ASY1-293MOBILE GONDOL A & END DECKPAGE 1 OF 3

I N S T A L L A T I O N I N S T R U C T I O N S

P. O . B OX 7 2 9 / T E R R E L L , T E X A S 7 5 1 6 0 / 9 7 2 . 5 6 3 . 5 7 4 4 / 8 0 0 . 7 7 6 . 2 3 4 9P. O . B OX 1 7 7 / G O O D W AT E R , A L A B A M A 3 5 0 7 2 / 2 0 5 . 8 3 9 . 6 3 5 4 / 8 0 0 . 6 3 3 . 6 2 8 2

REV# ECN# REVISION BY DATE

04 5*13242 ADDED BECGM TO PAGE 2 CAB 07/26/1303 5*10331ADDED NOTES, UPDATED HARDWARE CAB 10/27/11

REV#ECN# REVISION BY DATE

REV05

Assemble base shoes to uprightsas shown in ASY-046. Do this forall sections in runs to receive

mobile gondola assemblies.

1

Locate casters and install to cast-er runners. Slide caster into theretainer plate welded on the run-ners until it meets stop. Use ascrewdriver in the hole of the taband bend the tab out sufficiently totrap caster.

2BACKS, SPANNERS,BASE SHELVES NOT

SHOWN FOR CLARITY!REFER TO ASY-046 FOR

STANDARD SHELVINGASSEMBLY!

MGPC(NW)CONSISTS OF:(2) MGPCCR-(NW), RAILS(1) MGPC-HDWR, HARDWARE, CASTER, BOLTS & NUTS(4) MGPCSP, SPACER PLATE

GONDOLAS...

WARNING!NEVER EXCEED LOAD CAPACITY!FOR 36” TO 48” WIDE GONDOLA

SECTIONS, EQUALLY DISTRIBUTEDWEIGHT WILL BE NO MORE THAN

1000LBS! WITH END FRAMESTOTAL WEIGHT CAPACITY IS

REDUCED TO 900LBS!. FOR NW60” WIDE GONDOLAS EQUALLYDISTRIBUTED WEIGHT WILL BENO MORE THAN 750LBS! WITHEND FRAMES TOTAL CAPACITY

IS REDUCED TO 650LBS! WEIGHTON END FRAMES SHOULD NEVEREXCEED 300LBS EACH OR 600LBS

TOTAL BOTH SIDES!!!!!

INDIVIDUAL SHELVES SHALLNEVER EXCEED LOAD CAPACITY.

SEE ASY-046 FOR SHELF CAPACITY

The more weight applied onMobile Gondola the more

resistant in rolling theGondola.

!

NOTE: THIS PRODUCT WILL NOTWORK ON BASE SHOES BELOWNOM DEPTH OF 12

05 5-13701 UPDATED TO SHOW LATEST VERSION OF 1055-198, AND SAM 10/24/13 NOTES ABOUT HOLES AND CASTER INSTALLATION

ASY1-293MOBILE GONDOL A & END DECKPAGE 2 OF 3

I N S T A L L A T I O N I N S T R U C T I O N S

P. O . B OX 7 2 9 / T E R R E L L , T E X A S 7 5 1 6 0 / 9 7 2 . 5 6 3 . 5 7 4 4 / 8 0 0 . 7 7 6 . 2 3 4 9P. O . B OX 1 7 7 / G O O D W AT E R , A L A B A M A 3 5 0 7 2 / 2 0 5 . 8 3 9 . 6 3 5 4 / 8 0 0 . 6 3 3 . 6 2 8 2

REV05

Assistance will be required to boltthe caster runner assemblies to thebase shoes. Stand one baseshoe/upright assembly and positiona caster runner on each side ofboth base shoes, (4) in all. Usingthe provide 3/8”-16x3.5” bolts,secure through both caster run-ners, sandwiching the base shoebetween. Tighten securely, but do

not over tighten!

3

Repeat step 3 until run is stand-ing. On end base shoes where EndDecks WILL NOT be used, use theplate for end sections (MGSP) asshown.Install spanners, kickplates, backsand base shelves in accordancewith ASY-046. Use base end covers BECGM-(ND)-(HAND) to cap of sections that donot use end decks.

4HARDWARE CODE:MGPC-HDWR

CODE:MGPCSP

RAILCODE:MGPCCR-(NW)

BECGM-(ND)RIGHT

BECGM-(ND)LEFT

3/8-16x3.5” CARRIAGE BOLT

MAKE SURE FRONT EDGE OF RUNNER ISFLUSH WITH LARGE CLIP ON BASE SHOE BEND SMALL TAB DOWN

TOWARD CASTER USING A SCREWDRIVER TO SECURECASTER TO PLATE

INSTALL USING ONLYTOP AND BOTTOMHOLES

ASY1-293MOBILE GONDOL A & END DECKPAGE 3 OF 3

I N S T A L L A T I O N I N S T R U C T I O N S

P. O . B OX 7 2 9 / T E R R E L L , T E X A S 7 5 1 6 0 / 9 7 2 . 5 6 3 . 5 7 4 4 / 8 0 0 . 7 7 6 . 2 3 4 9P. O . B OX 1 7 7 / G O O D W AT E R , A L A B A M A 3 5 0 7 2 / 2 0 5 . 8 3 9 . 6 3 5 4 / 8 0 0 . 6 3 3 . 6 2 8 2

REV05

Install caster runners in the samemanner as gondola runners. Note:End Deck caster runners are LH &RH. See position of kickplate/covermount holes in diagram.

1

Snap side kicks in place into baseshoes. Front kickplate/cover capsover side kicks.

2

Position deck on top of assembly.Rails on underside of deck fit tooutside of side kicks.

3

DECK IN PLACE

END DECKS...

MGED(ND)-(LSD)(RSD)(NP)-(_)

WARNING!NEVER EXCEED LOAD

CAPACITY!MGED END DECKS

SHOULD NEVER EXCEED300 LBS EACH!

NEVER EXCEED TOTALWEIGHT OF 600LBS FOR

BOTH END DECKSCOMBINED!

!

CODE:MGEDCR(ND)R

CODE:MGEDCR(ND)L

CODE:MGEDSKP(ND)

CODE:MGEDEKP(ND)(ND)

DECKCODE:MGEDTOP(ND)(LSD)(RSD)