picture to come · negotiated sales for heavy equipment & industrial assets 2004 caterpillar...

Negotiated sales for heavy equipment & industrial assets

2004 Caterpillar 777D

Year 2004 Manufacturer CaterpillarModel 777DAsset Type Rock TruckSerial Number CAT0777DHAGC01365Usage 35,235 hrsComes with retarder, A/C, liner, auto lube, 27.00R49

rbauction.com/privatetreaty

Asset 3

Don’t miss out! Contact Scott Zeilstra to make an offer:+1.780.686.0725 [email protected]

PICTURE TO COME

COMPONENT

CHANGES

JHA CompletedNo Yes

MakeYes No Yes No

ST OT

Yes No

Rev: 1/25/2013

Work Date

Customer Unit No

SMU OutWork Order No Unit Number Shift

Day Shift Night Shift

SMU In

Technician Name Signature

Time UpTime DownSite ContactEquipment Location

Repair 1 Information

Model Serial Number

Customer Name


Wty or Redo

Complaint Correction

Repair 1 Details

Component - Work Type

Parts Ordered

Total

Repair HoursSegment

Complications:

Complaint

Repair 2 Details

Component - Work Type Correction

Emeco Supervisor Name

Complications:

Travel Allowance

The above work has been completed to my satisfaction

Customer ApprovalEmeco ApprovalSignature

Yes No Machine Released to Customer

Customer Name Signature

SERVICE REPORTS

JHA CompletedNo Yes

MakeYes No Yes No

ST OT

Yes No

Rev: 1/25/2013

Work Date

Customer Unit No

SMU OutWork Order No Unit Number Shift

Day Shift Night Shift

SMU In

Technician Name Signature

Time UpTime DownSite ContactEquipment Location


Model Serial Number

Customer Name


Wty or Redo

Complaint Correction

Repair 1 Details

Component - Work Type

Parts Ordered

Total

Repair HoursSegment

Complications:

Complaint

Repair 2 Details

Component - Work Type Correction

Emeco Supervisor Name

Complications:

Travel Allowance

The above work has been completed to my satisfaction

Customer ApprovalEmeco ApprovalSignature

Yes No Machine Released to Customer

Customer Name Signature

Verified by: J.Everett © EMECO International Issue Date Review Page No.

Initial: MAINTCLF002 – CAT 777BCD Dump Truck

500 Hour Service Sheet 1.0 Apr 2006 Apr 2007 Page 1 of 5

MAINTCLF002 CAT 777BCD DUMP TRUCK

500HR SERVICE Unit Number: SMU: Date:

SAMPLE Initial Engine Transmission Hydraulic / Brakes Steering Front hubs LH ( ) RH ( ) Differential Final Drives LH ( ) RH ( ) Cooling system (level 2 analysis) – aftercooler and engine REPLACE Engine oil Cap (91 L) Engine oil filters Cut 1 filter open Clean ( ) Metal ( ) Front brake cooling filters (hydraulic) Front Hub oil LH ( ) RH ( ) Cap (5 L each) Fuel filters Fuel system water separator element Primary air filters Transmission oil filter Transmission breather Hydraulic tank breather Hoist, torque Converter and Brake tank Breather Steering system oil filter Park brake release filter Front Axle breather Differential Breather CLEAN Hoist high pressure screens clean ( ) metal ( ) material ( ) Torque converter outlet screens clean ( ) metal ( ) Transmission magnetic screens clean ( ) metal ( ) material ( ) Batteries and terminals Engine breathers clean ( ) change ( ) Engine air Filter Pre-cleaner Assembly Differential breather Front hub breathers Transmission breather Air conditioner filter Air/hydraulic cylinder breather clean Walkways, handrails, cab – controls, screens, floors etc free of grease and oils CHECK Engine oil level Coolant charge level Drain water and sediment from fuel tank Drain moisture and sediment from air tank Transmission oil level Differential oil level Final drive oil levels Hoist, torque converter and brake oil tanks level Front wheel hub oil levels LH ( ) RH ( ) Steering oil level Fill fuel tank and record litres if applicable ( L)

MattB

Typewritten Text

rdc028

MattB

Typewritten Text

33874hrs

MattB

Typewritten Text

feb 8, 2014

MattB

Typewritten Text

mb

MattB

Typewritten Text

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

x

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

mb

MattB

Typewritten Text

MattB

Typewritten Text

mb




GREASE Fan hub and jockey pulley (hand gun only) Driveshaft splines and universal joints (hand gun only) Fill bulk grease tank

Ball Stud Inspection 1) Clean all steer cylinder and tie rod ends down. 2) Drive truck in straight line so as not to load up steering geometry. 3) Chock and tag vehicle 4) Bar all tie rod and steer cylinder points to locate any movement. 5) If movement found, set up dial indicator and measure amount of movement. 6) If movement is greater than 1 mm, remove cap and determine is wear is between ball stud and bearing race, or bearing race and housing. Record which area is worn 7) Ball stud wear limits: 0 to 1.02 mm - OK 1.02 to 1.27 mm - schedule for change out 1.27 mm and above - change out ball stud 8) Record measurement:

CHECK 1 2 3 4 Steering accumulator – using ground level engine shutdown switch stop engine then check for steering operation.

Visual check on duo cone leakage acc hub positions Report on any significant coolant usage (to indicate internal leakage) Check steering ball joint wear as per service manual, maximum wear in any ball joint is 1.02mm. Check all ball joint covers are in good condition

Check tie rod ends for movement Steering (cylinders, valve and joints) Air Conditioner – condition and operation Air Dryer operation, check for moisture in secondary air tank – note 2 air dryers fitted to unit (785C only)

Belts – inspection/adjust/replace Rock ejectors Induction system for leaks and clamps for tightness All hoses for general condition and chaffing Cooling system hoses for condition and clamps for tightness Brake cooling hoses for leaks, hardness and damage. Replace as required Fuel system for loose bolts and fittings Download VIMS, check operation and report overspeeds. Inspect hydraulic hoist cylinder hoses for damage, wear or deteriorated condition. Replace hoses as required.

Engine mounts Frame and body support pads. Clean and inspect for cracks

1 2 3 4 5 6 7 8

LEGEND FOR COLUMNS: 1 – Defect found and repaired 2 – Defect on machine, machine still OK 3 – OK 4 – Not applicable

MattB

Typewritten Text

ok

MattB

Typewritten Text

MattB

Typewritten Text

ok

MattB

Typewritten Text

ok

MattB

Typewritten Text

ok

MattB

Typewritten Text

ok

MattB

Typewritten Text

ok

MattB

Typewritten Text

ok

MattB

Typewritten Text

ok

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x




CHECK 1 2 3 4 ROPS/Cab and chassis attachment points for damage, cracks, corrosion or loose/missing bolts

Retarder lever free play Radiator for debris (wash if necessary) Cooling system pressure cap- clean inspect and replace as required Cooling system pressure relief valve - clean Engine shutdown system – test operation Exhaust system for leaks and clamps for tightness All points are receiving grease Inspect pre-start book and ensure all defects are repaired or documented Suspension cylinder heights (adjust if necessary): LHF LHR RHF RHR SPEC FRONT REAR

Steering accumulator nitrogen pressure: - See table for acceptable pressure. Use only correct procedure in workshop manual.

21 °C 300 psi 27 °C 306 psi 32 °C 312 psi 43 °C 324 psi Tyre pressures: Adjust cold pressure only Radial - 105 psi cold Bias Ply – 82 psi cold

Pos 1 Pos 2 Pos 3 Actual Adjusted Pos 4 Pos 5 Pos 6 Actual Adjusted Magnetic plug conditions*: RHF LHF RHR LHR

NOTE: Boxes A - F are to be initialled by person carrying out safety checks. Every person carrying out these checks must also sign off Safety Check Sheet before the end of each shift.

SAFETY CHECKS A B C D E F Service Brake Operation Stall Test Spec: 777BCD 1st Gear Stall Test - must hold at 1300 RPM

Emergency/secondary brake stall test Spec: 777BCD 1st Gear Stall Test - must hold at 1300 RPM

Park brake operation Spec: 777BCD 1st Gear Stall Test - must hold at 1300 RPM

Retarder operation Steering operation Emergency steering operation Seat belt – retainers and operation Seats – suspension adjustment/condition Horns – air and electric Wipers Mirrors Doors Windows

*LEGEND: OK – OK P – Paste HP – Heavy Paste

LF – Light Flakes

HF – Heavy Flakes (Return to Foreman)

LEGEND FOR COLUMNS: A – Machine is not safe – defect must be repaired D – Defect found and repaired B – Defect found – authorisation required before returning to work E – OK C – Defect found and recorded – machine safe to operate F – Not applicable

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x




SAFETY CHECKS A B C D E F Gauges Audible alarm and warning lights Body up reverse inhibitor Grab rails Steps Fire extinguishers – invert & shake to loosen powder & inspect date Fire suppression bottle charge Tyre condition Lights Reverse alarm Wheel nuts Pin retainers Cab condition Operation of emergency stop Accumulation of fuel, oil, grease etc that may cause a fire Tray condition Rock ejectors condition (bent?) Grease system operation Two way radio operation

Chassis Crack Inspection

Notes: - Inspect all coloured areas for cracks – clean as required

- All non repaired cracks to be marked a crack ends and dated using paint marker

Rear tail casting section

1 2 3

LEGEND FOR COLUMNS: 1 – Crack found and repaired 2 – Crack on machine, machine still OK 3 – No cracks found

Cross tube area (Check both sides)

1 2 3

1 2 3

Fuel tank and hydraulic mounts (Check both sides)

1 2 3

Hoist cylinder supports and cross tube (Check both sides)

Transition castings (777 & 785 only)

1 2 3

Pedestal castings

1 2 3

1 2 3

Front Strut Mounting Castings –check weld section and flanges

1 2 3

Engine (both sides) and cab mounts

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x

MattB

Typewritten Text

x




DEFECTS PARTS SHEET YES/NO

COMPLETED YES/NO

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

Comments:

CARRIED OUT BY: CHECKED & RECORDED BY:

Print Name: Print Name:

Signed: Signed:

Date: Date:

MattB

Typewritten Text

matthew biamonte

MattB

Typewritten Text

feb 8, 2014

WORK ORDER HISTORY

Maintenance History for Equipment ID: RDC028Start Date Meter Reading (Hrs)Job Number / Description

9-Oct-2017 WOC240944 - FRONT TIRE INSTALLATION 32,699.

20-Aug-2015 WOC258603 - SRV > 2000 HR 35,171CARRY OUT 2000HRS SERVICE AND REPAIRS AS REQUIREDCARRY OUY BRAKE CHECK AS REQUIRED

ENGINE HOURS:

DATE:

SERVICE CARRY OUT BY:

MAGNETIC PLUG REPORT

LHF/FD:RHF/FD:F/DIFF:LHR/FD:RHR/FD:R/DIFF:

ALL DEFECTS ENTERED INTO GP

1-Jul-2015 WOC257875 - 2016 R&M - JUL 1 TO JUN 30 35,016

1-Jul-2015 WOC258368 - TYR > FY2016 PREPAID TIRES 35,132

24-Jun-2015 WOC257697 - SRV > CHANGE DIFF & FINAL OIL 35,016CARRY OUT DIFF AND FINAL OIL CHANGE

9-Jun-2015 WOC257517 - SRV > 1750 HR 35,171CARRY OUT 1750HR SERVICE AND REPAIRS AS REQUIRED

2-Jun-2015 WOC257450 - FIRE SUPPRESSION PM 34,899.

15-May-2015 WOC257236 - SRV > 1500 HR 34,930CARRY OUT 1500HR SERVICE AND REPAIRS AS REQUIRED

8-Nov-2014 WOC222065 - PERFORM ENGINE VALVE SET 31,906.

30-Sep-2014 ECA1451 - CA > INSTALL PORTA THAW 34,595Install porta thaw.

24-Aug-2014 WOC254434 - BC > MOBE AND DEMOBE 34,594Coal avlley to Ft Mac

1-Jul-2014 WOC254479 - TYR > FY2015 PREPAID TIRES 34,594

1-Jul-2014 WOC254195 - 2015 R&M - JUL 1 TO JUN 30 34,594

Page 1 of 36Emeco Canada Limited GST Registration # 104545959RTweb www.emecogroup.com Printed on: 12-Jan-2016

Meter Reading (Hrs)Start Date Job Number / Description

Maintenance History Continued for Equipment ID: RDC028

30-Jun-2014 WOC250286 - FIRE SUPPRESSION PM 34,899.

16-May-2014 WOC253504 - BC > REPAIRS 34,591Customer Damages; Replace spill guard. Replace control Knobs . Replace dash and body films. Summit machine welded spill guard on.

7-Apr-2014 WOC253203 - BRAKE AND STEERING TEST 34,469.

4-Apr-2014 WOC232729 - BRAKE AND STEERING TEST 34,469.

18-Mar-2014 WOC252978 - SRV > 1250 HR 34,741CARRY OUT 1250HR SERVICE AND REPAIRS AS REQUIRED

15-Feb-2014 WOC251239 - SRV > 1000 HR 34,437CARRY OUT 1000HR SERVICE AND REPAIRS AS REQUIRED

1-Jan-2014 WOC246541 - 2014 R&M - JAN 1 TO DEC 31 33,403

17-Dec-2013 WOC245274 - B/C REPAIR CATWALK 33,403Cat walk and entry door damage INVMA5753

25-Nov-2013 WOC227831 - FIRE SUPPRESSION PM 33,402.

23-Nov-2013 WOC243022 - SRV > 500 HR 33,874CARRY OUT 500HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:




ALL DEFECTS ENTERED INTO GP.

12-Nov-2013 WOC243029 - BOOST MACHINE 32,916Cory Michner asked that we come and boost the machine.

19-Oct-2013 WOC240203 - SRV > 250 HR 32,916CARRY OUT 250HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





20-Sep-2013 WOC231385 - SRV > 2000 HR 32,480




CARRY OUT 2000HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013/09/12 -SL - 32470RON DUYVEWAARDTPERFORMING 2000HR. SERVICE AND REPAIRS.

2013/09/13 - SL - 36480RON DUYVEWAARDTPERFORMING 2000HR SERVICE.

2013/09/14 - SL - 34680RON DUYVEWAARDTCHANGE STEERING OIL AND FILTERS. FINISHED TAKING SAMPLES. REPLACE DIFF BREATHER.

21-Jun-2013 WOC231316 - INSTALL VISIONLINK GPS 32,160.

29-May-2013 WOC222068 - SRV > 1750 HR 32,260CARRY OUT 1750HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:

SERVICE CARRIED OUT BY:



ALL DEFECTS ENTERED INTO GP

25-May-2013 WOC199158 - FIRE SUPPRESSION PM 32,160

14-May-2013 WOC223044 - FRONT TIRE ROTATION 32,599CHANGE OUT FRT TIRES

5-May-2013 WOC212324 - 1000HR SERVICE 31,906





ENGINE HOURS:

DATE:





17-Apr-2013 WOC209930 - TIRE REPAIRS 31,649TIRE REPAIR SCOPE:CHANGE OUT REAR TIRES

7-Apr-2013 WOC204723 - 1250HR SERVICE 31,649CARRY OUT 1250HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013-04-30-GLADIATOR EQUIPTRAVEL TO CUSTOMER SITE, PICK UP PARTS, PERFORM 250 HR SERVICE ON UNIT, CHANGE TRANS HOSES

3-Apr-2013 WOC206469 - PERFORM ENGINE VALVE SET 31,906.

18-Mar-2013 WOC199722 - 1000HR SERVICE 31,419CARRY OUT 1000HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013-03-06-GLADIATOR EQUIPTRAVEL TO CUSTOMER SITE, SERVICE UNIT, CHANGE OIL, FILTERS, CHANGE FUEL, FILTER, TRANS FILTER AND GREASE AND CHECK UNIT, RETURN TO LEDUC SHOP




26-Feb-2013 WOC210881 - BRAKE AND STEERING TEST 32,261.

28-Jan-2013 WOC180923 - TIRE REPAIRS 30,902TIRE REPAIR SCOPE:Change out frt tires KAL TIRE C/V

27-Jan-2013 WOC177828 - 500HR SERVICE 30,575CARRY OUT 500HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





2013/04/30GLADIATORTRAVEL TO CUSTOMER SITE. PICK UP PARTS. RECEIVE ORIENTATION AND SAFETY COURSE. PERFORM 500 HOUR SERSVICE ON UNIT

2-Jan-2013 WOC175049 - JAN 2 - DEC 31 2013 R&M WO 29,993




*************************************************************************************************************************************************NEW FORMAT TO BE USED TO TRANSFER REPAIR NOTES:

DATE (YYYY-MM-DD) - COMPONENT - Work TypeMechanic Name

-NOTE DETAIL A-NOTE DETAIL B-NOTE DETAIL C

EXAMPLE:

2012-07-23 - ENGINE - Inspect for LeaksEd. S.

Removed panels and check for coolant and oil leaks on machine. No leaks. Check oil level, coolantlevel and hydraulic levels, ok. There is no leak from engine. Start Unit run fine, let run for about 45min. No leaks.

************************************************************************************************************************************************

2013-01-05MATTHEW BIAMONTEREPLACE PARK BRAKE PUMP, FOUND ALL PIECES OF BROKEN GEAR, DID NOT GET RUNNING DROVEHOME

2013-01-07TREVOR VOLPATTICHANGE OUT PARK BRAKE FILTER, CUT OPEN TO INSPECT STILL SOME SMALL FLAKES, WILL CHANGEONCE MORE IN A SHIFT OR TWO

2013-01-16SCOTT MCLENNANT/S AND REPAIR TRANSMISSION COOLER LEAK, REMOVE AND REPLACE LHS HOIST CYL LIN, ESCORTODIE MECHANICAL TO UNIT FOR FIRE SUPPRESSION RE-CERT

2013-01-19SCOTT MCLENNANTRAVEL TO UNIT, PERFORM WEEKLY INSPECTION

2013-03-29-RON DUYVEWAARDTINVALID SPEED SENSOR DATA, CLEAN SENSOR AND HARNESS, TEST DROVE UNIT, WARNING GONE,REPAIRED LEFT HAZARD LAMP, CHECK TILT STEERING COLUMN, ORDERED PARTS

2013-04-15-CHRIS ROGERSONTRACK THE MACHINE DOWN ONLY TO FIND OUT THERE WAS A WRONG HOSE, ORDER NEW HOSE

2013-04-20-GLADIATOR EQUIPTRAVEL TO CUSTOMER SITE, MOVE UNIT, CHECK PADS, CLEAN PADS OFF, REPLACE 2 PADS,RECHECK AND PUT BACK INTO SERVICE

2013-04-30-GLADIATOR EQUIPPICK UP PARTS AT EMECO, TRAVEL TO CUSTOMER SITE, REPLACE FRONT AXLE BRAKE PADS, REARCALIPER ON BOTH SIDES, CUT PAD AND REINSTALL NEW PADS, DISASSEMBLE STEERING COLUMN,REPLACE BUSHINGS, RETURN TO LEDUC SHOP

2013-05-03-GLADIATOR EQUIPTRAVEL TO CUSTOMER SITE, CHECK STEERING COLUMN, REPAIR WIRING ON BOTH LEFT AND RIGHTFRONT PARK LIGHTS, TEST OK, RETURN TO LEDUC SHOP

2013/08/07 - TATREVOR VOLPATTIREPLACE OPERATOR TO MACHINE BOARDING DEVICE (LADDER)ATCO54 HRS->8552ATCO77 HRS->10756

2013/08/08 - TA/ELTREVOR VOLPATTICONFIRM NO SHIFT ISSUE, HOOK UP ET AND CHECK FAULT CODES, TROUBLESHOOT ISSUE, FOUND




ENGINE SPEED SENSOR DIRTY - REMOVED SENSOR AND CLEANED/ADJUSTED TO SPECS, TEST UNIT

2013/06/01GLADIATORTRAVEL TO CUSTOMER WITE. REAPLCE PARK LIGHT - STEERING COLUMN AND ENGINE DIPSTICK.RETURN TO LEDUC SHOP

2013/08/24 - OT - 32430MATTHEW BIAMONTEINSTALL COMPLETE 321 SETUPCOULD NOT GET LAPTOP TO CONNECT WITH CAT COMM ADAPTER. COULD NOT FINISHREGISTRATION

2013/09/13 - TR - 34680RON DUYVEWAARDTREMOVED HOUSING TO REMOVE BROKEN BOLTS. INSTALLED HOUSING WITH NEW BOLTS.

2013/09/14 - 34680RON DUYVEWAARDTREPLACE FRONT BRAKE PADS. TRYING TP REPLACE STEERING CYLINDER. NEED TOOLING. REPLACEHYD. AND TRANS. TANK DRAIN PLUGS. REPLACED MIRROR BRACE. REPLACED O-RING AT BRAKECOOLING MANIFOLD. ORDERED PARTS.

2013/09/16 - 32480RON DUYVEWAARDTREPLACE LEFT STEERING CYLINDER.

2013/09/17 - 32480RON DUYVEWAARDTREMOVE LEFT FRONT HUB FOR BEARING AND SEAL REPLACEMENT.

2013/09/18 - FN - OT - 32480RON DUYVEWAARDTREPLACE LEFT FRONT WHEEL BEARINGS AND SEAL. REPLACE RIGHT FRONT HUB MAG PLUG. REPLACEFINAL DRIVE AND DIFF PLUG GASKETS. REPLACE LEFT REAR MUDFLAP. REPLACE COMPANIONSEATBELT.

2013/09/18 - CS - 32480RON DUYVEWAARDTREPLACE 3 COOLANT SHUTOFF VALVES

2013/09/19 - 32480RON DUYVEWAARDTRESEAL TRANS COOLER BY-PASS PIPE. ASSIST KAL TIRE TO INSTALL LF TIRE. RETURN PRECIOUSJACK BACK TO MR.ALFIE.

2013/09/13 TA-SS-32511TREVOR VREMOVE RH STEERING CYL AND INSTALL NEW ONE. TALK TO OPERATOR, UNIT NEEDS A NEW LHSBOX LIGHT BOX

18-Dec-2012 WOC172886 - BI-WEEKLY DEC 18 - JAN 01, 13 29,728BI - WEEKLY DEC 19 - JAN 01, As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC13

16-Dec-2012 WOC197457 - FIRE SUPPRESSION PM 30,839PERFORM 1200HR FIRE SUPRESSION INSPECTION

COMPLETED BY ODIE MECHANICAL

15-Dec-2012 WOC169749 - 250HR SERVICE 30,252





ENGINE HOURS:

DATE:





2013-01-14TREVOR VOLPATTISTART 250 HR SERVICE, CHANGE COOLANT

2013-01-15TREVOR VOLPATTIFINISH OFF 250 HR SERVICE

4-Dec-2012 WOC169956 - BI-WEEKLY DEC 05 - DEC 18, 12 29,728




BI- WEEKLY DEC 05 - DEC 18, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2

DEC 4/12 RYAN ELLIS

PERFORM CYLINDER CUTOUT TEST WAS UNABLE TO COMPLETE TEST IT KEPT ABORTING, CUT OPENENGINE OIL FILTER AND FOUND NOTHING IN IT, NOT POSITIVE THAT VIBRATION COMPLAINT ISWORTH LOOKING INTO FURTHER, NEED TO PERFORM CYLINDER CUTOUT TEST AND GET RESULTS,EXHAUST LEAKS AT CROSSOVER PIPE ON MANIFOLDS

DEC 5/12 MATTHEW BIAMONTE

INSPECT EXHAUST LEAK, ORDER PARTS


REPAIR LEAKING ORING ON TRANS COOLER, INSTALL NEW HOSE


INSPECT FOR PARK BRAKE STUCK ON COMPLAINT, FOUND PARK BRAKE PUMP NO GOOD, NO FLOW,INSPECT FOR ENGINE NOISE, DID CYL CUT OUT FOUND NUMBER 2 CYL NO GOOD, INSPECT VALVETRAIN, EVERYTHING LOOKED GOOD


ORDER PARTS FOR ENGINE

DEC 12/12 - RYAN ELLIS

TRAVEL TO SITE, R&I TORQUE AND PARK BRAKE PUMP, CLEAN OUT TUBE FROM DEBRIS, CHECKSCREEN IN TANK FOR PARTICLES AND CLEANED, TOPPED UP HYDRAULIC LEVEL, CHANGED INJECTOR#2 TORQUED MOUNTING BOLT TO 52 LBS, FOUND BROKEN VALVE BRIDGE #2 EXHAUST, ROBBEDFROM A FAILED ENGINE AT THE MINE, INSTALLED ROCKER SHAFT AND TORQUED TO 180LBS, SETINJECTOR TRIM CODE, COMPLETED VALVE SET, SET TO CAT SPECS, START MACHINE AND RUN UP TOCHECK FOR LEAKS, WAS OK


START TRUCK, RUN UP TO TEMP AND CHECK OVER, CHECK ALL LEVELS, RELEASE TO MINE, GETHOURS ON ALL EQUIPMENT, MEETING WITH MARK


CROSSOVER PIPE LEAKING BETWEEN THE MANIFOLDS, ATTEMPTED TO CHANGE OUT, BOLTS ARESEIZED AND DIDN'T WANT TO DISABLE THE TRUCK, ORDERED PROPER STAINLESS STEEL BOLTS,INSPECT ALL EQUIPMENT ON SITE FOR PROPER OPERATION

DEC 17/12 - RON DUYVEWAARDT

MORNING CHECK

21-Nov-2012 WOC167063 - BI-WEEKLY NOV 21 - DEC 04, 12 29,503BI-WEEKLY NOV 21 - DEC 04 - 2As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC012

NOV 24/12 LUCAS ANDRIUK

FOUND A HOSE LEAKING, WENT AND BUILT HOSE, INSTALLED IT, LEAK IS FIXED, HAD A COMLAINT THAT STRUTS WERE LOW, WENT AND CHARGED UP STRUTS

NOV 28/12 LUCAS ANDRIUK

RDC028 29728 HRS WO# 167063 1 HRXHC063 10930 HRS WO#167583 .5 HRRDC063 2958 HRS WO# 167137 1 HRATC043 12908 HRS WO# 166866 .5 HRRDC065 3029 HRS WO# 167140 1 HR

6-Nov-2012 WOC163762 - BI-WEEKLY NOV 07 - NOV 20, 12 29,230




BI-WEEKLY NOV 07 - NOV 20, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC

NOV 13/12 CHRIS RODGERSON

DAILY INSPECTION

NOV 28/12 MATTHEW BIAMONTE

START 2000 HR SERVICE, PULL SOS SAMPLES, INSTALL SWITCH FOR BIRM LIGHT AND BACK UPLIGHT

23-Oct-2012 WOC160711 - BI-WEEKLY OCT 24 - NOV 06, 12 29,169




BI-WEEKLY OCT 24 - NOV 06, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC

OCT 24/12-LUCAS ANDRIUK

ARRIVED AT 123 DRY WAS TOLD THAT MACHINES ALTERNATOR HAS FAILED AND THAT COAL VALLEYMECHANIC HAS LEFT NEW ALTERNATOR WITH MACHINE, DROVE TO MACHINE INSTALLED NEWALTERNATOR, STARTED MACHINE AND NO PROBLEMS PERSISTED, CALLED MACHINE UP, GOTCALLED BACK TO MACHINE WITH SAME COMPLAINT, DROVE BACK TO MACHINE, BOOSTED MACHINEAND TESTED ALTERNATOR , FOUND NEW ALTERNATOR WAS NOT PUTTING OUT SUFFICIENTVOLTAGE WHEN REVED UP, ORDERED A NEW OEM ALTERNATOR AND SEPENTINE BELT, CLEANED ALLCONNECTIONS AND TESTED WIRING FOR FAULTS NOTHING FOUND

OCT 25/12- LUCAS ANDRIUK

DROVE TO MACHINE REMOVED FAULTY REBUILT ALTERNATOR FROM COAL VALLEY, INSTALLED NEWALTERNATOR NEW ALTERNATOR HAS AN EXTRA TERMINAL LABELED I CONSULTED MARK AND WASTOLD TO INSTALL AND SEE IF IT WORKS, HAD COAL VALLEY MECH BOOST MACHINE AND CHARGEBATTEIES FOR APPROX 30 MINS STARTED MACHINE, RECORDED VOLTAGE READING FROMALTERNATOR IS WORKING PERFECTLY AND NO DRAINAGE ON BATTEIES CAUSING A STALL, NOTICEDTHAT HEATER FAN MOTOR NO LONGER WORKED T/S AND FOUND CORRECT VOLTAGE AT SWITCHRESISTOR AND MOTOR CONNECTION CONSULTED WITH COAL VALLEY 777'S TO FIND THAT THEYARE C SERIES AND NOT D SERIES LIKE RDC028 AND THEY USE A COMPLETELY DIFFERENT MOTORORDERED A NEW MOROT VIA EMECO PARTS DEPT SUPPOSED TO BE READY FOR PICK UP IN AM

OCT 26/12- LUCAS ANDRUIK

DROVE TO MACHINE INSTALLED NEW HEATER MOTOR, BROKE ONE OF THE FAN WHEELS ONREINSTALLATION , AIRFLOW IN CAB IS STLL SUFFICIENT TO HEAT CAB ADEQUATELY , ORDEREDNEW WHEEL AND WILL INSTALL WHEN MACHIEN IS IN SHOP FOR PM MEASURED CANVAS FORWINTER FRONT WIRED CANVAS TO FRONT GRILL SPRAY PAINTED COAL VALLEY UNIT # ON CANVASCLEANED UP TOOLING AND WORK AREA

OCT 28/12- LUCASH ANDRUIK

DROVE TO MACHINE TO PERFORM INSPECTION WAS NOTIFIED BY COAL VALLEY MECHANIC THATMAHCINE WAS DOWN FOR A BENT ROCK EJECTOR REMOVED BENT ROCK EJECTOR AND ORDERED ANEW ROCK EJECTOR AND ASSOCIATED PARTS FROM FORT MAC PARTS DEPT, WAS CALLED BACK DUETO COMPLAINT OF LHS REAR STRUT SQUATTING TOO MUCH WITH A LOAD ON DROVE TO PIT 29 ANDLOOKED FOR EMECO'S NITROGEN CHARGING KIT BUT IT WAS NO WHERE TO BE FOUND, DROVEBACK TO MERCOAL PIT , CALLED SHOP FOREMAN AND OK ED WITH HIM TO CHARGE STRUT AT THESHOP FOLLOWED BACK TO THE SHOP TO CHARGE THE STRUT, CHARGED THE STRUT BUT RAN OUTOF TIME TO SEE IF IT WOULD HOLD PRESSURE UNDER A LOAD ADVISED OPERATOR TO KEEP AN EYEON IT AND LET ME KNOW WHAT HAPPENS , WILL INSPECT MACHINE IN AM TO SEE IF STRUT HOLDSPRESSURE OR NOT

OCT 29/12 LUCAS

DROVE TO 123 MAINTENANCE DRY AND INFORMED FOREMAN BRUCE OF WHAT I WAS DOING TORDC028 , DROVE TO MAIN SHOP WHERE MACHINE WAS PARTKED, REMOVED DIPSTICK TUBE THISTOOK SOME TIME AND WAS QUITE DIFFICULT DUE TO LOCATION OF DIPSTICK AND SIZE SHAPE OFDIPSTICK, COULDN'T FIND THE REMAINING PIECE OF THE BROKEN DIPSTICK PUSHED A FISH TAPETHROUGH AND NOTHING CAME OUT REINSTALLED TUBE AGAIN THIS TOOK SOME TIME AND WASDIFFICULT TO DO, INSTALLED NEW GASKET ON MOUNTING FLANGE INSTALLED NEW DIPSTICKCHECKED OIL LEVEL LEVEL WAS GOOD, STARTED MACHINE AND WARMED IT UP FOR OPERATORCALLED DISPATCH AND LET THEM KNOW MACHINE IS UP

OCT 30/12-LUCAS

DAILY INSPECTION

OCT 31/12 LUCAS

DAILY INSPECTIONS

OCT 31/12- LUCAS

DROVE TO MACHINE , REPLACED DAMAGED STEP LADDERS WITH NEW PARTS, CLEANED UP WORKAREA AND TOOLING

NOV 2/12/ LUCAS

DAILY INSPECTIONS

NOV 4/12- LUCAS




DAILY INSPECTIONS

NOV 3/12 LUCAS

INSTALLED NEW ROCK EJECTORS ON LHS OF MACHINE, NOTICED LHS REAR STRUT WAS LOWAGAIN TOLD OPERATOR TO WATCH IT WHEN HE WAS LOADED, OPERATOR CAME BY LATER WITH ALOAD AND ASKED ME TO CHECK OUT THE STRUT, STRUT WAS FULLY COMPRESSED TOLD OPERATORTO DUMP HIS LOAD AND MEET ME AT THE SHOP TO RECHARGE THE STRUT, DROVE TO THE SHOPAND MET OPERATOR AT THE MACHINE, FOUND PAYLOAD SENSOR/CHARGING VALVE TO HAVE COMELOOSE OFF OF STRUT, REMOVED VALVE AND CLEANED IT UP REPLACED A DAMAGED O-RING,REINSTALLED VALVE SENSOR PUT BLUE LOCTITE ON THE MOUNTING BOLTS TO PERVENT IT FROMCOMING LOOSE AGAIN , CHRGED STRUT, CLEANED UP WORK AREA AND TOOLING

NOV 5/12 LUCAS

DAILY INSPECTIONS

NOV 6/12- LUCAS

ASKED COAL VALLEY FIELD SUPERVISOR BRUCE IF THERE WAS ANY EXTERNAL MAINTENACE WORKTO BE DONE FOR COAL VALLEY WAS TOLD THERE WAS NOTHING DROVE BACK TO PIT 29 AND WASON STANDBY IN CASE ANY EMECO MACHINES WENT DOWN, WASHED TRUCK WROTE CROSSOVERNOTES FOR CHRIS ORGANIZED ANY PARTS NEEDED FOR UPCOMING JOBS

NOV 6/12 LUCAS

DAILY INSPECTIONS

13-Oct-2012 WOC155425 - 2000HR SERVICE 29,807CARRY OUT 2000HR SERVICE AND REPAIRS AS REQUIRED

ENGINE HOURS:

DATE:





NOV 29/12 RYAN ELLIS

GO TO SHOP AND CLEAR BAY SPACE, START MACHINE AND WARM UP, BRING INTO SHOP, CHANGED TRANS OIL AND FILTERS, CHANGED HYDRAULIC OIL AND FILTERS, CHANGED STEERING OIL AND FILTERS, CHANGED ENGINE OIL AND FILTERS, CHANGED FRONT HUB OIL AND REPAIRED DRAIN PLUG THREADS AND REPLACED PLUG, CHANGED DIFFERENTIAL OIL AND FINAL DRIVES, WELDER REPAIRED STEPS AND BODY PIN, CHECK MAGNETIC SCREENS

9-Oct-2012 WOC157254 - BI-WEEKLY OCT 10 - OCT 23, 12 28,904




BI-WEEKLY OCT 10 - OCT 23, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC

OCT 11/12- CHRIS RODGERSON

INSTALL THE LEFT REAR STRUT BUT COULD NOT FINISH BECAUSE SOME PARTS ARE BACK ORDERED


INSTALL THE VALING FOR THE LEFT REAR STRUT AND ORDER CHARGE VALVES FOR THE STRUT


CHARGE THE REAR STRUT AND DIAGNOSE AND REPAIR A ELECTRICAL PROBLEM WITH THESTARTING SYSTEM , REPLACED THE MASTER SWITCH WITH ONE THAT I GOT FROM THE CV SHOP

OCT 19/12- MATT BIAMONTE

REPAIR DAMAGED WIRING GOOD

25-Sep-2012 WOC154857 - BI-WEEKLY SEPT 26 - OCT 09, 12 29,005BI-WEEKLY SEPT 26 - OCT 09, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2

SEPT 29/12

Repair ladder/grille light, tighten diff drain plug, repair antenna wiring.

SEPT 29/12- RENE KREMER

REPIR BURNT OUT LADDER /GRILLE LIGHT BULB TIGHTEN LOOSE DRAIN PLUG ON REAR DIFF, REPAIR ANTENNA WIRING TO TWO WAY RADIO EMAIL PICSoCT 2/12- CHRIS RODGERSON

MORNING CHECKS

OCT 2/12- LUCAS

DROVE TO MACHINE DID MORNING INSPECTION AND RECORDED UNIT HOURS


MORNING CHECKS

OCT 3/12- LUCAS

INSPECTED MACHINE RECORDED HOURS

OCT 5/12- LUCAS

INSPECTED MACHINE , RECORDED HOURS, REMOVED RHS FRONT WHEEL MAGNETIC PLUG, NO FILLINGS , CUTTINGS FOUND

OCT 8/12LUCASWas told that machine had broken down in Yellowhead pitDrove to machine, found LHS rear strut retaining bolt had sheared off allowing upper pin to walk out and strut to fall outStrut had valve sheared off and the lower pin retaining bolt was missing as well

Went through SIS and wrote down necessary parts for repairDrove to a spot with cell phone service and called in parts order to Fort Mac

Informed pit foreman and maintenance foreman that the machine will be down until parts arrive

Tagged machine out of service

11-Sep-2012 WOC152805 - BI-WEEKLY SEPT 13 - SEPT 26,12 28,653




BI-WEEKLY SEPT 13 - SEPT 26,1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2

SEPT 12/12- ED SZYBUNKA

WENT BACK TO UNIT AND CHECK RETARDER AIR PRESSURE AS PER MARK, FOUND OIL IN LINES, AIRPRESSURE LOW. HOOKED UP LAPTOP HAD ARC VALVE STUCK OPEN REMOVED AND CLEANED ANDINSTALLED, AIR PRESSURE NOW 79 PSI OK. PREFORMED BRAKE TESTS ALL WORK FINE AND INSPEC. RESEALED AIR LEAK AT BRAKE VALVE AND TESTED NO LEAKS. CALLED FOR OPERATOR ANDRUN UNIT FOR ABOUT 3 HRS ALL WORKED FINE RELEASED TO CUSTOMER AND TALKED TO MARK ONWHAT WAS FOUND.

SEPT 11/12- ED SZYBUNKAINSTALL GPS AND INSTALL LEFT HAN PLATFORM BACK UP LIGHT


PICK UP PARTS AT SEA CAN AND TRAVEL TO UNIT AND PREFORM 500 SERVICE, TAKE OILSAMPLES, CHANGE OIL, CHANGE ALL FILTERS AND BREATHERS, REPAIR OIL LEAK AT RIGHT DRIVER.


REPLACE STEERING TILT AND PAW KIT AND TRAVEL BACK TO SHOPSEPT 20/12 CHRIS RODGERSON, COMPLETE A 1000 HR PM AND TIRE REPORT THE AIR

DRIER DESECANT WAS BACK ORDERED SO CHOLD NOT REPLACE

SEPT 16/12

sept

29-Aug-2012 WOC150598 - BI-WEEKLY AUG 29 - SEPT 12, 12 28,515BI-WEEKLY AUG 29 - SEPT 12, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2

SEPT 10/12- CHRIS RODGERSON

Brakes not holding at 1200 rpm

We tested the brakes and found that the brake where holding at 1200 RPM but started to brake loose at 1250 RPM which is within finningsspecs but the operator felt unsafe.

We tested all of the pressures and all were within specs, the filters and sceens were clean and the brake linings were within spec but close to maximum wear we also found that the linings were badly warped.

23-Aug-2012 WOC177550 - FIRE SUPRESSION RECERT 30,143PERFORM 1200HR FIRE SUPRESSION INSPECTION

17-Aug-2012 WOC149015 - GPS UNIT 28,512.

15-Aug-2012 WOC148704 - BI-WEEKLY AUG 15 - AUG 28, 12 28,512




BI-WEEKLY AUG 15 - AUG 28, 12

AUG 15/12- MATTHEW BIAMONTE

Order parts, Pick up parts, drive to mine, repair oil leak, drive back to hotel in edson

repair oil leak from transmission coolerattempt to charge front struts, would not charge will try tomorrow with coal valley equipment


pick parts up at edson transportcharge front struts with oil and nitrogenrepair leak off hyd control valvegot stands lined up and start setting u

AUG 19/12- SCOTT MYLES

DRAIN AC SYSTEM, CHANGE DRYER, RENT A/C SYSTEMp to remove fronEWBIAMONTESDF\ASDFASF\\AFDASFASDFASD

AUG 22/12- CHRIS RODGERSON

FOUND THAT THE LEFT FRONT BRAKE PAD WAS MISSING AND THAT THE RETAINING BOLT WASBACKED OUT SO WE INSTALLED A NEW PAD AND LOCKITED ALL OF THE RETAINING BOLTS ON ALLOF THE CALIPERS, TORQUED THE RETAINING BOLTS TO 38FT LBS ANDMARKED THEM WITH A BLUEPAINT PEN

ADFASDF

ASDFAS

AUG 19/12- SCOTT MYLES

DRAIN AC SYSTEM, CHANGE DRYER, RENT A/C SYSTEM

14-Aug-2012 WOC148422 - REPLACE FRONT BRAKES 28,512Left inner tierod loose.Center dash panel brokenFront brakes worn out / brake rotors worn.Replaced front pads and rotors as they were passed spec.

31-Jul-2012 WOC146708 - BI-WEEKLY AUG 01- AUG 14, 12 27,830BI-WEEKLY AUG 01- AUG 14, 12

AUG 2/12- CHRIS RODGERSON

Completed a in sheet inspection and a tire report and found some minor leaks and small repairs, The truck has no physical damage and appears to be in good

condition.


Repair leak on transmission oil cooler.

17-Jul-2012 WOC144472 - BI-WEEKLY JULY 18 - 31, 2012 27,830BI-WEEKLY JULY 18 - 31, 2012

4-Jul-2012 WOC142401 - BI WEEKLY WORK ORDER 27,456q04/07/12 to 17/07/12

JULY 6/12 - GORDON W (FINNING)

REMOVED REAR BRAKE BOOSTER, CLEANED AND DISASSEMBLED IN PREPARATION FOR RESEAL

JULY 6/12 - KEITH O

RUN PARTS TO BUS STATION

20-Jun-2012 WOC140160 - BI-WEEKLY WORK ORDER 27,199




Bi-Weekly Work Order 20-06-12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC to 03-07-12

19-Jun-2012 WOC140054 - CHECK PARK BRAKE UPDATE 27,199CHECK FOR CORRECT VALVE ON PARK BRAKE UPDATE

11-Jun-2012 WOC138605 - CHANGE TRANS PUMPS 27,199R&R pump - Cardinal river- Tercon.

JUNE 11/12- CHRIS

CHANGE TRANS PUMP

11-Jun-2012 CME183 - R&R TRANSMISSION 27,199R&R TRANSMISSION ***EARLY FAILURE***REMOVE AND INSTALL TRANSMISSION AT CUSTOMER'S SITE(CARDINAL RIVER MINE, HINTON)

7-Jun-2012 WOC138270 - CHANGE OUT TRANS 27,199Trans R&R

5-Jun-2012 WOC137901 - BI-WEEKLY JUN 06 - JUN 20, 12 27,457BI-WEEKLY JUN 06 - JUN 20, 12JUNE/13, 12- CHRIS RODGERSON

CHIPMUD AWAY FROM THE TRANSMISSION AND PUMP IT TOOK 2 HOURS THEN REPLACED THE TRANSMISSION AND PUMP BECAUSE THERE WAS METAL STARTING TO ACCUMULATE IN THE FILTERS AND SCREENS. THE OIL SAMPLE CAME BACK NORMAL I COULD NOT CHANGE THE COOLER DUE TO THE AMOUNT OF MUD ON THE ENGINE AND COULD NOT GET IT STEAMED IN TIME

22-May-2012 WOC135041 - BI-WEEKLY MAY 23 - JUNE 05, 12 26,570BI-WEEKLY MAY 23 - JUNE 05, 12

8-May-2012 WOC133783 - BI-WEEKLY MAY 09 - MAY 22, 12 26,570BI-WEEKLY MAY 09 - MAY 22, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CCCustomer performed 5oo hr service on May 15th @26909 hrs

MAY 15/12-

500 HR PM

24-Apr-2012 WOC132284 - BI-WEEKLY APR 25 - MAY 08, 12 26,249BI-WEEKLY APR 25 - MAY 08, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC

10-Apr-2012 WOC131081 - BI-WEEKLY APR 11 - APR 24, 12 26,249BI-WEEKLY APR 11 - APR 24, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC

APR.19.2012-LARRY N CAB DETAILS REMOVE GARBAGE,SWEEP FLOOR, WIPE DOWN DASH AND WINDOW,SEAT COVER

29-Mar-2012 WOC129261 - BI-WEEKLY MAR 28, - APR 10, 12 26,249BI-WEEKLY MAR 28, - APR 10, 1As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC2

14-Mar-2012 WOC126561 - BI-WEEKLY MAR 14 - MAR 27, 12 26,249BI-WEEKLY MAR 14 - MAR 27, 12As per discussion with Chris McNeil & Julio, these won is to be closed.30/4/13 CC

MAR 14, 201 2- CARL LCOLT STARTHAD TO HAUL PRO HEAT TO IT TO GET IT GOING.

29-Feb-2012 WOC124323 - C/O TIRES 26,240C/O Tires

27-Feb-2012 WOC123811 - BI-WEEKLY FEB 29 - MAR 13, 12 26,258




BI-WEEKLY FEB 29 - MAR 13, 12

MAR 2, 2012 - JERAMEY SSTEPS BROKENINSTALLED NEW BRACKET FOR RHS STEP. BROKE A BOLTS DURING INSTALL. HAD WEISER TRYAND WELD A NUT ON BOLT BUT BOLT WOULS NOT COME OUT. NUT KEPT SHEARING OFF. TRIEDMULTIPLE TIMES WITH NO SUCCESS. FABRICATED A NEW MTG BLOCK FOR STEP BRACKET, HAD TOCUT, DRILL AND TAP STEEL.

MAR 2, 2012 - MEL KENYON (GLADIATOR)INSTALL FRONT WHEEL REAR BRAKE PADS. TORQUE RH FRONT CALIPER BOLTS. BLEED BRAKES.PAT OLD PADS IN STEEL PIN.

MAR 3, 2012 - LARRY JREPLACE FRONT BRAK PADS AND BLEED BRAKES. FINISH INSTALLING GPS AND REPAIR LIGHTS.DO OUT SHEET, REPAIRS FTILL NEEDED, CHECKED THAT PARTS WERE ORDERED. TOP UP FLUIDS.

MAR 3, 2012 - BRUCE GREENWOOD (TUNDRA)GPS INSTALLCHANGE SIR/HYDRAULIC SWITCH AND IT BROKE, HOTWIRE IN ORDER TO BRING UNIT TO SHOP ANDORDER NEW ONE. INSTALL ANTENNA, INSTALL PARK SWITCH AND WIRE IN. WIRE IN POWERSUPPLY.

MAR 3, 2012- LOUIS DEBLOIS.FILL HOT BOX WITH DIESEL. MOVE TO UNIT, HOOK UP DUCTING TO 777D. (WARM ENGINE UPO)CLEAN BAY FROM LAST JOB. STARTED REPLACING FRONT BRAKE PADS.

MAR 3, 2012 - STAN STEWARTREMOVE RIGHT FRONT PADS ON CALIPERS. FREE PINS, REINSTALL BOLTS NOT TORQUED.

MAR 3, 2012 - MIKE LREPAIR STEPCUT BLOCK IFF AND WELD NEW BLOCK ON AND BOLT STEP.

MAR 3, 2012 - TRAVIS GMOVE UNIT INTO SHOP.HELP UNIT INTO SHOP AND PREP FOR REPAIRS.

MAR 4, 2012 - AARON CCHARGE FRONT AND BACK STRUTS.

MAR 4, 2012 - JERAMEY SFAILED XSMN INPUT SHAFT SEALASSISTED MECHANICS IN PROCEDURE AND INSTALLATION OF TRANNY SEAL.

MAR 4, 2012 - STAN STEWARTINSTALL TRANS INPUT SEAL TORQUE ALL BOLTS. RESET ROCK INJECTOR AND INSTALL MISSINGCOTTER PIN. CHECK ON PARTS ORDER.

MAR 4, 2012 - TRAVIS GTRANSMISSION INPUT SHAFT SEALK LEAKING.REMOVE COVER AND INPUT SHAFT. REMOVE OLD SEAL AND REPLACE WITH NEW ONE. INSTALLAND TORQUE YOKE, SHAFT. INSTALL COVER.

MAR 5, 2012 - AARON CREPAIRS, OUTSHEET, TIRE REPORT, ORDERS AND PICK UP HOSE AT FINNING.

MAR 5, 2012 - LOUIS DEBLOIS (TUNDRA)CHARGE RH REAR SUSPENSION (GOOD). FOUND WHY BRAKE LIGHT STAYS ON (REPAIRED).

MAR 6, 2012 - STAN STEWARTCHANGE OIL LINE RIGHT SIDE OIL PAN NOEW O-RINGS. WAITING FOR HYD LINE ON SAME SIDE.

MAR 6, 2012 - JERAMEY SOUTSHEET INSPECTION. TAKE PICS AS PART OF OUTSHEET INSPECTION.

26-Feb-2012 WOC123617 - B/S TEST 26,240PERFORM BRAKE AND STEERING TEST

25-Feb-2012 WOC123565 - 1200 HR F/S RECERT 26,240




PERFORM 1200 HR F/S RECERTIFICATION

FEB 25, 2012 - LAWRENECE SLACKROUND UP WELD ON THREAD O LETS AND REST OF HARDWARE. BUFF OFF FRAME, ISNTALLEDTHREADS O LETS FOR FIRE EYES.

FEB 27, 2012 - LAWRENCE SLACKFINISH WELDING SPILL GUARDS ON CANOPY.

20-Feb-2012 WOC123113 - BACK CHARGE 26,258 DAMAGE REPAIRS QTM3324

FEB 20, 2012 - WAYNE MATHIASENREPAIR STAIRS. REPAIR PAYLOAD SENSOR GUARD. REPAIR BROKEN GREASE LINE.

FEB 23, 2012 - BRUCE GREENWOOD (TUNDRA)TRAY INSTALLCLEAN PIN NORES ON TRAY. SET UP WITH WELDED AND INSTALL BOX, HAD TO BE SHIMMED AS WE DIDN'T HAVE ANY. BRING UNIT BACK TO SHOP AND CLEAN CYLINDER BORED AND INSTALL CYLINDER PINS. BACK UNIT OUT OF SHOP AND DUMP BOX. REMOVE CYLINDER STOPS AND CLEAN UP WELDS. CLEAN UP AND PUT AWAY BLOCKING USE TO SUPPORT BOX.

FEB 23, 2012 - DANNT HILLIERCHANGED ENGIN OIL; AND FILTERS, FILLED UNTI WITH HYDRAULIC OIL, TRANS OIL, STEERING OI, FILLED BOTH REAR FINAL DRIVED. REBUILT AIR DRYER. INSTALLED ALL NEW SEAT BELTS. INSTALLED POCKET IN PASSENGERS DOOR, INSTALLED NEW CIG LIGHTER. INSTALLED WALK WAY AND DRIVERSIDE. INSTALLED BOTH MIRRORS. CHECKED BACKK STUD CLEARANCES ALL WITHIN SPEC. TOPPED UP GREASE TANK AND GREASE BOTH ENGINE PULL UPS. BLED SERVICE BRAKES AND PARK BRAKE. INSTALLED REAT OUTSIDE WHEELS.

FEB 23, 2012 - ERIC OLSEN2000 HR SERVICEWIRE IN BOX LIGHTS. HOOK UP GREASE LINES TO HOIST CYLINDERS. LOOK UP PIN FOR FRONT BRAKES AND PLACE ORDER. RUN AND CHECK UNIT. CHECK ELECTRICAL BEHIND CAB - HORN NOT WORKING.

MAR 3, 3012 - LARRY JREPLACE BROKEN LEVER ON PARK BRAKE SWITCH. REPLACE CIGAR LIGHTER SOCKET.

14-Feb-2012 WOC122283 - BI-WEEKLY FEB 15 - FEB 22, 12 26,249




BI-WEEKLY FEB 15 - FEB 22, 12

FEB 19, 2012 - MELVIN BUTTERCLEAN EXTERIOR OF DUMP TRUCK

FEB 19, 2012 - LARRY NCAB DETAIL, REMOVE GARBAGE UNDER DEAT. WIP DOWN WINDOWS AND DASH. DO PARTS RUNTO FINNING.

FEB 19, 2012 - WAYNE MATHIASENSTEAM CLEAN MACHINE.

FEB 20, 2012 - MELVIN BUTLERPART RUNS INTO FORT MCMURRAY ADN FINNING LAKE. DROP PARTS TO TECH AT SITE.

FEB 20, 2012 - DALE BR & R BRAKED NOT WORKING. REAR SLACK ADJUSTER NOT WORKING. DIAGNOSE, ORDER PARTS,PICKED UP PARTS, REAPIR SLACK ADJUSTER,M BLEED BRAKES, TEST. OK.

FEB 20, 2012 - WAYNE MATHIASENGENREAL REPAIRSMOVE MACHINE FORN WASH BAY TOP BAY 4. DIAGNOSE SLACK ADJUSTER PROBLEM. REMOVESLACK ADJUSTER RE-SEAL, INSTALL AND TEST. BLEED BRAKES. TIGHTEN ALTERNATOR BELT.

FEB 20, 2012 - KEN OLMSTEADMOVE MACHINE FRON WASH BAY TO BAY 4CHECK BRAKE RIGHT REARCHECK PARK BRAKE AND SERVICE BRAKE PRESSURE (MAKE UP FITTINGS FOR FLANGE) NOPRESSURE AT CLACK ADJUSTER ON RIGHT SIDE ORDERED PARTS AND REBUILD RIGHT SIDE ANDRECHECK PRESSURE, BLEED AIR FROM SYSTEM. CHECK DRIVE SHAFTS UJOINTS AND REPLACEFLANGE ON AUF DRIVE SHAFT PUMP END.

FEB 20, 2012 - KEITH OINSHEET INSPECTIONINSPECT UNIT. MAKE DEFECT REPAIR LIST.

FEB 21, 2012 - DEAN FPERFORM SERV/REPAIRS. ORDERED PARTS. DECALS, GASKETS, SERV JIT. REMOVED ALL DECALS,CAT, CUSTOMER. INSTALL 2 CAT DECALS WAIT FOR 2 MORE. INSTALLED EMECO DECALS. DIDSOME PIN CHECKD, SEE SHEET. REMOVED ALL 4 BATTERIED. HOT TANK BATTERY HOLD DOWNS INPOOR CONDITION, CORROSION FROM LEAKING BATT. CLEAN HOLDS/PAINT. REPLACED BATT CABLEENDS THAT WERE BROKEN. CLEAN BATTERY BOX FULL OF GRAVEL. CHECK GREEASE INJECOTRSREPLACED 2.

FEB 21, 2012 - WAYNE MATHIASEN2000 HR SERVICECHANGE ENGINE OIL AND FILTERS. CHANGE FUEL FILTERS. CHANGE AIR FILTERS. STEERING OILAND FILTERS CHANGED. TRAN CHARGE FILTERS CHANGED. PARK BRAKE RELEASE FILTERCHANGED. REMOVE AIR DRYER AND DIMANTLE FOR SERVICE.

FEB 21, 2012 - DALE B2000 HR SERVICE, PICK UP PARTS/LEADHAND.

FEB 21, 2012 - ERIC OLSEN2000 HR PMCHANGE OUT FINAL DRIVES, FRONT HUBS AND DIFF OILS. DRAIN HYD OIL AND TRNASMISSIONOILS FROM TANK. REMOVE BOTH TANK COVERS AND CLEAN RESEVOIRS. REPLACE HYD HOSE INTANK. INSTALL COVERS.

FEB 21, 2012 - WARREN MACKENZIEREMOVE BROKEN BOLTS IN HAND RAILS ON LEFT SIDE OF TRUCK.

FEB 21, 2012 - DANNY HILLIERPERFORM 2000 HR SERVICEDID ALL OIL SAMPLES AND PAPER WORK. DRAINED HUD AND TRANS OIL TANKS. REMOVEDCOVERS AND INSEPCTED FOR DEBRIS. REPLACED HOSE IN HYDRAULIC TANK. RESEALED BOTHDRAINS IN TANKS. REINSTALLED BOTHER COVERS. REMOVED BOTH THE TRANS AND TORQUESCREENS AND INSPECTED. TRANS SCREEN DAMAGED - ORDERED NEW ONE. REMOVED DAMAGEDDECALS. CHANGED OILS IN DIFF, FINAL DRIVES, FRONT HUBS.

FEB 21, 2012- BRUCE GREENWOOD (TUNDRA)2000 HR SERVICEREPLACE TORQUE SCREEN. CHECK ON PARTS. START TO SERVICE GREASE SYSTEM.

FEB 22, 2012 - JOE ADEFECT LISTRUN TO NIS FOR REBUILD. GREASE LINE AND PICK UP SOME FITTINGS. INSTALL GREASE LINE AND




FITTINGS ON LH REAR STRUTS. REPAIR AI (DRYER). DRIVE.

FEB 22, 2012 - ERIC OLSENHYD OIL LEAKSREPLACE O-RINGS ON 4 HYD HOSES. REPLACE O-RING ON BRAKE RESEVOIR TANK.

FEB 22, 2012 - 2000 HR SERVICEINSTALL TRANS SCREEN. DRAIN TRANSMISSION AND FILL TANK. FILLED HYD TANK AND REMOVESCREEN AND CHECK OK. START C/O OF DECASENT ON AIR DRYER.

FEB 22, 2012 - BRUCE GREENWOOD (TUNDRA)TRANNY INSTALLHAUL BLOCKING ACROSS ROAD TO SET TRAY ON. SET UP TRUCKS AND WAIT FOR WELDCO.UNLOAD TRAY AND SET ON BLOCKS. LOCATE SER# AND TRY TO FIND UNIT NUMBER SER#AJA01837. LOCATE AND BRING PINS TO SHOP AND POLISH UP FOR INSTALL, REMOVE WELD ONFLANGES AND CLEAN UP.

FEB 22, 2012 - BRUCE GREENWOOD (TUNDRA)2000 HR SERVICECONTINUE TO VERIFY AND REPAIR. GREASE INJECTOR AND REPLACE AS NECESSARY. REPLACE LHTIERDO COVER. STRAIGHTEN AND INSTALL LOWER ENGINE GUARD.

FEB 22, 2012 - DEAN FCONTINUE WITH SERVICE., REPLACED ALL 4 BATTERIED ON UNIT. REPAIRED ONE SKID PLATETHAT WAS BENT. PUT IN PRESS AND STRAIGHTEN. TESTED ALL 4 BATTERY THAT CAME OUT 2 NOGOOD, 2 NEEDS CHANGE FOR BOOSTER. REPAIR ALL 3 TABS THAT HOLD SKID PLATES ON.REPAIRED LOAK AT DRAIN PLUG IN TANK. ORDERED PARTS FOR RECEIVER DRYER ( CANNOT BUYCOMPLETE UNIT). LOOK FOR WIGGINS FITTING (LEFT IN ON TANK FOR CROSS). CLEANED UPWORK AREA AFTER WORK COMPLETED. REPAIRED HYD LEAK ROD SCREENS COVER FOR TORQUEPUT NEW GASKET THAT WAS ON BENCH.

FEB 22, 2012 - DALE BSERVICE, PICK UP PARTS, HELP INSTALL CATWALK. LEADHAND

FEB 22, 2012 - KEITH OWEEKLY W/OASSIST TECHS WITH PARTS, TECHNICAL QUESTIONS.

FEB 23, 2012 - KEN OLMSTEAD2000 HOUR SERVICEINSTALLED AIR DRYER, DRAIN TANK AND R & R WIGGINS. FUEL FILL AND REFILL FUEL TANK. TOPUP TRANSMISSION, HYDRAULIC, STEERING AND ENGINE OIL. MEASURE BACKK STUD JOINT ONSTEERING CHECK LINKAGE. INSTALL CATWALK AND MIRROR. INSTALL NEW TRANSMISSIONSCREEN. CLEAN BREATHERS FOR TRANS/HYDRAULIC TANK AND FUEL TANK.

FEB 23, 2012 - KEN OLMSTEAD2000 HOUR SERVICEREMOVE FRONT STRUT COVERS AND CLEAN UP GREASE ON STRUTS. REMOVE REAR STRUT COVERSAND CLEAN UP COVERS AND STRUTS. INSTALL BRACE FOR CAT WALK ON DRIVERS SIDE. INSTALLMUDFLAPS ON FRONT FENDERS. CHECK FRAME AND CHASSIS FOR CRACKS. CHECK ON PAYLOAD,SENSOR PARTS ORDERED. REPAIR MOUNT FOR BOX DOWN SENSOR. PAINT DRIVERS DOOR FORUNIT #, IT HAD ALOT OF CLACK OVERSPRAY. REMOVE RIGHT BOX HINGE PIN AND INSTALL SHIMS.

FEB 23, 2012 - WAYNE MATHIASENFINISH 2000 HR SERVICE. C/O JUMPER SEATBELTS. REMOVE AND CLEAN STRUT CHROME COVERS.INSTALKL BRACE FOR CATWALK. INSTALL MUD FLAPS ON FRONT FENDERS. CHECK FRAME FORCRACKS, NONE FOUND. INSTALL SHIMS IN BOX PINS.

FEB 22, 2012 - WAYNE MATHIASEN2000 HR SERVICEINSTALL SERVICE KIT IN AIR DRYER. INSTALL AIR DRYER. PUMP OUT FUEL TANK TO C/O WIGGINS.TOP UP ENGINE OIL, TRANS OIL AND HYDRAULIC OIL. MEASURE BALL JOINT PLAY, ALL GOOD.INSTALL CATWALKS AND MIRRORS. INSTALL TRANS SCREEN. CLEAN DIFF BREATHER. CLEANTRANS TANK BREATHER.

FEB 23, 2012 - KEVIN LOWVALVE AND INJECTOR SET. CHECK OVER ENGINE.

FEB 23, 2012 - DEAN FNO TRAYINSTALL TRAY SET UP WITH WELDCO ACROSS ROAD AND INSTALL ON UNIT. T/S NO BRAKELIGHTES/CAB LIGHT AND REPAIR ROD CONNECTION AT BRACKET. T/S NO HORN AND ORDEREDPARTS FOR STEERING COLUMN FOR HORN. ORDERED SHIMS FOR BOX. HOOK UP HOIST CYLS.REPAIR BENT BRACKET FOR BOX DOWN SENSOR AT REAR. PERFORM 1000 HR BRAKE PRESSURETEST AND RECORD ON SHEET ALL GOOD.

FEB 23, 2012 - DEAN F




PICK UP PARTS AT LAKE.

FEB 24, 2012 - RICARTE VREPAIR RADIO AND HORN. ADD CHAIN FOR DRIVER DOOR SUPPORT. INSTALLED STEERINGCOLUMN COVER. BRAKE AND STEERING TEST.

FEB 24, 2012 - STAN STEWARTWORK ON 2000 HR SERVICEMOVE TO TIRE SHOPCLEAN BAY (SHOP)

FEB 24, 2012 - DEAN FSERVICEHOOK UP GREASE LINE TO RIGHT SIDE OF PIN, CHECK OTHER GREASE INJECTORS. LOCATE ROCKINJECTORS AND FIND PINS. GET UNIT READY MOVE TO YARD FOR TIRES TO BE INSTALLED. PAINRDC #'S ON FRONT, LEFT, RIGHT OF UNIT.

FEB 24, 2012 - KEVIN LOWHOOK UP GREASE LINES. INSTALL BOX PIN KEEPERS. INSTALL NEW DECAL ON LH FRONT FENDER.FIND AND INSTALLED MUD FLAPS. CHECK OVER TRUCK FOR ADDIDTIONAL REPAIRS. BRING ONROCK EJECTORS, CLEAN UP PINS. CLEAN UP AROUND TRUCK.

FEB 24, 2012 - LAWRENCE SLACKGUAGE AND CLEAN UP CANOPY. GUAGE OFF OLD SUPPERT ON SPILL GUARD. INSTALL ONE SPIKEGUARD.

FEB 25, 2012 - KEVIN LINDSAYREPLACE FRONT BRAKE PADS.REMOVED BRAKE PADS ON FRONT SIDE OF R FRONT. WRONG PARTS CAME IN, REORDERED PROPERPARTS.

FEB 25, 2012 - WARRN MACKENZIEFIND GPS UNIT IN DASH. REPAIR RADIO. REMOVE GPS. UNIT AND INSTALL IN BACK OF CAB, WIREPOWER AND GROUNF DIRECT TO BATTERY. ORDER PRESSURE SWITCHED FOR OIL AND PARKBRAKE, HELP WITH FRONT BRAKES

FEB 25, 2012 - SCOTT MINSTALLED ROCK EJECTORS ON UNIT.

1-Feb-2012 WOC120421 - BI-WEEKLY FEB 02 - FEB 14, 12 26,240BI-WEEKLY FEB 02 - FEB 14, 12

FEB 13, 2012 - DARRELL FEDORUKIN SHEETCHECK OVER UNIT (THEY WERE STILL USING SO HAD TO GET THEM TO STOP.)FRONT ROTOR'S AND PARDS ARE WORN, RIGHT SIDE MORE. LEFT GUARD ON LEFT REAR STRUT TO COVER SENSOR IS BENT. RIGHT GUARD AND WIRE ARE MISSING AND BROKEN TO THE RIGHT REAR STRUT. MISSING VENT COVER IN CAB. MISSING BOTH RUBBER DUST COLLECTOR CUPS ON AIRE BOXES. HOURS ON OIL FILTERS WROTE ON THEM AT TIME OF CHECK OVER ARE 26025.

19-Oct-2011 WOC104243 - INSPECTION 25,623Pictures , tire report, outsheet

OCT 14, 2011 - DARRELLINSPECTION - PICTURES, TIRE REPORT AT MT MULLIGAN

8-Dec-2010 WOC76549 - COLD START MACHINE 22,063COLD START MACHINE TO LOAD Cab was dirty. No owners manual. No EMECO decals.

COMPLETED NO OTHER INFO

24-Nov-2010 WOC74654 - CHANGE OUT TIRES 22,063Replace two front tires with new ones and put the used front tires on the left rear


24-Nov-2010 WOC74651 - R/R FRONT PADS 22,063




replace front brake pads both sides

NOV 27, 10 - JERAMEY/RICARTEBROUGHT MACHINE INTO SHOP. REMOVED CALIPER MEETING BOLTS EXCEPT ONE. REMOVED OILLINE AND SWING DOWN CALIPERS. REMOVED PIN RETAINING BOLTS AND REMOVED PINS.REMOVED OLD BRAKE LININGS. CLEANED ALL PART PIECES. PUSHED PISTONS BACK INTO CALIPER.INSTALLED NEW BRAKE LINES. REASSEMBLED CALIPERS AND PUT BACK INTO PLACE. INSTALLEDMEETING BOLTS AND TORQUED TO 563 FT. LBS. BLED BRAKES.

TO REPLACE FRONT BRAKE PADS - RENESHOVEL SNOW FROM WORKING AREA. REMOVE BOLTS FROM CALIPER ON FRONT BRAKES. LINESSTILL ON , BUT CALIPERS LOOSE.

21-Nov-2010 WOC74399 - REPLACE BALL STUDS 22,063REPLACING ALL THE BALL STUDS

REPLACE BALL STUDS ON THE RODS AND STEER CYLINDERSREPLACE RACES ON TIE RODS AND STEER CYLINDERSINSTALL AND HOOK UP LINES ON STEER CYLINDERSINSTALL TIE ROD ENDSTORQUE NUTS ON BALL STUDSHOOKED BACK UP GREASE LINES

21-Nov-2010 WOC74400 - VALVE SET 22,063SET ALL VALVES AND INJECTOURS

COMPLETED BY REECEVALVE SET AND VALVE TRAIN REPAIRS

21-Nov-2010 WOC74401 - B/S TEST 22,063CHECK STEERING AND BRAKES

COMPLETEDNO OTHER INFONOT SIGNED

21-Nov-2010 WOC74403 - REPAIR DOG BONE 22,063BUILD UP BUSHING HOLES AND LINE BORE

NOV 22, 10 - IRON SMITHSET UP WELDING MACHINE. MECHANICS HAD TO JACK TRUCK UP FOR ENOUGH ROOM FOR WELDING MACHINE TO FIT. WELD BORES. SET UP LINE BORE MACHINE.

NOV 22, 10 - IRON SMITHSET UP LINE BONE AND BORED OUT BORES THAT WE BUILT UP WITH WELD WITH LINE BORE WELDER. HAD TO REWELD ONE BORE AND REBORE IT. CLEAN UP ALL TOOLS AND MACHINES.

NOV 23, 10 - DOG BONE REPAIR - CORY S / CLINT SREMOVE DOG BONE AND BUSHINGSBUILD UP A ND BORING OF BUSHING BORES BY IRONSMITHINSTALL BUSHINGS IN BOXESINSTALL DOG BONE

21-Nov-2010 WOC74402 - PREP FOR MOVING 22,063REMOVE BOX,TIRES ,CAT WALK

NOV 23, 10- SHAWNREMOVED CAT WALK, BOLTS ARE DOUBLE BAGGED, LABELED AND TIE STRAPPED TO CAT WALK. CATWALK IS LABELLED. REMOVED MIRROR, LABELLED, BOLTS, DOUBLE BAGGED AND TIE STRAPPED TO MIRROR.

20-Nov-2010 WOC74350 - DEFECTS 22,063fix minor repairs

DONE NO MORE INFOR

20-Nov-2010 WOC74351 - 2000 HR SERVICE 22,063




change oils and filters

REECECHANGED FRONT WHEEL HUB OILCHANGE HYDRAULI COIL AND FILTERSCHANGED L/H FINAL DRIVE OILINSTALL STEERING CYLINDER AND TORQUED NUTSGET BOX READY TO REMOVEREMOVE CUSTOMER UNIT #'SINSTALL WINTER FRONT

CHANGED FUEL FILTERS, PRIMED SYSTEM, CLEANED SCREENCHANGED TRANNY OIL AND FILTERS, FILLED TANK, WILL NEED MORE AFTER START UP.CHANGED STEERING TANK AND FILTERS, FILLED WITH OIL, CHECK AFTER START.FINISHED TAKING SAMPLES EXCEPT FINAL DRIVESDID CHECKS, SOME WE COULD NOT DO , TAGGED OUT.CHANGED AIR AND CAB FILTERSTIRE REPORT DONEREPLACED O-RING ON REAR LEFT COOLING TUBE THAT WAS LEAKINGREPLACED O-RING ON HOIST PUMP AND HOSE,REPLACED O-RING ON RELIEF VALVE FOR PARK AND SECONDARYREPLACED REAR RIGHT CLEARANCE LIGHT.

20-Nov-2010 WOC74309 - INSHEET OIL SAMPLES 22,063DO IN SHEET AND OIL SAMPLES

COMPLETED BY DAN

20-Nov-2010 WOC74349 - WASH 22,063wash machine


12-Nov-2010 WOC73508 - RRO TIRE (2NEW ON FRONT) 21,636RRO TIRE (BUBBLE ON SIDE)

JOE WIPF CALLED IT IN MACHINE AT SUNCOR HE SENT A TRUCK AT NIGHT SHIFT 2 PICK THEM UP

REPLACE 2 FRONTS WITH NEW AND PUT THE FRONTS ON THE REAR, INSTALL THE 2 SUPPLIED RUN OUTS ON THE REAER

WE SUPPLIED 2 NEW AND 2 USED (EMCA 656, 657, 881, 883)

KMC INSTALLED

16-Oct-2010 WOC72560 - 1500 HR PM SERVICE (KMC) 21,3351500 HR PM SERVICE COMPLETED BY KMC

24-Sep-2010 WOC68958 - BRAKES OVERHEATING 21,077




TROUBLESHOOT BRAKES OVER HEATINGCHECK 4 SQUEEKING NOISE

SEPT 24, 10 - SQUEAKING GRINDING NOSE - GRANTDIG ROCK OUT OF FRONT BRAKE PADS, DRY BRAKES.

SEPT 24, 10 - HIGH TEMP ALARM POWERTRAIN - GRANTTRAVEL TO MACHINE, HIGH TEMP ALARMS ON BRAKE HYD TEMP X 2 TIMES. TEST DROVE WITHOPERATOR, NOTICED BRAKES DRAGGING . SENT TO SHOVEL PAD. TEST PARK BRAKE RELEASEPRESSURE, FOUND 300 PSI ONLY AT IDLE. TESTED ANOTHER TRUCK, IT HAD 680 PSI. NOTICEDNEW TREADS VALVE ON MACHINE, ALSO LOOKS LIKE NEW COMPONENTS. RING EMECO, FADIE WASOFF SITE SO UNABLE TO CHECK PREVIOUS REPAIR. TRAVEL TO KMC, GET NEW PARK BRAKE RELIEFVALVE P/N 6E-6305. TRAVEL BACK, CHANGE PARK BRAKE VALVE. RETEST, INCREASED TO 370 PSIAT IDLE, STILL TOO LOW. CALLED FOR SOMEONE TO RUN TRUCK, WAIT 30 MIN, RUN AND TEST ATHIGH IDLE, FOUND 800PSI, DROPPED TO 500 AT LOW IDLE AND SLOWLY BLEED DOWN TO 300 PSIOVER TWO MINUTES AND HELD. WENT BACK TO KMC SHOP AND STARTED READ UP ON SYSTEM.

SEPT 25, 10 - LOW PARK BRAKE PRESSURE - GRANTTRAVEL TO MACHINE FROM WI STOCKPILE TO SYNCRUDE SHOVEL PAD LAYDOWN. FLRA LOCKS ANDCHOCKS. START AND WARM UP OILS ON MACHINE. CONNECT GAUGES TO REAR WHEEL. REMOVEAND CHECK PARK BRAKES FILTER. FOUND CLEAN. REINSTALL. INSTALL TEST FITTING INTO PARKBRAKE FILTER HOSING. READ THROUGH REPARTS ON PREVIOUS REPAIRS. TEST RELEASEPRESSURE, FOUND ABOUT 450 PSI. OIL STILL COOL, WAY TOO LOW, ONY 450 PSI, CAP OFF OILSUPPLY TO TORQUE CONVERTER. LOCKUP CLUTCH FOUND STILL AT 450 PSI. END OF SHIFT SOPARK UP. SUSPECT PUMP MIGHT HAVE FAILED. WILL REMOVE VALVE AND CHECK. SPOOLS IS FREEAND NO BROKEN SPRINGS.

SEPT 26, 10 - T/SHOOT LOW PARK BRAKE PRESSURE - GRANTTRAVEL TO SITE, TO KMC. SIGN IN AND TRAVEL TO MACHINE IN FIELD. LOCK AND CHOCK, PINBOX AND FLRA. FLAG OFF TRUCK BOX. REMOVE PARK BRAKE CONTROL VALVE. STRIP AND CLEAN.FOUND 14-2644 CHECK VALVE HAD CRACKED LOWER 6V8350 O-RING CRACKED IN 3 PLACES ANDBAKED HARD. CHECK PARTS AT KMC AND FINNING. PARTS ORDERED. COMING FROM EDMONTON.

SEPT 27, 10 - LOW PARK BRAKE PRESSURE - GRANTSTART AND WARM UP MACHINE. INCREASED BY 20 PSI WITH HOT HOIL. ORDER BRAKE AND T/QPUMP. PUMP ONLY 2 MONTHS OLD "POSSIBLE WARRANTY FINNING".. PACK UP TOOLING.

SEPT 30, 10- DARRENSET UP @ UNIT AND USED SPOONS TO HOLD OIL IN TANK ADN REMOVED LINES. REMOVEDTORQUE/PARK BRAKE PUMP. WNT TO INSTALL NEW ONE AND NEEDED SOME O-RINGS . HAD TOORDER FROM FINNING. CLEANED UP AND DROVE TO FINNING. WAITED FOR PARTS TO BE PICKED .DROVE BACK TO UNIT AND FINISHED. INSTALL, CALL FOR LUBE TRUCK TO TOP UP HYDRAULICSAND RAN UNIT AND CHECKED PRESSURES, GOOD . 500 PSI @ LOW IDLE AND 750 PSI @ HIGHIDLE, CLEANED UP.

31-Aug-2010 WOC70687 - 250 HOUR SERVICE 21,035250 hour service carried out by KMC

14-Aug-2010 WOC64556 - WHEEL SEAL LEAK 20,863Possibly a hose on the brake cooling system leaking.

AUGUST 13,10: WHEEL SEAL LEAK:TVL TO MACHINE VERY MUDDY AND SLIPPERY. GOT STUCK , HAD TO BE TOWED OUT WITH D/O CHECK LEAK. LOOKS LIKE A HOSE ON WHEEL BRAKE CODING. LEFT MACHINE AS D/O LEAVING AREA AND HAD TO BE TOWED OUT.

AUGUST 19,10: L/R UPPER BRAK ECOOLER PIPE, CRACKED AND LEAKING:DRIVE TO KMC SHOP AT BASE MINE. CHECKED OUT LEAK AT L/R WHEEL. FOUND L/R UPPER BRAKE COOLING PIPE CRACKED AT FLANGE ON WHEEL END. PICKED UP PARTS AT FINNING.DROVE BACK TO KMC.REMOVED AND REPLACED PIPE AND CHECKED FOR LEAKS WAS OK. TOPPED UP OIL.

11-Aug-2010 WOC66250 - 325 HR SERVICE 20,890KMC DID A 325 HR SERVICE NO DATE JUST HRS 20890

9-Aug-2010 WOC63518 - SEAT 20,792




REPAIR BROKEN SEAT.

AUGUST 8,10: SEAT BROKEN:DRIVE TO MACHINE. FILLED OUT FLRA, LOCKED AND CHOCKED UNIT OUT OF SERVICE. CHECKSEAT-FOUND NUTS MISSING ON SET BACKREST ON THE LEFT SIDE ALSO FOUND SHOCK BROKEN INSEAT BASE . NEED TO ORDER PARTS.

AUGUST 9,10: SEAT BROKEN:DRIVE TO UNIT, FILLED OUT FLRA, LOCKED AND CHOCKED UNIT. REMOVED OPERATOR SEAT, ANDREPLACED SEAT WITH ONE FROM RDC050. TOOK SEAT BACK TO SHOP FOR REBUILD.

AUGUST 13,10: REPLACE SEAT RUBBED FOR RDC028:WHILE AT THE TRUCK REASSEMBLED SEAT AND FOUND SHOCK ADJUSTER CABLE HAD COME OUT OFPLACE, REPAIRED IT AND CRANED THE SRAT UP INTO THE TRUCK AND INSTALLED.

8-Aug-2010 WOC63472 - 1200 HR F/S 20,9661200 HR FIRE SUPP PM AT KMC.

AUGUST 23,10:1200 HR INSPECTION ON HAULER # RDC028. ENGINE SHUTDOWN WORKS, ACTUATIN GREASED + TESTED. NO PANEL OR REWIRE AS IT AS MANUAL. HOSING TIGHT AND IN GOOD SHAPE. PORTABLES UPDATED FOR MONTHLY. 2 NOZZLES CAPS REPLACED.

2-Aug-2010 WOC62691 - TILT COLUMN REPAIR 20,734INSTALL NEW TILT MECHANISM IN THE COLUMN:Remove decals.

AUGUST 2,10: REMOVE DECAL SON RDC013,RDC030,RDC028, REPLACE FIRE EXT. ON RDC030,CHECK PLAY IN STEERING COLUMN ON RDC028 AND ODERD PARTS:DRIVE TO KMC MILDRED LAKE. REMOVED DECALS ON FORESAID MACHINES. REPLCED FIRE EXTINGUISHER AND BRAKCET ON FRONT BUMPER OF RDC030. DROVE TO KAL TIRE YARD CHECK STEERING COLUMN TILT PLAY ON RDC028 FOUND IT NEED A TILT STEERING STOPPER KIT REPLACED , ORDERED PARTS, DROVE BACK TO SHOP.

AUGUST 24,10:FRONT BRAKE SQUEALLIN, TO MUCH PLAY IN TILT STEERING MECHANISM:DRIVE TO MACHINE, FILLED OUT FLRA, CHECK FRONT BRAKE PADS AND ROTORS, ALL FRONT BRAKE PADS ARE GOOD AND MEASURE BETWEEN 12M AND 13MM LIGHT SCORING ON ROTORS AND DIRTY. ALSO ONE ANCHOR PIN ON R/S FRONT INNER WAS JUST BARELY TOUCHING ROTOR. IT HAD BEEN PUSHED IN TOO FAR. I ALSO ADJUSTED AL NCHOR PINS TO HAVE A 1/8" GAP BETWEEN THEM AND THE ROTORS. AND CLEANED BOTH SIDES WITH BRAKE CLEAN. INSPECTED STEERING COLUMN TILT FOR PLAY. FOUND IT NEEDED NEW STOPPERS, RS STOPPER WAS MISSING. REPLACED BOTH STOPPERS AND CHECKED WAS OK. CALLED CUSTOMER AND NOTIFIED THAT MACHINE IS READY TO USE.

SEPT 23, 10 - STEERING TILT - GRANTTRAVEL TO MACHINE, CHECK STEERING TILT COLUMN, FOUND TILT SPRING OFF, REINSTALL. NOTICED 3 TEETH SMASHED OFF ON TILT COLUMN. REMOVE WHEEL CHOCKS AND LOCK OUT.

1-Aug-2010 WOC62596 - REPLACED LRI TIRE 20,645Tire starting to separate.

18-Jun-2010 WOC57847 - R&R FUEL TRANSFER PUMP 20,572RHR FUEL TRANSFER PUMP.CHANGED OUT FUEL TRANSFER PUMP. CLEANED OUT FUEL SCREENS AND VALVES.

2-Jun-2010 WOC55608 - BRAKES SQUEALING 20,533TROUBLESHOOT BRAKE AND P-BRAKE PROBLEM-BRAKE SQEALING-CHECK PRESSURES-CHECK OPERATIONS

PARK BRAKE NOW ALWAYS RELEASINGFRONT BRAKE PADSFUEL PUMP LEAKINGHYDRAULIC TANK CAP

2-Jun-2010 WOC55578 - 300 HR PM 20,533300 HR PM SERVICE MACHINE WITH GRAHAM

21-May-2010 WOC54439 - SEAT BASE/ FIRE EXT 20,472RPLACE BROKEN SEAT BASE ( HAD ONE IN SHED)INSTALL FIRE EXT DONE BY JOE

20-May-2010 WOC54277 - UNIT #'S 20,467INSTALL UNIT #'S ON MACHINES RENTED TO GRAHAM




3-May-2010 WOC52577 - INSTALL ROCK KICKER 20,395ROCK KICKER TOO WIDE FOR TIRES. INSTALL NARROW ONE.

1-May-2010 WOC52443 - ON SITE INSPECTION 20,395WALK AROUND INSPECTION WITH CUSTOMER - ON -SITE

COMPLETED BY HENRY AND DUSTIN

23-Apr-2010 WOC51769 - INSTALL PARK BRAKE INDICATOR 20,386Inspect Unit.

APR 21, 10 - OUTSHEET - GRANT OTRAVEL TO NORTHGATE. CARRY OUT OUTSHEET INSPECTION

APR 25, 10 - INSTALL PARK BRAKE INDICATOR LIGHT ON CAB - GRANT OBOOST TRUCK. RAISE AND PIN BOX. MOUNT INDICATOR LIGHT TO CAB. RUN WIRING THROUGH CAB. CONNECT POWER TO BREAKER. INSTALL TEE AND AIR PRESSURE SWITCH TO PARK BRAKE RELEASE AIR PRESSURE. TEST OK. REASSEMBLE, PACK UP AND CLEAN UP. TRAVEL BACK TO SHOP.

17-Apr-2010 WOC50847 - WELD HANDRAIL MOUNT/DECALS 20,385WELD CRACKS ON FRONT OF TRUCK WHERE HAND RAIL MOUNTS TO

19 APRIL 10

REMOVE ALL EMECO DECALS AND LETTERS FROM UNIT #

COMPLETED BY ARC ANGEL

9-Apr-2010 WOC49962 - BRAKE & STEERING TEST 20,385Complete forms and submit

APR 09, 10 - BRAKE AND STEERING TEST - DUSTINTROUBLESHOOT WHY SECONDARY STEERING WOULDN'T ACTIVATE WHEN HIT E-STOP SWITCH. TIED WIRE AROUND STRING UP TO CAB. TOOK UNIT OUT OF YARD AND ON THE MOVE ABOUT 3RD GEAT HIT E-STOP SWITCH, UNITS SECONDARY STEERING ACTIVATED UNTIL UNIT CAME TO COMPLETE STOP. GOOD TO GO.PERFORMED A BRAKE AND STEERING TEST. ****THERE IS A GREASE NIPPLE AND CAP AND SNAP RING ORDERED TO BE PUT ON R/H SIDE TIRE ROD LINK.

7-Apr-2010 WOC49589 - TRAY INSPECTION 20,384MEASURE TRAY AND ENTER ON TO INSPECTION SHEET - COMPLETED BY WOODY

7-Apr-2010 WOC49609 - REPAIR GREASE SYSTEM 20,385REPAIR CRACK ON RH PLATFORMHIGH BEAM LIGHT NOT HOLDINGREVERSE INDICATOR NOT WORKING REPAIR GREASE LINE ON REAR STRUTLOW GREASE PRESSURE

APR 08, 10 - AARONPHONED FINNING MECHANIC, MYLES NELSON ABOUT EMERGENCY SHUTDOWN. HE SAYS NEWER ECM'S ARE PROGRAMMED DIFFERENT AND NEED TO HAVE GROUND SPEED SHOWING BEFORE IT WILL ENGAGE EMERGENCY STEERING. FINNING SOFTWARE SHOUL SHOW DEFINED SHUT DOWN.

5-Mar-2010 WOC45788 - BOX REPAIRS 20,383REPAIR CRACKS ON BOX

MAR 04, 10 - CRACK FOUND IN BOX - MIKE (MPI)LIFT UP BOX AND CLEANED OUT DIRT SO IT WAS SAFE TO WORK UNDER. AIR ARC OUT CRACK TO BACK IN PLACE AND REWELDED.

28-Feb-2010 WOC45247 - IN SHEET INSPECTION 20,383oil sampleCOMPLETED BY GRANT OOut sheet inspection

28-Feb-2010 WOC45232 - BACK CHARGE 20,383




Install fire extinguisherremove broken fog lightFUEL @ 60%LEFT STEP RUBBER TORNRIGHT REAR STRUT GREASE LINE BROKEN

FEB 27, 10 - MISSING FIRE EXTINQUISHER, AMBER FLOOD LIGHT ON BUMPER SMASHED OFF. -GRANTREMOVE SMASHED LIGHT AND ALSO NON DAMAGED LIGHT. INSTALL NEW 20LB FIREEXTINQUISHER AND ADJJ BRACKET.

26-Feb-2010 WOC45129 - 1200 FIRE SUPPRESSION 20,3801200 HR FIRE SUPPRESSION COMPLETD BY ROY

UPON CHECKING HISTORY ON UNIT, WE NOTICED IT WAS DUE. BLEW 1/4", & 3/4" LINES. UPON DOING ENGINE SHUTDOWN, IT WOULD NOT WORK AFTER TROUBLE SHUTDOWN. WE FOUND WIRE DISCONNECTED. CONDUCTED ENGIEN SHUTDOWN. CHECKED, CLEANED, REGREASED ACTUARIES. CHECKED PORTABLE EXTINQUSIHER, DID ANSUL SYSTEM OK.

25-Feb-2010 WOC50635 - RECONDITION WHEEL ENDS 20,3822 x Wheel Groups sent to Finning Red Deer for reconditioning, inconjunction with WOC15754

20-Feb-2010 WOC44324 - 2000 HOUR SERVICE(WARRIOR) 20,378PERFORM 2000 HOUR SERVICE COMPLETED BY WARRIORFILL OILEVAC WASTE OILDISPOSE FILTERSFUEL TRUCK AND PICK UP FILTER KIT

APR 07, 10 - 2000 HR SERVICE - DUSTINORDER PARTS NEEDED TO FINISH SERVICE. GO THROUGH CHECK LIST. BRAKE/PAR/SERVICE/RETARDER, STALL TESTS. TROUBLESHOOT LUBE SYSTEM, FIX INJECTOR, FILL GREASE KEG TEST. CHANGE BREATHERS. PULL SUCTION SCREWS. CHECK BALL STUDS, TIE RODS, NOSE, A-FRAME, DOG BONE, HOIST PINS. TEST UNIT OPERATOR.

APR 08, 10 - 2000 PM, SECONDARY STEERING ISSUE - DUSTINFINISH 2000 HR PM SERVICE. CHANGE BREATHERS, REBUILD AIR DRYER, PURGE VALVE, CHECK VALVE. DO A TIRE REPORT, CHECK TREADS AND TIRE PRESSURES. MEASURE SUSPENSION HEIGHTS. DO ANY CHECKS ON SHEETS. CHECK BEVEL GEAR THRUST PIN PRE-LOAD. WHEN HIT ENGINE SHUT DOWN, EMERGENCY STEERING DON'T ACTIVATE. CHECKED FUSES, TESTED RELAYS, STUDIED SCHEMATICS. DIDN'T GET ANYWHERE ON FIXING PROBLEM.

17-Feb-2010 WOC43862 - START UP AND MOVE MACHINE 20,380START UP AND MOVE TRUCK FROM MINE SITE TO SYNCRUDE NORTH GATE

FEB 26, 10 - DEAD, WON'T START - GRANT OBOOST BATTERIS OFF WELDER, EITHER SOAK AIR INLET FILTER, STARTED OK. WARM UP AND CHECK OVER. CHECK BATTERIES. LOAD TESTED OK.

23-Dec-2009 WOC38173 - REPLACE FOG LIGHT 19,291REPLACE FOG L/H FOG LIGHTREPAIR L/H STEPINSTALL 20 LB FIRE EXT.

DEC 23, 09 - CHECK BROKEN LIGHT - RICARTELOOSE FIRE EXTINQUISHER. CHECK FOR LIGHT. CHECK OVER MACHINE FOR ANY DEFFICIENCIES.

14-Dec-2009 WOC36972 - TRANS NOT SHIFTING 19,087DIAGNOIS/REPAIR TRANS NOT SHIFTINGDIAGNOIS BATTERY LIGHT

DEC 14, 09 - BENHAD LOST OF TROUBLE FINDING MACHINE. FOUND BATTERY LIGHT ON, TESTED ALT AND FOUND GOOD, 14V FROM RIGHT TERMINAL. NOTHING AT MONITORING. CHECKED WIRING AND FOUND BAD PIN CONNECTOR IN HARNESS, FIXED AND TESTED. ALSO, SPENT ABOUT 4 HRS LOOKING FOR RT15. TURNS OUT RT15 WAS THE TRUCK I FIXED. BUT HAS RT10 ON IT. DROVE EVERYWHERE LOOKING FOR TRUCK.

DEC 14, 09 - UNIT NOT SHIFTING FRONT TO REAR - DUSTINTESTED UNIT, AND NOTHING. LIFTED BOX AND CHECKED FOR BROKEN OR DAMGED WIRES. CONTINUOUSLY TRIED TO MOVE SHIFT LEVER FROM FRONT TO REAR AND NOTHING. UNCOUPLED PLUGS AND CONNECTORS, CLEANED AND REASSEMBLED. TRANNY THEN STARTED WORKING. TOOKED FOR A TEST DRIVE DOWN ROUGH TERRAIN. SHIFTING BACK AND FORTH REPEATEDLY. SIMULATED OPEARTION OF LIFTING BOX, SHAKING UNIT, HAVING BOX HIT FRAME. USED PARK BRAKE OVERRIDE SWITCH, SEEING IF THAT WAS THE CAUSE. EVERYTHING SEEMED TO WORK FINE. WENT FOR LOAD WITH OPEARATOR, WORKED GOOD.




12-Dec-2009 WOC36747 - OUT INSPECTION 19,021OUT INSPECTION - COMPLETED

11-Dec-2009 WOC36616 - COLD START ENGINE 19,087-45 C WARM UP AND START MACHINE

DEC 11, 09 - HENRYPUT HERMAN NELSON TO HEAT UNIT. INSTALLED THE PRO-HEAT THEN IT BROKE DOWN, WE HAD TO INSTALL A FUEL LINE, BECAUSE IT BROKE AND THEN WE FIRED IT BACK UP. BOOSTED UNIT AND DROVE INTO THE SHOP.

7-Dec-2009 WOC35838 - INSTALL TIRES (KAL - TIRE ) 19,021INSTALL TIRES COMPLETED BY KAL-TRIE

KAL TIRE INV 328059890

LABOUR INCLUDES SERVICE CALL TO FT. MCKAY IND PARK.1-2700R49 LOOSE MOUNT1-2700R49 ROTATION TO LEFT REAR OUTER OF UNIT RDC028HAD TO BRING THE LOOSE TIRE BACK TO THE SHOP TO AIR UP AS THE SUB ZERO WEATHER HAD AN IMPACT.

25-Nov-2009 WOC30237 - INSTALL BOX/ROCK KICKERS 19,018INSTALL BOX

GARNET AND RICARTECHECKED OVER AND COLD STARTED TRUCK. PREPPED FOR BOX INSTALL. SET BOX ON FRAME AND INSTALLED AND SHIMMED PIVOT PINS. CONNECTED HOIST CYLINDER TOP PINS.

NOV 26, 09 - GARNETCONNECTED GREASE LINES AND ELECTRICAL FOR BODY.

NOV 27, 09 - GRANT OSMANBOOSTED TO GET RUNNING. BATTERYS FLAT. REPLACED MISSING NEUTRAL RUN / ENG COVER P/N 9D2817. HAD ONE ON BOARD OF SERVICE TRUCK. TROUBLESHOOT PARK BRAKES WARNING LIGHT, FOUND OVER STROKES PIN OUT. BLED REAR BRAKES. FOUND STILL IN ALARM. TEST OVER STROKES SWITCH FOUND OBJECTIVE. SWITCH REPLACED.

NOV 30, 09 - GARNETINSTALLED ROCK KICKERS

23-Nov-2009 WOC29112 - WASH/ CLEAN 19,010WASH / CLEAN -COMPLETED BY SAHWN

20-Nov-2009 WOC28908 - CHARGE STRUTS 19,010CHARGE STRUTS

NOV 19, 09 - GRANTGATHERED UP ENOUGH PARTS TO INSTALL NITROGEN IN FRONT STRUTS (PARTS SPREAD ALL OVER SHOP). STARTED TRUCK, MOVED OUT INTO AREA WHERE IT COULD BE WORKED ON. CHARGED STRUTS 8 1/2" - 9".

3-Nov-2009 WOC26896 - REMOVE TRAYS AND PREPARE FOR T 19,005Remove trays and prepare for transport.

8-Sep-2009 WOC21550 - SAMPLES FD AND DIFF 19,005Install Fog lightsran power off main magnetic switch to a circuit breaker behind the cabinstalled circuit breaker - install switch in cab - ran harnees from cab to front bumper of the machine - secured wiring harness - welded light brackets on the front bumper installed lights - connected wiring - tested light circuit - okay.

8-Sep-2009 WOC21615 - WHEEL GRP HOUSING REPAIR 19,005disassemble wheel group so casting repairs can be performed.Wheel group reassembled.

12-Aug-2009 WOC18401 - INSTALL BOX/PREP FOR SERVICE 19,005Install box and check for adjustment, charge susp cyl's and final checks

11-Aug-2009 WOC18362 - PREPARE BOX FOR LOADING 19,005PREPARE BOX FOR LOADINGMAMMOET LOADED BOXES - COMPLETED

10-Aug-2009 WOC18187 - FIRE SUPPRESSION 19,005




FIRE SUPPRESSION DONE BY LEVITTE

REMOVED AND GREASED ACTUATORS AND PNEUMATIC ACTUATOR TESTED THEN FUNCTIONED WELL.REPLACED CRACKED CHECK VALVE, BLEW OUT LINES WITH NITROGEN AND REPLACED . NEEDEDBLOW OFF CAPS AND TESTED SHUTDOWN.

6-Aug-2009 WOC17910 - REVERSE TIRES FOR TRANSPORT 18,999INSTALL TIRES

REVERSE TIRES FOR TRANSPORT - COMPLETED

6-Aug-2009 WOC17957 - REPAIR FRONT BRAKES 19,005REPAIR FRONT BRAKESREPLACE CALIPERSREBUILD CALIPERSKAL -TIRE INSTALLED REAR TIRES

ALL COMPLETED

JACKED UP FRONT WHEELS. DISASSEMBLED CALIPERS/BRAKES. GET READY TO R/R BRAKE DISCS.BRAKE DISCS ARE ROUGH, PADS ARE WORN. REPLACING CALIPER SEALS AND WHEEL SEAL.KAL-TIRE INSTALLED REAR TIRES. REMOVED FRONT TIRES

GRANT/GARNET

DISASSEMBLED FRONT BRAKE CALIPERS AND PREPPED FOR CLEANING AND REBUILD.

GRANT/GARNET

R/R BOTH FRONT WHEEL HUBS. CHANGED BOTH BRAKE DISCS, REPLACED DU CONE WHEEL SEALS, RESHIMED FRONT WHEEL BEARINGS.

GRANT/GARNET

REBUILT ALL FRONT BRAKE CALIPERSINSTALLED THEM ON UNITADDED, FILLED FRONT WHEEL HUB OIL.

GRANT/GARNET

FINISHED INSTALLATION OF FRONT BRAKE ASSEMBLIESBLED BRAKE CALIPERS AND CHECKED OPERATIONINSTALLED "OPERATORS POCKET" INTO RH CAB DOOR PANEL AND REPLACED MISSING HARDWAREINSTALLED LH FRONT SUSP CYLINDER SKIRT ON RDC028 ROBBED FROM MTC023

5-Aug-2009 WOC17444 - REPLACE MISSING ROCK EJECTORS 19,005Weld on missing bracket. Customer misplaced original parts given to him.

REPLACE MISSING ROCK EJECTORSWELD ON BRACKET - DONE

27-Jul-2009 WOC16639 - REMOVE TRUCK BOX 18,999Mammoet

REMOVE TRUCK BOX - COMPLETED

22-Jul-2009 WOC16369 - PARK BRAKE VALVE LEAKING OIL 19,005




PARK BRAKE VALVE LEAKING OILCHECK STEERING CYLINDER MOVEMENTCHANGE MANOMETER ON AIR FILTER HOUSINGCHECK TORQUE OUTPUT SHAFT SEAL, CHANGE IF NECESSARYCLEAN BATTERY POSTSENGINE LEAKING OIL R/H SIDE OF ENGINE (DRIPPING ON TORQUE COOLER)OPERATOR SEAL - SEAT DOESN'T SLIDE FREELY - CHECK SEAT SHIMS ETC., REPLACE IF NECESSARYREPLACE 777D DECALS ON BOXREPLACE OPERATORS MANUALCHECK BRAKE DISCS FOR MIN THICKNESSLHS AUTOLUBE INJECTOR CAPS LOOSEREPOSITION SUSPENSION CYLINDER COVERSOIL LEAK AT DIFF THRUST CAP

REPAIR SID ELIGHT - DONEREPLACE PUMP DRIVE SHAFT U-JOINTS AND PUMP DRIVE SEAL - DONETRANS SCREEN TO TRANS, TRANS VENT HOSE - DONE

CHECKED ALL LEVELSLIGHTS/AC / WIPERS ETCCLEANED CABINSTALLED DECAL

20-Jul-2009 WOC16298 - INSHEET AND OIL SAMPLES 18,998INSHEET AND OIL SAMPLES - COMPLETED

17-Jul-2009 WOC16098 - EXTEND BOX SIDES 18,999EXTEND BOX SIDESRemove boxPaint extensionsReplace Decals

ALL COMPLETED

12-Jul-2009 WOC15769 - CHECK FRT BRAKES FOR WEAR 19,005Check all u - joints (main and pump)Check all functions including A/CInspect machine for defects prior to disassembly

CHECK FRONT BRAKES FOR WEAR - DONECHECK ALL U-JOINTS - DONECHECK ALL FUNCTIONS INCLUDING A/C INSPECT MACHINE FOR ANY DEFECTS PRIOR TO DISASSEMBLYREPLACE SWAY BAR BUSHINGS - DONEREPLACE STEERING CYLINDER BALLSTUDS INNER - DONETROUBLE SHOOT - TRANS NEUTRALIZER LIGHT - DONEreplace frt brakes linings changed, calipher kits installed ETC

12-Jul-2009 WOC15772 - RESEAL REAR STRUTS 19,005Rebuilt here.

RESEAL RAR STRUTS - DONE

R/R STRUT SEALSINSTALL STRUTS ON TRUCKCHECK ADJUST BRAKE(PARK) RELEASE PRESSURE 725 PSI SERVICE BRAKE 700PSI

REMOVE STRUTS (DISASSEMBLE - ORDER PARTS)RUN UNIT - TOP UP LUBESREPAIR SIDE LIGHT

FIRE SUPPRESSION WOULD NOT SHUT DOWN ENGINE. FIRE SUPPRESSION WAS HOOKED TO STARTING AID WIRING. JIM FROM FINNING REWIRED SHUT DOWN INTO ECM

REMOVED ALL BLOCKING LOWERED UNIT. PUTA AWAY ALL BLOCKS/ JACKS CLEANED UP WORK AREA

12-Jul-2009 WOC15766 - CHANGE DIFF 19,005




Finning rebuild

CHANGE DIFF

DRAINED DIFF, BOTH FINAL DRIVES, TRANS OILS

R/R BOTH FINAL DRIVE WHEEL GROUPS

R/R DIFFREMOVE PUMP DRIVE LINE AND REAR SEALTORQ WHEEL GROUP MOUNTING BOLTS

12-Jul-2009 WOC15754 - REPLACE REAR WHEEL GRPS 19,005Finning rebuild

REPLACE WHEEL GROUPSSET/CHECK BRAKE PRESSURESSERVICE REAR 700PSIPARK BRAKE RELEASE 725 PSI

FINISHED WHEEL GROUPS, LINES, AXLES, PUMPED IN SOME OIL

CHANGED PUMP DRIVE SHAFT- U JOINTS AND PUMP DRIVE SEAL

CHANGED MAIN DRIVE SHAFT V-JOINTS

FINISHED TRANS/DIF INSTALLATION

CHANGED HOSES TRANS FILTER TO TRANS, TRANS SCREEN TO TRANS, TRANS VENT HOSE

INSTALLED ADUSTED SLIDER IN OPERATOR SEAT

25-Jun-2009 WOC14822 - A/C NOT WORKING 18,947Hyd hose has a pin hole leak - COMPLETEDOil leak by engine cooler - COMPLETEDA/C NOT WORKING - COMPLETED

HYDRAULIC LEAK - NO A/C

REPLACED HYDRAULIC LINE OFF OF THE FRONT OF THE BRAKE COOLER

REPAIRED ELECTRICAL CONNECTORADDED 2 LBS 134A FREEON

24-Jun-2009 WOC14807 - MACHINE INSPECTION FIELD 18,946Kevin Weir

MACHINE FIELD INSPECTION - COMPLETED

15-Jun-2009 WOC14280 - LUBE SYSTEM & REPAIR 18,886lube system & repair

27-May-2009 WOC13255 - CHANGE ROCK EJECTOR 18,886change rock ejector - COMPLETED

11-May-2009 WOC12356 - VALVE SET 18,886VALVE SET - COMPLETED

29-Apr-2009 WOC11848 - RENTAL RETURN INSPCT/FINNING 18,852INSPECT MACHINE

RENTAL RETURN INSPECTIONINSPECTED MACHINE AS PER CHECK LIST SUPPLIED BY THE CUSTOMERMADE UP LIST OF PARTS NEED FOR THE REPAIRS

17-Apr-2009 WOC11038 - OUT SHEET 18,852check machine over - COMPLETED

16-Apr-2009 WOC10963 - WASH MACHINE 18,848clean machine - COMPLETED

2-Apr-2009 WOC10111 - AIR COMPRESSOR REPAIR 18,848




AIR COMPRESSOR - REPAIRED BY FINNING UNDER WARRANTY

CLEANED DIRT OFF COMPRESSOR, SCRAPED GASKET OFF BLOCK AND COMPRESSOR. CLEANED UPMESS

REMOVED COMPRESSOR, DRAINED AND FILLED COOLANT. CHANGED GASKET, INSTALLEDCOMPRESSOR, TORQUED MTG BOLTS TO 75 FT. LBS. TOOKE PICTURES FOR WARRANTY CLAIM

21-Mar-2009 WOC9273 - REPLACE AC IDLER PULLY 18,851REPLACE AC IDLER PULLY - DONE

15-Mar-2009 WOC8846 - REPAIR OIL LEAKS 18,848REPAIR OIL LEAKS -

REPAIRED HYDRAULIC OIL LEAKS - DONE

COLD START - HEAT UP - CHECK OUTDRAIN AFTER COOLER COOLANT LEVEL REWORKED REAR GREASE LINES

REPLACE BOX CORNER LIGHTRSROB AMBER LIGHTS FROM VOLVOCOLD START , CLEAN OUTER CAB GLASSREPAIR TRANSCOOLER BY -PASS LINE LEAKING

TIGHTEN BOLTS ON SIDE COVERS, 5 COVERS HAD LOOSE BOLTS. ONLY #12 WAS LEAKING BAD. CHECKED ALL

15-Mar-2009 WOC8847 - REPAIR BRAKES 18,848REPAIR BRAKES, PARK BRAKE RELEASE PRESSURE TO LOW - COMPLETED

13-Mar-2009 WOC8730 - CHANGE FINAL DRIVE OILS 18,848CHANGE FINAL DRIVE & STEERING OIL - COMPLETED

13-Mar-2009 WOC8729 - BRAKE & STEERING TEST 18,848BRAKE & STEERING TEST - COMPLETED

4-Mar-2009 WOC8094 - FIRE SUPPRESSION 18,836FIRE SUPPRESSION DONE BY LEVITTE

23-Feb-2009 WOC7351 - HOIST CYLINDERS R/R 18,848removing hoist cylinder to send in and get repaired - COMPLETED

22-Feb-2009 WOC7314 - LANCE PINS 18,848L Roberts will lance the top hoist cylinder pins - COMPLETED

FEB 22 - DANIEL P LANCE TWO PINS FOR BOX AND WELD TWO NUTS FOR PULLERFEB 23 - DANIEL P FINISH LANCING PINS AND REWELD NUTS ON PINS FOR PULLERFEB 26 - GEAR UP TRUCK AND WENT OVER TO EMECO AND FINISH LANCING LIFT CYLINDER PINS

19-Feb-2009 WOC7222 - BALL STUDS 18,848Replacing ball studs on right hand cylinder Both - COMPLETED

17-Feb-2009 WOC7006 - REPAIR ENGINE OIL LEAKS(FINNIN 18,848REPAIR ENGINE OIL LEAKS - FINNING UNDER WARRANTY - COMPLETED

TIGHTEN BOLTS ON SIDE COVERS5 COVERS AHAD LOOSE BOLTSONLY #12 WAS LEAKING BADCHECKED ALL

CLEANED DIRT OFF COMPRESSORSCRAPED GASKET OFF BLOCK AND COMPRESSORCLEANED UP MESS

REMOVED COMPRESSOR DRAINED AND FILLED COOLANTCHANGED GASKETINSTALLED COMPRESSORTORQUED MTG BOLTS TO 75 FT LBSTOOK PICURTES FOR WARRANTY CLAIM

17-Feb-2009 WOC7008 - ALTERNATOR REPAIR 18,848




ALTERNATOR REPAIR - COMPLETED

CHANGE OUT ALTERNATOR - BY FINNINGCHECKED OUT LATERNATOR - DETERMINED FILED AND IN NEED OF REPLACEMENT. CUSTOMERSUPPLIED PARTSINSTALLED NEW ALTERNATOR AND TESTED FOR PROPER OPERATION - ALL OK

15-Feb-2009 WOC6900 - REPAIR A FRAME BEARING 18,835REPAIR A FRAME BEARING

JACKED UP THE MACHINE, REMOVED THE GUARDS, SHAFTS AND A-FRAME MOUNTING BOLTS. LOWERED THE A-FRAME AND REMOVED THE BLOCKS, PIN AND BEARING. THE BEARING WAS BROKEN INTO SEVERAL PIECES AND THE BORE WAS ERODED AND WILL BE BUILT UP AND REBORED. DRAINED THE FUEL TANK. ORDERED PARTS.

11-Feb-2009 WOC6722 - 500HR PM 18,848500 HR. PM.& REPAIRS - COMPLETED

HOIST CYLINDERS LAKING - DONEAIR DRYER NEEDS REPLACING - DONEAIR SEAT DOESN'T WORK - DONEAIR HORN - DONEAIR COMPRESSOR SEAL - DONELEFT TOP HOIST BEARING BROKE - DONENOSE CONE BUSHING NEEDS REPLACING - DONEALTERNATOR NEEDS REPLAING - DONE RHS STEERING CYLINDER BALL JOINTS GONE - DONE REAR TAILLIGHTS NOT WORKING - DONE LEAKING HOIST LINE - DONE WINDOW WATER PUMP BROKEN - DONE LEFT HAND SIDE STEP NEEDS NEW STRAPS - DONE REBUILD AIR DRYER - DONE REPAIR LH UPPER HOIST CYLINDER BEARING - DONE REPLACE MISSING HEATER VENTS - DONE REPAIR REAR RAIL BRAKE LIGHTS - DONE REPAIR HORN - DONE REPAIR TILT STEERING - DONE REPAIR WINDOW WASHER - DONE INSTALL PRO HEAT - DONE ROCKER INJECTOR MISSING - DONE RIGHT HAND CYLINDER BALL STUD - DONE

30-Jan-2009 WOC5998 - STEAM CLEANING BY BIRCH MOUNT 18,810STEAM CLEANING BY BIRCH MOUNTAIN - DONE

23-Dec-2008 WOC4517 - R&R ENGINE - FAILURE 18,309




removed valve covers found #2 cylinder bad

WRAPPED THE TRUCH WITH PARACHUTEAND INSTALLED HEATED SYSTEM

Finning removed and replaced engine on site, installed P/X Engine, original engine installed at 16335hours failure at 18308 hours

Bleow is copy of e mail to SAles Group outlining the failure and action being taken to rectify

Have received verbal confirmation this morning that the engine failure in RDC028 will notbe covered by warranty, failure is related to cold weather running, the elevated idle switch for thismachine was deactivated in line with Petro Canada operating policies

We have been able to secure this engine to rebuilt to our requirements rather than go back into theExchange system where the cost to rebuild this engine will be in the $155K mark.

What this means is that we will have to carry out a component change-out within the next 4 months aswe have made a commitment to Finning that we will have their core back to them by July 2009, it alsomeans that the cost to Petro Canada will be kept to a reasonable amount rather than paying for anexchange unit, labour to R&R the engine will be to Petro Canada's account

We will have a back-charge quote ready by the end of the week to coincide with Finning's report andquote to repair

We will have reports by the end of the week from Finning and OEM to support the decline of warrantyon this engine

See attached some photos of the failure, below is earlier findings from the first examination of theengine, the transmission that failed in the same truck is warranty and not customer related

Attached are pics of the engine some of the early findings / observations are as follows," Engine was not dry appears to a lot of oil down both sides of the block and flywheel housing, latertraced this to slobbering from the exhaust end of the turbo's" Both turbo's are seized, unable to spin these by hand" Major carbon / soot / oil build up in the exhaust snail trumpets" #7 exhaust bridge missing" #2 dropped valve (exhaust)" Valve lash on some of the cylinders appears to be very excessive" Engine does not smell good, very acidic smell and sooty

The engine will be apart for inspection on Friday morning, have asked for a SOS, valve clearancebefore pulling heads, but at this stage we are looking down the barrel for this one based on the engineidle switch being in the wrong position, Finning have not said as much but that is the way it will belooking, not unless something comes out of the strip down, may pay to discuss with Ross and putPetro Can on notice that this could be their baby

22-Dec-2008 WOC4483 - CHECK EXHAUST LEAK 18,265CHECK EXHAUST LEAK - DONE

CHECK ENGINE FOR EXHAUST LEAK, ALL LOOK OKRUBBER ON THE WINDOWS AND DOORS OKNO LEAKSCHECKED EXHAUST ON BOX AND PIPES NO LEAKS OKTHE CAB FILTER WAS COMPLETELY BLACKREMOVED THE FILTERTHE RUBBER ON THE DOOR IS NOT DAMAGED MUCH BUT SHOULD PROBABLY BE REPLACED

HENRY

17-Dec-2008 WOC4416 - RE & RE TRANNY 18,071




REPLACE, INSTALL TRANSMISSION AND INSTALL TRAN PUMP

HOOKED UP TRAILER, WENT TO FINNING TO GET RRANSMISSION AND TRANS PUMDROVE TO FORT HIL, THE STEAMER WASN' T THERE SO JIM CALLED IN FOR FORT HILLS TO STEAMTHE UNIT2 HRSREMOVED THE DRIVED SHAFT AND DISCONNECTED THE HYDRULIC LINESFINNING MECHANICS PULLED OUT THE TRANSMISSION WITH THE CRANEINSTALLED NEW TRANSMISSION AND O-RINGSCONNECTED THE HYDRAULIC LINES AND BOLTED THE DRIVE SHAFT AND TORQUE TO 230 FT / LGSAND REPLACED NEW BOLTS.I PUT BLUE LOCKTIEFROM FORT HILLS TO FINNING SHOP MIDLAKE RETURN THE CORECLEAN THE SERVICE TRUCK

RE & RE TRANNY

WARRANTY REPAIR FROM FINNING

SUPPLIED ASSISTANCE

Finning:travel to fort hills3 hours

customer complained that the machine would not move and that the pump pressure was low. checkedthe machine and it would move. checked the trans pump pressure and it was 365 @ idle hot.checked the suction screen and it was full of clutch material and the magnets were full of metal. thetrans is failing. checked the torque lockup pressure and it was 300psi. installed a photo tach on thedrive shaft to confirm the lockup clutch was not slipping. ok. ordered a trans and pump and all relatedparts. arranged for the machine to be steam cleaned.6.5 hours

travel to fort hills3 hours

traveled to fort hills to remove the trans. the steamers did not show up and the machine was notsteamed. moved the machine and fort hills had agreed to steam the machine. there was 25 tonsfrozen in the body. we had the body scraped out and the machine was cleaned. we drained the oilsand removed the trans and installed the new one. hooked up all lines and drive shaft.9 hours

travel to fort hills3 hours

11-Dec-2008 WOC4357 - F/R BRAKES 18,071REPLACE RIGHT FRONT BRAKE CALIBERS

MOVE TRACK INTO YARD FROM SHOPBLOCK WHEELS LOCK OUTREMOVE BRAKE LINESUNBOLT CALIBERS AND USE CRANE TO REMOVETHEN REINSTALL NEW CALIPERS AND BRAKE LINESSET UP PAD PINSBLED FIL OUT OF SYSTEMCHECKED FOR LEAKSCLEANED UP

25-Nov-2008 WOC4156 - REPLACE FRONT BRAKE PADS 17,771RE & RE R/S FRONT ROTOR, BRAKE PADS AND CALIIBERS

RE & RE R/S FRONT ROTOR, CALIBERS AND PADSSTARTED TO REPLACE L/S BRAKE PADSFINISHED REPLACING BRAKE PADSBLED BOTH R/S AND L/S BRAKES

-----------------

Brake oil leaking from the right brake calipersThe shoes were worn completely and the pistons had come out and were rubbing the rotorThe rotor is damaged and the backing plates are rubbing the discThe disc is damaged as wellTraveled to the mine and checked the heater on rdcle for rdc029 and noticed that the brake linings are worn out on that unitMade up a parts list for fort hills to repair the units because they are responsible for the repairs

4-Nov-2008 WOC3874 - CHECK WINDOW UP DOWN 17,288




TROUBLESHOOT WINDOW UP/DOWN FUNCTION

DISASSEMBLED DOOR ASSSEMBLYREMOVED WINDOW REGULATORFOUND STRIPPED TEETH ON REGULATORASSEMBLED DOOR ASSEMBLY

ORDERED PARTS

TOOK OFF OLD WINDOW SECTORINSTALLED NEW ONE

21-Oct-2008 WOC3733 - CHECKOVER 16,805BRING IN UNITSDO COMPLETE CHECK OVERGET FEED BACK FROM OPERATORS WHEN FUELING U PGO OVER UNITSSIT PASSENGER ON FEW LOADS TO SEE OPERATING CONDITIONS

11-Oct-2008 WOC3664 - REPAIR HORN 16,805REPAIR OIL LEAK ON ENGINE - DONE

9-Oct-2008 WOC3639 - VALVE SET/OIL CHANGE 16,515SET VALVE LASH ON NEW ENGINECHANGE FILTERS (CAT ONE OPEN)CHANGE ENGINE OIL

30-Sep-2008 WOC3555 - REPAIR LIGHTS 16,515FIX EMECO EQUIPMENT

CLEAN TRANNY BREATHER TUBEREPLACE TRANNY BREATHERREMOVE AND REPLACE SECONDARY PARK BRAKE SENSORTROUBLESHOOT AND DIAGNOSE PROBLEMTIGHTEN UP LOOSE CONNECTION

INSPECT UNITLOOK INTO PAYLOAD SCALE NOT WORKINGFIX BOX LIGHTS

check brake, steering and lock up pressuresfix air leakexhaust bypass solenoid failedtopped up hydraulic oilfix lightsreplaced washer motor and other engine filtersstarted machine and brought it up to tempchecked the steering pressure and it was 3000 psichecked the brake and retarder pressure and the brake pressure was lowchecked the air pressure and raised it to 120 psirechecked the brake pressure and it was 740 psi

23-Jul-2008 WOC3053 - PREPARE FOR RENT 16,3402000 HR PM SERVICE - DONEREBUILD ENGINE - FINNING - DONEEXCHANGE TORQUE - FINNING - DONEEXCHANGE TRANSMISSION - FINNING - DONETRAN PUMP, HOISE PUMOPM STEERING PUMP CHANGED - DONEHYDRAULIC HOSES - DONERAD SENT OUT TOBE CLEANED - DONESTEERING CYLINDER - DONESTEERING CYLINDERS NEED REPLACING - DONEREAR RIGHT FINAL DRIVE COVR LEAKING, DIFF PLUG LEAKING - DONECLEAN PLYLOAD LIGHT CONNECTIONS - DONEINSTAQLL DECALS - DONEINSTALL NUMBERS ON FRONT GRILL - DONEREMOVE ROCK EJECTORS - DONEINSTALL STRUT BOOTS - DONECLEAN CAB - DONERESEAL PAYLOAD SENSORS ON BAR STRUTS. CHECKED O.K. - DONE

DIAGNOSTIC CHECK - STARTED THE MACHINE AND BROGHT IT UP TO TEMPERATURE. CHECKED THE STEERING PRESSURE AND IT WAS 3000 [SI. CHECKED THE BRAKE AND RETARDER PRESSURE AND THE BRAKE PRESSURE WAS LOW. CHECKED THE AIR PRESSURE AND RAISED IT TO 120 PSI. RECHECKED THE BRAKE PRESSURE AND IT WAS 740PSI AND RETARDER WAS 640 PSI. CHECKED TORQUE LOCKUP. 290 PSI AIR LEAK AT THE BRAKE VALVE. LORNE PARK REPAIRED IT.


picture to come · negotiated sales for heavy equipment & industrial assets 2004 caterpillar...

Documents