Software (OS, version, application software, etc.) Detailed problem description The exact wording of any error messages

In addition, free technical support is available from our engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. Please do not hesitate to call or e-mail us.

Advisory Conventions

Four types of advisories are used throughout the user manual to provide helpful

information or to alert you to the potential for hardware damage or personal injury.

These are Notes, Important, Cautions, and Warnings. The following is an example of each

type of advisory.

NOTE:

A note is used to emphasize helpful information

IMPORTANT:

An important note indicates information that is important for you to know.

CAUTION

A Caution alert indicates potential damage to hardware and explains how to

avoid the potential problem.

User Manual IV

WARNING!

An Electrical Shock Warning indicates the potential harm from electrical

hazards and how to avoid the potential problem.

Safety Precautions

CAUTION

Always ground yourself to remove any static charge before

touching the CPU card. Modern electronic devices are very

sensitive to static electric charges. As a safety precaution, use a

grounding wrist strap at all times. Place all electronic components

in a static-dissipative surface or static-shielded bag when they are

not in the chassis.

Safety and Warranty

1. Please read these safety instructions carefully.

2. Please keep this user manual for later reference.

3. Please disconnect this equipment from any AC outlet before cleaning. Do not

use liquid or spray detergents for cleaning. Use a damp cloth.

4. For pluggable equipment, the power outlet must be installed near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or

letting it fall could cause damage.

7. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

8. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

9. All cautions and warnings on the equipment should be noted.

10. If the equipment is not used for a long time, disconnect it from the power

source to avoid damage by transient over-voltage.

11. If any of the following situations arises, get the equipment checked by service

personnel:

A. The power cord or plug is damaged.

B. Liquid has penetrated into the equipment.

C. The equipment has been exposed to moisture.

D. The equipment does not work well, or you cannot get it to work according

to the user’s manual.

E. The equipment has been dropped and damaged.

F. The equipment has obvious signs of breakage.

User Manual V

Revision History

Version Date Note Author

1.0 14-March-2016 Initial release Austin Chang, edited by Anna Kiseleva

User Manual VI

Contents

Table of Contents

PREFACE .............................................................................................................................................. I

CHAPTER 1 GENERAL INFORMATION .................................................................................................. 2

1.1 INTRODUCTION ................................................................................................................................... 2

1.2 FEATURES .......................................................................................................................................... 2

1.3 MOTHERBOARD SPECIFICATIONS ............................................................................................................ 3

1.4 FUNCTIONAL DESCRIPTION.................................................................................................................... 4

1.5 PHYSICAL DESCRIPTION ........................................................................................................................ 5

CHAPTER 2 HARDWARE INSTALLATION .............................................................................................. 7

2.1 MOTHERBOARD COMPONENTS .............................................................................................................. 7

2.1.1 Front Side ............................................................................................................................... 7

2.1.2 Rear Side ................................................................................................................................ 8

2.1.3 I/O Side ................................................................................................................................... 8

2.2 CONNECTOR PIN ASSIGNMENTS ............................................................................................................. 9

2.2.1 Front Side ............................................................................................................................. 10

2.2.2 Rear Side .............................................................................................................................. 11

2.2.3 I/O Side ................................................................................................................................. 13

CHAPTER 3 SOFTWARE UPDATE ....................................................................................................... 20

3.1 ANDROID DEBUG BRIDGE (ADB) DRIVER INSTALLATION ........................................................................... 20

3.1.1 Disabling Driver Signature on Windows 8 ............................................................................ 21

3.1.2 ADB Driver Installation ......................................................................................................... 26

3.2 INSTALLING ANDROID DEBUG BRIDGE (ADB) ......................................................................................... 29

3.3 DOWNLOAD IMAGE TOOL ................................................................................................................... 31

3.4 OTA UPDATE GUIDE .......................................................................................................................... 31

3.5 OS IMAGE UPDATE GUIDE .................................................................................................................. 35

CHAPTER 4: TECHNICAL SUPPORT DOCUMENTS .............................................................................. 42

4.1 ANDROID SDK ................................................................................................................................. 42

OMFA Motherboard General Information

User Manual 1

General Information This chapter includes the OMFA motherboard background information.


User Manual 2

Chapter 1 General Information

1.1 Introduction

Thank you for choosing the OMFA Motherboard. The motherboard is powered by

Freescale iMX6 Quad Core 1GHz Processor that allows running on Android 4.4 operating

system. Android provides many options for easy software integration.

OMFA is designed for Open Pluggable Specification (OPS) module that can be installed

into the display panel through a single and standard interfacing based on the 80 pin JAE

plug and receptacle connectors. The power supply to the OMFA together with the

defined feature interfaces are being routed through the set of connectors, and provide a

functional system level computing solution for digital signage.

There is an advanced full set of I/O ports including one USB2.0 OTG, two USB2.0 host,

two audio jacks for microphone, line-in and line-out. The current model allows adding

Wi-Fi and 3G models for better connectivity and information exchange.

1.2 Features

Freescale iMX6 Quad Core 1GHz Processor

Android 4.4

DDR3 1GB System Memory

Integrated Graphics

1 x Power Button, 1 x Reset Button, 1 x USB2.0 Host, 2 x USB 2.0 OTG, 2 x Audio

Jack, 1 x RJ45

Wi-Fi and 3G Modules (optional)


User Manual 3

1.3 Motherboard Specifications

System Specification:

CPU Freescale Cortex™-A9 i.MX 6 Series Quad Core 1GHz

System Memory DDR3 1GB

OS Android 4.4

Storage On board 16GB eMMC, 1 x 2.5" SATA HDD/SSD

Graphic Chipset Integrated Graphics

Ethernet Gigabit Ethernet LAN

Audio Mic-in / Headphone

I/O Interface:

Front

1 x Power Button

1 x Reset button

2 x USB 2.0 Host

1 x USB 2.0 OTG

2 x Audio Jack (Line-in/ Line-out)

1 x RJ45

Rear (OPS Interconnector) 1 x JAE 80-Pin connector (follow OPS Standard)

Power Requirements:

Power Consumption 10W (burn in test)

Input Voltage 12V~19V DC in (via OPS interconnection)

Mechanical Dimensions:

Form Factor 3.5”

Environment:

Operating Temperature -10°C to 60°C

Operating Humidity 30%~ 90% (non-condensing, RH)

Certification

Electromagnetic CE, FCC

*Wireless Communication:

*Wi-Fi USB Wi-Fi Module

*3G Mini PCle 3G Module

*Wi-Fi and 3G are optional modules


User Manual 4

1.4 Functional Description

Function block (V100)


User Manual 5

1.5 Physical Description

Board Dimensions (V100)

OMFA Motherboard Hardware Installation

User Manual 6

Hardware Installation This chapter provides information on how to use

jumpers and connectors on the OMFA motherboard.


User Manual 7

Chapter 2 Hardware Installation

This chapter provides information on how to use jumpers and connectors on the

OMFA Motherboard. Be cautious while working with these modules. Carefully read

the content of this chapter in order to avoid any damages.

2.1 Motherboard Components

2.1.1 Front Side


User Manual 8

2.1.2 Rear Side

2.1.3 I/O Side

2.1.3.1 Top

SW1

USB 2.0

Mini-PCIE

Half Card


User Manual 9

2.1.3.2 Bottom

2.2 Connector Pin Assignments

This section explains how to set jumpers for correct configuration of the

motherboard.

NOTE:

A pair of needle nose pliers may be helpful when working with jumpers.

If you have any doubts about the best hardware configuration for your

application, contact your local distributor or sales representative before

you make any changes. Generally, you simply need a standard cable to

make most connections.

The jumper setting diagram is shown below. When the jumper cap is placed on both

pins, the jumper is SHORT. The illustration below shows a 3-pin jumper; pins 1 and 2

are short. If you remove the jumper cap, the jumper is OPEN.

CAUTION

To avoid damaging the module, always turn off the power supply

before setting jumpers or clearing CMOS.

1

2

3


User Manual 10

2.2.1 Front Side

Label Function Note

BT1 Backup Battery Wafer 1x2p P:1.25mm SMD 90

CN4 USB I/O Port Wafer 1x4p P:1.0mm 180° white color

CN18 SPI I/F Port Wafer 1x6p P:1.0mm SMD 180° white color

CN35 RS232 Wafer 1x4p P:1.0mm SMD 180° white color

CN37 Debug Port Wafer 1x6p P:1.0mm SMD 180° white color

BT1: Backup Battery

CN4: USB I/O Port

CN18: SPI I/F Port

Pin № Name

1 GND

2 BAT

Pin № Name

1 WIFI_PWR_5V

2 WIFI_USB_DM

3 WIFI_USB_DP

4 GND

Pin № Name

1 +V3.3S

2 ECSPI3_MISO

3 ECSPI3_MOSI

4 ECSPI3_CS1

5 ECSPI3_SCLK

6 GND


User Manual 11

CN35: RS232

CN37: Debug Port

2.2.2 Rear Side

Label Function Note

CN5 Micro-SIM Card Connector C-MSM01S030R

CN9 Min-PCIe Connector AS0B226-S40Q-7H

Pin № Name

1 VUART1

2 RS232_3_TX

3 RS232_3_RX

4 GND

Pin № Name

1 TXD232

2 NC

3 NC

4 RXD232

5 DBUG_5V

6 GND


User Manual 12

CN5: Micro-SIM Card Connector

CN9: Mini-PCIe Connector

Pin № Name Pin № Name

1 PCIE_WAKE# 2 PCIE_3V3

3 NC 4 GND

5 NC 6 PCIE_1V5

7 NC (*GND) 8 VREG_USIM

9 GND 10 SIM_DAT

11 PCIE_CLK1_N 12 SIM_CLK

13 PCIE_CLK1_P 14 SIM_RST

15 GND 16 SIM_VPP

17 NC 18 GND

19 NC 20 PCIE_PWR_EN

21 GND 22 PCIE_RST_N

23 PCIE_RXM_1 24 NC (*PCIE_3V3)

25 PCIE_RXP_1 26 GND

Pin № Name

C1 VREG_USIM

C2 USIM_RST

C3 USIM_CLK

C5 GND

C6 USIM_VPP

C7 USIM_DAT

SW USIM_DET (Default High, Active Low)

G1 NC

G2 NC

G3 GND

G4 GND


User Manual 13

27 GND 28 PCIE_1V5

29 GND 30 NC

31 PCIE_TXM_1 32 NC

33 PCIE_TXP_1 34 GND

35 GND 36 PCIE_USB_DM

37 GND 38 PCIE_USB_DP

39 PCIE_3V3 40 GND

41 PCIE_3V3 42 NC

43 GND 44 M7304_DPR

45 NC 46 NC

47 NC 48 PCIE_1V5

49 NC 50 GND

51 NC 52 PCIE_3V3

*optional

2.2.3 I/O Side

2.2.3.1 Top

Label Function Note

CN7 Line Out WTJ-035-82I Green

CN8 Mic In WTJ-035-82I PINK

CN21 Dual USB Type A Connector SUYIN 020122MR008S541ZL

CN30 Micro SD Slot 81CSD03S030R

CN32 Micro USB Port 22UBH-051-120L

LAN1 RJ45 Support 10/100/1000 Mbps LAN RT7-174AAM1A UDE

SW1 Power Key TC003-N11AABUBXX-RK WITH LED

SW4 Reset Key TSVB-31L 3mm 90°


User Manual 14

CN7: Line Out

CN8: Mic In

CN21: Dual USB Type A Connector

Pin № Name

1 HP_LIN

2 HP_RIN

3 GND

4 HEADPHONE_DET

5 GND

6 GND

7 NC

8 NC

Pin № Name

1 MIC_IN-

2 MIC_IN+

3 GND

4 MICROPHONE_DET

5 GND

6 GND

7 NC

8 NC

Pin № Name

1 VUSB_VBUS0

2 EXT_USB0_DM

3 EXT_USB0_DP

4 GND

5 VUSB_VBUS1

6 EXT_USB1_DM

7 EXT_USB1_DP

8 GND


User Manual 15

CN30: Micro SD Slot

CN32: Micro USB Port

LAN1: RJ45 Support 10/100/1000 Mbps

Pin № Name

1 SD3_DATA2

2 SD3_DATA 3

3 SD3_CMD

4 SD_3V3

5 SD3_CLK

6 GND

7 SD3_DATA0

8 SD3_DATA1

CD SD_CD#


1 VUSB_VOTG 2 USB_OTG_CON_DN

3 USB_OTG_CON_DP 4 USB_OTG_ID

5 GND 6 GND

7 GND 8 GND

9 GND


1 MDI0_IN+ 2 MDI0_IN-


5 NC 6 LAN1_DGND



11 +V3.3S 12 LAN1_ACTIVE_Y

13 LAN1_1000_O 14 LAN1_100_10_G

15 GND 16 GND


User Manual 16

SW1: Power Key

SW4: Reset Key

2.2.3.2 Bottom

Label Function Note

CN1 OPS Connector None

CN3 SATA HDD iSATA Conn LD2722F-S4GL6 DIP 90°

CN1: OPS Connector


1 DDP_3N 2 DDP_3P

3 GND 4 DDP_2N

5 DDP_2P 6 GND

Pin № Name

1 GND

2 GND

3 CPUPWRON

4 CPUPWRON

5 GND

6 +V3.3S

Pin № Name

1 PM_SYSRST#

2 GND

3 GND

4 GND


User Manual 17

7 DDP_1N 8 DDP_1P

9 GND 10 DDP_0N

11 DDP_0P 12 GND

13 DDP_AUXN 14 DDP_AUXP

15 DDP_HPD 16 GND

17 TMDS_CLK- 18 TMDS_CLK+

19 GND 20 TMDS0

21 TMDS0+ 22 GND

23 TMDS1- 24 TMDS1+

25 GND 26 TMDS2-

27 TMDS2+ 28 GND

29 H_DAT_OUT 30 H_CLK_OUT

31 HP_DET_OUT 32 GND

33 DC_IN 34 DC_IN

35 DC_IN 36 DC_IN

37 DC_IN 38 DC_IN

39 DC_IN 40 DC_IN

41 RSVD 42 RSVD

43 RSVD 44 RSVD

45 RSVD 46 RSVD

47 RSVD 48 RSVD

49 RSVD 50 CB_SYS_FAN

51 COM_RXD 52 COM_TXD

53 GND 54 StdA_SSRX

55 StdA_SSRX+ 56 GND

57 StdA_SSTX- 58 StdA_SSTX+

59 GND 60 USB_PN2

61 USB_PP2 62 GND

63 USB_PN1 64 USB_PP1

65 GND 66 USB_PN0

67 USB_PP0 68 GND

69 REAR_L 70 REAR_R

71 HDMI_CEC_OUT 72 PB_DET

73 PS_ON# 74 PWR_STATUS

75 GND 76 GND

77 GND 78 GND

79 GND 80 GND


User Manual 18

CN3: SATA HDD


1 GND 2 SATA_TXP0

3 SATA_TXN0 4 GND

5 SATA_RXN0 6 SATA_RXP0

7 GND 8 SATA_3V3

9 SATA_3V3 10 SATA_3V3

11 GND 12 GND

13 GND 14 +V5S

15 +V5S 16 +V5S

17 GND 18 NC

19 GND 20 NC

21 NC 22 NC

OMFA Motherboard Software Update

User Manual 19

Software Update This chapter contains software update guide for

OMFA motherboard.


User Manual 20

Chapter 3 Software Update

This chapter contains software installation and update guides. All the programming

guides can be found in the driver CD included in the package.

3.1 Android Debug Bridge (ADB) Driver Installation

You can find USB_OTG_driver in the following locations:

CDM v2.08.28 Certified\ftdibus.inf

CDM v2.08.28 Certified\ftdiport.inf

You need to connect OMFA motherboard to the computer with the USB 2.0 cable.

When using a USB cable (not supplied with your HMI device), verify that the cable or

cable packaging bears the “Certified USB™” mark (see below) to guarantee USB 2.0

compliance.

*I/O settings on the picture are for demonstration purposes only. Your I/O may vary

from the picture above.

IMPORTANT:

If your computer is running on Windows Embedded 8 Standard or

Windows 8.1 Industry Pro OS system, you need to disable driver

signature.

For Win XP / Win 7 skip disabling driver signature section, and

directly proceed to ADB driver installation.


User Manual 21

3.1.1 Disabling Driver Signature on Windows 8

Step 1 Hold down the Windows key on your keyboard and press the letter C to open

the Charm menu, and then click the gear icon (Settings).

Step 2 Click Change PC Settings.

Step 3 Click General.

Step 4 Under Advanced Startup, click Restart Now.


User Manual 22

NOTE: In Windows 8.1, the ‘Restart Now’ button has moved to ‘PC Setting -> Update

& Recovery -> Recovery.’


User Manual 23

Step 5 After restarting, click Troubleshoot.

Step 6 Click Advanced Options.


User Manual 24

Step 7 Click Windows Startup Settings.

Step 8 Click Restart.

Step 9 After restarting your computer a second time, choose Disable driver signature

enforcement from the list by typing the number 7 on your keyboard.


User Manual 25

Your computer will restart automatically.

Step 10 After restarting, you will be able to install the ADB drivers normally; however,

Windows will display a warning message. When the warning appears, click Install this

driver software anyway. If you are unfamiliar with installing drivers, check out our

Installing ADB driver tutorial for a step by step guide.

NOTE:

The next time you restart your computer, driver signature

enforcement will be in effect again. You will have to repeat this

process for any new boards. If you have multiple boards to use with

the same computer, we recommend installing the drivers for each one

before you shut down or restart your computer.


User Manual 26

3.1.2 ADB Driver Installation

Step 1 Confirm whether the USB device was found by the system.

Device Manager > 120A > Other devices > FA33_Taurus > Update Driver Software

Step 2 In the Update Driver Software window choose Browse my computer for

driver software.

Step 3 Select Let me pick from a list of device drivers on my computer. Click Next.


User Manual 27

Step 4 Select from your computer

Step 5 In the Update driver software window, click show All Devices and then click

Next.

Step 6 The system is looking for the driver folder. Click Browse.


User Manual 28

Step 7 Select the driver for your OS system. Click Open.

Step 8 Windows Security window will pop up. This message is used to confirm

whether the user wants to install the driver. Select Install this driver software

anyway to continue.


User Manual 29

Step 9 When the installation is successfully completed you will see Android ADB

Interface driver in the Update Driver Software window. Now adb debug can be

carried out.

3.2 Installing Android Debug Bridge (ADB)

For detailed Android Debug Bridge (ADB) information refer to Android Developers

Platform: http://developer.android.com/tools/help/adb.html .

http://developer.android.com/tools/help/adb.html


User Manual 30

Step 1

Decompress adb.zip. Open ADB terminal and move into the adb archive.

ADB Terminal window

Step 2

Connect FA33 motherboard to the computer via USB. FA33 will ask you to confirm

USB debugging. Tap OK.

After ADB connection established, install APP or check system log via adb.


User Manual 31

3.3 Download Image Tool

Download OS Image Tool update guide:

1. Winmate Download Center

http://www.winmate.com.tw/ > Support > Download Center > Multi-touch PPC >

W10FA3S-PCH > OS Image

2. Winmate Partner Portal

http://www.winmate.com.tw/ > Support > Partner Portal > Public Documents >

Panel PC > Multi-Touch HMI > S-Series HMI > FA > OS Image Update Guide

3.4 OTA Update Guide

OTA is a tool which can help you to update OS image. To receive Android OS image

file contact our sales representatives. Once you get the image file follow the

guideline below.

Step 1 Copy image files ota_FA33_X_X_X_X.zip and FA33_X_X_X_X. md5 and to

micro SD card.

Step 2 Insert micro SD card to the slot in the HMI device.

In the APPs menu tap OTA Image Upd.

http://www.winmate.com.tw/



User Manual 32

Step 3 The system is checking OTA File. It may take some time.

Step 4 Tap Update Image


User Manual 33

Step 5 Make sure the file founded by the system is image update file.

Tap OK.

Step 6 Tap OK. Make sure the battery level is at least 50%.


User Manual 34

Step 7 Tap OK.

IMPORTANT:

Do not disconnect the power source!

Do not remove the battery!

Step 8 After update the system will automatically restart.


User Manual 35

3.5 OS Image Update Guide

Step 1 Decompress the archive FSL_MFG_TOOL_WM.zip

Step 2 Go to the directory “FSL_MFG_TOOL_WM\Profiles\MX6Q Linux

Update\OS Firmware\files\android”.

Step 3 Move the following items to one folder: the u-boot-6q.bin, boot.img,

system.img, userdata_img.tar.gz and recovery.img


User Manual 36

Step 4 In FSL_MFG_TOOL_WM folder that you decompressed in Step 1 click

“MfgTool2.exe”.

MfgTool_MultiPanel window pops up.

Step 5 Go to the main APPS screen > Settings


User Manual 37

Step 6 Settings > About tablet

Step 7 Settings > About tablet > Additional system updates


User Manual 38

Step 8 Warning menu pops up. Confirm the system update by clicking YES.

Step 9 Enter the hint number 1655 to confirm the update and click OK.

NOTE:

The location of OTG connector is shown on the picture below:

IMPORTANT:

Assure OTG and power already connected. Do not disconnect the OTG

from the source of power while system is updating.


User Manual 39

Step 10 In the dialog click Yes to shut down and restart the system.

Step 11 After the system reboot you will be able to see the system change.

No Device Connected > HID-compliant


User Manual 40

Step 12 Click Start to upgrade the system.

Step 13 After the successful update the screen is shown as below:

OMFA Motherboard Technical Support Documents

User Manual 41

Technical Support Documents This chapter contains directory to software

development kit.

OMFA Motherboard Technical Support Documents

User Manual 42

Chapter 4: Technical Support Documents

This chapter includes the list of technical support documents and software

developing kit (SDK). If any problem occurs immediately contact us.

4.1 Android SDK

Download Android SDK from Winmate Download Center.

1. Winmate Download Center

http://www.winmate.com.tw/ > Support > Download Center > OPS Module > OMFA

> Development Kit
