0 - 1Owner’s Manual Model Year 2013.5 Edition: January 2013 TS 1651-B-13VAUXHALL Corsa

Owner’s Manual Model Year 2013.5 Edition: January 2013 TS 1651-B-13

Introduction .................................... 2In brief ............................................ 6Keys, doors and windows ............ 19Seats, restraints ........................... 34Storage ........................................ 51Instruments and controls ............. 68Lighting ........................................ 95Climate control ........................... 103Driving and operating ................. 111Vehicle care ............................... 142Service and maintenance .......... 186Technical data ........................... 190Customer information ................ 219Index .......................................... 222

Contents

2 Introduction

Introduction

Introduction 3

Vehicle specific dataPlease enter your vehicle's data onthe previous page to keep it easilyaccessible. This information isavailable under the sections "Serviceand Maintenance" and "Technicaldata" as well as on the identificationplate.

IntroductionYour vehicle is a designedcombination of advanced technology,safety, environmental friendlinessand economy.This Owner's Manual provides youwith all the necessary information toenable you to drive your vehiclesafely and efficiently.Make sure your passengers areaware of the possible risk of accidentand injury which may result fromimproper use of the vehicle.You must always comply with thespecific laws and regulations of thecountry that you are in. These lawsmay differ from the information in thisOwner's Manual.

When this Owner's Manual refers to aworkshop visit, we recommend yourVauxhall Authorised Repairer. Forgas vehicles, we recommend aVauxhall Authorised Repairerlicensed to service gas vehicles.All Vauxhall Authorised Repairersprovide first-class service atreasonable prices. Experiencedmechanics trained by Vauxhall workaccording to specific Vauxhallinstructions.The customer literature pack shouldalways be kept ready to hand in thevehicle.

Using this manual■ This manual describes all options

and features available for thismodel. Certain descriptions,including those for display andmenu functions, may not apply toyour vehicle due to model variant,country specifications, specialequipment or accessories.

■ The "In brief" section will give youan initial overview.

■ The table of contents at thebeginning of this manual and withineach section shows where theinformation is located.

■ The index will enable you to searchfor specific information.

■ This Owner's Manual depicts left-hand drive vehicles. Operation issimilar for right-hand drive vehicles.

■ The Owner's Manual uses thefactory engine designations. Thecorresponding sales designationscan be found in the section"Technical data".

■ Directional data, e.g. left or right, orfront or back, always relate to thedirection of travel.

■ The vehicle display screens maynot support your specific language.

■ In this manual all display messagesand interior labellings are written inbold type.

4 Introduction

Danger, Warnings andCautions

9 Danger

Text marked 9 Danger providesinformation on risk of fatal injury.Disregarding this information mayendanger life.

9 Warning

Text marked 9 Warning providesinformation on risk of accident orinjury. Disregarding thisinformation may lead to injury.

Caution

Text marked Caution providesinformation on possible damage tothe vehicle. Disregarding thisinformation may lead to vehicledamage.

SymbolsPage references are indicated with 3.3 means "see page".Thank you for choosing a Vauxhall.We wish you many hours ofpleasurable driving.Your Vauxhall Team

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Turn the key in the driver's door lockto the front or press button q tounlock the doors and loadcompartment. Open the doors bypulling the handles. To open thetailgate, pull the button under thetailgate moulding.Radio remote control 3 20, Centrallocking system 3 21, Loadcompartment 3 24.

Seat adjustmentSeat positioning

Pull handle, slide seat, releasehandle.Seat adjustment 3 36, Seat position3 35.

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

In brief 7

Seat backrests

Turn handwheel. Do not lean on seatwhen adjusting.Seat adjustment 3 36, Seat position3 35, Folding front passenger seatbackrest 3 37.

Seat height

Lever pumping motionup = higherdown = lower

Seats 3 36, Seat position 3 35.

Head restraint adjustment

Press release button, adjust height,engage.Head restraints 3 34.

8 In brief

Seat belt

Pull out the seat belt and engage inbelt buckle. The seat belt must not betwisted and must fit close against thebody. The backrest must not be tiltedback too far (maximum approx. 25 °).To release belt, press red button onbelt buckle.Seat belts 3 38, Airbag system3 41, Seat position 3 35.

Mirror adjustmentInterior mirror

Swivel the lever on the underside toreduce dazzle.Interior mirror 3 29, Automatic anti-dazzle interior mirror 3 29.

Exterior mirrors

Setting with four-way switch invehicles with manual windowoperation

First select the relevant exterior mirrorthen use the control to adjust.

In brief 9

Setting with four-way switch invehicles with electronic windowoperation

First select the relevant exterior mirrorthen use the control to adjust.Electric adjustment 3 27, Convexexterior mirrors 3 27, Foldingexterior mirrors 3 27, Heatedexterior mirrors 3 28.

Steering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked. Do not adjust steeringwheel unless vehicle is stationary andsteering wheel lock has beenreleased.Airbag system 3 41, Ignitionpositions 3 112.

10 In brief

Instrument panel overview

In brief 11

1 Side air vents ...................... 1092 Light switch .......................... 95

Instrument illumination ....... 100

Rear fog light ......................... 99

Front fog lights ..................... 99

Headlight rangeadjustment ........................... 96

3 Turn and lane-changesignals, headlight flash,low beam and high beam ..... 98

Exit lighting .......................... 102

Parking lights ........................ 99

Cruise control ....................... 834 Steering wheel controls ........ 685 Horn ...................................... 69

Driver airbag ......................... 416 Instruments .......................... 747 Windscreen wiper,

windscreen washer system ... 70

Trip computer ........................ 898 Centre air vents ................... 109

9 Info-Display ........................... 84

Trip computer ........................ 89

Electronic climate controlsystem ................................. 105

10 Left heated seat .................... 38

Heated steering wheel .......... 69

Tyre deflation detectionsystem ................................. 170

Parking assist ...................... 129

Hazard warning flashers ....... 98

Central locking system .......... 21

Electronic stability program . 127

Airbag deactivation ............... 43

Right heated seat .................. 38

Eco button ........................... 113

Fuel selector ........................ 7511 Front passenger airbag ......... 4112 Glovebox .............................. 5113 Climate control system ........ 103

14 Cigarette lighter ..................... 73

Power outlet .......................... 7315 Ashtray .................................. 7316 Ignition switch with

steering wheel lock ............. 11217 Accelerator pedal ................ 11118 Brake pedal ......................... 12519 Clutch pedal ........................ 11120 Steering wheel adjustment . . . 6821 Bonnet release lever ........... 144

12 In brief

Exterior lighting

Turn light switchAUTO = Automatic light control:

Exterior lighting isswitched on and offautomatically

m = Activation or deactivationof the automatic lightcontrol

8 = sidelights9 = low beam

Press switch> = Front fog lightsr = Rear fog light

Lighting 3 95. Headlight flash, high beam andlow beam

headlight flash = pull leverhigh beam = push leverlow beam = push or pull lever

High beam 3 96, Headlight flash3 96, Automatic light control3 95.

In brief 13

Turn and lane-change signals

right = lever upleft = lever down

Turn and lane-change signals3 98, Parking lights 3 99.

Hazard warning flashers

Operated with the ¨ button.Hazard warning flashers 3 98.

Horn

Press j.

14 In brief

Washer and wiper systemsWindscreen wiper

& = fast% = slow$ = timed interval wipe or

automatic wiping with rainsensor

§ = off

For a single wipe when thewindscreen wiper is off, press thelever down.Windscreen wiper 3 70, Wiperblade replacement 3 149.

Windscreen and headlightwasher systems

Pull lever.Windscreen and headlight washersystem 3 70, Washer fluid 3 146.

Rear window wiper and washersystem

Wiper on = push leverWiper off = push lever againWash = push lever and hold

Rear window wiper and washersystem 3 71, Wiper bladereplacement 3 149, Washer fluid3 146.

In brief 15

Climate controlHeated rear window, heatedexterior mirrors

Heating is operated by pressing theÜ button.Heated rear window 3 31.

Demisting and defrosting thewindows

Air distribution to l.Set temperature control to warmestlevel.Set fan speed to highest level.Cooling n on.Press button V.Climate control system 3 103.

TransmissionManual transmission

Reverse: with the vehicle stationary,wait 3 seconds after depressingclutch pedal and then press therelease button on the selector leverand engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Manual transmission 3 120.

16 In brief

Manual transmission automated

N = neutral positiono = drive position+ = higher gear- = lower gearA = switch between automatic and

manual modeR = reverse gear (with selector

lever lock)

Manual transmission automated3 121.

Automatic transmission

P = park positionR = reverse gearN = neutral positionD = drive position

The selector lever can only be movedout of P or N when the ignition is onand the foot brake is depressed(selector lever lock). To engage P orR, press the release button on theselector lever.The automatic transmission isavailable in two versions 3 117.

Starting offCheck before starting off■ Tyre pressure and condition 3 169,

3 212.■ Engine oil level and fluid levels

3 145.■ All windows, mirrors, exterior

lighting and number plates are freefrom dirt, snow and ice and areoperational.

■ Proper position of mirrors, seats,and seat belts 3 27, 3 35,3 39.

■ Brake function at low speed,particularly if the brakes are wet.

In brief 17

Starting the engine

■ Turn key to position 1■ move the steering wheel slightly to

release the steering wheel lock■ operate clutch and brake. If the

clutch pedal is not operated, theengine might not start and thecontrol indicator - may illuminate

■ automatic transmission in P or N■ do not operate accelerator pedal

■ diesel engines, turn the key toposition 2 for preheating and waituntil control indicator !extinguishes

■ turn key to position 3 and releaseStarting the engine 3 112.

Stop-start system

If the vehicle is at a low speed or at astandstill and certain conditions arefulfilled, activate an Autostop asfollows:■ Depress the clutch pedal■ shift the selector lever to neutral■ release the clutch pedalAn Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.To restart the engine, depress theclutch pedal again.Stop-start system 3 113.

18 In brief

Parking■ Always apply the parking brake

without pressing the release button.Apply as firmly as possible on adownhill slope or uphill slope.Depress the foot brake at the sametime to reduce operating force.

■ Switch off the engine. Turn theignition key to position 0 andremove it. Turn the steering wheeluntil the steering wheel lock is feltto engage.For vehicles with automatictransmission, the key can only beremoved when the selector lever isin the P position.

■ If the vehicle is on a level surface oruphill slope, engage first gear or setthe selector lever to P beforeswitching off the ignition. On anuphill slope, turn the front wheelsaway from the kerb.If the vehicle is on a downhill slope,engage reverse gear or set theselector lever to P before switchingoff the ignition. Turn the frontwheels towards the kerb.

■ Lock the vehicle with button p onthe radio remote control.

■ Activate the anti-theft alarm system3 25.

■ Do not park the vehicle on an easilyignitable surface. The hightemperature of the exhaust systemcould ignite the surface.

■ Close windows and sunroof.■ The engine cooling fans may run

after the engine has been switchedoff 3 143.

■ After running at high engine speedsor with high engine loads, operatethe engine briefly at a low load orrun in neutral for approx.30 seconds before switching off, inorder to protect the turbocharger.

Keys, locks 3 19.Laying the vehicle up for a long periodof time 3 142.

Keys, doors and windows 19

Keys, doors andwindows

Keys, locks ................................... 19Doors ........................................... 24Vehicle security ............................ 25Exterior mirrors ............................ 27Interior mirrors ............................. 29Windows ...................................... 29Roof ............................................. 32

Keys, locksKeysReplacement keysThe key number is specified in theCar Pass or on a detachable tag.The key number must be quotedwhen ordering replacement keys as itis a component of the immobilisersystem.Locks 3 182.

Lock cylindersDesigned to free-wheel if they areforcefully rotated without the correctkey or if the correct key is not fullyinserted. To reset, turn cylinder withthe correct key until its slot is vertical,remove key and then re-insert it. If thecylinder still free-wheels, turn the keythrough 180° and repeat operation.

Key with foldaway key section

Press button to extend. To fold thekey, first press the button.

Car PassThe Car Pass contains securityrelated vehicle data and shouldtherefore be kept in a safe place.When the vehicle is taken to aworkshop, this data is needed in orderto perform certain operations.

20 Keys, doors and windows

Radio remote control

Used to operate:■ Central locking system,■ Anti-theft locking system,■ Anti-theft alarm system,■ Power windows.The radio remote control has a rangeof approx. 5 metres. This range canbe affected by outside influences.The hazard warning flashers confirmoperation.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.

FaultIf the central locking system cannotbe operated with the radio remotecontrol, it may be due to the following:■ Range exceeded,■ Battery voltage too low,■ Frequent, repeated operation of the

radio remote control while not inrange, which will require re-synchronisation,

■ Overload of the central lockingsystem by operating at frequentintervals, the power supply isinterrupted for a short time,

■ Interference from higher-powerradio waves from other sources.

Unlocking 3 21.

Radio remote control batteryreplacementReplace the battery as soon as therange is noticeably diminished.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.

Key with foldaway key section

Keys, doors and windows 21

Extend the key and open the unit.Replace the battery (battery typeCR 2032), paying attention to theinstallation position. Close the unitand synchronise.

Key with fixed key sectionHave the battery replaced by aworkshop.

Radio remote controlsynchronisationAfter replacing the battery, unlock thedoor with the key in the driver's doorlock. The radio remote control will besynchronised when you switch on theignition.

Memorised settingsWhenever the vehicle is locked, thefollowing settings are automaticallymemorised by the key being used:■ Electronic climate control,■ Info-Display,■ Infotainment system,■ Instrument panel illumination.

The saved settings are automaticallyused the next time that key is used tounlock the vehicle.

Central locking systemUnlocks and locks doors, loadcompartment and fuel filler flap.A pull on an interior door handleunlocks the entire vehicle and opensthe door.NoteIn the event of an accident of acertain severity, the vehicle unlocksautomatically.NoteA short time after unlocking with theremote control the doors are lockedautomatically if no door has beenopened.

Unlocking

Central locking system with keyactivation

Turn the key in the driver's door lockto the front.

22 Keys, doors and windows

Central locking system with radioremote control

Press button q.Two settings are possible:■ To unlock only the driver's door:

Press button q once. To unlock theentire vehicle: Press button qtwice.

■ To unlock the entire vehicle: Pressbutton q once.

Settings can be changed in the DriverInformation Centre.Vehicle personalisation 3 93.

LockingClose doors, load compartment andfuel filler flap. If the driver's door is notclosed properly, the central lockingsystem will not work.

Central locking system with keyactivation

Turn the key in the driver's door lockrearwards.

Central locking system with radioremote control

Press button p.

Keys, doors and windows 23

Central locking button

Press button m: the doors are lockedor unlocked.The LED in the button m illuminatesfor approx. 2 minutes after lockingwith the radio remote control.If the doors are locked from the insidewhilst driving, the LED remainsilluminated.

Fault in radio remote control

Unlocking

Turn the key in the driver's door lockas far as it will go. The entire vehicleis unlocked when the driver's door isopened. To unlock the other doors,switch on the ignition and press thecentral locking button.

LockingClose the driver's door, open thepassenger door, then press centrallocking button m. The vehicle islocked. Close the passenger door.

Fault in central locking system

UnlockingTurn the key in the driver's door lockas far as it will go. The other doors canbe opened by pulling the interiorhandle (not possible if the anti-theftlocking system is active). The loadcompartment and fuel filler flapremain locked. To deactivate the anti-theft locking system, switch on theignition 3 25.

Locking

24 Keys, doors and windows

Insert the key into the opening abovethe lock on the inside of the door andoperate the lock by lifting until it clicks.Then close the door. The proceduremust be carried out for each door. Thedriver's door can also be locked fromthe outside with the key. The fuel fillerflap and tailgate cannot be locked.

Automatic lockingThis security feature can beconfigured to automatically lock alldoors, load compartment and fuelfiller flap as soon as the vehicle isdriven. Vehicle personalisation3 93.

Child locks

9 Warning

Use the child locks wheneverchildren are occupying the rearseats.

Using a key or suitable screwdriver,turn button on rear door lock to thehorizontal position. The door cannotbe opened from inside.

DoorsLoad compartmentOpening

Pull the button underneath themoulding.

9 Warning

Do not drive with the tailgate openor ajar, e.g. when transportingbulky objects, as toxic exhaustgases could enter the vehicle.

Keys, doors and windows 25

NoteThe installation of certain heavyaccessories onto the tailgate mayaffect its ability to remain open.

Closing

Use the interior handle.Do not press the button under themoulding while closing as this willunlock the tailgate again.

Vehicle securityAnti-theft locking system

9 Warning

Do not use the system if there arepeople in the vehicle! The doorscannot be unlocked from theinside.

The system deadlocks all the doors.All doors must be closed or thesystem cannot be activated.If the ignition was on, the driver's doormust be opened and closed once sothat the vehicle can be secured.Unlocking the vehicle disables themechanical anti-theft locking system.This is not possible with the centrallocking button.

Activating with the remotecontrol

Press button p again within10 seconds of locking.

Anti-theft alarm systemThe anti-theft alarm system isoperated in conjunction with thecentral locking system.It monitors:■ Doors, load compartment, bonnet,■ Ignition.Unlocking the vehicle deactivates theanti-theft alarm system.

26 Keys, doors and windows

Light-emitting diode (LED)

During the first 10 seconds of anti-theft alarm system activation:LEDilluminates

= Test, ignition delay,

LEDflashesquickly

= Door, loadcompartment orbonnet open, orsystem fault.

After the first 10 seconds of anti-theftalarm system activation:LED flashesslowly

= System active.

Seek the assistance of a workshop inthe event of faults.

AlarmWhen triggered, the alarm gives offan acoustic signal (horn) and a visualsignal (hazard warning flashers). Thenumber and duration of which arestipulated by legislation.The alarm siren can be silenced bypressing any button of the radioremote control or by switching on theignition. The anti-theft alarm system isdeactivated at the same time.If the vehicle's battery is to bedisconnected (e.g. for maintenancework), the alarm siren must bedeactivated as follows: switch theignition on then off, then disconnectthe vehicle's battery within15 seconds.

ImmobiliserThe system checks whether thevehicle is allowed to start with the keybeing used. If the transponder in thekey is recognised, the engine can bestarted.

The immobiliser activates itselfautomatically after the key has beenremoved from the ignition switch.If control indicator A flashes whenthe ignition is on, there is a fault in thesystem; the engine cannot be started.Switch off the ignition and then repeatthe start attempt.If control indicator A continuesflashing, attempt to start the engineusing the spare key and seek theassistance of a workshop.If control indicator A illuminates afterthe engine has started, there is a faultin the engine electronics ortransmission electronics 3 79,3 119, 3 124, or there is water in thediesel fuel filter 3 88.NoteThe immobiliser does not lock thedoors. You should always lock thevehicle after leaving it and switch onthe anti-theft alarm system 3 21,3 25.

Keys, doors and windows 27

Exterior mirrorsConvex shapeThe convex exterior mirror containsan aspherical area and reduces blindspots. The shape of the mirror makesobjects appear smaller, which willaffect the ability to estimatedistances.

Electric adjustmentSetting with four-way switch invehicles with manual windowoperation

First select the relevant exterior mirrorthen use the control to adjust.

Setting with four-way switch invehicles with electronic windowoperation

First select the relevant exterior mirrorthen use the control to adjust.

Folding

For pedestrian safety, the exteriormirrors will swing out of their normalmounting position if they are struckwith sufficient force. Reposition themirror by applying slight pressure tothe mirror housing.

28 Keys, doors and windows

Corsa VXR: For pedestrians safety,the exterior mirrors of the Corsa VXRare released from the holder if theyare struck with sufficient force. Fitmirror housing to holder with latchinglugs and engage by striking gently.

Manual

The exterior mirrors can be folded inby pressing gently on the outer edgeof the housing.

Heated mirrors

Operated by pressing the Ü button.Heating works with the enginerunning. It is switched offautomatically after a short time.

Keys, doors and windows 29

Interior mirrorsManual anti-dazzle

To reduce dazzle, adjust the lever onthe underside of the mirror housing.

Automatic anti-dazzle

Dazzle from following vehicles atnight is automatically reduced.

WindowsWindscreenHeat-reflecting windscreenThe heat-reflecting windscreen has acoating which reflects solar radiation.Also data signals, e.g. from tollstations, might be reflected.

The marked areas on the windscreenare not covered with the coating.Devices for electronic data recordingand fee payment must be attached inthese areas. Otherwise datarecording malfunctions may occur.

30 Keys, doors and windows

Windscreen stickersDo not attach stickers such as tollroad stickers or similar on thewindscreen in the area of the interiormirror. Otherwise the detection zoneof the sensor and the view area of thecamera in the mirror housing could berestricted.

Manual windows

The door windows can be opened orclosed with the window winders.

Power windows

9 Warning

Take care when operating thepower windows. Risk of injury,particularly to children.Keep a close watch on thewindows when closing them.Ensure that nothing becomestrapped in them as they move.

Power windows can be operated:■ with the ignition on,■ within 5 minutes of switching the

ignition off,■ within 5 minutes of turning the

ignition key to position 1.After switching off the ignition, thewindow operation is disabled whenthe driver's door is opened, thenclosed and locked.

Operate the control to open or closethe window.For vehicles with automatic feature,pull or press the switch again to stopwindow movement.

Safety functionIf the window glass encountersresistance during automatic closing, itis immediately stopped and openedagain.In the event of closing difficulties dueto frost or the like, operate the switchseveral times to close the window instages.

Keys, doors and windows 31

Operating windows from outsideDepending on the equipment level,the windows can be operatedremotely from outside the vehicle.

Press q or p until all windows haveopened or closed.

OverloadIf the windows are repeatedlyoperated at short intervals, thewindow operation is disabled forsome time.

FaultIf the windows cannot be opened orclosed automatically, activate thewindow electronics as follows:1. Close doors.2. Switch on ignition.3. Close the window completely and

operate the button for5 more seconds.

4. Open the window completely andoperate the button for1 more second.

5. Repeat this for each window.

Heated rear window

Operated by pressing the Ü button.Heating functions with the enginerunning and is switched offautomatically after a short time.Depending on the engine type, theheated rear window comes onautomatically when the diesel particlefilter is being cleaned.

Sun visorsThe sun visors can be folded down orswivelled to the side to preventdazzling.

32 Keys, doors and windows

If the sun visors have integral mirrors,the mirror covers should be closedwhen driving.

RoofSunroof

9 Warning

Take care when operating thesunroof. Risk of injury, particularlyto children.Keep a close watch on themovable parts when operatingthem. Ensure that nothingbecomes trapped in them as theymove.

Sunroof can be operated with ignitionon.

Operated via a rocker switch in theroof console.Press the button briefly for activationin steps. Hold down the button forlonger for automatic opening.

RaiseWith the sunroof closed, press ü.The sunroof is raised at the rear.

OpenPress ü again with the sunroof in theraised position. The sunroof opensautomatically until it reaches its endposition.To close: press d.

Keys, doors and windows 33

Caution

When using a roof rack, check thefree movement of the sunroof inorder to avoid damage. It is onlypermitted to raise the sunroof.

NoteIf the top of the roof is wet, tiltsunroof, allow water to run off andthen open sunroof.

Do not affix any stickers to sunroof.

CloseHold down d until the sunroof iscompletely closed.

SunblindThe sunblind is manually operated.Close or open the sunblind by sliding.When the sunroof is open, thesunblind is always open.

OverloadIf the system is overloaded, the powersupply is automatically cut-off for ashort time. The system is protected byfuses in the fuse box 3 163.

Initialising the sun roofIf the sunroof cannot be operated,activate the electronics as follows:with ignition on, close the sunroof andhold d depressed for at least10 seconds.Seek the assistance of a workshop tohave the cause of the fault remedied.

34 Seats, restraints

Seats, restraints

Head restraints ............................ 34Front seats ................................... 35Seat belts ..................................... 38Airbag system .............................. 41Child restraints ............................. 45

Head restraints

Position

9 Warning

Only drive with the head restraintset to the proper position.

The upper edge of the head restraintshould be at upper head level. If thisis not possible for extremely tallpeople, set to highest position, andset to lowest position for small people.

Adjustment

Head restraints on front seats

Press release button, adjust height,engage.

Seats, restraints 35

Head restraints on rear seats

The height of the head restraints canbe set in two positions.To set to the first position, pull thehead restraint upwards. To set to thesecond position press the springmarked in the illustration and push thehead restraint right up to the top.To adjust downwards, press thespring marked in the illustration andpush the head restraint downwards.

Active head restraintsIn the event of a rear-end impact, theactive head restraints tilt slightlyforwards. The head is moreeffectively supported so the risk ofwhiplash injury is reduced.NoteApproved accessories may only beattached to the front passenger seathead restraint if the seat is not in use.

Front seatsSeat position

9 Warning

Only drive with the seat correctlyadjusted.

■ Sit with buttocks as far back againstthe backrest as possible. Adjust thedistance between the seat and thepedals so that legs are slightlyangled when pressing the pedals.Slide the front passenger seat asfar back as possible.

36 Seats, restraints

■ Sit with shoulders as far backagainst the backrest as possible.Set the backrest to an angle so thatit is possible to reach the steeringwheel with arms slightly bent.Maintain contact betweenshoulders and the backrest whenturning the steering wheel. Do nottilt the backrest too far back. Werecommend a maximum angle ofapprox. 25°.

■ Adjust the steering wheel 3 68.■ Set the seat high enough to have a

clear field of vision on all sides andon all display instruments. Thereshould be at least one hand ofclearance between head and theroof frame. Thighs should restlightly on the seat without pressinginto it.

■ Adjust the head restraint 3 34.■ Adjust the height of the seat belt

3 39.

Seat adjustment

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

Seat positioning

Pull handle, slide seat, releasehandle.

Seat backrests

Turn handwheel. Do not lean onbackrest when adjusting.

Seats, restraints 37

Seat height

Lever pumping motionup = higherdown = lower

Seat folding

Lift release lever and tilt backrestforwards. Lower release lever andbackrest engages in lowered position.Slide seat forwards.To return backrest to its originalupright position: Lift the release lever,move the backrest back to upright,lower lever, backrest engages.Folding the backrest forwards ispossible only when the backrest is inan upright position.Do not operate handwheel to adjustbackrest with backrest tilted forward.

Corsa VXR

Remove seat belt from belt mount onbackrest.Pull release lever on rear of backrest,tilt backrest forwards and releaselever. Slide seat forwards.To move the backrest upright, slideseat back, pull release lever andmove backrest upright. Releaselever, backrest engages.Folding the backrest forwards ispossible only when the backrest is inan upright position.Do not operate handwheel to adjustbackrest with backrest tilted forward.

38 Seats, restraints

Heating

Activate heating by pressing ß buttonfor the seat with the ignition on.LED in button ß on: relevant frontseat heating on.Seat heating is operational when theengine is running and during anAutostop.

Seat belts

The belts are locked during heavyacceleration or deceleration of thevehicle for the safety of theoccupants.

9 Warning

Fasten seat belt before each trip.In the event of an accident, peoplenot wearing seat belts endangertheir fellow occupants andthemselves.

Seat belts are designed to be used byonly one person at a time. Childrestraint system 3 45.Periodically check all parts of the beltsystem for damage, pollution andproper functionality.Have damaged componentsreplaced. After an accident, have thebelts and triggered belt tensionersreplaced by a workshop.NoteMake sure that the belts are notdamaged by shoes or sharp-edgedobjects or trapped. Prevent dirt fromgetting into the belt retractors.

Seat belt reminder X 3 78.

Belt force limitersIn the front seats, stress on the bodyis reduced by the gradual release ofthe belt during a collision.

Seats, restraints 39

Belt tensioners

In the event of a head-on or rear-endcollision of a certain severity, the frontseat belts are tightened.

9 Warning

Incorrect handling (e.g. removal orfitting of belts) can trigger the belttensioners with risk of injury.

Deployment of the belt tensioners isindicated by illumination of controlindicator v 3 78.

Triggered belt tensioners must bereplaced by a workshop. Belttensioners can only be triggeredonce.NoteDo not affix or install accessories orother objects that may interfere withthe operation of the belt tensioners.Do not make any modifications tobelt tensioner components as thiswill invalidate the vehicle typeapproval.

Three-point seat beltFastening seat belt

Withdraw belt from retractor, guide ituntwisted across the body and insertthe latch plate in the buckle. Tensionthe lap belt regularly whilst driving bytugging the shoulder belt.With the Corsa VXR: Feed seat beltthrough belt mount on backrest whenfastening seat belt.

Loose or bulky clothing prevents thebelt from fitting snugly. Do not placeobjects such as handbags or mobilephones between the belt and yourbody.

40 Seats, restraints

9 Warning

The belt must not rest against hardor fragile objects in the pockets ofyour clothing.

Height adjustment

1. Pull belt out slightly.2. Press button.3. Adjust height and engage audibly.

Adjust the height so that the belt liesacross the shoulder. It must not lieacross the throat or upper arm.Do not adjust while driving.

Removing seat belt

To release belt, press red button onbelt buckle.

Seat belts on the rear outerseatsWhen not in use or to fold forward therear backrests, feed seat beltsthrough belt mount.

Using the seat belt whilepregnant

9 Warning

The lap belt must be positioned aslow as possible across the pelvisto prevent pressure on theabdomen.

Seats, restraints 41

Airbag systemThe airbag system consists of anumber of individual systems.When triggered the airbags inflatewithin milliseconds. They also deflateso quickly that it is often unnoticeableduring the collision.

9 Warning

If handled improperly the airbagsystems can be triggered in anexplosive manner.

NoteThe airbag systems and beltpretensioner control electronics arelocated in the centre console area.Do not put any magnetic objects inthis area.Do not stick anything on the airbagcovers and do not cover them withother materials.Each airbag is triggered only once.Have deployed airbags replaced bya workshop. Furthermore, it might benecessary to have the steering

wheel, the instrument panel, parts ofthe panelling, the door seals,handles and the seats replaced.Do not make any modifications tothe airbag system as this willinvalidate the vehicle type approval.

When the airbags inflate, escapinghot gases may cause burns.Control indicator v for airbag systems3 78.

Front airbag system

The front airbag system consists ofone airbag in the steering wheel andone in the instrument panel on thefront passenger side. These can beidentified by the word AIRBAG.

Additionally there is a warning labelon the side of the instrument panel,visible when the front passenger dooris open, or on the passenger sunvisor.The front airbag system is triggered inthe event of an accident of a certainseverity. The ignition must be on.

42 Seats, restraints

The forward movement of the frontseat occupants is decelerated,thereby considerably reducing therisk of injury to the upper body andhead.

9 Warning

Optimum protection is onlyprovided when the seat is in theproper position.Seat position 3 35.Keep the area in which the airbaginflates clear of obstructions.

Fit the seat belt correctly andengage securely. Only then is theairbag able to protect.

Side airbag system

The side airbag system consists of anairbag in each front seat backrest.This can be identified by the wordAIRBAG.The side airbag system is triggered inthe event of an accident of a certainseverity. The ignition must be on.

The risk of injury to the upper bodyand pelvis in the event of a side-oncollision is considerably reduced.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.

NoteOnly use protective seat covers thathave been approved for the vehicle.Be careful not to cover the airbags.

Seats, restraints 43

Curtain airbag system

The curtain airbag system consists ofan airbag in the roof frame on eachside. This can be identified by theword AIRBAG on the roof pillars.The curtain airbag system is triggeredin the event of an accident of a certainseverity. The ignition must be on.

The risk of injury to the head in theevent of a side impact is considerablyreduced.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.The hooks on the handles in theroof frame are only suitable forhanging up light articles ofclothing, without coat hangers. Donot keep any items in theseclothes.

Airbag deactivationFront airbag and side airbag systemsfor the front passenger seat must bedeactivated if a child restraint systemis to be fitted on this seat. The curtainairbag system, the belt tensionersand all driver airbag systems willremain active.

There is a warning label on the sideof the instrument panel, visible whenthe front passenger door is open.

44 Seats, restraints

Control indicator W and LEDs in thebutton not on:Airbag systems for the frontpassenger are active. No childrestraint systems can be installed.Control indicator W and LEDs inbutton on:Front passenger airbags aredeactivated and will not inflate in theevent of a collision. A child restraintsystem according to the chart Childrestraint installation locations can beinstalled 3 47.

9 Danger

Risk of fatal injury for a child usinga child restraint system on a seatwith activated front passengerairbag.Risk of fatal injury for an adultperson on a seat with deactivatedfront passenger airbag.

Deactivation:■ switch on ignition, control indicatorW flashes,

■ press button W within 15 secondsand hold down,

■ after about 2 seconds, you will heara confirmation buzzer. Releasebutton W after another 4 secondsat the latest.

Activation:■ switch on ignition, control indicatorW flashes,

■ press button W within 15 secondsand hold down,

■ after approx. 2 seconds, you willhear a confirmation buzzer.Release button W after another4 seconds at the latest.

The airbag systems for frontpassenger seat will inflate in the eventof a collision only if control indicatorW does not illuminate.Change status only when the vehicleis stopped with the ignition off.Status remains up to the next change.

Seats, restraints 45

Control indicator for airbagdeactivation 3 78.NoteStarting the engine terminateschanging of the setting.The setting can then only bechanged once the ignition has beenswitched off and back on again.

Child restraintsChild restraint systemsWe recommend the Vauxhall childrestraint system which is tailoredspecifically to the vehicle.When a child restraint system is beingused, pay attention to the followingusage and installation instructionsand also those supplied with the childrestraint system.Always comply with local or nationalregulations. In some countries, theuse of child restraint systems isforbidden on certain seats.

9 Warning

When using a child restraintsystem on the front passengerseat, the airbag systems for thefront passenger seat must bedeactivated; if not, the triggering ofthe airbags poses a risk of fatalinjury to the child.

This is especially the case if rear-facing child restraint systems areused on the front passenger seat.

Airbag deactivation 3 43.

Selecting the right systemThe rear seats are the mostconvenient location to fasten a childrestraint system.Children should travel facingrearwards in the vehicle as long aspossible. This makes sure that thechild's backbone, which is still veryweak, is under less strain in the eventof an accident.Suitable are restraint systems thatcomply with ECE 44-03 orECE 44-04. Check local laws andregulations for mandatory use of childrestraint systems.Ensure that the child restraint systemto be installed is compatible with thevehicle type.Ensure that the mounting location ofthe child restraint system within thevehicle is correct.

46 Seats, restraints

Allow children to enter and exit thevehicle only on the side facing awayfrom the traffic.When the child restraint system is notin use, secure the seat with a seat beltor remove it from the vehicle.NoteDo not stick anything on the childrestraint systems and do not coverthem with any other materials.A child restraint system which hasbeen subjected to stress in anaccident must be replaced.

Seats, restraints 47

Child restraint installation locationsPermissible options for fitting a child restraint system

Weight and age classOn front passenger seat

On rear outboard seats On rear centre seatactivated airbag deactivated airbag

Group 0: up to 10 kgor approx. 10 months

X U1 U2 X

Group 0+: up to 13 kgor approx. 2 years

X U1, 2 U2 X

Group I: 9 to 18 kgor approx. 8 months to 4 years

X U1, 2 U2 X

Group II: 15 to 25 kgor approx. 3 to 7 years

X X U X

Group III: 22 to 36 kgor approx. 6 to 12 years

X X U X

1 = Only if front passenger seat airbag systems are deactivated. If the child restraint system is being secured using athree-point seat belt, move seat height adjustment to uppermost position and ensure that vehicle seat belt runsforwards from the upper anchorage point.

2 = Seat available with ISOFIX and Top-tether mounting brackets (Not available on the front passenger seat in the CorsaVXR).

U = Universal suitability in conjunction with three-point seat belt.X = No child restraint system permitted in this weight class.

48 Seats, restraints

Permissible options for fitting an ISOFIX child restraint systemWeight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat

Group 0: up to 10 kg E ISO/R1 IL IL X

Group 0+: up to 13 kg E ISO/R1 IL IL X

D ISO/R2 X X X

C ISO/R3 X X X

Group I: 9 to 18 kg D ISO/R2 X X X

C ISO/R3 X X X

B ISO/F2 IL, IUF IL, IUF X

B1 ISO/F2X IL, IUF IL, IUF X

A ISO/F3 X X X

IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.The ISOFIX restraint system must be approved for the specific vehicle type.

IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this mass group.X = No ISOFIX child restraint system approved in this weight class.

Seats, restraints 49

ISOFIX size class and seat deviceA – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg.B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.B1 – ISO/F2X = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.C – ISO/R3 = Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg.D – ISO/R2 = Rear-facing child restraint system for smaller children in the weight class up to 13 kg.E – ISO/R1 = Rear-facing child restraint system for young children in the weight class up to 13 kg.

U = Universal suitability in conjunction with three-point seat belt.X = No child restraint system permitted in this weight class.

50 Seats, restraints

Isofix child restraintsystems

Fasten vehicle-approved ISOFIXchild restraint systems to themounting brackets.When using ISOFIX mountingbrackets for seat mounting,universally approved child restraintsystems for ISOFIX may be used.ISOFIX mounting brackets areindicated by a label on the backrest.Closely follow the installationinstructions accompanying theISOFIX child restraint system.

Top-tether child restraintsystems

Depending on country-specificequipment, the vehicle might havetwo or three fastening eyes.Fasten Top-tether child restraintsystems to the fastening eyes on theback of the rear seat and to thepassenger seat rail in the rear footwell. The strap must run between thetwo guide rods of the head restraint.

On the pillar trim of the rear roof andon the attachment points are symbolsindicating the attachment eyes onwhich to mount the child restraintsystem.When using Top-tether for seatmounting, universally approved childrestraint systems for Top-tether maybe used.Closely follow the installationinstructions accompanying theTop-tether child restraint system.

Storage 51

Storage

Storage compartments ................ 51Load compartment ....................... 61Roof rack system ......................... 65Loading information ..................... 66

Storage compartments

9 Warning

Do not store heavy or sharpobjects in the storagecompartments. Otherwise, thestorage compartment lid couldopen and vehicle occupants couldbe injured by objects being thrownaround in the event of hardbraking, a sudden change indirection or an accident.

Glovebox

The glovebox features:■ a card holder in cheque card format■ a pen holder■ pocket torch holderThe glovebox should be closed whilstdriving.

Cupholders

A cupholder is located in the front ofthe centre console.In the 3-door passenger vehicle: alsolocated on the side of the rear seat.

52 Storage

Underseat storage

Lift at recessed edge and pull out.Maximum load: 1.5 kg. To close, pushin and engage.

Rear carrier system

The rear carrier system (Flex-Fixsystem) allows bicycles to beattached to a pull-out carrierintegrated into the vehicle floor. Thetransportation of other objects is notpermitted.The maximum load of the rear carriersystem is 40 kg.The maximum loadper bicycle is 20 kg.If not in use, the carrier system can beslid back into the vehicle floor.There must not be any objects on thebicycles that could become looseduring transportation.

Caution

Do not attach bicycles with carbonpedal cranks to bicycle carriers.The bicycles might get damaged.

ExtendingOpen the tailgate.

9 Warning

No persons may remain in theextension zone of the rear carriersystem, risk of injury.

Storage 53

Pull release lever up. The systemdisengages and travels quickly out ofthe bumper.

Completely pull out the rear carriersystem until you hear it engage.Ensure that it is not possible to pushin the rear carrier system withoutpulling the release lever again.

9 Warning

It is only permissible to fit objectsto the rear carrier system if thesystem has been correctlyengaged. If the rear carrier system

will not engage correctly, do not fitobjects to the system and slide thesystem back. Seek the assistanceof a workshop.

Install the tail lamps

First remove the rear (1), then thefront (2) tail lamp from the recesses.

Open out the lamp support on theback of the tail lamp completely untilit engages.

54 Storage

Push the clamping lever down andpush the lamp support into theretainer until it engages.Perform this procedure for both taillamps.

Check the cable and lamp position tomake sure these are correctlyinstalled and are securely located.

Lock the rear carrier system

Swivel the left clamping lever (1) first,followed by the right clamping lever(2) until they stop. Both clampinglevers must point backwards,otherwise safe functionality is notguaranteed.NoteClose the tailgate.

Unfold pedal crank recesses

Fold one or both pedal crankrecesses upwards until the diagonalsupport engages.

Storage 55

Remove the pedal crank mounts fromthe pedal crank recesses.

Adapting the rear carrier systemto a bicycle

Press the release lever and withdrawthe wheel recesses.

Push the release lever on the strapretainer and remove the strapretainer.

56 Storage

Prepare the bicycle forattachment

NoteThe maximum width for the pedalcrank is 38.3 mm and the maximumdepth is 14.4 mm.

Rotate the left pedal (without a chaincog) vertically downwards. The pedalon the left pedal crank must behorizontal.The front bicycle must have its frontwheel facing left.The rear bicycle must have its frontwheel facing right.

Attaching a bicycle to the rearcarrier system

With the rotary lever on the pedalcrank recess, roughly adapt theadjustable pedal crank unit to theprotrusion of the pedal crank.If the bicycle has straight pedalcranks, unscrew the pedal crank unitcompletely (position 5).

If the bicycle has curved pedalcranks, screw in the pedal crank unitall the way (position 1).

Storage 57

Put on the bicycle. The pedal crankhere must be placed in the pedalcrank recess opening as shown in theillustration.

Caution

Make sure that the pedal does nottouch the surface of the rear endcarrier. Otherwise the cranksetmight be damaged during thetransport.

Insert pedal crank mount into outerrail of each pedal crank recess fromabove and slide downwards until atleast underneath the notching.

Attach the pedal crank by rotating theattachment screw on the pedal crankmount.

Place the wheel recesses so that thebicycle is roughly horizontal. Here,the distance between the pedals andthe tailgate should be at least 5 cm.Both bicycle tyres must be in thewheel recesses.

Align the bicycle in the longitudinaldirection of the vehicle: Slightlyloosen the pedal mount.Place the bicycle upright using therotary lever on the pedal crankrecess.If the two bicycles obstruct oneanother, the relative positions of thebicycles can be adapted by adjusting

58 Storage

the wheel recesses and the rotarylever on the pedal crank recess untilthe bicycles no longer touch oneanother. Make sure there is sufficientclearance from the vehicle.

Tighten the attachment screw for thepedal bearing mount to its maximumpoint by hand.Secure both bicycle wheels to wheelrecesses using strap retainers.Check the bicycle to make sure it issecure.

Caution

Ensure gap between bicycle andvehicle is at least 5 cm. Ifnecessary, loosen handlebar andswivel sideways.

The settings for the wheel recessesand on the rotary lever on the pedalcrank recess should be noted andsaved for each bicycle. Correctpresetting will facilitate refitting of thebicycle.NoteIt is recommended to attach awarning sign at the rearmost bicycleto increase visibility.

Removing a bicycle from therear carrier system

Undo strap retainers on both bicycletyres.Hold on to the bicycle, loosen theattachment screw for the pedalbearing mount, then lift the pedalbearing mount to remove it.

Storage 59

Retracting the rear carriersystem

Push the pedal crank mounts into thepedal crank recess as shown in theillustration.

Insert the strap retainer and pulltightly downwards as far as possible.

Press release lever and slide in wheelrecesses all the way as far as they willgo.

Disengage the locking lever on thediagonal support and fold both pedalcrank recesses down.

9 Warning

Risk of pinching.

60 Storage

Swivel first the right clamping lever(1) forwards, followed by the leftclamping lever (2), until they can beengaged in their respective recesses.

Push the clamping lever down andpull both lamp supports out of therecesses.

Fold in the lamp supports on thebacks of the tail lamps.First place the front tail lamp (1), thenthe rear tail lamp (2) in the recessesand push down as far as possible.Push cables all the way into all guidesin order to prevent damage.Open the tailgate.

Push the release lever up and hold.Lift the system slightly and push it intothe bumper until it engages.Release lever must return to originalposition.

9 Warning

If the system cannot be correctlyengaged, please seek theassistance of a workshop.

Storage 61

Load compartment

Load compartment extensionThe rear backrest, in a single unit orsplit, can be locked in an uprightposition for transporting bulky items.

Pull the release handle, pull thebackrest forwards to the verticalposition and engage.When unlocking, a red markingappears next to the release lever. Thebackrest is only engaged correctlywhen the red bolt is no longerprotruding.

If the backrest is split, unlock therelevant side, and unlock at bothsides if it is a single unit.

Folding down rear backrestsRemove load compartment cover asnecessary.Push head restraints down bypressing the catch.

Guide the seat belts through sidesupports to protect them againstdamage. When folding the backrests,pull the seat belts along with them.

Disengage the backrest (single orsplit) using the release lever and foldit down onto the seat cushion.If the backrest is split, unlock therelevant side, and unlock at bothsides if it is a single unit.If the vehicle is to be loaded via a reardoor, take the seat belt out of the seatbackrest guide, roll it up and insert thelatch plate into the side shaderetainer.

62 Storage

Move rear seat backrests upright andallow locking mechanisms to engageaudibly at both sides. Once thebackrests are locked the red markmust no longer protrude.The rear seat backrests can belocked in two positions.Do not trap the seat belt when movingthe backrest to the upright position.Install the load compartment cover.

9 Warning

Only drive the vehicle when thebackrests are securely locked intoposition. Otherwise there is a riskof personal injury or damage to theload or vehicle in the event of hardbraking or a collision.

The seat belt of the centre seat couldbe blocked when the backrest isfolded up too quickly. To unlock theretractor, push in the seat belt or pullit out by approx. 20 mm and then letgo.

Load compartment coverDo not place any objects on the cover.

5-door passenger vehicle

Lift the cover backwards, until itunlatches, then remove.Fit in reverse order.

Storage 63

3-door passenger vehicle

Lift the cover backwards until itunlatches, set at an angle, thenremove.Fit in reverse order.

StowingWhen the load compartment is fullyloaded, stow the load compartmentcover behind the rear seat backrests:Lift the cover backwards until itunlatches, then slide down in guidesbehind the seat backrests.

Van

The load compartment cover consistsof four segments which can beindividually removed and inserted.The rear segment (1) has identicalfunctionality (removal andinstallation) to that of the 3-doorpassenger vehicle 3 62.

To remove the three other segments(order 2 to 4) lift at the rear,disengage, twist and remove.Install the segments in the order 4 to1. Engage segments in recesses atthe side.The segments overlap at theconnecting points when they areclosed.

64 Storage

Rear floor storage cover

The double load-bay floor can beinserted in the load compartment intwo positions:■ directly beneath the cover for the

spare wheel recess or the floorcover,

■ or in the upper openings in the loadcompartment.

To remove, lift the load-bay floorusing the lever and pull backwards.To insert, push the load-bay floorforwards in the corresponding guide,then lower.

If mounted in the upper position, thespace between the load-bay floor andthe spare wheel well cover can beused as a stowage compartment.In this position, if the rear seatbackrests are folded forwards, analmost completely flat load bay iscreated.The double load-bay floor is able towithstand a load of no more than100 kg.In models with a tyre repair kit, thespare wheel recess may be used asan additional stowage compartment.

Lashing eyes

The lashing eyes are designed tosecure items against slippage, e.g.using lashing straps or luggage net.

Storage 65

Warning triangle

Store warning triangle in rear loadcompartment wall: first fit warningtriangle into recess on left and theninsert in guide on right.To remove the warning triangle, lift tothe right and pull out to the right.

First aid kit

Stow the first-aid kit (cushion) in thecompartment in the left wall of theload compartment.To open the compartment, disengagecover and open it.

Roof rack systemRoof rackFor safety reasons and to avoiddamage to the roof, the vehicleapproved roof rack system isrecommended.

Follow the installation instructionsand remove the roof rack when not inuse.

Fitting on model without sun roofPush covers for concealing roof rackmounts down and push backwardswith a valve cap key 3 167.

66 Storage

Fitting on model with sun roofDisengage covers concealing roofrack mounts by pushing sliders indirection of arrow (e.g. with coin) andremove upwards. To close roof rackmounts, first insert covers at front andengage sliders at rear.Attach roof rack at appropriate points,see enclosed roof rack systeminstructions.

Loading information

■ Heavy objects in the loadcompartment should be placedagainst the seat backrests. Ensurethe backrests are securelyengaged. If objects can be stacked,the heavier objects should beplaced at the bottom.

■ Secure objects with lashing strapsattached to lashing eyes.

■ Secure loose objects in loadcompartment to prevent sliding.

■ When transporting objects in theload compartment, the backrests ofthe rear seats must not be angledforward.

■ Do not allow the load to protrudeabove the upper edge of thebackrests.

■ Do not place any objects on theload compartment cover or theinstrument panel, and do not coverthe sensor on top of the instrumentpanel.

■ The load must not obstruct theoperation of the pedals, parkingbrake and gear selector, or hinderthe freedom of movement of thedriver. Do not place any unsecuredobjects in the interior.

■ Do not drive with an open loadcompartment.

9 Warning

Always make sure that the load inthe vehicle is securely stowed.Otherwise objects can be thrown

Storage 67

around inside the vehicle andcause personal injury or damageto the load or car.

■ The payload is the differencebetween the permitted grossvehicle weight (see identificationplate 3 190) and the EC kerbweight.To calculate the payload weight,enter the data for your vehicle in theWeights table at the front of thismanual.The EC kerb weight includesweights for the driver (68 kg),luggage (7 kg) and all fluids (tank90 % full).Optional equipment andaccessories increase the kerbweight.

■ Driving with a roof load increasesthe sensitivity of the vehicle tocross-winds and has a detrimentaleffect on vehicle handling due tothe vehicle’s higher centre ofgravity. Distribute the load evenlyand secure it properly with retainingstraps. Adjust the tyre pressure and

vehicle speed according to the loadconditions. Check and retighten thestraps frequently.Do not drive faster than 75 mph.The permissible roof load is 75 kg.The roof load is the combinedweight of the roof rack and the load.

68 Instruments and controls

Instruments andcontrols

Controls ....................................... 68Warning lights, gauges andindicators ..................................... 74Information displays ..................... 83Vehicle messages ........................ 87Trip computer ............................... 89Vehicle personalisation ................ 93

ControlsSteering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked.Do not adjust steering wheel unlessvehicle is stationary and steeringwheel lock has been released.

Steering wheel controls

The Infotainment system and theInfo-Display can be operated via thecontrols on the steering wheel.Further information is available in theInfotainment system manual.

Instruments and controls 69

Heated steering wheel

Activate heating in combination withthe seat heating by pressing ß*button once or several times with theignition on.LED ß on: driver seat heating on.LED ß and * on: driver seat heatingand steering wheel heating on.LED * on: steering wheel heating on.

The steering wheel is heated in theareas shown in the illustration whenthe engine is running and during anAutostop.

Horn

Press j.

70 Instruments and controls

Windscreen wiper/washerWindscreen wiper

The lever always springs back to itsoriginal position.& = fast% = slow$ = interval wiping§ = off

For a single wipe when thewindscreen wiper is off, press thelever down.

Run through the windscreen wiperstages by pushing the lever past theresistance point and holding it. Anacoustic signal sounds at §.Do not use if the windscreen is frozen.Switch off in car washes.

Adjustable wiper intervalTo set the wiper interval to a valuebetween 2 and 15 seconds: Switch onignition, move lever down fromposition §, wait desired time intervaland raise lever to $.After turning on the ignition andsetting the lever to $, the interval isset to 6 seconds.

Automatic wiping with rain sensor

$ = Automatic wiping with rainsensor

The rain sensor detects the amount ofwater on the windscreen andautomatically regulates the frequencyof the windscreen wiper.

Instruments and controls 71

Keep the sensor free from dust, dirtand ice.

Windscreen washer

Pull lever. Washer fluid is sprayedonto the windscreen and the wiperwipes a few times.

Rear window wiper/washer

Push lever forwards. The rear windowwiper wipes in interval mode. Switchoff by pushing lever forwards again.Do not use if the rear window isfrozen.Switch off in car washes.If the lever is held forwards, washerfluid is sprayed onto the rear window.

The rear windscreen wiper comes onautomatically when the windscreenwiper is switched on and reverse gearis engaged. Activation or deactivationof this function can be changed.Vehicle personalisation 3 93.

Outside temperature

A drop in temperature is indicatedimmediately and a rise in temperatureafter a time delay.If the outside temperature drops to3 °C, the symbol : illuminates in theTriple-Info-Display or theBoard-Info-Display as a warning for

72 Instruments and controls

icy road conditions. : remainsilluminated until the temperaturereaches at least 5 °C.

In vehicles with Graphic-Info-Displayor Colour-Info-Display, a warningmessage appears in the display as awarning for icy road conditions. Thereis no message below -5 °C.

9 Warning

The road surface may already beicy even though the displayindicates a few degrees above0 °C.

ClockDate and time are shown in theInfo-Display.Graphic-Info-Display,Colour-Info-Display 3 84.

Set date and time inTriple-Info-Display

The Infotainment system must be off.Activate setting mode by holding theÖ button depressed for approx.2 seconds. The flashing value isadjusted using the ; button. The Öbutton is used to switch to the nextmode and to exit setting mode.

Automatic time synchronisationThe RDS signal of most VHFtransmitters automatically sets thetime, identified by } in the display.Some transmitters do not send acorrect time signal. In such cases, it isrecommend to switch off automatictime synchronisation.Activate setting mode and set it toyear setting. Hold the Ö buttondepressed for approx. 3 secondsuntil } flashes in the display and "RDSTIME" appears. The function isactivated (RDS TIME 1) ordeactivated (RDS TIME 0) withthe ; button. Exit setting mode usingthe Ö button.

Instruments and controls 73

Power outlets

The power outlet is located in thecentre console.

Caution

Do not damage the outlet by usingunsuitable plugs.

Connecting electrical accessorieswhile the engine is off will dischargethe battery. Do not exceed themaximum power consumption of120 Watts. Do not connect any

current-delivering accessories, e.g.electrical charging devices orbatteries.Electrical accessories that areconnected must comply with theelectromagnetic compatibilityrequirements laid down inDIN VDE 40 839.If the tyre repair set is in operation, noconsumers may be connected to theauxiliary outlet.Stop-start system 3 113.

Cigarette lighter

The cigarette lighter is located in thecentre console.Press in cigarette lighter. It switchesoff automatically once the element isglowing. Pull out lighter.

Ashtrays

Caution

To be used only for ash and not forcombustible rubbish.

Portable ashtray

74 Instruments and controls

The portable ashtray can be placed inthe cupholders. Open cover to use. Warning lights, gauges

and indicatorsInstrument clusterIn some versions, the needles of theinstruments briefly rotate to the endposition when the ignition is switchedon.

Speedometer

Indicates vehicle speed.

Speed warningWith the "Personalised key" function,P6 a particular top speed can beassigned to each vehicle key. Whenthis speed is exceeded, a warningbuzzer sounds. Vehiclepersonalisation 3 93.

Odometer

The bottom line displays the recordeddistance.

Instruments and controls 75

Trip odometerThe top line displays the recordeddistance since the last reset.To reset, hold the reset knobdepressed for a few seconds with theignition on.

Tachometer

Displays the engine speed.Drive in a low engine speed range foreach gear as much as possible.Upshift when indicated by the controlindicator [ 3 80.

Caution

If the needle is in the red warningzone, the maximum permittedengine speed is exceeded. Engineat risk.

Fuel gauge

Displays the fuel level or gas level inthe tank depending on the operationmode.Control indicator Y illuminates if thelevel in the tank is low. Refuelimmediately if it flashes.

During liquid gas operation, thesystem automatically switches over topetrol operation when gas tanks areempty 3 75.Never run the tank dry.Because of the fuel remaining in thetank, the top-up quantity may be lessthan the specified tank capacity.

Fuel selector

Pressing button LPG switchesbetween petrol and liquid gasoperation. The LED 1 status showsthe current operating mode.

76 Instruments and controls

1 off = petrol operation1 illuminates = liquid gas

operation1 flashes = no switching is

possible, one typeof fuel is empty

As soon as the liquid gas tanks areempty, petrol operation isautomatically engaged until theignition is switched off.Fuel for liquid gas operation 3 131.

Service display

The message InSP appears when itis time for servicing. Furtherinformation 3 186.

Transmission display

The mode or selected gear is shownin the transmission display.P = Automatic transmission

park positionR = Reverse gearN = Neutral positionA = Manual transmission

automated automatic modeD = Drive position

1, 2,3

= Selected gear, automatictransmission

1 - 5 = Current gear, manualtransmission automated,manual mode

Control indicatorsThe control indicators described arenot present in all vehicles. Thedescription applies to all instrumentversions. When the ignition isswitched on, most control indicatorswill illuminate briefly as a functionalitytest.The control indicator colours mean:red = danger, important

reminderyellow = warning, information, faultgreen = confirmation of activationblue = confirmation of activation

Instruments and controls 77

Control indicators in the instrument

78 Instruments and controls

Turn signalO illuminates or flashes green.

IlluminatesThe control indicator illuminatesbriefly when the parking lights areswitched on.

FlashesThe control indicator flashes if a turnsignal or the hazard warning flashersare activated.Rapid flashing: failure of a turn signallight or associated fuse, failure of turnsignal light on trailer.Bulb replacement 3 150. Fuses3 163. Turn signals 3 98.

Seat belt reminderX illuminates or flashes red.

IlluminatesAfter the ignition is switched on untilthe seat belt is fastened.

FlashesAfter starting off until the seat belt isfastened.Fastening the seat belt 3 39.

Airbag and belt tensionersv illuminates red.When the ignition is switched on, thecontrol indicator illuminates forapprox. 4 seconds. If it does notilluminate, does not go out after4 seconds or illuminates whilstdriving, there is a fault in the belttensioner or the airbags. In this casethe LEDs in the button W will alsoflash. The airbags and belt tensionersmay fail to trigger in the event of anaccident.Deployment of the belt tensioners orairbags is indicated by continuousillumination of v.

9 Warning

Have the cause of the faultremedied immediately by aworkshop.

Airbag system, belt tensioners 3 41,3 38.

Airbag deactivationW illuminates together with the LEDsin the button W: airbag deactivated3 43.W flashes: the system can beactivated or deactivated within15 seconds of switching on theignition 3 43.

Charging systemp illuminates or flashes red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Instruments and controls 79

Illuminates when the engine isrunningStop, switch off engine. Battery is notcharging. Engine cooling may beinterrupted. In diesel engines, powerto the brake servo unit may be cut.Seek the assistance of a workshop.

Flashes during or after enginestartBattery voltage too low. Haveelectrical system tested by aworkshop.

Malfunction indicator lightZ illuminates or flashes yellow.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningFault in the emission control system.The permitted emission limits may beexceeded. Immediately seek theassistance of a workshop.

Flashes when the engine isrunningFault that could lead to catalyticconverter damage. Ease up on theaccelerator until the flashing stops.Seek the assistance of a workshopimmediately.

Service vehicle soonA illuminates or flashes yellow.

Illuminates when the engine isrunningFault in engine or transmissionelectronics. The electronics switch toan emergency running programme.Fuel consumption may be increasedand the vehicle handling may beimpaired.If the fault persists after restarting thevehicle, consult a workshop.

Illuminates together with InSP4in the service displaySeek the assistance of a workshop fordraining the diesel fuel filter.

Flashes with switched onignitionFault in the immobiliser system. Theengine cannot be started 3 26.

Brake and clutch systemBrake and clutch fluid levelR illuminates red.Illuminates when the parking brake isreleased if the brake and clutch fluidlevel is too low 3 147.

9 Warning

Stop. Do not continue yourjourney. Consult a workshop.

Illuminates after the ignition isswitched on if the parking brake isapplied 3 126.

Apply parking brakeR flashes red.

80 Instruments and controls

On vehicles with manual transmissionautomated, R flashes for a fewseconds when the ignition is switchedoff if the parking brake is not applied.On vehicles with manual transmissionautomated, R flashes when thedriver's door is opened if no gear isengaged and the parking brake is notapplied.

Apply clutch pedal- illuminates yellow.Clutch pedal needs to be operated tostart the engine.Stop-start system 3 113.

Antilock brake system(ABS)u illuminates red.Illuminates for a few seconds after theignition is turned on. The system isready for operation when the controlindicator extinguishes.If the control indicator does not go outafter a few seconds, or if it illuminateswhile driving, there is a fault in the

ABS. The brake system remainsoperational but without ABSregulation.Antilock brake system 3 125.

Upshift[ illuminates green when upshiftingis recommended for fuel savingreasons.

Sport mode1 illuminates yellow.The symbol is illuminated when Sportmode is on 3 122.

Winter modeT illuminates yellow.The symbol is illuminated whenWinter mode is on 3 118, 3 122.

Power steeringp illuminates yellow.

Fault in power steering system. Thepower steering may have failed. Thevehicle can be steered butconsiderably more force is required.Contact a workshop.

Ultrasonic parking assistr illuminates or flashes yellow.

IlluminatesFault in system. Have the cause of thefault remedied by a workshop.

FlashesFault due to sensors that are dirty orcovered by ice or snow.orInterference due to external sourcesof ultrasound. Once the source ofinterference is removed, the systemwill operate normally.Ultrasonic parking assist 3 129.

Electronic StabilityProgramv flashes or illuminates yellow.

Instruments and controls 81

Illuminates for a few seconds whenthe ignition is switched on.

Flashing during drivingThe system is actively engaged.Engine output may be reduced andthe vehicle may be brakedautomatically to a small degree3 127.

Illuminates while drivingThe system is switched off or a faultis present. Continued driving ispossible. Driving stability, however,may deteriorate depending on roadsurface conditions.Have the cause of the fault remediedby a workshop.Electronic stability program 3 127.

Engine coolanttemperatureW illuminates red.

Illuminates when the engine isrunningStop, switch off engine.

Caution

Coolant temperature too high.

Check coolant level immediately3 146.If there is sufficient coolant, consult aworkshop.

Preheating and dieselparticle filter! illuminates or flashes yellow.

IlluminatesPreheating activated. Only activateswhen outside temperature is low.

Flashes(in vehicles fitted with a diesel particlefilter).Control indicator ! flashes if the filterrequires cleaning and previousdriving conditions did not permitautomatic cleaning. Continue drivingand if possible do not allow enginespeed to drop below 2000 rpm.

The control indicator ! extinguishesas soon as the self-cleaningoperation is complete.Diesel particle filter 3 115, Stop-startsystem 3 113.

Deflation detection systemw illuminates red or yellow.

Illuminates redDeflation detected. Stop immediatelyand check tyre pressure.

Illuminates yellowFault in system. Consult a workshop.Deflation detection system 3 170.

Engine oil pressureI illuminates red.Illuminates for a few seconds after theignition is switched on.

82 Instruments and controls

Illuminates when the engine isrunning

Caution

Engine lubrication may beinterrupted. This may result indamage to the engine and/orlocking of the drive wheels.

1. Depress clutch.2. Select neutral gear, set selector

lever to N.3. Move out of the flow of traffic as

quickly as possible withoutimpeding other vehicles.

4. Switch off ignition.

9 Warning

When the engine is off (exceptduring an Autostop), considerablymore force is needed to brake andsteer.

Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engageunexpectedly.

Check oil level before seeking theassistance of a workshop 3 145.

Low engine oil levelS illuminates yellow.Engine oil level is checkedautomatically.

Illuminates when the engine isrunningLow engine oil level. Check engine oillevel and top up as necessary3 145.

Low fuelY illuminates or flashes yellow.

IlluminatesLevel in fuel tank too low.

FlashesFuel used up. Refuel immediately.Never run the tank dry.Erratic fuel supply can cause catalyticconverter to overheat 3 116.Bleeding the diesel fuel system3 149.

Apply footbrakej illuminates yellow.With manual transmissionautomated, the engine can only bestarted if the foot brake is depressed.If the foot brake is not depressed, thecontrol indicator illuminates 3 121.

Exterior light8 illuminates green.Illuminated when the exterior lightsare on 3 95.

High beamP illuminates blue.Illuminated when high beam is on andduring headlight flash 3 96.

Instruments and controls 83

Adaptive forward lightingB illuminates yellow.

Illuminates when the engine isrunningFault in system.Seek the assistance of a workshop.

Illuminates after ignition isswitched onControl indicator B illuminates forapprox. 4 seconds as a functionalitytest.Control indicator B illuminates forapprox. 8 seconds as a reminder thatthe headlights have been set tosymmetrical low beam 3 97.

Fog light> illuminates green.Illuminated when the front fog lightsare on 3 99.

Rear fog lightr illuminates yellow.

Illuminated when the rear fog light ison 3 99.

Cruise controlm illuminates or flashes green.

IlluminatesIlluminates when the system is on3 128.

FlashesCruise control was enabled withoutdepressing the brake pedalbeforehand.

Information displaysTriple-Info-Display

Displays time, outside temperatureand date or Infotainment system(when it is on).When the ignition is off, the time, dateand outside temperature can bedisplayed by briefly pressing one ofthe two buttons below the display.

84 Instruments and controls

Graphic-Info-Display,Colour-Info-Display

Displays time, outside temperature,date or Infotainment system (when itis on) and electronic climate controlsystem.The Colour-Info-Display displays theinformation in colour.The type of information and how it isdisplayed depends on the equipmentof the vehicle and the settings made.

Selecting functionsFunctions and settings of theInfotainment system and electronicclimate control system are accessedvia the display.Selections are made via the menusand buttons or the left adjuster wheelof the steering wheel.

Selecting with the Infotainmentsystem buttons

Select menu items via the menus andby using the Infotainment systembuttons. The OK button is used toselect the highlighted item or confirma command.

To exit a menu, press the right or leftarrow button until Return or Mainappear and select.

Selecting with the left adjuster wheelon the steering wheel

Rotate to select a menu item.Press the adjuster wheel to select thehighlighted item or confirm acommand.

Instruments and controls 85

Function areas

For each function area there is a mainpage (Main), which is selected at thetop edge of the display (only with tripcomputer and Mobile Phone Portal):■ Audio,■ Telephone,■ Trip computer.

System settings

Press the Settings button on theInfotainment system. ForInfotainment system CD 30, no menumay be selected.

Setting date and time

Select menu item Time, Date from theSettings menu.Select the required menu items andmake settings.Changing the time setting will alsochange the time setting of thenavigation system.

Automatic time synchronisationThe RDS signal of most VHFtransmitters automatically sets thetime.

86 Instruments and controls

Some transmitters do not send acorrect time signal. In such cases, werecommend to switch off automatictime synchronisation.The function is activated byhighlighting the field in front ofSynchron. clock automatical. in theTime, Date menu.

Language selection

The display language for somefunctions can be selected.Select menu item Language from theSettings menu.Select the desired language.

Selection is indicated by a 6 in frontof the menu item.When the language setting of thedisplay is changed, the system willask whether the announcementlanguage of the Mobile Phone Portalshould also be changed - seeInfotainment system manual.

Setting units of measure

Select menu item Units from theSettings menu.Select the desired unit.Selections are indicated by a o infront of the menu item.

Instruments and controls 87

Adjusting contrast(Graphic-Info-Display)

Select menu item Contrast from theSettings menu.Confirm the required setting.

Setting display modeDisplay brightness is dependent onvehicle lighting. Additional settingscan be made as follows:Select menu item Day / Night from theSettings menu.Automatic The colours are adapted tothe exterior lights.

Always day design black or colouredtext on light background.Always night design white or colouredtext on dark background.Selection is indicated by a o in frontof the menu item.

Ignition logicSee Infotainment system manual.

Smartphone controllerThe smartphone controller allows asmartphone to access vehicle datavia WLAN or Bluetooth connection.This data can then be displayed andanalysed on the smartphone.

Vehicle messagesMessages are given via theinstrument panel display or aswarning and signal buzzers. Checkcontrol messages appear on theInfo-Display. Some appear in anabbreviated form. Confirm warningmessages with the multifunction knob3 84.

Warning chimesWhen starting the engine orwhilst driving■ If seat belt is not fastened.■ If a door or the tailgate is not fully

closed when starting-off.■ If a certain speed is exceeded with

the parking brake applied.■ If the speed programmed at the

factory is exceeded.■ If the vehicle has manual

transmission automated and thedriver's door is opened when the

88 Instruments and controls

engine is running, a gear isengaged and the foot brake is notdepressed.

■ Warning signal sounds three timesif the rear carrier system isextended and reverse gear isselected.

When the vehicle is parked andthe driver's door is opened■ When the key is in the ignition

switch.■ With exterior lights on.■ For manual transmission

automated, if the parking brake isnot applied and no gear is engagedwhen the engine is switched off.

During an Autostop■ If the driver's door is opened.

Battery voltageLow battery voltage in the radioremote control. On vehicles withoutcheck control, the message InSP3appears in the instrument paneldisplay. Replace the battery 3 20.

Brake light switchBrake light does not come on duringbraking. Have the cause of the faultremedied immediately by aworkshop.

Drain diesel fuel filterIf there is water in the diesel fuel filter,the message InSP4 appears in theinstrument panel. In some modelsInSP4 illuminates together with A inthe instrument. Consult a workshop.

LightingImportant exterior lighting lamps,including cables and fuses, aremonitored. In trailer mode, trailerlighting is also monitored. Trailerswith LED lighting must have anadapter that enables lamp monitoringas with conventional bulbs.

The failed lighting will be indicated inthe information display or themessage InSP2 will appear in theinstrument panel display.

Instruments and controls 89

Trip computer

The trip computer providesinformation on driving data, which iscontinually recorded and evaluatedelectronically.

The functions can be selected via thebuttons on the wiper lever.Turn the adjuster wheel to select:■ Range■ Instantaneous consumption■ Distance travelled■ Average speed■ Absolute consumption■ Average consumption■ Stop watch

RangeRange is calculated from current fueltank content and currentconsumption. The display showsaverage values.After refuelling, the range is updatedautomatically after a brief delay.When the fuel level in the tank is low,a message appears on the display.Confirm the warning message bypressing 7 on the wiper lever.

Instantaneous consumptionDisplay of the instantaneousconsumption. At low speeds,consumption per hour is displayed.

Distance travelledDisplay of distance travelled.

Average speedDisplay of average speed. Themeasurement can be reset at anytime.

Absolute consumptionDisplay of fuel consumed.

90 Instruments and controls

Average consumptionDisplay of average consumption. Themeasurement can be reset at anytime.

Stop watchMeasurement of the time fromactivation to deactivation.Press the 7 button to start and stopthe measurement.

Reset trip computerThe measurement or calculation ofthe following trip computerinformation can be restarted:■ Distance,■ Average speed,■ Absolute consumption,■ Average consumption.Select the desired function. To reseta value to zero, hold down the button7 for more than three seconds.To reset all functions, hold down thebutton 7 for more than 6 seconds.

Trip computer in Graphic-Info-Display or Colour-Info-DisplayThe main page of the trip computerprovides information on range,current consumption and averageconsumption of BC 1.To display other trip computer data,press the BC button on theInfotainment system, select the tripcomputer menu from the display orpress the left adjuster wheel on thesteering wheel.Select BC 1 or BC 2 from the tripcomputer menu.

Range

Range is calculated from current fueltank content and currentconsumption. The display showsaverage values.After refuelling, the range is updatedautomatically after a brief delay.

Instruments and controls 91

When the fuel level in the tank is low,the message Range appears in thedisplay.When the fuel tank is nearly empty,the message Please refuel! appearsin the display.

Instantaneous consumptionDisplays the instantaneousconsumption. At low speeds,consumption per hour is displayed.

DistanceDisplay of distance travelled. Themeasurement can be reset at anytime.

Average speedDisplay of average speed. Themeasurement can be reset at anytime.Stoppages in the journey with theignition off are not included in thecalculations.

Absolute consumptionDisplays fuel consumed. Themeasurement can be reset at anytime.

Average consumptionDisplays average consumption. Themeasurement can be reset at anytime.

Restart trip computerThe measurement or calculation ofthe following trip computerinformation can be restarted:■ Distance,■ Average speed,■ Absolute consumption,■ Average consumption.Select BC 1 or BC 2 from the BoardComputer menu.

92 Instruments and controls

The information of the two tripcomputers can be reset separately,making it possible to evaluate datafrom different time periods.Select the required trip computerinformation and confirm.

To reset all information of a tripcomputer, select menu item Allvalues.

Stop watch

Select menu item Stop Watch fromthe Board Computer menu.To start, select menu item Start. Tostop, select menu item Stop.To reset, select menu item Reset.The relevant stop watch display canbe selected in the Options menu:

Driving Time excl. StopsThe time the vehicle is in motion isrecorded. Stationary time is notincluded.

Instruments and controls 93

Driving Time incl. StopsThe time the vehicle is in motion isrecorded. The time the vehicle isstationary with the ignition switchedon is included.

Travel TimeMeasurement of the time frommanual activation via Start to manualdeactivation via Reset.

Vehicle personalisationThe vehicle-specific functions P1 toP7 can be activated and deactivated.The setting selected is automaticallystored depending on the vehicle keyused.Different settings are stored for eachvehicle key. Use of a specific vehiclekey will activate the settingsassociated with it.A total of up to five vehicle keys canbe programmed separately.Programming permits the technicalprerequisite of the relevant function.To activate and deactivate thefunctions and set the functions,please see the relevant sections.

Programming■ Turn the ignition off, the key must

be in the ignition switch.

■ Pull turn signal stalk and wiper stalksimultaneously to the steeringwheel until you hear a confirmationsignal (approx. 3 seconds).

■ The miles display shows P1.

94 Instruments and controls

■ Push the turn signal stalk (left) upor down and select the desiredfunction P1 - P7.

■ Push the wiper stalk (right) up ordown and select status On or OFF,or input a value for speed (P6) orvalue for volume (P7).

■ Pull turn signal stalk (left) and wiperstalk (right) simultaneously to thesteering wheel until you hear aconfirmation signal (approx.3 seconds).

The selected settings are now storedfor the key in the ignition switch. Toactivate and deactivate the functionsand set the functions selected, pleasesee the relevant sections.Repeat the procedure to programmeadditional keys.

Programmable functionsP1: Switch on the external lightingusing the remote control (Entrylighting). Entry lighting 3 102.P2: Automatic rear windscreen wiperwhen reverse gear is selected. Rearwindow wiperwasher 3 71.P3: Lane change indication: threeflashes when the lever is movedslightly. Turn and lane-changesignals 3 98.

P4: Automatic locking 3 24.P5: Selective unlocking 3 21.P6: Speed warning 3 74.P7: Volume of the acoustic turn signal3 98.

Lighting 95

Lighting

Exterior lighting ............................ 95Interior lighting ........................... 100Lighting features ........................ 102

Exterior lightingLight switch

Turn light switch:AUTO = Automatic light control:

Exterior lighting isswitched on and offautomatically dependingon external lightingconditions.

m = Activation or deactivationof the automatic lightcontrol. Switch turns backto AUTO

8 = sidelights9 = low beam

When switching on the ignition,automatic light control is active.Control indicator 8 3 82.

Tail lightsTail lights are illuminated togetherwith low beam and sidelights.

Automatic light control

96 Lighting

Automatic light control functionWhen the automatic light controlfunction is switched on and theengine is running, the systemswitches between daytime runninglight and low beam depending onexternal lighting conditions.

Daytime running lightDaytime running light increasesvisibility of the vehicle during daylight.Tail lights are not on.

Automatic low beam activationDuring poor lighting conditions thelow beam is switched on.

Tunnel detectionWhen a tunnel is entered the lowbeam is switched on.Adaptive forward lighting 3 97.

High beam

To switch from low to high beam,push lever.To switch to low beam, push leveragain or pull.

Headlight flashTo activate the headlight flash, pulllever.

Headlight rangeadjustmentManual headlight rangeadjustment

To adapt headlight range to thevehicle load to prevent dazzling: Turnthumb wheel ? until the requiredsetting is shown on the miles display.0 = Front seats occupied1 = All seats occupied2 = All seats occupied and load

compartment laden3 = Driver's seat occupied and load

compartment laden

Lighting 97

Headlights when drivingabroadThe asymmetrical headlight beamextends visibility at the edge of theroad at the passenger side.However, when driving in countrieswhere traffic drives on the oppositeside of the road, adjust the headlightsto prevent dazzling of oncomingtraffic.

Vehicles with halogen headlightsystemHave the headlights adjusted by aworkshop.

Vehicles with adaptive forwardlightingAdapting the aim of the headlightbeam:1. Pull headlight flash lever.2. Switch on ignition.3. Hold headlight flash lever. After

approx. 5 seconds the controlindicator B starts flashing and anacoustic signal sounds.

Control indicator B 3 83.Every time the ignition is switched on,B illuminates for approx. 8 seconds.For deactivation, operate the sameprocedure as described above.Control indicator B will illuminate forapprox. 4 seconds when the functionis deactivated.

Adaptive forward lightingAdaptive forward lighting ensuresbetter illumination of bends, crossingsand narrow bends.

Dynamic curve lighting

The light beam pivots based onsteering wheel angle and speed,improving lighting in curves.

Corner lighting

On tight bends or when turning off,depending on the steering angle orthe indicator light signal, an additionalleft or right reflector is switched onwhich illuminates the road in thedirection of travel. It is activated up toa speed of 25 mph.

Reversing functionIf the lights are on, reverse gear isengaged, and the turn signal isactivated, the cornering light on theappropriate side is switched on. Thecornering light stays on for15 seconds once the turn signal hasbeen switched off.Control indicator B 3 83.

98 Lighting

Hazard warning flashers

Operated with the ¨ button.The hazard warning flashers activateautomatically if the airbags deploy.

Turn and lane-changesignals

Lever up = right turn signalLever down = left turn signal

The lever always springs back to itsoriginal position.If the lever is moved past theresistance point, the turn signal isswitched on constantly. When thesteering wheel moves back, the turnsignal is automatically deactivated.

For three flashes, e.g. when changinglanes, press the lever until resistanceis felt and then release. This functioncan be activated or deactivateddepending on the key used 3 93.Move the lever to the resistance pointand hold for longer indication.Switch the turn signal off manually bymoving the lever slightly.

Acoustic turn signalThe volume of the acoustic turn signalcan be adjusted. This function can beprogrammed depending on the keyused 3 93.

Lighting 99

Front fog lights

Operated with the > button.Light switch in position AUTO:switching on front fog lights will switchthe low beam on automatically.

Rear fog lights

Operated with the r button.Light switch in position AUTO:switching on front fog lights will switchthe low beam on automatically.The rear fog light can only beswitched on when both the ignitionand the low beam or sidelights (withfront fog lights) are on.The vehicle rear fog light isdeactivated when towing.

Parking lights

When parked, the parking lights onone side can be activated:1. Set light switch to m or AUTO.2. Ignition off.3. Move turn signal lever all the way

up (right parking lights) or down(left parking lights).

Confirmed by a signal and thecorresponding turn signal controlindicator.To switch it off, switch on the ignitionor move the turn signal lever in theopposite direction.

100 Lighting

Reversing lightsThe reversing lights come on whenthe ignition is on and reverse gear isselected.

Misted light coversThe inside of the light covers may mistup briefly in poor, wet and coldweather conditions, in heavy rain orafter washing. The mist disappearsquickly by itself; to help, switch on theexterior lights.

Interior lightingInstrument panelillumination control

Brightness of the following lights canbe adjusted when the exterior lightsare on:■ Instrument panel illumination■ Info-Display■ Illuminated switches and operation

elementsTurn thumb wheel A until the requiredbrightness is obtained.

Interior lightsDuring entry and exit of the vehicle,the front and centre courtesy lightsautomatically come on and thenswitch off after a delay.

Front courtesy light

Centre switch position: automaticinterior light.To operate manually when the doorsare closed:On = Switch position IOff = Switch position 0

Lighting 101

Front courtesy light with readinglights

Operated with the c button when thedoors are closed.

Rear courtesy lights

Operated with switch.I = On0 = Offcentre = automatic

Load compartment lightingThe lighting switches on when theload compartment is opened.

Reading lights

Operated with a buttons with ignitionon.

102 Lighting

Lighting featuresCentre console lightingSpotlight in interior mirror housing.Daylight-dependent, automaticallyregulated centre console lighting.

Entry lightingAfter unlocking the vehicle, theinstrument panel lighting, the frontand rear foot well lighting and theinformation display come on for a fewseconds.Starting off 3 16.

Peripheral lightingThe exterior lights come on forapprox. 30 seconds.To activate, press button q on theradio remote control twice when thevehicle is locked.Country-specific application: Toswitch on the function, press buttonq on the radio remote control oncewhen the vehicle is locked.

Switching on the ignition or pressingbutton p on the radio remote controlwill deactivate the function.This function can be activated anddeactivated depending on the keybeing used. Vehicle personalisation3 93.

Exit lightingThe exterior lights illuminate forapprox. 30 seconds after the systemis activated and the driver's door isclosed.

Activating

1. Switch off ignition.2. Remove ignition key.3. Open driver's door.4. Pull turn signal lever.5. Close driver's door.

If the driver's door is not closed thelights switch off after two minutes.The lighting is switched offimmediately if inserting the key intothe ignition switch or pulling the turnsignal lever while the driver's door isopen.

Battery dischargeprotectionTo prevent the battery from becomingdischarged, all the interior lighting isswitched off automatically after5 minutes, when the ignition isswitched off.

Climate control 103

Climate control

Climate control systems ............. 103Air vents ..................................... 109Maintenance .............................. 110

Climate control systemsHeating and ventilationsystem

Controls for:■ Temperature■ Fan speed■ Air distributionHeated rear window Ü 3 31.

Temperaturered = warmblue = cold

Heating will not be fully effective untilengine has reached normal operatingtemperature.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Air distributionM = to head areaL = to head area and foot wellK = to foot wellJ = to windscreen, front door

windows and foot welll = to windscreen and front door

windows

Intermediate settings are possible.

Demisting and defrosting thewindows■ Set temperature control to warmest

level.■ Set fan speed to highest level.■ Set air distribution control to l.■ Switch on heated rear window Ü.

104 Climate control

■ Open side air vents as required anddirect them towards door windows.

■ For simultaneous warming of thefoot well, set air distribution controlto J.

NoteIf the settings for demisting anddefrosting are selected, an Autostopwill be inhibited.If the settings for demisting anddefrosting are selected while theengine is in an Autostop, the enginewill restart automatically.

Stop-start system 3 113.

Air conditioning system

In addition to the heating andventilation system, the airconditioning system has:n = cooling4 = air recirculation

Heated seats ß 3 38, Heatedsteering wheel * 3 69.

Cooling nOperated with the n button and isfunctional only when the engine andfan are running.

The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.If no cooling or drying is required,switch the cooling system off to savefuel. When the cooling system isswitched off, no engine restart will berequested by the climate controlsystem during an Autostop.NoteIf the climate control is set tomaximal cooling while the ambienttemperature is high, an Autostopmay be inhibited until the requestedtemperature in the passengercompartment has been reached.If the climate control is set tomaximal cooling while the engine isin an Autostop, the engine mayrestart automatically.

Stop-start system 3 113.

Air recirculation system 4The air recirculation mode is operatedwith the 4 button.

Climate control 105

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

Air distribution to l: Air recirculationis deactivated.In warm and very humid ambient airconditions, the windscreen might mistup from outside, when cold air isdirected to it. If windscreen mists upfrom outside, activate windscreenwiper and deactivate s.

Maximum coolingBriefly open the windows so that hotair can disperse quickly.■ Cooling n on.■ Air circulation system 4 on.

■ Set temperature control to coldestlevel.

■ Set fan speed to highest level.■ Set air distribution control to M.■ Open all vents.

Demisting and defrosting thewindows

■ Cooling n on.■ Set temperature control to warmest

level.■ Set fan speed to highest level.■ Set air distribution control to l.

■ Switch on heated rear window Ü.■ Open side air vents as required and

direct them towards the doorwindows.

NoteIf the settings for demisting anddefrosting are selected, an Autostopwill be inhibited.If the settings for demisting anddefrosting are selected while theengine is in an Autostop, the enginewill restart automatically.

Electronic climate controlsystem

106 Climate control

Controls for:■ Temperature■ Air distribution and menu selection■ Fan speedAUTO = Automatic mode4 = Air recirculatingV = Demisting and defrosting

Heated rear window Ü 3 31.The preselected temperature isautomatically regulated. In automaticmode, the fan speed and airdistribution automatically regulate theair flow.The system can be manually adaptedwith the air distribution and air flowcontrols.

Data is shown on the Info-Display.Setting modifications are brieflyshown in the Info-Display,superimposed over the currentlydisplayed menu.The electronic climate control systemis only fully operational when theengine is running.

Automatic modeBasic setting for maximum comfort:■ Press AUTO button.■ Open all air vents.■ Air conditioning on.■ Set desired temperature.

Temperature preselectionTemperatures can be set to thedesired value.For reasons of comfort, changetemperature only in small increments.If the minimum temperature is set,Lo appears in the display and theelectronic climate control system runsat maximum cooling.If the maximum temperature is set,Hi appears in the display and theelectronic climate control system runsat maximum heating.NoteIf the temperature is set to Lo or Hi,an Autostop will be inhibited.If the temperature is set to Lo or Hiwhile the engine is in an Autostop,the engine will restart automatically.Stop-start system 3 113.

Fan speedThe selected fan speed is indicatedwith x and the number in the display.If the fan is switched off the airconditioning is also deactivated.

Climate control 107

To return to automatic mode: PressAUTO button.

Demisting and defrosting thewindowsPress the V button. V appears inthe display.Temperature and air distribution areset automatically and the fan runs ata high speed.To return to automatic mode: Pressbutton V or AUTO.Switch on heated rear window Ü.NoteIf the V button is pressed with fanswitched on while the engine isrunning, an Autostop will be inhibiteduntil the V button is pressed again.If the V button is pressed with fanswitched on while the engine is in anAutostop, the engine will restartautomatically.

Stop-start system 3 113.

Manual settings in climate menuClimate control system settings canbe changed via the centre control, thebuttons and the menus shown on thedisplay.To view the menu, press the centrecontrol. The Climate menu appears inthe display.Individual menu items are marked byturning the centre control andselected by pressing it.To exit a menu, turn the centre controluntil Return or Main appear andselect.

Air distributionTurn the centre control. The Airdistribut. menu is activated, showingthe possible air distribution settings:Top = to windscreen and front

door windows.Centre = to vehicle occupants.Bottom = to foot well.

The Air distribut. menu can also becalled up via the Climate menu.

Return to automatic air distribution:Deactivate corresponding setting orpress button AUTO.

Cooling

In the Climate menu, select menuitem AC and activate or deactivatecooling.The air conditioning system cools anddehumidifies (dries) when outsidetemperature is above a specific level.Therefore condensation may formand drip from under the vehicle.

108 Climate control

If no cooling or drying is required,deactivate AC to save fuel. When thecooling system is switched off, noengine restart will be requested by theclimate control system during anAutostop.Depending on the vehicle equipment,the display will indicate AC whencooling is activated or Eco when thecooling is deactivated.

On vehicles with stop-start system,two settings for the operation of theclimate control system during anAutostop are available.Select menu item ecoMode.

Select the desired setting:■ Max AutoStop: In this mode the

electronic climate control isoperated with focus on fuelefficiency. The duration of anAutostop is not limited.

■ AC Comfort: In this mode theelectronic climate control isoperated with focus on climatecondition. The duration of anAutostop might be limited tomaintain the requested climatecondition.

Setting modifications are brieflyshown as pop-ups.Selections are indicated by a o infront of the menu item.In either mode, an Autostop will beavailable after the temperature in thepassenger compartment hassufficiently cooled down.Stop-start system 3 113.

Fan regulation in automaticmodeFan regulation in automatic mode canbe adapted.

Select menu item Automatic blowerfrom the Climate menu and select thedesired fan regulation.

Manual air recirculating modeThe manual air recirculating mode isoperated with the 4 button.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen might mistup from outside, when cold air isdirected to it. If windscreen mists upfrom outside, activate windscreenwiper and deactivate s.

Climate control 109

Auxiliary heaterAir heaterQuickheat is an electric auxiliary airheater which automatically warms upthe passenger compartment morequickly.

Coolant heaterDiesel-engined vehicles have a fuel-powered auxiliary heater.

Air ventsAdjustable air ventsAt least one air vent must be openwhile cooling is on in order to preventthe evaporator from icing up due tolack of air movement.

Set the direction of the air flow byturning the adjuster wheel from rightto left and raise or lower the horizontalslats.

To close the vent, turn the adjusterwheel to left or right to its stop.

9 Warning

Do not attach any objects to theslats of the air vents. Risk ofdamage and injury in case of anaccident.

Fixed air ventsAdditional air vents are locatedbeneath the windscreen and doorwindows and in the foot wells.

110 Climate control

MaintenanceAir intake

The air intake in front of thewindscreen in the enginecompartment must be kept clear toallow air intake. Remove any leaves,dirt or snow.

Pollen filterThe pollen filter cleans dust, soot,pollen and spores from the airentering the vehicle through the airintake.

Air conditioning regularoperationIn order to ensure continuouslyefficient performance, cooling mustbe operated for a few minutes once amonth, irrespective of the weatherand time of year. Operation withcooling is not possible when outsidetemperature is too low.

ServiceFor optimal cooling performance, it isrecommended to annually check theclimate control system, startingthree years after initial vehicleregistration, including:■ Functionality and pressure test■ Heating functionality■ Leakage check■ Check of drive belts■ Cleaning of condenser and

evaporator drainage■ Performance check

Driving and operating 111

Driving and operating

Driving hints ............................... 111Starting and operating ............... 111Engine exhaust .......................... 115Automatic transmission .............. 117Manual transmission .................. 120Manual transmissionautomated .................................. 121Brakes ........................................ 125Ride control systems ................. 127Driver assistance systems ......... 128Fuel ............................................ 130Towing ....................................... 137

Driving hintsControl of the vehicleNever coast with engine notrunning (except during anAutostop)Many systems will not function in thissituation (e.g. brake servo unit, powersteering). Driving in this manner is adanger to yourself and others. Allsystems function during an Autostop,but there will be a controlled reductionin power steering assist and vehiclespeed is reduced.Stop-start system 3 113.

PedalsTo ensure the pedal travel isuninhibited, there must be no mats inthe area of the pedals.

Starting and operatingNew vehicle running-inDo not brake unnecessarily hard forthe first few journeys.During the first drive, smoke mayoccur because of wax and oilevaporating off the exhaust system.Park the vehicle in the open for awhile after the first drive and avoidinhaling the fumes.During the running-in period fuel andengine oil consumption may behigher and the cleaning process ofthe diesel particle filter may takeplace more often. Autostop may beinhibited to allow for charging thebattery.Diesel particle filter 3 115.

112 Driving and operating

Ignition switch positions

0 = Ignition off1 = Steering wheel lock released,

ignition off2 = Ignition on, for diesel engine:

preheating3 = Starting

Starting the engine

Operate clutch and brake, if the clutchpedal is not operated the enginemight not start and the controlindicator - could illuminate.Automatic transmission in P or N.Do not operate accelerator pedal.Diesel engine: turn the key to position2 for preheating and wait until controlindicator ! extinguishes.Turn key briefly to position 3 andrelease.Before restarting or to switch off theengine, turn key back to 0.

During an Autostop, the engine canbe started by depressing the clutchpedal.

Starting the vehicle at lowtemperaturesThe start of the engine withoutadditional heaters is possible down to-25 °С for diesel engines and -30 °Cfor petrol engines. Required is anengine oil with the correct viscosity,the correct fuel, performed servicesand a sufficiently charged battery.With temperatures below -30 °C theautomatic transmission need awarming phase of approx. 5 minutes.The selector lever must be in positionP.

Turbo engine warm-upUpon start-up, engine availabletorque may be limited for a short time,especially when the enginetemperature is cold. The limitation isto allow the lubrication system to fullyprotect the engine.

Driving and operating 113

Overrun cut-offThe fuel supply is automatically cut offduring overrun, i.e. when the vehicleis driven with a gear engaged butaccelerator is released. Overrun cut-off is deactivated if catalytic convertertemperature is high.

Stop-start systemThe stop-start system helps to savefuel and to reduce the exhaustemissions. When conditions allow, itswitches off the engine as soon as thevehicle is at a low speed or at astandstill, e.g. at a traffic light or in atraffic jam. It starts the engineautomatically as soon as the clutch isdepressed. A battery sensor ensuresthat an Autostop is only performed ifthe battery is sufficiently charged fora restart.

ActivationThe stop-start system is available assoon as the engine is started, thevehicle starts-off and the conditionsas stated below in this section arefulfilled.

Deactivation

Deactivate the stop-start systemmanually by pressing the eco button.The deactivation is indicated by theLED in the button going off.

AutostopIf the vehicle is at a low speed or at astandstill, activate an Autostop asfollows:■ Depress the clutch pedal■ shift the selector lever to neutral■ release the clutch pedalThe engine will be switched off whilethe ignition stays on.

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.During an Autostop, the heatingperformance, power steering andbrake performance will bemaintained.

Conditions for an AutostopThe stop-start system checks if eachof the following conditions is fulfilled.■ The stop-start system is not

manually deactivated■ the bonnet is fully closed■ the driver's door is closed or the

driver's seat belt is fastened

114 Driving and operating

■ the battery is sufficiently chargedand in good condition

■ the engine is warmed up■ the engine coolant temperature is

not too high■ the engine exhaust temperature is

not too high, e.g. after driving withhigh engine load

■ the ambient temperature is not toolow

■ the defrosting function is notactivated

■ the climate control system allowsan Autostop

■ the brake vacuum is sufficient■ the self-cleaning function of the

diesel particle filter is not active■ the vehicle has moved since the

last AutostopOtherwise an Autostop will beinhibited.An Autostop may become lessavailable as the ambient temperatureapproaches the freezing point.

Certain settings of the climate controlsystem may inhibit an Autostop. Seeclimate control chapter for moredetails.Immediately after motorway drivingan Autostop may be inhibited.New vehicle running-in 3 111.

Battery discharge protectionTo ensure reliable engine restarts,several battery discharge protectionfeatures are implemented as part ofthe stop-start system.

Power saving measuresDuring an Autostop, several electricalfeatures such as rear window heatingare disabled or switched into a powersaving mode. The fan speed of theclimate control system may bereduced to save power.

Restart of the engine by thedriverDepress the clutch pedal to restart theengine.

The engine start is indicated by theneedle at the idle speed position inthe tachometer.If the selector lever is shifted out ofneutral before depressing the clutchfirst, control indicator - illuminates.Control indicator - 3 79.

Restart of the engine by thestop-start systemThe selector lever has to be in N toenable an automatic restart.If one of the following conditionsoccurs during an Autostop, theengine will be restarted automaticallyby the stop-start system.■ The stop-start system is manually

deactivated■ the bonnet is opened■ the driver's seat belt is unfastened

and the driver's door is opened■ the engine temperature is too low■ the battery is discharged■ the brake vacuum is not sufficient■ the vehicle starts to move■ the defrosting function is activated

Driving and operating 115

■ the climate control system requestsan engine start

■ the air conditioning is manuallyswitched on

If the bonnet is not fully closed, awarning message is displayed in theDriver Information Centre.If an electrical accessory, e.g. aportable CD player, is connected tothe power outlet, a brief power dropduring restart might be noticeable.

Parking■ Do not park the vehicle on an easily

ignitable surface. The hightemperature of the exhaust systemcould ignite the surface.

■ Always apply parking brake withoutpressing release button. Apply asfirmly as possible on downhill oruphill slopes. Depress the footbrake at the same time to reduceoperating force.

■ Switch off the engine and ignition.Turn the steering wheel until thesteering wheel lock engages.

■ If the vehicle is on a level surface oruphill slope, engage first gear or setthe selector lever to P beforeswitching off the ignition. On anuphill slope, turn the front wheelsaway from the kerb.If the vehicle is on a downhill slope,engage reverse gear or set theselector lever to P before switchingoff the ignition. Turn the frontwheels towards the kerb.

■ Lock the vehicle and activate theanti-theft locking system and theanti-theft alarm system.

Engine exhaust

9 Danger

Engine exhaust gases containpoisonous carbon monoxide,which is colourless and odourlessand could be fatal if inhaled.If exhaust gases enter the interiorof the vehicle, open the windows.Have the cause of the faultrectified by a workshop.Avoid driving with an open loadcompartment, otherwise exhaustgases could enter the vehicle.

Diesel particle filterThe diesel particle filter system filtersharmful soot particles out of theexhaust gases. The system includesa self-cleaning function that runsautomatically during driving. The filteris cleaned by burning off the sootparticles at high temperature. Thisprocess takes place automaticallyunder set driving conditions and maytake up to 25 minutes. Fuel

116 Driving and operating

consumption may be higher duringthis period. The emission of smellsand smoke during this process isnormal.

Under certain driving conditions, e.g.short distances, the system cannotclean itself automatically.If the filter requires cleaning andprevious driving conditions did notenable automatic cleaning, controlindicator ! flashes. Continue driving,keeping engine speed above2000 rpm. Shift down if necessary.Diesel particle filter cleaning is thenstarted.

Stopping the journey or switching offthe engine during cleaning is notrecommended.

Caution

If the cleaning process isinterrupted more than once, thereis a great risk of provoking severeengine damage.

Cleaning takes place quickest at highengine speeds and loads.

The control indicator ! extinguishesas soon as the self-cleaningoperation is complete.If A illuminates additionally, cleaningis not possible, seek the assistance ofa workshop.

Catalytic converterThe catalytic converter reduces theamount of harmful substances in theexhaust gases.

Driving and operating 117

Caution

Fuel grades other than those listedon pages 3 130, 3 195 coulddamage the catalytic converter orelectronic components.Unburnt petrol will overheat anddamage the catalytic converter.Therefore avoid excessive use ofthe starter, running the fuel tankdry and starting the engine bypushing or towing.

In the event of misfiring, unevenengine running, a reduction in engineperformance or other unusualproblems, have the cause of the faultrectified by a workshop as soon aspossible. In an emergency, drivingcan be continued for a short period,keeping vehicle speed and enginespeed low.

Automatic transmissionThe automatic transmission permitsautomatic gearshifting.

Transmission display

The mode or selected gear is shownin the transmission display.

Selector lever

P = park position, wheels arelocked, engage only when thevehicle is stationary and theparking brake is applied

R = reverse gear, engage onlywhen vehicle is stationary

N = neutral positionD = automatic mode with all gears.

The selector lever is locked in P andcan only be moved when the ignitionis on and the brake pedal is applied.To engage P or R, press the releasebutton on selector lever.

118 Driving and operating

The engine can only be started withlever in position P or N. When positionN is selected, press brake pedal orapply parking brake before starting.Do not accelerate while engaging agear. Never depress the acceleratorpedal and brake pedal at the sametime.When a gear is engaged, the vehicleslowly begins to creep when thebrake is released.

Gears 3, 2, 13, 2, 1 = Transmission does not

shift above the selectedgear.

Press button on selector lever toengage 3 or 1.Only select 3, 2 or 1 to preventautomatic upshifting or as an aid inengine braking.

Engine brakingTo utilise the engine braking effect,select a lower gear in good time whendriving downhill.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between D and R in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingApply the parking brake and engageP.The ignition key can only be removedwhen the selector lever is in positionP.

Electronic drivingprogrammes■ Following a cold start, the operating

temperature programme increasesengine speed to quickly bring thecatalytic converter to the requiredtemperature.

■ The automatic neutral shift functionautomatically shifts to idling whenthe vehicle is stopped with aforward gear engaged.

■ The adaptive programme tailorsgearshifting to the drivingconditions, e.g. greater load orgradients.

Winter programme T

Activate the Winter programme toassist starting-off on a slippery roadsurface.

Driving and operating 119

ActivationPress the T button with P, R, N, D or3 engaged. The vehicle starts off in3rd gear.

DeactivationThe Winter programme is switched offby:■ pressing the T button again,■ manually selecting 2 or 1,■ turning off the ignition,■ or if the transmission oil

temperature is too high.

Kickdown

If the accelerator pedal is pressedpast the pressure point, thetransmission shifts to a lower geardepending on engine speed.

FaultIn the event of a fault, A illuminates.The transmission no longer shiftsautomatically. Continued travel ispossible with manual shifting.2nd gear is not available. Manualshifting:1 = 1st gear2 = 3rd gear3, D = 4th gear

Have the cause of the fault remediedby a workshop.

Interruption of powersupplyIn the event of an interruption ofpower supply, the selector levercannot be moved out of the Pposition.If the battery is discharged, start thevehicle using jump leads 3 178.

If the battery is not the cause of thefault, release selector lever:1. Apply parking brake.

2. Release selector lever trim fromcentre console at front, foldupwards and rotate to the left.

120 Driving and operating

3. Push the yellow catch forwardwith a screwdriver and move theselector lever out of P. If P isengaged again, the selector leverwill be locked in position again.Have the cause of the powersupply interruption remedied by aworkshop.

4. Mount selector lever trim oncentre console and refit.

Manual transmission

To engage reverse, with the vehiclestationary wait 3 seconds afterdepressing the clutch pedal and thenpress the release button on theselector lever and engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Do not grind the clutch unnecessarily.When operating, depress the clutchpedal completely. Do not use thepedal as a foot rest.

Caution

It is not advisable to drive with thehand resting on the selector lever.

Driving and operating 121

Manual transmissionautomatedThe Easytronic transmission permitsmanual (manual mode) or automaticgear shifting (automatic mode), bothwith automatic clutch control.

Transmission display

Shows the mode and current gear.The display flashes for a few secondswhen A, M or R is selected with theengine running and the foot brake notactivated.

Starting the engineDepress the foot brake when startingthe engine. If the foot brake is notdepressed, j illuminates in theinstrument, "N" flashes in thetransmission display and the enginecannot be started.Starting is not possible if all brakelights fail.When the foot brake is depressed, thetransmission automatically shifts toN upon start. There may be a slightdelay.

Selector lever

Always move the selector lever in theappropriate direction as far as it willgo. Upon release, it automaticallyreturns to the centre position.N = Neutral position.A = Switch between automatic and

manual mode. Thetransmission display shows Aor M.

R = Reverse gear. Engage onlywhen vehicle is stationary.

+ = Shift to a higher gear.- = Shift to a lower gear.

Starting offDepress the foot brake and move theselector lever to A, + or -. Thetransmission is in automatic modeand first gear is engaged. If R isselected, reverse gear is engaged.The vehicle starts to move when thebrake is released.To start off without depressing thefoot brake, accelerate immediatelyafter engaging a gear.

122 Driving and operating

If neither the accelerator nor thebrake pedal are depressed, no gearis engaged and A or R flashes for abrief time in the display.

Stopping the vehicleIn A, first gear is engaged and theclutch is released when the vehicle isstopped. In R, reverse gear remainsengaged.

Engine braking

Automatic modeWhen driving downhill, the manualtransmission automated does notshift into higher gears until a fairlyhigh engine speed has been reached.It shifts down in good time whenbraking.

Manual modeTo utilise the engine braking effect,select a lower gear in good time whendriving downhill.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between R and A (or + or -) in arepeat pattern. Do not race the engineand avoid sudden acceleration.

ParkingApply the parking brake. The mostrecently engaged gear (seetransmission display) remainsengaged. With N, no gear is engaged.When the ignition is switched off thetransmission no longer responds tomovement of the selector lever.

Manual modeIf a higher gear is selected when theengine speed is too low, or a lowergear when the speed is too high, theshift is not executed. This preventsthe engine from running at too low ortoo high an engine speed.If engine speed is too low, thetransmission automatically shifts to alower gear.

If engine speed is too high, thetransmission only switches to a highergear via kickdown.When + or - is selected in automaticmode, the transmission switches tomanual mode and shifts accordingly.

Electronic drivingprogrammes■ Following a cold start, the operating

temperature programme increasesengine speed to quickly bring thecatalytic converter to the requiredtemperature.

■ The adaptive programme tailorsgearshifting to the drivingconditions, e.g. greater load orgradients.

Driving and operating 123

Sport mode

Shift times are reduced when theSport mode is enabled, and the gearsare shifted at higher engine speeds,although not when cruise control isactivated.

ActivationPress the S button.Control indicator 1 3 80.

DeactivationThe Sport mode is switched off by:■ pressing the S button again,■ turning off the ignition,■ activating the winter mode T.

Winter mode T

Activate the Winter mode if you haveproblems starting off on a slipperyroad surface.

ActivationPress the T button. The transmissionswitches to automatic mode. Thevehicle starts off in 2nd gear. Sportmode is deactivated.

DeactivationThe Winter mode is switched off by:■ pressing the T button again,■ turning off the ignition,■ switching to manual mode (when

switched back to automatic mode,the Winter programme is againactive),

■ when clutch temperature is toohigh.

124 Driving and operating

Kickdown

If the accelerator pedal is pressedpast the pressure point, thetransmission shifts to a lower geardepending on engine speed.

FaultTo prevent damage to the manualtransmission automated, the clutch isengaged automatically at high clutchtemperatures.A illuminates in the event of a fault.Continued driving is possible. Manualmode cannot be used for shifting.

If F appears in the transmissiondisplay, continued driving is notpossible.Have the cause of the fault remediedby a workshop.

Interruption of powersupplyThe clutch is not disengaged if thereis an interruption of the power supplywhen a gear is engaged. The vehiclecannot move.If the battery is discharged, start thevehicle using jump leads 3 178.If the cause of the fault is not adischarged battery, seek theassistance of a workshop.

If the vehicle must be moved out ofthe flow of traffic, disengage theclutch as follows:1. Apply parking brake and switch off

ignition.2. Open the bonnet 3 144.3. Clean the transmission around

the cap so that no dirt can get intothe opening when the cap isremoved.

4. Rotate cap to slacken and removeby lifting upwards.

Driving and operating 125

5. Using a flat-head screwdriver,turn the adjusting screw under thecap clockwise until clearresistance can be felt. The clutchhas now been disengaged.

6. Refit cleaned cap. The cap mustbe in full contact with the housing.

Caution

Do not turn beyond the resistancesince this could damage thetransmission.

Caution

Towing the vehicle and startingthe engine is not permitted whenthe clutch has been disengaged inthis way, although the vehicle canbe moved a short distance.

Seek the immediate assistance of aworkshop.

BrakesThe brake system comprises twoindependent brake circuits.If a brake circuit fails, the vehicle canstill be braked using the other brakecircuit. However, braking effect isachieved only when you depress thebrake pedal firmly. You need to useconsiderably more force for this. Thebraking distance is extended. Seekthe assistance of a workshop beforecontinuing your journey.When the engine is not running, thesupport of the brake servo unitdisappears once the brake pedal hasbeen depressed once or twice.Braking effect is not reduced, butbraking requires significantly greaterforce. It is especially important to bearthis in mind when being towed.Control indicator R 3 79.

Antilock brake systemAntilock brake system (ABS)prevents the wheels from locking.

ABS starts to regulate brake pressureas soon as a wheel shows a tendencyto lock. The vehicle remainssteerable, even during hard braking.ABS control is made apparent thougha pulse in the brake pedal and thenoise of the regulation process.For optimum braking, keep the brakepedal fully depressed throughout thebraking process, despite the fact thatthe pedal is pulsating. Do not reducethe pressure on the pedal.After starting off the system performsa self-test which may be audible.Control indicator u 3 80.

Adaptive brake lightDuring full braking, all three brakelamps flash for the duration of ABScontrol.

126 Driving and operating

Fault

9 Warning

If there is a fault in the ABS, thewheels may be liable to lock dueto braking that is heavier thannormal. The advantages of ABSare no longer available. Duringhard braking, the vehicle can nolonger be steered and mayswerve.

Have the cause of the fault remediedby a workshop.

Parking brake

Always apply parking brake firmlywithout operating the release button,and apply as firmly as possible on adownhill or uphill slope.To release the parking brake, pull thelever up slightly, press the releasebutton and fully lower the lever.To reduce the operating forces of theparking brake, depress the foot brakeat the same time.Control indicator R 3 79.

Brake assistIf the brake pedal is depressedquickly and forcefully, maximumbrake force is automatically applied(full braking).Maintain steady pressure on thebrake pedal for as long as full brakingis required. Maximum brake force isautomatically reduced when thebrake pedal is released.

Hill start assistThe system helps prevent unintendedmovement when driving away oninclines.When releasing the foot brake afterstopping on an incline, the brakesremain on for a further two seconds.The brakes release automatically assoon as the vehicle begins toaccelerate.The hill start assist is not active duringan Autostop.

Driving and operating 127

Ride control systemsElectronic stabilityprogramElectronic stability program(ESP®Plus) improves driving stabilitywhen necessary, regardless of thetype of road surface or tyre grip. It alsoprevents the drive wheels fromspinning.As soon as the vehicle starts toswerve (understeer/oversteer),engine output is reduced and thewheels are braked individually. Thisconsiderably improves the drivingstability of the vehicle on slippery roadsurfaces.ESP®Plus is operational as soon ascontrol indicator v extinguishes.When ESP®Plus comes into action vflashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator v 3 80.

Deactivation

ESP®Plus can be deactivated bypressing the v button.

When ESP®Plus is deactivated thecontrol indicator v illuminates.ESPoff also appears in the servicedisplay.

9 Warning

Do not deactivate ESP®Plus if arun-flat tyre has lost pressure.

ESP®Plus is reactivated by pressingthe v button. ESPon appears in theservice display. ESP®Plus is alsoreactivated the next time the ignitionis switched on.

128 Driving and operating

Driver assistancesystemsCruise controlThe cruise control can store andmaintain speeds of approx. 20 to120 mph.Deviations from the stored speedsmay occur when driving uphill ordownhill.For safety reasons the cruise controlcannot be activated until the footbrake has been operated once.

Do not use the cruise control if it is notadvisable to maintain a constantspeed.With automatic transmission ormanual transmission automated, onlyactivate cruise control in automaticmode.Control indicator m 3 83.

ActivationTurn switch m up and release: thecurrent speed is stored andmaintained.Vehicle speed can be increased bydepressing the accelerator pedal.When the accelerator pedal isreleased, the previously stored speedis resumed.The speed is saved until the ignitionis switched off.To resume the saved speed, turnswitch g downwards at a speedabove 20 mph.

Increase speedWith cruise control active, turn switchm upwards and hold, or turn brieflyseveral times: speed is increasedcontinuously or in small increments.When switch m is released thecurrent speed is stored andmaintained.

Reduce speedWith cruise control active, turn switchg downwards and hold, or turn brieflyseveral times: speed is reducedcontinuously or in small increments.When switch g is released the currentspeed is stored and maintained.

DeactivationBriefly press the § button: cruisecontrol is deactivated.Automatic deactivation:■ Vehicle speed below approx.

20 mph■ The brake pedal is depressed■ The clutch pedal is depressed■ Selector lever in N.

Driving and operating 129

To reset the saved speed, turn switchg downwards.

Parking assist

The parking assist makes parkingeasier by measuring the distancebetween the vehicle and obstacles,and giving acoustic signals. It is thedriver, however, who bears fullresponsibility for the parkingmanoeuvre.The system consists of four ultrasonicparking sensors in the rear bumper.Control indicator r 3 80.

ActivationWhen reverse gear is engaged, thesystem is activated automatically.

IndicationAn obstacle is indicated by a buzzingsound. The interval between thesounds becomes shorter as thevehicle gets closer to the obstacle.When the distance is less than30 cm, the buzzing is continuous.

DeactivationThe system automatically switchesitself off when reverse gear isdisengaged.

If the vehicle is equipped with ther button, the system can bedeactivated by pressing the button.

FaultIn the event of a fault in the system,r illuminates.Additionally, r flashes if amalfunction of the system due totemporary conditions like snowcovered sensors is detected.Control indicator r 3 80.

Important hints for using theparking assist systems

9 Warning

Under certain circumstances,various reflective surfaces onobjects or clothing as well asexternal noise sources may causethe system to fail to detectobstacles.Special attention must be paid tolow obstacles which can damagethe lower part of the bumper.

130 Driving and operating

Caution

Performance of the sensors canbe reduced when sensors arecovered, e.g. by ice or snow.Performance of the parking assistsystems can be reduced due toheavy loading.Special conditions apply if thereare taller vehicles involved (e.g.off-road vehicles, mini vans,vans). Object identification in theupper part of these vehiclescannot be guaranteed.Objects with a very small reflectioncross-section, e.g. objects ofnarrow size or soft materials, maynot be detected by the system.Parking assist will not avoid acollision with objects which are outof the detection range of thesensors.

NoteThe parking assist systemautomatically detects factory-fittedtowing equipment. It is deactivatedwhen the connector is plugged in.The sensor may detect a non-existent object (echo disturbance)caused by external acoustic ormechanical disturbances.NoteThe parking assist is deactivatedwhen the rear carrier system isextended.

FuelFuel for petrol enginesOnly use unleaded fuel that complieswith European standard EN 228 orE DIN 51626-1 or equivalent.Your engine is capable of runningwith E10 fuel that fulfills thesestandards. E10 fuel contains up to10 % bioethanol.Use fuel with the recommendedoctane rating 3 195. Use of fuel withtoo low an octane rating can reduceengine power and torque and slightlyincreases fuel consumption.

Caution

Do not use fuel or fuel additivesthat contain metallic compoundssuch as manganese-basedadditives. This may cause enginedamage.

Driving and operating 131

Caution

Use of fuel that does not comply toEN 228 or E DIN 51626-1 orequivalent can lead to deposits orengine damage and may affectyour warranty.

Caution

Use of fuel with too low an octanerating could lead to uncontrolledcombustion and engine damage.

Fuel for diesel enginesOnly use diesel fuel that complieswith EN 590.In countries outside the EuropeanUnion use Euro-Diesel fuel with asulfur concentration below 50 ppm.

Caution

Use of fuel that does not comply toEN 590 or similar can lead toengine powerloss, increased wearor engine damage and may affectyour warranty.

Do not use marine diesel oils, heatingoils, Aquazole and similar diesel-water emulsions. Diesel fuels mustnot be diluted with fuels for petrolengines.

Fuel for liquid gasoperationLiquid gas is known as LPG(Liquefied Petroleum Gas) or underits French name GPL (Gaz de PétroleLiquéfié). LPG is also known asAutogas.LPG consists mainly of propane andbutane. The octane rating is between105 and 115, depending on thebutane proportion. LPG is storedliquid at around 5 - 10 bar pressure.

The boiling point depends on thepressure and mixing ratio. At ambientpressure, it is between -42 °C (purepropane) and -0.5 °C (pure butane).

Caution

The system works at an ambienttemperature of approx. -8 °C to100 °C.

Full function of the LPG system canonly be guaranteed with liquid gaswhich complies with the minimumrequirements of DIN EN 589.

Fuel selector

132 Driving and operating

Pressing the LPG button switchesbetween petrol and liquid gasoperation as soon as the requiredparameters (coolant temperature,gas temperature and minimumengine speed) have been reached.The requirements are usually fulfilledafter approx. 60 seconds (dependingon exterior temperature) and the firstfirm press on the accelerator. TheLED status shows the currentoperating mode.1 off = petrol operation1 illuminates = liquid gas

operation1 flashes = no switching is

possible, one typeof fuel is empty

As soon as the liquid gas tanks areempty, petrol operation isautomatically engaged until theignition is switched off.Every six months, run the petrol tankdown until control indicator Yilluminates, then refuel. This helpsmaintain fuel quality and systemfunction for petrol operation.

Fill the tank completely at regularintervals to prevent corrosion in thetank.

Faults and remediesIf gas mode is not possible, check thefollowing:■ Is there enough liquid gas present?■ Is there enough petrol present for

starting?Due to extreme temperatures incombination with the gascomposition, it may take slightlylonger before the system switchesfrom petrol to liquid gas mode.In extreme situations, the system mayalso switch back to petrol mode if theminimum requirements are notfulfilled.Seek the assistance of a workshop inthe event of all other faults.

Caution

Repairs and adjustments may onlybe made by trained specialists inorder to maintain the safety andwarranty on the LPG system.

Liquid gas is given a particular odour(odorised) so that any leaks can bedetected easily.

9 Warning

If you smell gas in the vehicle or inthe immediate vicinity, switch topetrol mode immediately. Nosmoking. No naked flames orignition sources.

If possible, close the manual shut-offvalve on the multivalve. Themultivalve is located on the liquid gastank in the load compartment,underneath the rear floor cover.

Driving and operating 133

Turn the thumb wheel clockwise.If no further gas odour is perceptiblewhen the manual shut-off valve isclosed, the vehicle can be used inpetrol mode. If the gas odour persists,do not start the engine. Have thecause of the fault remedied by aworkshop.When using underground car parks,follow the instructions of the operatorand local laws.NoteIn the event of an accident, switch offthe ignition and lights. Close themanual shut-off valve on multivalve.

Refuelling

9 Danger

Before refuelling, switch off engineand any external heaters withcombustion chambers (identifiedby sticker on fuel filler flap). Switchoff any mobile phones.Follow the operating and safetyinstructions of the filling stationwhen refuelling.

9 Danger

Fuel is flammable and explosive.No smoking. No naked flames orsparks.If you can smell fuel in yourvehicle, have the cause of thisremedied immediately by aworkshop.

Caution

In case of misfuelling, do notswitch on ignition.

Fuel filler flap is located at right rearside of vehicle.With a central locking system withremote control, the tank flap isunlocked at the same time as thedoors.Pul flap at the recess and open.

134 Driving and operating

Unlock the fuel filler cap with theignition key. To open, turn the capslowly to the left. The fuel filler capcan be retained in the bracket on thefuel filler flap.For refuelling, fully insert the pumpnozzle and switch it on.After automatic cut-off, it can betopped up with max. two doses of fuel.

Caution

Wipe off any overflowing fuelimmediately.

To close, turn the fuel filler cap to theright until it clicks.Close the flap and let engage.

Liquid gas refuellingFollow the operating and safetyinstructions of the filling station whenrefuelling.The filling valve for the liquid gas isbehind the fuel filler cap.

Unscrew protective cap from the fillerneck.

Fit the required adapter.

ACME Adapter: Screw the nut of thefilling nozzle onto the adapter. Presslocking lever on filler nozzle down.

Driving and operating 135

DISH (Italy) filler neck: Place the fillernozzle into the adapter. Press lockinglever on filler nozzle down.Bayonet filler neck: Place filler nozzleon the adapter and turn to the left orright through one quarter turn. Pulllocking lever of filler nozzle fully.EURO filler neck: Press the fillernozzle onto the adapter until itengages.Press the button of the liquid gassupply point. The filling system stopsor begins to run slowly when 80% ofthe tank volume is reached(maximum fill level).Release button on filling system andthe filling process stops. Release thelocking lever and remove the fillernozzle. A small quantity of liquid gascan escape.Remove adapter and stow in vehicle.Fit protective cap to prevent thepenetration of foreign bodies into thefiller opening and the system.

9 Warning

Due to the system design, anescape of liquid gas afterreleasing the locking lever isunavoidable. Avoid inhaling.

9 Warning

The liquid gas tank may only befilled to 80% for safety reasons.

The multivalve on the liquid gas tankautomatically limits the fill quantity. Ifa larger quantity is added, werecommend not exposing the vehicleto the sun until the excess amounthas been used up.

Filling adapterAs filling systems are notstandardised, different adapters arerequired which are available fromVauxhall Distributors and fromVauxhall Authorised Repairers.

ACME adapter: Belgium, Germany,Ireland, Luxembourg, Switzerland

Bayonet adapter: Netherlands,Norway, Spain, United Kingdom

136 Driving and operating

EURO adapter: Spain

DISH (Italy) adapter: Bosnia-Herzegovina, Bulgaria, Denmark,Estonia, France, Greece, Italy,

Croatia, Latvia, Lithuania,Macedonia, Austria, Poland,Portugal, Romania, Sweden,Switzerland, Serbia, Slovakia,Slovenia, Czech Republic, Turkey,Ukraine, Hungary

Fuel filler capOnly use genuine fuel filler caps.Diesel-engined vehicles have specialfuel filler caps.

Fuel consumption - CO2-EmissionsThe fuel consumption (combined) ofthe model Vauxhall Corsa is within arange of 37 to 85 mpg.The CO2 emission (combined) iswithin a range of 88 to 178 g/km.For the values specific for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

General informationThe official fuel consumption andspecific CO2 emission figures quotedrelate to the EU base model withstandard equipment.Fuel consumption data and CO2emission data are determinedaccording to regulation R (EC) No.715/2007 (in the version respectivelyapplicable), taking into considerationthe vehicle weight in running order, asspecified by the regulation.The figures are provided only for thepurpose of comparison betweendifferent vehicle variants and mustnot be taken as a guarantee for theactual fuel consumption of aparticular vehicle. Additionalequipment may result in slightlyhigher results than the statedconsumption and CO2 figures.Furthermore, fuel consumption isdependent on personal driving styleas well as road and traffic conditions.

Driving and operating 137

TowingGeneral informationOnly use towing equipment that hasbeen approved for your vehicle.Entrust retrofitting of towingequipment to a workshop. It may benecessary to make changes thataffect the cooling system, heatshields or other equipment.Fitting of towing equipment couldcover the opening of the towing eye.If this is the case use the coupling ballbar for towing. Always keep thecoupling ball bar in the vehicle.

Driving characteristics andtowing tipsBefore attaching a trailer, lubricatethe coupling ball. However, do not doso if a stabiliser, which acts on thecoupling ball, is being used to reducesnaking movements.For trailers with low driving stabilityand caravan trailers with a permittedgross vehicle weight of more than

1000 kg a speed of 50 mph must notbe exceeded; the use of a stabiliser isrecommended.If the trailer starts snaking, drive moreslowly, do not attempt to correct thesteering and brake sharply ifnecessary.When driving downhill, drive in thesame gear as if driving uphill anddrive at a similar speed.Adjust tyre pressure to the valuespecified for full load 3 212.

Trailer towingTrailer loadsThe permissible trailer loads arevehicle and engine-dependentmaximum values which must not beexceeded. The actual trailer load isthe difference between the actualgross weight of the trailer and theactual coupling socket load with thetrailer coupled.

The permissible trailer loads arespecified in the vehicle documents. Ingeneral, they are valid for gradientsup to max. 12 %The permitted trailer loads apply up tothe specified incline and up to analtitude of 1000 metres above sealevel. Since engine power decreasesas altitude increases due to the airbecoming thinner, therefore reducingclimbing ability, the permissible grosstrain weight also decreases by 10 %for every 1000 metres of additionalaltitude. The gross train weight doesnot have to be reduced when drivingon roads with slight inclines (less than8 %, e.g. motorways).The permissible gross train weightmust not be exceeded. This weight isspecified on the identification plate3 190.

Vertical coupling loadThe vertical coupling load is the loadexerted by the trailer on the couplingball. It can be varied by changing theweight distribution when loading thetrailer.

138 Driving and operating

The maximum permissible verticalcoupling load (vehicles with 1.2engine: 45 kg, other engines: 55 kg)is specified on the towing equipmentidentification plate and in the vehicledocuments. Always aim for themaximum load, especially in the caseof heavy trailers. The vertical couplingload should never fall below 25 kg.

Rear axle loadWhen the trailer is coupled and thetowing vehicle fully loaded, thepermissible rear axle load (seeidentification plate or vehicledocuments) for passenger vehiclesmay be exceeded by 45 kg and thegross vehicle weight rating by 50 kg(on vehicles with 1.2 engine andspecific rear axle application: 30 kg).For vans the permitted rear axle loadmay be exceeded by 25 kg. Thepermitted total load may be exceededby the following amounts with theengines specified below:A10XEP = 30 kgA12XEL, A12XER,Z12XEP

= 25 kg

Z13DTH, A13DTR = 40 kgZ13DTJ, Z13DTE,A13DTE, A13DTC

= 35 kg

Trailer operation is not permitted forvans with tyre size 215/45 R 17.If the permitted rear axle load isexceeded a maximum speed of60 mph applies. If lower nationalmaximum speeds are specified fortrailer operation, they must becomplied with.

Towing equipment

Caution

When operating without a trailer,remove the coupling ball bar.

Stowage of coupling ball barThe coupling ball bar is stowed in abag in the spare wheel well andsecured to the lashing eyes in theload compartment.

When inserting, fit protective cap overrotary knob with key.

Fitting the coupling ball bar

Driving and operating 139

Push both bolts inwards and removethe cover on the bumper.

Disengage and fold down the socket.Remove the sealing plug from theopening for the coupling ball bar andstow it.

Checking the tensioning of thecoupling ball bar

■ The rotary knob rests on thecoupling ball bar.

■ Green marking on the rotary knobis not visible.

■ Locking pin at the top of thecoupling ball bar is set inwards.

■ The key is in the lock.Otherwise, the coupling ball bar mustbe tensioned before it is inserted intothe coupling housing:

■ Place the key in the lock and unlockthe coupling ball bar.

■ Push the rotary knob onto thecoupling ball bar and rotate rightwhile pressed down until itengages. The key remains in thelock.

140 Driving and operating

Inserting the coupling ball bar

Insert the tensioned coupling ball barin the opening and push firmlyupwards until it audibly engages.The rotary knob snaps back into itsoriginal position resting against thecoupling ball bar without a gap.

9 Warning

Do not touch rotary knob duringinsertion.

Green marking on the rotary knob isvisible.Lock coupling ball bar and removekey.

Eye for break-away stopping cableAttach breakaway stopping cable toeye.

Check that the coupling ball bar iscorrectly installed■ Green marking on rotary knob is

visible.■ There must be no gap between the

rotary knob and the coupling ballbar.

■ The coupling ball bar must be firmlyengaged in the opening.

■ The coupling ball bar must belocked and the key removed.

9 Warning

Towing a trailer is permitted onlywhen a coupling ball bar is fittedcorrectly. If the coupling ball bardoes not engage correctly, seekthe assistance of a workshop.

Driving and operating 141

Dismounting the coupling ballbar

Insert the key in the lock and unlockthe coupling ball bar.Push the rotary knob onto thecoupling ball bar and rotate right whilepressed down until it engages. Pullout the ball bar downwards.Insert sealing plug in opening forcoupling ball bar. Fold away socket.Place cover on bumper and push bothbolts outwards.

142 Vehicle care

Vehicle care

General Information ................... 142Vehicle checks ........................... 143Bulb replacement ....................... 150Electrical system ........................ 163Vehicle tools .............................. 167Wheels and tyres ....................... 169Jump starting ............................. 178Towing ....................................... 180Appearance care ....................... 182

General InformationAccessories and vehiclemodificationsWe recommend using genuine partsand accessories and factoryapproved parts specific for yourvehicle type. We cannot assess orguarantee reliability of other products- even if they have a regulatory orotherwise granted approval.Do not make any modifications to theelectrical system, e.g. changes ofelectronic control units (chip tuning).

Caution

When transporting the vehicle ona train or on a recovery vehicle, themud flaps might be damaged.

Vehicle storageStorage for a long period of timeThe following must be carried out ifthe vehicle is to be stored for severalmonths:■ Wash and wax the vehicle.■ Have the wax in the engine

compartment and underbodychecked.

■ Clean and preserve rubber seals.■ Fill up fuel tank completely.■ Change engine oil.■ Drain washer fluid reservoir.■ Check coolant antifreeze and

corrosion protection.■ Adjust tyre pressure to the value

specified for full load.■ Park vehicle in dry, well ventilated

place. Engage first or reverse gearor set selector lever to P. Preventthe vehicle from rolling.

■ Do not apply parking brake.

Vehicle care 143

■ Open bonnet, close all doors andlock the vehicle.

■ Disconnect the clamp from thenegative terminal of the vehiclebattery. Beware that all systems arenot functional, e.g. anti-theft alarmsystem.

Putting back into operationFollowing must be done if the vehicleis putting back into operation:■ Connect the clamp to the negative

terminal of the vehicle battery.Activate the electronics of thepower windows.

■ Check tyre pressure.■ Fill up the washer fluid reservoir.■ Check the engine oil level.■ Check the coolant level.■ Fit the number plate if necessary.

End-of-life vehiclerecoveryInformation on end-of-life vehiclerecovery centres and the recycling ofend-of-life vehicles is available on our

website, where legally required. Onlyentrust this work to an authorisedrecycling centre.Gas vehicles must be recycled by aservice centre authorised for gasvehicles.

Vehicle checksPerforming work

9 Warning

Only perform engine compartmentchecks when the ignition is off.The cooling fan may startoperating even if the ignition is off.

144 Vehicle care

9 Danger

The ignition system and Xenonheadlights use extremely highvoltage. Do not touch.

The caps for topping up the engine oil,the coolant, the washer fluid and theoil dipstick handle are yellow, for easeof identification.

BonnetOpening

Pull the release lever and return it toits original position.

Lift the safety catch upwards andopen the bonnet.Air intake 3 110.

Secure the bonnet support.If the bonnet is opened during anAutostop, the engine will be restartedautomatically for safety reasons.

ClosingBefore closing the bonnet, press thesupport into the holder.Lower the bonnet and allow it to dropinto the catch. Check that the bonnetis engaged.

Vehicle care 145

Engine oilCheck the engine oil level manuallyon a regular basis to prevent damageto the engine. Ensure that the correctspecification of oil is used.Recommended fluids and lubricants3 187.Check with the vehicle on a levelsurface. The engine must be atoperating temperature and switchedoff for at least 5 minutes.Pull out the dipstick, wipe it clean,insert it to the stop on the handle, pullout and read the engine oil level.Insert dipstick to the stop on thehandle and make half a turn.

Different dipsticks are useddepending on engine variant.

When the engine oil level hasdropped to the MIN mark, top upengine oil.

We recommend the use of the samegrade of engine oil that was used atthe last oil change.The engine oil level must not exceedthe MAX mark on the dipstick.

Caution

Overfilled engine oil must bedrained or suctioned out.

Capacities 3 211.

146 Vehicle care

Fit the cap on straight and tighten it.

Engine coolantThe coolant provides freezeprotection down to approx. -28 °C.

Caution

Only use approved antifreeze.

Coolant level

Caution

Too low a coolant level can causeengine damage.

If the cooling system is cold, thecoolant level should be above theKALT/COLD mark. Top up if the levelis low.

9 Warning

Allow the engine to cool beforeopening the cap. Carefully openthe cap, relieving the pressureslowly.

Top up with antifreeze. If noantifreeze is available, use clean tapwater or distilled water. Install the captightly. Have the antifreeze

concentration checked and have thecause of the coolant loss remedied bya workshop.

Washer fluid

Fill with clean water mixed with asuitable quantity of washer fluid whichcontains antifreeze. For the correctmixing ratio refer to the washer fluidcontainer.

Vehicle care 147

Caution

Only washer fluid with a sufficientantifreeze concentration providesprotection at low temperatures ora sudden drop in temperature.

BrakesA squealing noise indicates that thebrake lining is at its minimumthickness. Continued driving ispossible but have the brake liningreplaced as soon as possible.Once new brake linings are installed,do not brake unnecessarily hard forthe first few journeys.

Brake fluid

9 Warning

Brake fluid is poisonous andcorrosive. Avoid contact with eyes,skin, fabrics and painted surfaces.

The brake fluid level must be betweenthe MIN and the MAX marks.When topping up, ensure maximumcleanliness as contamination of thebrake fluid can lead to brake systemmalfunctions. Have the cause of theloss of brake fluid remedied by aworkshop.Only use high-performance brakefluid approved for the vehicle, Brakeand clutch fluid 3 187.

BatteryVehicles without stop-start systemwill be equipped with a lead acidbattery. Vehicles with stop-startsystem will be equipped with an AGMbattery which is not a lead acidbattery. The vehicle battery ismaintenance-free provided that thedriving profile allows sufficientcharging of the battery. Short-distance-driving and frequent enginestarts can discharge the battery.Avoid the use of unnecessaryelectrical consumers.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.

148 Vehicle care

Laying up the vehicle for more than4 weeks can lead to batterydischarge. Disconnect the clamp fromthe negative terminal of the vehiclebattery.Ensure the ignition is switched offbefore connecting or disconnectingthe vehicle battery.The anti-theft alarm siren must bedeactivated as follows: switch theignition on then off, disconnect thevehicle's battery within 15 seconds.

Warning label

Meaning of symbols:■ No sparks, naked flames or

smoking.■ Always shield eyes. Explosive

gases can cause blindness orinjury.

■ Keep the battery out of reach ofchildren.

■ The battery contains sulfuric acidwhich could cause blindness orserious burn injuries.

■ See the Owner’s Manual for furtherinformation.

■ Explosive gas may be present inthe vicinity of the battery.

Replacing the batteryNoteAny deviation from the instructionsgiven in this paragraph may lead toa temporary deactivation of the stop-start system.

When the battery is being replaced,please ensure that there are no openventilation holes in the vicinity of thepositive terminal. If a ventilation holeis open in this area, it must be closed

off with a dummy cap, and theventilation in the vicinity of thenegative terminal must be opened.Only use batteries that allow the fusebox to be mounted above the battery.In vehicles with an AGM (AbsorptiveGlass Mat) battery, ensure to havethe battery replaced with an AGMbattery.

An AGM battery can be identified bythe label on the battery. Werecommend the use of an originalVauxhall battery.

Vehicle care 149

NoteUsing an AGM battery different fromthe original Vauxhall battery mightresult in a lower performance of thestop-start system.

We recommend that you have thebattery replaced by a workshop.Stop-start system 3 113.

Charging the battery

9 Warning

On vehicles with an AGM battery,ensure that the charging potentialdoes not exceed 14.6 volts whenusing a battery charger. Otherwisethe battery might be damaged.

Jump starting 3 178.

Diesel fuel systembleedingIf the tank has been run dry, the dieselfuel system must be bled. Switch onthe ignition three times for15 seconds at a time. Then crank theengine for a maximum of40 seconds (for technical reasonsonly 30 seconds are possible withengine A 17 DTS). Repeat thisprocess after no less than5 seconds. If the engine fails to start,seek the assistance of a workshop.

Wiper blade replacementService setting for frontwindscreen wipers

Switch off the ignition but do notremove ignition key or open driver'sdoor.Within 4 seconds, push the wiperlever down and release as soon asthe wipers are vertical.

150 Vehicle care

Wiper blades on the windscreen

Lift the wiper arm, tilt wiper blade at a90° to the wiper arm and remove tothe side.

Wiper blade on the rear window

Lift wiper arm. Disengage wiper bladeas shown in illustration and remove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Bulb replacementSwitch off the ignition and switch offthe relevant switch or close the doors.Only hold a new bulb at the base! Donot touch the bulb glass with barehands.Use only the same bulb type forreplacement.

To replace bulbs on the right side ofthe engine compartment, detach theair hose from the air filter.On VXR vehicles, it is recommendedto have the bulbs replaced by aworkshop.

Vehicle care 151

To replace the bulb on the left-handside, remove fuse box cover 3 165,and also remove windscreen washersystem reservoir filler neck fromabove. Washer fluid may escape ifthe reservoir is full to the top.

Halogen headlights

Headlights have separate systems forlow beam 1 (outer bulb), high beam2 (inner bulb) and daytime runninglight/side light 3.

Low beam

1. Disengage wire clip and removeprotective cover 1.

2. Press base to the side andremove bulb from reflector.

3. Detach plug connector from bulb.4. Insert new bulb in reflector so that

the locating tab of the bulb holderaligns with the reflector recess.

5. Engage bulb.6. Attach connector to bulb.7. Put on protective cover and

engage wire clip.

152 Vehicle care

High beam

1. Rotate protective cover 2anticlockwise and remove.

2. Detach wiring plug from bulb.

3. Disengage spring clip fromretainer by moving and swivellingto the side.

4. Remove bulb from reflectorhousing.

5. When installing the new bulb,insert lugs in the reflectorrecesses.

6. Install spring clip, plug connectoronto bulb.

7. Install protective cover.

Daytime running light/side light

1. Rotate bulb holder 3anticlockwise to disengage.Withdraw sidelight bulb holderfrom reflector.

Vehicle care 153

2. Remove bulb from socket, insertnew bulb.

3. Insert bulb holder in reflector sothat the locating tab of the bulbholder aligns with the reflectorrecess.

4. Rotate clockwise to engage.

Front turn signal lightFront turn signal lights are equippedwith longlife bulbs. In case of failure,have bulb replaced by a workshop.

Adaptive forward lighting

Headlights have separate systems forlow and high beam 1 (outer bulb),cornering light 2 (inner bulb) anddaytime running light/side light 3.

Low/high beam

1. Disengage wire clip and removeprotective cover 1.

154 Vehicle care

2. Rotate bulb holder anticlockwiseto disengage.Withdraw bulb holder fromreflector.

3. Insert new bulb in reflector so thatthe locating tab of the bulb holderaligns with the reflector recess.

4. Engage bulb holder by turningclockwise.

5. Put on protective cover andengage wire clip.

Daytime running light/Side light

1. Rotate bulb holder 3anticlockwise to disengage.Withdraw bulb holder fromreflector.

2. Remove bulb from socket, insertnew bulb.

3. Insert bulb holder in reflector sothat the locating tab of the bulbholder aligns with the reflectorrecess.

4. Rotate clockwise to engage.

Vehicle care 155

Cornering light

1. Rotate protective cover 2anticlockwise and remove.

2. Detach wiring plug from bulb.

3. Disengage spring clip fromretainer by moving and swivellingto the side.

4. Remove bulb from reflectorhousing.

5. When installing the new bulb,insert lugs in the reflectorrecesses.

6. Install spring clip, plug connectoronto bulb.

7. Install protective cover.

Front turn signal light

1. Disengage wire clip and removeprotective cover 1.

156 Vehicle care

2. Rotate bulb holder anticlockwiseto disengage.Withdraw bulb holder fromreflector.

3. Push bulb into socket slightly,rotate anti-clockwise and remove.

4. Insert new bulb by slightlypressing and rotating.

5. Insert bulb holder in reflector andengage by turning clockwise.

6. Put on protective cover andengage wire clip.

Fog lightsThe bulbs are accessible from theunderside of the vehicle.

1. Turn the bulb holder anticlockwiseand remove it from the reflector.

2. Disengage the bulb holder fromthe plug connector by pressingthe retaining lug.

3. Remove and replace the bulbholder with bulb.

4. Attach the plug connector.5. Insert the bulb holder into the

reflector.6. Turn the bulb holder clockwise

and engage.

Vehicle care 157

Tail lights5-door passenger vehicle

1. Open side cover.When replacing bulbs on the righthand side, first remove the toolsand the jack or the tyre repair kit,then remove the tool box.

2. Remove plug connector bypressing on bulb holder tab.

3. Hold bulb housing from theoutside; unscrew two retainingnuts.

4. Detach bulb housing towards therear.

158 Vehicle care

5. Gently press the three lockinglugs on the outside of the bulbholder outwards and remove bulbholder.

6. Push bulb into socket slightly,rotate anti-clockwise, remove andrenew bulb.Rear fog light, may be only on oneside (1)Reverse light (2)Turn signal light (3)Tail light/side light (4)Tail light/brake light (5)

7. Engage bulb holder in bulbhousing, ensuring that it properlyengages.

8. Ensure that the bulb holder seal ispositioned as illustrated.

9. Insert bulb housing in vehiclebody, tighten securing nuts byhand. Engage plug connector.Close cover.

After bulb replacement, check the taillights for proper functionality: switchon the ignition, operate the brake,switch on the sidelights.

Vehicle care 159

3-door passenger vehicle, van

1. Open side cover.When replacing bulbs on the righthand side, first remove the toolsand the jack or the tyre repair kit,then remove the tool box.

2. Remove plug connector bypressing on bulb holder tab.

3. Hold bulb housing from theoutside; unscrew two retainingnuts.

4. Remove tail light assembly.

160 Vehicle care

5. Gently press the three lockinglugs on the outside of the bulbholder outwards and remove bulbholder.

6. Push bulb into socket slightly,rotate anti-clockwise, remove andrenew bulb.Reverse light (right side), rear foglight (left side) (1)Tail light (2)Turn signal light (3)Tail light/brake light (4)Tail light (5)

7. Engage bulb holder in bulbhousing, ensuring that it properlyengages.

8. Ensure that the bulb holder seal ispositioned as illustrated. Fit theround seal on the fastening bolt.

9. Insert bulb housing in vehiclebody, and tighten securing nuts byhand. Engage plug connector.Close and lock cover.

After bulb replacement, check the taillights for proper functionality: switchon the ignition, operate the brake,switch on the sidelights.

Side turn signal lightsTo replace bulb, remove lamphousing:

1. On left vehicle side, slide lamp tothe front and remove it out of thefront wing with the rear end.On right vehicle side, slide lamp tothe rear and remove it out of thefront wing with the front end.

Vehicle care 161

2. Turn bulb holder anticlockwiseand remove from housing.

3. Pull bulb from bulb holder andreplace it.

4. Insert bulb holder and turnclockwise.

5. On left side: insert front end intofront wing, slide forward and insertrear end.On right side: insert rear end intofront wing, slide rearward andinsert front end.

Number plate light

1. Insert screwdriver in bulbhousing, press to the side andrelease spring.

2. Remove bulb housingdownwards, taking care not to pullon the cable.

3. Lift flap and disconnect wiringplug from bulb holder.

162 Vehicle care

4. Rotate bulb holder anti-clockwiseto disengage.

5. Remove bulb from holder andrenew bulb.

6. Insert bulb holder in bulb housingand rotate clockwise.

7. Connect wiring plug to bulbholder.

8. Insert and engage bulb housing.

Interior lightsFront courtesy light

1. Disengage and remove lens at theposition located in the illustrationusing a screwdriver.

2. Remove bulb from socket.3. Insert new bulb.4. Mount lens and engage in

position.

Front courtesy light, readinglights

1. Disengage lens, press itdownward slightly and remove ata downward angle.

2. Remove bulb and renew.3. Engage lens.

Rear courtesy light and readinglightsHave bulbs replaced by a workshop.

Vehicle care 163

Glovebox light, foot well light

1. Prise the lamp out with ascrewdriver.

2. Press bulb slightly towards springclip and remove.

3. Insert new bulb.4. Install lamp.

Electrical systemFusesData on the replacement fuse mustmatch the data on the defective fuse.There are three fuse boxes in thevehicle:■ in the front left of the engine

compartment,■ in left-hand drive vehicles: in the

interior behind the light switch, or,in right-hand drive vehicles: behindthe glovebox,

■ behind a cover on the left side of theload compartment.

Before replacing a fuse, turn off therespective switch and the ignition.A blown fuse can be recognised by itsmelted wire. Do not replace the fuseuntil the cause of the fault has beenremedied.Some functions are protected byseveral fuses.Fuses may also be inserted withoutexistence of a function.

164 Vehicle care

Engine compartment fusebox

The fuse box is in the front left of theengine compartment.Disengage the cover, lift it upwardsand remove.

Vehicle care 165

No. Circuit

1 Starter

2 Air conditioning system

3 Diesel fuel filter heater

4 Horn

5 Manual transmission auto‐mated, automatic transmission

6 Engine control unit

7 Fog lights

8 Engine cooling

9 Engine cooling

10 Manual transmission auto‐mated

11 Glow plugs, ignition system

12 Headlight range adjustment,Adaptive forward lighting

13 Air conditioning system

14 Manual transmission auto‐mated

15 High beam (right)

No. Circuit

16 High beam (left)

17 Main relay

18 Engine control unit

19 Airbags

20 Main relay

21 Main relay

22 Central control unit

23 Tyre repair kit

24 Fuel pump

25 ABS

26 Heated rear window

27 ABS

28 Interior fan

29 Cigarette lighter

30 Air conditioning system

31 Power window (left)

32 Power window (right)

No. Circuit

33 Heated exterior mirrors

34 –

35 –

Instrument panel fuse box

In left-hand drive vehicles, the fusebox is behind the light switch. Pull thetop edge of the panel and fold down.

166 Vehicle care

In right-hand drive vehicles, the fusebox is located behind a cover in theglovebox. Open the glovebox andremove the cover. To close, first puton the cover, then lock it into position.

No. Circuit

1 –

2 Instruments, info-display

3 Radio

4 Ignition switch

5 Windscreen washer system

6 Central locking system, tailgate

7 Central locking system

8 –

9 Courtesy light

No. Circuit

10 Electrical power steering

11 Light switch, brake light

12 ABS, brake light

13 Heated steering wheel

14 Park assist, rain sensor, interiormirror

Load compartment fusebox

Vehicle care 167

The fuse box is on the left side of theload compartment behind a cover.Remove the cover.

No. Circuit

1 Adaptive forward lighting

2 –

3 Seat heater (left)

4 Seat heater (right)

5 –

6 –

No. Circuit

7 –

8 Rear carrier system, towingequipment

9 –

10 –

11 –

12 –

13 –

14 –

15 Rear carrier system, towingequipment

16 –

17 Sunroof

Vehicle toolsTools

To open the compartment, disengagethe cover and open it.

168 Vehicle care

Vehicles with spare wheel

Variant 1: The jack and the vehicletools are in the load compartmentunderneath the spare wheel. A labelon the jack indicates the vehicles forwhich the jack can be used.

Variant 2: The jack and the vehicletools are in the right-handcompartment in the loadcompartment.

Vehicles with tyre repair kit

The vehicle tools are in the right-handcompartment in the loadcompartment, together with the tyrerepair kit.

Vehicle care 169

Wheels and tyres

Tyre condition, wheel conditionDrive over edges slowly and at rightangles if possible. Driving over sharpedges can cause tyre and wheeldamage. Do not trap tyres on the kerbwhen parking.Regularly check the wheels fordamage. Seek the assistance of aworkshop in the event of damage orunusual wear.

TyresTyres of size 185/60 R 15 are onlyapproved as winter tyres.Tyres of size 185/65 R 15 are onlyapproved as winter tyres on vehicleswith a sports chassis. We recommendthat you contact a workshop in orderto find out whether your vehicle isequipped with a sports chassis.

Winter tyresWinter tyres improve driving safety attemperatures below 7 °C and shouldtherefore be fitted on all wheels.Tyres of size 185/60 R 15,185/65 R 15, 185/70 R 14,195/55 R 16 and205/50 R 16 are permitted as wintertyres.Tyres of size 195/60 R 15,215/45 R 171) and 225/35 R 18 mustnot be used as winter tyres.Run-flat winter tyres may only beused on factory approved alloywheels.In accordance with country-specificregulations, affix the speed sticker inthe driver's field of view.

Tyre designationsE.g. 185/65 R 15 88 T185 = Tyre width, mm65 = Cross-section ratio (tyre

height to tyre width), %R = Belt type: Radial

RF = Type: RunFlat15 = Wheel diameter, inches88 = Load index e.g. 88 is

equivalent to 567 kgT = Speed code letter

Speed code letter:Q = up to 100 mphS = up to 112 mphT = up to 118 mphH = up to 130 mphV = up to 150 mphW = up to 168 mph

Tyre pressureCheck the pressure of cold tyres atleast every 14 days and before anylong journey. Do not forget the sparewheel. This also applies to vehicleswith tyre deflation detection system.Remove the valve cap key from thefuel filler flap and use it to unscrew thevalve cap.

1) Corsa VXR: Permitted as winter tyres without tyre chains.

170 Vehicle care

Tyre pressure 3 212 and on the labelon the inside of the fuel filler flap or onthe front right door frame.The tyre pressure data refers to coldtyres. It applies to summer and wintertyres.Always inflate the spare tyre to thepressure specified for full load.The ECO tyre pressure serves toachieve the smallest amount of fuelconsumption possible.Incorrect tyre pressures will impairsafety, vehicle handling, comfort andfuel economy and will increase tyrewear.

9 Warning

If the pressure is too low, this canresult in considerable tyre warm-up and internal damage, leading totread separation and even to tyreblow-out at high speeds.

Tyre deflation detectionsystemThe tyre deflation detection systemcontinually checks the rotation speedof all four tyres.If a tyre loses pressure the controlindicator w illuminates red. Stopimmediately and check tyre pressure.Control indicator w 3 81.

System initialisation

After tyre pressure correction orwheel change, the system must beinitiated: Switch on the ignition, pressand hold the DDS button for approx.4 seconds, control indicator w flashesthree times.

Tread depthCheck tread depth at regularintervals.Tyres should be replaced for safetyreasons at a tread depth of 2-3 mm(4 mm for winter tyres).

Vehicle care 171

For safety reasons it is recommendedthat the tread depth of the wheels onone axle should not vary by more than2 mm.

The legally permissible minimumtread depth (1.6 mm) has beenreached when the tread has worndown as far as one of the tread wearindicators (TWI). Their position isindicated by markings on thesidewall.If there is more wear at the front thanthe rear, swap round front wheels andrear wheels periodically. Ensure thatthe direction of rotation of the wheelsremains the same.

Tyres age, even if they are not used.We recommend tyre replacementevery 6 years.

Changing tyre and wheelsizeIf tyres of a different size than thosefitted at the factory are used, it may benecessary to reprogramme thespeedometer and make other vehiclemodifications.After converting to a different tyresize, have the label with tyrepressures replaced.

9 Warning

Use of unsuitable tyres or wheelsmay lead to accidents and willinvalidate the vehicle typeapproval.

Wheel coversWheel covers and tyres that arefactory approved for the respectivevehicle and comply with all of therelevant wheel and tyre combinationrequirements must be used.If the wheel covers and tyres used arenot factory approved, the tyres mustnot have a rim protection ridge.Wheel covers must not impair brakecooling.

9 Warning

Use of unsuitable tyres or wheelcovers could lead to suddenpressure loss and therebyaccidents.

172 Vehicle care

Tyre chains

Tyre chains are only permitted on thefront wheels.Always use fine mesh chains that addno more than 10 mm to the tyre treadand the inboard sides (including chainlock).

9 Warning

Damage may lead to tyre blowout.

Tyre chains are only permitted on tyresizes 175/70 R 14, 185/60 R 15,185/65 R 152), 185/70 R 14,195/55 R 162) and 205/50 R16.Tyre chains are only approved ontyres of size 185/60 R 15 on vehicleswith a sports chassis. We recommendthat you contact a workshop in orderto find out whether your vehicle isequipped with a sports chassis.Tyre chains are not permitted on tyresizes 195/60 R 15, 215/45 R 17 and225/35 R18.The use of tyre chains is not permittedon the temporary spare wheel.

Tyre repair kitMinor damage to the tyre tread can berepaired with the tyre repair kit.Do not remove foreign bodies fromthe tyres.Tyre damage exceeding 4 mm or thatis at the tyre's side wall near the rimcannot be repaired with the tyre repairkit.

9 Warning

Do not drive faster than 50 mph.Do not use for a lengthy period.Steering and handling may beaffected.

If you have a flat tyre:Apply the parking brake and engagefirst gear, reverse gear or P.

The tyre repair kit is in the stowagecompartment in the loadcompartment.

2) Not permitted when used as winter tyres.

Vehicle care 173

To open the compartment, disengagethe cover and open it.

1. Take the sealant bottle andbracket with air hose from theinsert.

2. Detach air hose from bracket andscrew onto sealant bottleconnection.

3. Position the sealant bottle on thebracket. Make sure that the bottledoes not fall.

4. Unscrew valve cap from defectivetyre.

5. Screw tyre inflation hose to valve.6. Screw air hose onto compressor

connection.7. Switch on ignition.

To avoid discharging the battery,we recommend running theengine.

174 Vehicle care

8. Press on/off switch on thecompressor. The tyre is filled withsealant.

9. The compressor pressure gaugebriefly indicates up to 6 bar whilstthe sealant bottle is emptying(approx. 30 seconds). Then thepressure starts to drop.

10. All of the sealant is pumped intothe tyre. Then the tyre is inflated.

11. The prescribed tyre pressureshould be obtained within10 minutes. Tyre pressure3 212. When the correct pressureis obtained, switch off the

compressor by pressing the on/offswitch again.If the prescribed tyre pressure isnot obtained within 10 minutes,remove the tyre repair kit. Movethe vehicle one tyre rotation.Reattach the tyre repair kit andcontinue the filling procedure for10 minutes. If the prescribed tyrepressure is still not obtained, thetyre is too badly damaged. Seekthe assistance of a workshop.Release excess tyre pressureusing the ] button.Do not run the compressor forlonger than 10 minutes.

12. Push catch on bracket to removesealant bottle from bracket. Screwthe tyre inflation hose to the freeconnection of the sealant bottle.This prevents sealant fromescaping. Stow tyre repair kit inload compartment.

13. Remove any excess sealantusing a cloth.

14. Take the label indicatingmaximum permitted speed fromthe sealant bottle and affix in thedriver's field of view.

15. Continue driving immediately sothat sealant is evenly distributedin the tyre. After driving approx.6 miles (but no more than10 minutes), stop and check tyrepressure. Screw compressor airhose directly onto tyre valve andcompressor when doing this.If tyre pressure is more than1.3 bar, set it to the correct value.Repeat the procedure until thereis no more loss of pressure.If the tyre pressure has fallenbelow 1.3 bar, the vehicle mustnot be used. Seek the assistanceof a workshop.

16. Stow away tyre repair kit in loadcompartment.

Vehicle care 175

NoteThe driving characteristics of therepaired tyre are severely affected,therefore have this tyre replaced.If unusual noise is heard or thecompressor becomes hot, turncompressor off for at least30 minutes.The built-in safety valve opens at apressure of 7 bar (102 psi).Note the expiry date of the kit. Afterthis date its sealing capability is nolonger guaranteed. Pay attention tostorage information on sealantbottle.Replace the used sealant bottle.Dispose of the bottle as prescribedby applicable laws.The compressor and sealant can beused from approx. -30 °C.The adapters supplied can be usedto pump up other items e.g.footballs, air mattresses, inflatabledinghies etc. They are located on theunderside of the compressor. Toremove, screw on compressor airhose and withdraw adapter.

Wheel changingSome vehicles are equipped with atyre repair kit instead of a spare wheel3 172.Make the following preparations andobserve the following information:■ Park the vehicle on a level, firm and

non-skid surface. The front wheelsmust be in the straight-aheadposition.

■ Apply the parking brake andengage first gear, reverse gear orP.

■ Remove the spare wheel 3 177.■ Never change more than one wheel

at a time.■ Use the jack only to change wheels

in case of puncture, not forseasonal winter or summer tyrechange.

■ If the ground on which the vehicleis standing is soft, a solid board(max. 1 cm thick) should be placedunder the jack.

■ No people or animals may be in thevehicle when it is jacked-up.

■ Never crawl under a jacked-upvehicle.

■ Do not start the vehicle when it israised on the jack.

■ Before screwing in the wheel bolts,clean them and lightly coat thetaper of each wheel bolt withcommercially available grease.

1. Pull off the wheel cover with thehook. Vehicle tools 3 167.For wheel covers with visiblewheel bolts: The cover can remainon the wheel. Do not remove theretaining rings on the wheel bolts.

176 Vehicle care

Alloy wheels: Disengage wheelbolt caps with a suitablescrewdriver and remove. Toprotect the wheel, place a softcloth between the screwdriverand the alloy wheel.

2. Install the wheel wrench ensuringthat it locates securely andslacken each bolt by half a turn.

3. Ensure the jack is positionedcorrectly with the vehicle jackingpoints.With versions of the Corsa VXRwith sill panelling or retrofitted sillpanelling, no jack must be used.The vehicle may be damaged.

4. Set the jack to the necessaryheight. Position it directly belowthe jacking point in a manner thatprevents it from slipping.Variant 1:

Vehicle care 177

Variant 2:

Attach jack handle and with thejack correctly aligned rotatehandle until wheel is clear of theground.

5. Unscrew the wheel bolts.6. Change the wheel.7. Screw in the wheel bolts.8. Lower vehicle.9. Install the wheel wrench ensuring

that it locates securely and tighteneach bolt in a crosswisesequence. Tightening torque is110 Nm.

10. Align the valve hole in the wheelcover with the tyre valve beforeinstalling.Install wheel bolt caps.

11. Stow the replaced wheel 3 172and the vehicle tools 3 167.

12. Check the tyre pressure of theinstalled tyre and also the wheelbolt torque as soon as possible.

Have the defective tyre renewed orrepaired.

Spare wheelSome vehicles are equipped with atyre repair kit instead of a sparewheel.

The spare wheel can be classified asa temporary spare wheel dependingon the size compared to the othermounted wheels and countryregulations.The spare wheel has a steel rim.Use of a spare wheel that is smallerthan the other wheels or together withwinter tyres could affect driveability.Have the defective tyre replaced assoon as possible.

The spare wheel is located in the loadcompartment beneath the floorcovering. It is secured with a wing nut.

178 Vehicle care

In the Corsa van the spare wheel isscrewed down together with the floorcover. To lift the cover, undo theplastic nut. There is a spacer betweenthe spare wheel and the floor cover.The spare wheel well is not designedfor all permitted tyre sizes. If a wheelwider than the spare must be stowedin the spare wheel well after changingwheels, the floor cover will be restingagainst the protruding wheel. In vansthe spacer can be omitted ifnecessary, or the wheel can be bolteddown without the floor cover.Fitting a double load-bay floor in thiscase in the upper position 3 64.To remove, lift spare wheel, move toa vertical position and remove fromabove.

Temporary spare wheelUse of the temporary spare wheelcould affect driveability. Have thedefective tyre renewed or repaired assoon as possible.

Only mount one temporary sparewheel. Do not drive faster than50 mph. Take curves slowly. Do notuse for a long period of time.If your vehicle gets a flat tyre on therear while towing another vehicle,mount the temporary spare wheel inthe front and the full tyre in the rear.Tyre chains 3 172.

Directional tyresFit directional tyres such that they rollin the direction of travel. The rollingdirection is indicated by a symbol(e.g. an arrow) on the sidewall.The following applies to tyres fittedopposing the rolling direction:■ Driveability may be affected. Have

the defective tyre renewed orrepaired as soon as possible.

■ Drive particularly carefully on wetand snow-covered road surfaces.

Jump startingDo not start with quick charger.A vehicle with a discharged batterycan be started using jump leads andthe battery of another vehicle.

9 Warning

Be extremely careful when startingwith jump leads. Any deviationfrom the following instructions canlead to injuries or damage causedby battery explosion or damage tothe electrical systems of bothvehicles.

9 Warning

Avoid contact of the battery witheyes, skin, fabrics and paintedsurfaces. The fluid containssulphuric acid which can causeinjuries and damage in the eventof direct contact.

Vehicle care 179

NoteAny deviation from the instructionsgiven in this paragraph may lead toa temporary deactivation of the stop-start system.

■ Never expose the battery to nakedflames or sparks.

■ A discharged battery can alreadyfreeze at temperatures of 0 °C.Defrost the frozen battery beforeconnecting jump leads.

■ Avoid contact with eyes, skin,fabrics and painted surfaces. Thefluid contains sulphuric acid whichcan cause injuries and damage inthe event of direct contact.

■ Wear eye protection and protectiveclothing when handling a battery.

■ Use a booster battery with thesame voltage (12 Volts). Itscapacity (Ah) must not be muchless than that of the dischargedbattery.

■ Use jump leads with insulatedterminals and a cross section of atleast 16 mm2 (25 mm2 for dieselengines).

■ Do not disconnect the dischargedbattery from the vehicle.

■ Switch off all unnecessary electricalconsumers.

■ Do not lean over the battery duringjump starting.

■ Do not allow the terminals of onelead to touch those of the otherlead.

■ The vehicles must not come intocontact with each other during thejump starting process.

■ Apply the parking brake,transmission in neutral, automatictransmission in P.

Lead connection order:1. Connect the red lead to the

positive terminal of the boosterbattery.

2. Connect the other end of the redlead to the positive terminal of thedischarged battery. The positiveterminal has a cover cap on it.Undo the cap to access thepositive terminal.

3. Connect the black lead to thenegative terminal of the boosterbattery.

4. Connect the other end of the blacklead to a vehicle grounding point,such as the engine block or anengine mounting bolt. Connect asfar away from the dischargedbattery as possible, however atleast 60 cm.

180 Vehicle care

Position the leads so that they cannotcatch on rotating parts in the enginecompartment.To start the engine:1. Start the engine of the vehicle

providing the jump.2. After 5 minutes, start the other

engine. Start attempts should bemade for no longer than15 seconds at an interval of1 minute.

3. Allow both engines to idle forapprox. 3 minutes with the leadsconnected.

4. Switch on electrical consumers(e.g. headlights, heated rearwindow) of the vehicle receivingthe jump start.

5. Reverse above sequence exactlywhen removing leads.

6. Close the cover over the positivepole.

TowingTowing the vehicle

Insert a suitable screwdriver in theslot at the lower bend of the cap.Release the cap by carefully movingthe screwdriver downwards.Corsa VXR: Disengage and removecap by pressing on the lower part ofthe cap.

Vehicle care 181

The towing eye is stowed with thevehicle tools 3 167. The towing eye islocated in a recess.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.Attach a tow rope – or better still a towrod – to the towing eye.The towing eye must only be used fortowing and not recovering the vehicle.Switch on ignition to release steeringwheel lock and to permit operation ofbrake lights, horn and windscreenwiper.Transmission in neutral.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

When the engine is not running,considerably more force is needed tobrake and steer.To prevent the entry of exhaust gasesfrom the towing vehicle, switch on theair recirculation and close thewindows.

Vehicles with automatic transmissionmust be towed facing forwards, notfaster than 50 mph nor further than60 miles. In all other cases and whenthe transmission is defective, the frontaxle must be raised off the ground.Seek the assistance of a workshop.Manual transmission automated3 121.After towing, unscrew the towing eyeand refit the cover.

Towing another vehicle

Disengage cap at bottom and removedownwards.

182 Vehicle care

The towing eye is stowed with thevehicle tools 3 167.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.The lashing eye at the rearunderneath the vehicle must never beused as a towing eye.Attach a tow rope – or better still a towrod – to the towing eye.The towing eye must only be used fortowing and not recovering a vehicle.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

After towing, unscrew the towing eyeand refit the cover.

Appearance careExterior careLocksThe locks are lubricated at the factoryusing a high quality lock cylindergrease. Use de-icing agent only whenabsolutely necessary, as this has adegreasing effect and impairs lockfunction. After using de-icing agent,have the locks regreased by aworkshop.

WashingThe paintwork of your vehicle isexposed to environmental influences.Wash and wax your vehicle regularly.When using automatic car washes,select a programme that includeswaxing.Bird droppings, dead insects, resin,pollen and the like should be cleanedoff immediately, as they containaggressive constituents which cancause paint damage.

Vehicle care 183

If using a car wash, comply with thecar wash manufacturer's instructions.The windscreen wipers and rearwindow wiper must be switched off.Remove antenna and externalaccessories such as roof racks etc.If you wash your vehicle by hand,make sure that the insides of thewheel housings are also thoroughlyrinsed out.Clean edges and folds on openeddoors and the bonnet as well as theareas they cover.

Caution

Always use a cleaning agent witha pH value of 4 to 9.Do not use cleaning agents on hotsurfaces.

Have the door hinges of all doorsgreased by a workshop.Do not clean the engine compartmentwith a steam-jet or high-pressure jetcleaner.

Thoroughly rinse and leather-off thevehicle. Rinse leather frequently. Useseparate leathers for painted andglass surfaces: remnants of wax onthe windows will impair vision.

Exterior lightsHeadlight and other light covers aremade of plastic. Do not use anyabrasive or caustic agents, do not usean ice scraper, and do not clean themdry.

Polishing and waxingWax the vehicle regularly (at thelatest when water no longer beads).Otherwise, the paintwork will dry out.Polishing is necessary only if the painthas become dull or if solid depositshave become attached to it.Paintwork polish with silicone forms aprotective film, making waxingunnecessary.Plastic body parts must not be treatedwith wax or polishing agents.

Windows and windscreen wiperbladesUse a soft lint-free cloth or chamoisleather together with window cleanerand insect remover.When cleaning the rear window,make sure the heating element insideis not damaged.For mechanical removal of ice, use asharp-edged ice scraper. Press thescraper firmly against the glass sothat no dirt can get under it andscratch the glass.Clean smearing wiper blades with asoft cloth and window cleaner.

SunroofNever clean with solvents or abrasiveagents, fuels, aggressive media (e.g.paint cleaner, acetone-containingsolutions etc.), acidic or highlyalkaline media or abrasive pads. Donot apply wax or polishing agents tothe sunroof.

Wheels and tyresDo not use high-pressure jetcleaners.

184 Vehicle care

Clean rims with a pH-neutral wheelcleaner.Rims are painted and can be treatedwith the same agents as the body.

Paintwork damageRectify minor paintwork damage witha touch-up pen before rust forms.Have more extensive damage or rustareas repaired by a workshop.

UnderbodySome areas of the vehicle underbodyhave a PVC undercoating while othercritical areas have a durableprotective wax coating.After the underbody is washed, checkthe underbody and have it waxed ifnecessary.Bitumen/rubber materials coulddamage the PVC coating. Haveunderbody work carried out by aworkshop.Before and after winter, wash theunderbody and have the protectivewax coating checked.

Liquid gas system

9 Danger

Liquid gas is heavier than air andcan collect in sink points.Take care when performing workat the underbody in a pit.

For painting work and when using adrying booth at a temperature above60 °C, the liquid gas tank must beremoved.Do not make any modifications to theliquid gas system.

Towing equipmentDo not clean the coupling ball bar witha steam-jet or high-pressure jetcleaner.

Rear carrier systemClean the rear carrier system with asteam-jet or high-pressure jet cleanerat least once a year.Operate the rear carrier systemperiodically if not in regular use, inparticular during winter.

Interior careInterior and upholsteryOnly clean the vehicle interior,including the instrument panel fasciaand panelling, with a dry cloth orinterior cleaner.Clean the leather upholstery withclear water and a soft cloth. In case ofheavy soiling, use leather care.The instrument cluster and thedisplays should only be cleaned usinga soft damp cloth.Clean fabric upholstery with avacuum cleaner and brush. Removestains with an upholstery cleaner.Clothing fabrics may not becolourfast. This could cause visiblediscolourations, especially on light-coloured upholstery. Removablestains and discolourations should becleaned as soon as possible.Clean seat belts with lukewarm wateror interior cleaner.

Vehicle care 185

Caution

Close Velcro fasteners as openVelcro fasteners on clothing coulddamage seat upholstery.The same applies to clothing withsharp-edged objects, like zips orbelts or studded jeans.

Plastic and rubber partsPlastic and rubber parts can becleaned with the same cleaner asused to clean the body. Use interiorcleaner if necessary. Do not use anyother agent. Avoid solvents and petrolin particular. Do not use high-pressure jet cleaners.

186 Service and maintenance

Service andmaintenance

General information ................... 186Recommended fluids, lubricantsand parts .................................... 187

General informationService informationIn order to ensure economical andsafe vehicle operation and tomaintain the value of your vehicle, itis of vital importance that allmaintenance work is carried out at theproper intervals as specified.The detailed, up-to-date serviceschedule for your vehicle is availableat the workshop.

European service intervalsService is due every 20000 miles or1 year, whichever occurs first.The European schedule is valid forthe following countries:Andorra, Austria, Belgium, Bosnia-Herzegovina, Bulgaria, Croatia,Cyprus, Czech Republic, Denmark,Estonia, Finland, France, Germany,Greece, Greenland, Hungary,Iceland, Ireland, Italy, Latvia,Lithuania, Luxembourg, Macedonia,Malta, Montenegro, Netherlands,

Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden,Switzerland, United Kingdom.

International service intervalsService is due every 10000 miles or1 year, whichever occurs first.The international service intervals arevalid for the countries which are notlisted in the European serviceintervals.

ConfirmationsConfirmation of service is recorded inthe Service and Warranty Booklet.The date and mileage is completedwith the stamp and signature of theservicing workshop.Make sure that the Service andWarranty Booklet is completedcorrectly as continuous proof ofservice is essential if any warranty orgoodwill claims are to be met, and isalso a benefit when selling thevehicle.

Service and maintenance 187

Fixed service intervalWhen service is due, InSP appears inthe odometer display for approx.10 seconds when the ignition isswitched on. Have the next serviceperformed by a workshop withinone week or 300 miles (whicheveroccurs first).

Flexible service intervalThe service interval is based onseveral parameters depending onusage and calculated using theseparameters.If the remaining distance is less than1000 miles, InSP is displayed with aremaining distance of 600 miles whenthe ignition is switched on and off. Ifless than 600 miles remain, InSP isdisplayed for several seconds. Havethe next service performed by aworkshop within one week or300 miles (whichever occurs first).

Display of remaining distance:1. Switch off ignition.2. Briefly press the trip odometer

reset button. The odometerreading is shown.

3. Press and hold the reset button forapprox. 2 seconds. InSP and theremaining distance are displayed.

Recommended fluids,lubricants and partsRecommended fluids andlubricantsOnly use products that have beentested and approved. Damageresulting from the use of non-approved materials will not becovered by the warranty.

9 Warning

Operating materials arehazardous and could bepoisonous. Handle with care. Payattention to information given onthe containers.

Engine oilEngine oil is identified by its qualityand its viscosity. Quality is moreimportant than viscosity whenselecting which engine oil to use. Theoil quality ensures e.g. enginecleanliness, wear protection and oil

188 Service and maintenance

aging control, whereas viscositygrade gives information on the oil'sthickness over a temperature range.Dexos is the newest engine oil qualitythat provides optimum protection forgasoline and diesel engines. If it isunavailable, engine oils of other listedqualities have to be used.Recommendations for gasolineengines are also valid forCompressed Natural Gas (CNG),Liquified Petroleum Gas (LPG) andEthanol (E85) fuelled engines.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 192.

Topping up engine oilEngine oils of different manufacturersand brands can be mixed as long asthey comply with the required engineoil quality and viscosity.Use of engine oil with onlyACEA A1/B1 or only A5/B5 quality isprohibited, since it can cause long-term engine damage under certainoperating conditions.

Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 192.

Additional engine oil additivesThe use of additional engine oiladditives could cause damage andinvalidate the warranty.

Engine oil viscosity gradesThe SAE viscosity grade givesinformation of the thickness of the oil.Multigrade oil is indicated by twofigures, e.g. SAE 5W-30. The firstfigure, followed by a W, indicates thelow temperature viscosity and thesecond figure the high temperatureviscosity.Select the appropriate viscosity gradedepending on the minimum ambienttemperature 3 192.All of the recommended viscositygrades are suitable for high ambienttemperatures.

Coolant and antifreezeUse only silicate-free long life coolant(LLC) antifreeze.The system is factory filled withcoolant designed for excellentcorrosion protection and frostprotection down to approx. -28 °C.This concentration should bemaintained all year round. The use ofadditional coolant additives thatintend to give additional corrosionprotection or seal against minor leakscan cause function problems. Liabilityfor consequences resulting from theuse of additional coolant additives willbe rejected.

Brake and clutch fluidOnly use high-performance brakefluid approved for the vehicle, consulta workshop.Over time, brake fluid absorbsmoisture which will reduce brakingeffectiveness. The brake fluid shouldtherefore be replaced at the specifiedinterval.

Service and maintenance 189

Brake fluid should be stored in asealed container to avoid waterabsorption.Ensure brake fluid does not becomecontaminated.

190 Technical data

Technical data

Vehicle identification .................. 190Vehicle data ............................... 192

Vehicle identificationVehicle IdentificationNumber

The Vehicle Identification Number isstamped on the identification plateand on the floor pan, under the floorcovering, visible under a cover.The Vehicle Identification Numbermay be embossed on the instrumentpanel visible through the windscreen.

Identification plate

The identification plate is located onthe front right door frame.

Technical data 191

Information on identification plate:1 = Manufacturer2 = Type approval number3 = Vehicle Identification Number4 = Permissible gross vehicle

weight rating in kg5 = Permissible gross train weight

in kg6 = Maximum permissible front axle

load in kg7 = Maximum permissible rear axle

load in kg8 = Vehicle-specific or country

specific data

The combined total of front and rearaxle loads must not exceed thepermissible gross vehicle weight. Forexample, if the front axle is bearing itsmaximum permissible load, the rearaxle can only bear a load that is equalto the gross vehicle weight minus thefront axle load.The technical data is determined inaccordance with EuropeanCommunity standards. We reservethe right to make modifications.

Specifications in the vehicledocuments always have priority overthose given in this manual.

192 Technical data

Vehicle dataRecommended fluids and lubricantsEuropean service schedule

Required engine oil qualityAll European countries

(except Belarus, Moldova, Russia, Serbia, Turkey) Only Israel

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

dexos 1 – – ✔ –

dexos 2 ✔ ✔ – ✔

In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.

Engine oil viscosity gradesAll European countries and Israel(except Belarus, Moldova, Russia, Serbia, Turkey)

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

Technical data 193

International service schedule

Required engine oil qualityAll countries outside Europe

except Israel Only Belarus, Moldova, Russia, Serbia, Turkey

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

dexos 1 ✔ – – –

dexos 2 – ✔ ✔ ✔

In case dexos quality is unavailable you may use the oil qualities listed below:

All countries outside Europeexcept Israel Only Belarus, Moldova, Russia, Serbia, Turkey

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

GM-LL-A-025 ✔ – ✔ –

GM-LL-B-025 – ✔ – ✔

194 Technical data

All countries outside Europeexcept Israel Only Belarus, Moldova, Russia, Serbia, Turkey

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

ACEA A3/B3 ✔ – ✔ –

ACEA A3/B4 ✔ ✔ ✔ ✔

ACEA C3 ✔ ✔ ✔ ✔

API SM ✔ – ✔ –

API SN resource conserving ✔ – ✔ –

Engine oil viscosity gradesAll countries outside Europe (except Israel),including Belarus, Moldova, Russia, Serbia, Turkey

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

down to -20 °C SAE 10W-301) or SAE 10W-401)

1) Permitted, but usage of SAE 5W-30 or SAE 5W-40 with dexos quality is recommended.

Technical data 195

Engine dataSales designation 1.0 1.2 1.2 1.4Engine identifier code A10XEP A12XEL A12XER A14XEL

Piston displacement [cm3] 998 1229 1229 1398

Engine power [kW] 48 51 632) 64

at rpm 5300 5600 5600 6000

Torque [Nm] 90 115 1153) 130

at rpm 4000 4000 4000 4000

Fuel type Petrol Petrol Petrol/LPG Petrol

Octane rating RON

recommended 95 95 95 95

possible 98 98 98 98

possible 91 91 91 91

Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6

2) 61 with LPG engine.3) 110 with LPG engine.

196 Technical data

Sales designation 1.4 1.4 1.6 VXR 1.6 VXR Nürburgring EditionEngine identifier code A14XER A14NEL A16LER A16LES

Piston displacement [cm3] 1398 1364 1598 1598

Engine power [kW] 74 88 141 155

at rpm 6000 4800-6000 5850 5850

Torque [Nm] 130 175 230 250

at rpm 4000 1750-4800 1980-5850 2250-5850

Fuel type Petrol Petrol Petrol Petrol

Octane rating RON

recommended 95 95 98 100

possible 98 98 95 98

possible 91 – – –

Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6

Technical data 197

Sales designation 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.3 CDTI 1.7 CDTIEngine identifier code Z13DTJ A13DTE Eco A13DTC A13DTR A17DTS

Piston displacement [cm3] 1248 1248 1248 1248 1686

Engine power [kW] 55 70 55 70 96

at rpm 4000 4000 4000 4000 4000

Torque [Nm] 170 190 190 210 300

at rpm 1750-2500 1750-3250 1750-2250 1750-2500 2000-2500

Fuel type Diesel Diesel Diesel Diesel Diesel

Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6 0.6

198 Technical data

Performance5-door vehicleEngine A10XEP A12XEL A12XER A14XEL A14XER A14NEL

Maximum speed4) [mph]

Manual transmission 96 99 1075)6) 108 112 121

Manual transmission automated – – 107 – – –

Automatic transmission – – – – 107 –

Engine Z13DTJ A13DTC A13DTR A13DTE Eco A17DTS

Maximum speed4) [mph]

Manual transmission 101 101 108 110 124

Manual transmission automated – – – – –

Automatic transmission – – – – –

4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipmentcould reduce the specified maximum speed of the vehicle.

5) LPG engine in petrol mode: 106.6) LPG engine in LPG mode: 104.

Technical data 199

3-door vehicleEngine A10XEP A12XEL A12XER A14XEL A14XER

Maximum speed4) [mph]

Manual transmission 96 99 1075)6) 108 112

Manual transmission automated – – 107 – –

Automatic transmission – – – – 107

Engine A14NEL A16LER A16LES A13DTE Eco

Maximum speed 4) [mph]

Manual transmission 121 140 143 110

Manual transmission automated – – – –

Automatic transmission – – – –

4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipmentcould reduce the specified maximum speed of the vehicle.

5) LPG engine in petrol mode: 106.6) LPG engine in LPG mode: 104.

200 Technical data

Engine A13DTC A13DTR A17DTS

Maximum speed4) [mph]

Manual transmission 101 108 124

Manual transmission automated – – –

Automatic transmission – – –

VanEngine A10XEP A12XEL A12XER

Maximum speed 4) [mph]

Manual transmission 96 99 107

Manual transmission automated – – 107

Automatic transmission – – –

4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipmentcould reduce the specified maximum speed of the vehicle.

Technical data 201

Engine Z13DTJ A13DTC A13DTE Eco A13DTR

Maximum speed4) [mph]

Manual transmission 101 101 110 108

Manual transmission automated – – – –

Automatic transmission – – – –

4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipmentcould reduce the specified maximum speed of the vehicle.

202 Technical data

Vehicle weightKerb weight, 5-door vehicle, basic model without any optional equipmentCorsa Engine Manual

transmissionManualtransmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A10XEP 1145/1165 – –

A12XEL 1163/1178 – –

A12XER 11637)/11787) – –

A14XEL 1163/1178 – 1188/1208

A14XER 1163/1178 – –

A14NEL 1237/1252 – –

A13DTC 1235/1255 – –

Z13DTJ 1235/1255 – –

without/with air conditioning or electronic climatecontrol[kg]

A13DTEECO

1199/1209 1199/1209 –

7) With LPG engine, weight increased by 36 kg.

Technical data 203

Corsa Engine Manualtransmission

Manualtransmissionautomated

Automatictransmission

A13DTR 1265/1285 1265/1285 –

A17DTS 1320/1340 – –

Kerb weight, 5-door vehicle, basic model with all optional equipmentCorsa Engine Manual

transmissionManualtransmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A10XEP –/1280 – –

A12XEL –/1278 – –

A12XER –/12788) – –

A14XEL –/12789) – –/1317

A14XER –/12789) – –

A14NEL –/1361 – –

A13DTC –/1365 – –

Z13DTJ –/1365 – –

8) With LPG engine, weight increased by 40 kg.9) With rear carrier system, weight increased by 40 kg.

204 Technical data

Corsa Engine Manualtransmission

Manualtransmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A13DTEECO

–/1318 –/1318 –

A13DTR –/1396 –/1396 –

A17DTS –/1424 – –

Technical data 205

Kerb weight, 3-door vehicle, basic model without any optional equipmentCorsa Engine Manual

transmissionManualtransmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A10XEP 1100/1120 – –

A12XEL 1120/1135 – –

A12XER 112010)/113510) – –

A14XEL 1141/1156 – –

A14XER 1141/1156 – 1165/1185

A14NEL 1199/1214 – –

A16LER 1278/1293 – –

A16LES 1278/1293 – –

A13DTC 116311)/117312) – –

10) With LPG engine, weight increased by 43 kg.11) With stop-start system, weight increased by 42 kg.12) With stop-start system, weight increased by 52 kg.

206 Technical data

Corsa Engine Manualtransmission

Manualtransmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A13DTEECO

1163/1173 1163/1173 –

A13DTR 1235/1255 1235/1255 –

A17DTS 1278/1298 – –

Technical data 207

Kerb weight, 3-door vehicle, basic model with all optional equipmentCorsa Engine Manual

transmissionManualtransmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A10XEP –/1235 – –

A12XEL –/1259 – –

A12XER –/125913) – –

A14XEL –/1278 – –

A14XER –/1278 – –/1299

A14NEL –/1318 – –

A16LER –/1318 – –

A16LES –/1318 – –

A13DTC –/131814) – –

without/with air conditioning or electronic climatecontrol[kg]

A13DTEECO

–/1278 –/1278 –

A13DTR –/1371 –/1371 –

A17DTS –/1387 – –

13) With LPG engine, weight increased by 19 kg.14) With stop-start system, weight increased by 21 kg.

208 Technical data

Kerb weight, van, basic model without any optional equipmentCorsa Engine Manual transmission Manual

transmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A10XEP 1125/1145 – –

A12XEL 114015)/116015) – –

A12XER 114015)/116015) 114015)/116015) –

Z13DTJ 121515)/123515) – –

A13DTC 121515)/123515) – –

A13DTR 124515)/126515) – –

15) In conjunction with 17 inch wheels, weight increased by 20 kg.

Technical data 209

Kerb weight, van, basic model with all optional equipmentCorsa Engine Manual transmission Manual

transmissionautomated

Automatictransmission

without/with air conditioning or electronic climatecontrol[kg]

A10XEP –/1230 – –

A12XEL –/124516) – –

A12XER –/124516) –/124516) –

Z13DTJ –/132016) – –

A13DTC –/132016) – –

A13DTR –/135016) – –

Vehicle dimensions5-door vehicle 3-door vehicle VXR Van

Length [mm] 3999 3999 4040 3999

Width without exterior mirrors [mm] 1737 1713 1713 1713

Width with two exterior mirrors [mm] 1944 1944 1924 1944

Height (without antenna) [mm] 1488 1488 1488 1488

Length of load compartment floor [mm] 703 703 703 1257

16) In conjunction with 17 inch wheels, weight decreased by 15 kg.

210 Technical data

5-door vehicle 3-door vehicle VXR Van

Length of load compartment with folded rear seats [mm] 1348 1348 1348 –

Load compartment width [mm] 944 944 944 944

Load compartment height [mm] 538 538 538 538

Wheelbase [mm] 2511 2511 2511 2511

Turning circle diameter [m] 10.2 10.2 10.2 10.2

Technical data 211

CapacitiesEngine oil

Engine A10XEPA12XEL,A12XER

A14XEL,A14XER,A14NEL

A16LER,A16LES

A13DTE,A13DTC

A13DTR,Z13DTJ A17DTS

including Filter [l] 3.0 4.0 4.0 4,5 3.5 3.5 5.4

between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0 1.0 1.0

Fuel tank

EngineA10XEP,A12XEL, A12XER

A14XEL,A14XER,A14NEL

A16LER,A16LES

Z13DTJ,A17DTS A13DTE

A13DTC,A13DTR

Petrol/diesel, nominal capacity [l] 45 45 45 45 45 40 45

LPG nominal capacity [l] – 4217) – – – – –

17) Fillable to 80% of its capacity.

212 Technical data

Tyre pressuresComfort with up to 3 people ECO with up to 3 people18) With full load

Engine Tyres front rear front rear front rear

[kPa/bar] ([psi])[kPa/bar]([psi]) [kPa/bar] ([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A10XEP 185/70 R14, 200/2.0 (29) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

185/65 R15,

185/60 R1519),

195/60 R15,

195/55 R1620)

18) To achieve the smallest amount of fuel consumption possible.19) Only permitted as winter tyres.20) No ECO pressure in combination with RunFlat tyres.

Technical data 213

Comfort with up to 3 people ECO with up to 3 people18) With full load

Engine Tyres front rear front rear front rear

[kPa/bar] ([psi])[kPa/bar]([psi]) [kPa/bar] ([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A12XEL,A12XER,A14XEL,A14XER

185/70 R14, 200/2.0 (29) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

185/65 R1521),

185/60 R1519),

195/60 R15,

195/55 R1620),

215/45 R1722)

21) On vehicles with a specific rear axle application in combination with limited steering angle and sport chassis: Onlypermitted as winter tyres. We recommend you consult a workshop.

19) Only permitted as winter tyres.20) No ECO pressure in combination with RunFlat tyres.22) On vehicles with a specific rear axle application in combination with limited steering angle and sport chassis. We

recommend you consult a workshop.

214 Technical data

Comfort with up to 3 people ECO with up to 3 people18) With full load

Engine Tyres front rear front rear front rear

[kPa/bar] ([psi])[kPa/bar]([psi]) [kPa/bar] ([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A14NEL 195/65 R15, 230/2.3 (33) 210/2.1 (30) 280/2.8 (41) 260/2.6 (38) 250/2.5 (36) 320/3.2 (46)

196/60 R1623),

205/55 R16,

225/45 R17

225/40 R18 250/2.5 (36) 230/2.3 (33) – – 270/2.7 (39) 320/3.2 (46)

A16LER 195/55 R1624), 240/2.4 (34) 220/2.2 (32) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

205/50 R1619),

215/45 R17

225/35 R18 260/2.6 (38) 240/2.4 (34) – – 280/2.8 (41) 320/3.2 (46)

A16LES 205/45 R1719) 240/2.4 (34) 220/2.2 (32) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

225/35 R18 260/2.6 (38) 240/2.4 (34) – – 280/2.8 (41) 320/3.2 (46)

23) When used as winter tyres, tyre chains are not permitted.24) Only permitted as winter tyres. Tyre chains not permitted.19) Only permitted as winter tyres.

Technical data 215

Comfort with up to 3 people ECO with up to 3 people18) With full load

Engine Tyres front rear front rear front rear

[kPa/bar] ([psi])[kPa/bar]([psi]) [kPa/bar] ([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A13DTC 185/65 R1523), 200/2.0(29) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

185/70 R1427),

215/45 R1725),

195/60 R1525),

195/55 R1620)

185/60 R1526), 220/2.2 (32) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

A13DTE 175/70 R14 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 320/3.2 (46)

185/60 R1526) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 320/3.2 (46)

185/65 R15 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 320/3.2 (46)

185/70 R14 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 250/2.5 (36) 270/2.7 (39) 320/3.2 (46)

23) When used as winter tyres, tyre chains are not permitted.27) Not in combination with limited steering angle and sport chassis. Only permitted with certain brake systems. We

recommend you consult a workshop.25) Not permitted as winter tyres. Tyre chains not permitted.20) No ECO pressure in combination with RunFlat tyres.26) Only permitted as winter tyres.

216 Technical data

Comfort with up to 3 people ECO with up to 3 people18) With full load

Engine Tyres front rear front rear front rear

[kPa/bar] ([psi])[kPa/bar]([psi]) [kPa/bar] ([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A13DTR 185/60 R15 240/2.4 (34) 200/2.0 (29) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

185/65 R15 220/2.2 (32) 200/2.0 (29) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

195/55 R1620) 220/2.2 (32) 200/2.0 (29) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

195/60 R15 220/2.2 (32) 200/2.0 (29) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

215/45 R17 220/2.2 (32) 200/2.0 (29) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

20) No ECO pressure in combination with RunFlat tyres.

Technical data 217

Comfort with up to 3 people ECO with up to 3 people18) With full load

Engine Tyres front rear front rear front rear

[kPa/bar] ([psi])[kPa/bar]([psi]) [kPa/bar] ([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

Z13DTJ 185/70 R1427), 200/2.0 (29) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

185/65 R1528),

195/60 R15,

195/55 R1620),

215/45 R1729)

185/60 R1519) 220/2.2 (32) 180/1.8 (26) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

27) Not in combination with limited steering angle and sport chassis. Only permitted with certain brake systems. Werecommend you consult a workshop.

28) In combination with limited steering angle or sport chassis. Only permitted as winter tyres. We recommend you consulta workshop.

20) No ECO pressure in combination with RunFlat tyres.29) In combination with limited steering angle or sport chassis. We recommend you consult a workshop.19) Only permitted as winter tyres.

218 Technical data

Comfort with up to 3 people ECO with up to 3 people18) With full load

Engine Tyres front rear front rear front rear

[kPa/bar] ([psi])[kPa/bar]([psi]) [kPa/bar] ([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A17DTS 185/65 R1528), 240/2.4 (35) 220/2.2 (32) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

195/60 R15,

195/55 R1620),

215/45 R1729)

185/60 R1519) 260/2.6 (38) 220/2.2 (32) 270/2.7 (39) 250/2.5 (36) 260/2.6 (38) 320/3.2 (46)

all Temporary spare wheel 420/4.2 (61) 420/4.2 (61) – – 420/4.2 (61) 420/4.2 (61)

28) In combination with limited steering angle or sport chassis. Only permitted as winter tyres. We recommend you consulta workshop.

20) No ECO pressure in combination with RunFlat tyres.29) In combination with limited steering angle or sport chassis. We recommend you consult a workshop.19) Only permitted as winter tyres.

Customer information 219

Customer information

Vehicle data recording andprivacy ....................................... 219

Vehicle data recordingand privacyEvent data recordersData storage modules in thevehicleA large number of electroniccomponents of your vehicle containdata storage modules temporarily orpermanently storing technical dataabout the condition of the vehicle,events and errors. In general, thistechnical information documents thecondition of parts, modules, systemsor the environment:■ Operating conditions of system

components (e.g. filling levels)■ Status messages of the vehicle and

its single components (e.g. numberof wheel revolutions / rotationalspeed, deceleration, lateralacceleration)

■ Dysfunctions and defects inimportant system components

■ Vehicle reactions in particulardriving situations (e.g. inflation ofan airbag, activation of the stabilityregulation system)

■ Environmental conditions (e.g.temperature)

These data are exclusively technicaland help identifying and correctingerrors as well as optimizing vehiclefunctions.Motion profiles indicating travelledroutes cannot be created with thesedata.If services are used (e.g. repairworks, service processes, warrantycases, quality assurance),employees of the service network(manufacturer included) are able toread out this technical informationfrom the event and error data storagemodules applying special diagnosticdevices. If required, you will receivefurther information at theseworkshops. After an error has beencorrected, the data are deleted fromthe error storage module or they areconstantly overwritten.

220 Customer information

When using the vehicle, situationsmay occur in which these technicaldata related to other information(accident report, damages on thevehicle, witness statements etc.) maybe associated with a specific person -possibly, with the assistance of anexpert.Additional functions contractuallyagreed upon with the client (e.g.vehicle location in emergency cases)allow the transmission of particularvehicle data from the vehicle.

Radio FrequencyIdentification (RFID)RFID technology is used in somevehicles for functions such as tyredeflation detection and ignitionsystem security. It is also used inconnection with conveniences suchas radio remote controls for doorlocking/unlocking and starting, and in-vehicle transmitters for garage dooropeners. RFID technology inVauxhall vehicles does not use orrecord personal information or linkwith any other Vauxhall systemcontaining personal information.

Customer information 221

222

Index AAccessories and vehicle

modifications .......................... 142Active head restraints................... 35Adaptive forward lighting ..........

.................................... 83, 97, 153Adjustable air vents ................... 109Airbag and belt tensioners ........... 78Airbag deactivation ................ 43, 78Airbag system .............................. 41Air conditioning regular

operation ................................ 110Air conditioning system .............. 104Air intake .................................... 110Air vents...................................... 109Antilock brake system ................ 125Antilock brake system (ABS) ....... 80Anti-theft alarm system ................ 25Anti-theft locking system .............. 25Appearance care........................ 182Apply footbrake ............................ 82Ashtrays ....................................... 73Automatic anti-dazzle .................. 29Automatic light control ................. 95Automatic locking ........................ 24Automatic transmission ............. 117Auxiliary heater........................... 109

BBattery ....................................... 147Battery discharge protection ...... 102Battery voltage ............................. 88Bicycle rack.................................. 52Bonnet ....................................... 144Brake and clutch fluid................. 187Brake and clutch system ............. 79Brake assist ............................... 126Brake fluid .................................. 147Brake light switch ......................... 88Brakes ............................... 125, 147Breakdown.................................. 180Bulb replacement ....................... 150

CCapacities .................................. 211Car Pass ...................................... 19Catalytic converter ..................... 116Central locking system ................ 21Centre console lighting .............. 102Changing tyre and wheel size . . . 171Charging system .......................... 78Child locks ................................... 24Child restraint installation

locations ................................... 47Child restraints.............................. 45Child restraint systems ................ 45Cigarette lighter ........................... 73

223

Climate control ............................. 15Climate control systems............. 103Clock ............................................ 72Control indicators.......................... 76Control of the vehicle ................. 111Controls........................................ 68Convex shape .............................. 27Coolant and antifreeze............... 187Cruise control ...................... 83, 128Cupholders .................................. 51Curtain airbag system .................. 43Curve lighting................................ 97

DDanger, Warnings and Cautions . . . 4Deflation detection system........... 81Diesel fuel system bleeding ....... 149Diesel particle filter .................... 115Doors............................................ 24Drain diesel fuel filter ................... 88Driving characteristics and

towing tips .............................. 137Driving hints................................ 111

EEasytronic................................... 121Electric adjustment ...................... 27Electrical system......................... 163Electronic climate control

system .................................... 105

Electronic driving programmes ......................................... 118, 122

Electronic Stability Program 80, 127End-of-life vehicle recovery ....... 143Engine compartment fuse box ... 164Engine coolant ........................... 146Engine coolant temperature ........ 81Engine data ............................... 195Engine exhaust .......................... 115Engine oil ................... 145, 187, 192Engine oil pressure ...................... 81Entry lighting .............................. 102Event data recorders.................. 219Exit lighting ................................ 102Exterior care .............................. 182Exterior light ................................. 82Exterior lighting ...................... 12, 95Exterior mirrors............................. 27

FFault ................................... 119, 124First aid......................................... 65First aid kit ................................... 65Fixed air vents ........................... 109Flex-Fix system............................ 52Fog light ....................................... 83Fog lights ................................... 156Folding ......................................... 27Front airbag system ..................... 41Front fog lights ............................. 99

Front seats.................................... 35Front turn signal light.......... 151, 153Fuel............................................. 130Fuel consumption - CO2-

Emissions ............................... 136Fuel for diesel engines .............. 131Fuel for liquid gas operation....... 131Fuel for petrol engines ............... 130Fuel gauge ................................... 75Fuel selector ................................ 75Fuses ......................................... 163

GGauges......................................... 74General information ................... 137Glovebox ..................................... 51Graphic-Info-Display, Colour-

Info-Display .............................. 84

HHalogen headlights .................... 151Hand brake......................... 125, 126Hazard warning flashers .............. 98Headlight flash ............................. 96Headlight range adjustment ........ 96Headlights..................................... 95Headlights when driving abroad . . 97Head restraint adjustment ............. 7Head restraints ............................ 34Heated mirrors ............................. 28

224

Heated rear window ..................... 31Heated steering wheel ................. 69Heating ........................................ 38Heating and ventilation system . 103High beam ............................. 82, 96Hill start assist ........................... 126Horn ....................................... 13, 69

IIdentification plate ..................... 190Ignition switch positions ............. 112Immobiliser .................................. 26Indicators...................................... 74Information displays...................... 83Instrument cluster ........................ 74Instrument panel fuse box ......... 165Instrument panel illumination

control .................................... 100Instrument panel overview ........... 10Interior care ............................... 184Interior lighting............................ 100Interior lights ...................... 100, 162Interior mirrors.............................. 29Interruption of power supply .....

........................................ 119, 124Introduction .................................... 3Isofix child restraint systems ........ 50

JJump starting ............................. 178

KKey, memorised settings.............. 21Keys ............................................. 19Keys, locks................................... 19

LLashing eyes ............................... 64Lighting ........................................ 88Lighting features......................... 102Light switch .................................. 95Load compartment ................ 24, 61Load compartment cover ............. 62Load compartment fuse box ...... 166Load compartment lighting......... 101Loading information ..................... 66Low engine oil level ..................... 82Low fuel ....................................... 82

MMalfunction indicator light ............ 79Manual anti-dazzle ...................... 29Manual mode ............................. 122Manual transmission .................. 120Manual transmission automated 121Manual windows .......................... 30Memorised settings...................... 21Mirror adjustment ........................... 8Misted light covers ..................... 100

NNew vehicle running-in .............. 111Number plate light ..................... 161

OObject detection systems........... 129Odometer ..................................... 74Oil, engine.......................... 187, 192Outside temperature .................... 71Overrun cut-off ........................... 113

PParking ................................ 18, 115Parking assist ............................ 129Parking brake ............................ 126Parking lights ............................... 99Particle filter................................ 115Performance .............................. 198Performing work ........................ 143Pollen filter ................................. 110Power outlets ............................... 73Power steering.............................. 80Power windows ............................ 30Preheating and diesel particle

filter .......................................... 81Puncture..................................... 175

QQuickheat................................... 109

225

RRadio Frequency Identification

(RFID)..................................... 220Radio remote control ................... 20Reading lights ............................ 101Rear carrier system...................... 52Rear floor storage cover .............. 64Rear fog light ............................... 83Rear fog lights ............................. 99Rear window wiper/washer .......... 71Recommended fluids and

lubricants ........................ 187, 192Refuelling ................................... 133Reversing lights ......................... 100Ride control systems.................. 127Roof.............................................. 32Roof rack ..................................... 65

SSeat adjustment ....................... 6, 36Seat belt ........................................ 8Seat belt reminder ....................... 78Seat belts ..................................... 38Seat folding .................................. 37Seat position ................................ 35Selector lever ..................... 117, 121Service ............................... 110, 186Service display ............................ 76Service information .................... 186

Service vehicle soon .................... 79Side airbag system ...................... 42Sidelights...................................... 95Side turn signal lights ................ 160Smartphone controller.................. 87Spare wheel ............................... 177Speedometer ............................... 74Sport mode .................................. 80Starting and operating................ 111Starting off ................................... 16Starting the engine ............ 112, 121Steering wheel adjustment ...... 9, 68Steering wheel controls ............... 68Stop-start system........................ 113Stop watch ................................... 92Storage......................................... 51Storage compartments................. 51Sunroof ........................................ 32Sun visors .................................... 31Symbols ......................................... 4

TTachometer ................................. 75Tail lights ................................... 157Three-point seat belt .................... 39Tools .......................................... 167Top-tether child restraint

systems .................................... 50Towing................................ 137, 180Towing another vehicle ............. 181

Towing equipment ..................... 138Towing the vehicle ..................... 180Trailer coupling........................... 137Trailer towing ............................. 137Transmission ............................... 15Transmission display ... 76, 117, 121Tread depth ............................... 170Trip computer .............................. 89Trip computer in Graphic-Info-

Display or Colour-Info-Display . 90Triple-Info-Display ....................... 83Trip odometer .............................. 75Turn and lane-change signals ..... 98Turn signal ................................... 78Tyre chains ................................ 172Tyre deflation detection system . 170Tyre designations ...................... 169Tyre pressure ............................ 169Tyre pressures ........................... 212Tyre repair kit ............................. 172Tyres .......................................... 169

UUltrasonic parking assist ...... 80, 129Underseat storage ....................... 52Upholstery.................................. 184Upshift.......................................... 80Using this manual .......................... 3

226

VVehicle checks............................ 143Vehicle data................................ 192Vehicle data recording and

privacy..................................... 219Vehicle dimensions .................... 209Vehicle Identification Number .... 190Vehicle jack................................ 167Vehicle messages ....................... 87Vehicle personalisation ............... 93Vehicle security............................ 25Vehicle specific data ...................... 3Vehicle storage........................... 142Vehicle tools............................... 167Vehicle unlocking ........................... 6Vehicle weight ........................... 202Ventilation................................... 103

WWarning chimes ........................... 87Warning lights............................... 74Warning triangle .......................... 65Washer and wiper systems ......... 14Washer fluid ............................... 146Wheel changing ......................... 175Wheel covers ............................. 171Wheels and tyres ....................... 169Windows....................................... 29Windscreen................................... 29

Windscreen wiper/washer ........... 70Winter mode ................................ 80Winter tyres ............................... 169Wiper blade replacement .......... 149