phase separation study of in-service thermally aged cast...
TRANSCRIPT
PHASE SEPARATION STUDY OF IN-SERVICE THERMALLY AGED CAST STAINLESS STEEL
ATOM PROBE TOMOGRAPHY
Martin Bjurman1,3, Mattias Thuvander2, Fang Liu2, Pål Efsing3,4. 1 Studsvik Nuclear AB
2 Chalmers University of Technology
3 Royal Institute of Technology (KTH)
4 Ringhals AB
• Thermal ageing of cast and welded austenitic stainless steels is an important issue in LTO-programs
• The cast component are generally large and replacements are costly.
• Variations in overall composition and solidification rates affects. • Ferrite content, size and morphology.
• Overall microstructure.
• Segregation and compositional variations within each phase.
• Aging mainly occurs in δ−ferrite where • Cr-rich α´- and Fe rich α-phase forms by spinodal decomposition.
• G-phase forms by nucleation at the α´ to α phase boundary.
Introduction
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 2
• In-service thermal aging of ferrite from CF8M was investigated by APT for spinodal decomposition and precipitation.
• Two specimens were analysed from ageing at 325°C and 291°C in both laser and voltage pulse modes.
• Limited work has previously been conducted using 3D-APT on in service aged material below 325°C for large production castings.
• This work is part of a base characterisation for various ongoing mechanical testing.
Work content and motivation
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 3
Materials investigated Component
Full power time ~70 000h ~22 000h
hot leg 325ºC 303ºC
Cold leg 291ºC 274ºC
∆T 34ºC 29ºC
Total Full Power time 92 000h
• Material: ASTM 351 CF8M • Ringhals 2 old steam generator (SG) elbows
• inlet (hot) • crossover (SG-outlet) to reactor coolant pump
Inlet Crossover
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 4
Unaged Aged tangetial Aged axial
Crossover 137 69 71
Hot 141 33 31
Charpy Impact test results in Joule (KCU) at 20ºC
Materials investigated Composition and microstructure
C Si Mn P S Cr Ni Mo Ti Cu Co N Ferrite content
Hot leg 0.037 1.03 0.77 0.022 0.008 20.0 10.6 2.09 0.004 0.17 0.040 0.044 20.1
Crossover 0.039 1.11 0.82 0.020 0.012 19.6 10.5 2.08 0.004 0.08 0.035 0.037 19.8
• Local Ferrite-content measured by Ferritescope varies 1.5-22.5% across the component.
Atom % Fe Cr Ni Mn Si Mo
Hot-leg Ferrite 63.1 26.4 5.57 0.82 2.00 2.05
Austenite 65.7 20.8 9.41 0.96 1.82 1.30 Crossover-leg Ferrite 62.9 26.5 5.69 0.87 1.91 2.11
Austenite 65.5 20.5 10.26 0.80 1.82 1.14
Table 4. Results from EDS-analysis of ferrite and austenite in as received material.
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 5
• Two solidification routes occur • Liquid→Liquid+δ→Liquid+δ+γ→δ+γ Generally SS- weld materials • pure δ-solidification Generally large CF8M-castings
• CF8M castings of both routes are found in the literature.
• Scheil-ThermoCalc Calphad modelling and simplified equations1 are used for verification.
• Time independent techniques assuming diffusion of species to be • infinite in the liquid phase, • equilibrium at the interface and • zero diffusion in the solid phase.
• The present castings are close to the limit between these routes
• Final annealing at 1050°C and quenching. • Quenching rates have previously been shown to affect the rate of spinodal decomposition • local ferrite content variations of 1.5 - 22.5 % are indications
• A possible contributor to the decomposition, especially of importance for the small decomposition of the crossover-leg, is decomposition that might have occurred during cooling of the original casting.
1 Suutala N. , Met. Trans. A, vol. 14A, 191–197, 1983
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 6
Manufacturing
• Sample extracted approximately 10 mm below outer surface.
• Limited Ferrite content => Sample lift out by Focused Ion Beam/ SEM using a FEI Versa 3D DualBeam.
Atom Probe Tomography – Sample lift out by FIB
85 mm
950 mm
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 7
Sample extraction (hot leg)
Results – APT radial density functions Spinodal Decomposition
0.95
1
1.05
1.1
1.15
1.2
1.25
1.3
1.35
1.4
1.45
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
Bulk
Nor
mal
ized
Conc
entr
atio
n
Radial distance (nm)
0.98
1
1.02
1.04
1.06
1.08
1.1
1.12
0 1 2 3 4 5 6 7 8 9 10
Bulk
Nor
mal
ized
Conc
entr
atio
n
Radial distance (nm)
Hot-leg
Crossover-leg
Cr
Ni
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 8
Wavelength 6.8 nm
Wavelength 4 nm
Decomposition amplitude
Atomic maps of projected volumes (20x20x5 nm³ slices)
hot-leg crossover-leg.
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 9
Chromium-concentration
Nickel
Manganese
Silicon
Limit Si Mn Cr Ni P Mo W V Cu Co
α Fe>72 1.10 0.18 12.9 3.66 0.02 1.10 0.01 0.03 0.02 0.05
α' Cr>30 1.98 0.57 42.0 4.09 0.04 2.13 0.01 0.11 0.01 0.04
G Ni+Mn+Si >20
11.0 4.28 16.5 20.5 0.21 2.16 0.03 0.05 0.18 0.06
Iso-concentration plot of hot-leg
Composition (at.%) of the different phases of the hot-leg, balance Fe.
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 10
The size of the box is 34×34×37 nm3.
α'-phase α-phase G-phase
Proximity Histogram of Hot leg G-phase
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
0
5
10
15
20
25
-10 -8 -6 -4 -2 0 2
Conc
entr
atio
n (a
t.%)
Distance from interface (nm)
Ni
Si
Mn
Cu
P
Conc
entr
atio
n (a
t%)
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 11
Increased levels of Cu and P in the G-phase
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
0 1 2 3 4 5Bulk
Nor
mal
ized
Conc
entr
atio
n
Radial distance (nm)
Hot-leg
Crossover-leg
Radial Density Functions – G-phase clustering
0.91
1.11.21.31.41.51.61.71.81.9
0 1 2 3 4 5
Bulk
Nor
mal
ized
Conc
entr
atio
n
Raidal distance (nm)
Hot-leg
Crossover-leg
Mn with respect to Ni as ref. point.
Si with respect to Ni as ref. point.
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 12
Si Mn Cr Ni Mo Fe 15.2 4.6 8.9 45.7 0.9 24.5
Average comp. (at.%) of clusters in the crossover-leg.
Cluster density of 5.6×1024 m-3 Cluster size 57 atoms
• In-service thermal aging of ferrite from CF8M was investigated by APT for spinodal decomposition and precipitation.
• Two specimens were analysed from hot- and crossover-legs in both laser and voltage pulse modes.
• Hot-leg aged at 325°C • Spinodal decomposition was significant with spinodal length of 6.4 nm and a Cr-concentration amplitude of
10.8 at %.
• G-phase was estimated to 3.9×1024 m-3 and diameter 3.2 nm for the hot-leg,
• Crossover-leg aged at 291°C • Limited spinodal decomposition with spinodal length of 4 nm and amplitude 8.1 at %
• G-phase precipitation with a cluster density of 5.6×1024 m-3 of approximately 57 atoms in each position, much less than expected from the hot-leg content.
• The reduction in fracture resistance previously measured in the crossover-leg is high compared to the weak spinodal decomposition measured by APT.
Conclusions
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 13
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 14
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 15
APT - Ferrite Composition
Si Mn Cr Ni P Mo W V Cu Co Hot 2.22 0.63 24.4 5.71 0.06 1.84 0.02 0.06 0.02 0.05
Crossover 2.10 0.62 23.9 5.80 0.05 2.20 0.001 0.06 0.03 0.03
Composition (at.%), balance Fe.
Local electrode atom probe, Imago LEAP 3000X HR.
• Sample in the shape of a needle with tip radius =10-100 nm
• Ultra-high vacuum (UHV), <10-10 torr
• Cooled sample 50 and 70 K (20-80 K)
• Standing DC voltage (V=3-15 kV)
• Short (ns) pulses at 200 kHz to achieve field evaporation • Voltage pulse (metals) to increase electrical field 15% (15-25%)
• Laser pulse (non-metals) to increase temperature 0.3 nJ or 523 nm (0.01-1.0 nJ)
• Analyzed volume typically 60x60x200 nm3
• Chemical analysis by counting atoms from TOF-MS
• Detection efficiency 37% with reflectron
APT - Equipment
17th International Conference on Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors 16