pabx with caller id
DESCRIPTION
MS48C. PABX with Caller ID. MS48C - PABX with Caller ID. MS48C is now ready for exports !!! Ergonomic Design in Plastic Cabinet Caller ID Detection SMS Transmission. MS48C - PABX with Caller ID. Allows sending / receiving SMS through standard extensions as an option . - PowerPoint PPT PresentationTRANSCRIPT
MS48CMS48C is is now ready now ready for for exportsexports!!!!!!
• Ergonomic Design in Plastic Cabinet
• Caller ID Detection
• SMS Transmission
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
• Allows sending / receiving SMS through standard extensions as an option.
• Detects and displays Caller ID on standard extensions equipped with Caller ID sets as an option.
• Supports all add-ons / features of MS48S (except for ID12).
• Holds battery switch which is accessible without opening the cover.
• BT104BT104 Caller ID Telephone is an appropriate choice for New MS48C (with Caller ID) as a Low End Keyphone.Low End Keyphone.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
Caller ID (CLID) & SMS can be integrated via EXP48C-CLID card. This card is to be installed on top of the motherboard if there are no expansion modules or on the lastly installed expansion module otherwise.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
N.C. – Used N.C. – Used for for Firmware Firmware Changes Changes
N.C. – Used N.C. – Used for for DebuggingDebugging
KTS Input of KTS Input of CLID ModuleCLID Module
KTS Output KTS Output to Consolesto Consoles
• The expansion modules of MS48C are called EXP48C. • EXP48S expansion modules of MS48S can also be used with MS48C. But CLID is not supported on the lines and extensions of EXP48S modules.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
No need to make separate grounding for EXP48C Expansion Modules. EXP48C is grounded once it is installed on the motherboard through a ground pin on the motherboard.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
All ground cables are All ground cables are collected at this point. collected at this point. MS48C should be MS48C should be grounded from this grounded from this ground terminal.ground terminal.
Ground Pin for EXP48CGround Pin for EXP48C
Extension / line connectors allow vertical cabling. The position of connectors has been changed from horizontal to vertical.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
CABLE CABLE HOLEHOLE
CABLE CABLE CHANNELCHANNELSS
CONNECTOCONNECTORSRS
12V- 7Ah battery can be located under the battery belt inside the cabinet.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
BATTERY BATTERY CONNECTIOCONNECTIONN
BATTERY BATTERY BELTBELT
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
SPS48 Power Card with transformers are surrounded by portable plastic casing.
PRES
PRES
SS
SLID
SLID
EE
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
HOW TO ACCESS POWER & BATTERY SWITCHES
POWER SWITCHPOWER SWITCH
BATTERY SWITCHBATTERY SWITCH
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
HOW TO MOUNT MS48C ON THE WALL
• Drive the screws to Drive the screws to the wallthe wall
•Hook the system on Hook the system on the screw through the screw through the peer holesthe peer holes
•Fix the third screw Fix the third screw to the wallto the wall
• MS48C detects Caller ID in FSK or DTMF through C.O. Lines.
• MS48C sends Caller ID in FSK to standard extensions.• Caller ID can be displayed on standard CLID
telephones with feed voltage not higher than 24V. • Line impedance is 900/1800 Ohm, complex
impedance.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
• The dimensions and weight of MS48S and MS48C are different from each other.
• Dimensions of MS48C are 39 cm x 13 cm (h) x 48 cm and its weight is 5 kg
• Dimensions of MS48S were 38 cm x 11 cm (h) x 43 cm and its weight is 8.25 kg
• With the launch of MS48C, MS48S is now obsolete. The motherboard, expansion modules and accessories of MS48S will continue to be available as spare parts only.
MS48C - PABX with Caller IDMS48C - PABX with Caller ID
Technical SpecificationsTechnical SpecificationsBasic Capacity 4/12
Expandable By 2/6, 4/12, 0/16Two boards can be installed on the basic capacity. Only one can be 2/6 or 0/16
Max. Capacity 48 Ports
Line Interface Loop Start with DP/DTMF Signalling
Extension Interface Station Loop 1200 Ohms Including Set
Power 230 VAC, 50 Hz; Optional. 12V Bat. Backup
Power Consumption 11W (Stand-by)
Environment 0 °C to 45 °C to 80% Humidity
Dimensions 39x13x48 cm
Weight 5 kg (Basic capacity without battery)
MS48C - PABX with Caller IDMS48C - PABX with Caller ID