pedestal mounts - lord
TRANSCRIPT
Toll-Free: +1 877 ASK LORD (275 5673) | E-mail: [email protected] LORD.COM 4LORD.COM 102
NEW HIGHLY DAMPED ELASTOMERIC ISOLATORS
Designed to protect delicate electronic equipment from damaging shock and vibration, these isolators are widely used in jet aircraft, missile, spacecraft and related ground support equipment. The low-profile design requires a minimum of headroom. Installation is simple; no special openings or tools are needed. Bonded in BTR® elastomer, these mounts have high damping and wide operating temperature range.
Features:
• Rated load range: 8 to 60 lb (3.6 to 27 kg)
• Maximum amplification at resonance: 2.5 to 4, depending on vibration environment
• Operating temperature range: -65°F to +300°F (-54°C to +149°C)
• Gradual snubbing under shock load
• Accommodate vibratory inputs up to 0.06 inch D.A.
• Sustain a 15g, 11ms, half-sine shock pulse without significant change in performance and a 30g, 11ms, half-sine pulse without failure
Benefits:
• Fully bonded: precise, predictable and reliable performance over a wide range of vibration disturbances
• All-attitude performance: axial and radial static and dynamic characteristics nearly the same, can be loaded in any direction
• Fail safe: mechanical interlock keeps equipment in place in the event of elastomeric failure
PEDESTAL MOUNTSPS SERIES
FIGURE 1 – TYPICAL INSTALLATION
Toll-Free: +1 877 ASK LORD (275 5673) | E-mail: [email protected]
FIGURE 1 – PART DIMENSIONS
FIGURE 2 – LOAD VS. DEFLECTION
FIGURE 3 – TRANSMISSIBILITY VS. FREQUENCY
• Materials: Metal parts and finish – aluminum alloy, chromate treated per MIL-DTL-5541, Class 1A
Inner member – 2024-T3 aluminum
Other metal parts – 2024-T3 aluminum
• Load capacity: 8 to 50 lb (3.6 to 27 kg)
• Mount weight for all variations: 3.0 oz (85 g) max
TABLE 1 – PERFORMANCE CHARACTERISTICS
Part Number
Load Range Nominal Dynamic
Axial Frequency
– fn (Hz)
Dynamic Axial Spring Rate
Dynamic Radial Spring Rate
lb kg lb/in N/mm lb/in N/mm
PS1010 8-12 3.6-5.4 25 638 112 638 112
PS1015 13-19 5.9-8.6 25 957 167 957 167
PS1025 20-28 9.1-13 25 1595 279 1595 279
PS1035 29-41 13-19 25 2233 391 2233 391
PS1050 42-50 19-27 25 3190 558 3190 558
Ordering Information:Although aluminum components are considered standard, pedestal mounts with steel components may also be ordered. A suffix letter “A” designates aluminum and letter “S” designates steel.All variations of pedestal mount are available with either a through hole or a tapped hole in the center of the mount. The standard size is 1/4 in (6.35 mm). The type of hole is indicated by a suffix.Explanation of part numbering system:P S 10 15 - A - 8
* Other materials available as specials only.
0.01
0.1
1
10
1 10 100 1000
Tran
smis
sibi
lity
(T)
Frequency (Hz)
300F
70F
-65F
Metric values in parenthesis.
PEDESTAL MOUNTSPS SERIES
Ø2.29 2.27 (58.2) (57.6)
Ø.211 .199 (5.36) (5.05)
R .24 .22 (6.1) (5.6)
2.39 2.37 (60.7) (60.2)
1.94 (49.2)
.97 (24.6)
1.14 1.11 (29.0) (28.2)
.086
.074 (2.18) (1.88)
.24
.21 (6.1) (5.3)
THRU OR TAPPED (HOLE) (SEE ORDERING INFORMATION)
)
-8 1/4 in (6.35 mm) diameter through hole 1/4-28 UNF-2B hole (tapped through)A = aluminum components*Nominal load rating (lb)Mount series (1000)Silicone elastomer (LORD BTR®)Pedestal Type
0
200
400
600
800
1000
1200
1400
1600
0.0 1.0 2.0 3.0 4.0 5.0 6.0
0
50
100
150
200
250
300
350
400
0.00 0.05 0.10 0.15 0.20 0.25
Load
(N)
De�ection (mm)
Load
(lbs
)
De�ection (in)
PS1010PS1015PS1025PS1035PS1050
Ø 2.292.27
(58.2)(57.7)
1.141.11
(29.0)(28.2)
.09
.07(2.3)(1.8)