oxymag floor boards - iti australia installation guide low res v2.3.pdfiti australia pty ltd oxymag...
TRANSCRIPT
A. REQUIREDPRODUCT / ACCESSORIES / TOOLS
A1. PRODUCT DESCRIPTIONOxy-Mag • High
• T • • a • all • AS • •
y
Oxy-Mag NCC BCA
Oxy-Mag ITI 02 8805
The Oxy-Mag floor boards come in the following sizes:
Part No. Length mm Width mm Thickness mm Mass kg Units/Pack
2700
2700
600
600
16 33 33
19 39 28
MGF2700X60016
MGF2700X60019
Oxy-Mag
all
T
FIGURE 1 – PRODUCT
A2. RECOMMENDED TOOLS & ACCESSORIES
FIGURE 2 – ACCESSORIES
Electric or Battery Powered Screw Driver:
Paint Scraper or Spatula:
Dust Extractor Compatible with Circular Saw: - HEPA
Compressed Air, Gas or Battery Nail Guns:
Saw Blade: A
Dust Extraction Circular Saw:
Foam Backing Rod: A all
OXYMAG FLOOR BOARDSINSTALLATION GUIDE� � � � � � � �� � � � � � � � ���� � � � � �� � � � � �
ITI Australia Pty Ltd P 1/4OxyMag Installation Guide v20180910
Site-Applied Primer: A Oxy-Mag
Oxy-Magg 3
DESCRIPTION
Construction Adhesive:
Screw for Steel Frames: 3 imum -
QuikDrive Collated Screw: V
Joint Sealant: - A all
Nail - Ring Shank: 50 x
Nail: 50 x
Nail - D Head: 50 x D
Screw for Timber Frames: 3 imum - 10g x
RECOMMENDED BRANDS
D
x
W T 10g
k
k
PPG T
B6. FRAMINGOxy-Mag typically
• with NCC BCA –
T with AS
with AS • with ’
B5. FASTENERS
* = A 3 all ** = ’ *** = Quick
a
fully with all with which
B. GENERAL COMMENTS APPLICABLE TO INTERNAL & EXTERNAL APPLICATIONS
B1. SCOPEwith Oxy-Mag
B2. STORAGE• Oxy-Mag y at all • • maximum • maximum B3. SAFE WORKING PRACTICES & HANDLINGOxy-Mag a
at all • A y •
cut cut that will away
If that it with • a
A y a
• • Data B4. DESIGNB4.1. GeneralIt that all with
NCC & BCA
B4.2. ResponsibilityIt it that Oxy-Mag that a
that fall ITI it
that with BCA
B4.3. LoadingOxy-Mag floor boards are designed to withstand various load catagories in Table 3.1 of AS/NZS 1170.1 for imposed floor actions. Oxy-Mag’s load capacities for450mm joist centres are reflected in the below table (refer to comprehensive design/load tables at www.itiaustralia.com.au/):
T 3
FIGURE 3 – BOARD LAYOUT – STAGGERED PATTERN
Butt fully
Off-cut a 2
- 3
T
2* = 350mm2** =
*** = Can be used up to 600mm joist centres for residential applications only
B8. FINISHESB8.1. General• F all i h th Oxy-Mag b a
Mak u that y c mp t f th i h y t m i c mpl t ly c mpatibl with ach th a wa a t f th i pla u with Oxy-Mag i g
Th i t i h y t m mu t b i tall i c mplia c with th ma ufactu ’ p ci cati a i tallati i t ucti• B a mu t b cl a a t tally y b f applyi g th i t i h• D t a th Oxy-Mag b a Sh ul th b a ’ g ha light h ight iff c ( t m tha 3mm l l th ut by applyi g a app p iat lf-l lli g p uct that i c mpatibl with th i t i h• I lati t w t a a it i tial that th i tallati c mpli with AS 3740 AS 3958 a a y th l a t gulati• A i gl c at f p im h ul b appli it t th u fac a th xt al p im t g f th Oxy-Mag b a aft i tallati Th aft th b a h ul t b l ft u c a with ut a i h f a xt p i W c mm that th al c i g i h b appli t th Oxy-Mag b a withi 4 m th aft i tallatiB8.2. Vinyl• Th i tallati f i yl t Oxy Mag b a i th am a f a y th ub t at b a a ui xt a p pa ati• Th u f th a a mu t b ci p i t w k ta ti g - g I t al y a a I t al high t af c a a I t al w t a a tc• C ult with l a t i yl ma ufactu f th app p iat t t a wa a t i yl p uct a w ll a i cti f th i i tallatiB8.3. Carpet• Th u fac f th Oxy-Mag b a may ui p imi g b f applyi g a h i• U lay
M t u lay ca b p t x with tapl b a pi a h i C umb f am a y th tic u lay a u ually l lai a p im t
tapl J i t h ul b tap mly t g th
• Ca p t may b x t Oxy-Mag b a u i g p im t tapli g tacki g tackl y t m a h i i tallati y t m
Timber Joist (min 45mm wide) TTimber I-Joist LVL Solid Joist
(only internal)Steel Joist
0.75-1.6mm BMTSteel Joist
between 1.6 & 1.9mm BMT
Table 2 – Fastener Selection*
Product
50 x 2.8mm FC nails
50 x 2.87mm D Head gun nails
50 x 2.87mm Ring Shank Nail
10g x 50mm self-drilling screw
Self-tapping wing-tipped 40mm
screw**
Various QuikDrivescrews***
Table 3 – Board Layout Selection
Internal / External Finish Control Joints(indicative only)
Internal
External
External
Tiled dry & wet areas
Waterproof system and tiling direct
Waterproof system, slip board, reinforced mortabed and tile
5.4m in direction of board
2.7m in direction of board and 4.2m in direction of joists
4.1m in direction of board
Internal
Board Layout
Staggered
Squared
Staggered
StaggeredVinyl, Carpet, Timber, etc (not Tiled)
Not required unless specified by engineer / specifier
B7. BOARD LAYOUT AND SIDE UP• (butt fully • may a 3 4 • with
• at 45mm
at 40mm
LVL at 42mm • • • (butt at all by a • – 1mm y 1m all •
FIGURE 4 – BOARD LAYOUT – SQUARED PATTERN
Butt fully
T
ITI Australia Pty Ltd P 2/4OxyMag Installation Guide v20180910
Oxy-Mag Floor board thickness
- mm
Table 1 – Load Capacities for 450mm Joist Centres
Concentrated Action Residential
- kN*
Uniformly Distributed Action - kPa
16
19***
10
2.7 12
1.8
Concentrated Action Light
Commercial - kN**
3.6
2.7
B9. MAINTENANCE• A single coat of suitable primer should be applied on site to the surface and the external perimeter edges of the Oxy-Mag boards immediately after installation. Even with the coating of primer, the boards should not be exposed to the weather for more than 3 months.• The Oxy-Mag boards’ surface, joints, etc should be cleaned and maintained at regular intervals.
Installation of BoardsFigures 5 and 6 below show how to install the Oxy-Mag boards in a staggered pattern. When installing the boards in a squared pattern the boards must be laid squared and aligned to each other and must not be offset. Prior to installation, determine board layout and control joint placement - see the board layout section B7.
The following installation steps apply to both internal and external applications:
The following installation steps relate to butt joints in External applications. The drawing the boards in a squared pattern but applies equally to the boards in a staggered pattern.
B8.6 Tiling• In all cases, tiles must be installed in accordance with AS 3958, the NCC and the BCA.• Tiles can be laid either directly on the Oxy-Mag oor boards or on a sand-cement mortar bed over the boards (this applies to both wet and dry areas). For some applications, this mortar bed may need to be reinforced.• Points to highlight:
The tiles must be laid from the control joint out and the tiles’ edges must extend over the butt joints by a minimum of 50 mm.
Always use a exible adhesive that is suitable for the tile thickness and size For all other matters, consult with the tile manufacturer and/or the waterproo ng
supplier and/or the applicable tiling standards and regulations.
STEP 5Slot Board 3 into Board 1. Butt joint Board 3 to Board 2 on the same joist. Fasten Board 3 with the same layout as Board 1 and Board 2
STEP 3Apply a full length, continuous 3mm diameter bead of joint sealant into the bottom of the groove of Board 1
STEP 4Slot Board 2 (an off-cut / less than full-size board) into Board 1. Remove any excess sealant from the surface of the boards by using a spatula. Fasten Board 2 in place as per the fastener layout
25mm min. from groove edge
BOARD 1
BOARD 2
BOARD 3
Butt joint
BOARD 1
BOARD 2
Joint Sealant
STEP 6Once each of Board 2 and Board 3 are in place, install the row of fasteners adjacent to the long groove edge on Board 1. Ultimately there must be a minimum of 4 fasteners per board-width over all joists, including each individual board’s butt ends
Note: An off-cut may be used as a starter for the next row as long as the starting-joint is staggered at least 400mm away from the end-joint of the adjacent board and it covers a minimum of two joist spacings - ie: 3 joists
FIGURE 6 – FIXING SECOND AND THIRD BOARDS
Tongue edge
Note:The row of fasteners adjacent to the long groove edge should be installed later.
STEP 2Install Board 1 on the corner edge of the frame, across the joists, with the tongue edge on the perimeter frame and as per the fastener layout
STEP 1Apply a continuous 6mm bead of construction adhesive to joists.
200mmmax.
25mm min. from tongue edge
50mm min. from corner
Joist centres up to 600mm maxGroove edge
BOARD 1
Construction adhesiveon joist
Fasteners
12mm min. from short edge / butt end
Fastener Distances Summary
From Corner
Spacing along Joists
From Tongue/Groove Edge
From Short Edge/Butt End
Min.
Max.
Min.
Min.
50mm
200mm
25mm
12mm
FIGURE 5 – FIXING FIRST BOARD
C. INTERNAL & EXTERNAL INSTALLATION C1. INTERNAL & EXTERNAL INSTALLATION : STEPS• Oxy-Mag boards and framing must be in a dry and clean state prior to installation.• The cementitious formulation of the Oxy-Mag oor boards means that the smooth and rough (sanded) surfaces will be subject to colour variations and pinholes. These do not compromise the structural integrity of the boards and ITI will not deem these to be a valid reason for a return.• Ensure that the boards’ size and thickness are appropriate for the application prior to installation.• Depending on the nish, the butt joints of the boards may require a gap. Consequently, a creep at the short end of the boards could happen and, over several boards, extra oor joists could be needed.• The following applies re waterproo ng of the Oxy-Mag oor boards:
Internal wet areas: Waterproo ng must be carried out in accordance with AS 3740, the NCC and the BCA.
External areas: For all external applications, Oxy-Mag boards must be fully waterproofed in compliance with AS 4654. Refer to Section D of this guide for the waterproo ng options.
The Oxy-Mag oor boards must not be in direct contact with ponded water at any time Accordingly, any damage or tear in the waterproo ng must be repaired immediately to prevent this happening.
To give the sealant an opportunity to set and dry out, walking, running etc. on the should be avoided for 24-48 hours. Until the has been applied, the
boards’ surface should be protected from any damage.
For internal applications in wet areas and all external applications of the Oxy-Mag boards, apply joint sealant over:
• all board joints – ensure that an unbroken seal has been formed; and• the heads of fasteners (which must be to the board prior to sealing)
The below table the appropriate butt joints for the different applications:
B8.4 Solid Timber Floorboards• The installation of solid timber oorboards onto Oxy Mag oor boards is the same as for any other substrate oor board and requires no extra preparation, tools and/or materials.• Use a full trowel of adhesive on the Oxy-Mag boards as opposed to the “Z-type” pattern of adhesive.• Secret nailing of the timber oorboards to Oxy-Mag boards can be done with standard type staples and an air compressor type gun.• Should top nailing be required, then a standard air compressor driven “T-nailer” can be used.B8.5 Floating Laminate Floorboards• The installation of oating laminate oorboards onto Oxy Mag oor boards is the same as for any other substrate oor board and requires no extra preparation• Follow manufacturer’s instructions.
FIGURE 7 – CREATING 5MM BUTT JOINT
5mmpackers
Construction adhesive
STEP B Install Board B to create a butt joint with a 5mm gap on the joist. Remove packers once Board B is installed.
STEP A Install Board A. Place two 5mm packers at Board A's butt end on the joist prior to the installation of Board B
BOARD A
BOARD B
INSTALLATION STEPS AND FASTENER LAYOUT
ApplicationGap between short edges/ butt ends
of adjoining boardsDescription of butt joint
Internal – Dry No gapAdjoining boards are fixed flush to each other. No joint sealant is required
Internal – Wet
External
2mm
5mm
Gap is filled with joint sealant
A 10mm backing rod is placed into gap and must remain 5mm below surface of board. Remaining gap is filled with joint sealant
TABLE 4 - Butt Joints
Installation Of Butt Joints
BUTT JOINT FOR EXTERNAL APPLICATIONS
• The boards should be kept dry and protected at all times. Ponded water should not be permitted to accumulate directly on the Oxy-Mag boards at any time. If it does happen, the ponded water must be eliminated immediately.• W must be maintained in accordance with AS 3740.
ITI Australia Pty Ltd P 3/4OxyMag Installation Guide v20180910
Note the following:• Additional control joints may be required in both directions depending on the application and the board layout. Accordingly, refer to AS 3958 for more conclusive, detailed guidance.• Control joints are typically not required in which do not have a tiled unless they have been by the engineer or .• The above advice on control joints is purely indicative. The frequency of control joints is dependent on many factors (eg: type of joists, joists spacing, climatic conditions, prevalence of air-conditioning, etc) and is ultimately the decision of the responsible engineer, and/or builder of the site.
C2. CONTROL JOINTS - Tiled areas onlyControl joints in the boards and extending through the tiles (see Figure 9 below for an example of an internal control joint) should be provided in the below applications as follows (unless compelled to do otherwise by the NCC, BCA and / or local regulations):• Internal dry and wet areas: Every 5.4m in direction of boards – See Figure 8 below.• External with waterproof system and tiling direct: Every 2.7m in direction of boards and 4.2m in direction of joists – See section D2.• External with waterproof system, slip board, reinforced mortar bed and tile: Every 4.1m in direction of boards – See section D3.In addition, include control joints:• where the direction of the changes (for example, an L-shaped room)• at entrances to a room where the tiled surface continues into the adjacent room• where existing structural joints are located.
Board and tile control joint
Direction of joists
Board edges approximately 3mm from walls and projections
Maximum 5.4m
FIGURE 8 – BOARD CONTROL JOINT LAYOUT
Joint sealantOxy-Mag
5mm Tile adhesive
Tile
Construction adhesive
Backing rod10mm diameter
Double-joist
FIGURE 9 – CONTROL JOINTS: INTERNAL BOARD AND TILE JOINT
D2. WATERPROOF SYSTEM 1: LIQUID MEMBRANE METHODBasic description and requirements:• Constitutes the application of an appropriate and approved waterproof liquid membrane system onto the Oxy-Mag boards with tiles laid directly to the membrane with compatible adhesive.• Floor boards have a squared layout.• A licensed applicator who is able to provide a guarantee for tiling direct should install the selected membrane system and its components.• Recommended control joints are 2.7m in the direction of the boards and 4.2m in the direction of the joists.• The tiler and builder should ensure that all board control joints extend from the joist up through the tiles and that tile control joint spacings adhere to the relevant tile codes.• The tiler and builder must ensure compliance with the NCC, BCA and all relevant standards / codes.
D3. WATERPROOF SYSTEM 2: SLIP PANEL AND REINFORCED MORTAR BEDBasic description and requirements:• Constitutes the application of the following onto the Oxy-Mag boards (in order):
Waterproof membrane system; Slip panel; Reinforced mortar bed – recommend the following:
depth is 50mm; control joints every 4.5m x 4.5m in mortar bed.
Another waterproof membrane system (recommended); Tiles.
• Floor boards have a staggered layout.• Represents the minimum requirement over a living space / habitable room• Recommended control joints in Oxy-Mag boards are 4.1m in the direction of the boards.• The tiler and builder must ensure that all mortar and/or board control joints and their spacings comply with the NCC, BCA and all relevant standards / codes.
D4: EXTERNAL INSTALLATION – FURTHER CONSIDERATIONSThe builder / project responsible person must ensure that:• The step down from the internal FFL level to the deck’s surface meets the minimum requirements of the NCC and BCA.• The minimum fall in the deck from the building to the outside edge is 1:100.• The decking must not have sumps for drainage.• The upright supports of a balustrade must be to the structural frame - ie: they may not be to the Oxy-Mag boards and must not damage the deck’s
E1. PRODUCT INFORMATIONOxy-Mag is an advanced reinforced cement composite board.
For a Summary of Physical Properties and/or a Safety Data Sheet (SDS) in regards to Oxy-Mag boards, visit www.itiaustralia.com.au or ask ITI on 02 8805 5000.
E. PRODUCT INFORMATION, WARRANTY & DISCLAIMER
E2. PRODUCT WARRANTYOxy-Mag boards have a 10 year product warranty. For terms and conditions ofthe product warranty refer to www.itiaustralia.com.au or ask ITI on 02 8805 5000.E3. DISCLAIMERThe information contained in this installation guide is presented as a “guide only” to the installer for the purpose of assisting them to more easily install the Oxy-Mag
boards. This manual is not a substitute for professional engineering and design consultation. At all times the installer must consult and follow:• Relevant building codes and including the NCC and BCA.• All tool and materials manufacturers’ instructions.
The information contained in this guide is subject to change by ITI without prior notice.
This installation guide is published and distributed on the basis that ITI is not responsible for the results of any actions taken by installers, builders and users based on information contained in this guide and/or based on any error or omission in this guide. ITI does not accept any responsibility whatsoever for any misrepresentation made by any person of the information contained in this guide and expressly disclaims all and any liability and responsibility to any person, whether a user or reader of this guide or not, in respect of claims, losses or damage or any other matter, either direct or consequential arising out of or in relation to the use and reliance, whether wholly or partially, upon any information contained or products referred to in this guide.
D. WATERPROOFING & EXTERNAL INSTALLATION
D1. WATERPROOFING SYSTEMSOxy-Mag boards may be installed externally (eg: as a deck) over durable timber or corrosion resistant light gauge steel frames under the following conditions:• Oxy-Mag boards are installed using a staggered pattern (as in Figure 3 above) or a squared pattern (as in Figure 4 above).• Oxy-Mag boards and resultant decks are made fully waterproof (ie: not only water-resistant) in accordance with AS 4654.2. Waterproof decks will have either:
1: liquid applied membranes - See section D2; or 2: a board membrane and mortar bed - See section D3.
• The entire system is purchased from and installed by the same manufacturer/supplier and all components are fully compatible with one another.• The manufacturer/supplier have warranted their system.
ITI Australia Pty Ltd P 4/4OxyMag Installation Guide v20180910