ul ti mate ™ range of underwater lights™ ti mate ™ range of underwater lights™ ... ul ti...

UL Ti MATE ™ Range of underwater lights™

(click on document required)

Technical Brochure Info

UL Ti MATE 75 SA (S.S) UL Ti MATE 75 SA (S.S) UL Ti MATE 75 SA (ALU) UL Ti MATE 75 SA (ALU)

UL Ti MATE 75 Fixed (S.S) UL Ti MATE 75 Fixed (S.S) UL Ti MATE 75 Fixed (ALU) UL Ti MATE 75 Fixed (ALU)

UL Ti MATE 130 SA UL Ti MATE 130 SA UL Ti MATE 130 Fixed UL Ti MATE 130 Fixed

UL Ti MATE 80 Xenon UL Ti MATE 80 Xenon

UL Ti MATE 80 20w LED UL Ti MATE 80 20w LED

Qt 80 LED Qt 80 LED

For sales telephone numbers visit www.underwaterlights.com

un

de

rw

at

er

ligh

ts

lim

ite

dTM

UL Ti MATE RANGE - MODEL- UL Ti MATE 130 SA

DESCRIPTIONThis is the most flexible and powerful“through-hull” submersible marine light forthe large sports fish yachts and is suitable forGRP-fibreglass and wooden hulls.The design and development of the UL Ti MATE 130 SA gave the marine markettheir wish with the internal adjustment (SA)which allows the beam angle to be varied froma narrow to wide beam and to universallymove the beam direction by 20 degrees fromwithin the projector housing.The UL Ti MATE 130 SA has a larger aperturewhich increases the light output by 25%.We advise that the light be installed 250mmbelow the minimum waterline.The boat must be hauled out for installation,although maintenance of the light is carriedout from inside the hull.The light is IPX8 to 10 bar.

TECHNICAL SPECIFICATIONLamp Type - MSD Metal Halide 150w or 250w

Material - Aluminium Bronze and 5083 ALU

Glass Lens - Borosilicate glass

Lamp Life - 3000 Hours - Colour Temp - 7000 K

NOTEInstallation Instruction:The hole cut-out should be 100 mm.For Lamp Maintenance allow 170mm behind the projector lid.Hull thickness range 12 to 120 mm.Electrical Information:150w - Recommended maximum distance between ballast and projector 10m.250w - Recommended maximum distance between ballast and projector 25m.Cable - 150w-250w High temp. silicone 3 core (Part No S00111, 0.75). For additional information please visit our web site.

underwater lights limited™

Manufacturers of the Original underwater lights ™Brand Marine Lighting Products since 1991

UL Ti MATE 130 SA-W1 (250 WATT)ORDER NUMBER-S00475-SA-V1W1

UL Ti MATE 130 SA-W2 (150 WATT)ORDER NUMBER-S00475-SA-V2/V3W2

Max hull thickness 120mm

130m

m

Hol

e cu

t-ou

t 100

mm

222mm

Max hull thickness 120mm

130m

m

Hol

e cu

t-ou

t 100

mm

222mm

UL Ti MATE 130 SA12,000 or 19,000 lumen

Voltage/Amps - 150 watt 120(V3)/230(V2)volt - 1.4 /0.7.A

Voltage/Amps - 250 watt 198/264vac- 1.2A

Light Level - 150w 12,000 Lumens - 250w 19,000 lms

Qualified/Approved personnel must be used to carry out installationCut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screwthe securing ring (18) up “hand tight”. Adjust the screws (19) so the compensating ring is flush to the hull and check the

sealant has flowed completely around the flange. Do “NOT” over tighten the screws as this will squeeze the sealant from the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbsNote for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it, thus protecting the internal core of the hull.Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mmAfter completing the installation procedure it is highly recmmended to coat the exposed body with antifouling.EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.

ORDERING NUMBERS250 WATT LIGHTS - 120V. S00475-SA-V3W1. 230V. S00475-SA-V2W1.150 WATT LIGHTS - 120V. S00475-SA-V3W2. 230V. S00475-SA-V2W2

UL Ti MATE 130 SA INSTALLATION (The UL Ti MATE 130 SA should be no less than 250mm/10” below the water line)

LENS FITTING INSTRUCTIONSCheck the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with an Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs) in the sequence shown, check the ring again and re-torque the screws again to the same setting

ELECTRONIC BALLAST COMPLETE WITH IP65 ENCLOSURE

PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COMFOR TECHNICAL INFORMATION PLEASE EMAIL [email protected]

SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM

UL Ti MATE 130 SA -1-7-2010

Recommended Spares Part NoLamp ( 250w = W1 ) 91209Lamp ( 150w = W2 ) 91210Glass with gaskets S00281-A

Ballast S00801

TM

OPERATIONAL CONDITIONS AND CONSIDERATIONSThe UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp replacements on 150w and 150mm behind the.ignitor on 250wELECTRICAL INFORMATIONCABLE SPECIFICATION TO PROJECTOR150 Watt High temp silicone three core part number. S00111- 250 Watt Two core 1mm square. maximum diameter 6mm150 WATT Max distance between ballast and projector with -10 meters.250 WATT Max distance 25 meters.Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.ABallast power 250 watt ballast 120/230 volt, running current 2.4/1.2.ABallast will not ignite a hot lamp. The ballast has three attempts to ignite the lamp then will wait for four minutes before repeating the cycle.Do not attempt to remove the glass lens while afloat

UL Ti MATE 130 SA‘submersible through hull light’

150 watt 250 watt

Part Description 130-SA Part No1: Projector lid securing plate 00283-B2: M6 Nut 933813: 'O' Ring 001084: Gasket NAF 00285-A5: Connecting ring 00274-C6: Lamp holder screw 002907: Lamp holder (250W) 911957: Lamp holder (150W) 911918: Reflector collar bush 00288-A9: M4 Lock nut 9337410: Lamp (250W) 9120910: Lamp (150W) 9121011: Reflector adjustment rod 00284-2-D12: Reflector complete S9179113: Glass retaining ring 00476-B13A: Cap head screws 9332514: Glass gaskets NAF 00286-A16: Body S00475-A17: Compensating ring 0027718: Securing ring 0027519: Cap head screws 9361020: Ignitor (250W) S9532521: Projector cover (250W) 00102-H22: Gland 0010723: Projector cover (150W) 00102-E24: Ballast 250 watt S00800-V1W224: Ballast 150 watt 230v S00800-V2W224: Ballast 150 watt 120v S00800V3W2

EARTH TAB AND SCREW

��

��

��

�

��

��

�

��

��

��

UL Ti MATE RANGE - MODEL - UL Ti MATE 130 -FIXED

DESCRIPTIONThis is a 150 watt MSD discharge lamp“through-hull” submersible marine lightwith a flush lens for the large sports fishboats, motor and sailing yachts and issuitable for GRP-fibreglass and woodenhulls.The UL Ti MATE 130 FIXED has a largeraperture than our original screwed fittingwhich has increased the light output by25%.We advise that the light be installed 250mmbelow the minimum waterline.The boat must be hauled out forinstallation, although maintenance of thelight is carried out from inside the hull.The light is IPX8 to 10 bar.



TECHNICAL SPECIFICATIONLamp Type - MSD Metal Halide 150w


Flush Glass Lens - Borosilicate glass


NOTEInstallation Instruction:The hole cut-out should be 100-101 mm.For Lamp Maintenance allow 150mm behind the projector lid.Hull thickness range 12 to 75 mm.Electrical Information:150w - Recommended maximum distance between ballast and projector 10m.Cable - 150w-High temperature silicone 3 core (Part No S00111).

For additional information please visit our web site.

Voltage - 120(V3) or 230(V2) vac-

Amps - 120 v = 1.4 amps 230 volt = 0.7 amps

Light Level - 150w 12,000 Lumens

=+

��=@!�>�� !!�Y�

��&,11

�0�1

1

��

��

11��

�*�11

� ��!"��#�$��"��%��!��&$!��!��'(��)�"�

UL Ti MATE 130 Aluminium Bronze Fixed Screwed Underwater Lights

ORDERING NUMBER FOR 230 VOLT 150WATT LIGHTS S00475-V2(H)W2ORDERING NUMBER FOR 120 VOLT 150WATT LIGHTS S00475-V3(H)W2

LENS FITTING INSTRUCTIONSCheck the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs) in the sequence shown, check the ring again and re-torque the screws again to the same setting

ELECTRONIC BALLAST COMPLETE WITH IP65 ENCLOSURE



UL Ti MATE 130-FIXED 1-7-2010

Qualified/Approved personnel must be used to carry out installationCut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screwthe securing ring (18) up “hand tight”. Adjust the screws (19) so the compensating ring is flush to the hull and check the

sealant has flowed completely around the flange. Do “NOT” over tighten the screws as this will squeeze the sealant from the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbsNote for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it, thus protecting the internal core of the hull.Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mmAfter completing the installation procedure it is highly recmmended to coat the exposed body with antifouling.EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.

UL Ti MATE 130 INSTALLATION (The UL Ti MATE 130 should be no less than 250mm/10” below the water line)

OPERATIONAL CONDITIONS AND CONSIDERATIONSThe UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp replacements on 150w and 150mm behind the.ignitor on 250wELECTRICAL INFORMATIONCABLE SPECIFICATION TO PROJECTOR150 Watt High temp silicone three core part number. S00111150 WATT Max distance between ballast and projector with -10 meters.Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.ABallast will not ignite a hot lamp. The ballast has three attempts to ignite the lamp then will wait for four minutes before repeating the cycle.Do not attempt to remove the glass lens while afloat

Part Description Part No1: Cable S001112: Projector lid complete S00102-C3: "O" Ring 001084: Connecting Ring 00274-B5: Body S00475-A6: Screws (M6X 25 ALU.) 936107: Gasket - NAF 00286-A8: Glass 00281-F9: Glass retaining ring 00476-C10: Comp. ring 00277-A11: Securing ring 00275-A13: Electronic ballast-230 volt 95322-V2HW213: Electronic ballast-120 volt 95322-V3HW212: Reflector Tube with Reflector S0027314: Lamp (MSD-150W/70) 9121015: Gasket - NAF 000C07-A16: Cable gland 9201017: Screws (M6X 16 S.S.) 93333Recommended Spares Part NoLamp (MSD-150W/70) 91210Glass with gaskets S00279-AElectronic ballast 95322

EARTH TAB AND SCREW

��

��

��

�

��

��

�

��

��

��

�

UL Ti MATE RANGE - MODEL NUMBER - S02652

DESCRIPTIONThis is our most popular “through-hull”submersible marine light IPX8 rated to 10 bar forcoastal power boats and some ten thousand havebeen installed world wide. The light is suitable for installation into GRP-fibreglass and wooden hulls and must be installedbelow the minimum waterline.The boat must be hauled out for installation,although maintenance is carried out from insidethe hull.The light has a sealed integral igniter which makesit safer, and allows the ballast to be located awayfrom the bilge area.The latest UL Ti MATE 80 can also be fitted with awide beam lens. Also available in an extended version.

TECHNICAL SPECIFICATION

NOTE-Installation Instruction:The hole cut-out should be 61 mm.Hull thickness range 12-65 mm and 80-110mm.Recommended distance between lights 1 to 2 metresElectrical Information:Recommend only 2 lights for each power supply cable. See wiring diagram on opposite page.

For additional information please visit our web site.

Lamp Type - Xenon bulb

Light Output - 4,800 Lumens


Classification - Lloyds Approved


Voltage / Amp 12VDC/6.4A - 24VDC/2.5.A


40mm

180mm

80mm



��!��"�"�#�!!�$%&�"

��!'��(��)��*��' !+9�+';�(+�;)�<;9(=+;)

��!'��>��

��*��' !+9�+'��'

��*�� *��

' ?�@!�'�;�(+�;)��<� ?�@!�'�;9(=+;)

��

��

�

��

��

��

��

��

�

��

��

�

��

��

��

UL Ti MATE RANGE - MODEL NUMBER - S02652-V5/V6

WIRING DIAGRAM 24V/V5

WIRING DIAGRAM 12V/V6



��

��

��

��

��

�� !"#$%��&'()��*+,�� -��-��- ��

��.��,�

��.��/,0�*

��.��/,0�*

9

��.��/,0�,

��

��

��*��

��

��.��/,0�,

��

��*+,�� !"#$%��*'()��+�� -��-��- ��

��.��,�

UL Ti MATE 80 ‘submersible through hull light’

‘Xenon’ with 55 watt BallastLAMP TYPE - XENON DISCHARGE 55 WATT

ORDERING NO FOR 12 VOLT - S02652-V6W5 & 24 VOLT - S02652-V5W5

UL Ti MATE 80 Installation (Maximum hull thickness 60mm) and Operation instructions.Qualified/Approved personnel must be used to carry out installationBefore cutting a hole in the hull, check the hull wall thickness is not greater than 60mm. The location of the holes must be

below the waterline. After cutting and finishing the hole surface, check the 60mm diameter. UL Ti MATE 80 ‘body’ (9)can be inserted. Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface

through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the ‘body’ (9) flange. Slide the body into the hole and from inside the hull putthe ‘compensating ring’ (10) on and screw the ‘case securing ring’ (11) up hand tight. Gently tighten the adjustment screws(6) so the compensating ring is flush to the hull and the sealant has flowed completely around the flange and hullDo NOT overtighten the bolts as this will squeeze the sealant from the surfaces. Allow the sealant to solidify and remove

surplus. Finally tighten the bolts to 4Nm. / 3ft. lbs.Note: Maximum ambiant operating temperature is 55C/131F of the ballastThe ballast must be installed a minimun of 24 inches (600 mm) above the bilge. Fit the ‘lamp’ (5) and assemble the

remaining parts to the ‘through-hull’ submersible marine light. Lightly grease the ‘O’ rings. When fitting a new lamp makesure the lamp is switched off and bring the ignitor, lamp and reflector tube away and above the bilge to the highest point before changing the lamp. Cautionary Label-“Caution: do not operate lights unless totally submerged” must be located by the main switch.

EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that itbites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.After completing the installation procedure it is highly recommended to coat the face of the ‘through-hull’submersiblemarine light with antifouling and bond them to the anodes or a cathodic protection system. Power supplyThe 12 volt D.C ballast can operate between 11-13.5 volts. Start up current is 8 amps and 6.4 amps continuous.The 24 volt D.C ballast can operate between 21-26 volts. Start up current is 4.5 amps and 2.5 amps continuous. Note a maximum of two lamps can be connected to one cable supply. The correct size cable must be used and the

maximum volt drop (1.5 volts) on the cable length should be calculated using the maximum start up current.

Part Description Part No1: Ballast 12 vdc 55 watt 953041: Ballast 24 vdc 55 watt 953052. Igniter 953063.'O' Ring (40mm) 020074.'O' Ring (50mm) 020085: Xenon lamp 55 watt 910126: Adjustment screws 933357: Gasket 020098: Lens 020109: UL Ti MATE 80 Body S0265210: Compensating ring 0260211: Securing ring 02603-B12: Reflector with tube S0260513: Lamp holder securing ring 02608-A



Ul Ti Mate 80 S02652 1-9-2010

TM

BALLAST PLUG POSITION

QT LED 80 CONNECTION

POWER SUPPL

EARTH EARTH

EARTH TAB AND SCREW

UL Ti MATE 80 Extended‘submersible through hull light’

‘Xenon’ with 55 watt BallastLAMP TYPE - XENON DISCHARGE 55 WATT

ORDERING NO FOR 12 VOLT - S02652-XT-V6W5 & 24 VOLT - S02652-XT-V5W5

UL Ti MATE 80 Extended Installation (Maximum hull thickness 120mm) and Operation instructions.Qualified/Approved personnel must be used to carry out installationBefore cutting a hole in the hull, check the hull wall thickness is not greater than 120mm. The location of the holes mustbe below the waterline. After cutting and finishing the hole surface, check the 60mm diameter. UL Ti MATE 80 ‘body’(9) can be inserted. Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface

through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the ‘body’ (9) flange. Slide the body into the hole and from inside the hullput the ‘compensating ring’ (10) on and screw the ‘case securing ring’ (11) up hand tight. Gently tighten the adjustmentscrews (6) so the compensating ring is flush to the hull and the sealant has flowed completely around the flange and hullDo NOT overtighten the bolts as this will squeeze the sealant from the surfaces. Allow the sealant to solidify and removesurplus. Finally tighten the bolts to 4Nm. / 3ft. lbs.Note: Maximum ambiant operating temperature is 55C/131F of the ballastThe ballast must be installed a minimun of 24 inches (600 mm) above the bilge. Fit the ‘lamp’ (5) and assemble the

remaining parts to the ‘through-hull’ submersible marine light. Lightly grease the ‘O’ rings. When fitting a new lampmake sure the lamp is switched off and bring the ignitor, lamp and reflector tube away and above the bilge to the highest point before changing the lamp. Cautionary Label-“Caution: do not operate lights unless totally submerged” must be located by the main switch.After completing the installation procedure it is highly recommended to coat the face of the ‘through-hull’submersiblemarine light with antifouling and bond them to the anodes or a cathodic protection system. Power supply12 VOLT BALLAST- 12 volts DC- 6.4 amps. : 24 VOLT BALLAST- 24 volts DC- 2.5ampsNote a maximum of two lamps can be connected to one cable supply. The correct size cable must be used and the

maximum volt drop (1.5 volts) on the cable length should be calculated using the maximum start up current.LAMP CHANGE - To change the lamp undo the ‘grub screw’ (3) and remove the ‘reflector tube’ (12). Insert the lampinto the ‘lamp holder’ (2) and replace the ‘reflector tube’ (2) and tighten the ‘grub screw’ (3).

Part Description Part No1: Ballast 12 vdc 55 watt 953041: Ballast 24 vdc 55 watt 953052. Lamp Holder 953063. Grub screw 933084.'O' Ring (50mm) 020085: Xenon lamp 55 watt 910126: Adjustment screws 933357: Gasket 020098: Lens 020109: UL Ti MATE 80 Body S02652-XT10: Compensating ring 0260211: Securing ring 02603-B12: Reflector with tube S02605-XT13: Lamp holder securing ring 02608-A



UL Ti MATE 80 Extended - S02652-XT - 1-9-2010

TM

3S02605-XT

S02605-XT

BALLAST PLUGPOSITION


un

de

rw

at

er

ligh

ts

lim

ite

dTM

UL Ti MATE RANGE - MODEL NUMBER - S02860 -

DESCRIPTIONThe UL Ti MATE 80, 20W LED is a“through- hull” submersible marine lightrated IP68 to 10 bar.The light is suitable for small boats andcan be installed into GRP-fiberglass andwooden hulls. It must be installed below the minimumwaterline.The boat must be hauled out for installation, although maintenance of theLED is carried out from inside the hull. The LEDs are available in blue, red,green or white.The LED driver is integral with the light.


NOTE-Installation InstructionThe hole cut-out should be 61 mm.Hull thickness range 12-65mmRecommended distance between lights 1 to 2meters.Electrical InformationSee diagram opposite. The 12/24vdc driver is integral,just connect the red wire to the +VE and black wire tothe -VE 12/24vdc power supply. Maximum number of lights on one supply cable TWO For additional information please visit our web site.



Lamp Type - 7 x single 110 lumen LED-

Light Output - 1,400 Lumens


Classification - Lloyds Approved


Voltage/Amps - 12vdc/1.6 A - 24vdc/0.8 A

Lamp Life - 30,000 Hours - Colour Temp - 7200K

POWER SUPPLY 12 VOLTS DRIVER 24 VOLTS DRIVER

+ VE RED- VE BLACK

MAXIMUM 2 LAMPS ON THE SAME SUPPLY CABLE.THE 12-24 VDC DRIVER CAN OPERATE BETWEEN MIN 10 VDC 10.5 (-5%) 28.5 (+ 5%) MAX 30 VDC

UL Ti MATE 80 LED1,400 lumen

60m

m

82m

m

122mm

1

23

4

5 6 7 9

8

Max 2 lamps on thesame supply cable

UL Ti MATE 80 Alu-Bronze‘submersible through hull light’

20 Watt LED

ORDERING NUMBERS : -S02860


SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COMUL Ti MATE 80 AB2-AL-15-09-10

UL Ti MATE 80 Installation (Maximum hull thickness of 65mm) and Operation.Qualified/Approved personnel must be used to carry out installation.Before cutting a hole in the hull, check the hull wall thickness is not greater than 65mm and that the

location of the holes are below the waterline. After cutting and finishing the hole surface, check the ‘body’(5) can beinserted into the 60mm diameter hole. You are now ready for installation.Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface

through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the ‘body’ (5) flange. Slide the body into the hole and from inside thehull put the ‘compensating ring’ (6) on and screw the ‘securing ring’ (7) up hand tight. Gently tighten the adjustment adjustment screws (2) so the compensating ring is flush to the hull and the sealant has flowed completely around theflange and hull. Do NOT overtighten the screws as this will squeeze the sealant from the surfaces. Allow the sealantto solidify and remove surplus. Finally tighten the bolts to 4Nm. / 3ft. lbs. Fit the lamp and assemble the remainingparts to the UL Ti MATE 80. Lightly grease the ‘O’ ring and gasket.Cautionary Label-“Caution: do not operate lights unless totally submerged” must be located by the mainswitch.After completing the installation procedure it is highly recommended to coat the face of the ‘through-hull’submersible marine light with antifouling and bond them to the anodes or a cathodic protection system.

EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring sothat it bites into the screwed barrel. Check there is continuity to the front face. This prevents galvaniccorrosion.

TM

Part Description Part No1. 'O' Ring (50mm dia) 020082.Adjusment screws 933063. Gasket 020094. Glass lens 020105. Ultimate 80 Body S026506. Compensating Ring 02602-A7. Securing Ring 026038. LED tube S02605-LED9: Lamp holder securing ring 02608-B

Power Supply and CONNECTION20 Watt 12 Volt LED unit requires 1.60 Amps20 Watt 24 Volt LED unit requires 0.80 AmpsEnsure the the polarity of the positive and the negative is correct so that the integral driver is not damaged

60m

m

82m

m

122mm

1

23

4

5 6 7 9

8

EARTH TAB AND SCREW

UL Ti MATE 80 CONNECTION

POWER SUPPLY

EARTH EARTH

QT 80cute in size big on light

PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW.QTLED/REG.COM

SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,QTLED.COM

QT LED 80 17-04-2012

(lux)

5,500 LUMEN

3605301650

1m 2m 3m5,500 LUMEN

34001020530

(lux)

Qt LED 80 & NARROW BEAM (65deg) LUX CHART

Qt LED 80 & WIDE BEAM (80deg) LUX CHART

80 DEG

65 DEG

FLAT (130deg) LUX CHART

3M - 2302M - 3301M - 1000


LED lamp life - 20,000 hours @ 60° C

Bezel Material - Aluminium Bronze & 5083 ALU.

Glass lens - Borosilicate wide beam glass as standard

VDC. LED Driver - Min 22- Max 28vdc maximum current 3.3amps.

Lamp types - Single LED chip- 5,500 lm- 7,200K (Cool White)Also available in blue, green, and red

60M

M80MM

84MM

2-COMPENSATING RING

6-M6 CAP HEAD BOLT

5-COVER

1-BODY FORWIDE LENS

3-SECURING RING

4-LED HEAT SINK

7-'O' RING

QT LED 80 CONNECTION

POWER SUPPL

EARTH EARTH

Qt LED 80 Installation (Maximum hull thickness 60mm) and Operation instructions.The QT 80, is a “through- hull” submersible marine light and is delivered ready for installation. Maintenanceof the LED is carried out from inside the hull. The light is suitable for installation into GRP-fiberglass and wooden hulls. LED output 5,500 lumens -Colour temperature of 7,200K. Other colours are available also RGB.Qualified/Approved personnel must be used to carry out installationBefore cutting a 60mm hole in the hull, check the hull wall thickness is not greater than 60mm. The location of

the holes must be below the waterline. After finishing the hole surface, check the Body (1) can be inserted. Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface through it. Thus protecting the internal core of the hull. The wall thickness of the hole should not to less than 5mm-0.25inch. Apply 3M-4200FC sealant to the ‘Body’ (1) flange. Slide the body into the hole and from insidethe hull put the ‘compensating ring’ (2) on and screw the securing ring’ (3) up hand tight. Gently tighten the adjustment screws (6) so the compensating ring is flush to the hull and the sealant has flowedcompletely around the flange and hullDo NOT overtighten the bolts as this will squeeze the sealant from the surfaces. Allow the sealant to solidifyand remove surplus. Finally tighten the bolts to 4Nm. / 3ft. lbs.When all parts are assembled and the sealant has cured tighten the cover (5) to secure the heatsink (4) into thebody. If this is not done it will cause overheating of the LED and the LED could fail. EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that itbites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.Cautionary Label-“Caution: do not operate lights unless totally submerged” must be located by the main switch.After completing the installation procedure it is highly recommended to coat the BODY (1) face with antifouling and bond them to the anodes or a cathodic protection system.

Part Description1: Body2: Compensating ring3: Securing ring 4: LED Heat sink5: Screwed cover6: Adjustment screws7: Nitrile 'O' ring

Drivers for Qt 80 Part NoSupply 230 vac Output 24vdc - 3.3amps QTD-8599981ESupply 24-48dc - Output 24vdc - 3.3amps QTD-5599981E

4-LED HEAT SINK

5-COVER

7-'O' RING

2-COMPENSATING RING

3-SECURING RING

1-BODY FORWIDE LENS

24 dc DRIVERQTD-5599981E

EARTH TAB AND SCREW

QT 80cute in size big on light

PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW.QTLED/REG.COM

SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,QTLED.COM

QT LED 80 17-04-2012

(lux)

5,500 LUMEN

3605301650

1m 2m 3m5,500 LUMEN

34001020530

(lux)

Qt LED 80 & NARROW BEAM (65deg) LUX CHART

Qt LED 80 & WIDE BEAM (80deg) LUX CHART

80 DEG

65 DEG

FLAT (130deg) LUX CHART

3M - 2302M - 3301M - 1000

LUX CHART

DESCRIPTIONThe QT 80, is a “through- hull” submersible marinelight tested at front of glass to IP68 at 10 bar. Thelight is suitable for installation into GRP-fiberglassand wooden hulls. There are three types of lenses for different beamwidths - the standard is wide 95 deg, flat 130deg andnarrow 70deg. The standard LED produces 5,500 lumens -Colourtemperature of 7,200K. Other colours are available,also RGB.The light must be installed below the minimumwaterline. The boat must be out of the water forinstallation. Maintenance of the LED is carried outfrom inside the hull. The LED driver is fitted into an enclosure and ismounted remotely.Note this light can be driven at low outputs to suitboat battery power.


LED lamp life - 20,000 hours @ 60° C

Bezel Material - Aluminium Bronze & 5083 ALU.

Glass lens - Borosilicate wide beam glass as standard

VDC. LED Driver - Min 22- Max 28vdc maximum current 3.3 amps Order No. QTD-5599981E

Mains Power LED Driver -100-265vac. Output 24vdc, maximum current 3.3amps Order No. QTD-8599981E

Lamp types - Single LED chip- 5,500 lm- 7,200K (Cool White)

NOTE-Installation InstructionThe hole cut-out should be 61 mm.Hull thickness range 12-65mmRecommended distance between lights 1 to 2meters.The light is supplied with 3 meters of 6mmdiameter, 2 core marine grade cable. For VDC power supply the maximum number oflights on one supply cable of AWG 10 is TWO (See wiring diagram opposite)For additional information please visit our web site.

Earthing instructionAfter the light has been installed tighten the earthscrew on the securing ring sothat it bites into thescrewed barrel. Check there is continuity from theearth tab to the front face of the light. This is veryimportant to stop galvanic corrosion of the front face

Standard QT LED 80 - with wide beam lensLED Output 5,500 lumen, 7,200K

Order Number QT LED-80-24vdc

Qt LED 80 LED

24 VDC POWER SUPPLY

AWG 10 - CABLE

60M

M80MM

84MM

2-COMPENSATING RING

6-M6 CAP HEAD BOLT

5-COVER

1-BODY FORWIDE LENS

3-SECURING RING

4-LED HEAT SINK

7-'O' RING


un

de

rw

at

er

ligh

ts

lim

ite

dTMDESCRIPTION

The UL Ti MATE 75 Fixed is a “through-hull”submersible marine light for welding into alu-minium and steel hulls. Maintenance of the lightis carried out from inside the hull.It does not include the SA 'Super Adjustable' unitand has been introduced to compete fairly withother fixed lights on the market. The lens aper-ture is exactly the same as the SA to give thesame maximum light output.This new light is also shorter in length to the SAunit so that it is easier to fit into those smallareas. We advise that the light be installed minimum250mm below the waterline when the yacht isloaded with 50% fuel and 50% water, and that thelight be angled 15 degrees downwards. Toachieve this there are 3 models- Flush, 30 degree and 50 degree.The stainless steel model comes as standard withIce Class Lloyds Approval and has been pres-surised to 80 bar. The aluminium model is IPX8to 10 bar. The range is also GL Approved.

Lamp Type - MSD Metal Halide 150w

Light Level - 150w 12,000 Lumens

Material - Steel and 5083 ALU


Ballast - 150 watt electronic in IP 65 Enclosure

Voltage/Amps - 150 watt 120(V3)/230(V2) - 1.4/0.7.A


NOTEInstallation Instruction:The hole cut-out should be cut to suit the insertangle. Maximum hull plate thickness should be12mm for the flush and 20mm for the 30 & 50degree.For Lamp Maintenance allow 60mm behind the cable gland.Electrical Information:150w - Recommended maximum distance between ballast and projector 10m.Cable - High temp. silicone 3 core (Part No S00111). For additional information please visit our web site.



168mm27mm

120m

m

115m

m

168mm75mm

120m

m

115m

m

105mm

140m

m

115m

m

40mm

168mm

UL Ti MATE RANGE - MODEL - UL Ti MATE 75 FIXED 150W

TECHNICAL SPECIFICATIONOrder Number Flush-STEEL S00300-75-ICE-V2/V3W2

Order Number Flush-ALU S00600-75-V2/V3W2

Order Number 30 deg. STEEL S00330-75-ICE-V2/V3W2Order Number 30 deg. ALU S00630-75-V2/V3W2

Order Number 50 deg. STEEL S00350-75-ICE-V2/V3W2Order Number 50 deg. ALU S00650-75-V2/V3W2

UL Ti MATE 75 30 degree

UL Ti MATE 75 316L STAINLESS STEEL AND 5083 ALUMINIUM

Part Description Part No1; Projector Cable S001112; Projector lid complete S00C102-B3; "O" Ring 001084; Projector case 00101-B5; Lamp (150w MSD) 912106; Reflector 91791-C7; AB2 Connecting ring 00503-75-A8; Gaskets 00285-A8A; Gaskets 000C07-B9; S.S.316L Body 003XX-759; Alu 5083 Body 006XX-7510; S.S. M6 socket screws 9333410; Ti. M6 socket screws 93460-SC11; S.S. Glass retaining ring 00304-ICE 75B11; Alu Glass retaining ring 00604-75B12; Gaskets 00286-A13; Glass 0028114; Electronic ballast 120V 95322-V3-H14; Electronic ballast 230V 95322-V2-H14A; Enclosure 00806-A

Recommended Spares Part NoLamp 91210Glass with gaskets S00281Electronic ballast S00801

LENS FITTING INSTRUCTIONSCheck the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm “Allen key” making sure the glass retaining ring is square. Torque settings for all retaining screws - 10 Nm (7.5 ft/lbs). Torque the screws in the sequence shown. Check the ring again and re-torque the screws again to the same torque setting.

ELECTRICAL INFORMATION Cable specification from electronic ballast to projector (Pt.No. S00111)Shielded 3 core, Temperature -60C to +180C, Voltage 2000 volts.Maximum distance between ballast and projector with the shield earthed 10 meters.Ballast power 120/230 volt 150 watt ballast - running current 1.4/0.7ABallast will not ignite a hot lamp. The ballast has a cycle of three attempts to ignite the lamp then will wait for four minutes before repeating the cycle. Install ballast in a dry space. Maximum ambient temperature 40C

The UL Ti MATE 75 is serviced from inside the hull. Allow access for maintenance and space for ventilation.Do not use the LIGHT in dry-dock or out of the waterAllow a minimum of 70mm behind the projector lid (item 2) for lamp replacements.UL Ti MATE 75 to be fitted 250mm below the yachts water line when loaded with 50% fuel and 50% freshwater onboard.

Do not attempt to remove the glass lens while afloat.The projector must be correctly assembled with lid secured to the UL Ti MATE 75 whilst afloat.

OPERATIONAL CONDITIONS AND CONSIDERATIONS

ELECTRONIC BALLAST



UL Ti MATE 75 ICE S.S + UL Ti MATE 75 ALU-1-9-2010

ORDERING NUMBERS FLUSH - S00300-75-ICE. 30 DEG - S00330-75-ICE. 50 DEG -S00350-75-ICE

FLUSH - S00600-75. 30 DEG - S00630-75. 50 DEG -S00650-75WITH 120 (V3) / 230 (V2) VOLT BALLAST AND 150W (W2) WATT LAMP.

30 DEGREE

FLUSH

00304-ICE-75B

50 DEGREE

00604-75B

140 mm


un

de

rw

at

er

ligh

ts

lim

ite

dTMDESCRIPTION

This is a “through-hull” submersible marinelight for welding into aluminium and steelhulls. Maintenance of the light is carried outfrom inside the hull.Our patent pending internal SA ( SuperAdjustable) unit allows the beam angle to bevaried from a narrow to wide beam, and touniversally move the beam direction by 20degrees from within the projector housing. We advise that the light be installed 250mmbelow the minimum waterline when the yachtis loaded with 50% fuel and 50% water, andthat the light be angled 15 degrees downwards.To achieve this there are 3 models- Flush, 30 degree and 50 degree.The UL Ti MATE 75 SA has a larger aperturewhich increases the light output by 25%.The stainless steel model comes as standardwith Ice Class Lloyds Approval and has beenpressurised to 80 bar. The aluminium model isIPX8 to 10 bar. The range is also GL Approved.

Lamp Type MSD Metal Halide 150w-250w

Material - Steel and 5083 ALU


Voltage/Amps - 250 watt- 198/264vac- 1.2A

Voltage/Amps - 150 watt 120(V3)/230(V2) - 1.4/0.7.A


NOTEInstallation Instruction:The hole cut-out should be cut to suit the insertangle.Maximum hull plate thickness should be 12mm for the flush and 20mm for the 30 & 50 degree.For Lamp Maintenance allow 170mm behind the cable gland.Electrical Information:150w - Recommended maximum distance between ballast and projector 10m.250w - Recommended maximum distance between ballast and projector 25m.Cable - 150w-250w High temp. silicone 3 core (Part No S00111, 0.75). For additional information please visit our web site.



210mm27mm12

0mm

124m

m

210mm75mm

124m

m

120m

m

210mm105mm

140m

m

40mm

124m

m

UL Ti MATE RANGE - MODEL - UL Ti MATE 75 SA 150W-250W

TECHNICAL SPECIFICATION Order Number Flush-STEEL S00300-75-SA-ICE-V2/V3W2- W1Order Number Flush-ALU S00600-75-SA-V2/V3W2- W1

Order Number 30 deg. STEEL S00330-75-SA-ICE-V2/V3W2-W1Order Number 30 deg. ALU S00630-75-SA-V2/V3W2-W1

Order Number 50 deg. STEEL S00350-75-SA-ICE-V2/V3W2-W1Order Number 50 deg. ALU S00650-75-SA-V2/V3W2-W1

UL Ti MATE 75 SA STEELFlush

UL Ti MATE 75 SA ALU 30 degree

Light Level -150w 12,000 Lumens - 250w 19,000 Lumens

316 S.S. UL Ti MATE 75 SA-ICE‘submersible through hull light’

ORDERING NUMBERS FLUSH - S00300-75-SA-ICE. 30 DEG - S00330-75-SA-ICE. 50 DEG -S00350-75-SA-1CE

WITH 120 (V3) / 230 (V2) VOLT BALLAST AND 150W (W2) OR 250W (V2,W1) WATT LAMP.

The UL Ti MATE 75 SA is serviced from inside the hull. Allow access for maintenance and space for ventilation.Do not use the UL Ti MATE™ in dry-dock or out of waterAllow a minimum of 170mm behind the cable gland for lamp replacements on 150w and 150mm behind the.ignitor on 250w.

Do not attempt to remove the glass lens while afloat.The projector must be correctly assembled with lid secured to the UL Ti MATE™ whilst afloat.


120 & 230 VOLTAGE SUPPLY FOR 150 & 250WATT ELECTRONIC BALLAST COMPLETE

WITH ENCLOSURE .


SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COMUL Ti MATE 75-SA-ICE-SS-H-14-10-2011


Part Description 75-SA Part No1: Projector lid securing plate 00283-B2: M6 Nut 933813: 'O' Ring 001084: Gasket NAF 00285-A5: Connecting ring 00274-C6: Lamp holder screw 002907: Lamp holder (250W) 911957: Lamp holder (150W) 911918: Reflector collar bush 00288-A9: M4 Lock nut 9337410: Lamp (250W) 9120910: Lamp (150W) 9121011: Reflector adjustment rod 0028412: Reflector complete S9179113: Gasket NAF 00285-A14: AB2 Connecting ring 00503-75-A15: Projector barrel 00101-C16: Gasket NAF 000C07-B30: Glass gaskets NAF 00286-A31: Glass lens 0028139: Body Flush (s.s) S00300-75 ICE40: Body 50 deg (s.s.) S00350-75-B ICE41: Body 30 deg (s.s.) S00330-75 ICE42: Glass retaining ring 00304-ICE 75B43: Cap head screws 93334

TM

150 & 250 watt

CABLE SPECIFICATION TO PROJECTORHigh tempereture (180C) silicone

screened three core. Cable diameter 9mmPART NUMBERS00111-180 EWKF 3G0,0.75

ELECTRICAL INFORMATION 150 WATT Maximum distance between ballast and projector -10 meters250 WATT Maximum distance between ballast and projector - 10 meters.Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.ABallast power 250 watt ballast 230 volt, running current 1.2.A

Ballast will not ignite a hot lamp. The ballast has a cycle of three atemptsto ignite the lamp then will wait for six minutes before repeating the cycle.

Ballast must be installed in dry space. Maximum ambient temperature 40CDO NOT swich ballast on and off.

FLUSH

S00350-75 ICE (40)

S00300-75 ICE (39)

S00330-75 ICE (41)Part Description 75-SA Part No22: Gland 9201123: Projector cover 00102-E24: Ballast 250 watt 230v S00820-V2 W124: Ballast 150 watt 230v S00800-V2W224: Ballast 150 watt 120v S00800-V3W2


Ballast

UL Ti MATE™ to be fitted a minimumof 250mm below the yachts water line when loaded with 50% fuel and 50% freshwater onboard

ELECTRICAL INFORMATION 150 WATT Maximum distance between ballast and projector -10meters250 WATT Maximum distance between ballast and projector - 25 meters.Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.ABallast power 250 watt ballast 230 volt, running current 1.2.ABallast will not ignite a hot lamp. The ballast has a cycle of three atemptsto ignite the lamp then will wait for six minutes before repeating the cycle.

Ballast must be installed in dry space. Maximum ambient tmperature 40CDO NOT switch ballast on and off.

5083 ALU UL Ti MATE 75 SA‘submersible through hull light’

ORDERING NUMBERS FLUSH - S00600-75-SA. 30 DEG - S00630-75-SA. 50 DEG - S00650-75-SA

WITH 120 (V3) / 230 (V2) VOLT BALLAST AND 150W (W2) OR 250W (V2,W1) WATT LAMP.

The UL Ti MATE 75 SA is serviced from inside the hull. Allow access for maintenance and space for ventilation.Do not use the UL Ti MATE™ in dry-dock or out of waterAllow a minimum of 170mm behind the cable gland for

.....lamp replacements on 150w and 150mm behind the.ignitor

.....on 250wUL Ti MATE™ to be fitted 250mm below the yachts water line when loaded with 50% fuel and 50% freshwater onboard.

Do not attempt to remove the glass lens while afloat.The projector must be correctly assembled with lid secured to the UL Ti MATE™ whilst afloat.


150 WATT ELECTRONIC BALLAST COMPLETEWITH ENCLOSURE. SEE

BALLAST SHEET FOR FURTHER INFORMATION


SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COMUL Ti MATE 75-SA-ALU-H-14-10-2011



Ballast S00801-V2/V3

Part Description 75-SA Part No1: Projector lid securing plate 00283-B2: M6 Nut 933813: 'O' Ring 001084: Gasket NAF 00285-A5: Connecting ring 00274-C6: Lamp holder screw 002907: Lamp holder (250W) 911957: Lamp holder (150W) 911918: Reflector collar bush 00288-A9: M4 Lock nut 9337410: Lamp (250W) 9120910: Lamp (150W) 9121011: Reflector adjustment rod 002842-12: Reflector complete S9179113: Gasket NAF 00285-A14: AB2 Connecting ring 00503-75A15: Projector barrel 00101-D16: Gasket NAF 000C07-B30: Glass gaskets NAF 00286-A31: Glass lens 0028139: Body Flush (alu) S00600-7540: Body 50 deg (alu) S00650-75-B41: Body 30 deg (alu) S00630-7542: Glass retaining ring 00604-75-B43: Cap head screws 93460-SC

Part Description 75-SA Part No22: Gland 9201023: Projector cover 00102-E24: Ballast 250 watt S00820-V2W124: Ballast 150 watt 230v S00800-V2W224: Ballast 150 watt 120v S00800-V3W2

TM

150-250 watt

CABLE SPECIFICATION TO PROJECTHigh temp silicone three core part number. S00111

FLUSH

S00600-75

S00650-75

S00650-75

ul ti mate ™ range of underwater lights™ ti mate ™ range of underwater lights™ ... ul ti...

Documents