part design (drawing 06) - weebly
TRANSCRIPT
![Page 1: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/1.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
PART DESIGN (DRAWING 06)
From this diagram we have to know,
Selection of plane
Drawing circle
Drawing rectangle
Pad the profile
Pocket definition
Offset plane
Symmetry constraint
Trimming
Object mirror
Chamfer
Fillet
Rotate options
Views
CATIA v5 software is used to modeling this object.
Prepared By
Veerapandian.K Mechanical Engineering.
![Page 2: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/2.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
![Page 3: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/3.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
**WORKING STEPS**
Draw rectangle with dimensions.
Pad this with given dimensions.
![Page 4: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/4.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Draw a circle. Locate this on position.
Pad this circle with mirror extend option.
![Page 5: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/5.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Sketch rectangle as below pad this.
Again draw a rectangle at following place then pocket this.
![Page 6: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/6.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Draw like this.
Give dimensions. Draw circle edit this with trim tool.
![Page 7: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/7.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Pad the sketch.
Draw sketch like this.
![Page 8: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/8.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Pad this sketch.
After pad diagram displays like this.
![Page 9: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/9.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Draw circle then pad the circle.
Make hole inside the cylinder body.
![Page 10: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/10.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Make a hole with hole definition option.
Mirror the object shown in diagram.
![Page 11: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/11.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
Define edge fillet.
Define edge fillet.
![Page 12: PART DESIGN (DRAWING 06) - Weebly](https://reader031.vdocuments.net/reader031/viewer/2022022406/6216b50d5345781dee5b6fe9/html5/thumbnails/12.jpg)
Veerapandian.K MECHANICAL ENGINEERING, SRVEC, VEDARANYAM.
After completion the diagrams being like this.
Completed diagram.
Pandian.K