openplant water/waste water cck · 2020. 12. 29. · openplant water/waste water cck bentley...
TRANSCRIPT
-
1
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
1
OpenPlant Water/Waste Water CCK
BENTLEY 软件(北京)有限公司
2020/12/21
-
12/21/2020
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
1
目 录
1. 文档版本记录 ......................................................................................................................... 1
2. 安装要求 ................................................................................................................................. 2
2.1 系统要求(推荐配置) ....................................................................................................... 2
2.2 OpenPlant PID ................................................................................................................. 2
2.3 OpenPlant Modeler ......................................................................................................... 3
3. PID 图例说明 .......................................................................................................................... 4
3.1 为水行业增加的设备图例 ............................................................................................. 4
3.2 为水行业增加的管件图例 ............................................................................................. 6
3.3 为水行业增加的仪表图例 ............................................................................................. 9
4. 等级库说明 ........................................................................................................................... 10
4.1 T1 ................................................................................................................................... 10
4.2 UPVCSPEC ...................................................................................................................... 10
5. OPM 参数化设备 .................................................................................................................. 11
5.1 闸门 ............................................................................................................................... 11
5.2 启闭机 ........................................................................................................................... 13
5.3 沉砂器 ........................................................................................................................... 14
5.4 清污机 ........................................................................................................................... 15
5.5 刮泥机 ........................................................................................................................... 16
5.6 排污泵 ........................................................................................................................... 17
5.7 搅拌机 ........................................................................................................................... 18
5.8 鼓风机 ........................................................................................................................... 19
6. OPM 参数化阀门 .................................................................................................................. 20
6.1 微阻缓闭蝶式止回阀 ................................................................................................... 20
6.2 带锁平衡阀 ................................................................................................................... 22
6.3 快开排泥阀 ................................................................................................................... 23
6.4 明杆楔式闸阀 ............................................................................................................... 25
6.5 电磁阀 ........................................................................................................................... 27
6.6 刀闸阀 ........................................................................................................................... 29
-
12/21/2020
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
2
6.7 旋启式止回阀 ............................................................................................................... 30
6.8 升降式止回阀 ............................................................................................................... 32
6.9 球阀与手柄 ................................................................................................................... 34
6.10 活塞式减压阀 ........................................................................................................... 36
7. 执行机构及其他 ................................................................................................................... 39
7.1 D941X 电动执行机构 ................................................................................................... 39
7.2 D943H 电动执行机构 ................................................................................................... 40
7.3 手柄 ............................................................................................................................... 42
7.4 电动刀闸阀 ................................................................................................................... 44
7.5 法兰限位伸缩接头 ....................................................................................................... 48
7.6 不锈钢波纹管 ............................................................................................................... 51
Appendix 1: Spec 数据库中相关表与字段说明 .......................................................................... 53
Appendix 2: China First 使用工具说明 ......................................................................................... 54
-
1
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
1
12/21/2020
1. 文档版本记录
版本 日期 作者 备注 10.08.0051 2020-12-21 单鹏/武博 首次发布
-
2
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
2
12/21/2020
2. 安装要求
2.1 系统要求(推荐配置)
CPU:2GHz X64 Processor 或者更高,四核或者八核,Intel i7-3740QM 同等配置或以上
内存:8G,建议 16G 以上
硬盘:500G 以上,建议系统盘采用 SSD 固态硬盘
显卡:显存 2G 或者更高,NVIDIA Quadro K2000M 系列及同等配置型号以上(支持双
屏优先)
操作系统:Windows 7 X64 专业版以上,建议 Window 10 专业版或企业版
说明:对于台式机,显卡支持双屏显示,同时外配外接显示器将大大提高工作效率
2.2 OpenPlant PID
提前安装 OpenPlant PID Update 8(oppid10080051zh) ,中文版/英文版均可。以中文版为
例。安装后,选择“WWT_WorkSpace”环境。
-
3
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
3
12/21/2020
2.3 OpenPlant Modeler
提前安装 OpenPlant Modeler Update 8(opm10080051zh) ,中文版/英文版均可。以中文版为
例。安装后,选择“WWT_WorkSpace”环境。
-
4
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
4
12/21/2020
3. PID 图例说明
3.1 为水行业增加的设备图例
• 机械计量泵
• 气动泵
• 化学注入隔膜泵
• 立式切碎泵
• 立式涡轮泵
• 潜水泵
• 齿轮泵
• 计量泵
• 往复泵
• 螺旋泵
• S 螺杆泵
-
5
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
5
12/21/2020
• 离心式多级鼓风机
• 离心式单级鼓风机
• 双往复式压缩机
• 离心式压缩机
• 风扇
• 鼓风机
• 空气压缩机
-
6
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
6
12/21/2020
• 水闸
• 滑动门
• 快速闸门
• 起重机
• 回转格栅
• 启闭机
• 撇水器
• 阶梯格栅
• 集油管
• 管式曝气器
• LC 曝气器
• TOS 曝气器
• 板框
• 离心脱水机
• 刮泥机
• 刮油刮泥机
• 冷却塔
• 浆式搅拌机
• 潜水搅拌机
• 浮筒搅拌机
• 自卸卡车
• 纤维球
• 压力溶气罐
• 水锤消除器
3.2 为水行业增加的管件图例
-
7
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
7
12/21/2020
• 水泵阀
• 节流阀
-
8
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
8
12/21/2020
• 排放消音器
• 过滤器
• 火焰阻火器
• 在线静态混合器
• 扩散器
• 带排放过滤器
• 机械清洁过滤器
• 快拆
• 脉冲缓冲器
• 放空到大气
• 蒸发器
• 蒸汽加热器
• 观察孔
• 气隙
• 活接头
-
9
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
9
12/21/2020
3.3 为水行业增加的仪表图例
• 环形密封
• 隔膜密封
• 卫生密封
• 校准柱
-
10
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
10
12/21/2020
4. 等级库说明
修复部分内容
• 所有 MAIN_SIZE, RUN_SIZE 字段公制单位统一不加 mm,不带小数点,如 100, 150…
• 法兰、螺栓、垫片等紧固件 Rating 字段统一使用 PN 制,不使用 Mpa 制,
如 PN16, PN40, PN160,对照关系如下
公称压力 MPa
0.6 MPa 1.0 MPa 1.6 MPa 2.0 MPa 2.5 MPa 4.0 MPa 5.0 MPa 6.4
MPa 10.0 MPa - 15.0 MPa 25.0 MPa 42.0 MPa
公称压力 PN PN6 PN10 PN16 PN20 PN25 PN40 PN50 PN64 PN100 - PN150
PN250 PN420
4.1 T1
安装包附带了名为 T1 的管道等级库作为测试之用,具体项目还需根据项目需求制定相应
的等级库.
4.2 UPVCSPEC
增加了水行业需要的 PVC 管件增加了水行业需要的 PVC 管件,如 GB/T 10002.1-2006
-
11
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
11
12/21/2020
5. OPM 参数化设备
WWT CCK 中新增了水处理相关的设备部件和阀门等,用户可以使用这些设备和阀门进行
建模。对于设备,可到新添加的“WWT Equipment”工具栏中去选取; 对于阀门和执行机
构,需要到相应类别的阀门和执行机构中去选取。
设备的布置使用如下工具,依次为:闸门、启闭机、沉砂器、清污机、刮泥机、排污泵、
搅拌机、鼓风机。
各个设备的布置界面及效果如下:
5.1 闸门
-
12
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
12
12/21/2020
-
13
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
13
12/21/2020
5.2 启闭机
-
14
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
14
12/21/2020
5.3 沉砂器
-
15
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
15
12/21/2020
5.4 清污机
-
16
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
16
12/21/2020
5.5 刮泥机
-
17
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
17
12/21/2020
5.6 排污泵
-
18
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
18
12/21/2020
5.7 搅拌机
-
19
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
19
12/21/2020
5.8 鼓风机
-
20
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
20
12/21/2020
6. OPM 参数化阀门
以下对 WWT CCK 中实现的自定义阀门部分所使用的规范,型号以及在 Open Plant Modeler
中界面的放置等进行详细说明。
6.1 微阻缓闭蝶式止回阀
参照规范《阀门产品样本 下 第 4 版》第 300 页,HH49X 型 PN10~25。
阀门 EC Class 名字 MRSC_BUTTERFLY_CHECK_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“微阻缓闭蝶式止回阀”
进行布置。
-
21
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
21
12/21/2020
布置结果如下所示:
-
22
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
22
12/21/2020
6.2 带锁平衡阀
参照规范《阀门产品样本 下 第 4 版》第 1004 页,SP15F 型 PN10,16。
阀门 EC Class 名字 LOCKED_BALANCE_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“带锁平衡阀”进行布
置。
布置结果如下所示:
-
23
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
23
12/21/2020
6.3 快开排泥阀
参照规范《阀门产品样本 下 第 4 版》第 954 页,JM774X 型 PN6,PN10。
-
24
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
24
12/21/2020
阀门 EC Class 名字 QUICKLY_OPENING_SLUDGE_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数(H 应为阀体中心到顶部的高度,规范有
误)。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“快开排泥阀”进行布
置。
布置结果如下所示:
-
25
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
25
12/21/2020
6.4 明杆楔式闸阀
参照规范《阀门产品样本 上 第 4 版》第 37 页,Z41W 型 PN10。
-
26
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
26
12/21/2020
阀门 EC Class 名字 WEDGE_GATE_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“明杆楔式闸阀”进行布
置。
布置结果如下所示:
-
27
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
27
12/21/2020
6.5 电磁阀
参照规范《阀门产品样本 下 第 4 版》第 990 页,ZSC-16 型。
阀门 EC Class 名字 ELECTRIC_GATE_VALVE。
Spec 表 VLVCNTSC 的 COMP_LEN 列对应了规范中的 L 参数。
-
28
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
28
12/21/2020
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“明杆楔式闸阀”进行布
置。
布置结果如下所示:
-
29
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
29
12/21/2020
6.6 刀闸阀
参照规范《阀门产品样本 上 第 4 版》第 221 页,Z73H 型 PN10。
阀门 EC Class 名字 KNIFE_GATE_VALVE_WAFER。
Spec 表 VALVFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VALVFL 的 OPERATING_HEIGHT
列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“闸阀阀”,并选择“刀闸阀”进行布置。
-
30
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
30
12/21/2020
布置结果如下所示:
6.7 旋启式止回阀
参照规范《石油化工装置工艺管道安装设计手册 第 3 篇 阀门》第 226 页,H44W 型
PN10。
-
31
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
31
12/21/2020
阀门 EC Class 名字 SWING_CHECK_VALVE。
Spec 表 VALVFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VALVFL 的 OPERATING_HEIGHT
列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“止回阀”,并选择“旋启式止回阀”进行布
置。
-
32
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
32
12/21/2020
布置结果如下所示:
6.8 升降式止回阀
参照规范《阀门产品样本 下 第 4 版》第 248 页,H11W 型 PN16。
-
33
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
33
12/21/2020
阀门 EC Class 名字 LIFT_OPERATOR_CHECK_VALVE。
Spec 表 VALVSCSW 的 COMP_LEN 列对应了规范中的 L 参数;表 VALVSCSW 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“止回阀”,并选择“升降式止回阀”进行布
置。
-
34
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
34
12/21/2020
布置结果如下所示:
6.9 球阀与手柄
参照规范《阀门产品样本 上 第 4 版》第 625 页,Q11F 型 PN10~64。
-
35
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
35
12/21/2020
阀门 EC Class 名字 BALL_VALVE_STRAIGHT;执行机构 EC Class 名字 WRENCH_BAR。
Spec 表 VALVSCSW 的 COMP_LEN 列对应了规范中的 L 参数;表 TOPWORKS 的
TOTAL_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“球阀”,并选择“球阀与手柄”进行布置。
-
36
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
36
12/21/2020
布置结果如下所示:
6.10 活塞式减压阀
参照规范《阀门产品样本 下 第 4 版》第 735 页,Y43H 型 PN16。
-
37
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
37
12/21/2020
阀门 EC Class 名字 PISTON_PRESSURE_REDUCING_VALVE。
Spec 表 VLVRELFL 的 COMP_LEN 列对应了规范中的 L 参数,表 VLVRELFL 的 TOP_HEIGHT 列
对应了规范中的 H1 参数,BOTTOM_HEIGHT 列对应 H2 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“泄放阀”进行布置。
-
38
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
38
12/21/2020
布置结果如下所示:
-
39
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
39
12/21/2020
7. 执行机构及其他
7.1 D941X 电动执行机构
参照规范《阀门产品样本 下 第 4 版》第 26 页,D941X 型。
EC Class 名字 ELECTRIC_CUBE_OPERATOR。
Spec 表 TOPWORKS 的 HANDLE_LENGTH 列对应了规范中的 B2 参数, TOTAL_HEIGHT 列对
应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“执行机构类”选择“立方体”,并选择“Electric Cube
Operator”进行布置。
-
40
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
40
12/21/2020
布置结果如下所示:
7.2 D943H 电动执行机构
参照规范《阀门产品样本 下 第 4 版》第 142 页,D943H 型。
-
41
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
41
12/21/2020
EC Class 名字 MOTOR_VALVE_ACTUATOR。
Spec 表 TOPWORKS 的 TOTAL_HEIGHT 列对应了规范中的 H1 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“执行机构类”选择“立方体”,并选择“Motor Valve
Actuator”进行布置。
布置结果如下所示:
-
42
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
42
12/21/2020
7.3 手柄
参照规范《阀门产品样本 上 第 4 版》第 625 页,Q11F 型 PN10~64。
-
43
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
43
12/21/2020
EC Class 名字 WRENCH_BAR。
Spec 表 TOPWORKS 的 TOTAL_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
可以和球阀一同使用,也可以单独使用。
在 Open Plant Modeler 中,“执行机构类”选择“阀门扳手”进行布置。
布置结果如下所示:
-
44
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
44
12/21/2020
7.4 电动刀闸阀
Z973X 型电动刀闸阀制造标准:
结构长度标准:GB/T 12221-2005
连接法兰标准:GB/T 9113
压力温度等级:GB/T 12224-2005
试验检验标准:GB/T 13927-2008
-
45
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
45
12/21/2020
-
46
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
46
12/21/2020
EC Class 名字 MOTOR_OPERATED_VALVE_ACTUATOR_WITH_HAND_WHEEL。
Spec 表 TOPWORKS 的 TOTAL_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“执行机构类”选择“电动机”进行布置。
布置结果如下所示:
-
47
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
47
12/21/2020
-
48
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
48
12/21/2020
7.5 法兰限位伸缩接头
VSSJA 型技术参数:
-
49
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
49
12/21/2020
EC Class 名字 PIPE_COUPLING_STRETCH。
Spec 表 MISC_FIT 的 COMP_LEN 列对应了规范中的 L 参数,FIX_PART_LENGTH 对应 L1 参
数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“接头类”选择“接头”,并选择“Pipe Coupling Stretch”进
行布置。
-
50
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
50
12/21/2020
布置结果如下所示:
-
51
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
51
12/21/2020
7.6 不锈钢波纹管
简介:
金属软管(简称软管)是现代工业管路中一种高品质的柔性管道。它主要由波纹管、网套
和接头组成。它的内管是具有螺旋形或环形波形的薄壁不锈钢波纹管,波纹管外层的网
套,是由不锈钢丝或钢带按一定的参数编织而成。软管两端的接头(法兰)是与客户管道
的接头(法兰)相配的。
EC Class 名字 FLEXIBLE_METAL_TUBING。
Spec 表 PIPE 的 MAIN_SIZE 列为管径大小。Spec 表说明参见附录。
在 Open Plant Modeler 中,“管道类”选择“管段”进行布置。
-
52
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
52
12/21/2020
左键画管,用户确定长度,右键结束后布置结果如下所示:
-
53
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
53
12/21/2020
Appendix 1: Spec数据库中相关表与字段说明
新建阀门等管件的等级数据主要涉及 Spec 数据库中的阀门表如 VLVCNTFL,VALVFL 和
VALVSCSW,执行机构表 TOPWORKS,其他还有 MISC_FIT 和 PIPE 表。下面就其中部分公共
的列做详细说明。
列名 描述
MEAS_UNITS ME 公制 IM 英制
CATALOG 标准手册/规范的名字
TAG 主型号名字
LONG_DESCR 长描述
WEIGHT_DRY 干重
PIPE_OD_M 入口外径
CTR_END_M 中心距 mainport 长度
CTR_END_R 中心距 runport 长度
COMP_LEN 长度
OPERATOR_HEIGHT 阀门高度
HANDWL_OD 手轮外径
HANDWL_LEN 手轮长度
OPERATOR 执行机构的 EC CLASS 名字
RUN_SIZE 出口长度,不填则与 MAIN_SIZE 一样
REV 版本号
END_COND_1 入口连接方式:例如 FF/SCF/RF
END_COND_2 出口连接方式,不填则同 END_COND_1
END_COND_3 分支连接方式,不填则同 END_COND_1
MAIN_SIZE 公称直径,公制用 mm 单位
FACING_1/2/3 法兰连接时指定端面类型:FF/RF 等,螺纹连接的不填
SCHEDULE 壁厚等级
RATING 压力等级如 PN10
MATERIAL 材料
MANU_FACT 供应商
OPTIONCODE 如使用 Use Spec Defaults,则值 1 将此数据设为默认,比非 1 的优先
SYS_ID 内部使用,不需填写
-
54
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
54
12/21/2020
Appendix 2: China First使用工具说明
新增 China First 属性导入工具,可通过此工具,批量添加/修改 OpenPlant 中设备/管线
属性。详细操作方法,请见帮助文档。
以下为部分截图
使用“导入属性”工具,用户可以从 Excel 文件导入属性数据,批量修改管线/设备等对象
属性,方便批量修改。使用方法如下:
启动 OpenPlant Modeler,打开需要导入的.dgn 文件,选择“China First”的 ”导入属性” 。
结果如下:
-
55
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
55
12/21/2020
-
56
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
56
12/21/2020
WWT Workspace CCK 使用说明