paso

iPASOLINK 200 LCT iPASOLINK 200 LCT 11TOPC-E4011E-02- ＸＸＸＸＸＸ

iPASOLINK LCT WEBiPASOLINK LCT WEB

Basic Radio, TDM and Ethernet Basic Radio, TDM and Ethernet ProvisioningProvisioning

Provided for Training Sep 2010

Note: The LCT screen shots shown in this document might not be identical to the ones actually observed on LCT.


ContentsContents

1. Introduction to LCT & Connection

2. Equipment Setup & Provisioning of Main Radio Parameters

3. Activation of TDM Services

4. Basic Maintenance Operations for Radio & TDM Portion

5. Management Network Settings for activation of Remote LCT

6. Activation of Basic Ethernet Services

TOPC-E4011E-02- ＸＸＸＸＸＸ

Chapter 1Chapter 1

Introduction to LCT & Connection


LCT Connection Port & PC RequirementsLCT Connection Port & PC Requirements

THE LOCAL CRAFT TERMINAL IS USED TO SETUP, MONITOR AND MAINTAIN iPASOLINK RADIO. iPASOLINK SUPPLIES USER`S GUI ENVIRONMENT THROUGH WEB BROWSER. LCT SUPPORTS

BOTH LOCAL AND REMOTE CONNECTIONS

WINDOWS XP WINDOWS VISTA & WINDOWS 7

CPU PENTIUM-M 1.6GHz OR BETTER INTEL CORE2 DUO 1.6 GHz

RAM 512MB OR MORE 1 GB

HDD 40 GB OR MORE FREE CAPACITY 40 GB OR MORE FREE CAPACITY

DISPLAY COLOR LCD (1024x768) COLOR LCD (1024x768)

LAN PORT

10/100 Base T(X) 10/100 Base T(X)

SOFTWARE REQUIREMENT

OS WIN DOWS XP (ENGLISH VERSION)

WINDOWS VISTA (ENGLISH VERSION)

WINDOWS 7 (ENGLISH VERSION)

IE8, IE7, FIREFOX3.6 OR HIGHER

COMMUNICATION BETWEEN THE LCT AND THE iPASOLINK IS VIA THE LCT PORT OF IDU. CONNECTION IS BY LAN CABLE.


LCT COMMUNICATION INTERFACELCT COMMUNICATION INTERFACE

IP Settings in PC:

Set IP Address Auto Assign

LCT Port supports DHCP. Default IP Address is

172.17.254.253


LCT Startup & LoginLCT Startup & Login

Start your Browser

User Name Password Privilege group Comment

Admin ADMIN Status View, Provisioning, System Administration

Config CONFIG Status View & Provisioning

User OPERATOR Status View only

http://172.17.254.253/


Intial Screen (Example)Intial Screen (Example)

LCT Menus

Always logout by

this button

Active alarms & Current Status


LCT Main MenusLCT Main Menus

Expand and observe available Menus


Chapter 2Chapter 2

Equipment Setup & Provisioning of Main Radio Parameters


EQUIPMENT SETUP - EQUIPMENT EQUIPMENT SETUP - EQUIPMENT CONFIGURATIONCONFIGURATION

See details in next pages


EQUIPMENT CONFIGURATIONEQUIPMENT CONFIGURATION

Equipment Name

Equipment Configuration shows the mounted option boards.

Modem SW/XPIC GRP Configuration shows the how the Modem 1 and 2 are used.

Connected ODU information and IDU

(Modem) Settings

Adaptive Modulation Radio Settings


EQUIPMENT CONFIGURATION – Setup (1)EQUIPMENT CONFIGURATION – Setup (1)

Click on the Setup Icon to open the setup 1 Setting of Equipment Name window.

1

1

Left side shows the current setting. Click on the Equipment Name field in the New setting in the right hand of the window. And enter the new name. (up to 32 characters)

If you exceed the number of characters, the entry field border turns to red and when the cursor is moved to the entry field pop will show the limits

2 Click on the Next Button to go to next setting window. If the name field characters exceed, Input Error warning popup appears.

2

Setting of SW/XPIC Group window allows setting of how the two modems are used. For (1+1) configuration click on the check box SW/XPIC GRP and click on the drop down arrow and select the required option. Other wise click on modem 1 or modem 2 and select used or not used.

3

3 Click the Next button to go to the next setting window


EQUIPMENT CONFIGURATION – Setup (2)EQUIPMENT CONFIGURATION – Setup (2)

Modifications to be applied are highlighted


EQUIPMENT SETUP – RADIO CONFIGURATIONEQUIPMENT SETUP – RADIO CONFIGURATION



RADIO CONFIGURATION -Setup (1)RADIO CONFIGURATION -Setup (1)

Click the Equipment Setup Menu and select Radio Configuration to open the Equipment Setup – Radio configuration window.

Selected modem

Specification and information of the ODU connected to the selected Modem

Current setup of the modem radio configuration

Select the channel spacing of the radio signal

Select the reference Modulation of the radio signal

Radio Mode: select High capacity or High system Gain. High system gain is achieved by better FEC.

Select the number of E1 channels to be used

Select the number of STM-1 channels to be used (need STM-1 optional Interface card (one STM-1)

Show the available Ether bandwidth after E1 and STM-1 traffic.

Select the TX Power Control Mode. ATPC or MTPC. Parameter setting for each mode is from provisioning menu Enter the radio signal Frame ID (1 ~ 32)

Enter TX/RX point frequency within the Start and Stop frequency of the ODU shown above.


RADIO CONFIGURATION – Setup (2)RADIO CONFIGURATION – Setup (2)

Changes are applied


EQUIPMENT SETUP – AMR CONFIGURATIONEQUIPMENT SETUP – AMR CONFIGURATION



AMR CONFIGURATION – Setup (1)AMR CONFIGURATION – Setup (1)

Setup for Modem1

AMR Operation Settings

E1/STM-1 Mapping Settings:

Priorities for preservation of traffic (E1/STM1/Ethernet) as modulation level (and therefore transmission

capacity) decreases

See next page


AMR CONFIGURATION – Setup (2)AMR CONFIGURATION – Setup (2)

Changes are applied

Setup for Modem2


Main Provisioning Menus (Radio & TDM)Main Provisioning Menus (Radio & TDM)


PROV – MODEM - Modem Port SettingPROV – MODEM - Modem Port Setting


PROV – MODEM - Radio Switch SettingPROV – MODEM - Radio Switch Setting

Only for systems with 2 enabled Modems in 1+1 Redundancy Configuration.

Example:

Example:

Example:


PROV - MODEM – TX Power SettingPROV - MODEM – TX Power Setting


PROV - MODEM – ALARM MODE SETTINGPROV - MODEM – ALARM MODE SETTING

Example case Hot Standby


PROV - MODEM – BER THRESHOLD SETTINGPROV - MODEM – BER THRESHOLD SETTING


PROV – EQPT CLK/SYNC – Equipment ClockPROV – EQPT CLK/SYNC – Equipment Clock


PROV – V.11/OW - OW SettingPROV – V.11/OW - OW Setting


Chapter 3Chapter 3

Activation of TDM Services


PROV – E1/STM1/XC – STM1 Port Setting (1)PROV – E1/STM1/XC – STM1 Port Setting (1)


NOTE: Optional STM-1 Board is required


PROV – E1/STM1/XC – STM1 Port Setting (2)PROV – E1/STM1/XC – STM1 Port Setting (2)

Example:



PROV – E1/STM1/XC – E1 Port SettingPROV – E1/STM1/XC – E1 Port Setting

Example:


PROV – E1/STM1/XC – Cross Connect SettingPROV – E1/STM1/XC – Cross Connect Setting


Chapter 4Chapter 4

Basic Maintenance Operations for Radio & TDM Portion


Metering – Current MeteringMetering – Current Metering


Maintenance Control – Loopback Control Maintenance Control – Loopback Control MenusMenus

Case of Modem Loopback:


Maintenance Operations – Maintenance ModeMaintenance Operations – Maintenance Mode

Must shift to MAINT mode before executing any

Maintenance Operation


MAINT Control- Modem LoopbackMAINT Control- Modem Loopback

If not in MAINT mode:


MAINT Control- TDM Loopback1MAINT Control- TDM Loopback1


MAINT Control- TDM Loopback2MAINT Control- TDM Loopback2


MAINT Control - STM-1 Loopback1MAINT Control - STM-1 Loopback1



MAINT Control- STM-1 Loopback2MAINT Control- STM-1 Loopback2



INVENTORY(1)INVENTORY(1)

Example for IDU:


INVENTORY(2)INVENTORY(2)

Example for ODU:


Software License InformationSoftware License Information

Example:


Chapter 5Chapter 5

Management Network Settings for Activation of Remote LCT


Network Management Configuration MenusNetwork Management Configuration Menus


Network Management – General SettingNetwork Management – General Setting

Example:


Network Management – General Setting DetailNetwork Management – General Setting Detail

Example:


Network Management – Route SettingNetwork Management – Route Setting

Example:

For addition of Static Routes whenever required


Example for setting on Local & Remote EndsExample for setting on Local & Remote Ends

PC for Remote LCT

NMS Port

Management LAN

254


Connection via NMS Port & LCT AccessConnection via NMS Port & LCT Access

Browse local IP Address: http://192.168.1.10/

Browse Remote IP Address: http://192.168.1.20/


Chapter 6Chapter 6

Activation of Basic Ethernet Services


Ethernet Service Provisioning Main MenusEthernet Service Provisioning Main Menus


ETH Function Setting - Bridge SettingETH Function Setting - Bridge Setting

Example:


ETH Function Setting – ETH Port SettingETH Function Setting – ETH Port Setting

Example:

It is a good practice to disable unused ports


ETH Function Setting – VLAN Setting – Add ETH Function Setting – VLAN Setting – Add VLANVLAN

Add first required VLAN IDs on VLAN List:

Example:

Example:


VLAN Setting – Assign ports to VLAN IDVLAN Setting – Assign ports to VLAN ID


Example of Modem PortExample of Modem Port

Modem port is always Trunk (tagged frames only)

Modem port transports the VLAN IDs enabled here. In this example, only tagged frames belonging to VLAN ID = 2, 10, 20 or 30 are

processed on this Modem1 port.


Example of Access Port (Untagged Frames Example of Access Port (Untagged Frames only)only)

Only Untagged frames are processed on Port 2, and

these frames are assumed to belong to VLAN ID = 10

P1 (FE)

Fm A

to C

MSGVLAN x

Fm A

to B

MSGVLAN 10

Fm A

to B

MSG


Example of Trunk Port (tag/untag Frames)Example of Trunk Port (tag/untag Frames)

Untagged frames on Port 2 are assumed to belong to VLAN ID = 2Tagged frames on

Port 2 must have VLAN ID = 20

P2 (FE)

Fm A

to B

MSG

Fm A

to C

MSGVLAN 20

Fm A

to C

MSGVLAN 20

Fm A

to B

MSGVLAN 2

Fm A

to C

MSGVLAN other


Example of Tunnel Port (Any Frame Example of Tunnel Port (Any Frame Forwarding)Forwarding)

Any frame type on Port 3, either untagged or tagged with any VLAN ID, will be unconditionally tagged (Outer Tag) with VLAN ID = 30 and

then processed.

P3 (FE)

Fm A

to B

MSG

Fm A

to C

MSG1VLAN any

Fm A

to B

MSGVLAN 30

Fm A

to C

MSG1VLAN 30

VLAN any


Summary of VLAN Setting in previous Summary of VLAN Setting in previous examplesexamples


Ethernet Services Registration and DeletionEthernet Services Registration and Deletion

Registration

Register VLAN ID

(Add VLAN)

Assign ports to newly added VLAN ID

(Assign VLAN ID)

End

Deletion

Delete VLAN ID

Remove ports from VLAN ID to be deleted

(Assign VLAN ID – VLAN Assignment Clear)

End

Click

Uncheck


Thank youThank you

Note: The LCT screen shots shown in this document might not be identical to the ones actually observed on LCT.

paso

Documents