our mission is to combat the spread of infectious diseases through a family of comprehensive,...
TRANSCRIPT
Our mission is to combat the spread of infectious diseases through a family of comprehensive, cost-effective, and
environmentally safe solutions.
AeroClave, LLC
Facility, Vehicle, and Equipment Decontamination Solutions
2003-2006• Decontamination of large aircraft
• ACER/ECBC validation work (Air Cabin Environmental Research/Edgewood Chemical Biological Center)
• Harvard viral studies
2006-2007
• CAMI 747 and rail car work (Civil Aeronautical Medical Institute)
2007-2011
• AFRL/AMC TESTS (Air Force Research Lab/Air Mobility Command)
• Complete kill of anthrax simulant through entire aircraft with no damage to aircraft
• Multiple tests – 0 failures
• Beat time-to-kill estimates by over 50%
History of AeroClave
History of AeroClave (cont.)
2008-2009• Development of a Portable Asset
Decontamination System (PADS) in Winter Park, FL
• 30’, 60’ or 100’ chamber configuration
• EMS, fire and law enforcement use this chamber to sterilize their vehicles
2009-2014
• Development of Room Decontamination System (RDS)
• Sterilizes rooms up to 8,000 cubic ft.
• Simply move from room to room
• Development of the Hydra System for building integration
• Development of Ambulance Decontamination System (ADS)
AeroClave Process
• AeroClave solution is evenly applied onto surfaces in two different ways.
• Hand-applied* – for spot-treating and quick decontamination of high-contact areas
• Fogging – for total decontamination of desired treatment area
Hand-applied method* Fogging method
*Use of PPE may be necessary depending on solution being used
Pulsed Application Process(Fogging)
1. Injection Phase: In this phase, the decontamination solution is aerosolized and applied evenly to the treatment area. A typical injection phase will last anywhere from 10-30 minutes, depending on the size of the treatment area.
2. Dwell Phase: Once the injection phase has completed, the treatment area is allowed to sit in a dwell period for a minimum of five minutes. The dwell period gives the aerosolized solution an opportunity to evenly distribute throughout the treatment area, ensuring full coverage on all surfaces.
3. Aeration Phase: The aeration phase is when the solution is removed from the treatment area. This can be done in various ways; reenergizing the facility HVAC, providing external ventilation, promoting air circulation, etc. The solution will also naturally break itself over a period of time, if none of these aeration options are available,
Room Conditioning
Injection Dwell Aeration
• Injection time is typically 5-30 minutes (depending on size of space)
• Much faster than most other technologies
• Dwell cycle time is typically 5-10 minutes
• Many other technologies must reach micro-condensation before going into dwell
• Aeration is dependent on HVAC system or exterior ventilation
• Average Total Cycle Time (start to finish) is about 45 minutes
Typical AeroClave Cycle
System Information
RDS 6110ADS RDS 3110
Room Decontamination System
RDS 3110
• Rugged and Lightweight – 45 lbs.
• Can effectively treat spaces up to 600 ft2
• Fast:
• Average turnaround of a patient room is around 45 minutes
• Average turnaround of an ambulance inside and out is less than 30 minutes
• Average turnaround of an ambulance patient compartment is less than 15 minutes
• Versatile – can be operated in either a fogging or hand-applied method.
• Simple to use – minimal operator training required
• Two unit variations:
• 2 Fixed Heads and 1 Port (Shown)
• 3 Ports
RDS 3110 shown with AeroClave Portable
Applicator (APA)
• 3 Port Variation:
• Can be used as either a remote head fogger or manually hand-sprayed*
*Use of PPE may be necessary depending on solution being used
Room Decontamination System
RDS 6110
• Portable
• Can effectively treat spaces up to 1,500 ft2
• Fast:
• Average turnaround of a patient room is around 30 minutes
• Average turnaround of an operating room is less than 60 minutes
• 4 fixed spray heads and 2 ports
• Fully customizable facility programming
• Facility and asset management tracking software
• Simple to use – minimal training required
• Versatile – can be operated in either a fogging or hand-applied method.
RDS 6110 shown with AeroClave Portable Applicators (APA)
Room Decontamination System
RDS 6110
RDS 3110 and 6110 Applications
• Surgical suites, in and out-patient
• Physician offices and health clinics
• Patient, diagnostic, and procedural rooms
• Research facilities
• Locker rooms and gymnasiums
• Local, state, and federal assistance offices
• Educational facilities from pre-school to college
• Veterinary hospitals and animal shelters
• Law enforcement offices, jails, and holding cells
• Food service and preparation areas
• Cruise ships
• Hotels
Ambulance Decontamination System (ADS)
• Fully integrated patient-compartment system
• Fully automated operation
• Can be operated in-station or on the road
• Fast – average cycle time 15 minutes
• Management tracking software
Ambulance Decontamination Port (ADP)
• Can be installed in either rooms or vehicles
• Eliminates excess manual labor and exposure in contaminated areas
• Ensures consistent operation and results
• Allows for one system to decontaminate up to 3 or 6 different rooms or vehicles simultaneously
• Can be flush mounted (left) or mounted with optional pig tail (above) for access
• Compatible with all AeroClave systems
• Cost effective
• Easy to install
Ambulance Decontamination Port (ADP)
Ports connect to spray heads that are permanently mounted in the treatment area
AeroClave Portable Applicator (APA)
• Accessory for use with all AeroClave systems
• 25’ cable with SmartPort connector
• Allows for both manual hand-application or remote-head fogging
• Smart switch located in mounting point notifies AeroClave system of intended APA use
• Hand-application is ideal for:• Exterior settings• Individual pieces of equipment• Quick spot-treatment on high contact
surfaces
• Remote-head fogging is ideal for:• Expanding the treatment footprint of
AeroClave systems• Fogging in small areas• Fogging in irregularly-shaped areas
The AeroClave Advantage
• Most cost-effective product line
• Quickest average cycle times
• Simple automated operation
• Comprehensive suite of facility and asset management tools
• Environmentally-friendly process (“green”)
• Cost-effective operation per treatment cycle
• No residues - nothing to wipe down or wipe off
• Compatible with sensitive electronics
• Broadest range of materials compatibility
• Broadest range of product solutions for every industry