operating & parts manual - amity technology · operating & parts manual active depth...
TRANSCRIPT
OPERATING &
PARTS MANUAL
ACTIVE DEPTH CONTROL
2800 7TH Avenue North Fargo, ND 58102
Phone: (701) 232-4199 Fax: (701) 234-1716 www.amitytech.com
P/N 301285-REVB
Figure 1 ‐ HOME SCREEN
A – Joystick Selection and Activation Button
Signifies the PTO is not engaged and the joystick is inactive. Upon initial system power
up, press once for the JOYSTICK FUNCTION SELECTION SCREEN (Figure 2) to appear.
Signifies the PTO is engaged, but joystick remains inactive. Press once to activate the
joystick and the button turns Green.
PTO is engaged and joystick is activated. Press once to deactivate joystick (Back to Red).
NOTES:
Upon each initial system power‐up and PTO engagement, the button will begin as Red
until the initial joystick activation (Button to Green). After the initial activation (Red to
Green), the button will toggle between Blue (Inactive) and Green (Active) based on
whether the PTO is engaged.
After the initial power up & joystick activation, the button, no matter the color (Blue,
Red or Green), will need to be held for 3 seconds for the JOYSTICK FUNCTION SELECTION
SCREEN (Figure 2) to appear.
TROUBLESHOOTING TIP: If PTO is engaged and button remains Blue, check PTO sensor. The
connections should be secure and proximity of the sensor to the collar should be within a 1/8”.
1
Figure 2
Press any
it returns
SCREEN (
will rema
If the PTO
purposes
the joyst
turn Gree
If the PTO
joystick a
In refere
they use
of the fu
(Figure 1
In refere
they use
orientati
changes
deactivat
re‐engag
PLEASE N
work the
is part of
2 – JOYSTIC
y blue butto
s to the HOM
(Figure 1) sh
ain the same
O is engaged
s, the joystic
ick is inactiv
en.
O was not en
activation an
nce to joyst
the same 4
nctions are o
– F) by 0.2 i
nce to joyst
the same 4
on of the fu
the digging
tes the “AUT
ged.
NOTE: The f
e same as tou
f a dual func
1
3
CK FUNCTI
n as shown
ME SCREEN (
hows the cur
e until anoth
d while maki
ck activation
ve. To re‐act
ngaged whil
nd selection
tick configur
functions (“
opposite. E
inches.
tick configur
functions (“
nctions are o
depth witho
TO” mode, w
functions on
uching the s
tion on the “
ION SELEC
in 1, 2, 3 or
(Figure 1). T
rrent joystick
her selection
ing a new jo
and selectio
tivate the joy
e making a n
button (Figu
rations 1 and
“AUTO”, “EN
Each click tow
rations 3 and
“AUTO”, “EN
opposite. Ea
out altering t
which contro
the joystick
creen. The
“RAISE HITC
CTION SCRE
4 to select a
The diagram
k configurati
is made.
ystick config
on button (F
ystick, simpl
new joystick
ure 1 – A) wi
d 2 Both of
ND ROW”, “+
ward the “+”
d 4 Both of
ND ROW”, “L
ach click tow
the target di
ols depth and
k (“AUTO”, “
only differen
H” Button o
EEN
a joystick con
in the uppe
ion. The joy
guration sele
Figure 1 ‐ A)
ly press the
k configurati
ill remain Bl
f these selec
+”, “‐“); howe
”or “‐“chang
these select
LOWER”, “RA
ward “RAISE”
igging depth
d side to sid
END ROW”,
nce is the “E
on the screen
nfiguration.
er left corner
ystick configu
ection (1, 2,
will return t
Red button
on selection
ue.
ctions will fu
ever, notice
ges the targe
tions will fun
AISE“); howe
” or “LOWER
h (Figure 1 –
e leveling, u
“+”, “‐“, “LO
END ROW” f
n. (See “D” –
2
After select
r of the HOM
uration show
3, 4), for saf
to Red mean
once and it
n (1, 2, 3, 4),
nction simila
the orienta
et digging de
nction simila
ever, notice
R”, tempora
F). This
until “AUTO”
OWER”, “RA
unction Butt
– Next Page
4
tion,
ME
wn
fety
ning
will
the
ar as
tion
epth
ar as
the
rily
” is
ISE ”)
ton
)
2
Figure 1 ‐ HOME SCREEN
B – Wand Depth Indicators The wand depth indicators show the
instantaneous values of the left and right hand wands. These values are used to
achieve the target depth (Figure 1 – F).
PLEASE NOTE: If either the LH or RH indicators lose complete movement or do
NOT appear to be tracking the target depth (Figure 1 – F), re‐calibrate the wands.
(See “M” – Page 7) If the problem continues after re‐calibration, check rotary
position sensors for damage.
C‐ “LOWER HITCH” Button This button lowers the hitch incrementally. It functions in two
different increments, small and large, dependent on whether the PTO is engaged. If the PTO is
not engaged (non‐harvesting) and the button is pressed, the hitch cylinder will move smoothly
in a larger increment. If the PTO is engaged (signifying harvesting) and the button is pressed,
the hitch cylinder will move a small increment each time the button is pressed and will
deactivate the “AUTO” mode.
D‐ “RAISE HITCH/END ROW” Button This button has dual functions. This button raises
the hitch incrementally. And, if this button is held for 3 or more seconds, it goes to “END
ROW” mode and raises harvester to its maximum height. PLEASE NOTE: It works on the same
increment and operating premises described above for the “LOWER HITCH” Button.
3
Figure 1 ‐ HOME SCREEN
E – “–” Button This button decreases the target digging depth in increments of 0.2 inches.
F – Digging “Depth” Indicator This indicator shows the target digging depth of the ADC
unit when it is run in “AUTO” mode. Currently, Figure 1 – F shows a current target depth of 3.4.
PLEASE NOTE: The target digging depth is an arbitrary number. The default Wand setting from
factory will attempt to set target digging depth close to what the actual digging depth
measures. By adjusting the wand height (See “Wand Adjustment” – Page 12), you can change
the relationship between the target digging depth and actual digging depth to your satisfaction.
G – “+” Button This button increases the target digging depth in increments of 0.2 inches.
H – “AUTO” Button This button initiates the “AUTO” mode. It turns Green when engaged.
I – Axle Cylinder Height Indicators The Orange bars on the left and right indicate the
instantaneous height of the axle cylinders. The axle cylinders will vary +/‐ 2 inches from the
axle cylinder setpoint. The maximum differential between the cylinders equals 4 inches.
Pressing either of the axle cylinder graphics (Figure 1 – I) will put you into the AXLE CYLINDER
SETPOINT SCREEN (Figure 3 – Next Page)
4
Figure 3
This scre
HOME SC
Select yo
After a se
Amity M
cleaning
elevation
rear jum
model.
Amity M
PLEASE N
3 – AXLE CY
en appears a
CREEN. (Figu
our desired s
election is m
odel 2700 1
of sugar bee
n angle, whic
p chain/grab
odel 2500 8
NOTE: Do N
YLINDER S
after you to
ure 1 – I).
setting by sim
made, it will r
12‐Row Harv
ets. Selectin
ch means th
brolls. All se
8‐Row Harve
OT use setti
SETPOINT S
uch either o
mply touchin
return to the
vester Settin
ng a higher v
e beets will
elections (2”,
ester Setting
ngs 2” or 8”
SCREEN
of the axle cy
ng one of the
e HOME SCR
ng The typic
value (4”, 6”,
be subjecte
, 4”, 6” or 8”
g Amity reco
” for the Mod
ylinder heigh
e four displa
REEN (Figure
cal (default)
, or 8”) resu
d to a highe
”) are availa
ommends th
del 2500 8‐R
ht indicators
ayed boxes (
e 1).
setting is 2”
lts in a highe
er angle of tr
ble for the u
he default se
Row Harvest
s shown on t
(2”, 4”, 6” or
” for standar
er average
ravel over th
use on this
etting to be a
ter.
the
r 8”).
rd
he
at 4”.
5
Figure 1 ‐ HOME SCREEN
J – Options Screen Button This button displays the OPTIONS SCREEN (Figure 4‐Next Page).
K – Status Screen Button This button displays the STATUS SCREEN (Figure 6). If there is a
problem with any of the 6 status indicators, then the Green checkmark is replaced by a Red X.
PLEASE NOTE: If a Red X is displayed, the system will NOT be allowed to go into “AUTO” mode.
6
Figure 4
In the OP
making a
promptly
L – “Dep
minimum
side of th
depth co
low a set
The setti
free to ch
field con
M – Cal
SCREEEN
fully exte
PLEASE N
Q
K
L
W
4 – OPTION
PTIONS SCRE
any changes.
y returns you
pth Sensit
m sensitivity
he scale), yo
ontrol. Too h
tting will res
ng you choo
hange it at a
ditions.
librate Wa
N (Figure 5) a
ended (use “
NOTE: Amity
Q
K
L
W
NS SCREEN
EEN (Figure 4
. After revie
u to the HOM
ivity” Slide
(on the left
u will be abl
high a setting
ult in minim
ose will stay
any time, and
ands “ZERO
appear. Cali
“END ROW”)
y recommen
N
4), you can v
ew, simply se
ME SCREEN
er By choos
side of the s
le to determ
g will result
mal, slow reac
fixed even w
d your partic
O” Button
brate the wa
) and let the
nds that calib
R
view the cur
elect the “HO
(Figure 1).
sing a slider
scale) and th
mine the resp
in a fast, po
ction speeds
when the po
cular selectio
This button
ands only wh
wands natu
bration occu
rrent setting
OME” butto
position som
he maximum
ponsiveness
ssibly jerky
s by the hitc
ower is turne
on is a matt
n makes the
hen the harv
urally hang a
urs upon eac
s at any time
n (Figure 4 –
mewhere be
m sensitivity
of the harve
response by
ch.
ed off to the
er of prefere
CALIBRATE W
vester front
against the st
ch initial pow
P
e without
– Q), which
etween the
(on the righ
ester’s active
y the hitch. T
unit. You a
ence and giv
WANDS
hitch cylind
tops.
wer‐up.
O
M
t
e
Too
re
ven
er is
O
N
M
7
Figure 5
S – “YES
T – “NO
settings a
S
5 – WAND
S” Button
O” Button
are affected
S
CALIBRAT
Press this b
Press this bu
.
TION CONF
button to cal
utton to avo
FIRMATION
ibrate the w
oid calibratin
N SCREEN
wands.
ng the wands. No previoous calibrati
T
on
8
Figure 4
N – Axle
maximum
desires to
cylinder
O – Axle
minimum
cylinders
on the H
P – Bee
Q – Hom
R – Bac
backlight
W – “Au
“End Row
raising its
cylinders
of 10”. T
4 – OPTION
e Override
m height of 1
o raise the a
height indica
e Override
m height of 0
s. The chang
OME SCREE
p Volume
me Button
klight Inte
t.
uto Axle” B
w” function.
self to the m
s will equaliz
The “Auto A
Q
K
L
W
NS SCREEN
e Maximum
10”. (Deactiv
axle cylinder
ators on the
e Minimum
0”. This can
e in axle cyli
N (See Figur
Slider Thi
n Press this
ensity Slide
Button Thi
When the “
maximum he
ze to the cur
Axle” button
N
m Button
vates “AUTO
s. The chan
e HOME SCR
m Button
be done any
inder height
re 1 – I).
s slider chan
button to re
er This slide
is button allo
“End Row” b
ight using th
rent set‐poi
is active wh
R
This button
O” mode) Th
ge in axle cy
EEN (See Fig
This button
y time the o
will be show
nges the “be
eturn to the
er changes th
ows for the
button is eng
he hitch cylin
nt (Figure 3)
en the butto
raises the re
his can be do
ylinder heigh
gure 1 – I).
lowers the
perator desi
wn in the ax
eep” volume
HOME SCRE
he “brightne
option of an
gaged, in ad
nders, both
) and procee
on remains G
ear axle cylin
one any time
ht will be sho
rear axle cyl
ires to lowe
xle cylinder h
e of each key
EEN (Figure 1
ess” of the s
n additional
dition to the
the left and
ed to their m
Green.
P
nders to the
e the operat
own in the a
inders to th
r the axle
height indica
y press.
1).
creen’s
function to t
e harvester
right axle
maximum he
eir
tor
axle
eir
ators
the
ight
O
N
M
9
Figure 6 – STATUS SCREEN (All Good)
U – Status Indicators “Good” appears in Green. “Fault” appears in Red.
V – Sensor Descriptions
Left Wand – Indicates Power is supplied to the LH Rotary Position sensor.
It does NOT indicate a damaged/broken Rotary Position Sensor.
Right Wand – Indicates Power is supplied to the RH Rotary Position sensor. It does NOT
indicate a damaged/broken Rotary Position Sensor.
Left Axle Cylinder – Indicates Power is supplied to the LH axle cylinder sensor.
Right Axle Cylinder – Indicates Power is supplied to the RH axle cylinder sensor.
Cylinder Discrepancy – Indicates the axle cylinder differential has exceeded the
maximum of 4” ‐‐ OR – The differential has exceeded 2” above or below the axle
setpoint.
Wand Discrepancy – Indicates the LH and/or RH wand depth indicators are not tracking
to the target digging depth.
VU
10
Figure 7
U – Stat
PLEASE N
function
HOME SC
is display
7 – STATUS
tus Indicat
NOTE: A fau
ing in Auto.
CREEN (Figu
yed, the syst
S SCREEN (
tor “Good”
ult in any of t
It is import
re 1). A faul
em will NOT
(Fault Show
appears in G
the six senso
tant to moni
lt will make t
T be allowed
U
wing)
Green. “Fau
ors shown w
tor the Statu
the Green c
d to go into “
ult” appears
will prevent t
us Screen bu
heckmark a
“AUTO” mod
in Red.
the ADC con
utton (Figure
ppear as a R
de.
ntroller from
e 1 – K) on th
Red X. If a R
m
he
Red X
11
HYDRAULICS:
The modulated valve can be run either open or closed center. The valve comes
standard with a closed center plug.
Provide the modulated valve 16‐18 gallons per minute (GPM) to run the ADC system.
The case drain line comes from the rear valve section. This line needs to be plugged into
the tractor’s case drain. There is a relief valve in this loop to ensure the valve will be
relieved in the case that the line becomes disconnected from the tractor for any reason.
Wand Adjustment:
Loosen bolts A and use adjustment rod (bolts B) to adjust the height of the wands. (Ref
Figure 8 below).
Figure 8 – Wand Height Adjustment
Note: From factory, dimension C is 5.25 inches.
Tractor Cab Connections:
Use the stripped Black (Ground) and Red (Positive) wire from the tractor harness
provided and connect to the tractor battery power.
12
Rotary Position Sensor:
Figure 9 – Sensor Installation Steps
Ensure Wands are against the stops. Slide sensor onto Peg in orientation shown
Rotate sensor counter clockwise (CCW)
Install screws and tighten.
13
538
36
8
6
112
3 1
3
4
8
7
6
2
7
8
7
13
25
10
11 16
16
30
29
20
26
21
19
24
8
22
18
14
37
2818
17
9
1527
32
23
17 31
12
3736
33
39
M4306-E
STEP 3ROTATECOUNTER CLOCKWISE
SLIDE SENSOR ONTO
STOPAGAINST WANDS AREMAKE SURE
SHAFT
STEP 1
STEP 2
STEP 4INSTALL SCREWSAND TIGHTEN
14
ITEM PART NO. DESCRIPTION QTY
1 63661 WLDMT-MOUNTING BRACKET 12 52654 BUSHING-FLANGE 23 300214 WLDMT-MOUNTING SUPPORT ADC NARROW 24 63664 BOLT-HEX: .75 X 14.00 NC GR5 ZP 15 1013537 NUT-CENTERLOCK: .75 NC ZP 16 53984 U-BOLT 1/2 X 7 X 6 X 7 27 1011581 WASHER-LOCK: .50 ZP 88 1011577 NUT-HEX: .50 NC ZP 109 300216 WLDMT-ADC ARM 8R 1
73474 WLDMT-ADC ARM 12R10 62882 WLDMT-TIGHTENER 11.125" ZP 111 1011578 NUT-HEX: .63 NC GR2 ZP 212 1011609 BOLT-HEX: .50 X 2.00 NC GR5 ZP 413 1011584 WASHER-FLAT: SAE .50 ZP 414 300218 WLDMT-ADC MAIN 8R/12R 115 73490 PLATE-ADC BOLT EYELET 116 73491 U-BOLT .375 X 3.00 X 3.063 X 3.000 417 1011586 WASHER-LOCK: .38 ZP 1118 1011576 NUT-HEX: .38 NC GR2 ZP 1119 56939 BUSHING-BRONZE 220 301244 SHAFT-ADC B 8R/12R 121 300228 PLATE-WAND SENSOR SIDE 122 73475 WLDMT-WAND SPRING SIDE 123 301258 BOLT-HEX: .31 X 2.25 NC GR8 ZP 124 1030700 NUT-TOPLOCK: .31 NC GR5 ZP 125 52306 BOLT-EYE 126 53159 SPRING 127 73487 SHAFT-ADC A ZP 128 73489 BAR-ADC PIN 129 300224 WLDMT-ADC SENSOR HOUSING 8R/12R 130 1016362 BOLT-CRG: .38 X 1.25 NC GR5 ZP 331 1011660 BOLT-CRG: .50 X 1.50 NC GR5 ZP 232 1027461 NUT-TOPLOCK: .50 NC GR5 ZP 233 1011748 ZERK-GREASE: .25UNF STRAIGHT 234 73492 SENSOR-ROTARY POSITION (JD: AH233087) 135 1011304 SCREW-MACHINE RND SLT #10-32 X 1.25 236 301058 SNAP-RING 1.250" 137 55206 BUSHING-MACH: 1.25 NR 14GA 1 OR 238 301267 ROD-WAND LOCK 139 1029164 PIN-HAIR: .19 X 3.00 ZP 1
ACTIVE DEPTH CONTROL WANDS
15
11
8
95
3
5
76
4
210
3
1
1
1
3
7
3
12
3
M4291-A 16
ITEM PART NO. DESCRIPTION QTY
1 301029 WLDMT-SUPPORT VALVE (12R) 2301042 WLDMT-SUPPORT VALVE (8R)
2 64244 U-BOLT: .375 X 5.13 X 8 X 5.13 (12R) 23 1016999 NUT-TOPLOCK: .38 NC GR5 ZP 124 301028 PLATE-MOUNT VALVES ADC 15 1011600 BOLT-HEX: .38 X 1.00 NC GR5 ZP 86 73423 VALVE-MODULATED 3-BANK 17 1011828 WASHER-FLAT .38 ZP 68 73426 VALVE-DUAL COUNTER BALANCE 19 1011285 BOLT-HEX: .31 X 2.00 NC 210 1030700 NUT-TOPLOCK: .31 NC GR5 ZP 211 301045 BAR-BOLTING (8R) 212 1021757 BOLT-HEX: .38 X 5.00 NC GR5 ZP (8R) 4
ACTIVE DEPTH CONTROL HYDRAULIC COMPONENTS
17
6
M4292-B
7
1
14
14
10
1
14
22
5 414
12412
202
1
1
14
14
16
17
17
HITC
H C
YLIN
DER
TO T
OP
OF
LH
HITC
H C
YLIN
DER
TO B
OTT
OM
OF
LH
HITC
H C
YLIN
DER
TO B
OTT
OM
OF
RH
TO T
OP
OF
RHH
ITCH
CYL
IND
ER
11
1615
1
2
82
6
33
524
14
24
19
18
9
7
2
15
13
25
13
25
23
2
121
21
21
18
ITEM PART NO. DESCRIPTION QTY
1 56226 FTG-ADAPTER: 8MB-8MJ 102 57668 FTG-ELBOW: 8MJ-8FJX-90 83 57663 FTG-ELBOW: 8MJ-8FJX-45 24 63015 FTG-TEE: 8MJ-8FJX-8MJ 25 66603 FTG-TEE: 8MJ-8MJ-8FJX 26 37705 HOSE: .50 X 128 8MB-8FJX 47 64263 HOSE: .50 X 011 8JFX-8FJX 28 73593 FTG-PLUG: 4MB 19 301245 FTG-ADAPTER: 4MB-6MB 110 301246 FTG-TEE: 6FB-6MB-6MJ 111 73595 HOSE: .38 X 140 8MB-6FJX 112 65901 FTG-ELBOW: 10MB-8MJ90 113 35770 HOSE: .50 X 52 8FJX-8FJX 214 58560 FTG-ELBOW: 8MB-8MJ-90 715 73594 HOSE: .38 X 228 8FJX-8FJX (12R) 2
301037 HOSE: .38 X 192 8FJX-8FJX (8R)16 69737 HOSE: .38 X 240 8JFX-8FJX (12R) 2
301038 HOSE: .38 X 206 8FJX-8FJX (8R)17 73421 CYLINDER-HYD 4 X 10 10-3000-0° ADC 2
73629 SEAL KIT-CYL 4 X 10 (73421)18 73423 VLAVE-MODULATED 3-BANK 119 73426 VALVE-DUAL COUNTER BALANCE 120 301016 VALVE-CHECK: 10MB-10FB 5000 PSI 121 301018 VALVE-CASE DRAIN RELIEF 122 69119 FTG-CASE DRAIN 3/8 FLAT FACE 1
36290 PIONEER TIP 8010-15P (#8 ORB)23 36290 PIONEER TIP 8010-15P (#8 ORB) 424 58515 FTG-ELBOW: 8MB-8MJ-45 225 1015221 HOSE: .50 X 040 8FJX-8FJX (12R) 2
57676 HOSE: .50 X 31 8FJX-8FJX (8R)
ACTIVE DEPTH CONTROL HYDRAULICS
19
2
1
23
6
1
23 22
REAR STRUT/AXLE RH M4321-A
19
18
10 21
20
6
12
1
6
2
4
1313
5HITCH RH
82
7
3
16
2
11
15
92
2
1
17
REAR STRUT/AXLE LH
17
161414
1
14
12
14
4
25
5
15
3
1414
7
24
25
HITCH LH
14
24
20
ITEM PART NO. DESCRIPTION QTY
1 56226 FTG-ADAPTER: 8MB-8MJ 102 57668 FTG-ELBOW: 8MJ-8FJX-90 83 57663 FTG-ELBOW: 8MJ-8FJX-45 24 63015 FTG-TEE: 8MJ-8FJX-8MJ 25 66603 FTG-TEE: 8MJ-8MJ-8FJX 26 37705 HOSE: .50 X 128 8MB-8FJX 47 64263 HOSE: .50 X 011 8JFX-8FJX 28 73593 FTG-PLUG: 4MB 19 301245 FTG-ADAPTER: 4MB-6MB 110 301246 FTG-TEE: 6FB-6MB-6MJ 111 73595 HOSE: .38 X 140 8MB-6FJX 112 65901 FTG-ELBOW: 10MB-8MJ90 113 35770 HOSE: .50 X 52 8FJX-8FJX 214 58560 FTG-ELBOW: 8MB-8MJ-90 715 73594 HOSE: .38 X 228 8FJX-8FJX (12R) 2
301037 HOSE: .38 X 192 8FJX-8FJX (8R)16 69737 HOSE: .38 X 240 8JFX-8FJX (12R) 2
301038 HOSE: .38 X 206 8FJX-8FJX (8R)17 73421 CYLINDER-HYD 4 X 10 10-3000-0° ADC 2
73629 SEAL KIT-CYL 4 X 10 (73421)18 73423 VLAVE-MODULATED 3-BANK 119 73426 VALVE-DUAL COUNTER BALANCE 120 301016 VALVE-CHECK: 10MB-10FB 5000 PSI 121 301018 VALVE-CASE DRAIN RELIEF 122 69119 FTG-CASE DRAIN 3/8 FLAT FACE 1
36290 PIONEER TIP 8010-15P (#8 ORB)23 36290 PIONEER TIP 8010-15P (#8 ORB) 424 58515 FTG-ELBOW: 8MB-8MJ-45 225 1015221 HOSE: .50 X 040 8FJX-8FJX (12R) 2
57676 HOSE: .50 X 31 8FJX-8FJX (8R)
ACTIVE DEPTH CONTROL HYDRAULICS
21
M4309-B
1
2
22
ITEM PART NO. DESCRIPTION QTY
1 73627 PILOT VALVE-MODULATED VALVE 6301017 SEAL KIT -PILOT VALVE ADC (73627)
2 73425 PLUG-CAVITY CLOSED CENTER #12 1301243 PLUG-CAVITY OPEN CENTER #12 (OPTIONAL)
*NOTE: VALVE COMES STANDARD WITH CLOSED CENTER PLUG
MODULATED 3-BANK VALVE #73423
23
23
10 9 8
7
48 3
1
35
20
18
17
19
16
15
2
14
21
22
6
M4307-A
3
13
12
24
24
ITEM PART NO. DESCRIPTION QTY
1 301046 PLATE-MNT CONTROL BOX ADC 12 64244 U-BOLT: .375 X 5.13 X 8. X 5.13 (12R) 23 1016999 NUT-TOPLOCK: .38 NC GR5 ZP 54 301010 ASSY-CONTROL BOX & PCB ADC 15 1014728 SCREW-#10-24 NC GR2 ZP 46 1026591 NUT-K-LOCK: #10-24 NC GR2 ZP 47 301036 PLATE-SHIELD ADC 18 1011828 WASHER-FLAT .38 ZP 49 1011586 WASHER-LOCK: .38 ZP 210 1011576 NUT-HEX: .38 NC GR2 ZP 211 301023 MONITOR-SCREEN ADC (NOT SHOWN) 112 301035 PLATE-BRACKET ADC MONITOR 113 1016362 BOLT-CRG: .38 X 1.25 NC GR5 ZP 114 301045 BAR BOLTING (8R) 215 1021757 BOLT-HEX: .38 X 5.00 NC GR5 ZP (8R) 416 301024 BRACKET-PTO SENSOR ADC 117 64388 WLDMT-SPLIT COLLAR 1.75" 118 301014 SENSOR-PTO ADC 119 1011595 BOLT-HEX: .25 X .75 NC GR5 ZP 120 1013240 NUT-NYLOCK: .25 NC ZP 121 1011610 BOLT-HEX: .50 X 2.50 NC GR5 ZP 122 1014443 WASHER-FLAT: .50 ZP 123 1027461 NUT-TOPLOCK: .50 NC GR5 ZP 124 301151 ASSY-JOYSTICK & ENCLOSURE 1
ACTIVE DEPTH CONTROL ELECTRONICS
25
M4308-B
3
3
4
657
81
2
2
26
ITEM PART NO. DESCRIPTION QTY
1 301011 HARNESS-ADC HRV 12R 1301015 HARNESS-ADC HRV 8R
2 301020 HARNSS-ADC POTENTIOMETER 23 73509 HARNESS-CYL SENSOR CONNECTOR 24 301152 HARNESS-ADC TRACTOR 15 300249 P-CLIP .38" X .313" 46 1016362 BOLT-CRG: .38 X 1.25 NC GR5 ZP 47 1011828 WASHER-FLAT: .38 ZP 48 1016999 NUT-TOPLOCK: .38 NC GR5 ZP 4
ACTIVE DEPTH CONTROL ELECTRICAL SCHEMATIC
27