outdoor design guide - wsproducts.gr€¦ · outdoor design guide. ... icbog36 914 mm icbog42 1067...

ICB REVISED 3 / 2017

OUTDOOR DES IGN GU IDE

Features and specifications are subject to change at any time without notice.

Throughout this guide, dimensions may vary by ± 3 mm.

TA B L E O F C O N T E N T S

3 S U B - Z E R O O U T D O O R R E F R I G E R AT O R

7 W O L F O U T D O O R G R I L L S | M O D U L E S

14 W O L F O U T D O O R W A R M I N G D R A W E R

20 W A R R A N T I E S

Sub-Zero Outdoor Refrigerator Drawers

The Sub-Zero refrigerator drawers is a helpful addition to any outdoor kitchen. Compact, yet roomy, this integrated unit can be installed to fit flush with surrounding cabinetry. The outdoor model requires the use of Sub-Zero stainless steel outdoor accessory panels with pro handles to match Wolf outdoor products. These panels are available with or without a lock through an authorized Sub-Zero dealer. For local dealer information, visit our website, subzero.com.

OUTDOOR REFRIGERATOR

REFRIGERATOR DRAWERS

ICBID-24RO

subzero-wolf.com | 3

4 | subzero-wolf.com


OPENING DIMENSIONS

654 mmOPENING

DEPTH

610 mmOPENING WIDTH

876 mmOPENINGHEIGHT

*114 mm finished returns will be visible and should be finished to match cabinetry.

SIDE VIEW

TOP VIEW

FRONT VIEW

114 mm*FINISHEDRETURN

FRAMELESS CABINETRY

114 mm*FINISHEDRETURN

FILLER

FRAMED CABINETRY

610 mm 610 mm

Refrigerator Drawers

OVERALL DIMENSIONS

610 mm

467mm

610 mm

6 mm

876 mm* 268

mm

338mm

10 mm

92 mm*864 mm MIN TO 889 mm MAX

INTERIOR CAPACITY

REFRIGERATOR DRAWERS

Model ICBID-24RO 71 L

IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. The depth of the integrated model is 610 mm. Allow for

panel thickness when planning the finished opening depth. A minimum 114 mm finished return is required on all sides of the opening. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration.



Electrical

Installation must comply with all applicable electrical codes.

The electrical supply must be located within the shaded area shown in the illustration below. A separate circuit, ser-vicing only this appliance is required.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock.

The electrical outlet must be positioned with the grounding prong to the right of the thinner blades.

ELECTRICAL REQUIREMENTS

Electrical Supply 220–240 VAC, 50/60 Hz

Service 1 A

Receptacle 3-prong grounding-type

241mm

6 mm

108mm

114mm

FLOOR

LEFT SIDEOF OPENING

Electrical supply location.

Refrigerator Drawers

DUAL INSTALLATION

When installing two units side by side in a dual installa-tion, the opening width is the width of the two units added together. A dual installation kit will be required for this instal-lation. If a dual installation kit is not specified, a minimum 51 mm filler strip is required between units.

Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit our website, subzero.com.


Stainless Steel Panels

The outdoor model requires the use of Sub-Zero stainless steel outdoor accessory panels. These panels have pro handles to match Wolf outdoor products and are avail-able with or without a lock through an authorized Sub-Zero dealer. For local dealer information, visit our website, subzero.com.

The thickness of outdoor stainless steel panels is 38 mm. The depth of each integrated model is 610 mm. Allow for panel thickness when planning the finished opening depth.

Reveals of 3 mm are typical, however, the reveal between the upper and lower outdoor stainless steel panels is 6 mm to accommodate the lock.


Standard Handles

Optional stainless steel pro handles are avail able through an authorized Sub-Zero dealer. Refer to the chart below for standard handle length for the refrigerator drawers.

HANDLE LENGTH

Pro Handle 495 mm


Wolf Outdoor Grills | Modules

Taste what happens when the heritage of professional cooking moves from the kitchen to the patio. Like their indoor counterparts, Wolf outdoor grills are precision instruments. Constructed of heavy-duty stainless steel, the 76 cm, 91 cm, 107 cm and 137 cm grills have powerful burners every five inches for even heat distribution. An electric rotisserie with infrared burner produces succulent poultry and roasts. All grill models can be built-in and all except the 137 cm grill, can be used on a cart for portable convenience. The 7.3 kW burner module can be built into an outdoor kitchen and the side burner attached to a cart. Wolf grills and modules can be ordered in natural or LP gas.

OUTDOOR GRILLS | MODULES

OUTDOOR GRILLS

ICBOG30

ICBOG42

ICBOG36

ICBOG54

ICBBM13 BURNER MODULE

ICBSB13 SIDE BURNER

OUTDOOR MODULES


273 mm

762 mm

705 mm330mm

WWIDTH

MAX DOOR/DRAWER CLEARANCE 559 mm

610 mmTO GRILL

PLATFORM

927mm

705 mm

305mm

76 mm

762 mmHOOD CLOSED

318 mmTO GRILLING

SURFACE

686mm

WWIDTH

705 mm

64mm

CLEARANCEFOR OPEN

HOOD


Outdoor Grills | Modules

OUTDOOR GRILL

GRILL CART

BURNER MODULE | SIDE BURNER WIDTH—OUTDOOR GRILL W

ICBOG30 762 mm

ICBOG36 914 mm

ICBOG42 1067 mm

ICBOG54 1372 mm

WIDTH—GRILL CART W

ICBCART30 762 mm

ICBCART36 914 mm

ICBCART42 1067 mm



Outdoor Grills | Modules

BURNER RATING

GRILL BURNERS

ICBOG30, ICBOG36, ICBOG42, ICBBM13, ICBSB13 7.3 kWICBOG54 7.5 kW

SEAR ZONE

ICBOG36, ICBOG42 7.3 kWICBOG54 7.5 kW

ROTISSERIE

ICBOG30 4.1 kWICBOG36, ICBOG42 4.7 kWICBOG54 (2) 4.1 kW

Planning Information

For portable applications, Wolf grill carts are designed specifically to fit grill models ICBOG30, ICBOG36 and ICBOG42 and the side burner. Model ICBOG54 is designed for built-in applications only.

For built-in applications, Wolf outdoor grills and the burner module are designed for easy placement into a built-in enclosure. For outdoor grills, installation in a combustible enclosure requires an insulating liner. For the burner module, an insulating liner is not required. The enclosure should be built according to specifications for your specific installa-tion on the following pages. If the burner module is installed next to an outdoor grill, a minimum of 305 mm is required between units on the rotisserie motor side and 51 mm on the opposite side. A rotisserie side conversion kit is avail-able from an authorized Wolf dealer.

Optional stainless steel accessory doors and drawers are available for built-in applications.

Grill carts, insulating liners and stainless steel doors and drawers are avail able through an authorized Wolf dealer. For local dealer information, visit our website, wolfappliance.com.



GAS SUPPLY

Installation must comply with all applicable gas codes.

A gas supply line of 19 mm rigid pipe must be provided to the outdoor grill or module. If local codes permit, a certified, .9 m long, 13 mm or 19 mm ID flexible metal appliance con-nector is recommended to connect the units ISO 7-1 female inlet to the gas supply line.

An inline regulator is installed on the unit for connecting to NAT or LP gas sources. For local dealer information, visit our website, wolfappliance.com.

GAS REQUIREMENTS

NATURAL GAS

Supply Pressure 12.5 mbarMin Line Pressure 17.5 mbarMax Regulator Pressure 100 mbar

LP GAS

Supply Pressure 25 mbarMin Line Pressure 27.4 mbarMax Regulator Pressure 100 mbar


ELECTRICAL


The electrical outlet must be located within reach of the power cord. A separate circuit, servicing only this appli-ance is required. A ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock.

ELECTRICAL REQUIREMENTS (GRILL | MODULE)

Electrical Supply grounded, 220-240 VAC, 50/60 Hz

Service 1 A

Receptacle 3-prong grounding-type, IEC inlet

ELECTRICAL REQUIREMENTS (ROTISSERIE)

Electrical Supply—Input grounded, 220-240 VAC, 50/60 Hz

Electrical Supply—Output 12 VDC

Service 0.5 A (6 Watts)

Receptacle barrel plug, 2.1 mm ID x 5.5 mm OD


508mm

19 mm

479mm

762 mm

727 mm

527mm

287mm

657mm

19 mm

241mm

762 mm

686 mm

527mm

483mm

A

B

19 mm

32 mm


Accessory Doors | Drawers

DOORS

DOOR WIDTH A B

46 cm Single 457 mm 413 mm

76 cm Double 762 mm 718 mm




SINGLE DRAWER

DRAWER | DOOR UNIT

2- OR 3-DRAWER UNIT

527mm

508mm

19 mm

483mm

330 mm

305 mm


298mm

OPENINGHEIGHT

DOORS / DRAWERSOPENING WIDTH

616 mmOPENING

DEPTH

OPENINGHEIGHT

152mm

25 mm min

GRILLOPENING

21mm

COUNTERTOP OVERHANG

GRILLOVERLAP

FRONT VIEW

TOP VIEW

WOPENING WIDTH

NOTE: Shaded area above countertop indicates minimum clearance tocombustible surfaces, combustible materials cannot be located within this area.

64 mm

330mm

89mm

G

102 mm

152mm

G

321mm

OPENINGHEIGHT

DOORS / DRAWERSOPENING WIDTH

660 mmOPENING

DEPTH

OPENINGHEIGHT

305mm

25 mm min

273mm

127mm

CL

CL

70 mmKNOCKOUT

LINEROPENING

21mm

COUNTERTOP OVERHANG

LINEROVERLAP

FRONT VIEW

TOP VIEW

WOPENING WIDTH

NOTE: Shaded area above countertop indicates minimum clearance tocombustible surfaces, combustible materials cannot be located within this area.

305 mm

G


OPENING WIDTH—NON-COMBUSTIBLE W

ICBOG30 724 mm

ICBOG36 876 mm

ICBOG42 1029 mm

ICBOG54 1334 mm

Outdoor Grills

NON-COMBUSTIBLE INSTALLATION COMBUSTIBLE INSTALLATION

OPENING WIDTH—COMBUSTIBLE W

ICBOG30 851 mm

ICBOG36 1003 mm

ICBOG42 1156 mm

ICBOG54 1461 mm



254 mmOPENINGHEIGHT

616 mmOPENING

DEPTH

152mm

MODULEOPENING

14mm

COUNTERTOP OVERHANG

MODULEOVERLAP

FRONT VIEW

TOP VIEW

305 mmOPENING

NOTE: Shaded area above countertop indicates minimum clearance tocombustible surfaces, combustible materials cannot be located within this area.An insulating liner is not required.

G

203mm

178mm

G

76 mm

305 mm

Burner Module

INSTALLATION

Outdoor Grills

ACCESSORY DOORS | DRAWERS

OPENING—DOORS W H

46 cm Single 413 mm 483 mm





OPENING—DRAWERS W H

Single Drawer 692 mm 248 mm

2- or 3-Drawer Unit 308 mm 483 mm

Drawer | Door Unit 743 mm 483 mm

Wolf Outdoor Warming Drawer

Wolf warming drawers are designed to take care of prepared foods until it’s time to serve them. You can adjust the tem-perature, keeping moist foods moist and crisp foods crisp. Warming drawers are ideal for proofing dough. They can also be used to warm robes and towels. The stainless steel drawer front features a pro handle. The integrated drawer front allows for a custom wood panel and handle. Model ICBWWD30O, approved for outdoor installations, is ideal for any outdoor kitchen.

OUTDOOR WARMING DRAWER


PROFESSIONAL

CUSTOM PANEL

WARMING DRAWER FRONTS

STAINLESS STEEL

INTEGRATED


A

BWWIDTH

OPEN DRAWER

578 mm

718 mm

229mm

264mm

546mm

DIMENSIONS


Warming Drawer

DRAWER FRONT OPTIONS

Wolf warming drawer fronts allow for many design options, but the warming drawer itself will be the same for all appli-cations. A panel mounting kit is required when installing a custom panel. The panel mounting kit is available through an authorized Wolf dealer. For local dealer information, visit the find a showroom section of our website, wolfappliance.com.

The 51 mm thick drawer front, in 76 cm and 91 cm widths, is designed to be installed below an outdoor grill, so the panel aligns properly with the front of the grill. Dimensions for the warming drawer remain the same, even though the drawer front may be wider to match a Wolf 91 cm outdoor grill.

STAINLESS STEEL DRAWER FRONT

WIDTH W

76 cm Drawer Front 759 mm91 cm Drawer Front 911 mm

DEPTH A B

Professional 29 mm 89 mmProfessional (51 mm thick) 54 mm 114 mm

INTEGRATED DRAWER FRONT

CUSTOM PANEL W H D

Dimensions (typical) 759 mm 264 mm 19 mmMin Thickness 16 mm




The warming drawer must be installed with a Wolf drawer front, avail able through an authorized Wolf dealer. For local dealer information, visit our website, wolfappliance.com. Specific installation instructions are included with the drawer front.

The warming drawer can be installed in a standard or flush inset application.

For a standard installation, the drawer collar and front panel sit proud of the cabinet face frame. A recessed installation requires the cabinetry be recessed by 5 mm so the collar is flush with the cabinet face frame but the drawer front will sit proud. A flush inset installation requires the drawer collar and front panel be recessed to be flush with surrounding cabinetry. Refer to illustrations on the following pages for minimum cabinet dimensions for your specific installation.

Finish the edges of the opening. They may be visible when the drawer is open.

For standard installations, face trim will overlap stiles and rails. Refer to the chart below.

For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent reveals, each corner of the opening must be exactly 90°.

Model ICBWWD30O is approved for outdoor installations.

INSTALLATION REQUIREMENTS

Min Base Support 90 kg

Trim Overlap (top, bottom, sides) 16 mm

ELECTRICAL


Locate the electrical supply flush with the back wall and within the shaded area shown in the illustrations on the following pages. For ease of installation, the electrical supply for the warming drawer can be placed in an adjacent cabinet within reach of the power cord.

IMPORTANT NOTE: When installed outdoors, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock.

ELECTRICAL REQUIREMENTS

Electrical Supply 220–240 VAC; 50/60 Hz

Service 850 W

Receptacle 3-prong grounding-type

Power Cord .9 m



Warming Drawer

STANDARD INSTALLATION

FRONT VIEWSIDE VIEW

TOP VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth.

584 mmOPENING

DEPTH

E

727 mmOPENING WIDTH

232 mmOPENINGHEIGHT

ANTI-TIP BLOCK


FRONT VIEWSIDE VIEW

TOP VIEW

*Will be visible and should be finished to match cabinetry.**Dimension provides minimum reveals.

NOTE: Location of electrical supply within opening may require additional cabinet depth.

610 mmFLUSH INSET

DEPTH

ADRAWERFRONTDEPTH

270 mmFLUSHINSET

HEIGHT**

765 mmFLUSH INSET WIDTH**

19 mm

19 mm

19 mm E

E

FINISHEDCLEATS*

ANTI-TIP BLOCK

Warming Drawer

FLUSH INSET INSTALLATION


DRAWER FRONT DEPTH A

Professional 29 mm

Professional (51 mm thick) 54 mm

Custom front panel depth is dependent on panel thickness.


Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design, are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries. All other trademarks are property of their respective owners in the United States and other countries.

Sub-Zero International Outdoor Limited Warranty*

FOR RESIDENTIAL USE

FULL ONE YEAR WARRANTY**

For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.

FULL FIVE YEAR SEALED SYSTEM WARRANTY

For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.

TERMS APPLICABLE TO EACH WARRANTY

The warranty applies only to products installed for normal residential use. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair.

For more information regarding your Sub-Zero product warranty, contact your dealer. Warranties must comply to all country, state, city, local and or ordinance.

*Product must be approved for outdoor use, designated by model and serial number.

**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects.

**Replacement water filters are not covered by the product warranty.

Wolf Appliance International Outdoor Limited Warranty*

FOR RESIDENTIAL USE

FULL ONE YEAR WARRANTY**

For one year from the date of original installation, this Wolf Appliance product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Wolf Appliance under the above warranty must be performed by Wolf factory certified service, unless otherwise specified by Wolf Appliance, Inc. Service will be provided during normal business hours.

LIMITED FIVE YEAR WARRANTY

For five years from the date of original installation, Wolf Appliance will repair or replace the following parts that prove to be defective in materials or workmanship: stainless steel briquette trays, gas valves, drip pans, electronic control boards and electric heating elements. If the owner uses Wolf factory certified service, the service provider will repair or replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Wolf Appliance, Inc. (using the information below) to receive repaired or replacement parts. Wolf Appliance will not reimburse the owner for parts purchased from non-certified service or other sources.

For more information regarding your Wolf product warranty, contact your authorized Wolf dealer. Warran-ties must comply to all country, state, city, local and or ordinance.

*Product must be approved for outdoor use, designated by model and serial number.

**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects.

SUBZERO-WOLF.COM

outdoor design guide - wsproducts.gr€¦ · outdoor design guide. ... icbog36 914 mm icbog42 1067...

Documents