7/27/2019 Plastic Injection Moulding Machines

1/2

TECHNICAL SPECIFICATIONS [NT-SERIES] NebulaHydraulic ServicesMODEL UNIT NT 50-T NT 80-T NT 100-T NT 150-T NT 200-T

INJECTION UNIT :

Actual Shot Weight [pp] gram 100 165 150 235 215 325 295 425 400 550

Theoretical Shot Volume cc 135 220 200 315 285 430 395 565 535 729

Injection Pressure kg/cm2 1815 1091 1710 1005 1329 1003 1503 1052 1417 1035

Injection Rate cc/s 50 81 63 98 89 134 109 156 124 199

Chamber Diameter mm 35 45 40 50 45 55 50 60 55 65Screw Diameter mm 35 40 45 50 55

Screw Stroke mm 140 160 180 200 225

Screw Speed rpm 280 262 295 280 253

Screw L/D Ratio % 01:22 01:22 01:22 01:22 01:22

Plasticizing Capacity kg/hr. 48 70 96 124 148

Temperature Zone nos. 6+1 6+1 6+1 6+1 6+1

CLAMPING UNIT :

Clamping Force ton 50 80 100 150 200

Mould Opp. Stroke mm 310 330 395 435 470

Dist. Between Tie bar mm 340 X 340 370 X 370 430 X 430 485 X 485 510 X 510

Maxi. Mould Height mm 340 400 450 500 550

Mini. Mould Height mm 120 150 180 200 210

Locating Ring Diameter mm 100 100 125 125 150

Ejector Stroke mm 90 110 150 170 130

Ejector Force ton 3.1 3.8 4.5 5.1 7

ELECTRICAL DATA :

Electric pump motor kw[hp] 05.5[07.5] 07.5[10.0] 09.3[12.5] 11.0[15.0] 15.0[20.0]

Electric Heater kw[hp] 03.5[04.5] 05.0[06.5] 06.5[08.5] 08.5[11.5] 10.5[14.0]

Total Electric Load kw[hp] 08.0[12.0] 11.5[16.5] 15.5[20.5] 19.5[26.5] 25.5[34.0]

GENERAL DATA :

Machine Weight [App.] Ton 3 4 5 7 9

MODELUNIT

NT 250-T

NT 300-T

NT 400-T NT 500-T NT 600-T

INJECTION UNIT :

Actual Shot Weight [pp] gram 530 720 700 1050 925 1350 1225 1760 1580 2230

Theoretical Shot Volume cc 705 960 945 1425 1230 1814 1633 2352 2100 2975

Injection Pressure kg/cm2 1465 1010 1561 1030 1701 1154 1694 1183 1956 1397

Injection Rate cc/s 141 192 159 242 185 274 214 308 251 349

Chamber Diameter mm 60 75 65 80 70 85 75 90 80 95

Screw Diameter mm 60 65 70 75 80

Screw Stroke mm 250 285 320 370 420

Screw Speed rpm 257 266 287 288 295

Screw L/D Ratio % 01:22 01:22 01:22 01:22 01:22

Plasticizing Capacity kg/hr. 165 173 186 216 237

Temperature Zone nos. 6+1 6+1 6+1 6+1 6+1CLAMPING UNIT :

Clamping Force ton 250 300 400 500 600

Mould Opp. Stroke mm 550 660 730 790 850

Dist. Between Tie bar mm 570 X 570 660 X 660 760 X 760 820 X 820 900 X 900

Maxi. Mould Height mm 580 660 750 800 950

Mini. Mould Height mm 230 300 320 350 450

Locating Ring Diameter mm 160 160 160 200 200

Ejector Stroke mm 180 190 200 220 250

Ejector Force ton 7 8 10.2 13.3 16.6

ELECTRICAL DATA :

Electric pump motor kw[hp] 18.5[25.0] 22.5[30.0] 30.0[40.0] 37.5[50.0] 45.0[60.0]

Electric Heater kw[hp] 13.5[18.0] 16.5[22.0] 19.5[26.0] 24.0[32.0] 30.0[40.0]

Total Electric Load kw[hp] 32.0[43.0] 38.0[52.0] 49.5[66.0] 61.5[82.0] 75.0[100.0]

GENERAL DATA :

Machine Weight [App.] Ton 11 13 16 19 22

NOTE : SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.

7/27/2019 Plastic Injection Moulding Machines

2/2