petrol power washer - machine mart

28
OPERATION & MAINTENANCE INSTRUCTIONS LS0413 PETROL POWER WASHER MODEL NO: PLS190N, PLS260N PART NO: 7330345, 7330355

Upload: others

Post on 24-May-2022

3 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: PETROL POWER WASHER - Machine Mart

PETROL POWER WASHERMODEL NO: PLS190N, PLS260N

PART NO: 7330345, 7330355

OPERATION & MAINTENANCEINSTRUCTIONS

LS0413

Page 2: PETROL POWER WASHER - Machine Mart

P

INTRODUCTION

Thank you for purchasing this CLARKE Petrol Power Washer.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

UNPACKING

Unpack your power washer and check to ensure the following items are present. Contact your Clarke dealer immediately if any parts are missing or damaged.

Power Washer Delivery Hose

Gun Assembly Lance / Nozzle Assembly

2 x Wheels 2 x Rubber Foot

Inlet Hose Detergent Hose

2 x Axle Tommy Bar

Hose / Lance Storage Bracket Spark Plug Box Spanner

Pump Vent Assembly Separate engine manual

2arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 3: PETROL POWER WASHER - Machine Mart

3Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

GUARANTEE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY SYMBOLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

BEFORE USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

USING YOUR POWER WASHER . . . . . . . . . . . . . . . . . . . . 12

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

EXPLODED DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

PARTS LIST PLS190N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

PARTS LIST PLS260N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PLS190N DECLARATION OF CONFORMITY PAGE 1. . . . 25

PLS260N DECLARATION OF CONFORMITY PAGE 1. . . . 26

DECLARATION OF CONFORMITY PAGE 2 . . . . . . . . . . . 27

Page 4: PETROL POWER WASHER - Machine Mart

4Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY RULES

1. NEVER direct the spray towards any person or animal.

2. NEVER direct the spray towards electrical wiring or equipment.

3. NEVER hold your finger over the high pressure nozzle.

4. NEVER allow children to use this machine.

5. NEVER operate the machine with any of the covers removed.

6. NEVER attempt any repairs to this machine always refer to a qualified service agent.

7. NEVER supply any liquid other than water to the water inlet.

8. NEVER use the chemical injection facility to introduce solvents, e.g. paint thinners, petrol, oil etc.

9. ALWAYS release any residual pressure in the system by turning off the water supply and operating the trigger before disconnecting any hose or accessory.

10. ALWAYS keep the machine itself dry and well clear of water spray

11. ALWAYS wear protective clothing and safety glasses. Loose particles and other debris may be propelled at high speed by the water jet.

12. ALWAYS grip the gun firmly before pressing the trigger, expect the gun to ‘kick’ when starting.

13. ALWAYS respect the requirements of the local water company. Power washers may only be connected to the mains drinking water supply, if a backflow preventer valve is installed in the supply hose.

14. When not in use, ALWAYS disconnect from the water supply, and ensure the system is completely drained. Store in a cool dry location.

15. When using the chemical injection facility, use only the chemical cleaning agents (detergents), that are approved for power washers. CLARKE Traffic Film Remover or CLARKE Wash and WAX (available from your dealer), is recommended.

16. Refuel in a well ventilated area with the engine switched off.

17. Do not use or refuel near naked flames.

WARNING: Water at high pressure can be dangerous and can cause damage to persons or property if the operator is careless. Never allow anyone to operate this equipment unless they are thoroughly reliable, and familiar with the safety precautions.

Page 5: PETROL POWER WASHER - Machine Mart

5Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY SYMBOLS

ALWAYS: Read this manual. Understand all warnings and instructions before operating this equipment.

DANGER: Risk of fire or explosion. Shut off engine before adding fuel. Keep work area free of combustible materials. Do not spray flammable liquids.

DANGER: Risk to breathing. Engine exhaust fumes can kill. For outdoor use only. Work in a well ventilated area.

WARNING: Risk of injection or severe injury. Do not direct discharge stream at persons or animals. Keep clear of nozzle. This machine is to be used only by qualified operators.

WARNING: Risk of spray injury. Spray can propel objects. Always wear ANSI approved Z87.1 Safety Glasses.

WARNING: Risk of chemical burn. Never spray acids, corrosive or toxic chemicals. Use only cleaners formulated for power washers.

WARNING: Risk of electrocution. Never direct spray toward any electrical device or electrical outlet.

WARNING: R i s k o f unsafe operat ion . Keep children away from this equipment. Gun kicks back. Hold with both hands.

WARNING: Risk of hot surfaces. Avoid contact with hot engine exhaust components. Don't allow hoses to contact the engine muffler during or after use.

Page 6: PETROL POWER WASHER - Machine Mart

6Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

OVERVIEW

12

10

4

56

7

8

9

3

11

NO DESCRIPTION NO DESCRIPTION

1 Gun/lance 7 High pressure hose

2 Spray wand 8 Foldable handle

3 Engine 9 Pressure regulator

4 Adjustable nozzle 10 Engine starter

5 Wheels 11 Throttle

6 Chemical detergent hose

Page 7: PETROL POWER WASHER - Machine Mart

P

ASSEMBLY

CONNECTING THE WHEELS1. Remove the nut, spring washer

and washer from the axle.

2. Fit the axles into the axle ports as shown, secure with the nut, spring washer and flat washer.

3. Fit the wheels to the axles and secure with the nut and washer.

NOTE: Do not overtighten the nuts, the wheels must be able to rotate freely.

RUBBER FEET

1. Fit the rubber feet to the legs as shown.

ASSEMBLE THE LANCE1. Connect the spray wand to the

lance and tighten securely.

7arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 8: PETROL POWER WASHER - Machine Mart

P

THE HIGH PRESSURE HOSE

CONNECT THE HOSE TO THE GUN

1. Slide the connector on the hose backwards.

2. Push the gun into the connector.

3. Release the connector.

NOTE: Make sure the connection is secure.

CONNECT THE HOSE TO THE POWER WASHER

1. Slide the connector on the power washer towards the machine.

2. Push the hose into the connector.

3. Release the connector.

NOTE: Make sure the connection is secure.

CONNECT WATER INLET HOSE 1. Remove the travel cap if fitted.

2. Connect the water supply hose to the water inlet.

NOTE: Water source must provide a minimum of 5 gallons per minute at 20 p.s.i.

NOTE: Make sure the water inlet hose is screwed on tightly.

HOSE / LANCE STORAGE BRACKET1. Fit the bracket into the position

shown and secure using the washers and nuts supplied

8arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 9: PETROL POWER WASHER - Machine Mart

P

REMOVE THE TRAVEL PLUG BEFORE USE.1. Remove the red travel plug.

2. Inside the small bag attached is an oil filler cap which needs to be fitted in its place.

BEFORE USE

IMPORTANT: The engine is supplied without any oil in it and must be filled to the correct level before use, see below.

CHECKING THE PUMP OIL LEVELLook at the sight glass on the pump to check the oil level inside.

If required, remove the oil filler cap and top up with oil.

• We recommend the use of SAE30 oil in this pump.

CHECKING THE ENGINE OIL LEVEL1. Turn the oil filler cap/dipstick anti-

clockwise and remove it from the oil filler tube, wipe the dipstick with a clean cloth.

2. Insert the oil filler cap/dipstick back into the oil filler tube and then remove it again. Do not screw it in when doing this.

WARNING: TO CARRY OUT THIS CHECK, PLACE THE POWER WASHER ON LEVEL GROUND WITH THE ENGINE SWITCHED OFF.

WARNING: TAKE CARE NOT TO TOUCH ANY HOT PARTS OF THE POWER WASHER WHEN CHECKING THE OIL LEVELS.

SIGHT GLASS

DRAIN CAP

OIL FILLER CAP

9arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 10: PETROL POWER WASHER - Machine Mart

P

3. If the oil is low, fill the oil reservoir to the edge of the oil filler hole.

• We recommend the use of SAE30 oil in the engine.

4. Replace the oil filler cap.

CAUTION: RUNNING THE ENGINE WITH INSUFFICIENT OIL CAN CAUSE ENGINE DAMAGE.

CHECKING THE FUEL LEVEL1. To check the fuel level, remove the fuel tank cap.

2. Just inside the fuel tank is a fuel strainer. Check this filter periodically and remove any contaminants which may have accumulated.

3. Refuel in a well-ventilated area, before starting the engine. If the engine has been running, allow it to cool. Refuel carefully to avoid spilling fuel. Do not fill above the fuel strainer shoulder.

4. After refueling, Replace the fuel filler cap securely.

RECOMMENDED FUELUse unleaded petrol with an octane rating of 86 or higher. Do not overfill.

WARNING: ALWAYS REFUEL IN A WELL VENTILATED AREA AWAY FROM ANY HEAT SOURCES.

WARNING: ALLOW THE UNIT TO COOL DOWN BEFORE REFUELLING.

WARNING: DO NOT LEAVE FUEL WITHIN THE REACH OF CHILDREN.

10arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 11: PETROL POWER WASHER - Machine Mart

P

PRESSURE REGULATORWhen supplied, the pressure regulator may be set to minimum.

Turn the pressure regulator on the pump fully clockwise to allow water pressure to build up when the pressure washer is running.

If you find the pressure is too high, you can adjust this later.

11arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 12: PETROL POWER WASHER - Machine Mart

P

USING YOUR POWER WASHER

POWER WASHER TERMINOLOGYPSI: Pounds per square inch, the unit of measurement for water pressure.

GPM: Gallons per minute.

CU: Cleaning units, GPM x PSI.

Bypass mode: In bypass mode, the pump recirculates the water because the trigger of the spray gun is not being pulled. If unit is left in bypass mode for more than two minutes, the water temperature will rise to a dangerous level and could damage internal components of the pump.

NOTE: Any damage to the pump due to these causes will not be covered under warranty.

Thermal Relief Valve: In an effort to prevent extreme damage, pumps are equipped with a thermal relief valve. This valve will open when the temperature inside the pump becomes too high. This valve will then release a gush of water in an effort to lower the temperature inside the pump. Immediately after this occurs, the valve will close.

Chemical Injection System: This mixes cleaners or cleaning solvents with the pressurised water to improve cleaning effectiveness.

12arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 13: PETROL POWER WASHER - Machine Mart

P

STARTING THE POWER WASHERPrior to starting, refer to your engine manual for proper starting procedures for your engine type.

1. Make sure the engine has sufficient fuel. See page 10.

2. Check engine oil level. See page 9.

3. Turn water supply on.

4. Start the engine. See Engine Owners Manual for correct procedure.

NOTE: If the engine does not start after two pulls, pull the trigger on the gun to relieve the pressure.

5. Pull the trigger on the gun to start water flow.

• Stand on a stable surface and grip gun/spray wand firmly with both hands.

• Expect the gun to kick when the trigger is pulled.

6. Release trigger to stop water flow.

NOTE: The power washer will automatically go into bypass mode, in bypass mode, the pump recirculates the water because the trigger of the spray gun is not being pulled. If unit is left in bypass mode for more than two minutes, the water temperature will rise to a dangerous level and could damage internal components of the pump.

WARNING: FAILURE TO TURN ON THE WATER COULD CAUSE DAMAGE TO THE PUMP.

WARNING: DO NOT ALLOW UNIT TO OPERATE IN BYPASS MODE FOR MORE THAN TWO MINUTES AT ANY TIME.

13arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 14: PETROL POWER WASHER - Machine Mart

P

ADJUSTING THE SPRAYThe nozzle is adjustable to allow you to change the spray from a narrow jet of water to a wide spray.

To adjust the nozzle, proceed as follows.

1. Hold the shaft of the lance in one hand.

2. Twist the nozzle with the other hand.

3. To vary the spray between narrow and wide, turn the nozzle counter-clockwise through a half-of-a-turn.

ADJUSTING THE PRESSURE1. Adjust the pressure regulator on

the pump. Turn the pressure regulator knob counter clockwise to lower pressure. Once you have finished using your power washer, return the pressure regulator to its original position.

2. Back away from the surface to be cleaned. The further away you are the less the pressure will be on the surface being cleaned.

3. Reduce the speed of the engine (RPM). Slow the engine down and the water pressure will also go down.

4. Adjust the spray to a wider angle.

5. Slide the nozzle forward for low pressure and backwards for high pressure.

14arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 15: PETROL POWER WASHER - Machine Mart

P

APPLYING CHEMICALS AND CLEANING SOLVENTS1. Push the chemical hose onto the

ridged fitting as shown.

2. Place the other end of the chemical hose with the filter on it, into a container holding the chemical/cleaning solution.

3. Slide the nozzle forward for low pressure operation.

• The water/chemical ratio is typically 7:1, for every 7 gallons of water pumped 1 gallon of chemical/ cleaning solution will be used.

SHUTTING DOWN1. After each use, if you have applied chemicals, place the chemical hose

into a container of clean water and run clean water through the chemical injection system to flush the system thoroughly.

NOTE: Failure to do so could cause damage to the pump.

2. Turn the engine off. See engine owner's manual.

NOTE: NEVER turn the water off with the engine running.

3. Turn the water supply off.

4. Pull the trigger on the spray gun to relieve any water pressure.

5. See storage section in this manual for proper storage procedures.

15arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 16: PETROL POWER WASHER - Machine Mart

P

MAINTENANCE

CHANGING THE PUMP OIL

1.

CRANKCASE

DRAIN PLUG

OIL FILLER CAP

SIGHT GLASS

Unscrew and remove the oil filler cap.

2. Place an oil collection tray (not supplied) under the drain plug.

3. Unscrew the drain plug, and allow the used oil to drain from the crankcase into the oil collection tray.

NOTE: Drain the oil when the engine is warm, this will ensure the oil flows out quicker.

4. Replace the drain plug and its ring seal.

5. With the power washer in a level position, fill to the centre of the sight glass with the recommended oil.

6. Replace the oil filler cap.

ENVIRONMENTAL PROTECTIONOne of the most damaging sources of pollution is oil. Do not throw away used oil with your domestic rubbish or down drains and sinks. Place it in a leak proof container and take it to you local waste disposal site.

CAUTION: PROLONGED EXPOSURE TO USED OIL IS DANGEROUS, ALWAYS WASH YOUR HANDS THOROUGHLY AFTER HANDLING USED OIL.

16arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 17: PETROL POWER WASHER - Machine Mart

P

CLEANING THE NOZZLEif the nozzle becomes partially clogged or restricted by dirt or other foreign material, excess pump pressure may develop. Clean the nozzle immediately by following the instructions below.

1. Shut off the power washer and turn off the water supply.

2. Pull the trigger on the gun handle to relieve any water pressure.

3. Disconnect the spray wand from the gun.

4. Remove any obstructions and back flush with clean water.

5. Direct the water supply into the spray wand end for 30 seconds to back flush loosened particles.

6. Reconnect the spray wand to the gun and turn on the water supply.

CLEANING THE WATER INLET This water inlet should be checked periodically and cleaned if necessary.

17arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 18: PETROL POWER WASHER - Machine Mart

P

STORAGE

ENGINESee the separate engine manual supplied for information regarding the storage procedure.

PUMP1. Drain all water from the high pressure hose, coil it and store it on the gun/

hose holder located on the side of the power washer handle.

2. Drain all water from the spray gun and spray wand by holding the gun/wand vertically with the nozzle pointing down and pulling the trigger. Store in the gun/hose holder.

3. Store all other parts so that they are protected from damage.

STORAGE PROCEDUREFor long term storage, the petrol tank should be drained. Ensure that the engine is cold before draining the tank. Remove the fuel tank cap and use a pump type syphon to drain the petrol into an appropriate, clean container.

Do not store petrol for long periods of time.

Dispose of excess petrol in an environmentally safe way. Your local recycling centre can advise you on the best method of disposal. After the petrol tank has been drained, start the engine and allow it to use any petrol that may remain in the engine or fuel pipe. Make sure that the power washer has been thoroughly cleaned before storing it in a clean dry place.

18arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 19: PETROL POWER WASHER - Machine Mart

P

TROUBLESHOOTING

If the following does not solve your problem, please contact the CLARKE service department.

PROBLEM CAUSE SOLUTION

Engine will not start (see engine manual for further engine troubleshooting)

No fuel Add fuel

Low oil Add oil

Pressure builds up after two pulls on the recoil starter or after initial use

Squeeze the gun trigger to relieve the pressure

Spark plug wire not attached correctly

Attach the spark plug wire

Engine switch is in the OFF position

Set the engine switch to the ON position

Choke lever is set to the choke position when the engine is warm

Set the choke lever to the NO CHOKE position

Fuel valve closed Open the fuel valve

Lack of pressure (initial use)

Water supply is not adequate

Make sure your water supply can deliver 5 gallons per minute at 20psi

Leak in the high pressure hose fitting

Tighten the fitting, use sealant tape if required

Nozzle is obstructed Clear the nozzle

Water filter screen is clogged

Remove and clean the filter

Defective E-Z start valve Have it replaced by your dealer

Air in the supply hose Turn off the engineTurn off the water supply, Disconnect the water supply from the pump inlet and turn on the water to expel the air from the hose. When all the air has been removed, turn off the water supply and reconnect the hose. Turn on the water supply and pull the trigger to expel any air in the gun/wand

19arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 20: PETROL POWER WASHER - Machine Mart

P

No or low pressure (initial use) continued

Choke lever is in the CHOKE position

Move the choke lever to the NO CHOKE position

Throttle control lever is not in the fast position

Move the throttle control lever to the fast position

High pressure hose is too long

Make sure the high pressure hose is under 100 feet

Will not draw chemicals

Chemical filter is blocked Clean the filter

Chemicals being used are too thick

Dilute the chemicals. The chemicals should have the consistency of water

High pressure hose is too long.

Use a longer supply hose instead of a longer high pressure hose

Chemical build up inside the chemical injector

Have the parts cleaned or replaced by your dealer

No or low pressure (after a period of normal use)

Worn seal or packing Have it replaced by your dealer

Worn or obstructed valves

Have it replaced by your dealer

Worn unloader piston Have it replaced by your dealer

Worn E-Z start valve Have it replaced by your dealer

Water leaking at the gun / spray wand connection

Worn or broken O-ring Check and replace

Loose hose connection Tighten

Water leaking at the pump

Loose connections Tighten

Piston packings worn Have it replaced by your dealer

Worn or broken O-rings Have it replaced by your dealer

Pump head or tubes damaged from freezing

Have it replaced by your dealer.

Oil leaking at the pump

Oil seals worn Have it replaced by your dealer

Loose drain plug Tighten

Worn O-rings Check and replace

Pump pulsates Nozzle obstructed Clear the nozzle

PROBLEM CAUSE SOLUTION

20arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 21: PETROL POWER WASHER - Machine Mart

21Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SPECIFICATIONS

Model PLS190N PLS260N

Engine

Engine Model 200F(D) 390F(D)

Power (HP) 6.5 13

Engine type Petrol (unleaded)

Starting system Recoil Recoil

Fuel Capacity (L) 3.5 6

Water supply

Max. feed temperature 50oC 50oC

Min. feed volume 5 gallons per minute at 20 PSI

Performance Data

Working pressure 165 Bar 235 Bar

Max. permissible pressure 186 Bar 260 Bar

Max. water flow (l/min.) 12.6 16.5

Measured sound power level LWA dB

102.5 111

Guaranteed sound power level LWA dB

105 114

Dimensions

Length (mm) 950 1075

Width (mm) 590 660

Height (mm) 620 760

Weight (kg) 48 60.5

Page 22: PETROL POWER WASHER - Machine Mart

P

EXPLODED DIAGRAM

22arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 23: PETROL POWER WASHER - Machine Mart

P

PARTS LIST PLS190N

1 Drain Plug RKPLS190N01

2 Gasket RKPLS190N02

3 Screw RKPLS190N03

4 Crankcase Cover RKPLS190N04

5 O-ring RKPLS190N05

6 Side Glass RKPLS190N06

7 Fixing Clip RKPLS190N07

8 O-Ring RKPLS190N08

9 Vented Oil Plug RKPLS190N09

10 O-Ring RKPLS190N10

11 Bolt RKPLS190N11

12 Crankshaft Cover RKPLS190N12

13 O-Ring RKPLS190N13

14 Snap Ring RKPLS190N14

15 Ball Bearing RKPLS190N15

16 Crankshaft RKPLS190N16

17 Connecting Rod RKPLS190N17

18 Fixing Pin RKPLS190N18

19 Ceramic Plunger RKPLS190N19

20 Crankcase RKPLS190N20

21 Needle Bearing RKPLS190N21

22 Flange RKPLS190N22

23 Oil Seal RKPLS190N23

24 Bolt RKPLS190N24

25 Oil Seal RKPLS190N25

26 Retainer Ring RKPLS190N26

27 O-Ring RKPLS190N27

28 Low Pressure Seal RKPLS190N28

29 Seal Compaction Ring RKPLS190N29

30 Compression Washer RKPLS190N30

31 High Pressure Seal RKPLS190N31

32 Supporting Ring RKPLS190N32

33 Plastic Cap RKPLS190N33

34 Knob RKPLS190N34

35 Spring RKPLS190N35

36 Spring Seat RKPLS190N36

37 Jam Nut RKPLS190N37

38 Fixing Screw RKPLS190N38

39 Unloader Valve RKPLS190N39

40 Valve Seat RKPLS190N40

41 O-Ring RKPLS190N41

42 O-Ring RKPLS190N42

2arts & Service: 020 8988 7400 / E-mail: Parts@clarke

43 Valve Housing RKPLS190N43

44 Soap Suction Nozzle RKPLS190N44

45 O-Ring RKPLS190N45

46 Steel Ball RKPLS190N46

47 Spring RKPLS190N47

48 Valve Plug RKPLS190N48

49 Spring RKPLS190N49

50 Steel Ball RKPLS190N50

51 O-Ring RKPLS190N51

52 Outlet Banjo Bolt RKPLS190N52

53 O-Ring RKPLS190N53

54 O-Ring RKPLS190N54

55 Checking Valve RKPLS190N55

56 Spring RKPLS190N56

57 O-Ring RKPLS190N57

58 Outlet Quick Connector RKPLS190N58

59 Inlet Banjo Bolt RKPLS190N59

60 O-Ring RKPLS190N60

61 Bypass Housing RKPLS190N61

62 Swivel Nut RKPLS190N62

63 Inlet Connector RKPLS190N63

64 Inlet Water Filter RKPLS190N64

65 O-Ring RKPLS190N65

66 Valve Plug RKPLS190N66

67 O-Ring RKPLS190N67

68 Checking Valve Assy RKPLS190N68

69 O-Ring RKPLS190N69

70 Outlet Plug RKPLS190N70

71 Inlet Plug RKPLS190N71

72 Bolt RKPLS190N72

73 Manifold Head RKPLS190N73

74 Filter RKPLS190N74

75 Chemical Inlet Hose RKPLS190N75

76 Pump Fix Bolt RKPLS190N76

77 Pump Assy RKPLS190N77

78 High-pressure Hose RKPLS190N78

79 Gun RKPLS190N79

80 Wand RKPLS190N80

81 Rubber Foot RKPLS190N81

82 Water Inlet Hose RKPLS190N82

83 Wheel RKPLS190N83

3international.com or [email protected]

Page 24: PETROL POWER WASHER - Machine Mart

P

PARTS LIST PLS260N

1 Drain Plug RKPLS260N01

2 Gasket RKPLS260N02

3 Screw RKPLS260N03

4 Crankcase Cover RKPLS260N04

5 O-ring RKPLS260N05

6 Side Glass RKPLS260N06

7 Fixing Clip RKPLS260N07

8 O-Ring RKPLS260N08

9 Vented Oil Plug RKPLS260N09

10 O-Ring RKPLS260N10

11 Bolt RKPLS260N11

12 Crankshaft Cover RKPLS260N12

13 O-Ring RKPLS260N13

14 Snap Ring RKPLS260N14

15 Ball Bearing RKPLS260N15

16 Crankshaft RKPLS260N16

17 Connecting Rod RKPLS260N17

18 Fixing Pin RKPLS260N18

19 Ceramic Plunger RKPLS260N19

20 Crankcase RKPLS260N20

21 Needle Bearing RKPLS260N21

22 Flange RKPLS260N22

23 Oil Seal RKPLS260N23

24 Bolt RKPLS260N24

25 Oil Seal RKPLS260N25

26 Retainer Ring RKPLS260N26

27 O-Ring RKPLS260N27

28 Low Pressure Seal RKPLS260N28

29 Seal Compaction Ring RKPLS260N29

30 Compression Washer RKPLS260N30

31 High Pressure Seal RKPLS260N31

32 Supporting Ring RKPLS260N32

33 Plastic Cap RKPLS260N33

34 Knob RKPLS260N34

35 Spring RKPLS260N35

36 Spring Seat RKPLS260N36

37 Jam Nut RKPLS260N37

38 Fixing Screw RKPLS260N38

39 Unloader Valve RKPLS260N39

40 Valve Seat RKPLS260N40

41 O-Ring RKPLS260N41

42 O-Ring RKPLS260N42

2arts & Service: 020 8988 7400 / E-mail: Parts@clarke

43 Valve Housing RKPLS260N43

44 Soap Suction Nozzle RKPLS260N44

45 O-Ring RKPLS260N45

46 Steel Ball RKPLS260N46

47 Spring RKPLS260N47

48 Valve Plug RKPLS260N48

49 Spring RKPLS260N49

50 Steel Ball RKPLS260N50

51 O-Ring RKPLS260N51

52 Outlet Banjo Bolt RKPLS260N52

53 O-Ring RKPLS260N53

54 O-Ring RKPLS260N54

55 Checking Valve RKPLS260N55

56 Spring RKPLS260N56

57 O-Ring RKPLS260N57

58 Outlet Quick Connector RKPLS260N58

59 Inlet Banjo Bolt RKPLS260N59

60 O-Ring RKPLS260N60

61 Bypass Housing RKPLS260N61

62 Swivel Nut RKPLS260N62

63 Inlet Connector RKPLS260N63

64 Inlet Water Filter RKPLS260N64

65 O-Ring RKPLS260N65

66 Valve Plug RKPLS260N66

67 O-Ring RKPLS260N67

68 Checking Valve Assy RKPLS260N68

69 O-Ring RKPLS260N69

70 Outlet Plug RKPLS260N70

71 Inlet Plug RKPLS260N71

72 Bolt RKPLS260N72

73 Manifold Head RKPLS260N73

74 Filter RKPLS260N74

75 Chemical Inlet Hose RKPLS260N75

76 Pump Fix Bolt RKPLS260N76

77 Pump Assy RKPLS260N77

78 High-pressure Hose RKPLS260N78

79 Gun RKPLS260N79

80 Wand RKPLS260N80

81 Rubber Foot RKPLS260N81

82 Water Inlet Hose RKPLS260N82

83 Wheel RKPLS260N83

4international.com or [email protected]

Page 25: PETROL POWER WASHER - Machine Mart

P

PLS190N DECLARATION OF CONFORMITY PAGE 1

25arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 26: PETROL POWER WASHER - Machine Mart

P

PLS260N DECLARATION OF CONFORMITY PAGE 1

26arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 27: PETROL POWER WASHER - Machine Mart

P

DECLARATION OF CONFORMITY PAGE 2

27arts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Page 28: PETROL POWER WASHER - Machine Mart