overspeed governors and accessories product...

Seite Zertifikat nach DIN EN ISO 9001

Overspeed governors

and accessories

Product information to

HJ 200 (AGB 001/2) and

HJ 200 Z12 (AGB 027/2)

Urheberrecht / Copyright

Copyright remaining with JUNGBLUT. © 2011 by JUNGBLUT, Germany

Hans Jungblut GmbH & Co. KG Ostheimer Straße 171 D-51107 Köln Fon: +49 (0)221 - 801938-0 Fax: +49 (0)221 - 801938-10 www.jungblut.de [email protected]

Overspeed governors and accessories HJ 200-Product information

Status: 8. October 2013 page 2

Content Page

Range of applications for overspeed governors 3

Overview of extent of delivery for overspeed governors and

accessories 4

Functional description of the overspeed governors 9

Prototype test and certification 10

Works speed setting 11

Safety switch 11

Remote triggering 12

Electrical preliminary switch off 12

Test groove 13

Creeping protection 13

Overspeed governor with emergency limit shut-down 14

Rotary encoder connection and rotary encoder 14

Special overspeed governors: 15

The overspeed governors HJ 200 SB O / U - Z6 15

The overspeed governors HJ 200 …-H 15

Appendix 1: Order number list 15

Appendix 2: Technical drawings 23



Range of applications for overspeed governors

type of driving rope: round strand rope made of steel wires driving rope diameter: (rope ø acc. to table) tripping overspeed governor: (tripping v1 acc. to table)

maximum rated speed: (rated v max acc. to table)

Overspeed-governor

Component testing

rope Ø [mm]

Tripping V1 [m/s]

Rated Vmax [m/s]

Retraction of the safety gear in both directions of rotation (6 safety cogs)

HJ 200 SB O AGB 001/2 6 - 6.5 0.50 - 2.02 1.60

HJ 200 SB U AGB 001/2 6 - 6.5 0.24 - 1.50 1.25

Retraction of the safety gear in one direction of rotation (12 safety cogs)

HJ 200 SB O - Z12 AGB 027/2 6 - 6.5 0.50 - 1.16 1.0 1

HJ 200 SB U - Z12 AGB 027/2 6 - 6.5 0.24 - 1.16 1.0 1 Retraction of the safety gear in one direction of rotation (6 safety cogs)

HJ 200 SB O - Z6 AGB 001/2 6 - 6.5 0.50 - 2.02 1.60

HJ 200 SB U - Z6 AGB 001/2 6 - 6.5 0.24 - 1.50 1.25

Important notes regarding the above overspeed gover nors:

� Code "R" = hardened V-groove is omitted. All V-grooves of the OSG wheels are hardened. � Code "W" = maintenance-free ball bearings is omitted. All OSG wheels are equipped with

maintenance-free ball bearings. The arresting pendulum is equipped with maintenance-free friction bushings and must not be lubricated.

� "Right/left version" = position of the pendulum roll The OSG arrests in both directions. If not

specified in the order, a right version OSG is supplied. Note: For retrofitted creeping protection, specify the type!

� "Right/left release direction" = defines the direction of arresting. The OSG arrests only in the

specified direction.

Ravi.fongsoon

Highlight



Overview of extent of delivery for overspeed govern ors and accessories

HJ 200 SB O

Overspeed governor (OSG) with governor wheel diameter 200 mm, 6 safety cogs (symmetrical) for retraction of the safety gear in both directions of rotation, narrow base plate design, overhead arresting pendulum Order-No. 02-202-01-000, right version Order-No. 02-203-01-000, left version

HJ 200 SB U

Overspeed governor (OSG) with governor wheel diameter 200 mm, 6 safety cogs (symmetrical) for retraction of the safety gear in both directions of rotation, narrow base plate design, underhead arresting pendulum Order-No. 02-202-02-000, right version Order-No. 02-203-02-000, left version

HJ 200 SB O - Z6

Overspeed governor (OSG) with governor wheel diameter 200 mm, 6 safety cogs (symmetrical) for retraction of the safety gear in one direction of rotation, narrow base plate design, overhead arresting pendulum Order-No. 02-200-03-000, right release direction Order-No. 02-201-03-000, left release direction

HJ 200 SB U - Z6

Overspeed governor (OSG) with governor wheel diameter 200 mm, 6 safety cogs (symmetrical) for retraction of the safety gear in one direction of rotation, narrow base plate design, underhead arresting pendulum Order-No. 02-200-04-000, right release direction Order-No. 02-201-04-000, left release direction

HJ 200 SB O - Z12

Overspeed governor (OSG) with governor wheel diameter 200 mm, 12 safety cogs (asymmetrical) for retraction of the safety gear in one direction of rotation, narrow base plate design, overhead arresting pendulum Order-No. 02-200-05-000, right release direction Order-No. 02-201-05-000, left release direction

HJ 200 SB U - Z12

Overspeed governor (OSG) with governor wheel diameter 200 mm, 12 safety cogs (asymmetrical) for retraction of the safety gear in one direction of rotation, narrow base plate design, underhead arresting pendulum Order-No. 02-200-06-000, right release direction Order-No. 02-201-06-000, left release direction

Ravi.fongsoon

Highlight



Optional features for OSGs (all above OSG types can be fitted accordingly by JUNGBLUT upon order)

Test groove 40% Test groove for test purposes for OSG HJ 200, transmission ratio: 1:1.40 For order number, see appendix 1 "Order number list "

Test groove special design Test groove for test purposes, for transmission ratios deviating from the above designs - ON REQUEST -

Suspended design Suspended design (cable pull downwards) can be assembled directly to the shaft head For order number, see appendix 1 "Order number list "

Rotary encoder and rotary encoder attachment

Incremental rotary encoder - ON REQUEST -

Toothed belt extension kit 1

For rotary encoder connection with toothed belt drive (radial), for shaft d=8x20/25mm, transmission ratio 4:1, consisting of gear ring 44 cogs, gear wheel 11 cogs, toothed belt, fixing plate For order number, see appendix 1 "Order number list "

Toothed belt extension kit 2 As above, for shaft d=10x20/25mm, gear ring 48 cogs, gear wheel 12 cogs For order number, see appendix 1 "Order number list "

Extension kit axial HJ 200 (shaft+bridge)

For mounting of the decoder on a bridge flange-mounted to the HJ 200; connection to axially protruding shaft, e.g. d=10mm x l=20mm Connecting coupling and installation to be provided/performed by customer! For order number, see appendix 1 "Order number list "

Extension kit axial HJ 200 (shaft)

As above, but for direct mounting of a hollow shaft rotary encoder on an axially protruding shaft, e.g. d=10mm x l=20mm; to be installed by customer! For order number, see appendix 1 "Order number list "



Optional features for OSGs (all above OSG types can be fitted accordingly by JUNGBLUT upon order or by the customer himself)

Kombi kit HJ 200

Mounting kit for emergency limit shut-down, consisting of mounting bracket with control current end switch (safety switch 12345), switching rods, triggering springs (length 600 mm) and attachment kit for direct attachment to HJ 200 base plate; SAS 200 Kombi rope-jump-off protection Order-No. 02-21-003

AS kit HJ 200 A3 12 VDC

Mounting kit for creeping protection, acc. to EN 81-1/2:1998+A3:2009, consisting of mounting bracket with pre-mounted 12 VDC, 1,41A, solenoid, 100% ED and monitoring switch (safety switch 12345) with roller kit and mounting kit for direct attachment to the bearing plate of the OSG Attention: Not suitable for Z-Type !!! Order-No. 02-21-020-12 right version Order-No. 02-21-023-12 left version

AS kit HJ 200 A3 24 VDC

As above, however with solenoid with 24 VDC, 0.66A, duty cycle 100% Attention: Not suitable for Z-Type !!! Order-No. 02-21-020-24 right version Order-No. 02-21-023-24 left version

AS kit HJ 200 A3 230 VAC

As above, however with solenoid with 230 VAC, 0.09A, duty cycle 100% Attention: Not suitable for Z-Type !!! Order-No. 02-21-020-230 right version Order-No. 02-21-023-230 left version

Adapter plate 200 - N Adapter plate (200x155x6mm) with fixing materials to assemble to the overspeed governor Order-No. 02-21-001

Adapter plate 200 – N -P Adapter plate (214x155x6mm) with fixing materials to assemble to the overspeed governor with test groove Order-No. 02-21-011

Key-operated pushbutton AS Key-operated pushbutton to activate the creeping protection or remote triggering, 1 opener contact, 1 closer contact Order-No. 02-34-082



Special safety switches at the overspeed governor

Safety switch 20K gripping 1 opener

Safety switch with slow-motion switching (gripping), IP 67, 1 opener (230 VAC – 4A = 24 VDC – 1A), INCLUDED AS STANDARD IN DELIVERY

Order-No. 02-20-502 (right); 02-20-501 (left)

Safety switch 34 gripping 2xO

Safety switch with slow-motion switching (gripping), IP 67, 2 openers (230 VAC – 4A = 24 VDC – 1A)


Safety switch 12345 gripping 1xO and 1xC

Safety switch with slow-motion switching (gripping), IP 67, 1 opener, 1 closer (230 VAC – 4A = 24 VDC – 1A)


Safety switch 20K MG latching 1xO

Safety switch with snap-action operation (latching), IP 67, 1 opener (230 VAC – 4A = 24 VDC – 1A)


Safety switch 45 latching 2xO

As above, however with 2 opener contacts


Safety switch 234 latching 1xO and 1xC

As above, however with 1 opener and 1 closer contact


Electrical preliminary switch off 1xO

Electrical safety device to EN 81-1, 9.9.11.1, for rated speed > 1.00 m/s, with one switch with end position latching for the downwards and upwards direction, electromagnetic reset of the set bolt 1 opener, latching, IP 67, 230 VAC- 4 A = 24 VDC - 4 A, reset solenoid: 230 VAC or 24 VDC, duty cycle 2.5% Order-No. 02-20-601, 230VAC; 02-20-605, 24VDC; left Order-No. 02-20-600, 230VAC; 02-20-604, 24VDC; righ t

Electrical preliminary switch off 2xO 1xC

As above, however switch with 2 opener and 1 closer contacts, latching, IP 67, 230 VAC - 4A = 24 VDC - 4A, reset solenoid: 230 VAC or 24 VDC , duty cycle: 3 % Order-No. 02-20-603, 230VAC; 02-20-607, 24VDC; left Order-No. 02-20-602, 230VAC; 02-20-606, 24VDC; righ t

Ex-switch Eex 95 W

Safety switch with slow-motion switching (gripping), explosion protection Ex II 2G EEx de IIC T6, 1 opener and 1 closer to DMT 01 ATEX E 118 (250 VAC – 6A) Order-No. 01-21-058 (no difference between left and right)



Remote triggering for functional control in case of no access (to EN 81-1, 9.9.8.3)

FGS 230 VAC rectifier-connector

Remote triggering (solenoid) with rectifier connector 230 VAC - 196 VDC / 0.88 A, duty cycle 5% Order-No. 02-21-004-230

FGS 230 VAC subsequent attachment

As above, with fixing materials for subsequent connection to OSG, observe installation instructions! Order-No. 02-21-004-230-1

FS 196 VDC

Remote triggering (solenoid) with counter connector for direct voltage 196 VDC / 0.88 A, duty cycle 5% Order-No. 02-21-004-196

FS 24 VDC

Remote triggering (solenoid) with counter connector for direct voltage, 24 VDC / 7.23 A, duty cycle 5% Order-No. 02-21-004-24

FS 12 VDC

Remote triggering (solenoid) with counter connector for direct voltage, 12 VDC / 13.79 A, duty cycle 5% Order-No. 02-21-004-12

FS 12 VDC subsequent attachment

As above, with fixing materials for subsequent connection to OSG, observe installation instructions! Order-No. 02-21-004-12-1


As above, with 24 voltages DC Order-No. 02-21-004-24-1


As above, with 196 voltages DC Order-No. 02-21-004-196-1

Key-operated pushbutton FG Key-operated pushbutton to activate the remote triggering, 1 closer contact Order-No. 01-34-082

Switch as pulse generator

Magnetic switch

Magnetic switch with switch output as changeover switch, max. 60 W/VA, max. 250 VAC / DC, max. 1A, IP 67, with 1 magnet mounted on the governor-wheel Order-No. 01-20-061

Additional magnet Additional magnets mounted on the governor-wheel Order-No. 01-20-064

Inductive sensor Inductive sensor, (15-34 VDC, 200 mA, 1 closer, IP 67) Order-No. 01-22-062



Inductive Teach-In sensor (Rotational control)

Inductive sensor programmable using voltage pulse (10-36 VDC, <200 mA, closer, IP 67, 1 closer) Order-No. 01-20-110

Rope jump-off protection to EN 81-1, 9.7.1

Rope jump-off protection 200 For OSG HJ 200 Order-No. 02-23-006

Rope jump-off protection 200 Kombi

For OSG HJ 200 Kombi design Order-No. 02-23-010

Rope jump-off protection 200 Test groove

For OSG HJ 200 with test groove Order-No. 02-23-011

Rope jump-off protection 200 Kombi test groove

For OSG HJ 200 with Kombi design and test groove Order-No. 02-23-030

Miscellaneous for overspeed governors

Special painting for governor Special painting of the end shields/ base plate of the OSG, deviating from the standard colour RAL 7016) Order-No. 01-21-090

2nd rating plate Additional rating plate on the rear of the OSG Order-No. 01-24-091

Protective hood HJ 200 As access protection for OSG HJ 200, made of perforated plate, Order-No. 01-32-068

Refrigerator design HJ 200 For use in cold storage house -30°C, special label at the overspeed governor Order-No. 02-20-090

Functional description of the overspeed governors The overspeed governor is the mechanical, positive acting release organ for a safety gear on the lift or similar conveyor and lifting gear. It primarily consists of a base plate, two lateral end shields, the Kombi governor wheel with rope uptake, blocking collar and curve control, as well as the retaining pawl (arresting pendulum). A self-aligning roller with rubber ring located on the arresting pendulum bearing is drawn on the turning wheel with an extension spring arranged between the pendulum and end shield. When the



governor wheel turns the self-aligning roller bearing rolls over the turning wheel. Due to the curve cam impulse force acting against the extension spring force the pendulum carries out a swinging movement. The retaining pawl part (gripping catch) opposite the self-aligning roller bearing relative to the pendulum bearings acts from a certain speed (on reaching the preset tripping speed v1) of the Kombi wheel, at the given extension spring force, in the blocking collar and suddenly blocks the wheel. This causes a force dependent on various factors to be formed between the groove and the drawn, driven governor rope, due to friction, with which the safety gear is mechanically strained and pushed inwards. This takes place with Jungblut governors in both directions of rotation, i.e. in the upwards and downwards movement of the lift car, with the exception of the Z12 and Z6 types, which only act mechanical strained in the downwards direction at the tripping speed. With the previously described swivel movement of the pendulum, an additional safety switch is actuated via a lever attached to this pendulum for positive opening of the control current circuit. This takes place in overspeed governors up to a normal speed of 1.00 m/s at the same time as the mechanical interception. In lifts with a rated speed greater than 1.00 m/s, this must take place before the tripping speed is reached (EN 81-1, 9.9.11.1) and can take place by means of preliminary switch off.

Prototype test and certification Jungblut overspeed governors with AGB component testing are prototype tested safety components for rope and hydraulic lifts to EN 81-1 and EN 81-2, as well as for similar conveyor and lifting gear, such as e.g. shelf-operating equipment. Each overspeed governor of the EC-type-examination certificate as well as the EC declaration of conformity in accordance with EG Lift Directive 95/16/EG. The CE mark is integrated in the rating plate of the overspeed governor. The EC-type-examination certificate, as well as the operating and maintenance instructions provide additional information about the installation and use of the governor. Important information is summarised in the overviews of the range of use as well as the selection parameters for Jungblut overspeed governors. With respect to EN 81, lease note that “measures“ are also required, to prevent the ropes from jumping from their pulleys when they become slack, as well as the penetration of foreign bodies between the rope and pulley. This requirement can be fulfilled in the Jungblut governors by the offer of the following order items: rope jump-off protection, slack rope switch for tensioning weight, protective cover for the rope pulley.



Works speed setting According to the valid regulations (e.g. EN 81), a permissible tripping speed v1 (m/s) is selected for the given rated speed v (m/s), which enables fault-free operation and does not exceed the highest possible limit of these regulations. This specification is carried out by the customers or by Jungblut if the relevant information is provided. The tripping speed set in the works is sealed and must not be deliberately or unconsciously manipulated.

Safety switch Apart from the mechanical arrestor of the overspeed governor, a safety switch is positively actuated, which interrupts the control current circuit (opener contact). Jungblut overspeed governors operate at the tripping speed in a downwards and upwards direction and thus positively actuate the attached safety switch in bother directions of rotation, with the exception of the already aforementioned Z12 and Z6-types, which only automatically mechanically open the switching contact in a downwards direction at the tripping speed. Both “gripping“, as well as “latching“ design switches are available for the Jungblut overspeed governor. In the gripping safety switch design the switching contact automatically closes, if the pendulum returns to its initial position by turning the governor wheel against the direction of rotation of the operation. In the latching safety switch design on the other hand, the switch contact also has to be reconnected by pulling the contact tappet on the switch. The standard version of the Jungblut overspeed governor is equipped with the safety switch 20K Different to the “gripping“ design, this switch can also be used in the 20K MG model as a “latching“ switch with restart lockout. In addition safety switches in “gripping” or “latching“ design with switching contact: an opener and a closer, or two openers are available for higher standards with respect to contact assignment. For explosion-protected ranges a “gripping” safety switch (an opener and a closer) with explosion protection is available.



Remote triggering The remote triggering (solenoid) serves to functionally control the overspeed governor, if this is not accessible, e.g. in case of shaft installation. In the case of remote triggering, the magnetic coil of the solenoid is energised on actuation of a pulse driven key-operated pushbutton, whereby this pulls down the arrester catch of the arrester pendulum with the aid of an anchor rod. The arresting pendulum then drops into the blocking collar of the overspeed governor wheel and initiates the arrestor process when the wheel is turned. Standard design Jungblut remote solutions are supplied for direct connection via a rectifier connector. Please note that when on pressing the key-operated pushbutton for the remote triggering, that this must be pressed not longer than 5 seconds per minute. This can be identified by a noticeable warning sign on the push button. The remote triggering with rectifier connector connection, can be supplied for the subsequent attachment of remote triggering. In particular, please note the assembly and safety instructions attached to the operating and maintenance instructions. For supply voltage 196 VDC or 24 VDC or 12 VDC three additional remote triggerings are available.

Electrical preliminary switch off The electrical preliminary switch off is an “electrical safety device“ in accordance with EN 81-1, 9.9.11.1, which causes the control current circuit to be opened and that an electric safety device stops the car (minimum 115% of the rated speed). With Jungblut governors, this takes place in both directions of rotation, i.e. during both the upwards and downwards run of the lift car and must be included in the order from a rated speed greater than 1,00 m/s, in accordance with EN 81. Please also note the minimum tripping speed v1min=0,60 m/s for the HJ 200 with preliminary switch off which is due to the design. The preliminary switch off switch is actuated as for the safety switches by tilting the lowering pin on the arresting pendulum, whereby the switch can be adjusted according to the prescribed



preliminary switch offspeed. The switching contacts open automatically at the “arrestor“ at the latest. The Jungblut overspeed governor HJ 200 can be supplied with one switch for both directions of rotation and electromagnetic reset of the contact pin. Please not that in the case of the Z-12 models, a preliminary switch off is generally supplied with separate switches for the upwards / downwards movement. This design of the preliminary switch off with electromagnetic reset of the contact pin is particularly recommended for shaft installation (see also remote triggering), whereby the set bolts that have locked into place can be reset with a pushbutton. Please note the duty cycle 3% or 4,5% (see content of delivery) of the reset solenoid!

Test groove In the test groove, the tripping speed is produced when travelling at rated speed if the rope is moved from the main groove to the test groove, due to the fact that the ratio of the diameters of the main groove to the test groove equates to the ratio of the tripping speed v1 to the rated speed v. If the pendulum locks into place, the tripping speed is maintained; if the pendulum does not lock into place, the set speed is exceeded. The test groove is designed as a 38° groove, as is the main groove, however without undercut. The standard version of the test groove is designed for a transmission ratio of 1:1.40 for the overspeed governor HJ 200. Deviating transmission ratios, which require a special test groove design, are only available on request.

Creeping protection

The creeping protection is a separate special mechanism attached to the OSG that prevents inadvertent dropping or lifting of the list cage. A magnetic coil is attached to the side of the OSG by means of a mounting bracket. The front tip of the magnet armature points towards the pendulum roller arm of the arresting pendulum. While the lift cage is travelling, the magnet armature is retracted by a 100 % ED DC magnet so that the OSG wheel can rotate freely in both directions. A safety switch actuated by the magnet armature is closed an monitors the armature position of the magnet. As soon as the lift cage stops at a floor, the magnet is de-energised and the retracted magnet armature is pushed by spring force in the direction of the pendulum roller arm. The front tip of the armature is now located on or below the pendulum roller arm of the arresting pendulum. If the lift



cage is inadvertently lowered or lifted (= OSG wheel turning), the magnet armature is moved to a position below the pendulum roller arm of the arresting pendulum, stopping the mechanism in arresting position, so that the arresting pendulum engages in the safety cogs. The design of the devices prevents incorrect connection, provided that the operating, installation and maintenance instructions are adhered to!

Overspeed governor with emergency limit shut-down

With this combined system, the emergency limit switch is triggered when a preset upper or lower limit point in the lift shaft is exceeded. At these limit points, the adjustable coil springs (combined springs) attached to the governor cable by means of cable clamps swivel the switching forks of the overspeed governor outwards, triggering the mechanism. The design of the devices prevents incorrect connection, provided that the operating, installation and maintenance instructions are adhered to!

Rotary encoder connection and rotary encoder Jungblut overspeed governors can be built with a special design for shaft copying for the attachment of a rotary encoder, for encoders with shaft stub or encoders with hollow shafts. These models are provided for direct connection via a retracted shaft stub axially mounted on the overspeed governor. The encoder is mounted on a flange-mounted bridge fitted to the governor (precisely flush) with the shaft. The customer provides the connection link and assembly of the encoder, insofar as the encoder is not purchased from Jungblut. Alternatively it is possible to assemble a hollow shaft encoder directly to the shaft stub of the overspeed governor Apart from the possibility of the aforementioned axial sensor fixings, it is also possible to radially connect a rotary encoder with shaft stub to the overspeed governor via a toothed belt. The transmission ratio of the ring gear of the governor-wheel, to the gear wheel for holding the toothed belt on the shaft of the sensor is 4:1. The toothed belt extension kit consists of a gear ring with 44 or 48 teeth, a gear wheel with 11 or 12 teeth, the toothed belt, as well as the fixing plate. Apart from the preparation for the connection of a rotary encoder, an incremental rotary encoder can also be purchased directly from Jungblut (after technical clarification). The encoders are attached to the overspeed governor with one of the aforementioned possibilities.



Special overspeed governors:

The overspeed governors HJ 200 SB O / U - Z6

This special model of the HJ 200 SB O – Z6 or HJ 200 SB U - Z6 features a special arresting pendulum so that the OSG wheel is blocked only on one side. The model can thus be used in installations with only one arresting direction for the OSG.

The overspeed governors HJ 200 …-H

The HJ 200 SB O – H, HJ 200 SB O - Z12 – H and HJ 200 SB O - Z6 – H overspeed governors are "suspended" mechanisms turned by 180° (for exam ple at the top end of the shaft).



Appendix 1: Order number list

The 3-digit order code (e.g. 001) follows the basic model codes

• 1. HJ 200 SB O • 2. HJ 200 SB U • 3. HJ 200 SB O – Z6 • 4. HJ 200 SB U – Z6 • 5. HJ 200 SB O – Z12 • 6. HJ 200 SB U – Z12

to form the last 3 digits of the order number and indicates the following options: Code No. Description P 001 Test groove 40% H 007 Suspended design ZAV - 44 005 Toothed belt extension kit 1, 44 cogs, front side ZAH - 44 006 Toothed belt extension kit 1, 44 cogs, rear side ZAV - 48 008 Toothed belt extension kit 2, 48 cogs, front side ZAH - 48 009 Toothed belt extension kit 2, 48 cogs, rear side WSHB 004 Extension kit axial shaft + bridge, rear side WSV 002 Extension kit axial shaft, front side WSH 003 Extension kit axial shaft, rear side

Examples:

• The HJ 200 SB O overspeed governor, right-hand model, with order number. 02-202-01-000 can be upgraded to HJ 200 SB O – P, order number 02-202-01-001 with check groove.

• The HJ 200 SB O overspeed governor with check groove and cogged V-belt kit 1, 44 cogs, front-mounted becomes HJ 200 SB O - P - ZAV - 44 , order number 02-202-01-015

Note: The order numbers below represent all available combinations of the above functions. For OSGs working on 2 directions, only the right model is listed; for OSGs working in one direction only, the model for right-hand direction of rotation is listed!



1. Overspeed governor HJ 200 SB O , Order-No. 02-202-01-000

Code: Order-No.: HJ 200 SB O - ZAV - 44 02-202-01-005 HJ 200 SB O - ZAH - 44 02-202-01-006 HJ 200 SB O - ZAV - 48 02-202-01-008 HJ 200 SB O - ZAH - 48 02-202-01-009 HJ 200 SB O - WSHB 02-202-01-004 HJ 200 SB O - WSV 02-202-01-002 HJ 200 SB O - WSH 02-202-01-003

identical nomenclature for HJ 200 SB O, left, Order-No. 02-203-01-000 1.1 Overspeed governor HJ 200 SB O - P Order-No. 02-202-01-001

Code: Order-No.: HJ 200 SB O - P - ZAV - 44 02-202-01-015 HJ 200 SB O - P - ZAH - 44 02-202-01-016 HJ 200 SB O - P - ZAV - 48 02-202-01-018 HJ 200 SB O - P - ZAH - 48 02-202-01-019 HJ 200 SB O - P - WSHB 02-202-01-014 HJ 200 SB O - P - WSV 02-202-01-012 HJ 200 SB O - P - WSH 02-202-01-013

identical nomenclature for HJ 200 SB O - P, left, Order-No. 02-203-01-001 1.2. Overspeed governor HJ 200 SB O - H Order-No. 02-202-01-007

Code: Order-No.: HJ 200 SB O - H - ZAV - 44 02-202-01-075 HJ 200 SB O - H - ZAH - 44 02-202-01-076 HJ 200 SB O - H - ZAV - 48 02-202-01-078 HJ 200 SB O - H - ZAH - 48 02-202-01-079 HJ 200 SB O - H - WSHB 02-202-01-074 HJ 200 SB O - H - WSV 02-202-01-072 HJ 200 SB O - H - WSH 02-202-01-073

identical nomenclature for HJ 200 SB O - H, left, Order-No. 02-203-01-007 1.3. Overspeed governor HJ 200 SB O - P - H Order-No. 02-202-01-017

Code: Order-No.: HJ 200 SB O - P - H - ZAV - 44 02-202-01-175 HJ 200 SB O - P - H - ZAH - 44 02-202-01-176 HJ 200 SB O - P - H - ZAV - 48 02-202-01-178 HJ 200 SB O - P - H - ZAH - 48 02-202-01-179 HJ 200 SB O - P - H - WSHB 02-202-01-174 HJ 200 SB O - P - H - WSV 02-202-01-172 HJ 200 SB O - P - H - WSH 02-202-01-173

identical nomenclature for HJ 200 SB O - P - H, left, Order-No. 02-203-01-017



2. Overspeed governor HJ 200 SB U , Order-No. 02-202-02-000

Code: Order-No.: HJ 200 SB U - ZAV – 44 02-202-02-005 HJ 200 SB U - ZAH - 44 02-202-02-006 HJ 200 SB U - ZAV – 48 02-202-02-008 HJ 200 SB U - ZAH – 48 02-202-02-009 HJ 200 SB U – WSHB 02-202-02-004 HJ 200 SB U – WSV 02-202-02-002 HJ 200 SB U – WSH 02-202-02-003

identical nomenclature for HJ 200 SB U, left, Order-No. 02-203-02-000 2.1 Overspeed governor HJ 200 SB U - P Order-No. 02-202-02-001

Code: Order-No.: HJ 200 SB U - P - ZAV - 44 02-202-02-015 HJ 200 SB U - P - ZAH - 44 02-202-02-016 HJ 200 SB U - P - ZAV - 48 02-202-02-018 HJ 200 SB U - P - ZAH - 48 02-202-02-019 HJ 200 SB U - P - WSHB 02-202-02-014 HJ 200 SB U - P - WSV 02-202-02-012 HJ 200 SB U - P - WSH 02-202-02-013

identical nomenclature for HJ 200 SB U - P, left, Order-No. 02-203-02-001



3. Overspeed governor HJ 200 SB O - Z6 , Order-No. 02-200-03-000

Code: Order-No.: HJ 200 SB O - Z6 - ZAV – 44 02-200-03-005 HJ 200 SB O - Z6 - ZAH - 44 02-200-03-006 HJ 200 SB O - Z6 - ZAV – 48 02-200-03-008 HJ 200 SB O - Z6 - ZAH – 48 02-200-03-009 HJ 200 SB O - Z6 – WSHB 02-200-03-004 HJ 200 SB O - Z6 – WSV 02-200-03-002 HJ 200 SB O - Z6 – WSH 02-200-03-003

identical nomenclature for HJ 200 SB O - Z6, left, Order-No. 02-201-03-000 3.1 Overspeed governor HJ 200 SB O - Z6 - P Order-No. 02-200-03-001

Code: Order-No.: HJ 200 SB O - Z6 - P - ZAV – 44 02-200-03-015 HJ 200 SB O - Z6 - P - ZAH - 44 02-200-03-016 HJ 200 SB O - Z6 - P - ZAV – 48 02-200-03-018 HJ 200 SB O - Z6 - P - ZAH - 48 02-200-03-019 HJ 200 SB O - Z6 - P - WSHB 02-200-03-014 HJ 200 SB O - Z6 - P - WSV 02-200-03-012 HJ 200 SB O - Z6 - P - WSH 02-200-03-013

identical nomenclature for HJ 200 SB O - Z6 - P, left, Order-No. 02-201-03-001 3.2. Overspeed governor HJ 200 SB O - Z6 - H Order-No. 02-200-03-007

Code: Order-No.: HJ 200 SB O - Z6 - H - ZAV - 44 02-200-03-075 HJ 200 SB O - Z6 - H - ZAH - 44 02-200-03-076 HJ 200 SB O - Z6 - H - ZAV - 48 02-200-03-078 HJ 200 SB O - Z6 - H - ZAH - 48 02-200-03-079 HJ 200 SB O - Z6 - H - WSHB 02-200-03-074 HJ 200 SB O - Z6 - H - WSV 02-200-03-072 HJ 200 SB O - Z6 - H - WSH 02-200-03-073

identical nomenclature for HJ 200 SB O - Z6 - H, left, Order-No. 02-201-03-007 3.3. Overspeed governor HJ 200 SB O - Z6 - P - H Order-No. 02-200-03-017

Code: Order-No.: HJ 200 SB O - Z6 - P – H - ZAV - 44 02-200-03-175 HJ 200 SB O - Z6 - P – H - ZAH - 44 02-200-03-176 HJ 200 SB O - Z6 - P – H - ZAV - 48 02-200-03-178 HJ 200 SB O - Z6 - P – H - ZAH - 48 02-200-03-179 HJ 200 SB O - Z6 - P – H - WSHB 02-200-03-174 HJ 200 SB O - Z6 - P – H - WSV 02-200-03-172 HJ 200 SB O - Z6 - P – H - WSH 02-200-03-173

identical nomenclature for HJ 200 SB O - Z6 - P - H, left, Order-No. 02-201-03-017



4. Overspeed governor HJ 200 SB U - Z6 , Order-No. 02-200-04-000

Code: Order-No.: HJ 200 SB U - Z6 - ZAV - 44 02-200-04-005 HJ 200 SB U - Z6 - ZAH - 44 02-200-04-006 HJ 200 SB U - Z6 - ZAV - 48 02-200-04-008 HJ 200 SB U - Z6 - ZAH - 48 02-200-04-009 HJ 200 SB U - Z6 - WSHB 02-200-04-004 HJ 200 SB U - Z6 - WSV 02-200-04-002 HJ 200 SB U - Z6 - WSH 02-200-04-003

identical nomenclature for HJ 200 SB U - Z6, left, Order-No. 02-201-04-000 4.1 Overspeed governor HJ 200 SB U - Z6 - P Order-No. 02-200-04-001

Code: Order-No.: HJ 200 SB U - Z6 - P - ZAV - 44 02-200-04-015 HJ 200 SB U - Z6 - P - ZAH - 44 02-200-04-016 HJ 200 SB U - Z6 - P - ZAV - 48 02-200-04-018 HJ 200 SB U - Z6 - P - ZAH - 48 02-200-04-019 HJ 200 SB U - Z6 - P - WSHB 02-200-04-014 HJ 200 SB U - Z6 - P - WSV 02-200-04-012 HJ 200 SB U - Z6 - P - WSH 02-200-04-013

identical nomenclature for HJ 200 SB U - Z6 - P, left, Order-No. 02-201-04-001



5. Overspeed governor HJ 200 SB O - Z12 , Order-No. 02-200-05-000

Code: Order-No.: HJ 200 SB O - Z12 - ZAV - 44 02-200-05-005 HJ 200 SB O - Z12 - ZAH - 44 02-200-05-006 HJ 200 SB O - Z12 - ZAV - 48 02-200-05-008 HJ 200 SB O - Z12 - ZAH - 48 02-200-05-009 HJ 200 SB O - Z12 - WSHB 02-200-05-004 HJ 200 SB O - Z12 - WSV 02-200-05-002 HJ 200 SB O - Z12 - WSH 02-200-05-003

identical nomenclature for HJ 200 SB O - Z12, left, Order-No. 02-201-05-000 5.1 Overspeed governor HJ 200 SB O - Z12 - P Order-No. 02-200-05-001

Code: Order-No.: HJ 200 SB O - Z12 - P - ZAV - 44 02-200-05-015 HJ 200 SB O - Z12 - P - ZAH - 44 02-200-05-016 HJ 200 SB O - Z12 - P - ZAV - 48 02-200-05-018 HJ 200 SB O - Z12 - P - ZAH - 48 02-200-05-019 HJ 200 SB O - Z12 - P - WSHB 02-200-05-014 HJ 200 SB O - Z12 - P - WSV 02-200-05-012 HJ 200 SB O - Z12 - P - WSH 02-200-05-013

identical nomenclature for HJ 200 SB O - Z12 - P, left, Order-No. 02-201-05-001 5.2. Overspeed governor HJ 200 SB O - Z12 - H Order-No. 02-200-05-007

Code: Order-No.: HJ 200 SB O - Z12 - H - ZAV - 44 02-200-05-075 HJ 200 SB O - Z12 - H - ZAH - 44 02-200-05-076 HJ 200 SB O - Z12 - H - ZAV - 48 02-200-05-078 HJ 200 SB O - Z12 - H - ZAH - 48 02-200-05-079 HJ 200 SB O - Z12 - H - WSHB 02-200-05-074 HJ 200 SB O - Z12 - H - WSV 02-200-05-072 HJ 200 SB O - Z12 - H - WSH 02-200-05-073

identical nomenclature for HJ 200 SB O - Z12 - H, left, Order-No. 02-201-05-007 5.3. Overspeed governor HJ 200 SB O - Z12 - P - H Order-No. 02-200-05-017

Code: Order-No.: HJ 200 SB O - Z12 - P - H - ZAV - 44 02-200-05-175 HJ 200 SB O - Z12 - P - H - ZAH - 44 02-200-05-176 HJ 200 SB O - Z12 - P - H - ZAV - 48 02-200-05-178 HJ 200 SB O - Z12 - P - H - ZAH - 48 02-200-05-179 HJ 200 SB O - Z12 - P - H - WSHB 02-200-05-174 HJ 200 SB O - Z12 - P - H - WSV 02-200-05-172 HJ 200 SB O - Z12 - P - H - WSH 02-200-05-173

identical nomenclature for HJ 200 SB O - Z12 - P - H, left, Order-No. 02-201-05-017



6. Overspeed governor HJ 200 SB U - Z12 , Order-No. 02-200-06-000

Code: Order-No.: HJ 200 SB U - Z12 – ZAV - 44 02-200-06-005 HJ 200 SB U - Z12 – ZAH - 44 02-200-06-006 HJ 200 SB U - Z12 – ZAV - 48 02-200-06-008 HJ 200 SB U - Z12 – ZAH - 48 02-200-06-009 HJ 200 SB U - Z12 - WSHB 02-200-06-004 HJ 200 SB U - Z12 - WSV 02-200-06-002 HJ 200 SB U - Z12 - WSH 02-200-06-003

identical nomenclature for HJ 200 SB U - Z12, left, Order-No. 02-201-06-000 6.1 Overspeed governor HJ 200 SB U - Z12 - P Order-No. 02-200-06-001

Code: Order-No.: HJ 200 SB U - Z12 - P - ZAV - 44 02-200-06-015 HJ 200 SB U - Z12 - P - ZAH - 44 02-200-06-016 HJ 200 SB U - Z12 - P - ZAV - 48 02-200-06-018 HJ 200 SB U - Z12 - P - ZAH - 48 02-200-06-019 HJ 200 SB U - Z12 - P - WSHB 02-200-06-014 HJ 200 SB U - Z12 - P - WSV 02-200-06-012 HJ 200 SB U - Z12 - P - WSH 02-200-06-013

identical nomenclature for HJ 200 SB U - Z12 - P, left, Order-No. 02-201-06-001



Appendix 2: Technical drawings

Description Drawing -No. HJ 200 SB O 02-202-01-000 HJ 200 SB U 02-202-02-000 HJ 200 SB O - Z6 02-200-03-000 HJ 200 SB U - Z6 02-200-04-000 HJ 200 SB O - Z12 02-200-05-000 HJ 200 SB U - Z12 02-200-06-000 HJ 200 SB O - P 02-202-01-001 HJ 200 SB O - WSHB 02-202-01-004 HJ 200 SB O - ZAV 44 02-202-01-005 HJ 200 SB O - H 02-202-01-007 Adapter plate 200 - N 02-21-001 Adapter plate 200 - N - P 02-21-011 Creeping protection - AS kit A3 02-21-020 Kombi design - K 02-21-003 Kombi design - K -P 02-21-009 Remote triggering - FG 02-21-004 Safety switch ---

Translation of the German terms on the drawings:

German English Absinkverhinderung Creeping protection Anbaubeispiel Add-on example Anschlussempfehlung Connection suggestion Auslösegeschwindigkeit Tripping speed Einziehen der Fangvorrichtung Retraction of the safety gear Fangschalter Contact safety gear Hauptschütze Master contactor Hilfsschalter am Verriegelungsschutz Auxiliary contact for locking device protection Hilfsstromquelle Auxiliary current Hubmagnet Absinkv. Solenoid creeping protection Linke Ausführung / Drehrichtung gezeichnet Drawing of the left version / release direction Notendabschaltung Control current end switch Rechte Ausführung spiegelbildlich Right version / release direction reversed image Riegelkurve Locking curve Riegelschalter Locking contact Seildurchmesser Rope diameter governor rope Sicherheitsschalter Safety switch Türschalter Contact door Überwachungsschalter für M Switch for solenoid Zeitrelais Timing relay

overspeed governors and accessories product...

Documents