SAFETY PRECAUTIONS• Read instructions and identify all component parts before using the crimper and saw.• Familiarize yourself with the safety and operating procedures for the crimper and saw before use.• Use all safety precautions listed.• Consult the Continental CrimpIQ™ Tablet for Crimp Specifications for correct crimper settings and crimp measurements.• Always wear eye protection.

i

PC150 SHOP IN A BOXQuick Start Guide

Updated: 09/22/2020 www.continental-industry.com

Continental QR CodeH: 2.25 inW: 1.35 in

Use your smartphone to scan the Continental QR Code to get full access to the operators manuals and training videos.

Initial Setup

2

Setting Up Accessories

Step #1. Position your new PC150 SHOP IN A BOX near to the appropriate electrical outlet. Check the voltage tag attached to the power strip supply cord #1, PC150-2 crimper’s power cord #2 and HS-501 hose saw’s power cord #4.

Note: Check electrical circuit to be certain that it matches the crimper and saw requirements shown on the voltage tag attached to the power cord.

Locate the power strip supply cord #1 and plug it directly into a 110V outlet. Do not use an extension cord.Plug in the CrimpIQ™ Controller’s power cord (3), and the light’s power cord (5) into the power strip supply cord as shown in the picture.

Caution: Do not run the power strip, crimper, and saw on an extension cord, as low voltage can damage themotors and/or electrical components.

Step #2. Familiarize yourself with the safety and operating procedures for the crimper and saw before use.Use all safety precautions listed on the quick start guide.

Step #3. Locate the tooling box, it contains the accessories needed to finish setting up your Shop-in-a-box.

a. Connect air nozzle and Continental air hose to shop air supply.

b. Install hose saw handle and alignment pins as shown. c. Note optional vacuum adapter is included if you want to connect see instructions in saw operating procedure.

Step # 2 Step # 3a

Step # 1

Step # 3b Step # 3c

23

4

5

1

3

Setting Up Accessories

d. Place the inserting block assembly on the table as desired. Please note that this can go on the edge of table if needed. e. Removing tooling and lubrication and place on the rubber mat on table. Organize in a way you feel most efficient.

f. Locate the tablet box, it contains the CrimpIQ™ tablet. This has the most recent Continental crimp specs readily available. This can be mounted to either signpost as shown.

Step # 3d Step # 3e Step # 3f

36" Hose Reel Rack Instructions

Step #4. Locate the hose reel box.Step #5. Locate the instructions on how to assemble your stand alone hose reel rack assembly.Note: Hardware included.Step #6. Hose reel rack is shown fully assembled.

Step #4 Step #5 Step #6

1

1

2

2

3

3

4

4

A A

B B

C C

D D

SIZE PART NO REV

SCALE SHEET OF

DRAWN

CHECKED

APPROVED

QA

MFGTITLE

104935-361 1

AC

CUSTOM MACHINING SERVICESVALPARAISO, INDIANA

JRI 4/24/2018

M:\Dwg\Hose Reel\AI-104935-36.iam

.1 : 1

36'' HOSE REEL RACK ASSEMBLY

HOSE REEL RACK 36'' WIDE BOM LISTQTYDESCRIPTIONPART NUMBERITEM

1Left Upright Assembly104932-L11Right Upright Assembly104932-R2236'' Spacer Bar104934-363136.5'' Spacer Bar104934-36.54

485/16 Flat Washer91090A1105245/16-18 Nylon Locking Hex Nut95615A1606245/16-18 x 1'' HHCS92865A58373Hose Reel Bar105058-45.586Plastic End Cap9283K1692Logo Sticker 101Serial Tag Sticker 11

2 PLC. DEC. 0.010

ANGULAR 1/2FRACTIONAL 1/64

TOLERANCE UNLESS OTHERWISE NOTED:

3 PLC. DEC. 0.0054 PLC. DEC. 0.0005

ALL DIMENSIONS ARE IN INCHES [METRIC].BREAK ALL SHARP EDGES .015"-.030".FINISH ALL OVER 125 MICRO MAX.

REV DESCRIPTION

75

56

4

2

1

3

3

AADDED A GUSSET TO BASE FOR STRENGTH 3/15/18 JRI

10

11

8

9

4

Continental QR CodeH: 2.25 inW: 1.35 in

Scanning Continental QR Code

PC150 SHOP IN A BOX Identification Components

Step #7. Use your smartphone to scan the Continental QR Code to get full access to the operational manuals and training videos.Note: If you don’t have a QR code reader app installed in your smartphone, download it from your smartphone app store.

Step #8. Read the crimper quick start guide before operation. Scanning the QR code will allow access to the full operational manual.

Step #9. Read the hose saw quick start guide before operation. Scanning the QR code will allow access to the full operational manual.

Step #7 Step #9Step #8

3

11

1312

15

14

109

876

54

1

2

1. 36" Hose Reel Rack(Hose spools not included)

2. 6' LED Light Kit

3. 6' Continental Sign

4. Hose Helper

5. 10' Continental Air Hose with Nozzle

6. HS-501 Hose Saw(Handle, Vacuum Port, and Alignment Pins)

7. Insertion Block Assembly(B2 and SG blocks, (5) PaintMarkers)

8. CrimpIQ™ Tablet and Mounting Arm

9. Tape Measure

10. PC150-2 Tooling Box and Tooling Mat

11. PC150-2 Crimper(Dies, Shelf, and Tooling Box)

12. 5' 110V Power Strip

13. 4 Drawer Cabinet with Small and Large Bins

14. PC150 Die Shelf

15. Adjustable Feet