PANEL ANTENNASWITH ONE LOW BAND ARRAY

4 | April 2015

SlimLine

SlimLineSeries

April 2015 | 5

Low visual impact multiband antennas. Engineered for very low windload while integrating 2G, 3G and 4G technologies in a compact package.

698-960 / 1695-2690 / 1695-2690 MHz

58803005880300A 5880300G 5880300DG

Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt

• Tri band antenna, dual polarisation, 6 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)

SlimLineLTE Ready

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5880300

Remote Electrical Tilt AISG1.1 5880300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5880300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5880300DG

Access Ports Description (Connectors)

The antenna has 6 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Ultra Wide Band Bottom System 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck

Ultra Wide Band Top System 1695-2690 MHz Ports (2x) 7/16-DIN Female Ultra Long Neck

Electrical Characteristics R1 Y1 (Bottom) Y2 (Top)

Frequency Bands (MHz) 700 800 900 1800 2100 2600 1800 2100 2600

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

15.515.515.2

16.516.416.2

17.417.317.0

17.117.117.1

17.517.517.4

18.018.017.8

17.117.117.1

17.517.517.4

18.018.017.8

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.5 < 1.5

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61° 65° 63° 61°

Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 7.0° 6.4° 5.2° 6.5° 5.9° 4.7°

Electrical Downtilt Range 0-10° 0-12° 0-12°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator (one per antenna)

Multi-Device Control Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.

Multi-Device Dual Unit (MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

R1

Y1

Y2

6 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2688 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 27 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 761 N Lateral: 348 N Rear: 747 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

698-960 / 1695-2690 / 1695-2690 MHz

58803005880300A 5880300G 5880300DG

Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt

Packaging

Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 32 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna

Dimensions (in mm)

Installation

RED 698-960 MHz

YELLOW 1695-2690 MHz

April 2015 | 7

790-960 / 1710-2170 / 1710-2170 MHz

58802005880200A 5880200G

Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt

• Tri band antenna, dual polarisation, 6 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

SlimLineSeries

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5880200

Remote Electrical Tilt AISG1.1 5880200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5880200G

Access Ports Description (Connectors)

The antenna has 6 colour-coded connectors located at the bottom face. See image on the following page.

RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck

WHITE Rings High Band (Top Array) 1710-2170 MHz Ports (Wide Band)Pattern Optimised for DCS1800 (2x) 7/16-DIN Female Ultra Long Neck

BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports (Wide Band)Pattern Optimised for UMTS2100 (2x) 7/16-DIN Female Long Neck

Electrical Characteristics Low Band (RED) High Band (WHITE) High Band (BLUE)

Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170 1710...1880 1900...2170

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

16.5...16.716.3...16.516.0...16.3

16.7...17.216.5...17.016.3...16.5

16.5...16.916.4...16.716.3...16.5

16.9...17.316.7...17.216.5...17.0

Input Impedance 50Ω 50Ω 50Ω

VSWR < 1.5 < 1.5 < 1.5

Polarisation ±45° ±45° ±45°

Horizontal Beamwidth (-3 dB) 72°...68°...65° 65° 62° 65° 62°

Vertical Beamwidth (-3 dB) 7° 7° 7° 7° 7°

Electrical Downtilt Range 0-10° 0-12° 0-12°

Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical 18 dB Typical

Front-to-Back Ratio > 25 dB > 25 dB > 25 dB

Maximum Power (Per Port) 200 W 160 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5880200A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5880200G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

8 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2690 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 24 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 160 km/h (EN1991-4-1) Frontal: 607 N Lateral: 510 N Rear: 944 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg

Wall mounting brackets with azimuth pan 0900183/00 1.6 kg

Wall mounting brackets with mechanical tilt and azimuth pan

0900885/00 3.3 kg

790-960 / 1710-2170 / 1710-2170 MHz

58802005880200A 5880200G

Tri Band | Panel Antenna | XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt

Packaging

Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 35 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 790-960 MHz

WHITE 1710-2170 MHz

BLUE 1710-2170 MHz

April 2015 | 9

698-960 / 1695-2690 MHz

58613005861300A 5861300G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt

• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10° / 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

SlimLineLTE Ready

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5861300

Remote Electrical Tilt AISG1.1 5861300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5861300G

Access Ports Description (Connectors)

The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Ultra Wide Band 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck

Electrical Characteristics R1 Y1

Frequency Bands (MHz) 700 800 900 1800 2100 2600

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

15.515.515.2

16.516.416.2

17.417.317.0

17.717.717.7

18.118.118.0

18.518.518.2

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61°

Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 6.1° 5.3° 4.2°

Electrical Downtilt Range 0-10° 0-10°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5861300A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5861300G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

R1

Y1

10 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2688 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 24 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 761 N Lateral: 348 N Rear: 747 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900393/00 5.1 kg

Brackets for pole 70 to 150 mm 0900501/00 5.8 kg

Kit to add mechanical tilt (0-10°) to above brackets

0900394/00 3.1 kg

Wall mounting brackets with azimuth pan 0900395/00 2.3 kg

Wall mounting brackets with mechanical tilt and azimuth pan

0900533/00 4.4 kg

698-960 / 1695-2690 MHz

58613005861300A 5861300G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt

Packaging

Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 28.5 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna

Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 698-960 MHz

YELLOW 1695-2690 MHz

April 2015 | 11

790-960 / 1710-2170 MHz

58612005861200A 5861200G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.9 dBi | Variable Tilt

• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10° / 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

SlimLineSeries

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5861200

Remote Electrical Tilt AISG1.1 5861200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5861200G

Access Ports Description (Connectors)

The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.

RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Long Neck

BLUE Rings High Band 1710-2170 MHz Ports (Wide Band) (2x) 7/16-DIN Long Neck

Electrical Characteristics Low Band (RED) High Band (BLUE)

Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

16.2...16.8...17.516.2...16.8...17.516.0...16.7...17.4

18.2...18.518.0...18.317.8...18.0

18.5...18.918.3...18.718.0...18.1

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 65° 65° 64°

Vertical Beamwidth (-3 dB) 7° 5° 4.5°

Electrical Downtilt Range 0-10° 0-10°

Isolation Between Ports > 25 dB > 30 dB, > 28 dB from 0° to 2° tilt

Isolation Between Bands 45 dB Typical 45 dB Typical

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio > 30 dB > 30 dB

Maximum Power (Per Port) 200 W 160 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5861200A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5861200G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

12 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2690 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 25 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 160 km/h Frontal: 580 N Lateral: 480 N Rear: 910 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt (0-10°) to above brackets

0900396/00 1.8 kg

Wall mounting brackets with azimuth pan 0900183/00 1.6 kg

Wall mounting brackets with mechanical tilt and azimuth pan

0900885/00 3.3 kg

790-960 / 1710-2170 MHz

58612005861200A 5861200G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 17.5 / 18.9 dBi | Variable Tilt

Packaging

Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 33 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 790-960 MHz

BLUE 1710-2170 MHz

April 2015 | 13

790-960 MHz

58202005820200A 5820200G

Single Band | Panel Antenna | X-Pol | 65° | 17.5 dBi | Variable Tilt

• Single band antenna, dual polarisation, 2 connectors • Variable electrical tilt 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • RET module fully inserted inside the antenna (field replaceable)

SlimLineSeries

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5820200

Remote Electrical Tilt AISG1.1 5820200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5820200G

Access Ports Description (Connectors)

The antenna has 2 connectors located at the bottom face. See image on the following page.

RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Electrical Characteristics

Frequency Bands (MHz) 790...880...960

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 72°...68°...65°

Vertical Beamwidth (-3 dB) 7°

Electrical Downtilt Range 0-10°

Isolation Between Ports > 25...30...30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical

Front-to-Back Ratio > 30 dB

Maximum Power (Per Port) 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5820200A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5820200G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

14 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 2688 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 17 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 160 km/h 600 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900188/00 1.5 kg

Wall mounting brackets with azimuth pan 0900183/00 1.6 kg

Wall mounting brackets with mechanical tilt and azimuth pan

0900885/00 3.3 kg

790-960 MHz

58202005820200A 5820200G

Single Band | Panel Antenna | X-Pol | 65° | 17.5 dBi | Variable Tilt

Packaging

Carton Box 2.93 x 0.35 x 0.24 m 0.246 m3 | 25 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 790-960 MHz

April 2015 | 15

698-960 / 1695-2690 MHz

58633005863300A 5863300G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt

• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10° / 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

SlimLineLTE Ready

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5863300

Remote Electrical Tilt AISG1.1 5863300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5863300G

Access Ports Description (Connectors)

The antenna has 6 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Ultra Wide Band 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck

Electrical Characteristics R1 Y1

Frequency Bands (MHz) 700 800 900 1800 2100 2600

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

14.514.514.2

15.515.415.1

16.416.316.0

17.717.717.7

18.118.118.0

18.518.518.2

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61°

Vertical Beamwidth (-3 dB) 12° 10° 9.4° 6.1° 5.3° 4.2°

Electrical Downtilt Range 0-10° 0-10°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5863300A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5863300G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

R1

Y1

16 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 1914 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 17 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 542 N Lateral: 248 N Rear: 532 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900393/00 5.1 kg

Brackets for pole 70 to 150 mm 0900501/00 5.8 kg

Kit to add mechanical tilt (0-10°) to above brackets

0900394/00 3.1 kg

Wall mounting brackets with azimuth pan 0900395/00 2.3 kg

Wall mounting brackets with mechanical tilt and azimuth pan

0900533/00 4.4 kg

698-960 / 1695-2690 MHz

58633005863300A 5863300G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt

Packaging

Carton Box 2.12 x 0.35 x 0.24 m 0.178 m3 | 21.5 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCUfor RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna

Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 698-960 MHz

YELLOW 1695-2690 MHz

April 2015 | 17

790-960 MHz

58182005818200A 5818200G

Single Band | Panel Antenna | X-Pol | 65° | 16.5 dBi | Variable Tilt

• Single band antenna, dual polarisation, 2 connectors • Variable electrical tilt 0-10°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • RET module fully inserted inside the antenna (field replaceable)

SlimLineSeries

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5818200

Remote Electrical Tilt AISG1.1 5818200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5818200G

Access Ports Description (Connectors)

The antenna has 2 connectors located at the bottom face. See image on the following page.

RED Rings Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Electrical Characteristics

Frequency Bands (MHz) 790...880...960

Gain (dBi)Tilt 0°Tilt 5°Tilt 10°

15.5...16.0...16.515.5...16.0...16.515.4...15.9...16.4

Input Impedance 50Ω

VSWR < 1.5

Polarisation ±45°

Horizontal Beamwidth (-3 dB) 72°...68°...65°

Vertical Beamwidth (-3 dB) 9°

Electrical Downtilt Range 0-10°

Isolation Between Ports > 25...30...30 dB

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical

Front-to-Back Ratio > 25 dB

Maximum Power (Per Port) 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5818200A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5818200G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

18 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 1910 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 13 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 413 N Lateral: 347 N Rear: 649 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900181/00 3.4 kg

Brackets for pole 70 to 150 mm 0900182/00 3.9 kg

Kit to add mechanical tilt to above brackets 0900188/00 1.5 kg

Wall mounting brackets with azimuth pan 0900183/00 1.6 kg

Wall mounting brackets with mechanical tilt and azimuth pan

0900885/00 3.3 kg

790-960 MHz

58182005818200A 5818200G

Single Band | Panel Antenna | X-Pol | 65° | 16.5 dBi | Variable Tilt

Packaging

Carton Box 2.13 x 0.35 x 0.24 m 0.180 m3 | 20 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 790-960 MHz

April 2015 | 19

698-960 / 1695-2690 MHz

58293005829300A 5829300G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 15.0 / 18.0 dBi | Variable Tilt

• Dual band antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-12° / 0-12°• SlimLine profile for low wind load • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)

SlimLineLTE Ready

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Ordering Options Model Number

Manual Electrical Tilt 5829300

Remote Electrical Tilt AISG1.1 5829300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5829300G

Access Ports Description (Connectors)

The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.

Ultra Low Band 698-960 MHz Ports (2x) 7/16-DIN Female Long Neck

Ultra Wide Band 1695-2690 MHz Ports (2x) 7/16-DIN Female Long Neck

Electrical Characteristics R1 Y1

Frequency Bands (MHz) 700 800 900 1800 2100 2600

Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value

13.013.012.8

14.013.913.6

14.914.814.5

17.117.117.1

17.517.517.4

18.018.017.8

Input Impedance 50Ω 50Ω

VSWR < 1.5 < 1.5

Polarisation ±45° ±45°

Horizontal Beamwidth (-3 dB) 73° 65° 65° 65° 63° 61°

Vertical Beamwidth (-3 dB) 16.8° 14.0° 13.2° 7.0° 6.4° 5.2°

Electrical Downtilt Range 0-12° 0-12°

Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt

Upper Sidelobe Rejection(20° sector above main beam)

18 dB Typical 18 dB Typical

Front-to-Back Ratio

@ 180°@ 180° ±30°

> 30 dB> 25 dB

> 30 dB> 25 dB

Maximum Power (Per Port) 250 W 200 W

Intermodulation3rd Order for 2x20W Carriers

< -110 dBm < -110 dBm

Electrical Downtilt Control

Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).

Manual Electrical Tilt (MET) Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET) Control

The remote control of the electrical tilt is managed by a Multi-Device Control Unit (MDCU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).

RET Module Part Number(one per antenna)

MDCU-A0000 for AISG1.1 protocol (one unit included in 5829300A)

MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5829300G)

Environmental

Operating Temperature Range -40° C to +60° C

Environmental ETS 300 019

RoHS Compliant Yes

R1

Y1

20 | April 2015

Mechanical Characteristics

Dimensions (Height x Width x Depth) 1358 x 253 x 147 mm

Weight (Excluding Mounting Accessories) 13 kg

Shroud Outdoor Plastic, Grey RAL7035

Wind Speed Operational: 160 km/hr Survival: 200 km/h

Wind Load at 150 km/h Frontal: 385 N Lateral: 176 N Rear: 378 N

Mounting Kit Options Part Number Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.

Brackets for pole 48 to 115 mm 0900393/00 5.1 kg

Brackets for pole 70 to 150 mm 0900501/00 5.8 kg

Kit to add mechanical tilt (0-10°) to above brackets

0900394/00 3.1 kg

Wall mounting brackets with azimuth pan 0900395/00 2.3 kg

Wall mounting brackets with mechanical tilt and azimuth pan

0900533/00 4.4 kg

698-960 / 1695-2690 MHz

58293005829300A 5829300G

Dual Band | Panel Antenna | XX-Pol | 65° / 65° | 15.0 / 18.0 dBi | Variable Tilt

Packaging

Carton Box 1.57 x 0.35 x 0.24 m 0.132 m3 | 17.5 kg

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

Location of the MDCU or MDDU for RET Control

Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.

Bottom View of Antenna

Dimensions (in mm)

In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.

Always attach the antenna by the two mounting points.

Do no install the antenna with the connectors facing upward.

Installation

RED 698-960 MHz

YELLOW 1695-2690 MHz

April 2015 | 21