OWNER MANUAL

PROFESSIONAL MIXER

COMPACT MIXER

MIC MIC MIC MIC MIC MIC MIC MIC

LINE LINE LINE LINE LINE LINE LINE LINENO. TIME

CHANNEL 9/10 CHANNEL 11/12

EFF LEVEL

15 HALL 1

16 HALL 2

13 ROOM 1

14 ROOM 2

10 ROOM 3

9 PLATE 1

11 PLATE 2

12 PLATE 3

4 CHORUS

3 FLANGE

1 DELAY 1

2 DELAY 2

6 CHORUS/ROOM 1

5 CHORUS/ROOM 2

7 VOCAL CANCEL

8 ROTARY SPEAKER

000039MP3 PBC

PAMX2.82

DSP EFFECTS PROCESSOR

EFF EFF EFF EFF EFF EFF EFF EFF

EFF

Audiodesign SrlVia dell’industria, 28 - 42025 CAVRIAGO (RE)+39 0522 941444 - Fax +39 0522 942363www.audiodesign-pro.cominfo@audiodesign.it

SET�UP�MEMO

PAMX2 Series

MIC IN------MAIN OUT L/R74 dB @620 Ohm Load, balanced

MIC IN------REC OUT 58 dB @10 Kohm Load

ST LINE IN------MAIN OUT L/R 28 dB

MIC IN------AUX OUT71 dB @620 Ohm Load, unbalanced

MIC IN------REV OUT71 dB @620 Ohm Load

AUX IN------MAIN OUT L/R29 dB

Max gain Signal route Conditions

@620 Ohm Load, balanced

@620 Ohm Load, balanced

2 TK IN ------MAIN OUT L/R28 dB @620 Ohm Load, balanced

1

1

1

150 Ohm

600 Ohm

+10dB

-10dB

75 Ohm +4dB

1 100 Ohm 3mW @36ohm

Outputs Number Outputs modes

Stereo REC OUT

HEADPHONE

Balanced

Stereo out

Connector

2 RCA

3-poles TRS

Unbalanced

Unbalanced

2 XLR

AUX OUT

Stereo MAIN OUT

TRS

Output levelRated

ImpedanceOutputs

4-8-12

1

2 Kohm

20 Kohm

10 Kohm

-60dB

-40dB

-10dB

2 10 Kohm -10dB

Unbalanced

Unbalanced

Balanced

Balanced

Input modesNumber Connector

2 TRS

3-poles TRS

XLR

2 TRS

Inputs

Microphones

Mono LINE IN

Stereo LINE IN

Stereo AUX IN

1 10 Kohm -10dBUnbalanced 2 RCAStereo PLAY IN

Input levelRatedInput

Impedance

Channel EQ HI 12KHz MID 2.5KHz LOW 80Hz max equalizing value +/-15dB

Main Graphic EQ 125,250,500Hz,1,2,4,8 KHz max equalizing value +/-12dB

Effect Processor 16 effect DSP

<0.1% @+14dB 20~20000Hz 620 ohm loadTotal harmonic distortion

+1/-2dB @+4dB 20~20000Hz 620 ohm loadFrequency response

+20dB/+26dB<balanced> @0.5%THD 1KHz 620 ohm load Max out level

-124dB @ 150 ohm , at max gainMicrophone preamp E.I.N

PAGE 11

Introduction/Features… … … … … … … … … … … … 2

Precautions……………………………………………… 3

Mono channel section … … … … … … … … … … 4

The stereo channel … … … … … … … … … … 5

Master control section… … … … … … … … … … … 6

Effect List… … … … … … … … … … … … … … … … 7

Set up MEMO………………………………………… 8

System block diagram… … … … … … … … … … … 9

Application example… … … … … … … … … … … … 10

Specifications …………………………………………11

Connection cables……………………………………12

PAGE 2

14.5 VA

Power

Power consumption

Weight (Kg) 2,9 - 3.7 - 4,8

Dimensions(mm)

Type

INTRODUCTION�/�FEATURES

Welcome you using the this PAMX2.82 portable mixer.

This mixers have handsome outline, perfect functions.

It is easy to set or operate.

There is a effect processor within the unit, it must be a ideal equipment you need.

Please read this manual carefully to know all functions and operations of the products well, in order to operate the unit at the good condition.

FEATURES

All models offer the possibility to recork on the USB pen the MAIN OUT channels

4, 8 or 12 mono input channels and 2 stereo input channels.

2 auxiliary inputs and 2 auxiliary outputs.

USB Input and Mp3 control panel

Adopt low-noise discrete Mic pre-amplifier on all microphone inputs, 3-band frequency equalizer for each input channel.

Built-in +48V phantom power for condenser microphone.

Peak indicators on each mono input channel.

Real two groups output, 60mm slide fader.

2 groups of 12 LED level meter to show the main out level.

7-band stereo graphic EQ.

Insert function on each mono channel

16 Effects High Quality internal DSP

Volume control for headphone out.

Stereo record out and stereo in for tape play.

CONTENTS

SPECIFICATIONSNOTICEINSTRUCTION

1.Check the AC voltage before connecting the AC plug. Proper grounding is a necessary practice to prevent electric shock hazards to the operator, the microphone user, and the musicians who are wired to this unit.

2.Before switching on the main power, keep all the output fader all the way down to prevent damage or excessive noise caused by bad level adjustment, wrong wiring, defective cables or bad connection.

3.Always turn on the mixer before the power amplifier; turn off the mixer after the amplifier.

4.Always turn off the unit before connecting and disconnecting the unit from the power source.

5.Never use solvents to clean the unit. Clean with a soft, dry cloth.

AC110V;120V;220V; 230V Refer to the label on the back panel

PROFESSIONAL MIXER PROFESSIONAL MIXER

1 75 Ohm +4dBUnbalancedREV OUT TRS

1 USBUSB IN

4-8-12

PAMX2.42 - PAMX2.82 - PAMX2.122

261X352X44 - 340x366x44 - 473X352X44

PAMX2. Series PAMX2. Series

PAGE 3PAGE10

CONNECTION�EXAMPLE

1. Read all safety and operating instructions before using this product.

2. All�safety�and�operating�instructions�should�be�kept�forfuture reference.

3. Read and understand all warnings listed on the operating instructions.

4. Follow all operating instructions to operate this product.5. This product should not be used near water, i.e. a bathtub,

sink, swimming pool, wet basement, etc.6. Use only a dry cloth to clean this product.7. Do not block any ventilation openings. The product should not

be placed fat against a wall or placed in a built-in enclosure that will impede the fow of cooling air.

8. Do not install this product near any heat sources, suchas radiators, heat registers, stoves or any other apparatus(including heat–producing amplifers) that produces heat.

9. Do not defeat the safety purpose of the polarized orgrounding-type plug. A polarized plug has two blades withone�wider�than�the�other.�A�grounding-type�plug�has�twoblades and a third grounding prong. The wide blade or thethird�prong�are�provided�for�your�safety.�If�the�provided�plug�does�not�ft�into�your�outlet,�consult�an�electrician�forreplacement of the obsolete outlet.

10. Protect the power cord being walked on or pinched,particularly at plugs, convenience receptacles and the point where they exit from the apparatus. Do not break the ground pin of the power supply cord.

11. Only use attachments specifed by the manufacturer.12. Use only with the cart, stand, tripod, bracket,

or table specifed by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or whenunused for long periods of time.

14. Care�should�be�taken�so�that�objects�do�not�fall�and�liquidsare not spilled into the unit through the ventilation ports orany other openings.

15. Refer�all�servicing�to�a�qualifed�service�professional.�Servicing is required when the apparatus does not operate normally or has been damaged in any way, including damage to the power cord or plug, damage due to liquids spilled or objects dropped inside the unit, dropping the unit, or anything else that interrupts normal use of the unit.

16. WARNING: To reduce the risk of fre or electric shock, do not expose�this�apparatus�to�rain�or�moisture.

17. When a mains plug is used as the disconnect device, thedisconnect device shall remain readily operable.

Important�Safety�Instructions

Exposure to extremely high noise levels may causepermanent hearing loss. Individuals vary considerablyto noise-induced hearing loss but most will lose some hearing if exposed to intense noise for a suffcient period of time.

DANGER

THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE

OF NON-INSULATED “DANGEROUS VOLTAGE” WITHIN THE

PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE

TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS

THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE

OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)

INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT .

APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING

AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,

SHALL BE PLACED ON THE APPARATUS.

SAFETY�INSTRUCTIONS

PROFESSIONAL MIXER PROFESSIONAL MIXER

MIC MIC MIC MIC

LINE LINE LINE LINE

RIGHTLEFT

DIRECTBOX

000039MP3 PBC

COMPACT�MIXER

NO. TIME

CHANNEL 13/14 CHANNEL 15/16

000039MP3 PBC

CD PLAYER

POWER AMP

POWER AMP

EFFECT PROCESSOR

Ingresso Bilanciato

- Segnale

Schermatura + SegnaleINSERTS

SEND

RETURN

Ingresso microfonico bilanciato

PIN1: SchermaturaPIN2: + SEGNALEPIN3: - SEGNALE

Connessione cavi

Ingresso Sbilanciato Schermatura

+ Segnale

Schermatura

Connettore XLR Bilanciato

Massa

Massa

Connettore Jack Bilanciato

PAMX2. Series PAMX2. Series

PAGE 9PAGE 4

SYSTEM�BLOCK�DIAGRAMSCONTROL�PANELMono channel section

LOW CUT Switch:3Press this switch, can dacay the input signal under 75Hz.

LINE Input：

2This is a balanced/unbalanced jack for linking a line level source, input level range: -40~0dB

1 MIC InputThis is an XLR type connector for microphone, the input level range: -60~-20dB.This connector can offer +48V phantom power for condenser microphone when the phantom power switch is on.

GAIN:4Use this knob to adjust the level of the input signal to the optimal level. For the best balance of S/N ratio and dynamic range, adjust this knob so that the peak indicator 12 lights occasionally.

HI :5This knob control the frequency equalizer at higher frequency point.

Max adjust range： ±15dB @ 12KHz

MID:

6This knob control the frequency equalizer at middle frequency point.Max adjust range: ±15dB @ 2.5KHz

LOW:

7This knob control the frequency equalizer at lower frequency point.Max adjust range: ±15dB @ 80Hz

AUX:

8This knob is used for controlling the signal level feed to AUX bus, this control is set in front of the channel fader, so it’s not dependent on the fader position.

EFF:

9This knob is used for controlling the signal level feed to EFF bus, it has been set after the channel fader, so it is enslaved to the fader position. Adjust these knobs when you use effector on this channel.

10 PAN :

This konb is used for distributing the signal level of the channel feed to L/R buses. They are equal which are feed to bus when the knob locates in the middle .

11 CHANNEL FADER:This fader controls the output level feed to main bus from the input channel, adjusting the volume balance between channels. Faders of channels not in use should be pulled down.

12 PEAK Indicador:This red LED will warn you when an excessively high signal level is present in the channel. The signal is sampled at two points in the channel, immediately after/before the channel equalizer. The peak LED will illuminate approximately 6dB before clipping and therefore give warning of a possible overload.

13 PFL switch:This switch drive the signal to the head phones. The signal is sampled in front of the channel fader, so it has nothing to do with the fader position.

14 INSERT:The INSERT is a break point in the input channel signal path. It allows the signal to be taken out from the mixer, through an external equipment such as a compressor, and than back to the mixer to continue the final mix output.

PROFESSIONAL MIXER PROFESSIONAL MIXER

PAN

PAN

AUX

ON

+VPFL

PEAK

LOW

HIGH

EQ

BALANCE

ON

LOW

EQ

HIGH

EQ

AUX

+VPFL

L/MONO

LINE IN

R

-10dB

-20dB

TAPE IN L R

TAPE IN

-10dB

AUX RETURN

L/MONO

-10dB

R

REC OUT L R

ML MR

MAST

ER O

UT

DEPTH

REPEAT

ML

MR

PHONES

L

PFLC

RAUX

PFL

PHONE OUT

CH FADER

CH FADER

LEVEL

AUX SEND

MAIN L

+ +

+ +

LEVEL

+ +

++

+ +

7BAN

D GR

APHI

C EQ

7BAN

D GR

APHI

C EQ

PAD

ML MR MRMLLED DRIVER

+2 3

1

MAIN OUTPUT L

BALANCED

2 3

1

MAIN OUTPUT R

BALANCED

MAIN R

GAIN

INSE

RT

2 3

1

MIC

LIN

E

+48V

LOW CUT

MID

MID

MIC

LINE

3

4

1

2

5

6

7

9

12

13

11

8

10

14

15

15 ON:This switch include or exclude the channel from main output

EFF

EFF

EFF S

EN

D

EFF S

EN

D

EFF

PAMX2. Series PAMX2. Series

PAGE 5

CONTROL�PANEL

PAGE 8

2

The stereo channel1

This is the socket to connect the separate power suplly unit. .

POWER SOCKET:

Used for turn on/off the unit.

AC POWER SWITCH

PROFESSIONAL MIXER PROFESSIONAL MIXER

1 L left line input

These are two unbalanced connectors to which the left of a line level device can be connected. If signal is mono, pls connect only to L/Mono input

2 R Right line inputThese are two unbalanced connectors to which the right of a line level device can be connected, the rated input level is -10dB.

3 -10/ - 20 dB attenuation switchPress this knob, the input signal will be attenuated 20 dB. If unpressed the input signal will be attenauted 10 dB.

8 BAL：

This knob is used for controlling the stereo signal of the channel feed to L/R buses as some proportion to balance the stereo sound image.

HI :4This knob control the frequency equalizer at higher frequency point.

Max adjust range： ±15dB @ 12KHz

MID:

5This knob control the frequency equalizer at middle frequency point.Max adjust range: ±15dB @ 2.5KHz

LOW:

6This knob control the frequency equalizer at lower frequency point.Max adjust range: ±15dB @ 80Hz

AUX:

7Th knob used for controlling the signal level feed to AUX bus, this control is set in is is front of the channel fader, so not dependent on the fader position.it’s

10

CHANNEL FADER:This fader controls the output level feed to main bus from the input channel, adjusting the volume balance between channels. Faders of channels not in use should be pulled down.

9 PFL switch:

This switch allows you to monitor the signal of the input channel, the signal is sampled in front of the channel fader, so it has nothing to do with the fader position.

3

4

1

2

5

6

7

9

11

8

POWERAC 17.5Vx2

�TO�REDUCE�THE�RISK�OF�FIRE�OR�ELECTRIC�SHOCK�DO�NOT�EXPOSE�THIS�EQUIPMENT�TO��RAIN�OR�MOISTURE���

�

WARNING

RISK OF ELECTRIC SHOCKDO NOT OPEN

AVIS:�RISQUE�DE�CHOC�ELECTRIQUE������������NE�PAS�OUVRIR�

WARNING

0

1

1

2

1

2

REAR�PANEL

11

10

ON:This switch include or exclude the channel from main output

This knob used to control the input signal level from AUX IN sockets to main stereo bus and SUB

16 AUX IN:

CONTROL�PANEL

This double 7-segment LED display is used for indicating the work state of the inner effector, and the corresponding effect are shown as blow.

State display of inner effector: 9

These two buttons are used for selecting the

Buttons for choosing the state:

EFF SEND:12This knob is used for controlling the signal level feed to the inner effector from all input channels and also controlling the signal level output from the EFF SEND sockets.

EFF LEVEL:13This knob is used for controlling volume of the signal level from the output of the inner effector.

10

This LED is switched on when power is connectedPOWER LED:

PHONES volume control:This knob controls the volume of the headphones connected to the headphone jack.

18 Stereo L/R master control:These two slide faders are used for adjusting the final output level sent to the stereo output sockets.

15 Graphic equalizer:The 7-band stereo graphic equalizer can be used for sound quality adjustment.

14 Level meter for L and R output:This level meter indicates the signal level of the stereo main output (Left, Right and PFL).

This knob used to control the input signal level from TAPE IN sockets or MP3 player to main

17 TAPE IN - MP3 IN:

16

9

12

13

18

15

14

17

11

10

11

Effect List1 Delay 12 Delay 23 Flange4 Chorus5 Chorus/Room 26 Chorus/Room 17 Vocal Cancel8 Rotary Speaker

9 Plate 110 Room 311 Plate 212 Plate 313 Room 114 Room 215 Hall 116 Hall 2

19

19

PAMX2.82

PAMX2. Series PAMX2. Series

PAGE 7PAGE 6

CONTROL�PANEL

PROFESSIONAL MIXER PROFESSIONAL MIXER

1 REC OUT:These two RCA connectors can output low level stereo signal (left and right) for tape recorder.

3 MAIN OUT (L, R)These four connectors are all main output sockets of this mixer, two XLR connectors are balanced and two phone jacks are unbalanced.

4 Phantom Power Switch.+48V Phantom voltage will be added to the input connector on each microphone input channel when pressed this switch, it allows you using condenser microphone. All fader should be all the way down when switching on/off the Phantom power, in order to prevent excessive noise to stage monitor speakers and main speakers; Phantom powered Mics should not be plugged in with the +48V switched on. Never turn on the phantom power when you have line level source connected to the input connector of the microphone input channel.

PLAY IN:

2These two RCA connectors are unbalanced input for the play input signal, rate input level: -10dB.

6 EFF OUT ：

This is jack to send the output signals to the external effector.

AUX OUT:7

This is a stereo auxiliary output. This socket sends out the signal from AUX bus.

000039MP3 PBC

NO. TIME

CHANNEL 13/14 CHANNEL 15/16

000039MP3 PBC

MIC MIC MIC MIC

LINE LINE LINE LINE

1 2 3

6 78

5

4

USB port and MP3 player:

5

This USB jack allow to connect a USB pendrive. MP3 and WAV files can be managed by appropriate push buttons and all functions can be monitored by the display. MAIN OUT signal can be recordered on the USB pendrive

This knob used to control the input signal level from AUX IN sockets to main stereo bus and SUB group

16 AUX IN:

CONTROL�PANEL

This double 7-segment LED display is used for indicating the work state of the inner effector, and the corresponding effect are shown as blow.

State display of inner effector: 9

These two buttons are used for selecting the states

Buttons for choosing the state:

EFF SEND:12This knob is used for controlling the signal level feed to the inner effector from all input channels and also controlling the signal level output from the EFF SEND sockets.

EFF LEVEL:13This knob is used for controlling volume of the signal level from the output of the inner effector.

10

This LED is switched on when power is connectedPOWER LED:

PHONES volume control:This knob controls the volume of the headphones connected to the headphone jack.

18 Stereo L/R master control:These two slide faders are used for adjusting the final output level sent to the stereo output sockets.

15 Graphic equalizer:The 7-band stereo graphic equalizer can be used for sound quality adjustment.

14 Level meter for L and R output:This level meter indicates the signal level of the stereo main output (Left, Right and PFL).

This knob used to control the input signal level from TAPE IN sockets or MP3 player to main stereo bus

17 TAPE IN - MP3 IN:

11EFF

AUX IN:8

These are two auxiliary input unbalanced jacks. The rated input level is -10dB. They usually are used as the return input of the external effector, also can be used for other sources. If the source signal is mono, you should plug into the left channel socket only, thus the right output will be same as the left.

19

PAMX2. Series

COMPACT�MIXER

9

MONO OUT: (Models PAMX2.42 and PAMX2.122)9

10

MONO

9

12

13

14

11

16

18

15

17

19

MP 3

20

PAMX2.122 Effect list1 Delay 12 Delay 23 Flange4 Chorus

13 Room 114 Room 215 Hall 116 Hall 2

5 Chorus/Room 26 Chorus/Room 17 Vocal Cancel8 Rotary Speaker

9 Plate 110 Room 311 Plate 212 Plate 3

PAMX2.42 Effect list1 Live Room 12 Live Room 23 Live Room 34 Small Club 1

13 Cathedral 314 Large Hall 115 Large Hall 216 Large Hall 3

5 Small Club 26 Small Club 37 Small Hall 18 Small Hall 2

9 Cinema 110 Cinema 211 Cathedral 112 Cathedral 2

MONO OUT: 20

PAMX2. Series