pipes, tubes, fittings, flanges
TRANSCRIPT
Technical CataloguePipes • Tubes • Fittings • Flanges
Revision 1
ahlsell 3
ConTenTs
1. INTRODUCTION 4 – 9 Presentation of Ahlsell Oil & Gas AS
Typical products and materials of typical pipes, fittings and flanges available from stock
2. PIPES - ASME B36.10 AND ASME B36.19 11 – 19 Pipe Schedule Chart – in inch and mm versions
Dimensions and weights of ASME B36.10 pipes
3. TUBES - ASTM A269 21 – 25 Metric and Fractional sizes
4. BUTT WELD FITTINGS – ASME B16.9 AND MSS SP-75 27 – 43 ASME B16.9 Elbows (LR), Tees, Reducers, End caps, Stub-ends, Return bends (LR)
ASME B16.28 Elbows (SR), Return bends (SR)
MSS SP-43 Stub ends – type A
MSS SP-75 Elbows (LR), Tees, Reducers, End caps,
5. MANIFOLD FITTINGS 45 – 47 Manufacturers dimensions
6. FLANGES – B16.5 49 – 65 ASME B16.5 Weld-neck, Blind, Slip-on, Socket-weld, Lap-Joint, Threaded
7. FLANGES – MSS SP-44 67 – 73 MSS SP-44 Weld-neck, Blind
8. FLANGES – API 6A 75 – 79 API 6A Type 6B and 6BX
9. FORGED FITTINGS – ASME B16.11 AND BS3799 81 – 93 ASME B16.11/BS3799 – Threaded and socket welding -
Elbows, Tees, Crosses, Couplings, Caps, Bushing, Plugs, Nipples, Unions, Welding boss
10. O´LETS 95 – 107 Manufacturers standard – O´let types:
Buttweld, Elbow, Lateral, Nipple, Insert Branch, Flanged Buttweld, Flanged Nipple
11. WEIGHTS 109 – 119
4 ahlsell
CoMPAnY PResenTATIon
How to contact us
Stavanger Office
Phone: +47 51 57 39 00Fax: +47 51 81 86 50E-mail: oil&[email protected]
Internet:www.ahlselloilgas.com
Visit address:Gamle Forusvei 534033 Stavanger
Postal address:PO box 80554068 Stavanger
Bergen Office
Phone: +47 51 57 39 00Fax: +47 55 94 48 40E-mail: oil&[email protected]
Internet:www.ahlselloilgas.com
Visit address:Godviksvingene 1745179 Bergen
Postal address:PO box 51 Godvik5882 Bergen
Abu Dhabi Branch Office
Phone: +971 2 634 9999Fax: +971 2 632 17 11E-mail: [email protected]
Internet:www.ahlselloilgas.com
Postal address:c/o EMDAD LCCPO box 4118Abu Dhabi, U.A.E
ahlsell 5
CoMPAnY PResenTATIon
Ahlsell Oil & Gas AS was in 2007 demerged from
Ahlsell Norge AS. The roots of the company date back
to 1933, when Bergens Rørhandel was established and
to 1955, when Stavanger Rørhandel was formed.
These two locations – Bergen and Stavanger in Norway
– are still the same for the demerged company
Ahlsell Oil & Gas AS.
Ahlsell Oil & Gas AS is a stockist of piping, supplying
mainly the Norwegian market, but exports to the
international market are also increasing.
Ahlsell Oil & Gas AS is considered to be one of the
leading stockists in Europe, for the oil & gas industry.
Ahlsell Oil & Gas AS is 100% owned by Ahlsell AB
in Sweden, which in turn is a private limited company
owned by Cinven and Goldman and Sachs.
Typical products and materials in stock
Products in stock:• Pipe, fittings and flanges from 1/2”-24”.
• Valves (Gate,Globe,Ball,Check, Butterfly)
• Filters and strainers.
• Mechanical joints.
• Compact flanges.
• Special Items.
Material qualities in stock:• Carbon steel
– ASTM A106 gr.B/A234 WPB/A105
– ASTM A333Gr.6/A420 WPL6/A350 LF2
– API 5L Gr. X52/ASTM A860 WPHY52/A694 F52
• 316/316L Stainless steel
• 6Mo (UNS S31254, UNS N08926)
• 22 Cr Duplex (UNS S31803)
• 25Cr Duplex(UNS S32750/760/550)
• Superaustenite (UNS S34565)
• Titanium Gr. 2.
This is a very brief overview of our stocking program,
as a complete list of finished products and raw mate-
rial covers more than 6000 items.
More detailed information of products and materials
of pipes, fittings and flanges can be seen at the next
pages.
6 ahlsell
Types of pipes, fittings and flanges in stock
Sizes and material types:The below listed products are typical available from our stock in size range from 0.5” to 24”. Larger sizes and other materials may also be available on request.
Material properties / certification:Material purchased to our stock are manufactured, tested and certified in accordance to our internal specification SB-2000, with modified requirements stated in the respective Material Data Sheets (MDS) as detailed below.These modified requirements are based on the Norsok MDS’s and the StatoilHydro MDS’s. All products are certified to EN10204 type 3.1.
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM A333 6 - Welded pipe ASTM A671 CC60, CC70 12, 22 for t>19mm S2, S7 Wrought fitting ASTM A420 WPL6 A960 S51, S53, S69 Forging/flange ASTM A350 LF2 1 A961 S55
Material purchased to our stock are modified to our internal data sheet MDS SBC11, e.g: Chemical: C≤ 0.20%; Mn = 0.50-1.35%; S≤ 0.025%; P≤ 0.025%; CE = C + Mn/6 + (Cr+Mo+V)/5 + (Cu+Ni)/15 ≤ 0.43 Impact: 27J average/20J single at -46 degree C, for thicknesses above 6mm
Carbon steel - Type 235LT
Product Standard Grade Class Suppl. requirement Seamless pipe API 5L X52 SR 4.3/SR 18 Wrought fitting ASTM A860 WPHY52 Smls & welded Forging/flange ASTM A694 F52
Material purchased to our stock are modified to our internal data sheet MDS SBC21/ -22, e.g: Chemical: C≤ 0.20% /C≤ 0.16% for X52; Mn = 0.90-1.60%; Si = 0.10-0.50%; S≤ 0.025%; P≤ 0.035%; Ti≤ 0.05%; Nb≤ 0.04%; Al≤ 0.06%; N≤ 0.015%; V+Nb+Ti≤ 0.10%; V+Nb≤ 0.07% CE = C + Mn/6 + (Cr+Mo+V)/5 + (Cu+Ni)/15 ≤ 0.43 Impact: 40J average/30J single at -46 degree C, for thicknesses above 6mm
Carbon steel - Type 360LT
Product Standard Grade Class Suppl. requirement Seamless pipe ASTM A519 AISI 4130 Wrought fitting ASTM A234 AISI 4130 Seamless S2 Forging/flange ASTM A788 AISI 4140 S18 Forging/flange API 6A 60K (AISI 4130) PSL 3 Material purchased to our stock are modified to Norsok data sheet MDS X01, X02 and X04, e.g: Chemical: Pipe and fitting: S≤ 0.025%, P≤ 0.025% Tensile: Pipe and fitting: Yield (0.2%) ≥ 415MPa, UTS ≥ 620MPa, A5 ≥ 18% A788 forging: Yield (0.2%) ≥ 620MPa, UTS ≥ 850MPa, A5 ≥ 15% API 6A 60K: Yield (0.2%) ≥ 414MPa, UTS ≥ 586MPa Impact: 42J average/ 30J single at -30 degree C, for thicknesses above 6mm
High strength, low alloyed steel - Type 4130/4140
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM A106 B Welded pipe API 5L B PSL1 ASTM A672 C60, C70 12, 22 for t>19mm Wrought fitting ASTM A234 WPB Forging/flange ASTM A105 Material purchased to our stock are modified to our internal data sheet MDS SBC01, e.g: Chemical: C≤ 0.20 %; Si≥ 0.10%; Mn = 0.50-1.35%; S≤ 0.025%; P≤ 0.025%; CE = C + Mn/6 + (Cr+Mo+V)/5 + (Cu+Ni)/15 ≤ 0.43
Carbon steel - Type 235
ahlsell 7
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM A312 TP316/TP316L
Welded pipe ASTM A312 TP316/TP316L
ASTM A358 316/316L 1, 3, 4 and 5
Wrought fitting ASTM A403 WP316/WP316L S, W, WX
Forging/flange ASTM A182 F316/F316L
Tube ASTM A269 316/316L Material purchased to our stock are modified to our internal data sheet MDS SBS01, e.g: Chemical: C≤ 0.035% Tensile: Yield (0.2%) ≥ 205MPa, UTS ≥ 515MPa
Austenittic Stainless steel - Type 316/316L
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM A312 UNS S31254* Welded pipe ASTM A358 UNS S31254* 1, 3 and 5 S3 Wrought fitting ASTM A403 WP S31254* S, W, WX A960 S51, S52, S70 Forging/flange ASTM A182 F44 (S31254)* A961 S56 Tube ASTM A269 UNS S31254* Material purchased to our stock are modified to our internal data sheet MDS SBR11/-12/-13/-14/-18, e.g: Grades *: UNS N08367 and UNS N08926 are acceptable in addition to the above grade Corrosion test: ASTM G48 method A, 50 degree C/24h, max 4g/m2 weight loss, no pitting
Austenittic Stainless steel - Type 6Mo
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM A790 UNS S31803 Welded pipe ASTM A928 UNS S31803 1, 3 and 5 S3 Wrought fitting ASTM A815 UNS S31803 S, W, WX S2, S7 Forging/flange ASTM A182 F51 A961 S56 Tube ASTM A789 UNS S31803 Material purchased to our stock are modified to our internal data sheet MDS SBD41/-42/-43/-44/-48, e.g: Chemical: N = 0.14-0.20% Impact: 45J average/35J single at -46 degree C, for thicknesses above 6mm Hardness: Max 290 HV10 (or 28HRC or 271HB) Micro: Ferrite level 35-55% for base, 35-65% for weld areas. No phases or precipitates.
Ferritic/Austenittic Stainless steel - Type 22Cr duplex
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM A790 UNS S32760* Welded pipe ASTM A928 UNS S32760* 1, 3 and 5 S3 Wrought fitting ASTM A815 UNS S32760* S, W, WX S2, S7 Forging/flange ASTM A182 F55 (S32760)* A961 S56 Tube ASTM A789 UNS S32760* Material purchased to our stock are modified to Norsok data sheet MDS D51/-52/-53/-54/-58, e.g: Grades*: UNS S32750/F53 and UNS S32550 are acceptable in addition to the above grade Chemical: PRE (Cr + 3.3xMo + 16xN) ≥ 40.0 Tensile: Yield (0.2%) ≥ 550MPa, UTS ≥ 800MPa (795MPa for wld pipe/750MPa for tube) Impact: 45J average/ 35J single at -46 degree C, for thicknesses above 6mm Hardness: Max 330 HV10 (or 32HRC or 301HB) Micro: Ferrite level 35-55% for base, 35-65% for weld areas. No phases or precipitates. Corrosion test: ASTM G48 method A, 50 degree C/24h, max 4g/m2 weight loss, no pitting
Ferritic/Austenittic Stainless steel - Type 25Cr duplex
8 ahlsell
TyPes oF PiPes, FiTTings and Flanges in sTock
Product Standard Grade Class Suppl. requirement
Welded pipe ASTM A358 UNS S34565 1, 3 and 4 Wrought fitting ASTM A403 UNS S34566 S, WX Forging/flange ASTM A182 F49
Material purchased to our stock are modified to Statoil data sheet MDS S65, e.g: Tensile: Yield (0.2%) ≥ 415MPa, UTS ≥ 795MPa Hardness: Max 34HRC Micro: No deleterious intermetallic phases or precipitates. Corrosion test: ASTM G48 method A, 50 degree C/24h, max 4g/m2 weight loss, no pitting
High strength Austenittic Stainless steel - Type Superaustenite
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM B861 2 Welded pipe ASTM B862 2 Wrought fitting ASTM B363 WPT2/WPT2W Forging/flange ASTM B381 F2 Tube ASTM B338 2 Material purchased to our stock are modified to Norsok data sheet MDS T01, e.g: Grades: Equivalent grades (GOST VT 1-0) is acceptable if complying with above standards
Titanium - Grade 2
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM B466 UNS C70600 Welded pipe ASTM B467 UNS C70600 Wrought fitting UNS C70600 Forging/flange UNS C70600 Material purchased to our stock are modified to Norsok data sheet MDS K01, e.g: Dimensions: In accordance to respective EEMUA standards - No.144, 145, 146
Copper alloy - Type CuNi 90/10
Product Standard Grade Class Suppl. requirement
Seamless pipe ASTM B444 UNS N06625 Welded pipe ASTM B705 UNS N06625 1 Wrought fitting ASTM B366 UNS N06625 S3 Forging/flange ASTM B564 UNS N06625 Tube ASTM B444 UNS N06625
Material purchased to our stock are modified to Norsok data sheet MDS N01, e.g: Heat treatment: All products shall be annealed
Nickel alloy - Type Inconel 625
ahlsell 9
10 ahlsell
ahlsell 11
PIP
ES
PIPesAsMe B36.10AsMe B36.19
12 ahlsell
PiPe schedule charT [inch]
ASME B36.19-B36.10 – pipe dimensions in inch and weights in kg
NOTE: Light blue values are wall thicknesses in inch, darker blue values are weights in kg/m. Specific steel weight used for calculation is 8.0, Titanium weight is approximately 57% of the table values,
NPS = Nominal Pipe Size - description of pipe size in inch, O.D = Outside Diameter of pipe, Sch5S and 10S do not permit threading according to ANSI B1.20.1, Sch40S and 80S in the table are applicable up to and including 12”.
NPS O.D. (INCH) (INCH) 5 S 5 10 S 10 20 30 STD 40 60 XS 80 100 120 140 160 XXS 40 S 80 S
1/8 0,405 0,049 0,057 0,068 0,095
0,3 0,3 0,4 0,5
1/4 0,540 0,065 0,073 0,088 0,119
0,5 0,5 0,6 0,8
3/8 0,675 0,065 0,073 0,091 0,126
0,6 0,7 0,9 1,1
1/2 0,840 0,065 0,083 0,095 0,109 0,147 0,187 0,294
0,8 1,0 1,1 1,3 1,6 2,0 2,6
3/4 1,050 0,065 0,083 0,095 0,113 0,154 0,219 0,308
1,0 1,3 1,4 1,7 2,2 2,9 3,7
1 1,315 0,065 0,109 0,114 0,133 0,179 0,250 0,358
1,3 2,1 2,2 2,5 3,3 4,3 5,5
1 1⁄4 1,660 0,065 0,109 0,117 0,140 0,191 0,250 0,382
1,7 2,7 2,9 3,4 4,5 5,7 7,9
1 1⁄2 1,900 0,065 0,109 0,125 0,145 0,200 0,281 0,400
1,9 3,2 3,5 4,1 5,5 7,4 9,7
2 2,375 0,065 0,109 0,125 0,154 0,218 0,344 0,436
2,4 4,0 4,5 5,5 7,6 11,1 13,4
2 1⁄2 2,875 0,083 0,120 0,188 0,203 0,276 0,375 0,552
3,8 5,3 8,0 8,6 11,4 14,0 20,4
3 3,500 0,083 0,120 0,188 0,216 0,300 0,438 0,600
4,6 6,5 9,9 11,3 15,3 21,4 27,7
3 1⁄2 4,000 0,083 0,120 0,188 0,226 0,318
5,2 7,4 11,4 13,6 18,6
4 4,500 0,083 0,120 0,188 0,237 0,337 0,438 0,531 0,674
5,8 8,4 12,9 16,1 22,3 28,3 33,5 41,0
5 5,563 0,109 0,134 0,258 0,375 0,500 0,625 0,750
9,5 11,6 21,8 31,0 40,3 49,1 57,4
6 6,625 0,109 0,134 0,280 0,432 0,562 0,719 0,864
11,3 13,8 28,3 42,6 54,2 67,6 79,2
8 8,625 0,109 0,148 0,250 0,277 0,322 0,406 0,500 0,594 0,719 0,812 0,906 0,875
14,8 20,0 33,3 36,8 42,6 53,1 64,6 75,9 90,4 100,9 111,3 107,9
10 10,75 0,134 0,165 0,250 0,307 0,365 0,500 0,500 0,594 0,719 0,844 1,000 1,125 1,000
22,6 27,8 42,4 51,8 60,3 81,6 81,6 96,0 114,8 133,1 155,2 172,3 155,2
12 12,75 0,156 0,180 0,250 0,330 0,375 0,406 0,562 0,500 0,688 0,844 1,000 1,125 1,312 1,000
31,3 36,0 49,7 65,2 73,9 79,7 109,0 97,4 132,1 159,9 187,0 208,1 238,8 187,0
14 14,00 0,156 0,188 0,250 0,312 0,375 0,375 0,438 0,594 0,500 0,750 0,938 1,094 1,250 1,406
34,4 41,3 54,7 67,9 81,3 81,3 94,6 126,7 107,4 158,1 195,0 224,7 253,5 281,7
16 16,00 0,165 0,188 0,250 0,312 0,375 0,375 0,500 0,656 0,500 0,844 1,031 1,219 1,438 1,594
41,6 47,3 62,6 77,8 93,3 93,3 123,3 160,1 123,3 203,5 245,6 286,6 333,2 365,4
18 18,00 0,165 0,188 0,250 0,312 0,438 0,375 0,562 0,750 0,500 0,938 1,156 1,375 1,562 1,781
46,8 53,3 70,6 87,7 122,4 105,2 155,8 205,7 139,2 254,6 309,6 363,6 408,3 459,4
20 20,00 0,188 0,218 0,250 0,375 0,500 0,375 0,594 0,812 0,500 1,031 1,281 1,500 1,750 1,969
59,3 68,6 78,6 117,2 155,1 117,2 183,4 247,8 155,1 311,2 381,5 441,5 508,1 564,8
22 22,00 0,188 0,218 0,250 0,375 0,500 0,375 0,875 0,500 1,125 1,375 1,625 1,875 2,125
65,2 75,5 86,5 129,1 171,1 129,1 299,3 171,1 373,8 451,5 527,0 600,6 672,3
24 24,00 0,218 0,250 0,250 0,375 0,562 0,375 0,688 0,969 0,500 1,219 1,531 1,812 2,062 2,344
82,5 94,5 94,5 141,1 209,6 141,1 255,4 355,3 187,1 442,1 547,7 640,0 720,2 808,2
26 26,00 0,312 0,500 0,375 0,500
127,4 202,7 152,9 202,7
28 28,00 0,312 0,500 0,625 0,375 0,500
137,2 218,7 271,2 164,9 218,7
30 30,00 0,250 0,312 0,312 0,500 0,625 0,375 0,500
118,3 147,4 147,3 324,7 292,2 176,8 324,7
32 32,00 0,312 0,500 0,625 0,375 0,688 0,500
157,2 250,7 316,9 188,8 342,9 250,6
34 34,00 0,312 0,500 0,625 0,375 0,688 0,500
167,2 266,6 332,1 200,3 365,0 266,6
36 36,00 0,312 0,500 0,625 0,375 0,750 0,500
177,0 282,3 351,7 212,6 420,4 282,3
IDE
NT
ICA
L to
5 s ID
EN
TIC
AL
to 1
0 s
IDE
NT
ICA
L to
40
s &
“st
d”
IDE
NT
ICA
L to
80
s &
“X
S”
ahlsell 13
PiPe schedule charT [mm]
ASME B36.19-B36.10 – pipe dimensions in mm and weights in kg
NOTE: Light blue values are wall thicknesses in mm, darker blue values are weights in kg/m. Specific steel weight used for calculation is 8.0, Titanium weight is approximately 57% of the table values, DN = Nominal Diameter - SI description of pipe size in mm,
NPS = Nominal Pipe Size - description of pipe size in inch, O.D = Outside Diameter of pipe, Sch5S and 10S do not permit threading according to ANSI B1.20.1, Sch40S and 80S in the table are applicable up to and including 12”.
DN NPS O.D. (MM) (INCH) (MM) 5 S 5 10 S 10 20 30 STD 40 60 XS 80 100 120 140 160 XXS 40 S 80 S
- 1/8 10,3 1,24 1,45 1,73 2,41
0,3 0,3 0,4 0,5
- 1/4 13,7 1,65 1,85 2,24 3,02
0,5 0,5 0,6 0,8
10 3/8 17,1 1,65 1,85 2,31 3,20
0,6 0,7 0,9 1,1
15 1/2 21,3 1,65 2,11 2,41 2,77 3,73 4,75 7,47
0,8 1,0 1,1 1,3 1,6 2,0 2,6
20 3/4 26,7 1,65 2,11 2,41 2,87 3,91 5,56 7,82
1,0 1,3 1,4 1,7 2,2 2,9 3,7
25 1 33,4 1,65 2,77 2,90 3,38 4,55 6,35 9,09
1,3 2,1 2,2 2,5 3,3 4,3 5,5
32 1 1⁄4 42,2 1,65 2,77 2,97 3,56 4,85 6,35 9,70
1,7 2,7 2,9 3,4 4,5 5,7 7,9
40 1 1⁄2 48,3 1,65 2,77 3,18 3,68 5,08 7,14 10,15
1,9 3,2 3,5 4,1 5,5 7,4 9,7
50 2 60,3 1,65 2,77 3,18 3,91 5,54 8,74 11,07
2,4 4,0 4,5 5,5 7,6 11,1 13,4
65 2 1⁄2 73,0 2,11 3,05 4,78 5,16 7,01 9,53 14,02
3,8 5,3 8,0 8,6 11,4 14,0 20,4
80 3 88,9 2,11 3,05 4,78 5,49 7,62 11,13 15,24
4,6 6,5 9,9 11,3 15,3 21,4 27,7
- 3 1⁄2 101,6 2,11 3,05 4,78 5,74 8,08
5,2 7,4 11,4 13,6 18,6
100 4 114,3 2,11 3,05 4,78 6,02 8,56 11,13 13,49 17,12
5,8 8,4 12,9 16,1 22,3 28,3 33,5 41,0
125 5 141,3 2,77 3,40 6,55 9,53 12,70 15,88 19,05
9,5 11,6 21,8 31,0 40,3 49,1 57,4
150 6 168,3 2,77 3,40 7,11 10,97 14,27 18,26 21,95
11,3 13,8 28,3 42,6 54,2 67,6 79,2
200 8 219,1 2,77 3,76 6,35 7,04 8,18 10,31 12,70 15,09 18,26 20,62 23,01 22,23
14,8 20,0 33,3 36,8 42,6 53,1 64,6 75,9 90,4 100,9 111,3 107,9
250 10 273,0 3,40 4,19 6,35 7,80 9,27 12,70 12,70 15,09 18,26 21,44 25,40 28,58 25,40
22,6 27,8 42,4 51,8 60,3 81,6 81,6 96,0 114,8 133,1 155,2 172,3 155,2
300 12 323,8 3,96 4,57 6,35 8,38 9,53 10,31 14,27 12,70 17,48 21,44 25,40 28,58 33,32 25,40
31,3 36,0 49,7 65,2 73,9 79,7 109,0 97,4 132,1 159,9 187,0 208,1 238,8 187,0
350 14 355,6 3,96 4,78 6,35 7,92 9,53 9,53 11,13 15,09 12,70 19,05 23,83 27,79 31,75 35,71
34,4 41,3 54,7 67,9 81,3 81,3 94,6 126,7 107,4 158,1 195,0 224,7 253,5 281,7
400 16 406,4 4,19 4,78 6,35 7,92 9,53 9,53 12,70 16,66 12,70 21,44 26,19 30,96 36,53 40,49
41,6 47,3 62,6 77,8 93,3 93,3 123,3 160,1 123,3 203,5 245,6 286,6 333,2 365,4
450 18 457 4,19 4,78 6,35 7,92 11,13 9,53 14,27 19,05 12,70 23,83 29,36 34,93 39,67 45,24
46,8 53,3 70,6 87,7 122,4 105,2 155,8 205,7 139,2 254,6 309,6 363,6 408,3 459,4
500 20 508 4,78 5,54 6,35 9,53 12,70 9,53 15,09 20,62 12,70 26,19 32,54 38,10 44,45 50,01
59,3 68,6 78,6 117,2 155,1 117,2 183,4 247,8 155,1 311,2 381,5 441,5 508,1 564,8
- 22 559 4,78 5,54 6,35 9,53 12,70 9,53 22,23 12,70 28,58 34,93 41,28 47,63 53,98
65,2 75,5 86,5 129,1 171,1 129,1 299,3 171,1 373,8 451,5 527,0 600,6 672,3
600 24 610 5,54 6,35 6,35 9,53 14,27 9,53 17,48 24,61 12,70 30,96 38,89 46,02 52,37 59,54
82,5 94,5 94,5 141,1 209,6 141,1 255,4 355,3 187,1 442,1 547,7 640,0 720,2 808,2
- 26 660 7,92 12,70 9,53 12,70
127,4 202,7 152,9 202,7
700 28 711 7,92 12,70 15,88 9,53 12,70
137,2 218,7 271,2 164,9 218,7
- 30 762 6,35 7,92 7,92 12,70 15,88 9,53 12,70
118,3 147,4 147,3 324,7 292,2 176,8 324,7
800 32 813 7,92 12,70 15,88 9,53 17,48 12,70
157,2 250,7 316,9 188,8 342,9 250,6
- 34 864 7,92 12,70 15,88 9,53 17,48 12,70
167,2 266,6 332,1 200,3 365,0 266,6
900 36 914 7,92 12,70 15,88 9,53 19,05 12,70
177,0 282,3 351,7 212,6 420,4 282,3
IDE
NT
ICA
L to
10
s
IDE
NT
ICA
L to
5 s
IDE
NT
ICA
L to
40
s &
“st
d”
IDE
NT
ICA
L to
80
s &
“X
S”
14 ahlsell
PiPes line PiPes
SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION
DIAMETER THICkNESS DIAMETER DIAMETER THICkNESS DIAMETER
IN. mm mm mm kG/M STD SCHEDULE IN. mm mm mm kG/M STD SCHEDULE
XS;XXS NO XS;XXS NO 1/8 10,3 1,73 6,8 0,4 STD 40 3 88,9 5,49 77,9 11,3 STD 40
2,41 5,5 0,5 XS 80 6,35 76,2 12,9
1/4 13,7 2,24 9,2 0,6 STD 40 7,14 74,6 14,4
3,02 7,7 0,8 XS 80 7,62 73,7 15,3 XS 80
3/8 17,1 2,31 12,5 0,8 STD 40 11,13 66,6 21,4 160
3,20 10,7 1,1 XS 80 15,24 58,4 27,7 XXS
1/2 21,3 2,77 15,8 1,3 STD 40 3 1⁄2 101,6 2,11 97,4 5,2 5
3,73 13,8 1,6 XS 80 2,77 96,1 6,8
4,78 11,7 2,0 160 3,05 95,5 7,4 10
7,47 6,4 2,6 XXS 3,18 95,3 7,7
3/4 26,7 2,87 21,0 1,7 STD 40 3,58 94,4 8,7
3,91 18,9 2,2 XS 80 3,96 93,7 9,5
5,56 15,6 2,9 160 4,37 92,9 10,5
7,82 11,1 3,6 XXS 4,78 92,0 11,4 30
1 33,4 3,38 26,6 2,5 STD 40 5,74 90,1 13,6 STD 40
4,55 24,3 3,2 XS 80 6,35 88,9 14,9
6,35 20,7 4,2 160 7,14 87,3 16,6
9,09 15,2 5,5 XXS 8,08 85,4 18,6 XS 80
1 1⁄4 42,2 3,56 35,1 3,4 STD 40 4 114,3 2,11 110,1 5,8 5
4,85 32,5 4,5 XS 80 2,77 108,8 7,6
6,35 29,5 5,6 160 3,05 108,2 8,4 10
9,70 22,8 7,8 XXS 3,18 108,0 8,7
1 1⁄2 48,3 3,68 40,9 4,1 STD 40 3,58 107,1 9,8
5,08 38,1 5,4 XS 80 3,96 106,4 10,8
7,14 34,0 7,3 160 4,37 105,6 11,9
10,15 28,0 9,6 XXS 4,78 104,7 12,9 30
2 60,3 1,65 57,0 2,4 5 5,16 104,0 13,9
2,11 56,1 3,0 5,56 103,2 14,9
2,77 54,8 3,9 10 6,02 102,3 16,1 STD 40
3,18 53,9 4,5 30 6,35 101,6 16,9
3,58 53,1 5,0 7,14 100,0 18,9
3,91 52,5 5,4 STD 40 7,92 98,5 20,8
4,37 51,6 6,0 8,56 97,2 22,3 XS 80
4,78 50,7 6,5 11,13 92,0 28,3 120
5,54 49,2 7,5 XS 80 13,49 87,3 33,5 160
6,35 47,6 8,5 17,12 80,1 41,0 XXS
7,14 46,0 9,4 5 141,3 2,11 137,1 7,2
8,74 42,8 11,1 160 2,77 135,8 9,5 5
11,07 38,2 13,4 XXS 3,18 135,0 10,8
2 1⁄2 73,0 2,11 68,8 3,7 5 3,40 134,5 11,6 10
2,77 67,5 4,8 3,96 133,4 13,4
3,05 66,9 5,3 10 4,78 131,7 16,1
3,18 66,7 5,5 5,56 130,2 18,6
3,58 65,8 6,1 6,55 128,2 21,8 STD 40
3,96 65,1 6,7 7,14 127,0 23,6
4,37 64,3 7,4 7,92 125,5 26,1
4,78 63,4 8,0 30 8,74 123,8 28,6
5,16 62,7 8,6 STD 40 9,53 122,3 31,0 XS 80
5,49 62,0 9,1 12,70 115,9 40,3 120
6,35 60,3 10,4 15,88 109,6 49,1 160
7,01 59,0 11,4 XS 80 19,05 103,2 57,4 XXS
9,53 54,0 14,9 160 6 168,3 2,11 164,1 8,7
14,02 45,0 20,4 XXS 2,77 162,8 11,3 5
3 88,9 2,11 84,7 4,5 5 3,18 162,0 13,0
2,77 83,4 5,9 3,40 161,5 13,8 10
3,05 82,8 6,5 10 3,58 161,1 14,5
3,18 82,6 6,7 3,96 160,4 16,1
3,58 81,7 7,5 4,37 159,6 17,7
3,96 81,0 8,3 4,78 158,7 19,3
4,37 80,2 9,1 5,16 158,0 20,8
4,78 79,3 9,9 30 5,56 157,2 22,3
ASME B 36.10 DIMENSIONS
ahlsell 15
line PiPes PIPes
SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION
DIAMETER THICkNESS DIAMETER DIAMETER THICkNESS DIAMETER
IN. mm mm mm kG/M STD SCHEDULE IN. mm mm mm kG/M STD SCHEDULE
XS;XXS NO XS;XXS NO
6 168,3 6,35 155,6 25,4 12 323,8 3,96 315,9 31,3 5
7,11 154,1 28,3 STD 40 4,37 315,1 34,4
7,92 152,5 31,3 4,57 314,7 36,0 10
8,74 150,8 34,4 4,78 314,2 37,6
9,53 149,3 37,3 5,16 313,5 40,6
10,97 146,4 42,6 XS 80 5,56 312,7 43,7
12,70 142,9 48,7 6,35 311,1 49,7 20
14,27 139,8 54,2 120 7,14 309,5 55,8
15,88 136,6 59,7 7,92 308,0 61,7
18,26 131,8 67,6 160 8,38 307,0 65,2 30
19,05 130,2 70,1 8,74 306,3 67,9
21,95 124,4 79,2 XXS 9,53 304,7 73,9 STD
22,23 123,8 80,1 10,31 303,2 79,7 40
8 219,1 2,77 213,6 14,8 5 11,13 301,5 85,8
3,18 212,8 16,9 12,70 298,4 97,5 XS
3,76 211,6 20,0 10 14,27 295,3 109,0 60
3,96 211,2 21,0 15,88 292,1 120,6
4,78 209,5 25,3 17,48 288,8 132,1 80
5,16 208,8 27,2 19,05 285,7 143,2
5,56 208,0 29,3 20,62 282,6 154,2
6,35 206,4 33,3 20 21,44 280,9 159,9 100
7,04 205,0 36,8 30 22,23 279,4 165,4
7,92 203,3 41,2 23,83 276,1 176,3
8,18 202,7 42,6 STD 40 25,40 273,0 187,0 XXS 120
8,74 201,6 45,3 26,97 269,9 197,5
9,53 200,1 49,3 28,58 266,7 208,1 140
10,31 198,5 53,1 60 31,75 260,3 228,7
11,13 196,8 57,1 33,32 257,2 238,8 160
12,70 193,7 64,6 XS 80 14 355,6 3,96 347,7 34,4 5
14,27 190,6 72,1 4,78 346,0 41,4
15,09 188,9 75,9 100 5,16 345,3 44,6
15,88 187,4 79,6 5,33 344,9 46,0
18,26 182,6 90,4 120 5,56 344,5 48,0
19,05 181,0 94,0 6,35 342,9 54,7 10
20,62 177,9 100,9 140 7,14 341,3 61,4
22,23 174,7 107,9 XXS 7,92 339,8 67,9 20
23,01 173,1 111,3 160 8,74 338,1 74,8
25,40 168,3 121,3 9,53 336,6 81,3 STD 30
10 273,0 3,40 266,2 22,6 5 10,31 335,0 87,8
3,96 265,1 26,3 11,13 333,3 94,6 40
4,19 264,6 27,8 10 11,91 331,8 100,9
4,78 263,4 31,6 12,70 330,2 107,4 XS
5,16 262,7 34,1 14,27 327,1 120,1
5,56 261,9 36,7 15,09 325,4 126,7 60
6,35 260,3 41,8 20 15,88 323,9 133,0
7,09 258,8 46,5 17,48 320,6 145,8
7,80 257,4 51,0 30 19,05 317,5 158,1 80
8,74 255,5 57,0 20,62 314,4 170,3
9,27 254,5 60,3 STD 40 22,23 311,2 182,8
11,13 250,7 71,9 23,83 307,9 195,0 100
12,70 247,6 81,6 XS 60 25,40 304,8 206,8
14,27 244,5 91,1 26,97 301,7 218,6
15,09 242,8 96,0 80 27,79 300,0 224,7 120
15,88 241,3 100,7 28,58 298,4 230,5
18,26 236,5 114,8 100 31,75 292,1 253,6 140
20,62 231,8 128,4 35,71 284,2 281,7 160
21,44 230,1 133,1 120 50,80 254,0 381,8
22,23 228,5 137,5 53,98 247,7 401,5
23,83 225,3 146,5 55,88 243,8 413,0
25,40 222,2 155,2 XXS 140 63,50 228,6 457,4
28,58 215,9 172,3 160
31,75 209,5 189,0
ASME B 36.10 DIMENSIONS
16 ahlsell
PiPes line PiPes
SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION
DIAMETER THICkNESS DIAMETER DIAMETER THICkNESS DIAMETER
IN. mm mm mm kG/M STD SCHEDULE IN. mm mm mm kG/M STD SCHEDULE
XS;XXS NO XS;XXS NO
16 406,4 4,19 398,0 41,6 5 20 508 4,78 498,4 59,3 5
4,78 396,8 47,3 5,56 496,9 68,9
5,16 396,1 51,1 6,35 495,3 78,6 10
5,56 395,3 55,0 7,14 493,7 88,2
6,35 393,7 62,6 10 7,92 492,2 97,7
7,14 392,1 70,3 8,74 490,5 107,6
7,92 390,6 77,8 20 9,53 489,0 117,2 STD 20
8,74 388,9 85,7 10,31 487,4 126,5
9,53 387,4 93,3 STD 30 11,13 485,7 136,4
10,31 385,8 100,7 11,91 484,2 145,7
11,13 384,1 108,5 12,70 482,6 155,1 XS 30
11,91 382,6 115,9 14,27 479,5 173,7
12,70 381,0 123,3 XS 40 15,09 477,8 183,4 40
14,27 377,9 138,0 15,88 476,3 192,7
15,88 374,7 152,9 17,48 473,0 211,4
16,66 373,1 160,1 60 19,05 469,9 229,7
17,48 371,4 167,7 20,62 466,8 247,8 60
19,05 368,3 182,0 22,23 463,6 266,3
20,62 365,2 196,2 23,83 460,3 284,5
21,44 363,5 203,5 80 25,40 457,2 302,3
22,23 362,0 210,6 26,19 455,6 311,2 80
23,83 358,7 224,8 26,97 454,1 319,9
25,40 355,6 238,6 28,58 450,9 337,9
26,19 354,0 245,6 100 30,18 447,7 355,6
26,97 352,5 252,4 31,75 444,5 372,9
28,58 349,3 266,3 32,54 442,9 381,5 100
30,18 346,0 280,0 33,32 441,4 390,0
30,96 344,5 286,6 120 34,93 438,2 407,5
31,75 342,9 293,3 38,10 431,8 441,5 120
36,53 333,3 333,2 140 44,45 419,1 508,1 140
40,49 325,4 365,4 160 50,01 408,0 564,8 160
18 457 4,19 448,6 46,8 5 22 559 4,78 549,4 65,2 5
4,78 447,4 53,3 5,56 547,9 75,9
5,56 445,9 61,9 6,35 546,3 86,5 10
6,35 444,3 70,6 10 7,14 544,7 97,2
7,14 442,7 79,2 7,92 543,2 107,6
7,92 441,2 87,8 20 8,74 541,5 118,6
8,74 439,5 96,6 9,53 540,0 129,1 STD 20
9,53 438,0 105,2 STD 10,31 538,4 139,5
10,31 436,4 113,6 11,13 536,7 150,4
11,13 434,7 122,4 30 11,91 535,2 160,7
11,91 433,2 130,7 12,70 533,6 171,1 XS 30
12,70 431,6 139,2 XS 14,27 530,5 191,7
14,27 428,5 155,8 40 15,88 527,3 212,7
15,88 425,3 172,7 17,48 524,0 233,4
17,48 422,0 189,5 19,05 520,9 253,7
19,05 418,9 205,7 60 20,62 517,8 273,8
20,62 415,8 221,9 22,23 514,6 294,3 60
22,23 412,6 238,3 23,83 511,3 314,5
23,83 409,3 254,6 80 25,40 508,2 334,2
25,40 406,2 270,3 26,97 505,1 353,8
26,97 403,1 286,0 28,58 501,9 373,8 80
28,58 399,9 301,9 30,18 498,6 393,6
29,36 398,3 309,6 100 31,75 495,5 412,8
30,18 396,7 317,7 33,32 492,4 431,9
31,75 393,5 333,0 34,93 489,2 451,4 100
34,93 387,2 363,6 120 36,53 485,9 470,7
39,67 377,7 408,3 140 38,10 482,8 489,4
45,24 366,5 459,4 160 41,28 476,5 527,0 120
47,63 463,8 600,6 140
53,98 451,1 672,3 160
ASME B 36.10 DIMENSIONS
ahlsell 17
line PiPes PIPes
SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION
DIAMETER THICkNESS DIAMETER DIAMETER THICkNESS DIAMETER
IN. mm mm mm kG/M STD SCHEDULE IN. mm mm mm kG/M STD SCHEDULE
XS;XXS NO XS;XXS NO
24 610 5,54 599,0 82,5 5 28 711 19,05 672,9 325,1
6,35 597,3 94,5 10 20,62 669,8 351,1
7,14 595,7 106,2 22,23 666,6 377,6
7,92 594,2 117,6 23,83 663,3 403,8
8,74 592,5 129,6 25,40 660,2 429,4
9,53 591,0 141,1 STD 20 30 762 6,35 749,3 118,3 5
10,31 589,4 152,5 7,14 747,7 132,9
11,13 587,7 164,4 7,92 746,2 147,3 10
11,91 586,2 175,7 8,74 744,5 162,4
12,70 584,6 187,1 XS 9,53 743,0 176,8 STD
14,27 581,5 209,6 30 10,31 741,4 191,1
15,88 578,3 232,7 11,13 739,7 206,1
17,48 575,0 255,4 40 11,91 738,2 220,3
19,05 571,9 277,6 12,70 736,6 234,7 XS 20
20,62 568,8 299,7 14,27 733,5 263,1
22,23 565,6 322,2 15,88 730,3 292,2 30
23,83 562,3 344,5 17,48 727,0 320,9
24,61 560,8 355,3 60 19,05 723,9 394,0
25,40 559,2 366,2 20,62 720,8 377,0
26,97 556,1 387,8 22,23 717,6 405,5
28,58 552,9 409,8 23,83 714,3 433,8
30,18 549,6 431,5 25,40 711,2 461,4
30,96 548,1 442,1 26,97 708,1 488,9
31,75 546,5 452,7 80 28,58 704,8 516,9
33,32 543,4 473,8 30,18 701,6 544,7
34,93 540,2 495,4 31,75 698,5 571,8
36,50 537,0 516,8 32 813 6,35 800,3 126,3
38,10 533,8 537,3 7,14 798,7 141,9
38,89 532,2 547,7 100 7,92 797,2 157,2 10
39,67 530,7 557,4 8,74 795,5 173,3
46,02 518,0 640,0 120 9,53 794,0 188,8 STD
52,37 505,3 720,2 140 10,31 792,4 204,1
59,54 490,9 808,2 160 11,13 790,7 220,1
26 660 6,35 647,3 102,4 11,91 789,2 235,3
7,14 645,7 115,0 12,70 787,6 250,6 XS 20
7,92 644,2 127,4 10 14,27 784,5 281,1
8,74 642,5 140,4 15,88 781,3 312,2 30
9,53 641,0 152,9 STD 17,48 778,0 342,9 40
10,31 639,4 165,2 19,05 774,9 373,0
11,13 637,7 178,1 20,62 771,8 402,9
11,91 636,2 190,3 22,23 768,6 433,5
12,70 634,6 202,7 XS 20 23,83 765,3 463,8
14,27 631,5 227,2 25,40 762,2 493,3
15,88 628,3 252,2 26,97 759,1 522,8
17,48 625,0 277,0 28,58 755,8 552,9
19,05 621,9 301,1 30,18 752,6 582,6
20,62 618,8 325,1 31,75 794,5 611,7
22,23 615,6 349,6 34 864 6,35 851,3 134,3
23,83 612,3 373,8 7,14 849,7 150,9
25,40 609,2 397,5 7,92 848,2 167,2 10
28 711 6,35 698,3 110,3 8,74 846,5 184,3
7,14 696,7 123,9 9,53 845,0 200,3 STD
7,92 695,2 137,3 10 10,31 843,4 217,1
8,74 693,5 151,4 11,13 841,7 234,1
9,53 692,0 164,9 STD 11,91 840,2 250,3
10,31 690,4 178,2 12,70 838,6 266,6 XS 20
11,13 688,7 192,1 14,27 835,5 299,0
11,91 687,2 205,3 15,88 832,3 332,1 30
12,70 685,6 218,7 XS 20 17,48 829,0 364,9 40
14,27 682,5 245,2 19,05 825,9 396,9
15,88 679,3 271,2 30 20,62 822,8 428,9
17,48 676,0 299,0 22,23 819,6 461,5
ASME B 36.10 DIMENSIONS
18 ahlsell
PiPes line PiPes
SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION SIzE OUTSIDE WALL INNER WEIGHT IDENTIFICATION
DIAMETER THICkNESS DIAMETER DIAMETER THICkNESS DIAMETER
IN. mm mm mm kG/M STD SCHEDULE IN. mm mm mm kG/M STD SCHEDULE
XS;XXS NO XS;XXS NO
34 864 23,83 816,3 493,7 42 1067 8,74 1049,6 228
25,40 813,2 525,3 9,53 1048,0 248
26,97 810,1 556,7 10,31 1046,4 269
28,58 806,8 588,8 11,13 1044,8 290
30,18 803,6 620,6 11,91 1043,2 310
31,75 800,5 651,6 12,70 1041,6 330
36 914 6,35 901,3 142,1 14,27 1038,4 370
7,14 899,7 159,7 15,88 1035,2 411
7,92 898,2 177,0 10 17,48 1032,0 452
8,74 896,5 195,1 19,05 1029,0 492
9,53 895,0 212,6 STD 20,62 1025,8 532
10,31 893,4 229,8 22,23 1022,6 572
11,13 891,7 247,3 23,83 1019,4 615
11,91 890,2 264,9 25,40 1016,2 652
12,70 888,6 282,3 XS 20 44 1168 8,74 1150,6 239
14,27 885,5 316,1 9,53 1149,0 260
15,88 882,3 351,7 30 10,31 1147,4 282
17,48 879,0 386,5 11,13 1145,8 304
19,05 875,9 420,4 40 11,91 1144,2 325
20,62 872,8 454,3 12,70 1142,6 346
22,23 869,6 488,9 14,27 1139,4 388
23,83 866,3 523,1 15,88 1136,2 431
25,40 863,2 556,6 17,48 1133,0 474
26,97 860,1 590,0 19,05 1130,0 516
28,58 856,8 624,0 20,62 1126,8 558
30,18 853,6 657,8 22,23 1123,6 600
31,75 850,5 690,8 23,83 1120,4 643
38 965 7,92 949,1 186,9 25,40 1117,2 684
8,74 947,5 206,1 46 1158 8,74 1140,6 250
9,53 945,9 224,5 9,53 1139,0 272
10,31 944,4 242,7 10,31 1137,4 294
11,13 942,7 261,8 11,13 1135,8 317
11,91 941,2 279,9 11,91 1134,2 340
12,70 939,6 298,2 12,70 1132,6 362
14,27 936,5 334,6 14,27 1129,4 406
15,88 933,2 371,7 15,88 1126,2 451
17,48 930,0 408,4 17,48 1123,0 496
19,05 926,9 444,4 19,05 1120,0 540
20,62 923,8 480,2 20,62 1116,8 584
22,23 920,5 516,8 22,23 1113,6 628
23,83 917,3 553,1 23,83 1110,4 672
25,40 914,2 588,5 25,40 1107,2 716
40 1016 7,92 1000,2 196,9 48 1219 8,74 1201,6 261
8,74 998,5 217,1 9,53 1200,0 284
9,53 996,9 236,5 10,31 1198,4 307
10,31 995,4 255,7 11,13 1196,8 331
11,13 993,7 275,8 11,91 1195,2 355
11,91 992,2 294,8 12,70 1193,6 378
12,70 990,6 314,2 14,27 1190,4 424
14,27 987,5 352,5 15,88 1187,2 471
15,88 984,2 391,7 17,48 1184,0 518
17,48 981,0 430,4 19,05 1181,0 564
19,05 977,9 468,3 20,62 1177,8 610
20,62 974,8 506,1 22,23 1174,6 656
22,23 971,5 544,8 23,83 1171,4 702
23,83 968,3 583,1 25,40 1168,2 748
25,40 965,2 620,5
NOTE: Complete range of wall thicknesses from ASME B36.10 are icluded for 2” - 36” pipe sizes. Other dimensions are only including a range of dimensions/wall thicknesses from ASME B36.10.
ASME B 36.10 DIMENSIONS
ahlsell 19
20 ahlsell
TU
BE
STuBesAsTM A269AsTM A789
ahlsell 21
22 ahlsell
TuBing meTric sizes & Pressure in Bar
FACTOR CHART FOR PRESSURE CALCULATION OF TUBING - METRIC
The below table values are based on ASME B31.3 section 304, and may be used for calculation of: 1) Working pressure (maximum allowable by design standard), i.e.”Table factor” multiplied by “Maximum Allowable Stress” (MPa) 2) Yield pressure (calculated by nominal values), i.e. “Table factor” multiplied by “Minimum Yield Strength” (MPa) 3) Burst pressure (calculated by nominal values), i.e. “Table factor” multiplied by “Minimum Tensile Strength” (MPa)
NOTE: Factors below heavy black line are calculated to ASME B31.3 section 304 using the Y=0.4, while the right factors are calculated by using Y=d/(d+D).
TUBE WALL THICkNESS (mm) TUBE O.D. (mm) 1 1,2 1,5 1,6 1,8 2 2,2 2,5 3
3 0,8000 4 0,6000 0,7241 6 0,3846 0,4706 0,6000 0,6423 8 0,2778 0,3409 0,4382 0,4706 10 0,2174 0,2655 0,3409 0,3670 0,4188 0,4706 12 0,1786 0,2174 0,2778 0,2985 0,3409 0,3846 14 0,1515 0,1840 0,2344 0,2516 0,2866 0,3226 0,3595 0,4152 0,5077 16 0,1316 0,1596 0,2027 0,2174 0,2473 0,2778 0,3090 0,3571 0,4382 18 0,1163 0,1408 0,1786 0,1914 0,2174 0,2439 0,2709 0,3125 0,3846 20 0,1042 0,1261 0,1596 0,1709 0,1940 0,2174 0,2412 0,2778 0,3409 22 0,0943 0,1141 0,1442 0,1544 0,1751 0,1961 0,2174 0,2500 0,3061 25 0,0826 0,0998 0,1261 0,1349 0,1528 0,1709 0,1893 0,2174 0,2655 28 0,0735 0,0888 0,1119 0,1198 0,1355 0,1515 0,1677 0,1923 0,2344 30 0,0685 0,0826 0,1042 0,1114 0,1261 0,1408 0,1558 0,1786 0,2174 38 0,0538 0,0648 0,0815 0,0871 0,0985 0,1099 0,1214 0,1389 0,1685
WORkING PRESSURE FOR SEAMLESS ASTM A269 316/ 316L (BAR) Allowable stress = 129MPa between -29 degree C and 38 degree C, based on: ASTM A213 - minimum yield 205MPa and min. tensile strength 515MPa Safety factor = 4 - for 515MPa
NOTE: The above pressures should only be used for guidance - as applicable codes, design standards and allowable stresses may result in other values.
TUBE WALL THICkNESS (mm) TUBE O.D. (mm) 1 1,2 1,5 1,6 1,8 2 2,2 2,5 3
3 1032 4 774 934 6 496 607 774 829 8 358 440 565 607 10 280 342 440 473 540 607 12 230 280 358 385 440 496 14 195 237 302 325 370 416 464 536 655 16 170 206 261 280 319 358 399 461 565 18 150 182 230 247 280 315 350 403 496 20 134 163 206 221 250 280 311 358 440 22 122 147 186 199 226 253 280 323 395 25 107 129 163 174 197 221 244 280 342 28 95 114 144 154 175 195 216 248 302 30 88 107 134 144 163 182 201 230 280 38 69 84 105 112 127 142 157 179 217
ahlsell 23
meTric sizes & Pressure in Bar TuBing
WORkING PRESSURE FOR SEAMLESS ASTM A269 6MO - UNS S31254 (BAR) Allowable stress = 169 MPa between -29 degree C and 93 degree C, based on: ASTM A249 - minimum yield 310MPa and min. tensile strength 675MPa. Safety factor = 4 - for 675MPa
NOTE: The above pressures should only be used for guidance - as applicable codes, design standards and allowable stresses may result in other values.
TUBE WALL THICkNESS (mm) TUBE O.D. (mm) 1 1,2 1,5 1,6 1,8 2 2,2 2,5 3
3 1352 4 1014 1224 6 650 795 1014 1086 8 469 576 741 795 10 367 449 576 620 708 795 12 302 367 469 504 576 650 14 256 311 396 425 484 545 608 702 858 16 222 270 343 367 418 469 522 604 741 18 197 238 302 323 367 412 458 528 650 20 176 213 270 289 328 367 408 469 576 22 159 193 244 261 296 331 367 423 517 25 140 169 213 228 258 289 320 367 449 28 124 150 189 202 229 256 283 325 396 30 116 140 176 188 213 238 263 302 367 38 91 110 138 147 166 186 205 235 285
WORkING PRESSURE FOR SEAMLESS 22CR DUPLEX - UNS S31803 (BAR) Allowable stress =155 MPa between -29 degree C and 38 degree C, based on: ASTM A789 - minimum yield 450MPa and min. tensile strength 620MPa.Safety factor = 4 - for 620MPa
NOTE: The above pressures should only be used for guidance - as applicable codes, design standards and allowable stresses may result in other values.
TUBE WALL THICkNESS (mm) TUBE O.D. (mm) 1 1,2 1,5 1,6 1,8 2 2,2 2,5 3
3 1240 4 930 1122 6 596 729 930 996 8 431 528 679 729 10 337 412 528 569 649 729 12 277 337 431 463 528 596 14 235 285 363 390 444 500 557 644 787 16 204 247 314 337 383 431 479 554 679 18 180 218 277 297 337 378 420 484 596 20 161 195 247 265 301 337 374 431 528 22 146 177 224 239 271 304 337 388 474 25 128 155 195 209 237 265 293 337 412 28 114 138 174 186 210 235 260 298 363 30 106 128 161 173 195 218 242 277 337 38 83 100 126 135 153 170 188 215 261
24 ahlsell
NOTE: The above pressures should only be used for guidance - as applicable codes, design standards and allowable stresses may result in other values.
TUBE WALL THICkNESS (INCHES) TUBE TUBE O.D. OD (MM.) (IN.) (Info only) 0,028 0,035 0,049 0,065 0,083 0,095 0,109 0,120 0,134 0,148 0,156
1/8 3,18 9992 12668
3/16 4,76 6360 8176 11791
1/4 6,35 4613 5912 8629 11728
5/16 7,94 3619 4613 6723 9213
3/8 9,53 2978 3782 5472 7532 9862
1/2 12,70 2198 2781 3988 5441 7178 8338
5/8 15,88 2198 3137 4254 5572 6489 7583
3/4 19,05 1818 2585 3492 4553 5286 6167 6881
7/8 22,23 1550 2198 2962 3849 4459 5188 5777 6545
1 25,40 1350 1912 2571 3334 3856 4478 4978 5628
1 1⁄4 31,75 2035 2630 3034 3515 3899 4397 4905 5199
1 1⁄2 38,10 2171 2502 2893 3205 3608 4017 4254
2 50,80 1852 2137 2363 2655 2950 3120
TuBing FracTional sizes & Pressure in Psi
FACTOR CHART FOR PRESSURE CALCULATION OF TUBING - FRACTIONAL
The below table values are based on ASME B31.3 section 304, and may be used for calculation of:1) Working pressure (maximum allowable by design standard), i.e. “Table factor” multiplied by “Maximum Allowable Stress” (MPa) 2) Yield pressure (calculated by nominal values), i.e. “Table factor” multiplied by “Minimum Yield Strength” (MPa) 3) Burst pressure (calculated by nominal values), i.e. “Table factor” multiplied by “Minimum Tensile Strength” (MPa)
WORkING PRESSURE FOR SEAMLESS ASTM A269 316/ 316L (PSI)
Allowable stress = 18750 psi between -29 degree C and 38 degree C, based on: ASTM A213 - minimum yield 205MPa and min. tensile strength 515MPa Safety factor = 4 - for 75000psi (515MPa)
NOTE: Factors below heavy black line are calculated to ASME B31.3 section 304 using the Y=0.4, while the right factors are calculated by using Y=d/(d+D).
TUBE WALL THICkNESS (INCHES) TUBE TUBE O.D. OD (MM.) (IN.) (Info only) 0,028 0,035 0,049 0,065 0,083 0,095 0,109 0,120 0,134 0,148 0,156
1/8 3,18 0,5329 0,6756
3/16 4,76 0,3392 0,4360 0,6289
1/4 6,35 0,2460 0,3153 0,4602 0,6255
5/16 7,94 0,1930 0,2460 0,3586 0,4914
3/8 9,53 0,1588 0,2017 0,2918 0,4017 0,5260
1/2 12,70 0,1173 0,1483 0,2127 0,2902 0,3828 0,4447
5/8 15,88 0,1173 0,1673 0,2269 0,2972 0,3461 0,4044
3/4 19,05 0,0970 0,1379 0,1862 0,2428 0,2819 0,3289 0,3670
7/8 22,23 0,0826 0,1173 0,1580 0,2053 0,2378 0,2767 0,3081 0,3490
1 25,40 0,0720 0,1020 0,1371 0,1778 0,2056 0,2388 0,2655 0,3002
1 1⁄4 31,75 0,1085 0,1403 0,1618 0,1875 0,2080 0,2345 0,2616 0,2773
1 1⁄2 38,10 0,1158 0,1334 0,1543 0,1709 0,1924 0,2142 0,2269
2 50,80 0,0988 0,1140 0,1261 0,1416 0,1573 0,1664
ahlsell 25
FracTional sizes & Pressure in Psi TuBing
WORkING PRESSURE FOR SEAMLESS 22CR DUPLEX - UNS S31803 (PSI) Allowable stress = 22500 psi between -29 degree C and 38 degree C, based on: ASTM A789 - minimum yield 450MPa and min. tensile strength 620MPa. Safety factor = 4 - for 90000psi (620MPa)
NOTE: The above pressures should only be used for guidance - as applicable codes, design standards and allowable stresses may result In other values.
TUBE WALL THICkNESS (INCHES) TUBE TUBE O.D. OD (MM.) (IN.) (Info only) 0,028 0,035 0,049 0,065 0,083 0,095 0,109 0,120 0,134 0,148 0,156
1/8 3,18 11991 15201
3/16 4,76 7632 9811 14150
1/4 6,35 5536 7095 10355 14073
5/16 7,94 4343 5536 8068 11056
3/8 9,53 3573 4539 6566 9038 11835
1/2 12,70 2638 3337 4785 6529 8614 10005
5/8 15,88 2638 3764 5105 6686 7787 9100
3/4 19,05 2181 3102 4191 5464 6343 7400 8257
7/8 22,23 1860 2638 3554 4619 5350 6226 6932 7854
1 25,40 1620 2295 3085 4001 4627 5374 5973 6754
1 1⁄4 31,75 2442 3156 3641 4218 4679 5277 5885 6239
1 1⁄2 38,10 2605 3002 3472 3846 4329 4820 5105
2 50,80 2222 2564 2836 3186 3540 3744
WORkING PRESSURE FOR SEAMLESS ASTM A269 6MO - UNS S31254 (PSI) Allowable stress = 24500 psi between -29 degree C and 93 degree C, based on: ASTM A249 - minimum yield 310MPa and min. tensile strength 675MPa (ASTM A249) Safety factor = 4 - for 98000psi (675MPa)
NOTE: The above pressures should only be used for guidance - as applicable codes, design standards and allowable stresses may result in other values.
TUBE WALL THICkNESS (INCHES) TUBE TUBE O.D. OD (MM.) (IN.) (Info only) 0,028 0,035 0,049 0,065 0,083 0,095 0,109 0,120 0,134 0,148 0,156
1/8 3,18 13056 16552
3/16 4,76 8310 10683 15407
1/4 6,35 6028 7725 11275 15324
5/16 7,94 4729 6028 8785 12038
3/8 9,53 3891 4942 7150 9842 12887
1/2 12,70 2873 3633 5211 7109 9380 10894
5/8 15,88 2873 4099 5558 7281 8479 9909
3/4 19,05 2375 3378 4563 5949 6907 8058 8991
7/8 22,23 2025 2873 3870 5030 5826 6780 7548 8552
1 25,40 1764 2499 3360 4356 5038 5851 6504 7354
1 1⁄4 31,75 2659 3436 3965 4593 5095 5746 6409 6793
1 1⁄2 38,10 2837 3269 3780 4188 4714 5249 5558
2 50,80 2419 2792 3088 3469 3854 4076
26 ahlsell
ahlsell 27
BU
TT
-WE
LD
FITT
ING
S
BuTT-Weld FiTTings
AsMe B 16.9 mss sP-75
AsMe B 16.28
28 ahlsell
ahlsell 29
asme B16.9/ mss sP–75 BuTT-Weld FiTTings
ASME B16.9 MSS SP-75
O.D. O.D. N.B. at A B N.B. at A B Bevel (mm) (mm) Bevel (mm) (mm)
1/2 21,3 38 16 3/4 26,7 38 19 1 33,4 38 22 1 1⁄4 42,2 48 25 1 1⁄2 48,3 57 29 2 60,3 76 35 2 1⁄2 73,0 95 44 3 88,9 114 51 3 1⁄2 101,6 133 57 4 114,3 152 64 5 141,3 190 79 6 168,3 229 95 8 219,1 305 127 10 273,0 381 159 12 323,8 457 190 14 355,6 533 222 16 406,4 610 254 16 406,4 610 254 18 457,0 686 286 18 457,0 686 286 20 508,0 762 318 20 508,0 762 318 22 559,0 838 343 22 559,0 838 343 24 610,0 914 381 24 610,0 914 381 26 660,0 991 406 26 660,0 991 406 28 711,0 1067 438 28 711,0 1067 438 30 762,0 1143 470 30 762,0 1143 470 32 813,0 1219 502 32 813,0 1219 502 34 864,0 1295 533 34 864,0 1295 533 36 914,0 1372 565 36 914,0 1372 565 38 965,0 1448 600 38 965,0 1448 600 40 1016,0 1524 632 40 1016,0 1524 632 42 1067,0 1600 660 42 1067,0 1600 660 44 1118,0 1676 695 44 1118,0 1676 695 46 1168,0 1753 727 46 1168,0 1753 727 48 1219,0 1829 759 48 1219,0 1829 759
90° long radius elbow 45° long radius elbow
A
A
90°
B
B
45°
Long radius elbows
30 ahlsell
BuTT-Weld FiTTings asme B16.9/ mss sP–75
ASME B16.9 MSS SP-75
O.D. O.D. N.B. at C M N.B. at C M Bevel (mm) (mm) Bevel (mm) (mm) 1/2 21,3 25 25 3/4 26,7 29 29 1 33,4 38 38 1 1⁄4 42,2 48 48 1 1⁄2 48,3 57 57 2 60,3 64 64 2 1⁄2 73,0 76 76 3 88,9 86 86 3 1⁄2 101,6 95 95 4 114,3 105 105 5 141,3 124 124 6 168,3 143 143 8 219,1 178 178 10 273,0 216 216 12 323,8 254 254 14 355,6 279 279 16 406,4 305 305 16 406,4 305 305 18 457,0 343 343 18 457,0 343 343 20 508,0 381 381 20 508,0 381 381 22 559,0 419 419 22 559,0 419 419 24 610,0 432 432 24 610,0 432 432 26 660,0 495 495 26 660,0 495 495 28 711,0 521 521 28 711,0 521 521 30 762,0 559 559 30 762,0 559 559 32 813,0 597 597 32 813,0 597 597 34 864,0 635 635 34 864,0 635 635 36 914,0 673 673 36 914,0 673 673 38 965,0 711 711 38 965,0 711 711 40 1016,0 749 749 40 1016,0 749 749 42 1067,0 762 711 42 1067,0 762 711 44 1118,0 813 762 44 1118,0 813 762 46 1168,0 851 800 46 1168,0 851 800 48 1219,0 889 838 48 1219,0 889 838
Equal Tees
Tees
ahlsell 31
asme B16.9/ mss sP–75 BuTT-Weld FiTTings
REDUCING OUTLET TEES (dimensions in mm)
ASME B16.9 MSS SP-75
N.B. O.D. Run Outlet N.B. O.D. Run Outlet at Bevel at Bevel
Run Outlet Run Outlet C M Run Outlet Run Outlet C M
Reducing Outlet Tees
Tees
1/2 3/8 21,3 17,3 25 25 1/2 1/4 21,3 13,7 25 25 3/4 1/2 26,7 21,3 29 29 3/4 3/8 26,7 17,3 29 29 1 3/4 33,4 26,7 38 38 1 1/2 33,4 21,3 38 38 1 1⁄4 1 42,2 33,4 48 48 1 1⁄4 3/4 42,2 26,7 48 48 1 1⁄4 1/2 42,2 21,3 48 48 1 1⁄2 1 1⁄4 48,3 42,2 57 57 1 1⁄2 1 48,3 33,4 57 57 1 1⁄2 3/4 48,3 26,7 57 57 1 1⁄2 1/2 48,3 21,3 57 57 2 1 1⁄2 60,3 48,3 64 60 2 1 1⁄4 60,3 42,2 64 57 2 1 60,3 33,4 64 51 2 3/4 60,3 26,7 64 44 2 1⁄2 2 73,0 60,3 76 70 2 1⁄2 1 1⁄2 73,0 48,3 76 67 2 1⁄2 1 1⁄4 73,0 42,2 76 64 2 1⁄2 1 73,0 33,4 76 57 3 2 1⁄2 88,9 73,0 86 83 3 2 88,9 60,3 86 76 3 1 1⁄2 88,9 48,3 86 73 3 1 1⁄4 88,9 42,2 86 70 3 1⁄2 3 101,6 88,9 95 92 3 1⁄2 2 1⁄2 101,6 73,0 95 89 3 1⁄2 2 101,6 60,3 95 83 3 1⁄2 1 1⁄2 101,6 48,3 95 79
32 ahlsell
BuTT-Weld FiTTings asme B16.9/ mss sP–75
REDUCING OUTLET TEES (dimensions in mm) – continued
ASME B16.9 MSS SP-75
N.B. O.D. Run Outlet N.B. O.D. Run Outlet at Bevel at Bevel
Run Outlet Run Outlet C M Run Outlet Run Outlet C M
4 3 1⁄2 114,3 101,6 105 102 4 3 114,3 88,9 105 98 4 2 1⁄2 114,3 73,0 105 95 4 2 114,3 60,3 105 89 4 1 1⁄2 114,3 48,3 105 86 5 4 141,3 114,3 124 117 5 3 1⁄2 141,3 101,6 124 114 5 3 141,3 88,9 124 111 5 2 1⁄2 141,3 73,0 124 108 5 2 141,3 60,3 124 105 6 5 168,3 141,3 143 137 6 4 168,3 114,3 143 130 6 3 1⁄2 168,3 101,6 143 127 6 3 168,3 88,9 143 124 6 2 1⁄2 168,3 73,0 143 121 8 6 219,1 168,3 178 168 8 5 219,1 141,3 178 162 8 4 219,1 114,3 178 156 8 3 1⁄2 219,1 101,6 178 152 10 8 273,0 219,1 216 203 10 6 273,0 168,3 216 194 10 5 273,0 141,3 216 191 10 4 273,0 114,3 216 184 12 10 323,8 273,0 254 241 12 8 323,8 219,1 254 229 12 6 323,8 168,3 254 219 12 5 323,8 141,3 254 216 14 12 355,6 323,8 279 270 14 10 355,6 273,1 279 257 14 8 355,6 219,1 279 248 14 6 355,6 168,3 279 238 16 14 406,4 355,6 305 305 16 14 406,4 355,6 305 305 16 12 406,4 323,8 305 295 16 12 406,4 323,8 305 295 16 10 406,4 273,0 305 283 16 10 406,4 273,0 305 283 16 8 406,4 219,1 305 273 16 8 406,4 219,1 305 273 16 6 406,4 168,3 305 264 16 6 406,4 168,3 305 264 18 16 457 406,4 343 330 18 16 457 406,4 343 330 18 14 457 355,6 343 330 18 14 457 355,6 343 330 18 12 457 323,8 343 321 18 12 457 323,8 343 321 18 10 457 273,0 343 308 18 10 457 273,0 343 308 18 8 457 219,1 343 298 18 8 457 219,1 343 298 20 18 508 457,0 381 368 20 18 508 475,0 381 368 20 16 508 406,4 381 356 20 16 508 406,4 381 356 20 14 508 355,6 381 356 20 14 508 355,6 381 356 20 12 508 323,8 381 346 20 12 508 323,8 381 346 20 10 508 273,0 381 333 20 10 508 273,0 381 333 20 8 508 219,1 381 324 20 8 508 219,1 381 324 22 20 559 508,0 419 406 22 20 559 508,0 419 406 22 18 559 457,0 419 394 22 18 559 457,0 419 394 22 16 559 406,4 419 381 22 16 559 406,4 419 381 22 14 559 355,6 419 381 22 14 559 355,6 419 381 22 12 559 323,8 419 371 22 12 559 323,8 419 371 22 10 559 273,0 419 359 22 10 559 273,0 419 359 24 22 610 559,0 432 432 24 22 610 559,0 432 432 24 20 610 508,0 432 432 24 20 610 508,0 432 432 24 18 610 457,0 432 419 24 18 610 457,0 432 419 24 16 610 406,4 432 406 24 16 610 406,4 432 406 24 14 610 355,6 432 406 24 14 610 355,6 432 406 24 12 610 323,8 432 397 24 12 610 323,8 432 397 24 10 610 273,0 432 384 24 10 610 273,0 432 384
ahlsell 33
asme B16.9/ mss sP–75 BuTT-Weld FiTTings
REDUCING OUTLET TEES (dimensions in mm) – continued
ASME B16.9 MSS SP-75
N.B. O.D. Run Outlet N.B. O.D. Run Outlet at Bevel at Bevel
Run Outlet Run Outlet C M Run Outlet Run Outlet C M
26 24 660 610,0 495 483 26 24 660 610,0 495 483 26 22 660 559,0 495 470 26 22 660 559,0 495 470 26 20 660 508,0 495 457 26 20 660 508,0 495 457 26 18 660 457,0 495 444 26 18 660 457,0 495 444 26 16 660 406,4 495 432 26 16 660 406,4 495 432 26 14 660 355,6 495 432 26 14 660 355,6 495 432 26 12 660 323,8 495 422 26 12 660 323,8 495 422 28 26 711 660,0 521 521 28 26 711 660,0 521 521 28 24 711 610,0 521 508 28 24 711 610,0 521 508 28 22 711 559,0 521 495 28 22 711 559,0 521 495 28 20 711 508,0 521 483 28 20 711 508,0 521 483 28 18 711 457,0 521 470 28 18 711 457,0 521 470 28 16 711 406,4 521 457 28 16 711 406,4 521 457 28 14 711 355,6 521 457 28 14 711 355,6 521 457 28 12 711 323,8 521 448 28 12 711 323,8 521 448 30 28 762 711,0 559 546 30 28 762 711,0 559 546 30 26 762 660,0 559 546 30 26 762 660,0 559 546 30 24 762 610,0 559 533 30 24 762 610,0 559 533 30 22 762 559,0 559 521 30 22 762 559,0 559 521 30 20 762 508,0 559 508 30 20 762 508,0 559 508 30 18 762 457,0 559 495 30 18 762 457,0 559 495 30 16 762 406,4 559 483 30 16 762 406,4 559 483 30 14 762 355,6 559 483 30 14 762 355,6 559 483 30 12 762 323,8 559 473 30 12 762 323,8 559 473 30 10 762 273,0 559 460 30 10 762 273,0 559 460 32 30 813 762,0 597 584 32 30 813 762,0 597 584 32 28 813 711,0 597 572 32 28 813 711,0 597 572 32 26 813 660,0 597 572 32 26 813 660,0 597 572 32 24 813 610,0 597 559 32 24 813 610,0 597 559 32 22 813 559,0 597 546 32 22 813 559,0 597 546 32 20 813 508,0 597 533 32 20 813 508,0 597 533 32 18 813 457,0 597 521 32 18 813 457,0 597 521 32 16 813 406,4 597 508 32 16 813 406,4 597 508 32 14 813 355,6 597 508 32 14 813 355,6 597 508 34 32 864 813,0 635 622 34 32 864 813,0 635 622 34 30 864 762,0 635 610 34 30 864 762,0 635 610 34 28 864 711,0 635 597 34 28 864 711,0 635 597 34 26 864 660,0 635 597 34 26 864 660,0 635 597 34 24 864 610,0 635 584 34 24 864 610,0 635 584 34 22 864 559,0 635 572 34 22 864 559,0 635 572 34 20 864 508,0 635 559 34 20 864 508,0 635 559 34 18 864 457,0 635 546 34 18 864 457,0 635 546 34 16 864 406,4 635 533 34 16 864 406,4 635 533 36 34 914 864,0 673 660 36 34 914 864,0 673 660 36 32 914 813,0 673 648 36 32 914 813,0 673 648 36 30 914 762,0 673 635 36 30 914 762,0 673 635 36 28 914 711,0 673 622 36 28 914 711,0 673 622 36 26 914 660,0 673 622 36 26 914 660,0 673 622 36 24 914 610,0 673 610 36 24 914 610,0 673 610 36 22 914 559,0 673 597 36 22 914 559,0 673 597 36 20 914 508,0 673 584 36 20 914 508,0 673 584 36 18 914 457,0 673 572 36 18 914 457,0 673 572 36 16 914 406,4 673 559 36 16 914 406,4 673 559 38 36 965 914,0 711 711 38 36 965 914,0 711 711 38 34 965 864,0 711 698 38 34 965 864,0 711 698 38 32 965 813,0 711 686 38 32 965 813,0 711 686 38 30 965 762,0 711 673 38 30 965 762,0 711 673 38 28 965 711,0 711 648 38 28 965 711,0 711 648 38 26 965 660,0 711 648 38 26 965 660,0 711 648 38 24 965 610,0 711 635 38 24 965 610,0 711 635 38 22 965 559,0 711 622 38 22 965 559,0 711 622 38 20 965 508,0 711 610 38 20 965 508,0 711 610 38 18 965 457,0 711 597 38 18 965 457,0 711 597
34 ahlsell
BuTT-Weld FiTTings asme B16.9/ mss sP–75
REDUCING OUTLET TEES (dimensions in mm) – continued
ASME B16.9 MSS SP-75
N.B. O.D. Run Outlet N.B. O.D. Run Outlet at Bevel at Bevel
Run Outlet Run Outlet C M Run Outlet Run Outlet C M
40 38 1016 965 749 749 40 38 1016 965 749 749 40 36 1016 914 749 737 40 36 1016 914 749 737 40 34 1016 864 749 724 40 34 1016 864 749 724 40 32 1016 813 749 711 40 32 1016 813 749 711 40 30 1016 762 749 698 40 30 1016 762 749 698 40 28 1016 711 749 673 40 28 1016 711 749 673 40 26 1016 660 749 673 40 26 1016 660 749 673 40 24 1016 610 749 660 40 24 1016 610 749 660 40 22 1016 559 749 648 40 22 1016 559 749 648 40 20 1016 508 749 635 40 20 1016 508 749 635 40 18 1016 457 749 622 40 18 1016 457 749 622 42 40 1067 1016 762 711 42 38 1067 968 762 711 42 36 1067 914 762 711 42 36 1067 914 762 711 42 34 1067 864 762 711 42 34 1067 864 762 711 42 32 1067 813 762 711 42 32 1067 813 762 711 42 30 1067 762 762 711 42 30 1067 762 762 711 42 28 1067 711 762 698 42 28 1067 711 762 698 42 26 1067 660 762 698 42 26 1067 660 762 698 42 24 1067 610 762 660 42 24 1067 610 762 660 42 22 1067 559 762 660 42 22 1067 559 762 660 42 20 1067 508 762 660 42 20 1067 508 762 660 42 18 1067 457 762 648 42 18 1067 457 762 648 42 16 1067 406,4 762 635 42 16 1067 406,4 762 635 44 42 1118 1067 813 762 44 42 1118 1067 813 762 44 40 1118 1016 813 749 44 40 1118 1016 813 749 44 38 1118 965 813 737 44 38 1118 965 813 737 44 36 1118 914 813 724 44 36 1118 914 813 724 44 34 1118 864 813 724 44 34 1118 864 813 724 44 32 1118 813 813 711 44 32 1118 813 813 711 44 30 1118 762 813 711 44 30 1118 762 813 711 44 28 1118 711 813 698 44 28 1118 711 813 698 44 26 1118 660 813 698 44 26 1118 660 813 698 44 24 1118 610 813 698 44 24 1118 610 813 698 44 22 1118 559 813 686 44 22 1118 559 813 686 44 20 1118 508 813 686 44 20 1118 508 813 686 46 44 1168 1118 851 800 46 44 1168 1118 851 800 46 42 1168 1067 851 787 46 42 1168 1067 851 787 46 40 1168 1016 851 775 46 40 1168 1016 851 775 46 38 1168 965 851 762 46 38 1168 965 851 762 46 36 1168 914 851 762 46 36 1168 914 851 762 46 34 1168 864 851 749 46 34 1168 864 851 749 46 32 1168 813 851 749 46 32 1168 813 851 749 46 30 1168 762 851 737 46 30 1168 762 851 737 46 28 1168 711 851 737 46 28 1168 711 851 737 46 26 1168 660 851 737 46 26 1168 660 851 737 46 24 1168 610 851 724 46 24 1168 610 851 724 46 22 1168 559 851 724 46 22 1168 559 851 724 48 46 1219 1168 889 838 48 46 1219 1168 889 838 48 44 1219 1118 889 838 48 44 1219 1118 889 838 48 42 1219 1067 889 813 48 42 1219 1067 889 813 48 40 1219 1016 889 813 48 40 1219 1016 889 813 48 38 1219 965 889 813 48 38 1219 965 889 813 48 36 1219 914 889 787 48 36 1219 914 889 787 48 34 1219 864 889 787 48 34 1219 864 889 787 48 32 1219 813 889 787 48 32 1219 813 889 787 48 30 1219 762 889 762 48 30 1219 762 889 762 48 28 1219 711 889 762 48 28 1219 711 889 762 48 26 1219 660 889 762 48 26 1219 660 889 762 48 24 1219 610 889 737 48 24 1219 610 889 737 48 22 1219 559 889 737 48 22 1219 559 889 737
ahlsell 35
asme B16.9 BuTT-Weld FiTTings
ASME B16.9 O.D. N.B. at O k Bevel
1/2 21,3 76 48 3/4 26,7 76 51 1 33,4 76 56 1 1⁄4 42,2 95 70 1 1⁄2 48,3 114 83 2 60,3 152 106 2 1⁄2 73,0 190 132 3 88,9 229 159 3 1⁄2 101,6 267 184 4 114,3 305 210 5 141,3 381 262 6 168,3 457 313 8 219,1 610 414 10 273,0 762 518 12 323,8 914 619 14 355,6 1067 711 16 406,4 1219 813 18 457,0 1372 914 20 508,0 1524 1016 22 559,0 1676 1118 24 610,0 1829 1219
LONG RADIUS RETURN BENDS (dimensions in mm)
Long Radius Return Bends
Long Radius Bends
36 ahlsell
BuTT-Weld FiTTings asme B16.9/ mss sP–75
ASME B16.9 MSS SP-75
O.D. O.D. N.B. at Bevel N.B. at Bevel L.E. S.E. L.E. S.E. H L.E. S.E. L.E. S.E. H
3/4 3/8 26,7 17,3 38
3/4 1/2 26,7 21,3 38
1 3/4 33,4 26,7 51
1 1/2 33,4 21,3 51
1 1⁄4 1 42,2 33,4 51
1 1⁄4 3/4 42,2 26,7 51
1 1⁄4 1/2 42,2 21,3 51
1 1⁄2 1 1⁄4 48,3 42,2 64
1 1⁄2 1 48,3 33,4 64
1 1⁄2 3/4 48,3 26,7 64
1 1⁄2 1/2 48,3 21,3 64
2 1 1⁄2 60,3 48,3 76
2 1 1⁄4 60,3 42,2 76
2 1 60,3 33,4 76
2 3/4 60,3 26,7 76
2 1⁄2 2 73,0 60,3 89
2 1⁄2 1 1⁄2 73,0 48,3 89
2 1⁄2 1 1⁄4 73,0 42,2 89
2 1⁄2 1 73,0 33,4 89
3 2 1⁄2 88,9 73,0 89
3 2 88,9 60,3 89
3 1 1⁄2 88,9 48,3 89
3 1 1⁄4 88,9 42,2 89
3 1⁄2 3 101,6 88,9 102
3 1⁄2 2 1⁄2 101,6 73,0 102
3 1⁄2 2 101,6 60,3 102
3 1⁄2 1 1⁄2 101,6 48,3 102
3 1⁄2 1 1⁄4 101,6 42,2 102
4 3 1⁄2 114,3 101,6 102
4 3 114,3 88,9 102
4 2 1⁄2 114,3 73,0 102
4 2 114,3 60,3 102
4 1 1⁄2 114,3 48,3 102
REDUCERS (dimensions in mm)
ASME B16.9 MSS SP-75
O.D. O.D. N.B. at Bevel N.B. at Bevel L.E. S.E. L.E. S.E. H L.E. S.E. L.E. S.E. H
5 4 141,3 114,3 127
5 3 1⁄2 141,3 101,6 127
5 3 141,3 88,9 127
5 2 1⁄2 141,3 73,0 127
5 2 141,3 60,3 127
6 5 168,3 141,3 140
6 4 168,3 114,3 140
6 3 1⁄2 168,3 101,6 140
6 3 168,3 88,9 140
6 2 1⁄2 168,3 73,0 140
8 6 219,1 168,3 152
8 5 219,1 141,3 152
8 4 219,1 114,3 152
8 3 1⁄2 219,1 101,6 152
10 8 273,0 219,1 178
10 6 273,0 168,3 178
10 5 273,0 141,3 178
10 4 273,0 114,3 178
12 10 323,8 273,0 203
12 8 323,8 219,1 203
12 6 323,8 168,3 203
12 5 323,8 141,3 203
14 12 355,6 323,8 330
14 10 355,6 273,0 330
14 8 355,6 219,1 330
14 6 355,6 168,3 330
16 14 406,4 355,6 356 16 14 406,4 355,6 356
16 12 406,4 323,8 356 16 12 406,4 323,8 356
16 10 406,4 273,0 356 16 10 406,4 273,0 356
16 8 406,4 219,1 356 16 8 406,4 219,1 356
18 16 457,2 406,4 381 18 16 457,2 406,4 381
18 14 457,0 355,6 381 18 14 457,0 355,6 381
18 12 457,0 323,8 381 18 12 457,0 323,8 381
18 10 457,0 273,0 381 18 10 457,0 273,0 381
Concentric and eccentric reducers
Reducers
NOTE: LE = Large End SE = Small End
ahlsell 37
asme B16.9/ mss sP–75 BuTT-Weld FiTTings
ASME B16.9 MSS SP-75
O.D. O.D. N.B. at Bevel N.B. at Bevel L.E. S.E. L.E. S.E. H L.E. S.E. L.E. S.E. H
20 18 508 457 508 20 18 508 457 508
20 16 508 406,4 508 20 16 508 406,4 508
20 14 508 355,6 508 20 14 508 355,6 508
20 12 508 323,8 508 20 12 508 323,8 508
22 20 559 508 508 22 20 559 508 508
22 18 559 457 508 22 18 559 457 508
22 16 559 406,4 508 22 16 559 406,4 508
22 14 559 355,6 508 22 14 559 355,6 508
24 22 610 559 508 24 22 610 559 508
24 20 610 508 508 24 20 610 508 508
24 18 610 457 508 24 18 610 457 508
24 16 610 406,4 508 24 16 610 406,4 508
26 24 660 610 610 26 24 660 610 610
26 22 660 559 610 26 22 660 559 610
26 20 660 508 610 26 20 660 508 610
26 18 660 457 610 26 18 660 457 610
28 26 711 660 610 28 26 711 660 610
28 24 711 610 610 28 24 711 610 610
28 22 711 559 610
28 20 711 508 610 28 20 711 508 610
28 18 711 457 610 28 18 711 457 610
30 28 762 711 610 30 28 762 711 610
30 26 762 660 610 30 26 762 660 610
30 24 762 610 610 30 24 762 610 610
30 22 762 559 610
30 20 762 508 610 30 20 762 508 610
32 30 813 762 610 32 30 813 762 610
32 28 813 711 610 32 28 813 711 610
32 26 813 660 610 32 26 813 660 610
32 24 813 610 610 32 24 813 610 610
34 32 864 813 610 34 32 864 813 610
34 30 864 762 610 34 30 864 762 610
34 28 864 711
34 26 864 660 610 34 26 864 660 610
34 24 864 610 610 34 24 864 610 610
36 34 914 864 610 36 34 914 864 610
36 32 914 813 610 36 32 914 813 610
36 30 914 762 610 36 30 914 762 610
36 28 914 711 610
36 26 914 660 610 36 26 914 660 610
36 24 914 610 610 36 24 914 610 610
38 36 965 914 610 38 36 965 914 610
38 34 965 864 610 38 34 965 864 610
38 32 965 813 610 38 32 965 813 610
38 30 965 762 610 38 30 965 762 610
38 28 965 711 610 38 28 965 711 610
38 26 965 660 610 38 26 965 660 610
38 24 965 610 610
38 22 965 559 610
38 20 965 508 610
REDUCERS (dimensions in mm) - continued
ASME B16.9 MSS SP-75
O.D. O.D. N.B. at Bevel N.B. at Bevel L.E. S.E. L.E. S.E. H L.E. S.E. L.E. S.E. H
40 38 1016 965 610 40 38 1016 965 610
40 36 1016 914 610 40 36 1016 914 610
40 34 1016 864 610 40 34 1016 864 610
40 32 1016 813 610 40 32 1016 813 610
40 30 1016 762 610 40 30 1016 762 610
40 28 1016 711 610
40 26 1016 660 610
40 24 1016 610 610
40 22 1016 559 610
40 20 1016 508 610
42 40 1067 1016 610 42 40 1067 1016 610
42 38 1067 965 610 42 38 1067 965 610
42 36 1067 914 610 42 36 1067 914 610
42 34 1067 864 610 42 34 1067 864 610
42 32 1067 813 610 42 32 1067 813 610
42 30 1067 762 610 42 30 1067 762 610
42 28 1067 711 610
42 26 1067 660 610
42 24 1067 610 610
42 22 1067 559 610
44 42 1118 1067 610 44 42 1118 1067 610
44 40 1118 1016 610 44 40 1118 1016 610
44 38 1118 965 610 44 38 1118 965 610
44 36 1118 914 610 44 36 1118 914 610
44 34 1118 864 610
44 32 1118 813 610
44 30 1118 762 610
44 28 1118 711 610
44 26 1118 660 610
44 24 1118 610 610
44 22 1118 559 610
46 44 1168 1118 711 46 44 1168 1118 711
46 42 1168 1067 711 46 42 1168 1067 711
46 40 1168 1016 711 46 40 1168 1016 711
46 38 1168 965 711 46 38 1168 965 711
46 36 1168 914 711
46 34 1168 864 711
46 32 1168 813 711
46 30 1168 762 711
46 28 1168 711 711
46 26 1168 660 711
46 24 1168 610 711
48 46 1219 1168 711 48 46 1219 1168 711
48 44 1219 1118 711 48 44 1219 1118 711
48 42 1219 1067 711 48 42 1219 1067 711
48 40 1219 1016 711 48 40 1219 1016 711
48 38 1219 965 711
48 36 1219 914 711
48 34 1219 864 711
48 32 1219 813 711
48 30 1219 762 711
48 28 1219 711 711
48 26 1219 660 711
48 24 1219 610 711
NOTE: LE = Large End SE = Small End
38 ahlsell
BuTT-Weld FiTTings asme B16.9/ mss sP–43
ASME B16.9 - long type
O.D. RAD. DIA. O.D. of N.B. at F of of Barrel Bevel Fillet Lap R G Max. Min.
1/2 21,3 76 3 35 22,8 20,5 3/4 26,7 76 3 43 28,1 25,9 1 33,4 102 3 51 35,0 32,6 1 1⁄4 42,2 102 5 64 43,6 41,4 1 1⁄2 48,3 102 6 73 49,9 47,5 2 60,3 152 8 92 62,4 59,5 2 1⁄2 73,0 152 8 105 75,3 72,2 3 88,9 152 10 127 91,3 88,1 3 1⁄2 101,6 152 10 140 104,0 100,8 4 114,3 152 11 157 116,7 113,5 5 141,3 203 11 186 144,3 140,5 6 168,3 203 13 216 171,3 167,5 8 219,1 203 13 270 222,1 218,3 10 273,0 254 13 324 277,2 272,3 12 323,8 254 13 381 328,0 323,1 14 355,6 305 13 413 359,9 354,8 16 406,4 305 13 470 411,0 405,6 18 457,0 305 13 533 462,0 456,0 20 508,0 305 13 584 514,0 507,0 22 559,0 305 13 641 565,0 558,0 24 610,0 305 13 692 616,0 609,0
LAP-JOINT STUB ENDS (dimensions in mm)
ASME B16.9 - Short type / MSS SP 43 Type A
O.D. RAD. DIA. O.D. of N.B. at F of of Barrel Bevel Fillet Lap R G Max. Min.
1/2 21,3 51 3 35 22,8 20,5 3/4 26,7 51 3 43 28,1 25,9 1 33,4 51 3 51 35,0 32,6 11⁄4 42,2 51 5 64 43,6 41,4 11⁄2 48,3 51 6 73 49,9 47,5 2 60,3 64 8 92 62,4 59,5 21⁄2 73,0 64 8 105 75,3 72,2 3 88,9 64 10 127 91,3 88,1 31⁄2 101,6 76 10 140 104,0 100,8 4 114,3 76 11 157 116,7 113,5 5 141,3 76 11 186 144,3 140,5 6 168,3 89 13 216 171,3 167,5 8 219,1 102 13 270 222,1 218,3 10 273,0 127 13 324 277,2 272,3 12 323,8 152 13 381 328,0 323,1 14 355,6 152 13 413 359,9 354,8 16 406,4 152 13 470 411,0 405,6 18 457,0 152 13 533 462,0 456,0 20 508,0 152 13 584 514,0 507,0 22 559,0 152 13 641 565,0 558,0 24 610,0 152 13 692 616,0 609,0
When used with the higher pressure flanges, it may be necessary to increase the length of stub ends in sizes 12in and larger. Such increase in length shall be a matter of agreement between the manufacturer and purchaser.
R – These dimensions conform to the radius established for lap-joint flanges in American National Standard Steel Pipe Flanges and Flanged Fittings ANSI B16.5.G – The dimension conform to standard machined facings shown in the Americam National Standard Steel Pipe Flanges and Flanged Fittings ANSI B16.5. The back face of the lap shall be machined to conform to the surface on which it seats. Where ring joint facings are to be applied use dimension ´K´ as given in ANSI B16.5.F – When special facings such as tongoue-groove, male-female, etc. are employed, additional lap thickness must be provided and such additional thickness shall be in addition to (not included in) the basic length ´F´´.
Lap-Joint Stub Ends
Stub Ends
ahlsell 39
asme B16.9/ mss sP–75 BuTT-Weld FiTTings
END CAPS (dimensions in mm)
ASME B16.9 MSS SP-75
# Limiting 3 # Limiting O.D. at W.T. O.D. at W.T. N.B. Bevel E for E1 N.B. Bevel E for E1 Length E Length E
1/2 21,3 25 4,57 25 3/4 26,7 25 3,81 25 1 33,4 38 4,57 38 1 1⁄4 42,2 38 4,83 38 1 1⁄2 48,3 38 5,08 38 2 60,3 38 5,59 44 2 1⁄2 73,0 38 7,11 51 3 88,9 51 7,62 64 3 1⁄2 101,6 64 8,13 76 4 114,3 64 8,64 76 5 141,3 76 9,65 89 6 168,3 89 10,92 102 8 219,1 102 12,70 127 10 273,0 127 12,70 152 12 323,8 152 12,70 178 14 355,6 165 12,70 191 16 406,4 178 12,70 203 16 406,4 178 25,4 203 18 457 203 12,70 229 18 457 203 25,4 229 20 508 229 12,70 254 20 508 229 25,4 254 22 559 254 12,70 254 22 559 254 25,4 279 24 610 267 12,70 305 24 610 267 25,4 305 26 660 267 – – 26 660 267 25,4 305 28 711 267 – – 28 711 267 25,4 305 30 762 267 – – 30 762 267 25,4 305 32 813 267 – – 32 813 267 25,4 305 34 864 267 – – 34 864 267 25,4 305 36 914 267 – – 36 914 267 25,4 305 38 965 305 – – 38 965 305 25,4 343 40 1016 305 – – 40 1016 305 25,4 343 42 1067 305 – – 42 1067 305 25,4 343 44 1118 343 – – 44 1118 343 25,4 381 46 1168 343 – – 46 1168 343 25,4 381 48 1219 343 – – 48 1219 343 25,4 381
*The shape of these caps shall be ellipsoidal and shall conform to the shape requirements as given in ASME Boiler and Pressure Vessel Code. #Length E applies for thickness not exceeding that given in column “Limiting Wall Thickness for Length E”. 3 *3 Length E1, applies for thickness greater than that given in column “Limiting Wall Thickness” for sizes 24in. and smaller. For type B16.9 sizes 26in. and larger the length E1, shall be by agreement between manufacturer and purchaser.
End Caps
40 ahlsell
BuTT-Weld FiTTings asme B16.28
ASME B16.28 [mm] O.D. at Bevel - D Center to End dim. - A N.B. (inch) Min. Nom. Max. Min. Nom. Max.
1 32 33 34 23 25 27 1 1⁄4 41 42 43 30 32 34 1 1⁄2 47 48 49 36 38 40 2 59 60 61 49 51 53 2 1⁄2 72 73 74 62 64 66 3 88 89 90 74 76 78 3 1⁄2 101 102 103 87 89 91 4 113 114 116 100 102 104 5 140 141 144 125 127 129 6 167 168 171 150 152 154 8 217 219 221 201 203 205 10 270 273 277 252 254 256 12 321 324 328 302 305 308 14 353 356 360 353 356 359 16 403 406 410 403 406 409 18 454 457 461 454 457 460 20 503 508 514 505 508 511 22 554 559 565 556 559 562 24 605 610 616 607 610 613
ASME B16.28 [mm] O.D. at Center to Back to N.B. Bevel - D Center - O Bevel Face - k (inch) Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. 1 32 33 34 44 51 58 34 41 48 1 1⁄4 41 42 43 57 64 71 45 52 59 1 1⁄2 47 48 49 69 76 83 55 62 69 2 59 60 61 95 102 109 74 81 88 2 1⁄2 72 73 74 120 127 134 93 100 107 3 88 89 90 145 152 159 114 121 128 3 1⁄2 101 102 103 171 178 185 133 140 147 4 113 114 116 196 203 210 152 159 166 5 140 141 144 247 254 261 190 197 204 6 167 168 171 298 305 312 230 237 244 8 217 219 221 399 406 413 306 313 320 10 270 273 277 498 508 518 384 391 398 12 321 324 328 600 610 620 460 467 474 14 353 356 360 701 711 721 526 533 540 16 403 406 410 803 813 823 603 610 617 18 454 457 461 904 914 924 679 686 693 20 503 508 514 1006 1016 1026 755 762 769 22 554 559 565 1108 1118 1128 831 838 845 24 605 610 616 1209 1219 1229 907 914 921
Short radius elbows
Short radius 180° returns
ahlsell 41
asme B16.9 / mss sP–75 BuTT-Weld FiTTings
Welding Bevel For Fittings – MSS SP – 75 (mm)
*NOTE: Plain bevel up to t ≤ 25,4 mm at manufacturers option. Plain bevel may be 37,5o up to ≤ 24“ at manufacturers option.
* 300 + 50
- 00
*t=20 max.
1,6±0,8 1,6±0,8
20
t 20v
Bevel types
100 ± 10
37,50 ± 2,50
Rad.
Welding Bevel For Fittings – ANSI B16.9/B16.28 (mm)
1,6±0,8 1,6±0,8
100 ± 10
37,50 ± 2,50
Rad.
20
t 22,2v
37,50 ± 2,50
t max 22,2
42 ahlsell
BuTT-Weld FiTTings mss sP–75
TOLERANCE (mm) FOR MSS SP–75 All Fittings
Nominal Inside Wall Out-of-roundness Center-to-end Overall Overall Angularity Elbows Reducers Pipe Diameter Thick- Dimensions Length Length Off Angle Off Plane Off Plane Size at End ness A, B, C, M H E Q P P
At ends of fittings Throughout Body of Tees & Elbows Other Elbows 1.5R elbows 3R elbows Reducers Caps
16 to 24 ± 2.3 - 0.3 4.8 3.1 2.5% ± 2.3 ± 3.1 ± 2.3 ± 6.4 1.6 6.4 2.5%
26 to 36 ± 2.3 - 0.3 Note 5 3.1 2.5% ± 3.1 ± 6.4 ± 4.8 ± 9.7 2.3 12.7 2.5%
38 to 48 ± 3.1 - 0.3 Note 5 3.1 2.5% ± 4.8 ± 9.7 ± 9.7 ± 9.7 3.1 19.1 2.5%
NOTE: 1) The inside diameter at end shall be determined by circumferential measurements, and the tolerace refers to variations from nominal I.D. calculations by (OD nom - 2tnom). 2) Out-of-roundness tolerances shall be the difference between the maximum and minimum diameters measured on any radial cross-section. 3) Minus 0.3 mm except that isolated non-continuous reduction are permitted in accordance with subsection 13.2.1 Excess thickness whether on inside or outside is to be treated in accordance with sketch given in Figure 3. 4) When elbows are intended for field segmenting, out-of-roundness tolerance may be furnished to 1% by agreement between the manufacturer and the purchaser. It is recognized that extra thickness, if any, may be on the I.D. 5) Out-of-roundness toleraces at ends shall be 1% of diameter for NPS 26 and larger. 6) Percent of O.D.
NOTE: Outside diameter may be tapered at angle to 30o beyond weld bevel.
Tolerances
ahlsell 43
asme B16.9/ B16.28 BuTT-Weld FiTTings
TOLERANCES - ASME B16.9/B16.28
Angularity Tol. Nominal Pipe Off Off Size Angle Plane (inch) Q (mm) P (mm)
1/2 - 4 1 2 5 - 8 2 4 10 - 12 3 5 14 - 16 3 6 18 - 24 4 10 26 - 30 5 10 32 - 42 5 13 44 - 48 5 19
90-Deg Reducers and and 45-Deg Lap- All Fittings Elbows Joint Caps 180-Deg Returns Lap-Joint Ends and Stub Tees Ends
Nominal Outside* Inside Wall Centre-to Overall Overall Centre-to- Back-to-Face Alignment Outside Fillet Pipe Diameter Diameter Thick- End Length Length Centre Dimension of Ends Diameter Radius Size at Bevel at End ness Dimension Dimension of Lap of Lap (inch) (1), (2) (1), (3), (4) (3) A, B, C, M F, H E O k U G R
+1.6 +0 +0 1/2 - 2 1⁄2 -0.8 ±0.8 ±2 ±2 ±3 ±6 ±6 ±1 -1 -1 +0 +0 3 - 3 1/2 ±1.6 ±1.6 Not ±2 ±2 ±3 ±6 ±6 ±1 -1 -1 less than +0 +0 4 ±1.6 ±1.6 87.5% ±2 ±2 ±3 ±6 ±6 ±1 -1 -2 of +2.4 nominal +0 +0 5 - 8 -1.6 ±1.6 thick- ±2 ±2 ±6 ±6 ±6 ±1 -1 -2 ness +4.0 +0 +0 10 - 18 -3.2 ±3.2 ±2 ±2 ±6 ±10 ±6 ±2 -2 -2 +6.4 +0 +0 20 - 24 -4.8 ±4.8 ±2 ±2 ±6 ±10 ±6 ±2 -2 -2 +6.4 26 - 30 -4.8 ±4.8 ±3 ±5 ±10 - - - - - +6.4 32 - 48 -4.8 ±4.8 ±5 ±5 ±10 - - - - -
NOTE: 1) Out-of-round is the sum of absolute values of plus and minus tolerance. 2) This tolerance may be exceeded in localized areas of formed fittings where increased wall thicknss is required to meet design requirements of para. 2.2. 3) The inside diameter and the nominal wall thichknesses at ends are to be specified by the purchaser. 4) Unless otherwise specified by the purchaser, these tolerances apply to the nominal inside diameter, which equals the difference between the nominal outside and twice the nominal wall thickness.
44 ahlsell
MA
NIFO
LDFIT
TIN
GS
maniFold FiTTings
ahlsell 45
46 ahlsell
ahlsell 47
maniFold FiTTings
Designed to meet international standardManifold Fittings have been designed in accordance with the following standard:
MSS SP-75 Specification for High Test Wrought
Butt Weld Fittings.
ASME B31.3 Chemical Plant and Petroleum Refinery
Piping.
ASME B16.9 Factory Made Wrought Steel
Butt Weld Fittings.
NACE MR-01-75 Sulfide Stress Cracking Resistant Metallic
Material for Oilfield Equipment.
ASME VIII Division 1 Section 13.10 Boiler and Pressure
Vessel Code.
API 6A Specification for Wellhead and Christmas
Tree Equipment.
Designed in two standard product levelsManufacture provide levels of standard products to meet requirements for 5.000 psi and 10.000 psi services.
Designed for high performance
under hazardous conditionsManifold Fittings have been designed to address a number of factors wich are vital in achieving high performance in hazardous oilfield service.
Erosion and corrosIon
All fittings have wall thickness designed with ample erosion and corrosion allowance.
Weldability
Material have been selected with particular emphasis of their weldability and compability with common piping materials.
Flow characteristics
The internal bores of forged fittings are machined on sophisti-cated computer controlled machining centres to ensure smooth uninterruptet transitions from bore to bore. Flow characteristics are enchanced to their maximum potential.
Dependability
Being forged from billet in closed dies negates most, if not all, the problems with assosiated with hidden flaws Inherent in casting and plate. Throughout the working life of an Manifold Fittings you can be sure a consistently sound wall section is ever present.
Max Cold Working Pressure 5.000 psi 10.000 psiMax Test Pressure 10.000 psi 15.000 psiMax Operation Temp. 400 deg F 400 deg FMin. Operation Temp. –50 deg C –50 deg CNominal Sizes 2” to 6” 2” to 6”Min. Yield Stress 52K psi 75K psiMaterial Carbon Low Alloy Manganese Steel Steel
5.000 psi 10.000 psi
Manifold Fittings nominal dimensions in mm
Size (NB) A B C D E F G
2” 406,4 203,2 152,4 330,2 - 203,2 386,1 3” 406,4 203,2 152,4 330,2 304,8 203,2 386,1 4” 558,8 279,4 208,3 406,4 355,6 279,4 495,3 5” 609,6 304,8 241,3 482,6 406,4 292,1 586,5 6” 762 381 304,8 685,8 609,6 330,2 805,2
Full Flow Cross
Long Sweep 90° elbow
Long Sweep TEELong Sweep TEE WithTop integral bullplug
Long Sweep full flow tee Standpipe Gosseneck 160°with top outlet
Long sweep 45° elbowStandpipe gooseneck with top integral bullplug
3D elbows 90 degree and 45 degree are available double backed
48 ahlsell
FLAN
GE
SA
SM
E B
16.5
Flangesasme B16.5
ahlsell 49
50 ahlsell
PiPe Flanges asMe B16.5
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Flange dimensions HUB dimensions Length Through HUB Threaded flange SW Bore
Nominal Thr. Pipe OD Large Small Slip, Weld Counter Thread Socket Slip-On, Weld Size flange Thickn. end end Sw Lapped neck bore length depth SW Lapped neck
NPS O tf min.# X A Y Y Y Q min. T min. D B min. B min. B
1/2 90,0 9,6 30,0 21,3 14,0 16,0 46,0 . . . 16,0 10,0 22,2 22,9 15,8
3/4 100,0 11,2 38,0 26,7 14,0 16,0 51,0 . . . 16,0 11,0 27,7 28,2 20,9
1 110,0 12,7 49,0 33,4 16,0 17,0 54,0 . . . 17,0 13,0 34,5 34,9 26,6
1 1⁄4 115,0 14,3 59,0 42,2 19,0 21,0 56,0 . . . 21,0 14,0 43,2 43,7 35,1
1 1⁄2 125,0 15,9 65,0 48,3 21,0 22,0 60,0 . . . 22,0 16,0 49,5 50,0 40,9
2 150,0 17,5 78,0 60,3 24,0 25,0 62,0 . . . 25,0 17,0 61,9 62,5 52,5
2 1⁄2 180,0 20,7 90,0 73,0 27,0 29,0 68,0 . . . 29,0 19,0 74,6 75,4 62,7
3 190,0 22,3 108,0 88,9 29,0 30,0 68,0 . . . 30,0 21,0 90,7 91,4 77,9
3 1⁄2 215,0 22,3 122,0 101,6 30,0 32,0 70,0 . . . 32,0 . . . 103,4 104,1 90,1
4 230,0 22,3 135,0 114,3 32,0 33,0 75,0 . . . 33,0 . . . 116,1 116,8 102,3
5 255,0 22,3 164,0 141,3 35,0 36,0 87,0 . . . 36,0 . . . 143,8 144,4 128,2
6 280,0 23,9 192,0 168,3 38,0 40,0 87,0 . . . 40,0 . . . 170,7 171,4 154,1
8 345,0 27,0 246,0 219,1 43,0 44,0 100,0 . . . 44,0 . . . 221,5 222,2 202,7
10 405,0 28,6 305,0 273,0 48,0 49,0 100,0 . . . 49,0 . . . 276,2 277,4 254,6
12 485,0 30,2 365,0 323,8 54,0 56,0 113,0 . . . 56,0 . . . 327,0 328,2 304,8
14 535,0 33,4 400,0 355,6 56,0 79,0 125,0 . . . 57,0 . . . 359,2 360,2 To be
16 595,0 35,0 457,0 406,4 62,0 87,0 125,0 . . . 64,0 . . . 410,5 411,2 specified
18 635,0 38,1 505,0 457,0 67,0 97,0 138,0 . . . 68,0 . . . 461,8 462,3 by
20 700,0 41,3 559,0 508,0 71,0 103,0 143,0 . . . 73,0 . . . 513,1 514,4 purchaser
24 815,0 46,1 663,0 610,0 81,0 111,0 151,0 . . . 83,0 . . . 616,0 616,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B2 for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth # Lapped flange shall be 1.6 mm thicker than table value.
CLASS 150 FLANGES
DIMENSIONS OF CLASS 150 FLANGES (mm)
ahlsell 51
AsMe B16.5 PiPe Flanges
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RF dimensions RTJ dimensions Bolt hole drilling Stud bolt length
Nominal Pipe Groove Groove Groove Groove Bolt Bolt No of Bolt 2,0mm Ring Size OD Height OD Height number Pitch Depth Width Circle hole bolts diam. RF Joint
NPS R k E P E F W Bh L L
1/2 34,9 2,0 . . . . . . . . . . . . . . . . . . 60,3 15,9 4 1/2 55,0 . . . 3/4 42,9 2,0 . . . . . . . . . . . . . . . . . . 69,9 15,9 4 1/2 65,0 . . . 1 50,8 2,0 63,5 6,35 R15 47,63 6,35 8,74 79,4 15,9 4 1/2 65,0 75,0 1 1⁄4 63,5 2,0 73,0 6,35 R17 57,15 6,35 8,74 88,9 15,9 4 1/2 70,0 85,0 1 1⁄2 73,0 2,0 82,5 6,35 R19 65,07 6,35 8,74 98,4 15,9 4 1/2 70,0 85,0 2 92,1 2,0 102,0 6,35 R22 82,55 6,35 8,74 120,7 19,1 4 5/8 85,0 95,0 2 1⁄2 104,8 2,0 121,0 6,35 R25 101,60 6,35 8,74 139,7 19,1 4 5/8 90,0 100,0 3 127,0 2,0 133,0 6,35 R29 114,30 6,35 8,74 152,4 19,1 4 5/8 90,0 100,0 3 1⁄2 139,7 2,0 154,0 6,35 R33 131,78 6,35 8,74 177,8 19,1 8 5/8 90,0 100,0 4 157,2 2,0 171,0 6,35 R36 149,23 6,35 8,74 190,5 19,1 8 5/8 90,0 100,0 5 185,7 2,0 194,0 6,35 R40 171,45 6,35 8,74 215,9 22,2 8 3/4 95,0 110,0 6 215,9 2,0 219,0 6,35 R43 193,68 6,35 8,74 241,3 22,2 8 3/4 100,0 115,0 8 269,9 2,0 273,0 6,35 R48 247,65 6,35 8,74 298,5 22,2 8 3/4 110,0 120,0 10 323,8 2,0 330,0 6,35 R52 304,80 6,35 8,74 362,0 25,4 12 7/8 115,0 125,0 12 381,0 2,0 406,0 6,35 R56 381,00 6,35 8,74 431,8 25,4 12 7/8 120,0 135,0 14 412,8 2,0 425,0 6,35 R59 396,88 6,35 8,74 476,3 28,6 12 1 135,0 145,0 16 469,9 2,0 483,0 6,35 R64 454,03 6,35 8,74 539,8 28,6 16 1 135,0 145,0 18 533,4 2,0 546,0 6,35 R68 517,53 6,35 8,74 577,9 31,8 16 1 1⁄8 145,0 160,0 20 584,2 2,0 597,0 6,35 R72 558,80 6,35 8,74 635,0 31,8 20 1 1⁄8 160,0 170,0 24 692,2 2,0 711,0 6,35 R76 673,10 6,35 8,74 749,3 34,9 20 1 1⁄4 170,0 185,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B2 for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth
CLASS 150 FLANGES
DIMENSIONS OF CLASS 150 FLANGES (mm)
WR
O
k min.
P
52 ahlsell
PiPe Flanges asMe B16.5
CLASS 300 FLANGES
DIMENSIONS OF CLASS 300 FLANGES (mm)
To be
specified
by
purchaser
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Flange dimensions HUB dimensions Length Through HUB Threaded flange SW Bore
Nominal Thr. Pipe OD Large Small Slip, Weld Counter Thread Socket Slip-On, Weld Size flange Thickn. end end Sw. Lapped neck bore length depth SW Lapped neck
NPS O tf min.# X A Y Y Y Q min. T min. D B min. B min. B
1/2 95,0 12,7 38,0 21,3 21,0 22,0 51,0 23,6 16,0 10,0 22,2 22,9 15,8
3/4 115,0 14,3 48,0 26,7 24,0 25,0 56,0 29,0 16,0 11,0 27,7 28,2 20,9
1 125,0 15,9 54,0 33,4 25,0 27,0 60,0 35,8 18,0 13,0 34,5 34,9 26,6
1 1⁄4 135,0 17,5 64,0 42,2 25,0 27,0 64,0 44,4 21,0 14,0 43,2 43,7 35,1
1 1⁄2 155,0 19,1 70,0 48,3 29,0 30,0 67,0 50,3 23,0 16,0 49,5 50,0 40,9
2 165,0 20,7 84,0 60,3 32,0 33,0 68,0 63,5 29,0 17,0 61,9 62,5 52,5
2 1⁄2 190,0 23,9 100,0 73,0 37,0 38,0 75,0 76,2 32,0 19,0 74,6 75,4 62,7
3 210,0 27,0 117,0 88,9 41,0 43,0 78,0 92,2 32,0 21,0 90,7 91,4 77,9
3 1⁄2 230,0 28,6 133,0 101,6 43,0 44,0 79,0 104,9 37,0 . . . 103,4 104,1 90,1
4 255,0 30,2 146,0 114,3 46,0 48,0 84,0 117,6 37,0 . . . 116,1 116,8 102,3
5 280,0 33,4 178,0 141,3 49,0 51,0 97,0 144,4 43,0 . . . 143,8 144,4 128,2
6 320,0 35,0 206,0 168,3 51,0 52,0 97,0 171,4 47,0 . . . 170,7 171,4 154,1
8 380,0 39,7 260,0 219,1 60,0 62,0 110,0 222,2 51,0 . . . 221,5 222,2 202,7
10 445,0 46,1 321,0 273,0 65,0 95,0 116,0 276,2 56,0 . . . 276,2 277,4 254,6
12 520,0 49,3 375,0 323,8 71,0 102,0 129,0 328,6 61,0 . . . 327,0 328,2 304,8
14 585,0 52,4 425,0 355,6 75,0 111,0 141,0 360,4 64,0 . . . 359,2 360,2
16 650,0 55,6 483,0 406,4 81,0 121,0 144,0 411,2 69,0 . . . 410,5 411,2
18 710,0 58,8 533,0 457,0 87,0 130,0 157,0 462,0 70,0 . . . 461,8 462,3
20 775,0 62,0 587,0 508,0 94,0 140,0 160,0 512,8 74,0 . . . 513,1 514,4
24 915,0 68,3 702,0 610,0 105,0 152,0 167,0 614,4 83,0 . . . 616,0 616,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B2 for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth # Lapped flange shall be 1.6 mm thicker than table value.
ahlsell 53
AsMe B16.5 PiPe Flanges
CLASS 300 FLANGES
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RF dimensions RTJ dimensions Bolt hole drilling Stud bolt length
Nominal Pipe Groove Groove Groove Groove Bolt Bolt No of Bolt 2,0mm Ring Size OD Height OD Height number Pitch Depth Width Circle hole bolts diam. RF Joint
NPS R k E P E F W Bh L L
1/2 34,9 2,0 51,0 5,54 R11 34,14 5,54 7,14 66,7 15,9 4 1/2 65,0 75,0 3/4 42,9 2,0 63,5 6,35 R13 42,88 6,35 8,74 82,6 19,1 4 5/8 75,0 90,0 1 50,8 2,0 70,0 6,35 R16 50,80 6,35 8,74 88,9 19,1 4 5/8 75,0 90,0 1 1⁄4 63,5 2,0 79,5 6,35 R18 60,33 6,35 8,74 98,4 19,1 4 5/8 85,0 95,0 1 1⁄2 73,0 2,0 90,5 6,35 R20 68,27 6,35 8,74 114,3 22,2 4 3/4 90,0 100,0 2 92,1 2,0 108,0 7,92 R23 82,55 7,92 11,91 127,0 19,1 8 5/8 90,0 100,0 2 1⁄2 104,8 2,0 127,0 7,92 R26 101,60 7,92 11,91 149,2 22,2 8 3/4 100,0 115,0 3 127,0 2,0 146,0 7,92 R31 123,83 7,92 11,91 168,3 22,2 8 3/4 110,0 120,0 3 1⁄2 139,7 2,0 159,0 7,92 R34 131,78 7,92 11,91 184,2 22,2 8 3/4 110,0 125,0 4 157,2 2,0 175,0 7,92 R37 149,23 7,92 11,91 200,0 22,2 8 3/4 115,0 125,0 5 185,7 2,0 210,0 7,92 R41 180,98 7,92 11,91 235,0 22,2 8 3/4 120,0 135,0 6 215,9 2,0 241,0 7,92 R45 211,12 7,92 11,91 269,9 22,2 12 3/4 120,0 140,0 8 269,9 2,0 302,0 7,92 R49 269,88 7,92 11,91 330,2 25,4 12 7/8 140,0 150,0 10 323,8 2,0 356,0 7,92 R53 323,85 7,92 11,91 387,4 28,6 16 1 160,0 170,0 12 381,0 2,0 413,0 7,92 R57 381,00 7,92 11,91 450,8 31,8 16 1 1⁄8 170,0 185,0 14 412,8 2,0 457,0 7,92 R61 419,10 7,92 11,91 514,4 31,8 20 1 1⁄8 180,0 190,0 16 469,9 2,0 508,0 7,92 R65 469,90 7,92 11,91 571,5 34,9 20 1 1⁄4 190,0 205,0 18 533,4 2,0 575,0 7,92 R69 533,40 7,92 11,91 628,6 34,9 24 1 1⁄4 195,0 210,0 20 584,2 2,0 635,0 9,53 R73 584,20 9,53 13,49 685,8 34,9 24 1 1⁄4 205,0 220,0
24 692,2 2,0 749,0 11,13 R77 692,15 11,13 16,66 812,8 41,3 24 1 1⁄2 230,0 255,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B2 for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth
DIMENSIONS OF CLASS 300 FLANGES (mm)
WR
O
k min.
P
54 ahlsell
PiPe Flanges asMe B16.5
CLASS 400 FLANGES
DIMENSIONS OF CLASS 400 FLANGES (mm)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Flange dimensions HUB dimensions Length Through HUB Threaded flange SW Bore
Nominal Pipe OD Large Small Thr. Weld Counter Thread Socket Slip-On, WeldSize flange Thickn. end end Slip. Lapped neck bore length depth Lapped neck
NPS O tf min. X A Y Y Y Q min. T min. D B min. B min. B
1/2
3/4
1
1 1⁄4
1 1⁄2
2
2 1⁄2
3
3 1⁄2
4 255,0 35,0 146,0 114,3 51,0 51,0 89,0 117,6 37,0 . . . 116,1 116,8
5 280,0 38,1 178,0 141,3 54,0 54,0 102,0 144,4 43,0 . . . 143,8 144,5
6 320,0 41,3 206,0 168,3 57,0 57,0 103,0 171,4 46,0 . . . 170,7 171,4
8 380,0 47,7 260,0 219,1 68,0 68,0 117,0 222,2 51,0 . . . 221,5 222,2
10 445,0 54,0 321,0 273,0 73,0 102,0 124,0 276,2 56,0 . . . 276,2 277,4
12 520,0 57,2 375,0 323,8 79,0 108,0 137,0 328,6 61,0 . . . 327,0 328,2
14 585,0 60,4 425,0 355,6 84,0 117,0 149,0 360,4 64,0 . . . 359,2 360,2
16 650,0 63,5 483,0 406,4 94,0 127,0 152,0 411,2 69,0 . . . 410,5 411,2
18 710,0 66,7 533,0 457,0 98,0 137,0 165,0 462,0 70,0 . . . 461,8 462,3
20 775,0 69,9 587,0 508,0 102,0 146,0 168,0 512,8 74,0 . . . 513,1 514,4
24 915,0 76,2 702,0 610,0 114,0 159,0 175,0 614,4 83,0 . . . 616,0 616,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. (1) the tolerance for E is only applicable for groove depth
To be
specified
by
purchaser
Use Class 600 dimensions in these sizes
ahlsell 55
AsMe B16.5 PiPe Flanges
CLASS 400 FLANGES
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RF dimensions RTJ dimensions Bolt hole drilling Stud bolt length
Nominal Pipe Groove Groove Groove Groove Bolt Bolt No of Bolt 7,0 mm Ring Size OD Height OD Height number Pitch Depth Width Circle hole RF diam. RF Joint
NPS R k E P E F W Bh L L
1/2
3/4
1
1 1⁄4
1 1⁄2
2
2 1⁄2
3
3 1⁄2
4 157,2 7,0 175,0 7,92 R37 149,23 7,92 11,91 200,0 25,4 8 7/8 140,0 140,0
5 185,7 7,0 210,0 7,92 R41 180,98 7,92 11,91 235,0 25,4 8 7/8 145,0 145,0
6 215,9 7,0 241,0 7,92 R45 211,12 7,92 11,91 269,9 25,4 12 7/8 150,0 150,0
8 269,9 7,0 302,0 7,92 R49 269,88 7,92 11,91 330,0 28,6 12 1 170,0 170,0
10 323,8 7,0 356,0 7,92 R53 323,85 7,92 11,91 387,4 31,8 16 1 1⁄8 190,0 190,0
12 381,0 7,0 413,0 7,92 R57 381,00 7,92 11,91 450,8 34,9 16 1 1⁄4 205,0 205,0
14 412,8 7,0 457,0 7,92 R61 419,10 7,92 11,91 514,4 34,9 20 1 1⁄4 210,0 210,0
16 469,9 7,0 508,0 7,92 R65 469,90 7,92 11,91 571,5 38,1 20 1 3⁄8 220,0 220,0
18 533,4 7,0 575,0 7,92 R69 533,40 7,92 11,91 628,6 38,1 24 1 3⁄8 230,0 230,0
20 584,2 7,0 635,0 9,53 R73 584,20 9,53 13,49 685,8 41,3 24 1 1⁄2 240,0 250,0
24 692,2 7,0 749,0 11,13 R77 692,15 11,13 16,66 812,8 47,6 24 1 3⁄4 265,0 280,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. (1) the tolerance for E is only applicable for groove depth
DIMENSIONS OF CLASS 400 FLANGES (mm)
WR
O
k min.
P
Use Class 600 dimensions in these sizes
56 ahlsell
PiPe Flanges asMe B16.5
CLASS 600 FLANGES
DIMENSIONS OF CLASS 600 FLANGES (mm)
To be
specified
by
purchaser
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Flange dimensions HUB dimensions Length Through HUB Threaded flange SW Bore
Nominal Thr. Pipe OD Large Small Slip. Weld Counter Thread Socket Slip-On, Weld Size flange Thickn. end end SW Lapped neck bore length depth SW Lapped neck
NPS O tf min. X A Y Y Y Q min. T min. D B min. B min. B
1/2 95,0 14,3 38,0 21,3 22,0 22,0 52,0 23,6 16,0 10,0 22,2 22,9
3/4 115,0 15,9 48,0 26,7 25,0 25,0 57,0 29,0 16,0 11,0 27,7 28,2
1 125,0 17,5 54,0 33,4 27,0 27,0 62,0 35,8 18,0 13,0 34,5 34,9
1 1⁄4 135,0 20,7 64,0 42,2 29,0 29,0 67,0 44,4 21,0 14,0 43,2 43,7
1 1⁄2 155,0 22,3 70,0 48,3 32,0 32,0 70,0 50,6 23,0 16,0 49,5 50,0
2 165,0 25,4 84,0 60,3 37,0 37,0 73,0 63,5 29,0 17,0 61,9 62,5
2 1⁄2 190,0 28,6 100,0 73,0 41,0 41,0 79,0 76,2 32,0 19,0 74,6 75,4
3 210,0 31,8 117,0 88,9 46,0 46,0 83,0 92,2 35,0 21,0 90,7 91,4
3 1⁄2 230,0 35,0 133,0 101,6 49,0 49,0 86,0 104,9 40,0 , , , 103,4 104,1
4 275,0 38,1 152,0 114,3 54,0 54,0 102,0 117,6 42,0 , , , 116,1 116,8
5 330,0 44,5 189,0 141,3 60,0 60,0 114,0 144,4 48,0 , , , 143,8 144,4
6 355,0 47,7 222,0 168,3 67,0 67,0 117,0 171,4 51,0 , , , 170,7 171,4
8 420,0 55,6 273,0 219,1 76,0 76,0 133,0 222,2 58,0 , , , 221,5 222,2
10 510,0 63,5 343,0 273,0 86,0 111,0 152,0 276,2 66,0 , , , 276,2 277,4
12 560,0 66,7 400,0 323,8 92,0 117,0 156,0 328,6 70,0 , , , 327,0 328,2
14 605,0 69,9 432,0 355,6 94,0 127,0 165,0 360,4 74,0 , , , 359,2 360,2
16 685,0 76,2 495,0 406,4 106,0 140,0 178,0 411,2 78,0 , , , 410,5 411,2
18 745,0 82,6 546,0 457,0 117,0 152,0 184,0 462,0 80,0 , , , 461,8 462,3
20 815,0 88,9 610,0 508,0 127,0 165,0 190,0 512,8 83,0 , , , 513,1 514,4
24 940,0 101,6 718,0 610,0 140,0 184,0 203,0 614,4 93,0 , , , 616,0 616,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B2for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth
ahlsell 57
AsMe B16.5 PiPe Flanges
CLASS 600 FLANGES
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RF dimensions RTJ dimensions Bolt hole drilling Stud bolt length
Nominal Pipe Groove Groove Groove Groove Bolt Bolt No of Bolt 7.0 mm Ring Size OD Height OD Height number Pitch Depth Width Circle hole bolts diam. RF Joint
NPS R k E P E F W Bh L L
1/2 34,9 7,0 51,0 5,54 R11 34,14 5,54 7,14 66,7 15,9 4 1/2 75,0 75,0
3/4 42,9 7,0 63,5 6,35 R13 42,88 6,35 8,74 82,6 19,1 4 5/8 90,0 90,0
1 50,8 7,0 70,0 6,35 R16 50,80 6,35 8,74 88,9 19,1 4 5/8 90,0 90,0
1 1⁄4 63,5 7,0 79,5 6,35 R18 60,33 6,35 8,74 98,4 19,1 4 5/8 95,0 95,0
1 1⁄2 73,0 7,0 90,5 6,35 R20 68,27 6,35 8,74 114,3 22,2 4 3/4 110,0 110,0
2 92,1 7,0 108,0 7,92 R23 82,55 7,92 11,91 127,0 19,1 8 5/8 110,0 110,0
2 1⁄2 104,8 7,0 127,0 7,92 R26 101,60 7,92 11,91 149,2 22,2 8 3/4 120,0 120,0
3 127,0 7,0 146,0 7,92 R31 123,83 7,92 11,91 168,3 22,2 8 3/4 125,0 125,0
3 1⁄2 139,7 7,0 159,0 7,92 R34 131,78 7,92 11,91 184,2 25,4 8 7/8 140,0 140,0
4 157,2 7,0 175,0 7,92 R37 149,23 7,92 11,91 215,9 25,4 8 7/8 145,0 145,0
5 185,7 7,0 210,0 7,92 R41 180,98 7,92 11,91 266,7 28,6 8 1 165,0 165,0
6 215,9 7,0 241,0 7,92 R45 211,12 7,92 11,91 292,1 28,6 12 1 170,0 170,0
8 269,9 7,0 302,0 7,92 R49 269,88 7,92 11,91 349,2 31,8 12 1 1⁄8 190,0 195,0
10 323,8 7,0 356,0 7,92 R53 323,85 7,92 11,91 431,8 34,9 16 1 1⁄4 215,0 215,0
12 381,0 7,0 413,0 7,92 R57 381,00 7,92 11,91 489,0 34,9 20 1 1⁄4 220,0 220,0
14 412,8 7,0 457,0 7,92 R61 419,10 7,92 11,91 527,0 38,1 20 1 3⁄8 235,0 235,0
16 469,9 7,0 508,0 7,92 R65 469,90 7,92 11,91 603,2 41,3 20 1 1⁄2 255,0 255,0
18 533,4 7,0 575,0 7,92 R69 533,40 7,92 11,91 654,0 44,5 20 1 5⁄8 275,0 275,0
20 584,2 7,0 635,0 9,53 R73 584,20 9,53 13,49 723,9 44,5 24 1 5⁄8 285,0 290,0
24 692,2 7,0 749,0 11,13 R77 692,15 11,13 16,66 838,2 50,8 24 1 7⁄8 330,0 335,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth
DIMENSIONS OF CLASS 600 FLANGES (mm)
WR
O
k min.
P
58 ahlsell
PiPe Flanges asMe B16.5
DIMENSIONS OF CLASS 900 FLANGES (mm)
CLASS 900 FLANGES
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Flange dimensions HUB dimensions Length Through HUB Threaded flange SW Bore
Nominal Pipe OD Large Small Thr. Weld Counter Thread Socket Slip-On Weld Size flange Thickn. end end Slip. Lapped neck bore length depth Lapped neck
NPS O tf min. X A Y Y Y Q min. T min. D B min. B min. B
1/2
3/4
1
1 1⁄4
1 1⁄2
2
2 1⁄2
3 240,0 38,1 127,0 88,9 54,0 54,0 102,0 92,2 42,0 . . . 90,7 91,4
4 290,0 44,5 159,0 114,3 70,0 70,0 114,0 117,6 48,0 . . . 116,1 116,8
5 350,0 50,8 190,0 141,3 79,0 79,0 127,0 144,4 54,0 . . . 143,8 144,4
6 380,0 55,6 235,0 168,3 86,0 86,0 140,0 171,4 58,0 . . . 170,7 171,4
8 470,0 63,5 298,0 219,1 102,0 114,0 162,0 222,2 64,0 . . . 221,5 222,2
10 545,0 69,9 368,0 273,0 108,0 127,0 184,0 276,2 72,0 . . . 276,2 277,4
12 610,0 79,4 419,0 323,8 117,0 143,0 200,0 328,6 77,0 . . . 327,0 328,2
14 640,0 85,8 451,0 355,6 130,0 156,0 213,0 360,4 83,0 . . . 359,2 360,2
16 705,0 88,9 508,0 406,4 133,0 165,0 216,0 411,2 86,0 . . . 410,5 411,2
18 785,0 101,6 565,0 457,0 152,0 190,0 229,0 462,0 89,0 . . . 461,8 462,3
20 855,0 108,0 622,0 508,0 159,0 210,0 248,0 512,8 93,0 . . . 513,1 514,4
24 1040,0 139,7 749,0 610,0 203,0 267,0 292,0 614,4 102,0 . . . 616,0 616,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. (1) the tolerance for E is only applicable for groove depth
To be
specified
by
purchaser
Use Class 1500 dimensions in these sizes
ahlsell 59
AsMe B16.5 PiPe Flanges
CLASS 900 FLANGES
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RF dimensions RTJ dimensions Bolt hole drilling Stud bolt length
Nominal
Pipe Groove Groove Groove Groove Bolt Bolt No of Bolt 7,0 mm Ring Size OD Height OD Height number Pitch Depth Width Circle hole bolts diam. RF Joint
NPS R k E P E F W Bh L L
1/2
3/4 1 1 1⁄4 1 1⁄2 Use Class 1500 dimensions in these sizes 2 2 1⁄2 3 127,0 7,0 156,0 7,92 R31 123,83 7,92 11,91 190,5 25,4 8 7/8 145,0 145,0
4 157,2 7,0 181,0 7,92 R37 149,23 7,92 11,91 235,0 31,8 8 1 1⁄8 170,0 170,0
5 185,7 7,0 216,0 7,92 R41 180,98 7,92 11,91 279,4 34,9 8 1 1⁄4 190,0 190,0
6 215,9 7,0 241,0 7,92 R45 211,12 7,92 11,91 317,5 31,8 12 1 1⁄8 190,0 195,0
8 269,9 7,0 308,0 7,92 R49 269,88 7,92 11,91 393,7 38,1 12 1 3⁄8 220,0 220,0
10 323,8 7,0 362,0 7,92 R53 323,85 7,92 11,91 469,9 38,1 16 1 3⁄8 235,0 235,0
12 381,0 7,0 419,0 7,92 R57 381,00 7,92 11,91 533,4 38,1 20 1 3⁄8 255,0 255,0
14 412,8 7,0 467,0 11,13 R62 419,10 11,13 16,66 558,8 41,3 20 1 1⁄2 275,0 280,0
16 469,9 7,0 524,0 11,13 R66 469,90 11,13 16,66 616,0 44,5 20 1 5⁄8 285,0 290,0
18 533,4 7,0 594,0 12,70 R70 533,40 12,70 19,84 685,8 50,8 20 1 7⁄8 325,0 335,0
20 584,2 7,0 648,0 12,70 R74 584,20 12,70 19,84 749,3 54,0 20 2 350,0 360,0
24 692,2 7,0 772,0 15,88 R78 692,15 15,88 26,97 901,7 66,7 20 2 1⁄2 440,0 455,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. (1) the tolerance for E is only applicable for groove depth
DIMENSIONS OF CLASS 900 FLANGES (mm)
WR
O
k min.
P
60 ahlsell
PiPe Flanges asMe B16.5
DIMENSIONS OF CLASS 1500 FLANGES (mm)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Flange dimensions HUB dimensions Length Through HUB Threaded flange SW Bore
Nominal Thr. Pipe OD Large Small Slip, Weld Counter Thread Socket Slip-On, Weld Size fla nge Thickn. end end Sw. Lapped neck bore length depth SW Lapped neck
NPS O tf min. X A Y Y Y Q min. T min. D B min. B min. B
1/2 120,0 22,3 38,0 21,3 32,0 32,0 60,0 23,6 23,0 10,0 22,2 22,9
3/4 130,0 25,4 44,0 26,7 35,0 35,0 70,0 29,0 26,0 11,0 27,7 28,2
1 150,0 28,6 52,0 33,4 41,0 41,0 73,0 35,8 29,0 13,0 34,5 34,9
1 1⁄4 160,0 28,6 64,0 42,2 41,0 41,0 73,0 44,4 31,0 14,0 43,2 43,7
1 1⁄2 180,0 31,8 70,0 48,3 44,0 44,0 83,0 50,6 32,0 16,0 49,5 50,0
2 215,0 38,1 105,0 60,3 57,0 57,0 102,0 63,5 39,0 17,0 61,9 62,5
2 1⁄2 245,0 41,3 124,0 73,0 64,0 64,0 105,0 76,2 48,0 19,0 74,6 75,4
3 265,0 47,7 133,0 88,9 . . . 73,0 117,0 . . . . . . . . . . . . 91,4
4 310,0 54,0 162,0 114,3 . . . 90,0 124,0 . . . . . . . . . . . . 116,8
5 375,0 73,1 197,0 141,3 . . . 105,0 156,0 . . . . . . . . . . . . 144,4
6 395,0 82,6 229,0 168,3 . . . 119,0 171,0 . . . . . . . . . . . . 171,4
8 485,0 92,1 292,0 219,1 . . . 143,0 213,0 . . . . . . . . . . . . 222,2
10 585,0 108,0 368,0 273,0 . . . 178,0 254,0 . . . . . . . . . . . . 277,4
12 675,0 123,9 451,0 323,8 . . . 219,0 283,0 . . . . . . . . . . . . 328,2
14 750,0 133,4 495,0 355,6 . . . 241,0 298,0 . . . . . . . . . . . . 360,2
16 825,0 146,1 552,0 406,4 . . . 260,0 311,0 . . . . . . . . . . . . 411,2
18 915,0 162,0 597,0 457,0 . . . 276,0 327,0 . . . . . . . . . . . . 462,3
20 985,0 177,8 641,0 508,0 . . . 292,0 356,0 . . . . . . . . . . . . 514,4
24 1170,0 203,2 762,0 610,0 . . . 330,0 406,0 . . . . . . . . . . . . 616,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B2for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth
CLASS 1500 FLANGES
To be
specified
by
purchaser
ahlsell 61
AsMe B16.5 PiPe Flanges
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RF dimensions RTJ dimensions Bolt hole drilling Stud bolt length
Nominal Pipe Groove Groove Groove Groove Bolt Bolt No of Bolt 7.0 mm Ring Size OD Height OD Height number Pitch Depth Width Circle hole bolts diam. RF Joint
NPS R k E P E F W Bh L L
1/2 34,9 7,0 60,5 6,35 R12 39,67 6,35 8,74 82,6 22,2 4 3/4 110,0 110,0
3/4 42,9 7,0 66,5 6,35 R14 44,45 6,35 8,74 88,9 22,2 4 3/4 115,0 115,0
1 50,8 7,0 71,5 6,35 R16 50,80 6,35 8,74 101,6 25,4 4 7/8 125,0 125,0
1 1⁄4 63,5 7,0 81,0 6,35 R18 60,33 6,35 8,74 111,1 25,4 4 7/8 125,0 125,0
1 1⁄2 73,0 7,0 92,0 6,35 R20 68,27 6,35 8,74 123,8 28,6 4 1 140,0 140,0
2 92,1 7,0 124,0 7,92 R24 95,25 7,92 11,91 165,1 25,4 8 7/8 145,0 145,0
2 1⁄2 104,8 7,0 137,0 7,92 R27 107,95 7,92 11,91 190,5 28,6 8 1 160,0 160,0
3 127,0 7,0 168,0 7,92 R35 136,53 7,92 11,91 230,2 31,8 8 1 1⁄8 180,0 180,0
4 157,2 7,0 194,0 7,92 R39 161,93 7,92 11,91 241,3 34,9 8 1 1⁄4 195,0 195,0
5 185,7 7,0 229,0 7,92 R44 193,68 7,92 11,91 292,1 41,3 8 1 1⁄2 250,0 250,0
6 215,9 7,0 248,0 9,53 R46 211,14 9,53 13,49 317,5 38,1 12 1 3⁄8 260,0 265,0
8 269,9 7,0 318,0 11,13 R50 269,88 11,13 16,66 393,7 44,5 12 1 5⁄8 290,0 325,0
10 323,8 7,0 371,0 11,13 R54 323,85 11,13 16,66 482,6 50,8 12 1 7⁄8 335,0 345,0
12 381,0 7,0 438,0 14,27 R58 381,00 14,27 23,01 571,5 54,0 16 2 375,0 385,0
14 412,8 7,0 489,0 15,88 R63 419,10 15,88 26,97 635,0 60,3 16 2 1⁄4 405,0 425,0
16 469,9 7,0 546,0 17,48 R67 469,90 17,48 30,18 704,8 66,7 16 2 1⁄2 445,0 470,0
18 533,4 7,0 613,0 17,48 R71 533,40 17,48 30,18 774,7 73,0 16 2 3⁄4 495,0 525,0
20 584,2 7,0 673,0 17,48 R75 584,20 17,48 33,32 831,8 79,4 16 3 540,0 565,0
24 692,2 7,0 794,0 20,62 R79 692,15 20,62 36,53 990,6 92,1 16 3 1⁄2 615,0 650,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. The dimensions B2 for SW flange equals B for Weld Neck. (1) the tolerance for E is only applicable for groove depth
DIMENSIONS OF CLASS 1500 FLANGES (mm)
CLASS 1500 FLANGES
WR
O
k min.
P
62 ahlsell
Asme B16.5 PIPe FLANGes
CLASS 2500 FLANGES
DIMENSIONS OF CLASS 2500 FLANGES (mm)
To be
specified
by
purchaser
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Flange dimensions HUB dimensions Length Through HUB Threaded flange SW Bore
Nominal Pipe OD Large Small Weld Counter Thread Socket Slip-On, Weld Size flange Thickn. end end Thr. Lapped neck bore length depth SW Lapped neck
NPS O tf min. X A Y Y Y Q min. T min. D B min. B min. B
1/2 135,0 30,2 43,0 21,3 40,0 40,0 73,0 23,6 29,0 . . . . . . 22,9
3/4 140,0 31,8 51,0 26,7 43,0 43,0 79,0 29,0 32,0 . . . . . . 28,2
1 160,0 35,0 57,0 33,4 48,0 48,0 89,0 35,8 35,0 . . . . . . 34,9
1 1⁄4 185,0 38,1 73,0 42,2 52,0 52,0 95,0 44,4 39,0 . . . . . . 43,7
1 1⁄2 205,0 44,5 79,0 48,3 60,0 60,0 111,0 50,6 45,0 . . . . . . 50,0
2 235,0 50,9 95,0 60,3 70,0 70,0 127,0 63,5 51,0 . . . . . . 62,5
2 1⁄2 265,0 57,2 114,0 73,0 79,0 79,0 143,0 76,2 58,0 . . . . . . 75,4
3 305,0 66,7 133,0 88,9 . . . 92,0 168,0 . . . . . . . . . . . . 91,4
4 355,0 76,2 165,0 114,3 . . . 108,0 190,0 . . . . . . . . . . . . 116,8
5 420,0 92,1 203,0 141,3 . . . 130,0 229,0 . . . . . . . . . . . . 144,4
6 485,0 108,0 235,0 168,3 . . . 152,0 273,0 . . . . . . . . . . . . 171,4
8 550,0 127,0 305,0 219,1 . . . 178,0 318,0 . . . . . . . . . . . . 222,2
10 675,0 165,1 375,0 273,0 . . . 229,0 419,0 . . . . . . . . . . . . 277,4
12 760,0 184,2 441,0 323,8 . . . 254,0 464,0 . . . . . . . . . . . . 328,2
NOTE: All dimensions except NPS and bolt diameter are in millimeters. (1) the tolerance for E is only applicable for groove depth
PIPe FLANGes Asme B16.5
ahlsell 63
DIMENSIONS OF CLASS 2500 FLANGES (mm)
CLASS 2500 FLANGES
WR
O
K min.
P
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 RF dimensions RTJ dimensions Bolt hole drilling Stud bolt length
Nominal Pipe Groove Groove Groove Groove Bolt Bolt No of Bolt 7,0 mm Ring Size OD Height OD Height number Pitch Depth Width Circle hole bolts diam. RF Joint
NPS R K E P E F W Bh L L
1/2 34,9 7,0 65,0 6,35 R13 42,88 6,35 8,74 88,9 22,2 4 3/4 120,0 120,0
3/4 42,9 7,0 73,0 6,35 R16 50,80 6,35 8,74 95,2 22,2 4 3/4 125,0 125,0
1 50,8 7,0 82,5 6,35 R18 60,33 6,35 8,74 108,0 25,4 4 7/8 140,0 140,0
1 1⁄4 63,5 7,0 102,0 7,92 R21 72,23 7,92 11,91 130,2 28,6 4 1 150,0 150,0
1 1⁄2 73,0 7,0 114,0 7,92 R23 82,55 7,92 11,91 146,0 31,8 4 1 1⁄8 170,0 170,0
2 92,1 7,0 133,0 7,92 R26 101,60 7,92 11,91 171,4 28,6 8 1 180,0 180,0
2 1⁄2 104,8 7,0 149,0 9,52 R28 111,13 9,52 13,49 196,8 31,8 8 1 1⁄8 195,0 205,0
3 127,0 7,0 168,0 9,53 R32 127,00 9,53 13,49 228,6 34,9 8 1 1⁄4 220,0 230,0
4 157,2 7,0 203,0 11,13 R38 157,18 11,13 16,66 273,0 41,3 8 1 1⁄2 255,0 260,0
5 185,7 7,0 241,0 12,70 R42 190,50 12,70 19,84 323,8 47,6 8 1 3⁄4 300,0 310,0
6 215,9 7,0 279,0 12,70 R47 228,60 12,70 19,84 368,3 54,0 8 2 345,0 355,0
8 269,9 7,0 340,0 14,27 R51 279,40 14,27 23,01 438,2 54,0 12 2 380,0 395,0
10 323,8 7,0 425,0 17,48 R55 342,90 17,48 30,18 539,8 66,7 12 2 1⁄2 490,0 510,0
12 381,0 7,0 495,0 17,48 R60 406,40 17,48 33,32 619,1 73,0 12 2 3⁄4 540,0 560,0
NOTE: All dimensions except NPS and bolt diameter are in millimeters. (1) the tolerance for E is only applicable for groove depth
Asme B16.5 PIPe FLANGes
64 ahlsell
DENOMINATION DESCRIPTION SIzE RANGE TOLERANCE
O Outside diameter <= 24” ± 1.6 mm
flange ring 1) >= 26” ± 3.2 mm
Weld neck:
B Inside diameter / bore <= 10” ± 1.0 mm
12” - 18” ± 1.5 mm
>= 20” + 3.0 / -1.5 mm
Slip-on, lap joint, socket weld, threaded
<= 10” + 1.0 / -0.0 mm
>= 12” + 1.5 / -0.0 mm
A Diameter small end <= 5” + 2.0 / -1.0 mm
of HUB / WN end >= 6” + 4.0 / -1.0 mm
X Diameter of HUB base <= 24” (dimension X) + 1.6 / -0.8 mm
>= 26” (dimension X) + 3.2 / -0.8 mm
W Drilling and facing Bolt circle diameter ± 1.5 mm
Center to center adjacent bolt holes ± 0.8 mm
Max eccentricity between bolt circle diameter
and machining facing diameter:
<= 2 1/2” 0.8 mm
>= 3” 1.5 mm
Y Overall HUB length <= 4” ± 1.5 mm
of WN flanges 5” - 10” + 1.5 / -3.0 mm
>= 12” + 3.0 / -5.0 mm
tf Thickness of flange ring <= 18” + 3.0 / -0.0 mm
>= 20” + 5.0 / -0.0 mm
E Groove depth Applicable for groove depth only + 0.4 / -0.0 mm
F Groove width ± 0.2 mm
P Groove pitch ± 0.13 mm
K RTJ raised portion + 0.50 / -0.00 mm
R RF raised portion 2.0 mm RF height ± 1.0 mm
7.0 mm RF height ± 0.5 mm
Tolerances B16.5 - 2003
1) These tolerances are not covered by ANSI B 16.5
ahlsell 65
66 ahlsell
ahlsell 67
FLAN
GE
SM
SS
SP
-44
FLANGesmss sP-44
68 ahlsell
FLANGes mss sP-44
Flange dim. Hub dimension RF dimensions RTJ dimensions Bolt hole drilling OD Large Length Groove Bolt Bolt No of Nominal OD flange Thickness end through OD Height OD number Pitch Depth Width Circle Hole bolts Pipe size O C min. X Y R K P L D Bc Bh
26” 870 66,7 676 119 749,3 2,0 - - - - - 806,4 35,1 24
28’’ 925 69,9 727 124 800,1 2,0 - - - - - 863,6 35,1 28
30’’ 985 73,1 781 135 857,2 2,0 - - - - - 914,4 35,1 28
32’’ 1060 79,4 832 143 914,4 2,0 - - - - - 977,9 41,2 28
34’’ 1110 81,0 883 148 965,2 2,0 - - - - - 1028,7 41,2 32
36’’ 1170 88,9 933 156 1022,4 2,0 - - - - - 1085,8 41,2 32
38’’ 1240 85,8 991 156 1073,2 2,0 - - - - - 1149,4 41,2 32
40’’ 1290 88,9 1041 162 1124,0 2,0 - - - - - 1200,2 41,2 36
42’’ 1345 95,3 1092 170 1193,8 2,0 - - - - - 1257,3 41,2 36
44’’ 1405 100,1 1143 176 1244,6 2,0 - - - - - 1314,4 41,2 40
46’’ 1455 101,6 1197 184 1295,4 2,0 - - - - - 1365,2 41,2 40
48’’ 1510 106,4 1248 190 1358,9 2,0 - - - - - 1422,4 41,2 44
50” 1570 109,6 1302 202 1409,7 2,0 - - - - - 1479,6 47,8 44
52” 1625 114,3 1353 208 1460,5 2,0 - - - - - 1536,7 47,8 44
54’’ 1685 119,1 1403 214 1511,3 2,0 - - - - - 1593,8 47,8 44
56’’ 1745 122,3 1457 227 1574,8 2,0 - - - - - 1651,0 47,8 48
58’’ 1805 127,0 1508 233 1625,6 2,0 - - - - - 1708,2 47,8 48
60’’ 1855 130,2 1559 238 1676,4 2,0 - - - - - 1759,0 47,8 52
NOTES: Bore (B) to be specified by purchacer OD of HUB at WN end (H) depends on material properties of flange versus joining piping - see section 5.3 of MSS SP-44.
MSS SP-44 CLASS 150 FLANGES
DIMENSIONS FOR MSS SP-44 CLASS 150 FLANGES (mm)
ahlsell 69
mss sP-44 FLANGes
NOTES: Bore (B) to be specified by purchacer OD of HUB at WN end (H) depends on material properties of flange versus joining piping - see section 5.3 of MSS SP-44.
Flange dimension Hub dimension RF dimensions RTJ dimensions Bolt hole drilling Thickn. Thickn. OD Large Length Groove Bolt Bolt No of Nominal OD flange WN Blind end through OD Height OD number Pitch Depth Width Circle Hole bolts Pipe size O C min. E. min X Y R K P L D Bc Bh
26” 970 77,8 82,6 721 183 749,3 2,0 810 R93 749,3 12,70 19,84 876,3 44,5 28 28’’ 1035 84,2 88,9 775 195 800,1 2,0 861 R94 800,1 12,70 19,84 939,8 44,5 28 30’’ 1090 90,5 93,7 827 208 857,2 2,0 917 R95 857,3 12,70 19,84 997,0 47,8 28 32’’ 1150 96,9 98,5 881 221 914,4 2,0 984 R96 914,4 14,27 23,01 1054,1 50,8 28 34’’ 1205 100,1 103,2 937 230 965,2 2,0 1035 R97 965,2 14,27 23,01 1104,9 50,8 28 36’’ 1270 103,2 109,6 991 240 1022,4 2,0 1092 R98 1022,4 14,27 23,01 1168,4 53,9 32 38’’ 1170 106,4 106,4 994 179 1028,7 2,0 - - - - - 1092,2 41,2 32 40’’ 1240 112,8 112,8 1048 192 1085,8 2,0 - - - - - 1155,7 44,5 32 42’’ 1290 117,5 117,5 1099 198 1136,6 2,0 - - - - - 1206,5 44,5 32 44’’ 1355 122,3 122,3 1149 205 1193,8 2,0 - - - - - 1263,6 47,8 32 46’’ 1415 127,0 127,0 1203 214 1244,6 2,0 - - - - - 1320,8 50,8 28 48’’ 1465 131,8 131,8 1254 222 1301,8 2,0 - - - - - 1371,6 50,8 32 50” 1530 138,2 138,2 1305 230 1358,9 2,0 - - - - - 1428,8 53,9 32 52” 1580 142,9 142,9 1356 237 1409,7 2,0 - - - - - 1479,6 53,9 32 54’’ 1660 150,9 150,9 1410 251 1466,8 2,0 - - - - - 1549,4 60,5 28 56’’ 1710 152,4 152,4 1464 259 1517,6 2,0 - - - - - 1600,2 60,5 28 58’’ 1760 157,2 157,2 1514 265 1574,8 2,0 - - - - - 1651,0 60,5 32 60’’ 1810 162,0 162,0 1565 271 1625,6 2,0 - - - - - 1701,8 60,5 32
MSS SP-44 CLASS 300 FLANGES
DIMENSIONS FOR MSS SP-44 CLASS 300 FLANGES (mm)
70 ahlsell
FLANGes mss sP-44
NOTES: Bore (B) to be specified by purchacer OD of HUB at WN end (H) depends on material properties of flange versus joining piping - see section 5.3 of MSS SP-44.
Flange dimension Hub dimension RF dimensions RTJ dimensions Bolt hole drilling Thickn. Thickn. OD Large Length Groove Bolt Bolt No of Nominal OD flange WN Blind end through OD Height OD number Pitch Depth Width Circle Hole bolts Pipe size O C min. E. min X Y R K P L D Bc Bh
26” 970 88,9 98,5 727 194 749,3 7,0 810 R93 749,3 12,70 19,84 876,3 47,8 28 28’’ 1035 95,3 104,8 783 206 800,1 7,0 861 R94 800,1 12,70 19,84 939,8 50,8 28 30’’ 1090 101,6 111,2 837 219 857,2 7,0 917 R95 857,3 12,70 19,84 997,0 53,9 28 32’’ 1150 108,0 115,9 889 232 914,4 7,0 984 R96 914,4 14,27 23,01 1054,1 53,9 28 34’’ 1205 111,2 122,3 945 241 965,2 7,0 1035 R97 965,2 14,27 23,01 1104,9 53,9 28 36’’ 1270 114,3 128,6 1000 251 1022,4 7,0 1092 R98 1022,4 14,27 23,01 1168,4 53,9 32 38’’ 1205 123,9 123,9 1003 206 1035,0 7,0 - - - - - 1117,6 47,8 32 40’’ 1270 130,2 130,2 1054 216 1092,2 7,0 - - - - - 1174,8 50,8 32 42’’ 1320 133,4 133,4 1108 224 1143,0 7,0 - - - - - 1225,6 50,8 32 44’’ 1385 139,7 139,7 1159 233 1200,2 7,0 - - - - - 1282,7 53,9 32 46’’ 1440 146,1 146,1 1213 244 1257,3 7,0 - - - - - 1339,8 53,9 36 48’’ 1510 152,4 152,4 1267 257 1308,1 7,0 - - - - - 1403,4 60,5 28 50” 1570 157,2 158,8 1321 268 1362,1 7,0 - - - - - 1460,5 60,5 32 52” 1620 162,0 163,6 1372 276 1412,9 7,0 - - - - - 1511,3 60,5 32 54’’ 1700 169,9 171,5 1426 289 1470,0 7,0 - - - - - 1581,2 66,6 28 56’’ 1755 174,7 176,3 1480 298 1527,2 7,0 - - - - - 1632,0 66,6 32 58’’ 1805 177,8 181,0 1530 306 1578,0 7,0 - - - - - 1682,8 60,6 32 60’’ 1885 185,8 189,0 1584 319 1635,1 7,0 - - - - - 1752,6 73,2 32
MSS SP-44 CLASS 400 FLANGES
DIMENSIONS FOR MSS SP-44 CLASS 400 FLANGES (mm)
ahlsell 71
mss sP-44 FLANGes
NOTES: Bore (B) to be specified by purchacer OD of HUB at WN end (H) depends on material properties of flange versus joining piping - see section 5.3 of MSS SP-44.
Flange dimension Hub dimension RF dimensions RTJ dimensions Bolt hole drilling Thickn. Thickn. OD Large Length Groove Bolt Bolt No of Nominal OD flange WN Blind end through OD Height OD number Pitch Depth Width Circle Hole bolts Pipe size O C min. E. min X Y R K P L D Bc Bh
26” 1015 108,0 125,5 748 222 749,3 7,0 810 R93 749,3 12,70 19,84 914,4 50,8 28 28’’ 1075 111,2 131,8 803 235 800,1 7,0 861 R94 800,1 12,70 19,84 965,2 53,9 28 30’’ 1130 114,3 139,7 862 248 857,2 7,0 917 R95 857,3 12,70 19,84 1022,4 53,9 28 32’’ 1195 117,5 147,7 918 260 914,4 7,0 984 R96 914,4 14,27 23,01 1079,5 60,5 28 34’’ 1245 120,7 154,0 973 270 965,2 7,0 1035 R97 965,2 14,27 23,01 1130,3 60,5 28 36’’ 1315 123,9 162,0 1032 283 1022,4 7,0 1092 R98 1022,4 14,27 23,01 1193,8 66,6 28 38’’ 1270 152,4 155,6 1022 254 1054,1 7,0 - - - - - 1162,0 60,5 28 40’’ 1320 158,8 162,0 1073 264 1111,2 7,0 - - - - - 1212,8 60,5 32 42’’ 1405 168,3 171,5 1127 279 1168,4 7,0 - - - - - 1282,7 66,6 28 44’’ 1455 173,1 177,8 1181 289 1225,6 7,0 - - - - - 1333,5 66,6 32 46’’ 1510 179,4 185,8 1235 300 1276,4 7,0 - - - - - 1390,6 66,6 32 48’’ 1595 189,0 195,3 1289 316 1333,5 7,0 - - - - - 1460,5 73,2 32 50” 1670 196,9 203,2 1343 329 1384,3 7,0 - - - - - 1524,0 79,3 28 52” 1720 203,2 209,6 1394 337 1435,1 7,0 - - - - - 1574,8 79,3 32 54’’ 1780 209,6 217,5 1448 349 1492,2 7,0 - - - - - 1632,0 79,3 32 56’’ 1855 217,5 225,5 1502 362 1543,0 7,0 - - - - - 1695,4 85,9 32 58’’ 1905 222,3 231,8 1553 370 1600,2 7,0 - - - - - 1746,2 85,9 32 60’’ 1995 233,4 242,9 1610 389 1657,4 7,0 - - - - - 1822,4 92,0 28
MSS SP-44 CLASS 600 FLANGES
DIMENSIONS FOR MSS SP-44 CLASS 600 FLANGES (mm)
72 ahlsell
FLANGes mss sP-44
NOTES: Bore (B) to be specified by purchacer OD of HUB at WN end (H) depends on material properties of flange versus joining piping - see section 5.3 of MSS SP-44.
Flange dimension Hub dimension RF dimensions RTJ dimensions Bolt hole drilling Thickn. Thickn. OD Large Length Groove Bolt Bolt No of Nominal OD flange WN Blind end through OD Height OD number Pitch Depth Width Circle Hole bolts Pipe size O C min. E. min X Y R K P L D Bc Bh
26” 1085 139,7 160,4 775 286 749,3 7,0 832 R100 749,3 17,48 30,18 952,5 73,2 20 28’’ 1170 142,9 171,5 832 298 800,1 7,0 889 R101 800,1 17,48 33,32 1022,4 79,3 20 30’’ 1230 149,3 182,6 889 311 857,2 7,0 946 R102 857,3 17,48 33,32 1085,8 79,3 20 32’’ 1315 158,8 193,7 946 330 914,4 7,0 1003 R103 914,4 17,48 33,32 1155,7 85,9 20 34’’ 1395 165,1 204,8 1006 349 965,2 7,0 1067 R104 965,2 20,62 36,52 1225,6 92,0 20 36’’ 1460 171,5 214,4 1064 362 1022,4 7,0 1124 R105 1022,4 20,62 36,52 1289,0 92,0 20 38’’ 1460 190,5 215,9 1073 352 1098,6 7,0 - - - - - 1289,0 92,0 20 40’’ 1510 196,9 223,9 1127 364 1162,8 7,0 - - - - - 1339,8 92,0 24 42’’ 1560 206,4 231,8 1176 371 1212,8 7,0 - - - - - 1390,6 92,0 24 44’’ 1650 214,4 242,9 1235 391 1270,0 7,0 - - - - - 1463,7 98,6 24 46’’ 1735 225,5 255,6 1292 411 1333,5 7,0 - - - - - 1536,7 104,7 24 48’’ 1785 233,4 263,6 1343 419 1384,3 7,0 - - - - - 1587,5 104,7 24
MSS SP-44 CLASS 900 FLANGES
DIMENSIONS FOR MSS SP-44 CLASS 900 FLANGES (mm)
ahlsell 73
mss sP-44 FLANGes
Denomination Description Size range Tolerance
O Outside diameter (>= 26”) ±3.2 mm flange ring - note 1
B Inside diameter / (>=20”) + 3.0 / -1.5 mm bore
H Diameter small end (>= 26”) + 5.0 / -1.5 mm of HUB / WN end
X Diameter of HUB base - (>= 26” dimension X) + 3.2 / -0.8 mm note 1 Drilling and facing Bolt circle diameter ±1.5 mm Center to center adjacent bolt holes ±0.8 mm Max eccentricity between bolt circle diam. and machining facing diameter 2.0 mm
Y Overall HUB length (>= 26”) ±5.0 mm
C or E Thickness of (>=20”) + 5.0 / -0.0 mm flange ring L Groove depth - note 2 Applicable for groove depth only + 0.4 / -0.0 mm
D Groove width - note 2 ±0.2 mm
P Groove pitch - note 2 ±0.13
K RTJ raised portion - note 2 + 0.50 / -0.00 mm
R RF raised portion 2.0 mm RF height (>=26”) ±2.0 mm 7.0 mm RF height (>=26”) ± 1.0 mm
NOTES: 1) These tolerances are not covered by MSS SP-44, and are for guidance only. 2) These tolerances are not covered by MSS SP-44 - taken from ASME B16.5.
TOLERANCES MSS SP-44 - 2006
74 ahlsell
FLAN
GE
S - A
PI 6A
FLANGesAPI 6A
ahlsell 75
76 ahlsell
FLANGes API 6A - tyPe 6B
OD 2 1/16 to 5 1/8 +/- 2mm
OD 7 1/16 to 11 +/- 3mm
LN +/- 1.6mm
HL 2 1/16 to 5 1/8 +2.3/ -0.8mm
HL 7 1/16 to 11 +4.0/ -0.8mm
T +3/ -0mm
K /-0mm
Q /-0mm
Bolt holes 2 1/16 to 7 1/16 +2.0/ -0.5mm
Bolt holes 9 to 11 +2.5/ -0.5mm
P +/-0.13mm
F +/-0.20mm
E +0.5/-0mm
All other dimension - as X.X +/-0.5mm
All other dimension - as X.XX +/-0.1mm
TOLERANCES:
NOTE: All dimensions except NPS and bolt diameter in millimeters
API 6A - type 6B flangesWeld neck, Threaded and Integral flanges are available in 2000, 3000 and 5000 psi rating
TYPE 6B WELD NECK FLANGES - 5000PSI
Nominal Nom. Max OD Raised Total Basic Large Small HUB OD bolt No. of Bolt Bolt Stud Ring Pitch of Width of Depth of
size bore bore flange face OD thickn. thickn. HUB HUB length circle bolts diam. hole bolt number groove groove groove
diam. diam. diam. length
(inch) JL OD K T Q X HL LN BC (inch) Lssb R/ RX P F E
2 1⁄16 52 43,7 215 124 46,1 38,1 104,8 60,3 109,5 165,1 8 7/8 26 150 24 95,25 11,91 7,9
2 9⁄16 65 54,9 245 137 49,3 41,3 123,8 73,0 112,7 190,5 8 1 29 165 27 107,95 11,91 7,9
3 1⁄8 79 67,5 265 168 55,6 47,7 133,3 88,9 125,4 203,2 8 1 1⁄8 32 185 35 136,53 11,91 7,9
4 1⁄16 103 88,1 310 194 62,0 54,0 161,9 114,3 131,8 241,3 8 1 1⁄4 35 205 39 161,93 11,91 7,9
5 1⁄8 130 110,3 375 229 81,0 73,1 196,8 141,3 163,5 292,1 8 1 1⁄2 42 255 44 193,68 11,91 7,9
7 1⁄16 178 132,6 395 248 92,1 82,6 228,6 168,3 181,0 317,5 12 1 3⁄8 39 275 46 211,15 13,49 9,7
9 228 173,8 485 318 103,2 92,1 292,1 219,1 223,8 393,7 12 1 5⁄8 45 305 50 269,88 16,66 11,2
11 279 216,7 585 371 119,1 108 368,3 273,1 265,1 482,6 12 1 7⁄8 51 350 54 323,85 16,66 11,2
ahlsell 77
API 6A - tyPe 6B FLANGes
78 ahlsell
FLANGes API 6A - tyPe 6Bx
NOTE: All dimensions except NPS and bolt diameter in millimeters
TYPE 6BX WELD NECK FLANGES - 10.000/15.000/20.000 PSI
API 6A - type 6BX flangesWeld neck, Blind and Test flanges are available in 10.000, 15.000 and 20.000 psi rating Integral flanges are available in 2000, 3000, 5000, 10.000, 15.000 and 20.000 psi rating
OD 1 13/16 to 5 1/8 +/- 2mm
OD 7 1/16 to 16 3/4 +/- 3mm
J1 +0/ -3mm
J2 /-0mm
J3 /-0mm
T +3/ -0mm
K +/-1.6mm
Bolt holes 1 13/16 to 5 1/8 +2.0/ -0.5mm
Bolt holes 7 1/16 to 16 3/4 +2.5/ -0.5mm
G +0.1/-0mm
N +0.1/-0mm
E +0.5/-0mm
All other dimension - as X.X +/-0.5mm
All other dimension - as X.XX +/-0.1mm
TOLERANCES:
Nominal Nom. Max OD Raised Total Large Small HUB OD bolt No. of Bolt Bolt Stud Ring OD of Width Depth
size bore bore flange face OD thickn. HUB HUB length circle bolts diam. hole bolt number groove of of
diam. diam. diam. length groove groove
(inch) B B OD K T J1 J2 J3 BC (inch) Lssb BX G N E
10.000 psi
1 13⁄16 46 46,8 185 105 42,1 88,9 65,1 48,4 146,0 8 3/4 23 125 151 77,77 11,84 5,56
2 1⁄16 52 53,2 200 111 44,1 100,0 74,6 51,6 158,8 8 3/4 23 135 152 86,23 12,65 5,95
2 9⁄16 65 65,9 230 132 51,2 120,7 92,1 57,2 184,2 8 7/8 26 150 153 102,77 14,07 6,75
3 1⁄16 78 78,6 270 152 58,4 142,1 110,3 63,5 215,9 8 1 29 170 154 119,00 15,39 7,54
4 1⁄16 103 104,0 315 185 70,3 182,6 146,1 73,0 258,8 8 1 1⁄8 32 205 155 150,62 17,73 8,33
5 1⁄8 130 131,0 360 221 79,4 223,8 182,6 81,0 300,0 12 1 1⁄8 32 220 169 176,66 16,92 9,53
7 1⁄16 179 180,2 480 302 103,2 301,6 254,0 95,2 403,2 12 1 1⁄2 42 285 156 241,83 23,39 11,11
9 228 229,4 550 359 123,9 374,7 327,1 93,7 476,2 16 1 1⁄2 42 330 157 299,06 26,39 12,70
11 279 280,2 655 429 141,3 450,9 400,1 103,2 565,2 16 1 3⁄4 48 380 158 357,23 29,18 14,29
13 5⁄8 346 346,9 770 518 168,3 552,5 495,3 114,3 673,1 20 1 7⁄8 51 440 159 432,64 32,49 15,88
16 3⁄4 425 426,2 870 576 168,3 655,6 601,7 76,2 776,3 24 1 7⁄8 51 445 162 478,33 17,91 8,33
15.000 psi
1 13⁄16 46 46,8 210 106 45,3 97,6 71,4 47,6 160,3 8 7/8 26 140 151 77,77 11,84 5,56
2 1⁄16 52 53,2 220 114 50,8 111,1 82,6 54,0 174,6 8 7/8 26 150 152 86,23 12,65 5,95
2 9⁄16 65 65,9 255 133 57,2 128,6 100,0 57,2 200,0 8 1 29 170 153 102,77 14,07 6,75
3 1⁄16 78 78,6 290 154 64,3 154,0 122,2 63,5 230,2 8 1 1⁄8 32 190 154 119,00 15,39 7,54
4 1⁄16 103 104,0 360 194 78,6 195,3 158,8 73,0 290,5 8 1 3⁄8 39 235 155 150,62 17,73 8,33
5 1⁄8 130 131,0 420 225 98,5 244,5 200,0 81,8 342,9 12 1 1⁄2 42 290 169 176,66 16,92 9,53
7 1⁄16 179 180,2 505 305 119,1 325,4 276,2 92,1 428,6 16 1 1⁄2 42 325 156 241,83 23,39 11,11
20.000 psi
1 13⁄16 46 46,8 255 117 63,5 133,4 109,5 49,2 203,2 8 1 29 190 151 77,77 11,84 5,56
2 1⁄16 52 53,2 285 132 71,5 154,0 127,0 52,4 230,2 8 1 1⁄8 32 210 152 86,23 12,65 5,95
2 9⁄16 65 65,9 325 151 79,4 173,0 144,5 58,7 261,9 8 1 1⁄4 35 235 153 102,77 14,07 6,75
3 1⁄16 78 78,6 355 171 85,8 192,1 160,3 63,5 287,3 8 1 3⁄8 39 255 154 119,00 15,39 7,54 4 1⁄16 103 104,0 445 219 106,4 242,9 206,4 73,0 357,2 8 1 3⁄4 48 310 155 150,62 17,73 8,33 7 1⁄16 179 180,2 655 352 165,1 385,8 338,1 96,8 554,0 16 2 54 445 156 241,83 23,39 11,11
ahlsell 79
API 6A - tyPe 6Bx FLANGes
80 ahlsell
FOR
GE
D FIT
TIN
GS
FORGeD FIttINGs
Asme B16.11 Bs3799
ahlsell 81
82 ahlsell
FORGeD steeL FIttINGs tHReADeD
90° elbows
45° elbows
90° ELBOWS - THREADED - B16.11
45° ELBOWS - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
B 22 22 25 33 38 46 56 62 75 92 109 146
C 21 21 25 28 33 38 44 51 60 76 86 106
2000 LB T 3,18 3,18 3,18 3,18 3,18 3,68 3,89 4,01 4,27 5,61 5,99 6,55
Appt Wt 0,08 0,08 0,11 0,23 0,28 0,46 0,80 1,00 1,60 2,30 4,35 10,25
Kg
B 22 25 33 38 46 56 62 75 84 102 121 152
C 21 25 28 33 38 44 51 60 64 83 95 114
3000 LB T 3,18 3,30 3,51 4,09 4,32 4,98 5,28 5,56 7,14 7,65 8,84 11,18
Appt Wt 0,14 0,14 0,27 0,37 0,60 1,08 1,22 2,45 2,50 5,25 7,40 13,00
Kg
B 25 33 38 46 56 62 75 84 102 121 146 152
C 25 28 33 38 44 51 60 64 83 95 106 114
6000 LB T 6,35 6,60 6,98 8,15 8,53 9,93 10,59 11,07 12,09 15,29 16,64 18,67
App Wt 0,31 0,31 0,50 0,69 1,25 1,65 2,75 3,22 6,25 10,00 17,00 18,00
Kg
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
B 22 22 25 33 38 46 56 62 75 92 109 146
C 17 17 19 22 25 28 33 35 43 52 64 79
2000 LB T 3,18 3,18 3,18 3,18 3,18 3,68 3,89 4,01 4,27 5,61 5,99 6,55
App Wt 0,10 0,10 0,11 0,21 0,24 0,39 0,70 0,85 1,23 3,00 3,50 9,00
Kg
B 22 25 33 38 46 56 62 75 84 102 121 152
C 17 19 22 25 28 33 35 43 44 52 64 79
3000 LB T 3,18 3,30 3,51 4,09 4,32 4,98 5,28 5,56 7,14 7,65 8,84 11,18
App Wt 0,13 0,13 0,25 0,36 0,53 0,78 1,02 1,70 2,35 5,40 6,00 10,50
Kg
B 25 33 38 46 56 62 75 84 102 121 146 152
6000 LB C 19 22 25 28 33 35 43 44 52 64 79 79
T 6,35 6,60 6,98 8,15 8,53 9,93 10,59 11,07 12,09 15,29 16,64 18,67
App Wt 0,25 0,25 0,35 0,60 0,95 1,22 1,35 2,55 5,60 8,00 15,50 13,00
Kg
ahlsell 83
tHReADeD FORGeD steeL FIttINGs
Tees – Equal and reducing
Crosses
TEES - THREADED - B16.11
CROSSES - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
B 22 22 25 33 38 46 56 62 75 92 109 146
C 21 21 25 28 33 38 44 51 60 76 86 106
2000 LB T 3,18 3,18 3,18 3,18 3,18 3,68 3,89 4,01 4,27 5,61 5,99 6,55
App Wt 0,12 0,12 0,18 0,29 0,39 0,55 0,93 1,30 1,80 3,00 5,50 14,00
Kg
B 22 25 33 38 46 56 62 75 84 102 121 152
C 21 25 28 33 38 44 51 60 64 83 95 114
3000 LB T 3,18 3,30 3,51 4,09 4,32 4,98 5,28 5,56 7,14 7,65 8,84 11,18
App Wt 0,21 0,21 0,31 0,49 0,80 1,31 1,61 3,20 3,55 6,50 9,25 17,00
Kg
B 25 33 38 46 56 62 75 84 102 121 146 152
6000 LB C 25 28 33 38 44 51 60 64 83 95 106 114
T 6,35 6,60 6,98 8,15 8,53 9,93 10,59 11,07 12,09 15,29 16,64 18,67
App Wt 0,41 0,41 0,60 0,94 1,59 2,14 3,39 4,50 10,00 13,00 19,50 18,00
Kg
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
B 22 22 25 33 38 46 56 62 75 92 109 146
C 21 21 25 28 33 38 44 51 60 76 86 106
2000 LB T 3,18 3,18 3,18 3,18 3,18 3,68 3,89 4,01 4,27 5,61 5,99 6,55
App Wt 0,14 0,14 0,19 0,34 0,42 0,75 1,15 1,45 2,25 4,50 7,15 15,00
Kg
B 22 25 33 38 46 56 62 75 84 102 121 152
C 21 25 28 33 38 44 51 60 64 83 95 114
3000 LB T 3,18 3,30 3,51 4,09 4,32 4,98 5,28 5,56 7,14 7,65 8,84 11,18
App Wt 0,22 0,22 0,40 0,63 0,99 1,63 1,97 3,70 4,90 10,50 11,50 21,70
Kg
B 25 33 38 46 56 62 75 84 102 121 146 152
C 25 28 33 38 44 51 60 64 83 95 106 114
6000 LB T 6,35 6,60 6,98 8,15 8,53 9,93 10,59 11,07 12,09 15,29 16,64 18,67
App Wt 0,45 0,45 0,70 1,16 1,80 2,50 4,10 5,20 12,30 14,00 25,00 23,00
Kg
84 ahlsell
FORGeD steeL FIttINGs tHReADeD
Caps
Half Couplings
Couplings Equal & Reducing
COUPLINGS - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 16 19 22 28 35 44 57 64 76 92 108 140
3000 LB B 32 35 38 48 51 60 67 79 86 92 108 121
App Wt 0,05 0,05 0,06 0,14 0,20 0,39 0,73 1,03 1,35 2,30 3,15 5,80
Kg
A 22 25 32 38 44 57 64 76 92 108 127 159
6000 LB B 32 35 38 48 51 60 67 79 86 92 108 121
App Wt 0,10 0,10 0,12 0,37 0,45 1,00 1,65 1,85 2,80 4,00 5,50 10,00
Kg
HALF COUPLINGS - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 16 19 22 28 35 44 57 64 76 92 108 140
3000 LB B 16,0 17,5 19,0 24,0 25,5 30,0 33,5 39,5 43,0 46,0 54,0 60,5
Appt Wt 0,02 0,03 0,03 0,07 0,11 0,20 0,37 0,51 0,66 1,15 1,57 2,90
Kg
A 22 25 32 38 44 57 64 76 92 108 127 159
6000 LB B 16,0 17,5 19,0 24,0 25,5 30,0 33,5 39,5 43,0 46,0 54,0 60,5
App Wt 0,04 0,05 0,06 0,19 0,23 0,50 0,83 0,92 1,40 2,00 2,75 5,00
Kg
CAPS - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 16 19 22 28 35 44 57 64 76 92 108 140 3000 LB B 19,0 25,0 25,0 32,0 37,0 41,0 44,0 44,0 48 60,0 65,0 68,0 T 4,8 4,8 4,8 6,4 6,4 9,7 9,7 11,2 12,7 15,7 19,0 22,4 Appt Wt 0,04 0,05 0,06 0,13 0,21 0,37 0,60 0,73 1,10 2,31 3,00 4,50 Kg
A 25 32 38 44 57 64 76 92 108 127 159 6000 LB B 27,0 27,0 33,0 38,0 43,0 46,0 48,0 51,0 64,0 68,0 75,0 T 6,4 6,4 7,9 7,9 11,2 11,2 12,7 15,7 19,0 22,4 28,4 App Wt 0,16 0,20 0,29 0,40 0,70 1,10 1,35 2,10 3,50 4,80 7,50
Kg
ahlsell 85
tHReADeD FORGeD steeL FIttINGs
Square Head
Welding Boss
STREET ELBOWS - MALE/ FEMALE - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2”
B 19 25 32 38 44 51 62 70 84
C 19 22 25 28 35 44 51 64 64
3000 LB T 3,18 3,30 3,51 4,09 4,32 4,98 5,28 5,56 7,14
App Wt 0,13 0,23 0,33 0,53 0,94 1,30 1,47 2,30
Kg
B 25 32 38 44 51 62 70 84 102
C 22 25 28 35 44 51 54 64 83
6000 LB T 5,08 5,66 6,98 8,15 8,53 9,93 10,59 11,07 12,09
App Wt
Kg
WELDING BOSS - THREADED - BS3799
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄2” 2”
A 38 41 45 51 51 51 51 51
3000 LB B 16 19 22 29 35 45 64 76
6000 LB B 22 26 32 38 45 60 76 95
App Wt 0,20 0,24 0,30 0,37 0,50 0,80 1,29 1,78
Kg (6000lb)
SQUARE HEAD PLUG (ASME B16.11)
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 10 11 13 14 16 19 21 21 22 27 28 32
3000 LB B 6 6 8 10 11 13 14 16 18 19 21 25
+ C 7 10 11 14 16 21 24 28 32 36 41 65
6000 LB App Wt 0,01 0,02 0,03 0,05 0,09 0,17 0,27 0,40 0,60 0,89 1,25 3,10
Kg
NOTE: At manufacturer option, the dimensions C of the table for threaded Tees (previous page) may be used instead of C in above table
86 ahlsell
FORGeD steeL FIttINGs tHReADeD
PIPE NIPPLES - THREADED - BS3799
1/8” 1/4” 3/8” 1/2” 3/4” 1” 11⁄4” 11⁄2” 2” 2 1⁄2” 3” 4”
Length ‘L’ 100 mm is our standard, but any length will be provided on request.
Pipe wall: Available in any standard Schedule, e.g. Sch80 -3000 lb, SchXXS - 6000 lb.
End Types Threaded, bevelled or plain.
3000lbs - XS 0,07 0,08 0,11 0,16 0,22 0,31 0,44 0,53 0,74 1,12 1,46 2,15
6000lbs - XXS 0,25 0,36 0,54 0,77 0,95 1,31 2,00 2,65 4,00
NOTE: The 6000 lbs is typical manufacturer standard - not included in BS3799
A
B - at flats
A
ROUND HEAD PLUG - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
3000 LB A 10 11 13 14 16 19 21 21 22 27 28 32
D 35 41 41 44 44 51 51 51 64 70 70 76
+ E 10 14 18 21 27 33 43 48 60 73 89 114
6000 LB App Wt 0,04 0,05 0,07 0,13 0,22 0,32 0,50 0,72 1,35 2,20 3,30 6,00
Kg
HEXAGON HEAD PLUG - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
3000 LB A 10 11 13 14 16 19 21 21 22 27 28 32
+ H 6 6 8 8 10 10 14 16 18 19 21 25
6000 LB F 11 16 18 22 27 36 46 50 65 75 90 115
App Wt 0,02 0,03 0,05 0,07 0,13 0,22 0,41 0,49 0,77 1,61 1,94 4,50
Kg
UNIONS - THREADED - BS3799 (1974)
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 40 43 48 51 57 64 70 79 89 118 121 -
B 32 32 36 43 50 60 70 78 95 125 140 -
3000 LB C 16 18 19 21 24 25 29 30 37 48 51 -
D 17 19 22 30 36 41 50 60 70 85 100 -
App Wt 0,14 0,17 0,21 0,31 0,49 0,83 1,22 1,53 2,30 5,00 6,25 -
Kg
A 44,5 44,5 50,8 60,5 57,2 57,2 76,2 88,9 108,0 108,0 127,0 -
B 39,6 39,6 42,9 53,8 58,4 73,2 79,2 88,9 120,7 152,4 190,5 -
6000 LB C 22,4 22,4 26,9 26,9 26,9 34,8 34,8 34,8 47,8 53,8 50,8 -
D 23,9 23,9 31,8 36,6 44,5 55,6 63,5 76,2 88,9 108,0 127,0 -
App Wt 0,20 0,30 0,50 1,12 1,60 2,15 2,42 4,73 6,50 9,50 19,20 -
ahlsell 87
tHReADeD FORGeD steeL FIttINGs
H - At FLAts
UNIONS - MALE X FEMALE (MF), THREADED X 2,THREADED + SOCKET WELDED
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2”
A 49,5 54,1 60,7 65,0 72,6 83,1 90,7 99,6 111,3
B 32,0 32,0 36,1 42,9 50,0 59,9 70,1 78,0 95,0
3000 LB C 16,0 18,0 19,1 21,1 23,9 24,9 29,0 30,0 37,1
D 17,0 19,1 22,1 30,0 36,1 40,9 50,0 59,9 70,1
App Wt 0,16 0,21 0,27 0,46 0,61 0,99 1,55 1,9 2,9 Kg
HEXAGON HEAD BUSHING - THREADED - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A – 11 13 14 16 19 21 21 22 27 28 32
3000 LB B – 3 4 5 6 6 7 8 9 10 10 13
+ F – 16 18 22 27 36 46 50 65 75 90 115
6000 LB Av App – 0,02 0,03 0,06 0,10 0,17 0,33 0,42 0,62 1,27 1,65 3,10
Wt Kg
HEXAGON NIPPLES - THREADED - BS3799
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄2” 2”
B 6 6 8 8 10 10 16 17
BS3799 (min) C 10 15 16 20 21 25 26 27
3000 LB D 5 8 11 14 19 24 38 49
6000 LB D 2 6 8 11 13 17 30 39
H 11 15 18 22 27 35 50 62
App Wt 0,02 0,03 0,06 0,08 0,15 0,24 0,37 0,45
Kg
CLOSE TAPER NIPPLES
Available in any Standard Production ScheduleWall Thickness, e.g. Sch 40, 80, 160, XXS
1⁄ 8 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
Standard 19,1 25,4 28,6 31,8 38,1 44,5 50,8 50,8 50,8 60,3 76,2 88,9 ‘L’ Length
NOTE: Reducing sizes is also available, but not included in above table
88 ahlsell
FORGeD steeL FIttINGs tHReADeD/sOCKet WeLD
SWAGED NIPPLES
90° elbow
Large end 3/8” 1/2” 3/4” 1” 1 1⁄2” 2” 2 1⁄2” 3” 4” dimensions
Length 76 89 95 102 114 165 178 203 229
90°ELBOWS - SOCKET WELD - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 11,0 11,0 13,5 15,5 19,0 22,5 27,0 32,0 38,0 41,0 57,0 66,5
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 73,9 89,8 115,2
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 74,4 90,3 115,7
3000 LB C min 3,18 3,30 3,50 4,09 4,27 4,98 5,28 5,54 6,04 7,67 8,30 9,35
D min 6,1 8,5 11,8 15,0 20,2 25,9 34,3 40,1 51,7 61,2 76,4 100,7
D max 7,6 10,0 13,3 16,6 21,7 27,4 35,8 41,6 53,3 64,2 79,4 103,8
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 16,0 16,0 16,0 16,0 19,0
App Wt 0,08 0,08 0,12 0,24 0,29 0,48 0,75 0,95 1,65 2,50 4,30 9,70
Kg
A 11,0 13,5 15,5 19,0 22,5 27,0 32,0 38,0 41,0 - - -
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 - - -
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 - - -
C min 3,43 4,01 4,37 5,18 6,04 6,93 6,93 7,80 9,50 - - -
D min 3,2 5,6 8,4 11,0 14,8 19,9 28,7 33,2 42,1 - - -
6000 LB E 4,8 7,1 9,9 12,5 16,3 21,5 30,2 34,7 43,6 - - -
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 - - -
App W 0,15 0,17 0,30 0,43 0,66 1,14 1,60 2,70 2,95 - - -
Kg
NOTE: 3000 lbs minimum from thickness Sch80, 6000 lbs from thickness Sch160 / XXS respectively for plain vs screwed
ahlsell 89
sOCKet WeLD FORGeD steeL FIttINGs
45°ELBOWS - SOCKET WELD - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 8,0 8,0 8,0 11,0 13,0 14,0 17,5 20,5 25,5 28,5 32,0 41,0
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 73,9 89,8 115,2
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 74,4 90,3 115,7
C min 3,18 3,30 3,50 4,09 4,27 4,98 5,28 5,54 6,04 7,67 8,30 9,35
3000 LB D min 6,1 8,5 11,8 15,0 20,2 25,9 34,3 40,1 51,7 61,2 76,4 100,7
D max 7,6 10,0 13,3 16,6 21,7 27,4 35,8 41,6 53,3 64,2 79,4 103,8
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 16,0 16,0 19,0
App Wt 0,08 0,08 0,10 0,19 0,38 0,38 0,58 0,83 1,15 2,05 3,40 9,00
Kg
A 8,0 8,0 11,0 12,5 14,0 17,5 20,5 25,5 28,5 - - -
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 - - -
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 - - -
C min 3,43 4,01 4,37 5,18 6,04 6,93 6,93 7,80 9,50 - - -
6000 LB D min 3,2 5,6 8,4 11,0 14,8 19,9 28,7 33,2 42,1 - - -
D max 4,8 7,1 9,9 12,5 16,3 21,5 30,2 34,7 43,6 - - -
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 - - -
App Wt 0,12 0,12 0,24 0,30 0,53 0,86 1,07 1,90 2,35 - - -
Kg
TEES - EQUAL & REDUCING - SOCKET WELD - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 11,0 11,0 13,5 15,5 19,0 22,5 27,0 32,0 38,0 41,0 57,0 66,5
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 73,9 89,8 115,2
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 74,4 90,3 115,7
3000 LB C min 3,18 3,30 3,50 4,09 4,27 4,98 5,28 5,54 6,04 7,67 8,30 9,35
D min 6,1 8,5 11,8 15,0 20,2 25,9 34,3 40,1 51,7 61,2 76,4 100,7
D max 7,6 10,0 13,3 16,6 21,7 27,4 35,8 41,6 53,3 64,2 79,4 103,8
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 16,0 16,0 19,0
App Wt 0,12 0,12 0,19 0,31 0,40 0,58 0,91 1,25 2,10 3,15 5,25 13,50
Kg
A 11,0 13,5 15,5 19,0 22,5 27,0 32,0 38,0 41,0 - - -
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 - - -
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 - - -
6000 LB C min 3,43 4,01 4,37 5,18 6,04 6,93 6,93 7,80 9,50 - - -
D min 3,2 5,6 8,4 11,0 14,8 19,9 28,7 33,2 42,1 - - -
D max 4,8 7,1 9,9 12,5 16,3 21,5 30,2 34,7 43,6 - - -
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 - - -
App Wt 0,21 0,21 0,40 0,56 0,91 1,41 1,75 3,56 4,10 - - -
Kg
90 ahlsell
FORGeD steeL FIttINGs sOCKet WeLD
CROSSES - SOCKET WELD - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 11,0 11,0 13,5 15,5 19,0 22,5 27,0 32,0 38,0 41,0 57,0 66,5
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 73,9 89,8 115,2
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 74,4 90,3 115,7
C min 3,18 3,30 3,50 4,09 4,27 4,98 5,28 5,54 6,04 7,67 8,30 9,35
3000 LB D min 6,1 8,5 11,8 15,0 20,2 25,9 34,3 40,1 51,7 61,2 76,4 100,7
D max 7,6 10,0 13,3 16,6 21,7 27,4 35,8 41,6 53,3 64,2 79,4 103,8
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 16,0 16,0 19,0
App Wt 0,14 0,14 0,21 0,34 0,47 0,80 1,25 1,50 2,23 3,95 6,50 16,00
Kg
A 11,0 13,5 15,5 19,0 22,5 27,0 32,0 38,0 41,0 - - -
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 - - -
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 - - -
C min 3,43 4,01 4,37 5,18 6,04 6,93 6,93 7,80 9,50 - - -
6000 LB D min 3,2 5,6 8,4 11,0 14,8 19,9 28,7 33,2 42,1 - - -
D max 4,8 7,1 9,9 12,5 16,3 21,5 30,2 34,7 43,6 - - -
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 - - -
App Wt 0,26 0,26 0,50 0,67 1,06 1,79 2,15 4,45 5,40 - - -
Kg
UNIONS - SOCKET WELD - BS3799
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 17 17 17 18 20 26 28 30 36 57 70
B 10,7 14,1 17,6 21,8 27,4 34,1 42,9 49,0 61,0 73,8 89,7
C 3,2 3,3 3,5 4,1 4,3 5,0 5,3 5,6 6,1 7,7 8,3
3000 LB D 6,8 9,2 12,5 15,5 21,0 26,5 35,0 40,5 52,0 62,0 78,0
E 3,2 3,2 3,2 4,0 4,8 4,8 5,6 5,6 6,4 9,6 12,7
F 32 32 36 41 50 60 70 78 95 125 140
S 10 10 10 10 13 13 13 13 16 16 16
App Wt 0,14 0,18 0,23 0,39 0,52 0,73 1,20 1,56 2,30 5,00 7,15
Kg
NOTE: 6000 lbs is available with manufacturer standard dimensions
ahlsell 91
sOCKet WeLD FORGeD steeL FIttINGs
Coupling
Half Coupling
Type 1
Type 2
Type 3
REDUCING INSERT 3000LB - SOCKET WELD
NB C D A B E F Type
1/2” x 3/8” 47,0 17,5 10,9 23,9 25,9 1 1/2” x 1/4” 47,0 14,0 9,4 16,0 2 3/4” x 1/2” 26,9 21,6 12,4 25,4 32,0 1 3/4” x 3/8” 26,9 17,5 10,9 14,0 2 3/4” x 1/4” 26,9 14,0 9,4 16,0 22,1 3 1” x 3/4” 33,5 27,2 14,5 28,4 38,1 1 1” x 1/2” 33,5 21,6 12,4 20,6 2 1” x 3/8” 33,5 16,5 10,9 22,1 25,9 3 1” x 1/4” 33,5 14,0 9,4 23,9 22,1 3 1 1⁄4” x 1” 42,4 33,8 16,0 32,0 45,0 1 1 1⁄4” x 3/4” 42,4 27,2 14,5 20,6 2 1 1⁄4” x 1/2” 42,4 21,6 12,4 22,1 32,0 3 1 1⁄4” x 1 1⁄4” 48,4 42,5 17,5 33,0 56,9 1 1 1⁄4” x 1” 48,4 33,8 16,0 20,6 2 1 1⁄2” x 3/4” 48,4 27,2 14,5 22,1 38,1 3 1 1⁄2” x 1/2” 48,4 21,6 12,4 24,1 32,0 3 2” x 1 1⁄2” 60,6 48,8 19,1 20,6 2 2” x 1 1⁄4” 60,6 42,7 17,5 22,1 56,9 3 2” x 1” 60,6 33,8 16,0 24,1 45,0 3 2” x 3/4” 60,6 27,2 14,5 25,4 38,1 3 2” x 1/2” 60,6 21,6 12,4 26,9 32,0 3
COUPLING & HALF COUPLING - SOCKET WELD - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
A 6,5 6,5 6,5 9,5 9,5 12,5 12,5 12,5 19,0 19,0 19,0 19,0
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 73,9 89,8 115,2
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 74,4 90,3 115,7
C min 3,18 3,30 3,50 4,09 4,27 4,98 5,28 5,54 6,04 7,67 8,30 9,35
3000 LB D min 6,1 8,5 11,8 15,0 20,2 25,9 34,3 40,1 51,7 61,2 76,4 100,7
D max 7,6 10,0 13,3 16,6 21,7 27,4 35,8 41,6 53,3 64,2 79,4 103,8
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 16,0 16,0 19,0
F 16,0 16,0 17,5 22,5 24,0 28,5 30,0 32,0 41,0 43,0 44,5 48,0
App Wt 0,05 0,05 0,07 0,11 0,15 0,26 0,37 0,42 0,77 1,10 1,40 2,35
Kg
A 6,5 6,5 6,5 9,5 9,5 12,5 12,5 12,5 19,0 - - -
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 - - -
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 - - -
C min 3,43 4,01 4,37 5,18 6,04 6,93 6,93 7,80 9,50 - - -
6000 LB D min 3,2 5,6 8,4 11,0 14,8 19,9 28,7 33,2 42,1 - - -
D max 4,8 7,1 9,9 12,5 16,3 21,5 30,2 34,7 43,6 - - -
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 - - -
F 16,0 16,0 17,5 22,5 24,0 28,5 30,0 32,0 41,0 - - -
App Wt 0,07 0,07 0,10 0,15 0,34 0,37 0,49 0,68 1,24 - - -
Kg
92 ahlsell
FORGeD steeL FIttINGs sOCKet WeLD
Welding Boss
CAPS -SOCKET WELD - B16.11
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 73,9 89,8 115,2
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 74,4 90,3 115,7
3000 LB C min 3,18 3,30 3,50 4,09 4,27 4,98 5,28 5,54 6,04 7,67 8,30 9,35
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 16,0 16,0 19,0
H 4,8 4,8 4,8 6,4 6,4 9,6 9,6 11,2 12,7 15,7 19,0 22,4
App Wt 0,03 0,04 0,06 0,14 0,18 0,30 0,51 0,65 0,92 1,40 2,50 3,50 Kg
B min 10,8 14,2 17,6 21,8 27,2 33,9 42,7 48,8 61,2 - - -
B max 11,2 14,6 18,0 22,2 27,6 34,3 43,1 49,2 61,7 - - -
6000 LB C min 3,43 4,01 4,37 5,18 6,04 6,93 6,93 7,80 9,50 - - -
E 9,5 9,5 9,5 9,5 12,5 12,5 12,5 12,5 16,0 - - -
H 6,4 6,4 6,4 7,9 7,9 11,2 11,2 12,7 15,7 - - -
App Wt 0,08 0,08 0,14 0,18 0,21 0,46 0,70 0,89 1,20 - - -
Kg
WELDING BOSS - SOCKET WELD .- BS3799
Rating Dims 1/8” 1/4” 3/8” 1/2” 3/4” 1 1 1⁄2” 2”
B 10,7 14,1 17,6 21,8 27,4 34,1 49,0 61,0
3000 LB C 3,2 3,3 3,5 4,1 4,3 5,0 5,6 6,1
6000 LB C - - - 5,2 6,1 7,0 7,8 9,5
D THROUGH BORE, Sch 40 - 3000 lb, Sch 160 - 6000 lb
F 28,0 32 34 38 38 35 32 29
S 10 10 11 13 13 16 19 22
App Wt 0,20 0,23 0,29 0,38 0,53 0,83 1,31 1,86
Kg
ahlsell 93
tHReADs FORGeD steeL FIttINGs
TAPER PIPE THREADS, NPT
Diameter of Diameter of Nomi- Outside Num- the pitch of the pitch of Efficient Length Increase nal diameter ber Pitch the bolt at the bolt at length of the of the size of the of the outside the inside of the hand diameter of tube threads end of the end of the thread packing per rotation tube per thread thread D inch P Eo E1 L2 L1
mm In. mm In. mm In. mm In. mm In. mm In. mm In.
1 ⁄ 8 10,29 0,405 27 0,94 0,03704 9,233 0,36351 9,489 0,3736 6,703 0,2639 4,102 0,1615 0,0586 0,00231
1 ⁄ 4 13,72 0,54 18 1,411 0,05556 12,126 0,47739 12,487 0,49163 10,205 0,4018 5,786 0,2278 0,0881 0,00347
3 ⁄ 8 17,14 0,675 18 1,411 0,05556 15,545 0,61201 15,929 0,62701 10,358 0,4078 6,096 0,24 0,0881 0,00347
1 ⁄ 2 21,34 0,84 14 1,814 0,07143 19,264 0,75843 19,772 0,77843 13,556 0,5337 8,128 0,32 0,1132 0,00446
3 ⁄ 4 26,67 1,05 14 1,814 0,07143 24,579 0,96768 25,117 0,98887 13,86 0,5457 8,61 0,339 0,1132 0,00446
1 33,4 1,315 11 1⁄2 2,209 0,08696 30,826 1,21363 31,461 1,23863 17,343 0,6828 10,16 0,4 0,1379 0,00543
1 1⁄4 42,16 1,66 11 1⁄2 2,209 0,08696 39,551 1,55713 40,218 1,58338 17,952 0,7068 10,668 0,42 0,1379 0,00543
1 1⁄2 48,26 1,9 11 1⁄2 2,209 0,08696 45,621 1,79609 46,287 1,82234 18,377 0,7235 10,668 0,42 0,1379 0,00543
2 60,32 2,375 11 1⁄2 2,209 0,08696 57,633 2,26902 58,325 2,29627 19,215 0,7565 11,074 0,436 0,1379 0,00543
2 1⁄2 73,02 2,875 8 3,175 0,125 69,076 2,71953 70,159 2,76216 28,892 1,1375 17,322 0,682 0,1983 0,00781
3 88,9 3,5 8 3,175 0,125 84,852 3,34062 86,068 3,3885 30,48 1,2 19,456 0,766 0,1983 0,00781
3 1⁄2 101,6 4 8 3,175 0,125 97,472 3,8375 98,776 3,88881 31,75 1,25 20,853 0,821 0,1983 0,00781
4 114,3 4,5 8 3,175 0,125 110,093 4,33438 111,433 4,38712 33,02 1,3 21,437 0,844 0,1983 0,00781
NOTE: All sizes in the table correspond to the ASME B1.20.1 and API 5 L Standards, excepted for the nominal sizes 1/8’’ and 1/4’’ for which E1 and L1 are not measured on the same plane according to API 5L. However, these sizes are the same when brought on the same plane.
94 ahlsell
O-LE
TS
O-Lets
ahlsell 95
96 ahlsell
O-Lets
BRANCH OUTLETS – O´LETS.
BASIS FOR DESIGN OF O´LETS:
MANUFACTURER STANDARD:The O´lets in this catalogue are based on a single manufacturer’s standard design and denominations. The standard design is based on ASME B31.3, but O´lets may be designed, manufactured and verified to other requirements at the client’s request.
HEIGHT STANDARDISATION:The table-listed heights (A) of reducing weldolets – buttweld, socket weld and threaded outlets – are identical to the heights standardised in MSS SP-97, except the 3000lbs socket weld outlets in sizes 2 ½” – 4”. However, it should be noted that the height stated as standard may have to be changed due to the actual/ specific design required for specific size/ wall thickness combinations.
DESIGN OPTIMISATION:O´lets may be designed and manufactured to the customer’s specific design requirements,i.e. O´lets can be designed design to specific design parameters (e.g. PCS) and/ or Norsok EDS NOL1 so as to reduce the welding required in the crotch area.
DESIGN vERIFICATION:Drawings and calculations for each individual O´let may be provided, if requested by the client at the enquiry stage.
DIMENSION UNIFICATION:O´lets may also be designed to fit a range of run header dimensions – i.e., each O´let will be suitable for use on various header pipe sizes. This design will, however, require more welding during fabrication, as the O´let dimensions cannot be optimised to a specific size and the actual design parameters.
TYPES OF O´LETS
• Buttweld Outlet (O´let) – Butt welded / Socket Welded / Threaded
• Elbow Outlet – Butt welded / Socket Welded / Threaded
• Lateral Outlet – Butt welded / Socket Welded / Threaded
• Nipple Outlet – Butt welded / Threaded / Plain end
• Insert Branch Outlet
• Flanged Buttweld Outlet
• Flanged Nipple Outlet
DESIGN DETAILS REQUIRED FOR OPTIMISATION OF O´LETS:
• Design code
• Design pressure & rating
• Design temperature
• Material grade / allowable stress
• Wall thickness – for header and branch pipes
• Corrosion allowance
• Wall thickness tolerance
ahlsell 97
O-Lets
Ready to WeldEvery fitting is shaped to fit the pipe and it self-aligning.
«Space» for Welding The Weldolet is raised off run pipe to establish proper weld gap by placing spacers, e.g. wel-ding rods, under the fitting. This provides a uniform welding gap between the curvature of the run and base of fitting.
Longitudinal SectionFig. 1
Wide bases or footings at crotch sec-tion distribute internal and external stresses. Gradual changes of section eliminate stress concentration. Funnel shaped opening provides improved flow conditions. The outlet is machine bevelled for quick easy
butt-welding of the branch pipe for shop or field fabrication.
Tack Weld The base joint is tack wel-ded, prefer ably at four points, each half way between the crotch and skirt sec-tions of the fitting. The spacers are then removed.
Transverse SectionFig. 2
Note the blending of the skirt section of the Weldolet to the run pipe to avoid abrupt change in intersection. Throat of weld at this point is designated by the welding bevel.
Layout The template is the inside of the fitting. Cut Hole The hole in the run pipe on reducing sizes can be cut out either before or after the fitting is welded on.
The hole can be cut with a torch, a drill or a hole saw. Welding the fitting to the run pipe prior to cutting the hole helps prevent distortion on the run and can be done generally on outlet sizes over two inches.
Stringer Bead The stringer bead is applied completely around the base of the fitting. The established weld gap ensures full penetration.
Reinforcing Beads Reinforcing welds should be made at the crotch bevel areas of the fitting to provide maximum weld at the crotchtapering to minimu at the skirt. Particular care should be taken to weld only the bevel portion of the fitting. (See «weld lines» on above drawing)
This eliminates the unnecessary use of continuous passes and prevents the erroneous practice of welding up to the rib on the skirt portion of the fitting. A continuous cover bead should be added to fill the bevel and provide a smooth tapered weld.
EXAMPLE OF WELD SEQUENCE
98 ahlsell
O-Lets
DIMENSIONS UNIFICATIONIn order to reduce warehouse inventory, our outlets have been unified to fit on different run-pipe sizes with gap maximum of 1/32” between the run-pipe and outlet. This does not cause any problems during welding.
BUTTWELD-OUTLETS, STANDARD AND EXTRA STRONG, SOCKET-OUTLETS & THREADED-OUTLETS 3000LBS.
OUTLET SIzE RUN–PIPE SIzES 1 ⁄ 2 1 ⁄ 2 3 ⁄ 4 1 1 1⁄2–1 1⁄4 2 1⁄2–2 8–3 36–10 3 ⁄ 4 3 ⁄ 4 1 1 1⁄2 –11⁄4 2 1⁄2–2 5–3 12–6 36–14 1 1 1 1⁄4 1 1⁄2 2 2 1⁄2 3 1⁄2 –3 5–4 10–6 36–12 1 1⁄4 1 1⁄4 1 1⁄2 2 2 1 ⁄2 3 1⁄2–3 5–4 8–6 18–10 36–20 1 1⁄2 1 1⁄2 2 2 1⁄2 3 4–3 1⁄2 6–5 12–8 24–14 36–26 2 2 2 1⁄2 3 3 1⁄2 4 5 6 10–8 18–12 36–20 2 1⁄2 2 1⁄2 3 3 1⁄2 4 5 6 8 12–10 18–14 36–20 3 3 3 1⁄2 4 5 6 8 10 14–12 20–16 36–24 3 1⁄2 3 1⁄2 4 5 6 8 10 14–12 20–16 36–24 4 4 5 6 8 10 14–12 20–16 36–24
BUTTWELD-OUTLETS SCH. 160 AND XXS OUTLET SIzE RUN – PIPE SIzES
1 ⁄ 2 1 ⁄ 2 1 1⁄4 – 3⁄4 36 – 1 1⁄2 3 ⁄ 4 1 – 3⁄4 2 – 1 1⁄4 6 – 2 1⁄2 36 – 8 1 1 2 1⁄2 – 1 1⁄4 10 – 3 36 – 12 1 1⁄4 1 1⁄2 – 1 1⁄4 2 1⁄2 – 2 10 – 3 36 – 12 1 1⁄2 1 1⁄2 2 1⁄2 – 2 3 1⁄2 – 3 8 – 4 20 – 10 36 – 24 2 2 2 1⁄2 3 1⁄2 – 3 5 – 4 8 – 6 18 – 10 36 – 20 Outlet over 2” order to specific run-pipe size
BUTTWELD-OUTLETS & THREADED-OUTLETS 6000LBS. OUTLET SIzE RUN – PIPE SIzES
1 ⁄ 2 1 – 3 ⁄ 4 2 – 1 1⁄4 6 – 2 1⁄2 36 – 8 3 ⁄ 4 1 2 1⁄2 – 1 1⁄4 10 – 3 36 – 12 1 1 1⁄4 – 1 1⁄2 2 1⁄2 – 2 10 – 3 36 – 12 1 1⁄4 1 1⁄2 2 1⁄2 – 2 3 1⁄2 – 3 8 – 4 20 – 10 36 – 24 1 1⁄2 2 2 1⁄2 3 1⁄2 – 3 5 – 4 8 – 6 18 – 10 36 – 20 2 2 1⁄2 3 4 5 6 10 – 8 20 – 12 36 – 24
Outlet over 4” order to specific run-pipe size
ahlsell 99
O-Lets
BUTTWELD OUTLETS - EXTRA STRONG
BUTTWELD OUTLETS - STANDARD
REDUCED SIzES FULL SIzES
OUTLET SIzE A C Approx. A C D Approx. [inch] [mm] [mm] Weight [mm] [mm] [mm] Weight
1/2 19,0 24,0 0,1 19,0 24,0 15,8 0,1
3/4 22,2 30,0 0,1 22,2 30,0 21,0 0,1
1 27,0 36,5 0,3 27,0 36,5 26,6 0,2
1 1⁄4 31,5 44,5 0,4 31,5 44,5 35,0 0,3
1 1⁄2 33,4 51,0 0,5 33,4 51,0 40,9 0,4
2 38,0 65,0 0,8 38,0 65,0 52,5 0,7
2 1⁄2 41,2 76,2 1,1 41,2 76,2 62,8 1,0
3 44,5 93,5 1,8 44,5 93,5 78,0 1,7
3 1⁄2 47,5 112,6 2,5 47,5 112,6 90,2 2,3
4 51,0 120,5 2,9 51,0 120,5 102,2 3,1
5 57,0 141,3 4,7 57,0 141,3 128,2 3,9
6 60,3 170,0 6,5 60,3 170,0 154,0 6,7
8 69,8 220,5 10,7 69,8 220,5 202,5 13,0
10 78,0 274,0 18,0 78,0 274,0 254,0 16,0
12 86,0 324,0 27,0 86,0 324,0 304,5 27,0
14 89,0 356,0 30,0 89,0 356,0 336,5 32,0
REDUCED SIzES FULL SIzES
OUTLET SIzE A C Approx. A C D Approx. [inch] [mm] [mm] Weight [mm] [mm] [mm] Weight
1 ⁄ 2 19,0 24,0 0,1 19,0 24,0 13,9 0,1
3 ⁄ 4 22,2 30,0 0,1 22,2 30,0 18,9 0,1
1 27,0 36,5 0,2 25,4 36,5 24,3 0,2
1 1⁄4 31,5 44,5 0,4 28,5 44,5 32,8 0,3
1 1⁄2 33,4 51,0 0,5 31,5 51,0 38,1 0,4
2 38,0 65,0 0,8 38,0 65,0 49,3 0,8
2 1⁄2 41,2 76,2 1,2 41,2 76,2 59,0 1,2
3 44,5 93,5 1,9 44,5 93,5 73,7 1,9
3 1⁄2 47,5 112,6 2,6 47,5 112,6 85,4 2,3
4 51,0 120,5 3,0 51,0 120,5 97,2 3,5
5 57,0 141,3 4,8 57,0 141,3 122,3 4,3
6 78,0 170,0 10,5 78,0 170,0 146,3 6,8
8 98,5 220,0 17,0 98,5 220,0 194,0 14,6
10 94,0 265,0 21,0 95,3 265,0 247,5 21,0
12 103,0 316,0 28,0 100,0 320,0 298,0 28,0
14 100,0 351,0 32,0 105,5 355,0 330,0 34,5
100 ahlsell
O-Lets
Socketweld outletS • 6000 lBS (Socket weld to ASMe/ANSI B 6.11)
Socketweld outletS • 3000 lBS (Socket weld to ASMe/ANSI B 16.11)
Buttweld outletS • ScH. 160 ANd XXS
REDUCED SIzES FULL SIzES
OUTLET SIzE A C Approx. A C Approx. [inch] [mm] [mm] Weight [mm] [mm] Weight
1 ⁄ 2 28,5 14,3 0,1 28,5 14,3 0,1 3 ⁄ 4 31,5 19,0 0,3 31,5 19,0 0,3 1 38,0 25,5 0,4 38,0 25,5 0,4 1 1⁄4 44,5 33,4 0,6 44,5 33,4 0,6 1 1⁄2 50,7 38,0 0,8 50,7 38,0 0,8 2 55,5 42,9 1,0 55,5 42,9 1,0 2 1⁄2 61,8 53,9 1,6 61,8 53,9 1,6 3 73,0 73,0 2,9 73,0 73,0 2,9 4 84,0 98,4 4,8 84,0 98,4 4,8 5 93,5 122,2 6,5 93,5 122,2 6,5 6 104,7 146,0 12,8 104,7 146,0 13,8
OUTLET REDUCED SIzES FULL SIzES SIzE A C F G Approx. A C D F G Approx. [inch] [mm] [mm] [mm] [mm] Weight [mm] [mm] [mm] [mm] [mm] Weight
1/2 25,5 24,0 31,8 10,0 0,1 25,5 22,4 16,0 31,8 10,0 0,1 3/4 27,0 30,0 36,6 13,0 0,2 27,0 30,0 21,0 36,6 13,0 0,1 1 33,4 36,5 46,1 13,0 0,3 33,4 36,5 26,7 46,1 13,0 0,3 1 1⁄4 33,4 44,5 55,6 13,0 0,4 33,4 44,5 35,0 55,6 13,0 0,3 1 1⁄2 34,8 51,0 62,0 13,0 0,5 34,8 51,0 40,9 62,0 13,0 0,4 2 38,0 65,0 74,7 16,0 0,7 38,0 65,0 52,5 74,7 16,0 0,6 2 1⁄2 46,0 76,2 87,4 16,0 1,3 46,0 76,2 62,8 87,4 16,0 1,0 3 50,7 93,5 104,8 16,0 1,7 50,7 93,5 77,9 104,8 16,0 1,7 3 1⁄2 53,8 101,5 122,3 19,0 2,0 53,3 112,8 90,1 117,5 19,0 2,0 4 57,0 120,5 130,2 19,0 3,3 55,5 127,0 102,2 130,2 19,0 3,0
OUTLET REDUCING SIzES
SIzE A C F G Approx.
[inch] [mm] [mm] [mm] [mm] Weight 1 ⁄ 2 31,5 19,0 40,0 10,0 0,3 3 ⁄ 4 36,5 25,5 46,0 13,0 0,4 1 39,6 33,4 57,2 13,0 0,6 1 1⁄4 41,0 38,0 65,1 13,0 0,8 1 1⁄2 42,7 49,3 76,3 13,0 0,9 2 52,1 70,0 92,1 16,0 2,4
ahlsell 101
O-Lets
tHreAded outletS • 6000 lBS
tHreAded outletS • 3000 lBS
OUTLET REDUCED SIzES FULL SIzES
SIzE A C F Approx. A C D F Approx. [inch] [mm] [mm] [mm] Weight [mm] [mm] [mm] [mm] Weight
1 ⁄ 2 25,5 24,0 31,8 0,1 25,5 24,0 16,0 3l,80 0,1 3 ⁄ 4 27,0 30,0 36,6 0,2 27,0 30,0 20,7 36,6 0,1 1 33,4 36,5 46,1 0,3 33,4 36,5 27,0 46,1 0,2 1 1⁄4 33,4 44,5 55,6 0,4 33,4 44,5 34,9 55,6 0,3 1 1⁄2 34,8 51,0 62,0 0,5 34,8 51,0 41,2 62,0 0,4 2 38,0 65,0 74,7 0,8 38,0 65,0 52,4 74,7 0,7 2 1⁄2 46,0 76,2 87,4 1,4 46,0 76,2 63,5 87,4 1,1 3 50,7 93,5 104,8 2,0 50,7 93,5 77,8 104,8 2,0 3 1⁄2 53,8 101,5 122,3 2,6 53,3 112,8 90,5 117,5 2,1 4 57,0 120,5 130,2 3,2 55,5 120,5 103,2 130,2 3,1
OUTLET REDUCING SIzES
SIzE A C F Approx. [inch] [mm] [mm] [mm] Weight
1 ⁄ 2 31,5 19,0 40,0 0,2 3 ⁄ 4 36,5 25,5 46,0 0,4 1 39,6 33,4 57,2 0,6 1 1⁄4 41,0 38,0 65,1 0,7 1 1⁄2 42,7 49,3 76,3 0,9 2 52,1 70,0 92,1 2,3
102 ahlsell
O-Lets
Dimensions for all three styles are the same except for the “D” dimension on the butt welding outletwhich matches the proper schedule on the branch pipe.
3000 LBS THREADED AND SOCKETWELD STANDARD AND EXTRA STRONG BUTT-WELD6000 LBS THREADED AND SOCKETWELD SCHEDULE 160 AND DOUBLE EXTRA STRONG BUTT-WELD
Elbow Outlet
Nominal Nominal Outlet DIMENSIONS WEIGHT
Elbow Size Elbow Size Size- 3000 lb 6000lb 3000 lb 6000lb 3000 lb 6000lb 3000 lb 6000lb (Inch) (Inch) Inches C C D D E E Approx. Wt. Approx.Wt. 3000 lb 6000 lb mm mm mm mm mm mm Kg. Kg.
36-1 1⁄4 36-1 1⁄4 1 ⁄ 4 38,1 38,1 31,8 31,8 38,1 38,1 0,23 0,34
36-1 1⁄4 36-1 1⁄4 3 ⁄ 8 38,1 38,1 31,8 31,8 38,1 38,1 0,23 0,34
36-1 1⁄4 36-1 1⁄4 1 ⁄ 2 38,1 43,6 31,8 35,7 38,1 45,2 0,30 0,39
36-1 1⁄4 36-2 3 ⁄ 4 43,6 54,0 35,7 45,2 45,2 54,4 0,34 0,57
36-2 36-2 1 54,0 73,0 45,2 54,8 52,4 55,6 0,52 1,00
36-2 36-2 1 1⁄4 73,0 79,4 54,8 63,5 55,6 58,8 0,86 1,77
36-2 36-3 1 1⁄2 79,4 106,4 63,5 82,6 58,8 69,9 1,20 2,80
36-3 - 2 106,4 - 82,6 - 69,9 - 2,39 -
ahlsell 103
O-Lets
Lateral Outlet
Dimensions for all three styles are the same except for the “D” dimension on the butt welding outlet which matches the proper schedule on the branch pipe.
3000 LBS THREADED AND SOCKETWELD STANDARD AND EXTRA STRONG BUTT-WELD
6000 LBS THREADED AND SOCKETWELD SCHEDULE 160 AND DOUBLE EXTRA STRONG
BUTT-WELD
Nominal Nominal Outlet DIMENSIONS WEIGHT Elbow Size Elbow Size Size- 3000 lb 6000lb 3000 lb 6000lb 3000 lb 6000lb 3000 lb 6000lb (Inch) (Inch) Inches C C D D E E Approx. Wt. Approx. Wt. 3000 lb 6000 lb (mm) (mm) (mm) (mm) (mm) (mm) Kg. Kg.
12 - 1 1⁄4 12 - 2 1⁄2 1 ⁄ 4 36,5 36,5 31,8 31,8 39,7 39,7 0,23 0,34
12 - 1 1⁄4 12 - 1 1⁄4 3 ⁄ 8 36,5 36,5 31,8 31,8 39,7 39,7 0,23 0,34
12 - 1 1⁄4 12 - 1 1⁄4 1 ⁄ 2 36,5 43,6 31,8 35,7 39,7 47,6 0,30 0,39
12 - 1 1⁄4 12 - 2 3 ⁄ 4 43,6 54 35,7 45,2 47,6 57,2 0,34 0,57
12 - 2 12 - 2 1 54 67,5 45,2 54,8 57,2 61,9 0,52 1,00
12 - 2 12 - 2 1 1⁄4 67,5 76,2 54,6 63,5 61,9 66,7 0,86 1,32
12 - 2 12 - 4 1 1⁄2 76,2 104,8 63,5 82,6 66,7 81,0 1,20 2,80
12 - 4 - 2 104,8 - 82,6 - 81 - 3,29 -
NOTE: Other Outlet sizes available on request.
104 ahlsell
O-Lets
FLANGED NIPPLE OUTLETSThe height (A) is 150mm for all sizes, except 2” 2500# that is 165mm.The bore (F) equals the nominal bore of the branch pipe.
FLANGED NIPPLE OUTLET - 150#
FLANGED NIPPLE OUTLET - 300#
FLANGED NIPPLE OUTLET - 600#
FLANGED NIPPLE OUTLET - 900# /1500#
FLANGED NIPPLE OUTLET - 2500#
Outlet
size B E C C Type
Std/XS 160/XXS 1
1/2 88,9 11,2 24,0 14,3 1 3/4 98,6 12,7 30,0 19,0 1 1 108,0 14,3 36,5 25,5 1 1 1⁄4 117,5 15,9 44,5 33,4 1 1 1⁄2 127,0 17,5 51,0 38,0 1 2 152,4 19,1 65,0 42,9 1
Outlet
size B E C C Type Type
Std/XS 160/XXS Std/XS 160/XXS
1/2 95,3 14,3 24,0 14,3 2 2 3/4 117,5 15,9 30,0 19,0 2 2 1 123,8 17,5 36,5 25,5 1 2 1 1⁄4 133,4 19,0 44,5 33,4 1 2 1 1⁄2 155,6 20,6 51,0 38,0 1 1 2 165,1 22,2 65,0 42,9 1 2
Outlet
size B E C C Type Type
Std/XS 160/XXS Std/XS 160/XXS
1/2 95,3 20,7 24,0 14,3 2 2 3/4 117,5 22,3 30,0 19,0 2 2 1 123,8 23,9 36,5 25,5 1 2 1 1⁄4 133,4 27,0 44,5 33,4 1 2 1 1⁄2 155,6 28,6 51,0 38,0 1 1 2 165,1 31,8 65,0 42,9 1 2
Outlet
size B E C C Type Type
Std/XS 160/XXS Std/XS 160/XXS
1/2 120,7 28,6 24,0 14,3 2 2 3/4 130,2 31,8 30,0 19,0 1 1 1 149,2 35,0 36,5 25,5 1 2 1 1⁄4 158,8 35,0 44,5 33,4 1 2 1 1⁄2 177,8 38,1 51,0 38,0 1 1 2 215,9 44,5 65,0 42,9 2 2
Outlet
size B E C C Type
Std/XS 160/XXS
1/2 133,4 36,6 24,0 14,3 2 3/4 139,7 38,1 30,0 19,0 2 1 158,8 41,3 36,5 25,5 2 1 1⁄4 184,2 44,5 44,5 33,4 2 1 1⁄2 203,2 50,8 51,0 38,0 2 2 235,0 57,2 65,0 42,9 2
ahlsell 105
O-Lets
FLANGED BUTTWELD OUTLETFlanged Buttweld Outlet is available also for larger sizes than listed below (up to 24” for 150# to 1500#). Flanged Buttweld Outlet is available in all pressure classes - below listed 150# and 2500# are typical - others available at request.
The dimensions below are based on RF type flanges. Other facings may be supplied at request. The C dimensions listed are based on Std wall for header and branch pipe. Any wall may be supplied at request. The bore (F) equals the nominal bore of the branch pipe.
FLANGED BUTTWELD OUTLET - 150# FLANGED BUTTWELD OUTLET - 2500# Outlet
size B E A C Type
1/2 88,9 11,2 65,0 24,0 1 3/4 98,6 12,7 75,0 30,0 1 1 108,0 14,3 85,0 36,5 1 1 1⁄4 117,5 15,9 90,0 44,5 1 1 1⁄2 127,0 17,5 95,0 51,0 1 2 152,4 19,1 105,0 65,0 1 2 1⁄2 177,8 22,3 112,0 76,2 1 3 190,5 23,8 115,0 93,5 1 3 1⁄2 215,9 23,8 120,0 112,6 1 4 228,6 23,8 130,0 120,5 1 5 254,0 23,8 146,0 141,3 1 6 279,4 25,4 150,0 170,0 1 8 342,9 28,6 175,0 220,5 1 10 406,4 30,2 180,0 274,0 1 12 482,6 31,8 200,0 324,0 1
Outlet
size B E A C Type
1/2 133,4 36,5 100,0 24,0 2 3/4 139,7 38,1 110,0 30,0 2 1 158,8 41,3 125,0 36,5 2 1 1⁄4 184,2 44,5 135,0 44,5 2 1 1⁄2 203,2 50,8 150,0 51,0 2 2 235,0 57,2 170,0 65,0 2 2 1⁄2 266,7 63,5 190,0 76,2 2 3 304,8 73,0 220,0 93,5 2 4 355,6 82,6 250,0 120,5 2 5 419,1 98,4 290,0 141,3 2 6 482,6 114,3 340,0 170,0 2 8 552,5 133,4 395,0 220,5 2 10 673,1 171,5 505,0 274,0 2 12 762,0 190,5 555,0 324,0 2
NIPPLE OUTLET - 3000 / 6000 LBAvailable with plain / bevel / threaded end
Outlet
size A C C 3000 lb 6000lb
1/2 89,0 24,0 14,5
3/4 89,0 30,0 19,0
1 89,0 36,5 25,5
1 1⁄4 89,0 44,5 33,4
1 1⁄2 89,0 51,0 38,0
2 89,0 65,0 43,0
106 ahlsell
INSERT BRANCH OUTLETInsert Branch Outlets are available for any header wall thickness. The below dimensions are applicable for header wall thickness up to and including XS.
O-Lets
Outlet size A Min. header pipe size
1/2 32,0 1 1⁄2
3/4 32,0 2
1 32,0 2
1 1⁄4 32,0 2 Other dimensions
1 1⁄2 38,0 2 1⁄2 available at
2 44,0 3 specific request
3 51,0 4
4 60,0 6
6 68,0 8
8 76,0 10
10 79,0 12
12 86,0 16
14 92,0 18
16 95,0 20
18 117,0 22
20 130,0 24
24 143,0 30
ahlsell 107
108 ahlsell
ahlsell 109
WE
IGH
TS
WeIGHts
110 ahlsell
WeIGHt OF FIttINGs
SCREWED FITTINGS - B16.11 / BS3799
NOTE: All weights listed in this section are approximate weights for steel. Titanium weights can be calculated as 57% of table values. All weights are given in kilograms (kg)
PRODUCT RATING 1 ⁄ 8” 1 ⁄ 4” 3 ⁄ 8” 1 ⁄ 2” 3 ⁄ 4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
90° elbows 2000 lbs 0,08 0,08 0,11 0,23 0,28 0,46 0,80 1,00 1,60 2,30 4,35 10,25
3000 lbs 0,14 0,14 0,27 0,37 0,60 1,08 1,22 2,45 2,50 5,25 7,40 13,00
6000 lbs 0,31 0,31 0,50 0,69 1,25 1,65 2,75 3,22 6,25 10,00 17,00 18,00
45° elbows 2000 lbs 0,10 0,10 0,11 0,21 0,24 0,39 0,70 0,85 1,23 3,00 3,50 9,00
3000 lbs 0,13 0,13 0,25 0,36 0,53 0,78 1,02 1,70 2,35 5,40 6,00 10,50
6000 lbs 0,25 0,25 0,35 0,60 0,95 1,22 1,35 2,55 5,60 8,00 15,50 13,00
Tees 2000 lbs 0,12 0,12 0,18 0,29 0,39 0,55 0,93 1,30 1,80 3,00 5,50 14,00
3000 lbs 0,21 0,21 0,31 0,49 0,80 1,31 1,61 3,20 3,55 6,50 9,25 17,00
6000 lbs 0,41 0,41 0,60 0,94 1,59 2,14 3,39 4,50 10,00 13,00 19,50 18,00
Crosses 2000 lbs 0,14 0,14 0,19 0,34 0,42 0,75 1,15 1,45 2,25 4,50 7,15 15,00
3000 lbs 0,22 0,22 0,40 0,63 0,99 1,63 1,97 3,70 4,90 10,50 11,50 21,70
6000 lbs 0,45 0,45 0,70 1,16 1,80 2,50 4,10 5,20 12,30 14,00 25,00 23,00
Couplings 3000 lbs 0,05 0,05 0,06 0,14 0,20 0,39 0,73 1,03 1,35 2,30 3,15 5,80
6000 lbs 0,10 0,10 0,12 0,37 0,45 1,00 1,65 1,85 2,80 4,00 5,50 10,00
Half couplings 3000 lbs 0,02 0,03 0,03 0,07 0,11 0,20 0,37 0,51 0,66 1,15 1,57 2,90
6000 lbs 0,04 0,05 0,06 0,19 0,23 0,50 0,83 0,92 1,40 2,00 2,75 5,00
Caps 3000 lbs 0,04 0,05 0,06 0,13 0,21 0,37 0,60 0,73 1,10 2,31 3,00 4,50
6000 lbs - 0,16 0,20 0,29 0,40 0,70 1,10 1,35 2,10 3,50 4,80 7,50
Street elbows 3000 lbs - 0,13 0,23 0,33 0,53 0,94 1,30 1,47 2,30 - - -
Welding boss 0,20 0,23 0,29 0,38 0,53 0,83 1,31 1,86 - - - -
Pipe nipple - 100mm 3000 (XS) 0,07 0,08 0,11 0,16 0,22 0,31 0,44 0,53 0,74 1,12 1,46 2,15
6000 (XXS) - - - 0,25 0,36 0,54 0,77 0,95 1,31 2,00 2,65 4,00
Plug - square head 0,01 0,02 0,03 0,05 0,09 0,17 0,27 0,40 0,60 0,89 1,25 3,10
Plug - round head 0,04 0,05 0,07 0,13 0,22 0,32 0,50 0,72 1,35 2,20 3,30 6,00
Plug - hex. head 0,02 0,03 0,05 0,07 0,13 0,22 0,41 0,49 0,77 1,61 1,94 4,50
Unions - FF 3000 lbs 0,14 0,17 0,21 0,31 0,49 0,83 1,22 1,53 2,30 5,00 6,25 -
6000 lbs 0,20 0,30 0,50 1,12 1,60 2,15 2,42 4,73 6,50 9,50 19,20 -
Unions - MF 3000 lbs 0,16 0,21 0,27 0,46 0,61 0,99 1,55 1,9 2,9 - - -
Hex. head bushing - 0,02 0,03 0,06 0,10 0,17 0,33 0,42 0,62 1,27 1,65 3,10
Hex. Nipples 0,02 0,03 0,06 0,08 0,15 0,24 0,37 0,45 - - - -
Swage nipples 3000 lbs 0,04 0,05 0,09 0,14 0,17 0,32 0,49 0,60 0,93 - - -
plain 6000 lbs 0,11 0,13 0,18 0,23 0,29 0,55 0,80 1,10 1,40 - - -
screwed 6000 lbs 0,17 0,22 0,29 0,33 0,50 0,75 0,95 1,60 2,10 - - -
PIPES B36.10 / B36.19Weights are given in tables in section 2 of this catalogue.
ahlsell 111
WeIGHt OF FIttINGs
SOCKET WELD FITTINGS - B16.11 / BS3799
PRODUCT RATING 1 ⁄ 8” 1 ⁄ 4” 3 ⁄ 8” 1 ⁄ 2” 3 ⁄ 4” 1” 1 1⁄4” 1 1⁄2” 2” 2 1⁄2” 3” 4”
90° elbows 3000 lbs 0,08 0,08 0,12 0,24 0,29 0,48 0,75 0,95 1,65 2,50 4,30 9,70
6000 lbs 0,15 0,17 0,30 0,43 0,66 1,14 1,60 2,70 2,95 - - -
45° elbows 3000 lbs 0,08 0,08 0,10 0,19 0,25 0,38 0,58 0,83 1,15 2,05 3,40 9,00
6000 lbs 0,12 0,12 0,24 0,30 0,53 0,86 1,07 1,90 2,35 - - -
Tees 3000 lbs 0,12 0,12 0,19 0,31 0,40 0,58 0,91 1,25 2,10 3,15 5,25 13,50
6000 lbs 0,21 0,21 0,40 0,56 0,91 1,41 1,75 3,56 4,10 - - -
Crosses 3000 lbs 0,14 0,14 0,21 0,34 0,47 0,80 1,25 1,50 2,23 3,95 6,50 16,00
6000 lbs 0,26 0,26 0,50 0,67 1,06 1,79 2,15 4,45 5,40 - - -
Unions 3000 lbs 0,14 0,18 0,23 0,39 0,52 0,73 1,20 1,56 2,30 5,00 7,15 -
Couplings 3000 lbs 0,05 0,05 0,07 0,11 0,15 0,26 0,37 0,42 0,77 1,10 1,40 2,35
6000 lbs 0,07 0,07 0,10 0,15 0,34 0,37 0,49 0,68 1,24 - - -
Caps 3000 lbs 0,03 0,04 0,06 0,14 0,18 0,30 0,51 0,65 0,92 1,40 2,50 3,50
6000 lbs 0,08 0,08 0,14 0,18 0,21 0,46 0,70 0,89 1,20 - - -
Welding boss 0,20 0,23 0,29 0,38 0,53 0,83 1,31 1,86 - - - -
112 ahlsell
WeIGHt OF FIttINGs
90° ELBOWS, BUTT-WELD FITTINGS (LONG RADIUS)
90° ELBOWS, BUTT-WELD FITTINGS (SHORT RADIUS)
N.B. SIzE APPROXIMATE WEIGHTS IN Kg Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160
1 ⁄ 2 15 0,03 0,05 0,06 0,06 0,09 0,09 0,12 0,12
3 ⁄ 4 20 0,04 0,07 0,08 0,08 0,11 0,11 0,15 0,15
1 25 0,07 0,14 0,15 0,15 0,2 0,2 0,28 0,38
1 1⁄4 32 0,1 0,23 0,26 0,26 0,35 0,35 0,44 0,6
1 1⁄2 40 0,15 0,3 0,4 0,4 0,55 0,55 0,65 0,95
2 50 0,3 0,5 0,7 0,7 0,95 0,95 1,4 1,7
2 1⁄2 65 0,55 0,85 1,4 1,4 1,5 1,5 2,5 3,2
3 80 1 1,25 2,5 2,5 2,9 2,9 3,75 5,5
3 1⁄4 90 1,2 1,65 3 3 4 4 – 8
4 100 1,6 2,1 4 4 6 6 7,5 9 12
5 125 2,7 3,65 6,8 6,8 9,3 9,3 12,7 15 18
6 150 4,4 5,45 11 11 16,8 16,8 23 26 29,5
8 200 8,8 10,2 17,25 19 22 22 27,25 34,8 34,8 38 40,5 52 55 54
10 250 16,8 18,15 25,85 33,15 41,5 41,5 53,9 53,9 53,9 61,16 75 85 97 109
12 300 24 27,25 37,2 49 60 60 61,25 81,7 80 80 107,4 123 140 157 180
14 350 28 39,95 50 59 70 70 70 83 109 94 94 135 188 190 224 247,45
16 400 38 51,6 64 78,3 95 95 95 125 162 125 125 202 260 274 323 367
18 450 48 65,4 82 99,85 139,15 120 120 176,15 231,5 158 158 290,55 390 405 422 545
20 500 58,4 84,9 100 146 194 146 146 228,35 311 194 194 390,45 476 508 607 770
22 550 – – 120 – – – 177,97 – – – 236 – – – – –
24 600 88 146 146 220 318,25 220 220 363,15 532,5 282 282 657,85 820 954 1100 1270
N.B. SIzE APPROXIMATE WEIGHTS IN Kg Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160 1 ⁄ 2 15 0,02 0,04 0,05 0,05 0,07 0,07
3 ⁄ 4 20 0,03 0,05 0,06 0,06 0,08 0,08
1 25 0,05 0,1 0,11 0,11 0,15 0,15
1 1⁄4 32 0,08 0,17 0,18 0,18 0,26 0,26
1 1⁄2 40 0,11 0,23 0,3 0,3 0,39 0,39
2 50 0,23 0,38 0,53 0,53 0,67 0,67
2 1⁄2 65 0,41 0,64 1,05 1,05 1,05 1,05
3 80 0,75 0,94 1,88 1,88 2,03 2,03
3 1⁄2 90 0,9 1,24 2,25 2,25 2,8 2,8
4 100 1,2 1,58 3 3 4,2 4,2 4,5
5 125 2,03 2,74 5,1 5,1 6,5 6,5 9
6 150 3,3 4,09 8,25 8,25 11,75 11,75 13,5
8 200 6,6 7,65 11,1 11,35 16,5 16,5 18,15 24,35 24,35 26,35 29 32
10 250 12,45 13,61 17,35 21,35 31,13 31,13 37,7 37,7 37,7 40,85 50 53 62
12 300 18 20,44 25 33,15 45 45 48 54,5 56 56 68 81,25 92 99
14 350 21 29,96 37,5 39,5 52,5 52,5 52,5 54,45 74 66 66 93,5 124 120 138,8
16 400 28,5 38,7 48 52,2 71,25 71,25 71,25 104,3 106,7 104,3 104,3 138 171,5 166 198
18 450 36 49,05 61,5 65,35 92,15 90 90 118 154,35 110,6 110,6 193 257,4 283 387
20 500 43,8 63,68 75 109,5 135,8 109,5 109,5 154,35 208 135,8 135,8 261 332 376 430
22 550 – – 90 – – – – – – – – – – – –
24 600 66 109,5 109,5 165 214,3 165 165 256,5 355,5 197,5 197,5 443,5 530 621 680
ahlsell 113
WeIGHt OF FIttINGs
45° ELBOWS, BUTT-WELD FITTINGS
END CAPS, BUTT-WELD FITTINGS
N.B. SIzE APPROXIMATE WEIGHTS IN Kg Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160 1 ⁄ 2 15 0,02 0,03 0,03 0,03 0,05 0,05 0,06 0,06
3 ⁄ 4 20 0,02 0,04 0,04 0,04 0,06 0,06 0,08 0,08
1 25 0,04 0,07 0,08 0,08 0,1 0,1 0,14 0,19
1 1⁄4 32 0,05 0,11 0,13 0,13 0,18 0,18 0,22 0,3
1 1⁄2 40 0,08 0,15 0,2 0,2 0,28 0,28 0,33 0,48
2 50 0,15 0,25 0,35 0,35 0,46 0,46 0,7 0,85
2 1⁄2 65 0,28 0,43 0,7 0,7 0,75 0,75 1,25 1,6
3 80 0,5 0,63 1,25 1,25 1,45 1,45 1,88 2,75
3 1⁄2 90 0,6 0,83 1,5 1,5 2 2 – 4
4 100 0,8 1,05 2 2 3 3 3,75 4,5 5,1
5 125 1,35 1,83 3,4 3,4 4,65 4,65 6,35 7,5 9
6 150 2,2 2,73 5,5 5,5 8,4 8,4 11,5 13 14,75
8 200 4,4 5,1 10 10 11 11 13,6 17,4 17,4 19 20,25 26 27,5 27
10 250 8,3 9,08 18,5 15,85 20,75 20,75 26,95 26,95 26,95 30,58 37,5 42,5 48,5 54,4
12 300 12 13,63 24,75 24,5 30 30 30,85 40,85 40 40 53,7 61,5 70 78,5 90
14 350 14 20 25 37 35 35 35 40,85 54,5 47 47 67,5 94 95 112 123,73
16 400 19 25,8 32 46,5 47,5 47,5 47,5 62,5 81 62,5 62,5 101 130 137 161,5 183
18 450 24 32,7 41 56 69,45 60 60 87,15 115,75 79 79 145,25 195 202,5 211 272,5
20 500 29,2 42,45 50 73 97 73 73 113,5 155,5 97 97 195,23 238 254 303,5 385
22 550 – – 60 – – – 88,98 – – – 118 – – – – –
24 600 44 73 73 110 159 110 110 190,65 266,5 141 141 333,93 410 477 545 635
N.B. SIzE APPROXIMATE WEIGHTS IN Kg Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160 1 ⁄ 2 15 0,01 0,01 0,03 0,03 0,05 0,05
3 ⁄ 4 20 0,02 0,02 0,06 0,06 0,09 0,09
1 25 0,04 0,05 0,1 0,1 0,13 0,13 0,15 0,2
1 1⁄4 32 0,05 0,07 0,14 0,14 0,19 0,19 0,23 0,3
1 1⁄2 40 0,08 0,1 0,2 0,2 0,23 0,23 0,3 0,35
2 50 0,1 0,13 0,25 0,25 0,3 0,3 0,55 0,6
2 1⁄2 65 0,14 0,18 0,35 0,35 0,45 0,45 0,9 1
3 80 0,25 0,36 0,7 0,7 0,85 0,85 1,45 1,8
3 1⁄2 90 0,4 0,5 1 1 1,3 1,3 – 2,75
4 100 0,43 0,55 1,1 1,1 1,6 1,6 2,5 2,75 3,5
5 125 0,8 1 2 2 2,7 2,7 4 5 5,5
6 150 1,2 1,5 3 3 4,4 4,4 6 7,5 8,1
8 200 2,2 2,75 4,5 5 5,5 5,5 7 8,35 8,35 11 15,5 18,5 15,45 13,15
10 250 3,6 4,45 6 8 9 9 13,6 13,6 13,6 16,25 21 30 28 28,5
12 300 6 7,5 10 13 15 15 19 25,5 22,5 22,5 29,5 32,5 41 42 44,5
14 350 6,4 8,17 14 13,5 16 16 16 24,5 38 27 27 36,3 50 47 52 59,6
16 400 8,4 10,67 18 18 21 21 21 31,5 52,5 31,5 31,5 52,25 64 59 73 79
18 450 10,4 13 22 22 30 26 26 42 66 36 36 72,5 75 88 93 104
20 500 13,6 17 29 34 42 34 34 56,75 94,5 42 42 98,5 96 105 153 170
22 550 – – 35,5 – – – 42 – – – 51 – – – – –
24 600 20,8 26 44 52 74,5 52 52 96,5 120 60 60 150 118 200 250 285
114 ahlsell
WeIGHt OF FIttINGs
EQUAL TEES, BUTT-WELD FITTINGS
REDUCING TEES, BUTT-WELD FITTINGS
N.B. SIzE APPROXIMATE WEIGHTS IN Kg Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160 1⁄2 15 0,07 0,09 0,16 0,16 0,25 0,25 0,27 0,27
3⁄4 20 0,09 0,11 0,23 0,23 0,38 0,38 0,47 0,47
1 25 0,14 0,27 0,35 0,35 0,5 0,5 0,86 0,65
1 1⁄4 32 0,35 0,45 0,9 0,9 1,05 1,05 1,25 1,18
1 1⁄2 40 0,55 0,65 1,35 1,35 1,5 1,5 1,85 2
2 50 0,68 1,7 1,7 1,7 2,15 2,15 3,18 3
2 1⁄2 65 1,06 2,18 2,7 2,7 3 3 4 4,5
3 80 1,5 3 3,75 3,75 3,8 3,8 6,58 7,1
3 1⁄2 90 2 4,05 5 5 5,25 5,25 10,9
4 100 2,6 4,4 6,5 6,5 7,65 7,65 9 17 15
5 125 4 7,42 10 10 13,5 13,5 17,5 25 24
6 150 6,35 12,35 16 16 19,3 19,3 24 39,5 37,6
8 200 10,7 20 23 24,6 27 27 31,75 33 33 43,6 49,5 54 70,35 68
10 250 18 28,15 34,7 40 45 45 60 60 60 67,5 74 93 98,5 120,3
12 300 26 47,45 59 56,6 65 65 70,5 95 78 78 115 136,2 150 176,5 183,85
14 350 40,7 69,9 87,16 94,5 102 102 102 105 135 115 115 165 206 240 275 300
16 400 43,95 72,65 90,8 100 110 110 110 167 206,5 167 167 249 335 330 385 425
18 450 53,95 101,7 127,12 127 164 135 135 237,45 277 190 190 322 380 450 500 590
20 500 67,2 169,8 199,76 168 245 168 168 320 378,65 245 245 459 540 590 720 790
22 550 – - 220 – – – 220 – – 280 – – – – –
24 600 95,9 306,45 310 240 373 240 240 570,65 653,75 350 350 748 910 1100 1180 1310
N.B. SIzE APPROXIMATE WEIGHTS IN Kg Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160 1 ⁄ 2 15 0,07 0,09 0,16 0,16 0,25 0,25 0,27 0,27
3 ⁄ 4 20 0,09 0,11 0,23 0,23 0,38 0,38 0,47 0,47
1 25 0,14 0,27 0,35 0,35 0,5 0,5 0,86 0,65
1 1⁄4 32 0,35 0,45 0,9 0,9 1,05 1,05 1,25 1,18
1 1⁄2 40 0,55 0,65 1,35 1,35 1,5 1,5 1,85 2
2 50 0,68 1,7 1,7 1,7 2,15 2,15 3,18 3
2 1⁄2 65 1,06 2,18 2,7 2,7 3 3 3,85 4,2
3 80 1,5 3 3,75 3,75 3,8 3,8 6,13 6,6
3 1⁄2 90 2 4,05 5 5 5,25 5,25 10,9
4 100 2,6 4,4 6,5 6,5 7,65 7,65 9 15,9 15
5 125 4 7,42 10 10 13,5 13,5 17,5 23 23,15
6 150 5,6 12,35 14 14 19,3 19,3 24 32,7 37,6
8 200 10,7 20 23 24,6 27 27 31,75 33 33 43,6 49,5 49,25 55,6 51,3
10 250 17,45 26,3 33,15 38,6 43,5 43,5 55 55 55 65,83 63,5 88,5 95 113
12 300 25,25 47,45 59 56,6 63 63 70,5 95 78 78 106,24 124,85 140,85 158 163,45
14 350 40,7 69,9 87,16 94,5 102 102 102 105 135 115 115 162,28 206 235 275 300
16 400 43,95 72,65 90,8 100 110 110 110 167 206,5 167 167 200 335 320 360 410
18 450 53,95 101,7 127,12 127 164 135 135 237,45 256,5 190 190 278,87 380 440 475 550
20 500 67,2 169,8 199,76 168 218 168 168 265,1 350,5 218 218 405,42 540 570 680 770
22 550 – – 220 – – – 220 – – – 280 – – – – –
24 600 94,45 268,99 272 227 373 237 237 390,45 544,8 350 350 606,1 910 1060 1140 1270
ahlsell 115
WeIGHts OF FIttINGs
N.B. SIzE APPROXIMATE WEIGHTS IN Kg
Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160
1 ⁄ 2 15
3 ⁄ 4 20 0,03 0,03 0,07 0,07 0,1 0,1 0,15 0,14
1 25 0,05 0,07 0,13 0,13 0,16 0,16 0,23 0,2
1 1⁄4 32 0,07 0,09 0,18 0,18 0,22 0,22 0,27 0,3
1 1⁄2 40 0,12 0,14 0,26 0,26 0,35 0,35 0,48 0,45
2 50 0,15 0,23 0,41 0,41 0,57 0,57 0,95 0,9
2 1⁄2 65 0,32 0,41 0,77 0,77 1,01 1,01 1,35 1,35
3 80 0,4 0,5 1 1 1,35 1,35 1,9 1,8
3 1⁄2 90 0,55 0,68 1,3 1,3 1,89 1,89 – 3,2
4 100 0,65 0,82 1,6 1,6 2,27 2,27 3,65 3,65 3,85
5 125 1,1 1,35 2,75 2,75 3,92 3,92 6,35 6,35 6,35
6 150 1,6 2 3,95 3,95 5,94 5,94 7,5 10 9
8 200 2,6 3,27 5 5,58 6,5 6,5 8 9,86 9,86 11,8 13,5 16,35 16,5 14,5
10 250 4,3 5,45 7,25 8,99 10,7 10,7 14,48 14,48 14,48 17,25 20,45 24,5 28,5 29,5
12 300 6 7,7 9,7 13,21 15 15 16,35 22,25 19,79 19,79 28,15 32,65 38,15 44,25 49
14 350 10,75 13,6 23 22,25 26,85 26,85 26,85 31,3 41,75 35,55 35,55 52,25 64 73 78 86
16 400 13,25 16,35 28 27,5 33,15 33,15 33,15 44 56,75 44 44 73,5 83 97 112 121
18 450 16 19,98 34 33,5 46,76 40 40 59,5 77,4 53,12 53,12 97,6 116 136 145 159
20 500 23,8 29,75 50 59,45 79 59,45 59,45 93 124,85 79 79 159 163 178 305 340
22 550 – – 57 – – – 65,35 – – – 86,71 – – – – –
24 600 28,7 36,32 63 71,7 107,14 71,7 71,7 129,4 180,7 95,34 95,34 228 241 295 540 610
CONCENTRIC REDUCERS, BUTT-WELD FITTINGS
N.B. Weights are of the smallest reduction, i.e. the heaviest.
ECCENTRIC REDUCERS, BUTT-WELD FITTINGS
N.B. Weights are of the smallest reduction, i.e. the heaviest.
N.B. SIzE APPROXIMATE WEIGHTS IN Kg Sch Sch Sch Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch Sch XXS Inches Metric 5s 10s 10 20 30 40s Wall 40 60 80s XS 80 100 120 140 160
1⁄ 2 15
3⁄ 4 20 0,03 0,03 0,07 0,07 0,1 0,1 0,15 0,14
1 25 0,05 0,07 0,13 0,13 0,16 0,16 0,23 0,2
1 1⁄4 32 0,07 0,09 0,18 0,18 0,22 0,22 0,27 0,3
1 1⁄2 40 0,12 0,14 0,26 0,26 0,35 0,35 0,48 0,45
2 50 0,15 0,23 0,41 0,41 0,57 0,57 0,95 0,9
2 1⁄2 65 0,32 0,41 0,77 0,77 1,01 1,01 1,35 1,35
3 80 0,4 0,5 1 1 1,35 1,35 1,9 1,8
3 1⁄2 90 0,55 0,68 1,3 1,3 1,89 1,89 – 3,2
4 100 0,65 0,82 1,6 1,6 2,27 2,27 3,65 3,65 3,85
5 125 1,1 1,35 2,75 2,75 3,92 3,92 6,35 6,35 6,35
6 150 1,6 2 3,95 3,95 5,94 5,94 7,5 10 9
8 200 2,6 3,27 5 5,58 6,5 6,5 8 9,86 9,86 11,8 13,5 16,35 16,5 14,5
10 250 4,3 5,45 7,25 8,99 10,7 10,7 14,48 14,48 14,48 17,75 20,45 24,5 28,5 29,5
12 300 6 7,7 9,7 13,21 15 15 16,35 22,25 19,79 19,79 28,15 32,65 38,15 44,25 49
14 350 10,75 13,6 23 22,25 26,85 26,85 26,85 31,3 41,75 35,55 35,55 52,25 64 73 78 86
16 400 13,25 16,35 28 27,5 33,15 33,15 33,15 44 56,75 44 44 73,5 83 97 112 121
18 450 16 19,98 34 33,5 46,76 40 40 59,5 77,4 53,12 53,12 97,6 116 136 145 159
20 500 23,8 29,75 50 59,45 79 59,45 59,45 93 124,85 79 79 159 163 178 305 340
22 550 – – 57 – – – 65,35 – – – 86,71 – – – – –
24 600 28,7 36,32 63 71,7 107,14 71,7 71,7 129,4 180,7 95,34 95,34 228 241 295 540 610
116 ahlsell
WeIGHts OF FIttINGs
STUB ENDS, BUTT-WELD FITTINGS (ANSI B16.9)
STUB ENDS, BUTT-WELD FITTINGS (MSS SP-43)
N.B. SIzE APPROXIMATE WEIGHTS IN Kg
Sch Sch Sch Std. Sch Sch Sch Sch Sch Sch Sch XXS
Inches Metric 10 20 30 Wall 40 60 XS 80 100 120 140 160
1⁄2 15 0,13 0,14 0,3
3⁄4 20 0,18 0,2 0,35
1 25 0,29 0,38 0,5 0,66
1 1⁄4 32 0,41 0,54 0,67 0,95
1 1⁄2 40 0,54 0,67 0,9 1,2
2 50 0,98 1,34 2,01 2,46
2 1⁄2 65 1,54 2,05 2,69 3,71
3 80 2,1 2,8 3,93 5,18
3 1⁄2 90 2,47 2,94 6,25
4 100 2,99 4,17 5,27 6,29 7,68
5 125 5,22 7,41 9,6 11,79 13,84
6 150 6,79 10,27 13,04 16,25 19,2
8 200 7,99 8,84 10,28 12,81 15,63 18,21 21,83 24,55 26,79 26,16
10 250 12,1 14,87 17,86 23,8 23,94 28,13 33,57 38,98 45,54 50,45
12 300 14,64 19,29 21,88 23,21 32,23 29,38 38,84 47,32 55,8 62,05 71,43
14 350 18 15,8 28,57 28,57 32,59 44,2 39,73 54,92
16 400 19,75 16,65 32,14 32,14 43,3 56,7 42,86 71,88
18 450 24,25 21,3 44,2 38 56,25 74,2 50 91,52
20 500 36 31,7 55,8 41,96 65,63 88,4 55,81 112,1
22 550 42,95 37 65 46,88 78 109 62,07 142
24 600 50,05 45,55 75,9 50,45 91,52 128,6 67,41 160
N.B. SIzE APPROXIMATE WEIGHTS IN Kg
Inches Metric Sch 5s Sch 10s Sch 40s Sch 80s
1 ⁄ 2 15 0,03 0,04 0,09 0,12
3 ⁄ 4 20 0,04 0,06 0,12 0,16
1 25 0,06 0,08 0,15 0,22
1 1⁄4 32 0,08 0,1 0,2 0,31
1 1⁄2 40 0,11 0,14 0,28 0,39
2 50 0,17 0,2 0,41 0,69
2 1⁄2 65 0,25 0,33 0,66 1,05
3 80 0,35 0,44 0,89 1,46
3 1⁄2 90 0,5 0,63 1,26 1,54
4 100 0,61 0,76 1,52 2,49
5 125 1,06 1,33 2,66 3,55
6 150 1,2 1,51 3,02 5,49
8 200 2,09 2,61 5,22 9,97
10 250 3,63 4,54 9,08 13,75
12 300 5,33 6,67 13,25 19,64
14 350 5,81 7,26 14,53 29
16 400 6,54 8,17 16,34 37,5
18 450 7,72 9,65 19,3 49,25
20 500 8,54 10,67 21,34 60
22 550 9,8 11,6 23 77,5
24 600 10,26 12,83 25,65 88,25
ahlsell 117
WeIGHts OF FLANGes
150 lb PIPE FLANGES
300 lb PIPE FLANGES
400 lb PIPE FLANGES
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
5 125 9,2 9,0 6,3 6,3 7,0 6 150 11,0 11,8 7,5 7,5 8,4 8 200 18,3 21,0 12,6 12,6 13,0 10 250 25,0 30,0 18,5 18,5 17,8 12 300 39,0 45,0 28,0 28,0 29,5 14 350 51,0 59,0 36,0 42,0 39,0 16 400 60,0 79,0 46,0 52,0 42,0 18 450 71,0 97,0 50,0 58,0 54,0 20 500 88,0 124,0 64,0 74,0 68,0 24 600 119,0 188,0 89,0 101,0 93,0
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
5 125 16,0 15,5 12,5 12,5 12,9 6 150 20,2 21,3 14,1 14,1 18,0 8 200 31,0 35,2 24,8 24,8 26,0 10 250 44,3 57,0 37,1 42,0 37,5 12 300 64,0 82,0 50,0 64,0 52,0 14 350 88,0 106,0 70,0 87,0 72,0 16 400 113,0 140,0 90,0 114,0 100,0 18 450 134,0 178,0 112,0 134,0 126,0 20 500 171,0 223,0 133,0 168,0 148,0 24 600 238,0 345,0 208,0 250,0 222,0
APPROXIMATE WEIGHTS IN Kg
N.B. Threaded Weld Lap and Socket
Inches Metric Neck Blind Slip-on Joint Weld
1⁄2 15 0,5 0,4 0,4 0,4 0,4 3⁄4 20 0,7 0,7 0,7 0,7 0,7 1 25 1,1 0,9 0,8 0,8 0,9 1 1⁄4 32 1,5 1,3 1,1 1,1 1,2 1 1⁄2 40 1,8 1,6 1,4 1,4 1,5 2 50 2,7 2,6 2,2 2,2 2,3 2 1⁄2 65 4,4 4,1 3,6 3,6 3,7 3 80 5,2 5,0 4,1 4,1 4,2 3 1⁄2 90 6,4 6,4 5,2 5,2 5,3 4 100 7,5 7,1 5,6 5,6 5,9
APPROXIMATE WEIGHTS IN Kg
N.B. Threaded Weld Lap and Socket
Inches Metric Neck Blind Slip-on Joint Weld
1⁄2 15 0,9 0,7 0,7 0,7 0,7 3⁄4 20 1,5 1,2 1,1 1,1 1,2 1 25 1,9 1,5 1,4 1,4 1,4 1 1⁄4 32 2,6 2,0 1,8 1,8 1,9 1 1⁄2 40 3,3 2,9 2,6 2,6 2,8 2 50 3,6 3,4 3,4 3,4 3,3 2 1⁄2 65 5,4 5,1 4,4 4,4 4,6 3 80 7,4 7,0 6,1 6,1 6,3 3 1⁄2 90 8,9 8,9 7,5 7,5 7,8 4 100 11,9 11,8 10,1 10,1 10,2
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
4 100 14,0 14,0 11,5 11,5 12,5 5 125 19,0 19,0 14,5 14,5 15,5 6 150 25,5 26,0 19,0 19,0 21,0 8 200 39,5 43,0 29,0 32,0 31,0 10 250 54,0 65,0 39,5 44,0 42,0 12 300 78,0 95,0 58,0 65,0 61,0
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
14 350 105,0 126,0 82,0 91,0 85,0 16 400 131,0 163,0 105,0 115,0 110,0 18 450 159,0 206,0 126,0 139,0 131,0 20 500 190,0 270,0 152,0 170,0 157,0 24 600 275,0 410,0 232,0 260,0 225,0
118 ahlsell
WeIGHts OF FLANGes
600 lb PIPE FLANGES
1500 lb PIPE FLANGES
900 lb PIPE FLANGES
APPROXIMATE WEIGHTS IN Kg
N.B. Threaded Weld Lap and Socket
Inches Metric Neck Blind Slip-on Joint Weld
1⁄2 15 0,9 0,7 0,8 0,8 1,0 3⁄4 20 1,5 1,2 1,4 1,4 1,6 1 25 1,9 1,5 1,6 1,6 1,8 1 1⁄4 32 2,6 2,0 2,1 2,1 2,6 1 1⁄2 40 3,3 3,2 3,1 3,1 3,3 2 50 4,7 4,3 3,7 3,7 3,9 2 1⁄2 65 6,5 6,0 5,4 5,4 6,0 3 80 8,7 8,0 7,3 7,3 7,4 3 1⁄2 90 11,2 10,5 8,9 8,9 9,5 4 100 18,1 18,0 15,8 15,8 17,0
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
5 125 30,5 28,5 24,5 24,5 26,5 6 150 36,2 35,5 29,5 29,5 32,0 8 200 56,0 58,0 43,0 43,0 46,0 10 250 91,0 98,0 70,1 77,0 74,0 12 300 105,0 125,0 86,0 92,0 90,0 14 350 127,0 151,0 100,0 114,0 108,0 16 400 178,0 215,0 142,0 160,0 150,0 18 450 216,0 287,0 175,0 192,0 188,0 20 500 268,0 366,0 232,0 260,0 230,0 24 600 380,0 532,0 330,0 368,0 325,0
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
6 150 70,0 72,0 - 61,0 - 8 200 125,0 122,0 - 104,0 - 10 250 204,0 210,0 - 220,0 - 12 300 303,0 315,0 - 287,0 - 14 350 427,0 423,0 - 405,0 - 16 400 570,0 590,0 - 525,0 - 18 450 740,0 795,0 - 670,0 - 20 500 935,0 930,0 - 810,0 - 24 600 1510,0 1510,0 - 1282,0 -
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
3 80 15,0 13,1 11,6 11,6 11,9 4 100 24,0 22,1 19,8 19,8 20,0 5 125 37,0 36,5 32,0 32,0 32,5 6 150 50,0 47,4 41,2 41,2 41,7 8 200 85,0 82,5 78,0 75,0 77,5 10 250 127,0 123,0 110,0 115,0 110,0
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
12 300 170,0 174,0 149,0 155,0 149,0 14 350 198,0 225,0 181,0 170,0 181,0 16 400 224,0 280,0 194,0 210,0 194,0 18 450 300,0 400,0 274,0 298,0 274,0 20 500 374,0 503,0 332,0 370,0 332,0 24 600 680,0 953,0 637,0 710,0 637,0
APPROXIMATE WEIGHTS IN Kg
N.B. Threaded Weld Lap and Socket
Inches Metric Neck Blind Slip-on Joint Weld
1⁄2 15 1,9 1,8 1,7 1,7 1,7 3⁄4 20 2,6 2,4 2,3 2,3 2,4 1 25 3,8 3,6 3,4 3,4 3,5 1 1⁄4 32 4,4 4,1 3,9 3,9 4,0 1 1⁄2 40 6,1 5,8 5,4 5,4 5,5 2 50 11,1 10,1 9,8 9,8 10,0 2 1⁄2 65 15,5 14,0 13,7 13,7 13,9 3 80 20,4 19,0 - 18,0 - 4 100 30,5 30,0 - 27,8 - 5 125 58,0 58,0 - 52,0 -
ahlsell 119
WeIGHts OF FLANGes/BARs/PLAtes
2500 lb PIPE FLANGES
ROUND BAR - metric
PLATE- metric
Pipes ANSI B.36.10 see page 4-13 - Pipes ANSI B.36.19 see page 3 - Flanges MSS SP44 see page 67-71
SIzE WEIGHTS IN Kg
mm Wt per ft Wt per M
0,5 0,0004 0,0015 1,0 0,0018 0,0062 1,5 0,0042 0,014 2 0,0076 0,025 2,5 0,012 0,039 3 0,017 0,055 3,5 0,023 0,076 4 0,03 0,099 4,5 0,038 0,125 5 0,047 0,154 5,5 0,057 0,187 6 0,068 0,222 6,5 0,079 0,26 7 0,092 0,302 7,5 0,106 0,347 8 0,12 0,395 8,5 0,136 0,445 9 0,152 0,499 9,5 0,169 0,556 10 0,188 0,617 11 0,227 0,746 12 0,271 0,888 13 0,317 1,04 14 0,369 1,21 15 0,424 1,39 16 0,482 1,58 17 0,543 1,78 18 0,61 2 19 0,68 2,23 20 0,753 2,47
SIzE WEIGHTS IN Kg
mm Wt per ft Wt per M
21 0,829 2,72 22 0,908 2,98 23 0,994 3,26 24 1,08 3,55 25 1,17 3,85 26 1,27 4,17 27 1,37 4,5 28 1,47 4,83 30 1,69 5,55 32 1,92 6,31 33 2,-05 6,71 35 2,3 7,55 36 2,44 7,99 38 2,71 8,9 39 2,86 9,38 40 3,01 9,86 42 3,32 10,88 45 3,8 12,48 48 4,33 14,21 50 4,7 15,41 52 5,08 16,67 55 5,69 18,65 56 5,89 19,33 58 6,32 20,74 60 6,77 22,2 62 7,22 23,7 64 7,7 25,25 65 7,94 26,05 68 8,69 28,51 70 9,21 30,21
SIzE WEIGHTS IN Kg
mm Wt per ft Wt per M
72 9,74 31,96 75 10,57 34,68 80 12,03 39,46 90 15,22 49,94 100 18,79 61,65 110 22,74 74,6 120 27,07 88,8 130 31,7 104 140 36,88 121 150 42,37 139 160 48,16 158 170 54,26 178 180 60,96 200 190 67,97 223 200 75,3 247 220 90,8 298 240 108 355 250 117 385 260 127 417 280 147 483 300 169 555 320 192 631 340 217 713 350 230 755 360 244 799 380 271 890 400 301 986 500 469 1540
WEIGHTS IN Kg
THICKNESS Wt per sq ft Wt per sq m 2000 2500 3000 4000 6000 x 1000 mm x 1250 mm x 1500 mm x 2000 mm x 2000mm
5 mm 3,802 40,925 82 128 184 327 491 6 mm 4,563 49,111 98 153 221 393 589 8 mm 6,084 65,483 131 205 295 524 786 10 mm 7,604 81,845 164 256 368 655 982 12 mm 9,125 98,222 196 307 442 786 1179 15 mm 11,406 122,778 246 384 553 982 1473 20 mm 15,207 163,689 327 512 737 1310 1964 25 mm 19,01 204,622 409 639 921 1637 2456 30 mm 22,813 245,556 491 767 1105 1964 2947 40 mm 30,414 327,378 655 1023 1473 2619 3929 50 mm 38,02 409,244 819 1279 1842 3274 4911
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
1/2 15 3,6 3,0 - 3,0 3,0 3/4 20 4,0 4,5 - 4,0 4,0 1 25 6,0 5,0 - 5,0 5,0 1 1⁄4 32 9,0 8,0 - 8,0 8,0 1 1⁄2 40 13,0 11,0 - 11,0 11,0 2 50 19,0 17,0 - 17,0 17,0 2 1⁄2 65 24,0 25,0 - 25,0 25,0
APPROXIMATE WEIGHTS IN Kg N.B. Weld Lap Inches Metric Neck Blind Slip-on Joint Threaded
3 80 43,0 39,0 - 38,0 - 4 100 66,0 60,0 - 58,0 - 5 125 111,0 101,0 - 95,0 - 6 150 172,0 156,0 - 146,0 - 8 200 261,0 242,0 - 220,0 - 10 250 485,0 465,0 - 420,0 - 12 300 730,0 665,0 - 500,0 -
120 ahlsell
The editorial group closed its work September 2007. Specifications are subject to change without prior notice.Ahlsell Oil & Gas AS, PO Box 8055, 4068 Stavanger
IN NO EVENT WILL AHLSELL OIL & GAS AS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INDIRECT, INCIDENTAL, PUNITIVE OR SPECIAL DAMAGES, INCLUDING ANY LOST PROFITS OR LOST SAVINGS, EVEN IF A REPRESENTATIVE OF AHLSELL OIL & GAS AS OR ANY SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD PARTY. SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
Melvæ
r&L
ien Th
e Idea En
trepreneu
r. Ph
oto: Tom H
aga
How to contact us
Stavanger Office
Phone: +47 51 57 39 00Fax: +47 51 81 86 50E-mail: oil&[email protected]
Internet:www.ahlselloilgas.com
Visit address:Gamle Forusvei 534033 Stavanger
Postal address:PO box 80554068 Stavanger
Bergen Office
Phone: +47 51 57 39 00Fax: +47 55 94 48 40E-mail: oil&[email protected]
Internet:www.ahlselloilgas.com
Visit address:Godviksvingene 1745179 Bergen
Postal address:PO box 51 Godvik5882 Bergen
Abu Dhabi Branch Office
Phone: +971 2 634 9999Fax: +971 2 632 17 11E-mail: [email protected]
Internet:www.ahlselloilgas.com
Postal address:c/o EMDAD LCCPO box 4118Abu Dhabi, U.A.E