owner's twin over full bunk manual bed attach here · twin over full bunk bed tg-btc01e...
TRANSCRIPT
MODEL #:
NOTE:THIS INSTRUCTION BOOKLET
CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND
KEEP FOR FUTURE REFERENCE.
UPC CODE:TG-BTC01E 0-65857-14566-3
TG-BTC01W 0-65857-15044-5
OWNER'SMANUAL
TWIN OVER FULL BUNK
BED
TG-BTC01E ESPRESSO
TG-BTC01W WHITE
RECEIPT OF PURCHASE:
ATTACH HERE
DATE OF PURCHASE:
DO NOT RETURN PRODUCT TO THE STORE. If a part is missing or damaged, contact our customer service department. We will replace the part FREE of charge.
Tel # : 1-800-295-1980 E-Mail: [email protected] Fax #: 514-353-7819
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada, H1G 3L1
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service
representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product model
number, color and a detailed description of the part.
Customer Service Department No. 413
E-MAIL: [email protected]
WARNINGSTRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE BUNK
BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT NOT LIMITED
TO HOOKS, BELTS AND JUMP ROPES.
FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK END
STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM BED.
PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK BED
WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL LENGTH OF
THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT ENTRAPMENT BETWEEN
THE BED AND WALL (APPLICABLE FOR BUNK BEDS WITH FULL LENGTH GUARDRAILS ON
ONE SIDE).
PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER AND OTHER
COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL
CONNECTORS ARE TIGHT.
DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED.
THE MATTRESS PLATFORM IS DESIGNED TO SUPPORT A MATTRESS WITHOUT THE NEED
FOR A POSTURE BOARD OR BOX SPRING.
USE ONLY COIL SPRING MATTRESSES ON BOTH THE UPPER AND LOWER BUNKS. FAILURE
TO DO SO CAN RESULT IN INJURY.
ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH, TO
HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS.
USE ONLY MATTRESSES WHICH ARE 74"-75" LONG AND 37 1/2" - 38 1/2" WIDE ON UPPER
AND ON LOWER BUNKS. ENSURE THICKNESS OF MATTRESS DOES NOT EXCEED 6".
SURFACE OF MATTRESS MUST BE AT LEAST 5" (127MM) BELOW THE UPPER EDGE OF
GUARDRAILS.
DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
DO NOT USE SUBSTITUTE PARTS. CONTACT CUSTOMER SERVICE FOR REPLACEMENT
PARTS.
USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD USING THE
UPPER BUNK.
KEEP THESE INSTRUCTIONS FOR FUTURE USE.
*
*
*
*
*
*
*
*
Check bolts/screws periodically and tighten them if necessary.
NOTES
PHILLIPS HEAD SCREWDRIVER (NOT INCLUDED) IS REQUIRED.
A RUBBER MALLET (NOT INCLUDED) IS RECOMMENDED TO FACILITATE ASSEMBLY.
READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH STEP
OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS ARE NOT
FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN RESULT IN
INJURY.
ADULT ASSEMBLY REQUIRED.
ASSEMBLY WILL REQUIRE TWO PEOPLE.
MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A
SMOOTH SOFT SURFACE.
WARNING: Should this product
become damaged, and/or components
are broken or missing, DO NOT USE.
BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG TEENAGERS.
Dust regularly with a soft, dry cloth. We do not recommend the use of chemical cleaners or wax on
our lacquered furniture as it may damage the finish. Keep solvents, alcohol, nail polish and polish
removers away from your hardwood furniture surfaces.
MAINTENANCE
DOREL ASIA LIMITED WARRANTY
DOREL ASIA warrants its product to be free from defects in material and workmanship and agrees
to remedy any such defect. This warranty covers 1 year from the date of original purchase. This
warranty is valid only upon presentation of proof of purchase. This is solely limited to the repair or
replacement of defective furniture components and no assembly labor is included. This warranty
does not apply to any product which has been improperly assembled, subjected to misuse or abuse
or which has been altered or repaired in any way. This warranty gives you specific legal rights and
you may also have other rights which vary from State to State
CARE AND CLEANING
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
10mm x 50mm
10mm x 100mm4mm x 30mm
6.5mm x 100mm 4mm x 35mm
6.5mm x 48mm1/4" x 100mm
WOOD JOINT CONNECTOR (4mm HEX HEAD) 8 PCS
WOOD JOINT CONNECTOR (4mm HEX HEAD) 24 PCS
FLAT HEAD SCREW 28 PCS
FLAT HEAD SCREW 3 PCS
METAL DOWEL 4 PCS
WOOD DOWEL 32 PCS
BARREL NUT 16 PCS
HEX KEY 1 PC
JOINT CONNECTOR (4mm HEX HEAD) 16 PCS
11.8mm x 15mm
HARDWARE LIST
1 2
3 4
5 6
7 8
9 10
11 12
HEX CAP 4 PCS
1/4" x 38mm
JOINT CONNECTOR (4mm HEX HEAD) 7 PCS
4mm x 19mm
FLAT HEAD SCREW 2 PCS
9mm x 17mm
13
STOPPER 44 PCS
1
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
PARTS LIST
BOTTOM POST 2 PCS
A B C
ED F
B
A
C
D
E
E
F
F
G
H
K
L
M
N
O
O
P
Q
R
S
T
U
W
XY
Z
BOTTOM POST 2 PCS
2
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
SHORT GUARDRAIL 2 PCS
BOTTOM SIDE RAIL (WITH NO HOLE) 2 PCS
TOP SIDE RAIL (WITH 1 HOLE) 1 PC
TOP SIDE RAIL (WITH 4 HOLES) 1 PC
BOTTOM HEADBOARD SLAT 26 PCS
TOP HEADBOARD SLAT 18 PCS
BOTTOM HEADBOARD TOP CROSS 2 PCS
TOP HEADBOARD BOTTOM CROSS 2 PCS
BOTTOM HEADBOARD BOTTOM CROSS 2 PCS
TOP HEADBOARD TOP CROSS 2 PCS
P Q R
ONM
LKJ
PARTS LIST
G H I
3
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
Y
V1
UTS
PARTS LIST
W
X Z
LEFT LADDER END 1 PC
RIGHT LADDER END 1 PC
LADDER STEP 4 PCS
TOP SLAT 7 PCS
BOTTOM SLAT WITHOUT HOLE 4 PCS
V2
LEFT SHORT GUARDRAIL POST 1 PC
RIGHT SHORT GUARDRAIL POST 1 PC
A1
SPACE BLOCK 2 PCS
SUPPORT POST 3 PCS
BOTTOM SLAT WITH 1 HOLE 3 PCS
4
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
NOTES: Top headboard top cross (G) and top headboard bottom cross (H) may require that they
be pulled closer together or further apart in order to allow wood dowels (7) to align with holes in
top posts (A and B).
Insert stoppers (13) and top headboard slats (K) into the holes of the top headboard bottom cross
(H) and push down until firmly in place. Slide top headboard top cross (G) onto top headboard
slats (K). Insert wood dowels (7) into ends of top headboard top cross (G) and bottom cross (H).
Attach top posts (A & B) using wood joint connectors (3) as shown.
STEP 1
One of the top headboard top cross (G) has a label on it. Use it in this step.
G
K
H
3
A
G
H
K
5
STEP 2
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
Repeat the previous step to assemble the remaining top headboard using top posts (C & D).
Repeat Step #1 to assembly the bottom headboards using bottom headboard slats (L), bottom
headboard top cross (I), bottom headboard bottom cross (J), and bottom posts (E & F).
NOTE: Bottom headboard top cross (I) has 2 holes on it to insert metal dowels in Step 7. One
hole is located near the center, the other is an end. Make sure that one bottom post (E) and
one bottom post (F) are each attached to the end of one bottom top cross (I) with the metal
dowel holes. Refer to above illustration for the exact location.
J
6
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
Attach the two bottom headboards with bottom posts (E and F) to bottom side rails (O) using
joint connectors (1) and barrel nuts (8) as shown.
Note: This is the lower bunk.
STEP 3
8
F
E
E
F
7
STEP 4
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
You've finished assmebling the lower bunk.
Attach a bottom slat without hole (X) onto bottom side rails (O) of the bottom bunk (as close to
the headboard as possible) with flat head screws (4). Attach the other slats (X & Y) to the bottom
side rails (O) with flat head screws (4) using a Phillips head screwdriver (not included). Use
space block (A1) to space the slats out evenly as shown.
NOTE: If you notice that any of the slats (X & Y) are not perfectly flat, be sure to assemble them
so that the slats (X & Y) curves up in the middle and down on the ends.
Attach the support post (Z) to bottom slats with 1 hole (Y) of the bottom bunk with joint
connectors (12) and hex key (9) as shown.
II JH1Headb FootboardHeadboarSIDE RAIL WOOD SCREWSSLAT NOTE:DIAGRAM 1 DIAGRAM 2 A
14 PCS4
12 3 PCS
8
STEP 5
Insert a wood dowel (7) into each end of the long guardrails (P). Attach two long guardrails
(P) and two top side rails (M and N) to top posts (A and B) & (C and D) as shown. Fasten
top side rails (M and N) with joint connectors (1) and barrel nuts (8). Fasten long guardrails
(P) with wood joint connectors (3). Use hex key (9) to tighten all joint connectors (1).
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
B
C
D
M
9
STEP 6
Attach a top slat (W) onto top side rails (M & N) of the top bunk (as close to the headboard as
possible) with flat head screws (4). Attach the other slats (W) to the top side rails (M & N) with flat
head screws (4). Use space block (A1) to space them out evenly.
NOTE: If you notice that any of the slats (W) are not perfectly flat, be sure to assemble them so
that the slats (W) curves up in the middle and down on the ends.
Insert wood dowel (7) into each end of the short guardrails (Q). Attach two short guardrails (Q) to
short guardrail posts (V1 & V2) with wood joint connectors (3) as shown. Attach the short
guardrail posts (V1 & V2) to top side rail (M) with joint connectors (12) and hex cap (10) as
shown.
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
II JH1Headb FootboardHeadboarSIDE RAIL WOOD SCREWSSLAT NOTE:DIAGRAM 1 DIAGRAM 2 A
10
STEP 7
Attach the guardrail leg (R) to long guardrails (P) and top side rail (N) with flat head
screws (5).
Insert four metal dowels (6) into the holes in the bottom headboard top crosses (I).
With the help if another peson, stack the top bunk onto the bottom bunk.
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
II JH1Headb FootboardHeadboarSIDE RAIL WOOD SCREWSSLAT NOTE:DIAGRAM 1 DIAGRAM 2 A
6 4 PCS
5 3 PCS
11
STEP 8
To assemble the ladder, insert wood dowels (7) into the end of the ladder steps (U). Attach
left ladder end (S) and right ladder end (T) to ladder steps (U) with wood joint connectors
(2) and hex key (9).
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
II JH1Headboard FootboardHeadboard SIDE RAIL WOOD SCREWSSLAT NOTE:DIAGRAM 1 DIAGRAM 2A
12
STEP 9
Attach the ladder to the top side rail (M) with flat head screw (11) as shown.
TWIN OVER FULL BUNK BEDTG-BTC01E ESPRESSO / TG-BTC01W WHITE
II JH1Headb FootboardHeadboarSIDE RAIL WOOD SCREWSSLAT NOTE:DIAGRAM 1 DIAGRAM 2 A
11
11M
13
TWIN OVER FULL BUNK BED
TG-BTC01E ESPRESSO / TG-BTC01W WHITE
To convert the bunk bed into a twin bed and full size bed, remove the ladder and all the
guardrails. With the help of another person, remove the top bunk from the lower bunk.
twin bedfull bed
To be used asthe headboard
for twin bed
To be used as
the headboardfor full bed
To be used asthe headboard
for full bed
To be used as
the headboardfor twin bed
14
TWIN OVER FULL BUNK BED
TG-BTC01E ESPRESSO / TG-BTC01W WHITE
USE ONLY MATTRESSES WHICH ARE 74"-75" LONG AND 37 1/2" - 38 1/2"
WIDE ON UPPER BUNK AND AT LEAST 27 1/4" BY 51 5/8" ON LOWER
BUNK. ENSURE THICKNESS OF MATTRESS DOES NOT EXCEED 6".
DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE OR WEIGHING MORE THAN 150
LBS TO USE THE UPPER BUNK. BED IS DESIGNED FOR CHILDREN RANGING
FROM 6 YEARS OF AGE TO YOUNG TEENAGERS.
DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT
JUMPING ON THE BED.
DO NOT RETURN PRODUCT TO THE STORE. If a part is missing or damaged, contact our customer service department. We will replace the part FREE of charge.
Tel # : 1-800-295-1980 E-Mail: [email protected] Fax #: 514-353-7819
15
MODEL #: TG-BTC01E ESPRESSO / TG-BTC01W WHITE
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING
NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).
Request Date:
Name:
Shipping Address:
Street & Number:
City & State:
Zip Code:
Day Time Phone Number:
(including area code)
Date & Place of Purchase:
Part(s) description and quantity: (Please be sure to list model number or SKN number)
Customer Service Representative Mailing Address:
Customer Service Department No. 413, 12345 Albert-Hudon Boulevard, Suite 100, Montreal, QC, Canada, H1G 3L1
Customer Service
Customer Service Phone Number 1-800-295-1980Email: [email protected]
Customer Service Fax Number 514-353-7819
C B DEAB BB