pattern book vol. 1 from primabead.com

13 FREE PATTERNS INSIDE RECEIVE A FREE GIFT WITH YOUR PURCHASE

Your coupon code is located on the back cover

$25only

PATTERN BOOK • VOLUME 1

800-366-2218 • WWW.PRIMABEAD.COM • FREE SHIPPING

shimmerClass In A Box • 1,840 pcsBead Mat & 3-in-1 Tool IncludedMakes 2 Necklaces, 2 Bracelets & 2 Sets of Earrings

34706012

.COM

Free Shipping . 10-25% Volume Discounts . Free Patterns2

Tools Needed: Needle Nose Pliers #4454Crimping Pliers #4501 Wire Cutters #4457

Techniques to Know: Opening Jump Rings Crimp Tubes

Bethanynecklace

3

Instructions: 1. Cut the following lengths of beading

wire: a 7”, a 9” and an 11” length.

2. Using crimp tubes, attach each wire

to its own 4mm jump ring.

3. Thread the following pattern onto the 7” wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.

4. Thread the following pattern onto the 9” wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.

5. Thread the following pattern onto the 11” wire: a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval, a bicone, a purple hexagon, a bicone, a white oval and a bicone.

6. Using crimp tubes, attach each wire to its own 4mm jump ring. Trim the excess wire.

7. Cut (12) 8” lengths of chain.

8. Attach (2) chains to each 4mm jump ring.

9. Gather a set of chains from one end of each beaded section using a 6mm jump ring. Attach a toggle clasp to the jump ring.

10. Repeat the steps for the other set of chains and clasp.

Materials:# 34713130

4mm Bronze Metallic Bicones (1pk)

$4.00

# 37450085 Purple/White Shell Bead Strand (3pks)

$4.00

# 34718104 Copper Small Chain (2pks)

$4.00

# 34719069 Copper Findings Pack (1pk)

$4.00

# 3202001 Gold 7-Strand Beading Wire (1pk)

$2.00

Shop now at www.primabead.com/bethany


Blue Icecoin knot earrings


Silver Satin Cord (1 pk)

$3.99

# 34745020 Blue Metallic Cord (1 pk)

$3.99

# 34712124 Silver Cord Ends (1 pk)

$1.99

# 34712100 Silver Earring Wires (1 pk)

$2.00

Makes16 pairs

5

Instructions: 1. Cut (2) 16” lengths of metallic blue cord and

(1) 16” length of silver cord.

2. Weave the cords as a set, with silver cord on the inside. Follow the pattern as shown on our website.

3. Shift the cords to make the knot tighter and more even.

4. Bring the ends together and trim the excess.

5. Use a metal cord end to secure the cords together. Attach the earring wire to the hole of the cord end.

6. Repeat steps 1-5 for the matching earring.

Tools Needed: Needle Nose Pliers #4454Wire Cutters #4457

Techniques to Know: Opening Jump RingsCord Ends

Shop now at www.primabead.com/blueice


Tools Needed: Round Nose Pliers #6858Wire Cutters #4457

Techniquesto Know: Wire Wrapping

Gemstone cuffbracelet


Gold Cuff Bracelet (1 pc)

$2.00

# 34714124 Green Agate Slice (1 pc)

$2.00

# 3201801 Gold 24 Gauge Wire (1 pk)

$2.69

# 22279001 E6000® Glue (1 tube)

$3.40

Instructions: 1. Use E6000® to adhere the accent to

the top center of the cuff. Allow the adhesive to dry thoroughly (according to manufacturers instructions) before adding the wire to prevent the agate from sliding on the cuff.

2. Cut a 36” length of gold wire.

3. Tuck one end of the wire between the gemstone and the cuff. Wrap the wire multiple times around the base of the gemstone.

4. Bring the wire up over the stone and down to one side and under the cuff, keeping the wire snug against the cuff. Continue wrapping the wire over the stone and under the cuff.

5. Tuck the end of the wire under the lip of the gemstone but not on the inside of the cuff. Apply additional adhesive to keep the wire in place.

6. Using round nose pliers, gently twist the wire along the top of the gemstone. The slight twisting tightens the wire on the gemstone.

7Shop now at www.primabead.com/gemstone


Instructions: 1. Cut (4) 50” lengths of blue metallic cord.

2. Bring the cord ends together and fold in half. Bring the fold down through the center of the round disc.

3. Cut a scrap piece of cord (4+ inches) and tie it onto the center fold from step 2.

4. Align the cords as explained in the “Beaded Kumihimo” instruction booklet that came with the round disc.


Metallic Blue Cord (1 pk)

$3.99

# 34745036 Kumihimo Bobbins (1 pk)

$6.99

# 34745001 Metallic Blue Rondelles (1 pk)

$11.99

# 34745033 Kumihimo Round Disc (1 pc)

$2.99

# 34750022 Silver Kumihimo Findings Pack (1 pk)

$3.99

# 34745035 Kumihimo Beading Needle (1 pc)

$2.99

# 22279001 E6000® Glue (1 tube)

$3.40

5. Using the big eye beading needle, thread (30) metallic beads onto each strand. This makes an 8” bracelet with cord ends. Use less or more beads on each of the eight cords to decrease or increase the overall length.

6. Wind each of the eight cords (with beads) onto a bobbin and close.

7. Follow the beaded instructions that came with the disc. Braid the cord ½” before adding the beads. This section will be inserted into the clasp.

8. Braid a ¼” tail after all of the beads have been braided in. Remove the cords from the bobbins and from the disc and tie them into a tight single knot. Remove the scrap cord from the other end.

9. Trim the excess cord. Next apply glue to the ends of the cords and slide the cord ends on. Allow the glue to dry according to manufacturer instructions (2+ hours).

Tools Needed: Round Nose Pliers #6858Needle Nose Pliers #4454Wire Cutters #4457

Techniques to Know: Kumihimo Round Braiding w/ Beads

9

Blue Iriskumihimo bracelet

Shop now at www.primabead.com/blueiris


Francescabracelet

DRESS LIKE IT.~Lilly Pulitzer

“ “Life’s a party,

11

Instructions: 1. Cut (or separate using two pairs of pliers) the

large double link chain into a 6 ½” section.

2. Attach (2) 6mm jump rings to each end of the chain.

3. Using 6mm jump rings, attach a lobster claw clasp to one set of jump rings and attach an extender chain to the other set of jump rings.

4. Make a wrapped loop bicone drop and attach the drop to the end of the extender chain.

5. Cut (2) 10” lengths of beading wire.

6. Using crimp tubes, attach each wire to a 6mm jump ring at one end of the double link chain.

7. Thread (44) bicones onto each wire.

8. Weave the bicone strands through the chain links.

9. Using crimp tubes, attach the beading wire strands to the 6mm jump rings at the end of the chain. If it’s too difficult to weave the loose strands of beads, try crimping the wire, leaving a small loop for the jump ring to fit though. Then weave the strands through the double link chain.


4mm Bicone Mix (2 pks)

$4.00

# 34718096 Silver Large Double Link Chain (1 pk)

$4.00

# 34719059 Silver Findings Starter Pack (1 pk)

$4.00

# 3202002 Silver 7-Strand Beading Wire (1 pk)

$2.00

Tools Needed: Round Nose Pliers #6858Needle Nose Pliers #4454Crimping Pliers #4501Wire Cutters #4457

Techniques to Know: Opening Jump RingsForm a Wrapped Loop

Crimp Tubes

Shop now at www.primabead.com/francesca


CREATIVITY““is an act of defiance.

~Twyla Tharp

13

Instructions: 1. Using pliers, separate the chain into (28) 10-link lengths, each approximately 1 ½” long.

2. Cut (4) 14” lengths of stretch cord. Lay the (4) cords flat in a row, approximately ½” from each other.

3. Thread each cord through a single chain and thread a turquoise round onto cords 1 and 3.

4. Thread each cord through a single chain and thread a turquoise round onto cords 2 and 4.

5. Repeat steps 3-4 14 more times. Increase the overall length by repeating steps 3-4 again.

6. Tie each cord together into a double knot. Trim the excess cords. The tension of the stretch cord will move the chain so it surrounds the beads and forms a woven pattern.


Gold Small Curb Chain (2 pks)

$4.00

# 34713033 8mm Turquoise Round Beads (1 pk)

$4.00

# 3202302 .8mm Stretch Cord (1 pk)

$2.00

Caprisebracelet

Tools Needed: Needle Nose Pliers #4454Wire Cutters #4457

Techniques to Know: Tying a KnotOpening Jump Rings

Shop now at www.primabead.com/caprise


Triple Cabochon Bracelet Instructions:1. Apply dabs of Quick Hold® glue to a set

of round bezels and attach them to the back of an oval cabochon. Do not let the glue seep through the opening for the flat memory wire, otherwise, once the glue dries it won’t allow the wire to fit. Repeat this step for the remaining two cabochons.

2. Allow the glue to dry completely before continuing the bracelet.

3. Cut (2) single coils of bracelet memory wire.

4. Slide each cabochon onto the set of wires and position them at the center.

5. Cut a 48” length of gauge wire.

6. Coil the wire onto the memory wire to the inner side of the end cabochon bezel. Coil the wire approximately (5) loops and press the coil snug. Bring the wire over the back side of the bezel and continue to coil it onto the memory wire.

Additional Patterns Available Online @ www.primabead.com/crackle

Tools Needed: Round Nose Pliers #6858Parrot Beak Pliers #4477Wire Cutters #4457

Techniques to Know: Wire Wrapping


Gold Flat Bracelet Memory Wire (1 pk)

$3.99

# 74100061 Gold Flat Memory Wire Ends (1 pk)

$2.99

# 74100068 Gold Flat Memory Wire Round Bezels (1 pk)

$2.99

# 3201801 Gold 24 Gauge Wire (1 pk)

$2.69

# 22279004 Quick Hold® & E6000® Mini Tubes (1pk)

$4.00

# 9161 Gemocite Cabochon Mix (1 pk)

$8.00

7. Coil the wire up to the bezel of the center cabochon. The sample has 1/2” of coil between each bezel. Bring the wire over the back side of the bezel and continue the coil. Repeat this step until the wire is coiled into (5) loops after the last cabochon.

8. Repeat steps 5-7 to secure the second memory wire section.

9. Size the bracelet and trim 1/2” off the total size needed for each memory wire length.

10. Using E6000®, adhere the wire ends to the memory wire and allow the adhesive to dry thoroughly.

15

Crackle Cabochon

jewelry

Shop now at www.primabead.com/crackle


The constant happiness is

CURIOSITY.~Alice Munro

“ “

Makes2 bracelets

17

Large Flower Bracelet Instructions:1. Remove the chains, jump rings and

charms from the large flower. *These pieces will be used in the adjustable bracelet.

2. Cut a single coil of bracelet memory wire.

3. Form a loop to one side of the wire. Attach the smaller of the flower loops to the wire.

4. Form a partial loop at the other end of the wire, this should fit into the large loop of the flower. If the bracelet is too large, trim off a small section and form another loop.

Adjustable Flower Bracelet Instructions:1. Cut a 1 1/2 coil of bracelet memory wire,

approximately 12” in length.

2. Form a loop at each end of the wire.

3. Bend each loop inwards and overlap the loops over the opposite ends of the wire, making the bracelets adjustable.

4. Using the jump rings from the accent, attach the three charms to the bracelet.

Tools Needed: Round Nose Pliers #6858P arrot Beak Pliers #4477

*Used for Memory Wire

Techniquesto Know: Form a Loop


Gold Flat Memory Wire (1 pk)

$3.99

# 72099305 Gold Flower Cluster Pendant (1 pc)

$5.99

Golden FlowerCharmbracelets

Shop now at www.primabead.com/goldenflower


Tools Needed: Needle Nose Pliers # 4454Wire Cutters # 4457Crimping Pliers # 4501

Techniquesto Know: Opening Jump RingsCrimp Tubes

Instructions:1. Cut (3) 10” lengths of beading wire.

2. Use a crimp tube to gather the (3) wires together and attach them to an 8mm jump ring. Connect a toggle clasp end to the same jump ring.

3. Thread each beading wire strand through the holes of a 3-strand rondelle.

4. Thread (3) blue bicones onto one of the end strands. Thread (2) blue bicones onto the middle strand. Thread (1) blue bicone onto the other end strand.

5. Thread (1) 3-strand spacer onto the beading wire strands.

6. Thread (1) mirror bead onto the strand containing (3) bicones. Thread (2) blue bicones onto the middle strand. Thread (3) mirror beads onto the strand containing (1) bicone.


8. Thread (3) blue pearls onto the strand with the single mirror bead and (3) crystals. Thread (2) blue pearls onto the strand with the (2) mirror beads and (2) crystals. Thread (1) blue pearl onto the strand with the (3) mirror beads and (1) crystal.


10. Continue the pattern of beads until the bracelet is at the desired length.

11. Use a crimp tube to gather the (3) wires together and attach them to an 8mm jump ring. Connect the other toggle clasp end to the same jump ring.


6mm Blue Pearl/Crystal Mix (1 pk)

$4.00

# 34741058 6mm Dark Blue Mirror Beads (1 pk)

$4.00

# 34719059 Silver Findings Starter Pack (1 pk)

$4.00

# 34708262 Silver & Crystal Rondelle Spacer (3 pks)

$4.00

# 34719057 Silver 8mm Jump Rings (1 pk)

$4.00

# 3202002 Silver 7-Strand Beading Wire (1 pk)

$2.00

19

Mollybracelet

Pattern Variations Available Online @ www.primabead.com/molly

Shop now at www.primabead.com/molly


SharedHearts

Tools Needed: Needle Nose Pliers #4454Round Nose Pliers #6858Crimping Pliers #4501

Techniques to Know: Forming a LoopOpening Jump RingsCutting Chains

bracelet & earrings

21


145pc Starter Pack Silver (1 pk)

$4.00

# 34708289 5pc Silver Deco Heart (1 pk)

$4.00

# 34718092 100 in/254cm Silver Small Curb Chain (1 pk)

$4.00

# 34722035 101 pc 6mm Pearl/Crystal Mix Red (1 pk)

$4.00

# 3202002 40’ .3mm 7-Strand Bead Wire- Silver (1 pk)

$2.00Instructions for Bracelet:1. Cut (10) 2 1/8” lengths of silver

chain. Approx. 27 links each

2. Take (5) lengths of the chain and connect each group of ends with a 2mm jump ring, then repeat with the other (5) lengths of chain.

3. Connect a 4mm jump ring to one side of each grouping of chains (this will be where you connect the toggle clasps).

4. Using the 4mm jump rings you just attached to the chain groups, connect the two ends of your toggle clasps.

5. Moving onto the center of the bracelet. Begin by cutting a 4” strand of beading wire.

6. Crimp a small loop into one end of the wire, leaving about 1” on one side and 3 inches on the other.

7. Thread the beads in this order onto the wire: bicone, heart, pearl, heart, bicone.

8. Close the other end of the wire into a loop using a crimp bead. (If you leave enough extra wire to feed back through the heart it will be easier to pull the wire and form a tighter loop).

9. Finally, connect either end of your hearts to the 2mm jump rings on the ends of your pieces from steps 1-4.

Instructions for Earrings:1. Cut (10) 1 ¼” lengths of chain. Approx. 19 links

each

2. Thread (5) lengths of chain onto a 2mm jump ring

3. Now connect the 2mm jump ring to the loop on an eye pin.

4. Thread a pearl and then a bicone onto the eye pin and create a loop on the end.

5. To make sure that your earrings hang correctly, you’ll need to connect a 2mm jump ring on the end of your eye pin before you connect the earring wires.

6. Now repeat steps 1-5 to make the matching earring.

Shop now at www.primabead.com/sharedhearts


Successis liking yourself, liking what you

do, and liking how you do it.~Maya Angelou

““

23

Tools Needed: Crimping Pliers #4501Wire Cutters #4457

Techniquesto Know: Crimp Tubes

Instructions:1. Cut (5) 12” lengths of stretch cord.

2. Using crimp tubes, attach each length of stretch cord to one end of the toggle. Use separate crimp tubes for each length of cord.

3. Thread (35) beads onto each length of stretch cord. Use less or more depending on the overall length needed.

4. Use crimp tubes to attach each length of cord to the other end of the toggle. Use separate crimp tubes for each length of cord.

5. Trim the excess cords.

TurquoiseDream

braceletMaterials:# 34719178

Cabochon Toggle (1 set)

$3.00

# 34741016 Turquoise Bicone Mirror Beads (3 pks)

$4.00

# 3202302 .8mm Stretch Cord (1 pk)

$2.00

# 34712131 Silver Crimp Tubes (1 pk)

$1.99

Shop now at www.primabead.com/turquoise

CU

RR

ENT

RES

IDEN

T (O

CC

UPA

NT)

OR

PR

ES

OR

TED

STA

ND

AR

DU

.S. P

OS

TAG

EPA

IDP

RIM

A B

EA

D12

333

EN

TER

PR

ISE

BLV

D.

LAR

GO

, FL

337

73

Ent

er c

ode

abov

e at

che

ckou

t fo

r a

FRE

E G

IFT

with

pur

chas

e!*C

oupo

n ca

n on

ly b

e re

deem

ed o

nce

per

cust

omer

.

CLA

SS I

N A

BO

XC

lass

ic#3

4706

-009

15

5+ p

iece

s!

Mak

es 2

Nec

klac

es,

2 B

race

lets

& 2

set

s of

Ear

rings

Bead

Mat

& 3

-in-1

To

ol In

clud

ed

$ 25

Cas

ual

#347

06-0

10

230+

pie

ces!

Mak

es 2

Nec

klac

es,

2 B

race

lets

& 2

set

s of

Ear

rings

Bead

Mat

& 3

-in-1

To

ol In

clud

ed

$ 25

Nat

ural

#347

06-0

11

255+

pie

ces!

Mak

es 2

Nec

klac

es,

2 B

race

lets

& 2

set

s of

Ear

rings

Bead

Mat

& 3

-in-1

To

ol In

clud

ed

$ 25

Let

us

help

you

CR

EATE

BEA

UTI

FUL

JEW

ELR

YO

RD

ER

ON

LIN

E

OV

ER

TH

E P

HO

NE

Our

qui

ck a

nd e

asy

chec

kout

pro

cess

m

akes

ord

erin

g a

bree

ze. P

lace

an

orde

r at

w

ww

.prim

abea

d.co

m 2

4 ho

urs

a da

y, 7

day

s a

wee

k.

Our

frie

ndly

cus

tom

er s

ervi

ce te

am is

her

e to

ass

ist

you

with

pla

cing

you

r or

der.

You

can

reac

h us

at

800

-366

-221

8 be

twee

n 9:

00am

–4:3

0pm

ES

T,

Mon

day–

Frid

ay.

CU

RR

ENT

RES

IDEN

T (O

CC

UPA

NT)

OR

PR

ES

OR

TED

STA

ND

AR

DU

.S. P

OS

TAG

EPA

IDP

RIM

A B

EA

D12

333

EN

TER

PR

ISE

BLV

D.

LAR

GO

, FL

337

73

pattern book vol. 1 from primabead.com

Documents

white oval

purple hexagon

wire cutters

excess wire

gauge wire

strand beading wire

length of silver cord

silver satin cord