owner’s manualheos 7heos 5 heos 3 - denonowner’s manualheos 7heos 5 heos 3. contents setup use...

.

Wireless Speaker

Owner’s ManualHEOS 7HEOS 5HEOS 3

.

Contents Setup Use Troubleshooting Status LED Appendix

1

INTRODUCTION 6BEFORE YOU BEGIN 7

System Requirements 7Network Requirements 7Controller Requirements 8

Getting To Know Your Speaker 9Front panel 10Controls 11Back panel 12

Placing Your HEOS device 13Wall or Ceiling Mounting (HEOS 3 only) 13

Powering Your Speaker 14Getting the HEOS App 14

SETTING UP YOUR FIRST HEOS SPEAKER 15ADDING MORE HEOS DEVICES 16

Adding Wired Speakers 16Adding Wireless HEOS devices 16

USING YOUR HEOS DEVICE 17Selecting a Room/Speaker 17Listening to Radio 18Playing music stored on your mobile device 18Playing music from your networked PC or NAS 19Playing music from the AUX input 20Playing music from a USB device 21HEOS account 22

What is a HEOS account? 22Why do I need a HEOS account? 22Signing up for a HEOS account 22Changing Your HEOS account 22

Playing from Streaming Music Services 23Adding a Music Service 23Changing Music Service Settings 23

Managing Inputs 24Changing the Name of the Inputs 24Hiding an Input 24

Managing your Phone 25Using Headphones (HEOS 7 only) 25Listening To The Same Music In Multiple Rooms 26

Grouping Rooms 26Ungrouping Rooms 27Grouping All Rooms (Party Mode) 28Ungrouping All Rooms 29

Stereo Pairing 30Creating a Stereo Pair 30Changing the Name of a Stereo Pair 32Adjusting the Balance 32

Contents Setup Use Troubleshooting Status LED AppendixContents

2

Swapping Left and Right Channels in a Stereo Pair 33Removing a Stereo Pair 33

Using the Now Playing Queue 34Play Now 34Play Now & Replace Queue 34Play Next 34Add to End of Queue 34

Rearranging the Now Playing Queue 35Deleting Songs from the Play Queue 35Deleting All Songs from the Play Queue 36Saving Playlists 36Performing Repeat and Shuffle Playback 36

MAKING SPEAKER ADJUSTMENTS 37Changing the Name of a Speaker 37Changing the Wireless Network Connection 37Changing the Speaker’s Equalizer 38Changing the Speaker’s Orientation (HEOS 3 Only) 38Adjusting the Audio Quality 38Adjusting the Status Light Brightness 38Advanced Speaker Settings 39

Network Settings 39About Wireless Power Saving 39Firmware Upgrade 40About 40


3

UPDATING YOUR SYSTEM 41ADVANCED FEATURES 42

Submit Diagnostics 42Sharing Music from your Mobile Device 42Resetting Your Controller App 42

POWER MANAGEMENT 43Power Modes 43

Network Standby 43Deep Standby 43Off 43

BASIC TROUBLESHOOTING 44My speaker won’t connect to my network using the audio cable 44I get a message “Device was not found” 44Music cuts out or delays sometimes 45I hear a delay when using the AUX Input with my TV 45Connecting to a WPS Network 46Resetting Your Speaker 46Restoring the Speaker to Factory Defaults 47Contact Denon 48


4

Status LED Table 49Supported File Types and Codecs 55SPECIFICATIONS 56

Speaker Specifications 56HEOS 7 56HEOS 5 57HEOS 3 58

INFORMATION 59Trademarks 59License 60

License Information for the Software Used in the Unit 60


5

Thank you for purchasing this HEOS product. To ensure proper operation, please read this owner’s manual carefully before using the product.

NOTETHIS DOCUMENT CONTAINS INFORMATION THAT IS SUBJECT TO CHANGE WITHOUT NOTICE.For latest information, please visit HEOSbyDenon.com

INTRODUCTIONThe HEOS speaker is part of the HEOS wireless multi-room sound system that enables you to enjoy your favorite music anywhere and everywherearound your home. By utilizing your existing home network and the HEOS app on your iOS or Android™ device, you can explore, browse, and play musicfrom your own music library or from many online streaming music services.0 True multi-room audio - play different songs in different rooms or the same song in every room0 Utilizes your existing home wireless network for quick and easy setup0 Industry leading microsecond audio synchronization between HEOS device0 Legendary Denon audio qualityIf you are in a hurry, you can be enjoying great sounding music in no time by following the steps outlined in the HEOS Quick Start Guide (packaged withyour HEOS device).

[Example] HEOS 5

.

HEOS 5 QUICK START GUIDE

Please continue reading this Owner’s Manual for more detailed information about the features and benefits of your HEOS Speaker.


6

BEFORE YOU BEGINNOTE

If you have already installed at least one HEOS device, please skip to the section “ADDING MORE HEOS DEVICES” (v p. 16).

System RequirementsBefore you begin installing your first HEOS speaker, please make sure you understand and meet a few basic requirements.

o Network RequirementsWireless Router - In order to use your HEOS music system, you should have a working wireless (Wi-Fi) network in your home. If you do not have awireless network, please contact your local Denon dealer or electronics retailer to assist you with purchasing and installing a wireless network in yourhome.

.

The HEOS Extend Wireless Range Extender (sold separately) is available as an accessory, shouldyou need to setup a new wireless network or extend the range of your existing network. Pleasecontact Denon for more information about the Wireless Extender.

High Speed Internet Connection - HEOS accesses the Internet to stream music to your home from many popular online music services. HEOS isalso designed to provide you with software updates, which are delivered via your home Internet connection. DSL, Cable, and Fiber services willprovide the best experience and reliability. You may experience performance issues with slower Internet connections like satellite based services.


7

o Controller RequirementsYou can control your HEOS wireless multi-room sound system using the free HEOS app on any iOS or Android mobile device that meets theseminimum requirements:

.

iOS Minimum Requirements0 iOS version 7.0 or later0 iPhone® 4 or newer0 iPad® 2 or newer0 iPod touch® (5th generation) or newer

.

Android Minimum Requirements0 Android OS version 2.3 or later0 All resolutions


8

Getting To Know Your SpeakerUnpack your speaker from the box and verify that the following items are included:

.

q

w e r t y

u i o

(European model only)

(North America model only)

Power supply(for HEOS 3)

or

Power supply and Power cord(for HEOS 7/5)

Ethernet cable

oror

HEOS Speaker

Quick Start Guide Safety Instructions Warranty(North America model only)

Extended Protection Plan(North America model only)

Audio/Setup cable

HEOS 7 HEOS 5 HEOS 3

QUICK STRT GUIDE

NOTEPlease use the power supply and power cord included in the box for your device.


9

o Front panel

.

w

qq

w

q

w


A SpeakersB Status LED

Please refer to the “Status LED Table” for LED color and state meaning “Status LED Table” (v p. 49).


10

o Controls

.

qw

e

qw

w

q


A Volume Up/Down buttons (+, –)Adjusts the HEOS device’s volume level up or down.

B Mute button (:)Mutes or unmutes the HEOS device’s volume.

C Headphone output (HEOS 7 only)The music will stop playing through the built in speakers when you insert the headphones and turn back on when you remove the headphones.See (v p. 25).


11

o Back panel

.

e t ur

qw y

e t ur

qw y DC18V

2.0ARESET AUX IN 5V/1AUSB

NETWORK CONNECT

w

i

o

qe t ur y


A Power Input (DC IN)Used to connect the external power supply (v p. 14).

B Reset Button (RESET)Various settings are reset to the factory default values (v p. 46).

C AUX Input (AUX IN)Used to connect audio devices (v p. 20).Used to add the speaker to your wireless network (v p. 16).

D USB Input (USB 5V/1A)Used to connect USB storage devices.

E Network Connector (NETWORK)Used to connect this unit to a wired Ethernet network (v p. 16).

F Connect Button (CONNECT)Used for Wi-Fi setup (v p. 46).

G Connect in Status LEDIndicates the status of this unit (v p. 46, 49).

H Threaded Mounting HoleUsed to mount this unit on a wall or ceiling.

I Safety Wiring HoleUsed to prevent from dropping.


12

Placing Your HEOS deviceYou can place your HEOS device anywhere you want to enjoy great sounding music. Please follow these simple guidelines when determining where toplace your speaker…0 The HEOS device must be within range of your wireless network.0 The HEOS speaker is designed to sound best when placed 3 to 12 inches (8 - 30 cm) from a wall.0 Locate the speaker at least 12 inches (30 cm) from a television, computer, or other display device to avoid the possibility of interference.0 Place the speaker across the room from where you will be listening, as close to ear level as possible.0 The HEOS device is not waterproof. Do not place it near any water source and do not leave it outside in the rain or snow.

o Wall or Ceiling Mounting (HEOS 3 only)The HEOS 3 speaker can optionally be mounted on a wall or ceiling using standard 1/4 inches (6.35 mm) threaded speaker or camera mounts whichsupport up to 10 lbs (4.5 kg). Please visit your local Denon dealer or electronics retailer for more information about possible wall and ceiling mountingoptions.

CautionRecommend installing a safety wire (not included) at the safety wiring hole on the back of the speaker in order to prevent injury to the user and othersor damage to property should the speaker fall for some reason.


13

Powering Your SpeakerConnect the power cord included in the box to the back of the speaker and the plug to a wall outlet. The speaker is capable of automatically switchingbetween 100 - 240 V.

.


DC18V2.0ARESET AUX IN 5V/1A

USBNETWORK CONNECT

Getting the HEOS AppThe HEOS app is the heart of the HEOS experience. Using your mobile device and the HEOS app, you can setup, browse, explore, and control yourHEOS system right in the palm of your hand, from anywhere in your home.Download the HEOS app for iOS or Android by searching App StoreSM or Google Play™ store for “HEOS by Denon”.

.

For the purpose of improvement, the specifications and design are subject to change without notice.


14

SETTING UP YOUR FIRST HEOS SPEAKEROnce you have placed your speaker in your listening room and have downloaded the HEOS app, you are ready to configure your speaker for musicplayback. This involves following a few simple steps to get the speaker connected to your existing home network:

CautionDO NOT connect the Ethernet cable if you are connecting your speaker to a wireless network. If you are connecting the speaker to a wired network, usean Ethernet cable to connect the speaker to your network or router.

1 Make sure your mobile device is connected to yourwireless network (the same network you want yourspeakers connected to). You can check this in theSettings - Wi-Fi menu of your iOS or Android device.

NOTEIf your wireless network is secure, make sure you know the password to joinyour network.

2 Make sure you have the includedAudio/Setup cable handy.

3 Launch the HEOS app on yourmobile device.

4 Tap the “Setup Now” button at the top of the screen.

5 Follow the instructions to add the speaker to yourwireless network. (The Wi-Fi settings from your mobiledevice will be copied to the speaker via the audiocable.)

NOTEIf you have any problems connecting your HEOS device, jump to theTroubleshooting section (v p. 44).

Contents Setup Use Troubleshooting Status LED AppendixSetup

15

ADDING MORE HEOS DEVICESThe HEOS wireless multi-room sound system is a true multiroom audio system that automatically synchronizes audio playback between multiple HEOSdevices so that the audio coming from different rooms is perfectly in sync and always sounds amazing! You can easily add up to 32 HEOS devices to yourHEOS system.

Adding Wired SpeakersJust connect the HEOS device to your home network using an Ethernet cable and the HEOS device will appear on your HEOS app as a new room in theRooms screen.At your convenience, you can assign a name to the HEOS device to indicate which room you have it placed in.

0 Use only a shielded STP or ScTP LAN cable which is easily available at electronics stores (CAT-5 or greater recommended).0 Do not connect a Network Connector directly to the LAN port/Ethernet connector on your computer.

Adding Wireless HEOS devicesYou can add additional wireless HEOS devices to your HEOS system by selecting “Add Device” from the HEOS app’s settings menu and follow theinstructions:

.

1 2Music

Add Device

SettingsMusic


16

USING YOUR HEOS DEVICEOnce you have your HEOS device connected to your network and the HEOS app installed on your mobile device, it’s easy to start enjoying your favoritemusic. You can listen to something different on every HEOS devices or the same music perfectly synchronized on all HEOS devices. It’s up to you!

Selecting a Room/SpeakerIf you have more than one HEOS device, you must tell the HEOS systemwhich HEOS device you want to control:

1 Tap the Rooms tab.

2 Select the Room/Speaker you want to control.

3 Select the Music tab to select a music source or theNow Playing tab to control what is currently playing inthe selected room.

.

1

2

3Now PlayingMusicRooms

Song Name 5

Song Name 4

Song Name 3

Song Name 2

Song Name 1

Outside

Bedroom

Dining

Living

Kitchen

Drag one room into another to group them

Rooms

Contents Setup Use Troubleshooting Status LED AppendixUse

17

Listening to RadioThe HEOS system includes access to more than 100,000 free internetradio streams from all corners of the globe via the TuneIn radio service.Just select the TuneIn logo from the main Music menu and browse amongthe 100,000 stations neatly organized into popular categories and select astation that appeals to your mood.

NOTEIf you have a TuneIn account, you can sign into the TuneIn service under Settings -Music Sources - TuneIn, and access all of your “My Favorites” TuneIn stations.

.

Audio signal

Playing music stored on your mobiledevice

1 Tap the “Music” tab.

2 Select “This iPhone/iPod/iPad/Phone”.

3 Browse the local music on your phone and selectsomething to play.

.

Audio signal


18

Playing music from your networked PCor NAS

1 Select “Music Servers” from the Music tab.

2 Select the name of your networked PC or NAS (networkattached storage) server.

3 Browse the music on your PC/NAS and selectsomething to play.

.

NAS(Network AttachedPC Storage)PC

Audio signal


19

Playing music from the AUX input

1 Connect an audio device with a 3.5 mm stereo audiooutput to the AUX input on your speaker using theincluded 3.5 mm stereo audio cable.When a stereo audio cable is connected to AUX IN, the sourceautomatically switches to Inputs.

NOTEWhen there is a cable connected to AUX IN, select “Inputs” from the Musictab.

2 Initiate playback on the audio device.

The sound from the audio device can be played directly on the selected speaker ordigitized and sent over your network to other speakers.

NOTEThe analog output signals from some sources can be fairly strong. If the input level ofthe source device is turned up high, it could overload the inputs of the HEOS device.This is unlikely to cause damage, but can cause distorted sound. Initially, set thevolume of the source to a medium – low level, then turn it up as needed. If you heardistortion, turn down the device's volume control.

.

Audio signal


20

Playing music from a USB device1 Insert a FAT32 formatted USB device into the USB port

on the back of the HEOS system.

2 Select “USB Music” from the “Music” tab.

3 Select the name of your HEOS system.

4 Browse the music on your USB device and selectsomething to play.

NOTE0 It may take several minutes for the name of your HEOS device to appear in the

“USB Music” list if you have a large number of files on your USB device.0 It is not possible to connect and use a computer via the USB port of this unit using

a USB cable.

.

Audio signal


21

HEOS accounto What is a HEOS account?

A HEOS account is master account or “keychain” for managing all ofyour HEOS music services with one single username and password.

o Why do I need a HEOS account?With the HEOS account you just have to enter your music serviceslogin names and passwords one time. This allows you to easily andquickly use multiple controller apps on different devices. You just loginto your HEOS account on any device and you will have access to allof your associated music services, play history and custom playlists,even if you are at a friend’s house listening to music on their HEOSsystem.

o Signing up for a HEOS accountYou will be instructed to signup for a HEOS account the first time youtry to access any music service from the main Music menu of theHEOS app.

o Changing Your HEOS account1 Tap the Music tab.

2 Select the Settings a icon in the upper left corner ofthe screen.

3 Select “HEOS Account”.

4 Change your location, change your password, deleteyour account or sign out of your account.


22

Playing from Streaming Music ServicesA Music Service is an online music company that provides access to vastmusic collections via free and/or paid subscriptions. Depending upon yourgeographical location, there are several options to choose from. For moreinformation about which services are available in your area please visitHEOSbyDenon.com

o Adding a Music ServiceOnce you’ve setup your HEOS account, you can add supported MusicServices to your HEOS system by tapping on the music service logo inthe Music tab.Follow the instructions on the screen to add your username andpassword for the selected music service. You only have to enter youraccount information once as the HEOS account service will securelyremember your login information so you don’t have to enter it eachtime you want to play music from the music service.Additional Music Services may be available under Settings - MusicServices.

o Changing Music Service Settings1 Tap the “Music” tab.

2 Select the Settings a icon in the upper left corner ofthe screen.

3 Select “Music Sources”.

4 Select “Online Music”.

5 Select the name of the online Music Service you wantto edit.

6 Sign out, then sign in again to associate yourusername and password with your HEOS account.

7 Select “Hide for Now” to prevent the service logo fromappearing on the main Music menu.


23

Managing InputsIf you connected external audio source components (like CD players,portable music players, Cable Boxes, etc...) to any of your HEOSspeakers inputs, you can rename the default input names to describe theactual source or hide any inputs that are not being used.

1 Select the Settings a icon located in the upper leftcorner of the main Music menu to display the Settingsmenu.


3 Select “Inputs”.

4 Select the speaker which you connect your externalaudio source device to.

o Changing the Name of the Inputs1 Select the name of the input you want to edit.

2 Select "Name".

3 Select or enter a new name to describe the source thatyou connected.

4 Select the Save button to save your changes.

o Hiding an Input1 Select the name of the input you want to edit.

2 Toggle “Hide Input” to ON to prevent this input fromappearing under the Inputs tile on the main Musicmenu.


24

Managing your PhoneYour smartphone or tablet can be hidden if it does not need to be in the“Music Sources” menu.



3 Select “This iPhone/iPod/iPad/Phone”.

4 Toggle “This iPhone/iPod/iPad/Phone” to OFF toprevent the service logo from appearing on the mainMusic menu.

Using Headphones (HEOS 7 only)You can listen to music through headphones by connecting your favoriteheadphones to the 3.5 mm headphone jack on the side of the HEOS 7speaker. The music will stop playing through the built in speakers whenyou insert your headphones into the jack, and turn back on when youremove the headphones.

.

NOTETo prevent hearing loss, do not raise the volume level excessively when usingheadphones.


25

Listening To The Same Music InMultiple Rooms

The HEOS system is a true multiroom audio system that automaticallysynchronizes audio playback between multiple HEOS devices so that theaudio coming from different rooms is perfectly in sync and always soundsamazing!You can easily add up to 32 HEOS devices to your HEOS system.You can join or group up to 16 individual HEOS devices into a group ofHEOS devices that function as if they were a single HEOS device.

o Grouping Rooms

1 Tap the “Rooms” tab.

2 Press and hold your finger on room that is not playingmusic.

3 Drag it into the room that is playing music (indicated bythe red outline) and lift your finger.

4 The two rooms will be grouped together into a singledevice group and both rooms will be playing the samemusic in perfect sync.

.

1

324

Now PlayingMusicRooms

Song Name 1Dining

Kitchen


Rooms


Song Name 3

Song Name 3

Song Name 2

Song Name 2

Song Name 1

Bedroom

Bedroom

Dining

Living

Kitchen


Rooms

Living

Drag a room out of this group to ungroup it

Living+Kitchen


26

o Ungrouping Rooms


2 Press and hold your finger on room that you want toremove from the group.

NOTEYou can not remove the first room that started playing the music beforegrouping.

3 Drag it out of the group and lift your finger.

4 Music will stop playing in the room you dragged out ofthe group but will continue playing in any remainingrooms.

.

1

324


Song Name 3

Song Name 2

Song Name 1

Bedroom

Dining

Living

Kitchen


Rooms


Song Name 4

Song Name 3

Song Name 2

Song Name 1

Bedroom

Dining

Living

Kitchen


Rooms

Living


27

o Grouping All Rooms (Party Mode)You can easily group the eight rooms together into Party Mode byusing a “pinch” gesture.


2 Place two fingers on the screen over the list of rooms.

3 Quickly pinch your two fingers together and release.

4 All of your rooms will be joined together and beginplaying the same music in perfect sync.

.

1

2

3

4


Song Name 1

Bedroom

Dining

Kitchen


Rooms


Song Name 4

Song Name 3

Song Name 2

Song Name 1

Bedroom

Dining

Living

Kitchen


Rooms

Living


Dining+Living+...


28

o Ungrouping All RoomsYou can easily ungroup all of your rooms and exit Party Mode by usinga “spread” gesture.


2 Place two fingers close together on the screen over listof rooms.

3 Quickly spread your two fingers apart from each otherand release.

4 All of your rooms will be ungrouped and music willstop playing in every room (except the original“master” room that was playing before you groupedthe rooms together).

.

1

2

3 4


Song Name 1

Bedroom

Dining

Dining

Kitchen


Rooms


Song Name 4

Song Name 3

Song Name 2

Song Name 1

Bedroom

Dining

Living

Kitchen


Rooms

Living



29

Stereo Pairingo Creating a Stereo PairA matching pair of HEOS 3, HEOS 5 or HEOS 7 speakers that have beengrouped together (see above) can be saved as a persistent stereo pairwhere one speaker outputs the left channel of audio and the other speakeroutputs the right channel of audio. Paired speakers will then appear as asingle Room (with two speakers playing music) in the Rooms list.


2 Create a group containing ONLY two matchingspeakers (see “Grouping Rooms” (v p. 26)).

3 Tap the Pencil e icon to enter Edit mode.

4 Tap on the Group of two matching speakers to Edit theGroup.

.

1

32 4

Song Name 3


Song Name 2

Bedroom

Kitchen

Dining L

Dining R


Rooms

Song Name 1Dining L + Dining R

Edit Rooms

Dining L

Dining R

Song Name 2Kitchen

Song Name 3Bedroom

Song Name 2


30

5 Tap on the Stereo Pair switch to pair the two speakers.

6 Tap the Back arrow to return to the list of Rooms.

7 Tap the Check Mark i icon to exit Edit mode.

The group of two matching speakers will now appear as a single Room.You can change the name of the stereo paired room at any time.

For optimal sound quality, please change the Orientation setting of the HEOS 3speakers to “Vertical” before turning on stereo pairing.

.

56

Rooms


Rooms

Now PlayingMusic

Song Name 3Bedroom

Song Name 1Dining L + Dining R

Song Name 2Kitchen

Edit Group

Name Dining L + Dining R

Stereo Pair

EQ

Balance Center

Swap L&R


31

o Changing the Name of a Stereo Pair



3 Tap a Stereo Pair (a room which contains two matchingHEOS speakers) to edit the group.

4 Tap “Name”.

5 Select or enter a new name for your pair of speakers.

6 Tap the Save i button to save your changes.

o Adjusting the Balance




4 Select “Balance”.

5 Adjust the Balance to the left or right.



32

o Swapping Left and Right Channels in a StereoPair




4 Tap on the Swap L&R switch to swap the left and rightchannels of the two speakers.



o Removing a Stereo Pair




4 Tap on the Stereo Pair switch to return the pairedspeakers to two individual speakers.




33

Using the Now Playing QueueHEOS uses a Now Playing “Queue” to line up music that you want to listen to. Music can be selected from any of your local or online music sources (aslong as they are not preprogrammed “radio” or “station” type streams). This feature works similarly to how a jukebox works. You select something to play(a song, album, playlist or even your entire music collection) and add it to the “Queue”. When you select something to play you will be asked how you wantto queue up your music.

.

Play AIbum

Track 66 0:20

Play Now

MusicRooms Now PlayingCancel

Play Now & Replace Queue

Play Next

Add to End of Queue

Track 11

Track 22

Track 1HEOS Device

Album

0:20

0:20

1

Track 22

Track 33

Track 44

Track 55

HEOS Device

0:19

0:20

0:20

0:20

0:20

MusicRooms Now Playing

Track 1

Album

HEOS Device

MusicRooms Now Playing

e r t

w

y

q

A Queue MenuWhen you select something to play you will be asked how you want toqueue up your music.

B Queue iconC Pencil iconD Delete iconE Save iconF Cover art or HEOS icon

You can return to the Now Playing screen display by tapping the coverart or the HEOS icon.

o Play NowInserts the item into the queue after the currently playing track andplays the selected item immediately.

o Play Now & Replace QueueClears the queue and plays the selected item immediately.

o Play NextInserts the item into the queue after the current song and plays it whenthe current song ends.

o Add to End of QueueAdds the item to the end of the queue.


34

Rearranging the Now Playing QueueOnce you have songs lined up in your queue, you might want to rearrangethe order or remove some songs:

1 Tap the “Now Playing” tab.

2 Tap the Queue d icon in the upper right corner of thescreen.


4 Rearrange the order of your queue by dragging the listf icon (on the right side of each track row) up ordown.

Deleting Songs from the Play QueueYou can remove songs one at a time from the Now Playing queue:




4 Tap the track(s) that you want to delete.

5 Tap the Delete g icon to delete all of the selectedtracks from the play queue.


35

Deleting All Songs from the Play QueueYou can remove all of the songs from the Now Playing queue:



3 Tap the Delete g icon to confirm that you want todelete all songs from the queue.

Saving PlaylistsYou can save the Now Playing queue as a HEOS Playlist that you canrecall later. The new playlist will be available from the Playlists button onthe Music tab on every controller app connected to your HEOS system.



3 Tap on the Save h icon.

4 Enter a name for your Playlist and tap the Save icon.

Performing Repeat and ShufflePlayback

The playback controls are visible on the Now Playing screen.


2 Tap the cover art to reveal the repeat b and shuffle ccontrols.


36

MAKING SPEAKER ADJUSTMENTSYou can adjust specific settings for each of your HEOS Speakers in yoursystem:


2 Select “My Devices” to display a list of your HEOSdevices.

3 Select the speaker you want to adjust.

Changing the Name of a Speaker1 Select “Name”.

2 Select or enter a new name for your speaker.

3 Tap the “Next” to save your changes.

Changing the Wireless NetworkConnection

1 Select “Network”.

2 A list of wireless networks that your speaker canaccess is displayed.

3 Select the network you want your speaker to join.

4 Wait as the speaker’s network connection is changed.

NOTEWired networking is automatically selected when the speaker is connected to a wiredEthernet network. To switch back to using a wireless network you must remove theEthernet cable from the back of the speaker.


37

Changing the Speaker’s Equalizer1 Select “EQ”.

2 Adjust the Treble or Bass up or down.

NOTESelect the Reset button to restore the default settings.

Changing the Speaker’s Orientation(HEOS 3 Only)

The HEOS 3 can be placed both vertically and horizontally.Each orientation has it’s own sound tuning and should be set accordinglyfor optimal sound quality.

1 Select “Orientation”.

2 Select “Vertical” if you placed your HEOS 3 vertically orselect “Horizontal” if you placed your HEOS 3horizontally.

3 Select the Back button and your settings areautomatically saved.

Adjusting the Audio QualitySelects the transcoding option for rebroadcasting audio from one HEOSdevice to another HEOS device (or group of devices) across the network.When set to “Normal”, high bit rate audio sources originating from the firstdevice (such as AUX input, WAV, FLAC and PCM) will be transcoded toensure the highest level of reliability for the audio stream.

1 Select “Quality”.

2 Select Normal (default) or High.

0 If you have selected High and you experience audio dropouts when streamingsources from one device to other devices, please select Normal (default).

0 This setting does not affect the AUX input when played on the connected deviceby itself (there are no other devices grouped to it), in which case the originalsource quality and bit rate are maintained and there is no inherent delay.

Adjusting the Status Light Brightness

1 Select “Status Light”.

2 Adjust the brightness up or down or set the slider tothe OFF position to completely disable the status light.


38

Advanced Speaker SettingsCaution

Adjusting these settings may disconnect your speaker from your networkand possibly render your speaker unusable. Do not use these featuresunless you are comfortable making advanced adjustments to yourspeaker.

o Network Settings1 Select “Advanced”.

2 Select “NETWORK SETTINGS” tab.

3 Scroll down to see all of the options fora. Network Interface (Ethernet or Wireless)b. Wireless Settingsc. IP Address Settings (Automatic or Manual)d. Wireless Power Saving

4 Select Save Settings to apply the new settings orCancel Changes to revert to the previous settings.

o About Wireless Power SavingThe Wireless Power Savings feature saves power by turning off power tothe wireless radio inside the HEOS device when the device is connectedto an Ethernet network. If you disconnect the Ethernet cable from theHEOS device, Wireless Power Saving will automatically turn off and thewireless radio will turn on so that the HEOS device can be discovered overyour wireless network.

NOTE0 If Wireless Power Savings is ON, Wi-Fi power will be temporarily turned on when

accessing the My Devices/(My Devices)/Network screen in the HEOS app orwhenever the Connect button on the device is pressed.


39

o Firmware Upgrade1 Select “Advanced”.

2 Select “FIRMWARE UPGRADE” tab.

3 Manually check for a firmware upgrade.

o AboutViewing technical details about the HEOS device.

1 Select “Advanced”.

2 Select “ABOUT” tab.

3 Scroll down to see information about the speaker’sa. Hardwareb. Softwarec. Device


40

UPDATING YOUR SYSTEMHEOS has the ability to add enhancements and updated functionality via your high speed Internet connection. When such updates becomeavailable, you will be notified when you open the HEOS app. Follow the instructions on the screen to update the HEOS device and/or yourcontroller App.In the event that you wish to manually initiate an update, please follow these steps:


2 Select “Check for Update”.

3 Follow the instructions on screen to install anyavailable updates to your HEOS system.


41

ADVANCED FEATURESThere are a few advanced features of the HEOS system that you may want to explore once you become familiar with the basic operations. You canaccess the advanced features of the HEOS system by following these steps:


2 Select “Advanced Settings” to display a list theavailable settings.

Submit DiagnosticsIf you are having trouble with your network or HEOS system, you may beasked by Denon technical support personnel to select this option. Thisfeature will automatically send Denon technical support diagnosticinformation about your HEOS system.

NOTE0 No personal information is sent and your information will never be shared with

anyone.

Sharing Music from your Mobile DeviceThe HEOS App has a feature called “Music Sharing” which can share thelocal music stored on your mobile device to other HEOS app users on yourlocal network. To enable this feature, select Music Sharing, and set it on“ON”.The name of the device you are sharing from will appear as a music serverallowing other HEOS controller apps to browse and play music from theyour device.

Resetting Your Controller AppThis feature will reset the control app to its original state when you firstinstalled it on your mobile device without requiring you to remove,download, and reinstall it from the app store.


42

POWER MANAGEMENTPower Modeso Network Standby

To save power, the device will automatically enter “Network Standby”whenever there is no network access or playback for 20 minutes andwill automatically resume to full power whenever the device is selectedand playing music. The front panel LED will be dimmed during“Network Standby” as it is a fully automatic function.

o Deep StandbyThe device also has the ability to automatically enter “Deep Standby”whenever the wired or wireless network connection is removed formore than 60 minutes in Network Standby. The front panel LED willturn off during Deep Standby. To “wake” a HEOS device from DeepStandby, you must press the volume or mute buttons which willimmediately turn on the front panel LED.

o OffTo completely turn off the power to the device you must remove themains plug from the power outlet.


43

BASIC TROUBLESHOOTINGMy speaker won’t connect to my network using the audio cable

Solution Refer to Page0 Make sure your mobile device is connected to your wireless network before setting up your speaker. 150 Alternatively, you can connect your speaker to your network router using the included Ethernet cable. Once connected via

Ethernet, the HEOS by Denon App should recognize the speaker and you can manually move it to your wireless network usingSettings/My Devices/Device_Name/Advanced/Network Settings.

16

I get a message “Device was not found”Solution Refer to Page

0 Move your speaker closer to your wireless router. 130 Your speakers and controller device may not be on the same network. Verify that the controller device is on the same network

as your speakers. This is usually configured under the Settings feature on your device.If you have more than one network, your device may hop to a different network as you move around your home.

15

0 Make sure you don’t have any other electronic devices interfering with your wireless network signals. Microwave ovens,cordless phones, and some televisions can cause wireless network interference.

13

0 If your speakers are located far away from your router, consider adding a Wireless Range Extender like the HEOS Extend. 70 In case your wireless router is incompatible with HEOS speaker, please use the optional HEOS Extend Wireless Range

Extender and hard-wire it to your router.7

Contents Setup Use Troubleshooting Status LED AppendixTroubleshooting

44

Music cuts out or delays sometimesSolution Refer to Page

0 Make sure your Internet connection is operating correctly. If you are sharing your network with other users or devices, they maybe using most of your bandwidth (especially if they are streaming video).

7

0 Make sure your speakers are within range of your wireless network. 70 Make sure your speakers are not located near other electronic devices that could interfere with it’s wireless connectivity (like

microwave ovens, cordless phones, TVs, etc…).7

I hear a delay when using the AUX Input with my TVSolution Refer to Page

0 If you are connecting the AUX input with your cable or satellite box for enjoying TV audio through multiple HEOS speakers, youmay hear a delay between when you see someone speak and when you hear the audio. This is because the HEOS systemmust buffer the audio before it sends it out to the speakers so that it arrives at all speakers at the same time.

20

0 You can avoid this delay by listening only to the speaker which is directly connected to the set top box. －


45

Connecting to a WPS NetworkSolution Refer to Page

If your wireless router support WPS (Wi-Fi Protected Setup™) your HEOS Wireless Speaker can optionally connect to yournetwork using the “Push Button” method by following these steps:1. Press the WPS button on your router.2. Within 2 minutes, rapidly press the Connect button 3 times (within 2 seconds of each press).3. The LED on the front of the speaker will flash green for several seconds as it connects to your WPS router.4. When the connection is complete, the LED on the front of the speaker will turn solid blue.

7

Resetting Your SpeakerSolution Refer to Page

Resetting your speaker will clear out the wireless network info, EQ, and name but retain it’s current software. You will have to useSettings - Add Speaker to reconnect the speaker to your home network before it can be used.To reset your speaker, gently insert a small paperclip into the Reset button hole on the back of the speaker and hold it in until thefront LED begins to flash amber.

–


46

Restoring the Speaker to Factory DefaultsSolution Refer to Page

Restoring the HEOS device to its factory defaults will clear all of the settings and restore the original software which was installedat the factory.

Caution0 All settings will be erased and the software will likely be downgraded!To restore your HEOS device to the factory defaults, unplug the power cable from the back of the HEOS device. Insert a smallpaperclip into the Reset button hole on the back of the HEOS device, reconnect the power cable, and hold it in until the front LEDbegins to flash amber.

–

* For further information, please visit HEOSbyDenon.com


47

Contact DenonFor U.S. & Canada only:If you need further assistance with your HEOS product, please contact HEOS by Denon Customer Support Services below:Website: www.HEOSbyDenon.com/SupportEmail: [email protected] Chat: www.HEOSbyDenon.com/LiveChatTelephone: Toll Free (855) 499 2820(M-F 10:00AM to 10:00PM EST / Sat 12:00PM to 8:00PM EST)For the other region:If you need additional help in solving problems, please contact Denon customer service in your area or visit HEOSbyDenon.com


48

Status LED Table[Example] HEOS 5

Device Operation Description Front LED Action Rear LED Action

Off No AC power or Deep Standby.

(off).

(off)

Plug in Booting.

(blink).

(off)

On Ready-Configured and connected to your network.

(solid).

(off)

On Not Connected to your network.

(solid).

(solid)

Change Network Connecting to your network.

(blink).

(off)

Contents Setup Use Troubleshooting Status LED AppendixStatus LED

49


Setup

Not connected.

(solid).

(solid)

Connect button was pressed.

(blink).

(blink)

Cable connection is OK.

(solid).

(solid)

Connecting to your network.

(blink).

(off)


50


Configured and connected to your network.

(solid).

(off)

Error.

(solid).

(solid)

Update

Updating.

(blink).

(blink)

Rebooting.

(blink).

(off)

Ready-Configured and connected to your network.

(solid).

(off)


51


Reset

Soft reset - Clear user settings.

(fast blink).

(solid)

Hard reset - Factory restore.

(blink).

(solid)

Rebooting.

(blink).

(off)

Ready-Not Configured.

(solid).

(solid)


52


Errors

Firmware Error.

(slow blink (NOT fade)).

(off)

Hardware Error.

(fast blink).

(off)

Network Error.

(solid).

(solid)

Volume Change .

(quick blink).

(off)

Mute .

(slow blink).

(off)


53


WPS

a WPS session is active.

(fast blink).

(fast blink)

WPS connected.

(for 3 sec. solid).

(solid)

WPS time-out.

(for 3 sec. solid).

(solid)

Power Management

Network Standby.

(dimmed solid).

(off)

Deep Standby.

(off).

(off)


54

Supported File Types and CodecsFrequency Sample Rate File Extension Codec Bit Rates

32 kHz44.1 kHz48 kHz

16 bit wav PCM ---


16 bit mp3 MPEG-1 Audio Layer 3CBR/VBR 32 - 320 kbps


16 bit m4aaac AAC-LC 48 - 320 kbps


16 bit wma wma9CBR CBR:48 - 192 kbps

44.1 kHz48 kHz 16 bit flac flac ---44.1 kHz48 kHz 16 bit m4a ALAC ---

NOTE0 Files protected by DRM such as Apple’s Fairplay DRM, are not supported.

Contents Setup Use Troubleshooting Status LED AppendixAppendix

55

SPECIFICATIONSSpeaker Specificationso HEOS 7

Wireless LANNetwork type: Conforming to IEEE 802.11a/b/g/nUsed frequency range: 2.4 GHz, 5 GHz

GeneralOperating temperature: 41 °F - 95 °F (5 °C - 35 °C)Power supply: AC 100 – 240 V, 50/60 HzPower consumption: 20WPower consumption in network standby mode: 4.5WPower consumption in deep standby mode: 0.3WMax Analog Input: 2 Vrms / 1 Vrms (switchblade)

DimensionsUnit : in. (mm)

.

7 63

/64

(203

)18 55/64 (479) 6 29/64 (164)

Weight: 6 lbs 3oz (2.8Kg)For the purpose of improvement, the specifications and design are subject to change without notice.


56

o HEOS 5Wireless LANNetwork type: Conforming to IEEE 802.11a/b/g/nUsed frequency range: 2.4 GHz, 5 GHz

GeneralOperating temperature: 41 °F - 95 °F (5 °C - 35 °C)Power supply: AC 100 – 240 V, 50/60 HzPower consumption: 23 WPower consumption in network standby mode: 4 WPower consumption in deep standby mode: 0.3 WMax Analog Input: 2 Vrms / 1 Vrms (switchblade)


.

8 15

/64

(209

)11 37/64 (294) 6 17/32 (166)

Weight : 6 lbs 9.8 oz (3.0 kg)For the purpose of improvement, the specifications and design are subject to change without notice.


57

o HEOS 3Wireless LANNetwork type: Conforming to IEEE 802.11a/b/g/nUsed frequency range: 2.4 GHz, 5 GHz

GeneralOperating temperature: 41 °F - 95 °F (5 °C - 35 °C)Power supply: AC 100 – 240 V, 50/60 HzPower consumption: 22 WPower consumption in network standby mode: 4 WPower consumption in deep standby mode: 0.3 WMax Analog Input: 2 Vrms / 1 Vrms (switchblade)


.

5 3/

64 (1

28)

10 53/64 (275) 6 9/64 (156) 5 1/8 (130) 6 1/2 (165)

10 2

3/32

(272

)5 5/

8 (1

43)

6 9/

64 (1

56)

Weight : 4 lbs 3.0 oz (1.9 kg)For the purpose of improvement, the specifications and design are subject to change without notice.


58

INFORMATIONTrademarks

.

Google Play is a trademark of Google Inc.

.

Apple, the Apple logo, iPad, iPhone, and iPod touch are trademarks ofApple Inc., registered in the U.S. and other countries. App Store is aservice mark of Apple Inc.

.

Wi-Fi Protected Setup™ logo is trademark of Wi-Fi Alliance.


59

Licenseo License Information for the Software Used inthe Unit

About GPL (GNU-General Public License), LGPL (GNU LesserGeneral Public License) LicenseThis product uses GPL/LGPL software and software made by othercompanies.After you purchase this product, you may procure, modify or distributethe source code of the GPL/LGPL software that is used in the product.Denon provides the source code based on the GPL and LPGLlicenses at the actual cost upon your request to our customer servicecenter. However, note that we make no guarantees concerning thesource code. Please also understand that we do not offer support forthe contents of the source code.This section describes software license used for this unit. Tomaintain the correct content, the original (English) is used.

n GPLOpen Source Used Version

bridge-utils 2.8busybox 1.21.1ebtables 2.0.10-4Linux kernel 2.6.30mtd-utils 1.4.3ntfs-3g_ntfsprogs 2011.4.12ntpclient 2007u-boot 2011.06wireless-tools version 29

n LGPLOpen Source Used Version

ffmpeg 0.8.3glibc 2.9libmms 0.6.2

n curl-7.24.0COPYRIGHT AND PERMISSION NOTICECopyright (c) 1996 - 2014, Daniel Stenberg, <[email protected]>.All rights reserved.Permission to use, copy, modify, and distribute this software for anypurpose with or without fee is hereby granted, provided that the abovecopyright notice and this permission notice appear in all copies.THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OFANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITEDTO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRDPARTY RIGHTS. IN NO EVENT SHALL THE AUTHORS ORCOPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGESOR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,TORT OR OTHERWISE, ARISING FROM, OUT OF OR INCONNECTION WITH THE SOFTWARE OR THE USE OR OTHERDEALINGS IN THE SOFTWARE.Except as contained in this notice, the name of a copyright holder shallnot be used in advertising or otherwise to promote the sale, use orother dealings in this Software without prior written authorization of thecopyright holder.


60

n e2fsprogs-libs-1.40.8/lib/uuidRedistribution and use in source and binary forms, with or withoutmodification, are permitted provided that the following conditions aremet:1. Redistributions of source code must retain the above copyright

notice, and the entire permission notice in its entirety, including thedisclaimer of warranties.

2. Redistributions in binary form must reproduce the above copyrightnotice, this list of conditions and the following disclaimer in thedocumentation and/or other materials provided with the distribution.

3. The name of the author may not be used to endorse or promoteproducts derived from this software without specific prior writtenpermission.

THIS SOFTWARE IS PROVIDED “AS IS” AND ANY EXPRESS ORIMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THEIMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE, ALL OF WHICH ARE HEREBYDISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FORANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSSOF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANYWAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF NOTADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

n expat-2.0.1Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltdand Clark CooperCopyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.Permission is hereby granted, free of charge, to any person obtaining acopy of this software and associated documentation files (the“Software”), to deal in the Software without restriction, includingwithout limitation the rights to use, copy, modify, merge, publish,distribute, sublicense, and/or sell copies of the Software, and to permitpersons to whom the Software is furnished to do so, subject to thefollowing conditions:The above copyright notice and this permission notice shall beincluded in all copies or substantial portions of the Software.THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OFANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITEDTO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE AND NONINFRINGEMENT.IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERSBE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,ARISING FROM, OUT OF OR IN CONNECTION WITH THESOFTWARE OR THE USE OR OTHER DEALINGS IN THESOFTWARE.


61

n getopthttp://cvsweb.netbsd.org/bsdweb.cgi/src/lib/libc/stdlib/Copyright (c) 1987, 1993, 1994 The Regents of the University ofCalifornia. All rights reserved.Redistribution and use in source and binary forms, with or withoutmodification, are permitted provided that the following conditions aremet:1. Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.2. Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in thedocumentation and/or other materials provided with the distribution.

3. Neither the name of the University nor the names of its contributorsmay be used to endorse or promote products derived from thissoftware without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS ANDCONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIEDWARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALLTHE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSSOF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANYWAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISEDOF THE POSSIBILITY OF SUCH DAMAGE.

n jQueryCopyright 2014 jQuery Foundation and other contributorshttp://jquery.com/Permission is hereby granted, free of charge, to any person obtaining acopy of this software and associated documentation files (the“Software”), to deal in the Software without restriction, includingwithout limitation the rights to use, copy, modify, merge, publish,distribute, sublicense, and/or sell copies of the Software, and to permitpersons to whom the Software is furnished to do so, subject to thefollowing conditions:The above copyright notice and this permission notice shall beincluded in all copies or substantial portions of the Software.THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OFANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITEDTO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENTSHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FORANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN ANACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USEOR OTHER DEALINGS IN THE SOFTWARE.


62

n libpcap-1.4.0License: BSDRedistribution and use in source and binary forms, with or withoutmodification, are permitted provided that the following conditions aremet:1. Redistributions of source code must retain the above copyright



3. The names of the authors may not be used to endorse or promoteproducts derived from this software without specific prior writtenpermission.

THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANYEXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUTLIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE.

n libtar-1.2.11Copyright (c) 1998-2003 University of Illinois Board of TrusteesCopyright (c) 1998-2003 Mark D. RothAll rights reserved.Developed by: Campus Information Technologies and EducationalServices, University of Illinois at Urbana-ChampaignPermission is hereby granted, free of charge, to any person obtaining acopy of this software and associated documentation files (the “Software”),to deal with the Software without restriction, including without limitationthe rights to use, copy, modify, merge, publish, distribute, sublicense,and/or sell copies of the Software, and to permit persons to whom theSoftware is furnished to do so, subject to the following conditions:zRedistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimers.zRedistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimers in thedocumentation and/or other materials provided with the distribution.

zNeither the names of Campus Information Technologies andEducational Services, University of Illinois at Urbana-Champaign,nor the names of its contributors may be used to endorse or promoteproducts derived from this Software without specific prior writtenpermission.

THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OFANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TOTHE WARRANTIES OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE AND NONINFRINGEMENT.IN NO EVENT SHALL THE CONTRIBUTORS OR COPYRIGHTHOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHERLIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OROTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITHTHE SOFTWARE OR THE USE OR OTHER DEALINGS WITH THESOFTWARE.


63

n mDNS 320.10.80The majority of the source code in the mDNSResponder project is licensedunder the terms of the Apache License, Version 2.0, available from:<http://www.apache.org/licenses/LICENSE-2.0>To accommodate license compatibility with the widest possible rangeof client code licenses, the shared library code, which is linked atruntime into the same address space as the client using it, is licensedunder the terms of the “Three-Clause BSD License”.The Linux Name Service Switch code, contributed by National ICTAustralia Ltd (NICTA) is licensed under the terms of the NICTA PublicSoftware Licence (which is substantially similar to the “Three-Clause BSDLicense”, with some additional language pertaining to Australian law).

n mongoosehttps://github.com/cesanta/mongoose/Copyright (c) 2004-2013 Sergey LyubkaPermission is hereby granted, free of charge, to any person obtaining acopy of this software and associated documentation files (the“Software”), to deal in the Software without restriction, includingwithout limitation the rights to use, copy, modify, merge, publish,distribute, sublicense, and/or sell copies of the Software, and to permitpersons to whom the Software is furnished to do so, subject to thefollowing conditions:The above copyright notice and this permission notice shall beincluded in all copies or substantial portions of the Software.THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OFANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITEDTO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENTSHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FORANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN ANACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USEOR OTHER DEALINGS IN THE SOFTWARE.


64

n openssl-1.0.0dCopyright (c) 1998-2011 The OpenSSL Project. All rights reserved.Redistribution and use in source and binary forms, with or withoutmodification, are permitted provided that the following conditions aremet:1. Redistributions of source code must retain the above copyright



3. All advertising materials mentioning features or use of this softwaremust display the following acknowledgment:“This product includes software developed by the OpenSSL Projectfor use in the OpenSSL Toolkit. (http://www.openssl.org/)”

4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not beused to endorse or promote products derived from this softwarewithout prior written permission. For written permission, pleasecontact [email protected].

5. Products derived from this software may not be called “OpenSSL”nor may “OpenSSL” appear in their names without prior writtenpermission of the OpenSSL Project.

6. Redistributions of any form whatsoever must retain the followingacknowledgment:“This product includes software developed by the OpenSSL Projectfor use in the OpenSSL Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “ASIS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIESOF MERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSLPROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT,INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSSOF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANYWAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISEDOF THE POSSIBILITY OF SUCH DAMAGE.This product includes cryptographic software written by Eric Young([email protected]). This product includes software written by TimHudson ([email protected]).


65

n portmap-6.0Copyright (c) 1990 The Regents of the University of California.zAll rights reserved.zRedistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions are met:1. Redistributions of source code must retain the above copyright



3. A ll advertising materials mentioning features or use of this softwaremust display the following acknowledgement:This product includes software developed by the University ofCalifornia, Berkeley and its contributors.

4. Neither the name of the University nor the names of its contributorsmay be used to endorse or promote products derived from thissoftware without specific prior written permission.

zTHIS SOFTWARE IS PROVIDED BY THE REGENTS ANDCONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIEDWARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALLTHE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OFUSE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHERIN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDINGNEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THEUSE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITYOF SUCH DAMAGE.

n pstdint.h-0.1.12zBSD License:zCopyright (c) 2005-2011 Paul HsiehzAll rights reserved.zRedistribution and use in source and binary forms, with or without

modification, are permitted provided that the following conditions aremet:

1. Redistributions of source code must retain the above copyrightnotice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyrightnotice, this list of conditions and the following disclaimer in thedocumentation and/or other materials provided with the distribution.

3. The name of the author may not be used to endorse or promoteproducts derived from this software without specific prior writtenpermission.

zTHIS SOFTWARE IS PROVIDED BY THE AUTHOR “AS IS” ANDANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUTNOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE ARE DISCLAIMED.

z IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANYDIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITEDTO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;LOSS OF USE, DATA, OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OFLIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, ORTORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING INANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IFADVISED OF THE POSSIBILITY OF SUCH DAMAGE.


66

n rl78flash 2000.3.1License=======The MIT License (MIT)Copyright (c) 2012 Maxim SalovPermission is hereby granted, free of charge, to any person obtaining acopy of this software and associated documentation files (the“Software”), to deal in the Software without restriction, includingwithout limitation the rights to use, copy, modify, merge, publish,distribute, sublicense, and/or sell copies of the Software, and to permitpersons to whom the Software is furnished to do so, subject to thefollowing conditions:The above copyright notice and this permission notice shall beincluded in all copies or substantial portions of the Software.THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OFANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITEDTO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENTSHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FORANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN ANACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USEOR OTHER DEALINGS IN THE SOFTWARE.

n sqlite 2003.5.7SQLite CopyrightSQLite is in thePublic DomainAll of the code and documentation in SQLite has been dedicated to thepublic domain by the authors. All code authors, and representatives ofthe companies they work for, have signed affidavits dedicating theircontributions to the public domain and originals of those signedaffidavits are stored in a firesafe at the main offices of Hwaci. Anyoneis free to copy, modify, publish, use, compile, sell, or distribute theoriginal SQLite code, either in source code form or as a compiledbinary, for any purpose, commercial or non-commercial, and by anymeans.The previous paragraph applies to the deliverable code anddocumentation in SQLite - those parts of the SQLite library that youactually bundle and ship with a larger application. Some scripts usedas part of the build process (for example the “configure” scriptsgenerated by autoconf) might fall under other open-source licenses.Nothing from these build scripts ever reaches the final deliverableSQLite library, however, and so the licenses associated with thosescripts should not be a factor in assessing your rights to copy and usethe SQLite library.All of the deliverable code in SQLite has been written from scratch. Nocode has been taken from other projects or from the open internet.Every line of code can be traced back to its original author, and all ofthose authors have public domain dedications on file. So the SQLitecode base is clean and is uncontaminated with licensed code fromother projects.


67

n strlcpy.c , v1.11zCopyright (c) 1998 Todd C. Miller <[email protected]>zPermission to use, copy, modify, and distribute this software for any

purpose with or without fee is hereby granted, provided that theabove copyright notice and this permission notice appear in allcopies.

zTHE SOFTWARE IS PROVIDED “AS IS” AND THE AUTHORDISCLAIMS ALL WARRANTIES WITH REGARD TO THISSOFTWARE INCLUDING ALL IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THEAUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, ORCONSEQUENTIAL DAMAGES OR ANY DAMAGESWHATSOEVER RESULTING FROM LOSS OF USE, DATA ORPROFITS, WHETHER IN AN ACTION OF CONTRACT,NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OFOR IN CONNECTION WITH THE USE OR PERFORMANCE OFTHIS SOFTWARE.

n taglib-1.5copyright : (C) 2002 - 2008 by Scott Wheeleremail : [email protected]“The contents of this file are subject to the Mozilla Public LicenseVersion 1.1 (the “License”); you may not use this file except incompliance with the License. You may obtain a copy of the License athttp://www.mozilla.org/MPL/Software distributed under the License is distributed on an “AS IS”basis, WITHOUT WARRANTY OF ANY KIND, either express orimplied. See the License for the specific language governing rights andlimitations under the License.

n tinyxml 2002.4.3www.sourceforge.net/projects/tinyxmlOriginal file by Yves Berquin.This software is provided 'as-is', without any express or impliedwarranty. In no event will the authors be held liable for any damagesarising from the use of this software.Permission is granted to anyone to use this software for any purpose,including commercial applications, and to alter it and redistribute itfreely, subject to the following restrictions:1. The origin of this software must not be misrepresented; you must

not claim that you wrote the original software. If you use thissoftware in a product, an acknowledgment in the productdocumentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and mustnot be misrepresented as being the original software.

3. This notice may not be removed or altered from any sourcedistribution.


68

n Tremorhttp://wiki.xiph.org/index.php/TremorCopyright (c) 2002, Xiph.org FoundationRedistribution and use in source and binary forms, with or withoutmodification, are permitted provided that the following conditions aremet:1. Redistributions of source code must retain the above copyright



3. Neither the name of the Xiph.org Foundation nor the names of itscontributors may be used to endorse or promote products derivedfrom this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERSAND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIEDWARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALLTHE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANYDIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, ORCONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSSOF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANYWAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISEDOF THE POSSIBILITY OF SUCH DAMAGE.

n zlibhttp://www.zlib.net/zlib.h -- interface of the ‘zlib’ general purpose compression libraryversion 1.2.3, July 18th, 2005Copyright (C) 1995-2004 Jean-loup Gailly and Mark AdlerThis software is provided ‘as-is’, without any express or impliedwarranty. In no event will the authors be held liable for any damagesarising from the use of this software.Permission is granted to anyone to use this software for any purpose,including commercial applications, and to alter it and redistribute itfreely, subject to the following restrictions:1. The origin of this software must not be misrepresented; you must

not claim that you wrote the original software. If you use thissoftware in a product, an acknowledgment in the productdocumentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and mustnot be misrepresented as being the original software.

3. This notice may not be removed or altered from any sourcedistribution.

Jean-loup Gailly [email protected], Mark [email protected]


69

owner’s manualheos 7heos 5 heos 3 - denonowner’s manualheos 7heos 5 heos 3. contents setup use...

Documents