peugeot bsi reset

Process of Rebooting BSI in Peugeot: Method for starting the BSI: The very first step is to unplug the diagnostic tool from the vehicle. 1. Make sure all the gadgets are switched off, the driver’s window lowered down and open the bonnet. 2. Then close all the doors and take off the key from ignition. 3. After a 3 minute interval, unplug the vehicle’s battery terminals and wait for a further 15 seconds. 4. Attach back the battery terminals and give a 10 second pause making sure the doors are closed. 5. Turn the side lights on. 6. Now turn the engine on and inspect the system functioning. 7. Press and hold down the lock button on the key for 10 seconds. 8. Check the central locking system by unlocking and locking the door consecutively. 9. Turn the engine on again and finish i nspecting the system. Following any other procedure could cause malfunctioning of different units which depend on BSI. Method for unplugging the battery: Before unplugging the battery, turn off all gadgets and lights, closing all the doors and unplugging any kind of diagnostic tool. The drivers side window has to be kept open for any kind of requirement. 1. Turn off the ignition and take out the key following which unplug the battery after an interval of 3 minutes. 2. The BSI needs to be taken to Sleep mode or Active Economy mode, during which nothing in the vehicle should be operating. Even the bonnet should not be opened that time as it can ‘wake up’ the BSI if the vehicle has got an alarm installed. For batteries under the bonnet, the bonnet should be opened and left up before allowing the BSI to go to Sleep Mode. During this 3 minute interval, use of any remote control central locking gadgets for other vehicles should be avoided in the vicinity of the concerned vehicle. Method for connecting the battery The following procedure is for reinstalling the battery connection unless told otherwise by Peugeot or Product service. Failure to follow this procedure may result in damage to the BSI’s embedded software during reconnection. 1. All the doors have to be closed w ith the ignition key turned off and the key taken out. 2. Now without opening the doors, replug the battery and wait for 10 seconds. 3. Turn on the headlights, turn on the engine and inspect the system’s functioning.

Upload: guta8119

Post on 09-Feb-2018

214 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Process of Rebooting BSI in Peugeot:

Method for starting the BSI:

The very first step is to unplug the diagnostic tool from the vehicle.

1. Make sure all the gadgets are switched off, the driver’s window lowered down and open thebonnet.

2. Then close all the doors and take off the key from ignition.3. After a 3 minute interval, unplug the vehicle’s battery terminals and wait for a further 15

seconds.4. Attach back the battery terminals and give a 10 second pause making sure the doors are

closed.5. Turn the side lights on.6. Now turn the engine on and inspect the system functioning.7. Press and hold down the lock button on the key for 10 seconds.8. Check the central locking system by unlocking and locking the door consecutively.9. Turn the engine on again and finish inspecting the system.

Following any other procedure could cause

malfunctioning of different units which depend

on BSI.

Method for unplugging the battery:

Before unplugging the battery, turn off all gadgets and lights, closing all the doors and unplugging

any kind of diagnostic tool. The drivers side window has to be kept open for any kind ofrequirement.

1. Turn off the ignition and take out the key following which unplug the battery after an interval of 3minutes.

2. The BSI needs to be taken to Sleep mode or Active Economy mode, during which nothing inthe vehicle should be operating. Even the bonnet should not be opened that time as it can‘wake up’ the BSI if the vehicle has got an alarm installed. For batteries under the bonnet, thebonnet should be opened and left up before allowing the BSI to go to Sleep Mode. During this 3minute interval, use of any remote control central locking gadgets for other vehicles should beavoided in the vicinity of the concerned vehicle.

Method for connecting the battery

The following procedure is for reinstalling the battery connection unless told otherwise by Peugeot or

Product service. Failure to follow this procedure may result in damage to the BSI’s embedded software

during reconnection.

1. All the doors have to be closed with the ignition key turned off and the key taken out.2. Now without opening the doors, replug the battery and wait for 10 seconds.3. Turn on the headlights, turn on the engine and inspect the system’s functioning.