polyimide thermofoil™ heaters · 2017-06-28 · polyimide thermofoil™ heaters thin, flexible...
TRANSCRIPT
16
IntroductionD
esignG
uidePolyim
ideH
eatersSiliconeRub
ber
Heaters (foil)
StandardPolyim
ide&
Rubb
er
Rubb
erH
eaters(w
ire-wound)
Mica H
eatersTherm
al-Clear
Heaters
All-Polyim
ideH
eatersSensors,
Controllers &
Accessories
Reference
S a l e s a n d S u p p o r tAmericas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacific: (65) 6511 3388|
Specifications subject to change
Polyimide Thermofoil™ Heaters
Thin, flexible heating solutions from -200 to 200°C
Overview
Polyimide (Kapton™) is a thin, semitransparent material withexcellent dielectric strength. Polyimide Thermofoil™ heaters areideal for applications with space and weight limitations, orwhere the heater will be exposed to vacuum, oil, or chemicals.
• Thin, lightweight heaters allow you to apply heat where it’sneeded, reducing operating costs
• Etched-foil heating technology provides fast and efficientthermal transfer
• Customized options (i.e. SMT components, flex leads and con-nectors) offer turnkey solutions to drastically reduce assemblytime and increase productivity
• Custom profiling gives uniform thermal performance of theheating output to improve processing yields and productivity
• FEP internal adhesive for use to 200°C (392°F)
• UL component recognition available
• Suitable for vacuum environments (NASA-RP-1061)
• NASA approved materials for space applications (S-311-P-079)
• Resistant to most chemicals: acids and solvents
• Radiation resistant to 106 rads if built with polyimide-insulated leadwire (custom option)
• Very small sizes available
• Fluid immersible designs available (not standard)
Configure Minco heaters and order online at:
www.minco.com/heater_config/
Typical applications
• Medical diagnostic instruments and analyzers
• Maintain warmth of satellite components
• Protect aircraft electronic and mechanical devices againstcold at high altitudes
• Stabilize optoelectronic components
• Test or simulate integrated circuits
• Enable cold weather operation of outdoor electronics such ascard readers, LCDs or ruggedized laptops
• Maintain constant temperature in analytic test equipment
Custom options
• Custom shapes and sizes:Polyimide / FEP – 22" x 42" (560 x 1065 mm)Polyimide / WA/ULA – 22” x 72” (560 x 1825 mm)
• Custom resistance: Polyimide / FEP – 450 Ω/in² (70 Ω/cm²)Polyimide / WA/ULA – 1500 Ω/in² (233 Ω/cm²)
• WA or ULA internal adhesive is more economical than FEP formost custom designs that operate below 150°C
• Available with surface mount sensors, connectors, heat sinksand even integral controllers
• NASA approval is available in nearly all of the standard sizePolyimide heaters
• TÜV or UL recognition marking is optional
• Tighter resistance tolerance
• RoHS compliance
• Contact Access: Minco Sales and Support for design assistance
17
Intr
oduc
tion
Des
ign
Gui
dePo
lyim
ide
Hea
ters
Silic
one
Rub
ber
Hea
ters
(foi
l)
Stan
dard
Poly
imid
e&
Rub
ber
Rub
ber
Hea
ters
(wire
-wou
nd)
Mic
a H
eate
rsTh
erm
al-C
lear
Hea
ters
All-
Poly
imid
eH
eate
rsSe
nsor
s,C
ontr
olle
rs &
Acc
esso
ries
Refe
renc
e
| Flexible Heaters Design Guide | www.minco.com
Specifications subject to change
Polyimide Thermofoil™ Heaters
Specifications
Temperature range: -200 to 200°C (-328 to 392°F). Upper limitwith 0.003” (0.08 mm) foil backing is 150°C (302°F).
Material: .0.002” Polyimide/0.001” FEP, (0.05/0.03 mm).
Resistance tolerance: ±10% or ±0.5 Ω, whichever is greater.
Dielectric strength: 1000 VRMS.
Minimum bend radius: 0.030” (0.8 mm).
Leadwire: Red PTFE insulated, stranded.
Current capacity (based on 100°C max. ambient temp.):
AWG 30 - 3.0 AAWG 26 - 5.0 AAWG 24 - 7.5 AAWG 20 - 13.5 A
Maximum heater thickness:
Over element 0.012” (0.3 mm)Over leads
AWG 30 (0.057 mm²) 0.050” (1.3 mm)AWG 26 (0.141 mm²) 0.060” (1.5 mm)AWG 24 (0.227 mm²) 0.065” (1.7 mm)AWG 20 (0.563 mm²) 0.085” (2.2 mm)
Add 0.005” (0.1 mm) to above dimensions for foil backing.
Dimensional tolerance:
6” (150 mm) or less ±0.03” (±0.8 mm)6.01 to 12” (150 to 300 mm) ±0.06” (±1.5 mm)Over 12” (300 mm) ±0.12” (±3.0 mm)
Tighter tolerances are available on custom designs if needed.
Polyimide/FEP HeatersMaximum Watt Density
Example: At 50°C, the maximum power for a heater mounted with acrylicPSA is 20 W/in² (3.1 W/cm²).
-148°F -103°F -58°F -13°F 32°F 77°F 122°F 167°F 212°F 257°F 302°F 347°F 392°F 437°F60
50
40
30
20
10
0
9.3
7.75
6.2
4.65
3.1
1.55
0-100°C -75°C -50°C -25°C 0°C 25°C 50°C 75°C 100°C 125°C 150°C 175°C 200°C 225°C
BM3 Shrink Band
Stretch tape or Clamped12 PSA w/ Aluminum
Acrylic PSA w/ Aluminum
Acrylic PSA
#15 Epoxy
MOUNTING METHOD
HEATER:0.002” POLYIMIDE (0.05mm)0.001” ADHESIVE (0.03 mm)
Max
imum
allo
wab
le p
ower
:
Wat
ts/s
quar
e in
ch o
f effe
ctiv
e ar
ea
Wat
ts/s
quar
e cm
Flexible Heaters Prototype Design Kit
The Flexible Heaters Prototype Design Kit allows you to easily test and prototype a heating concept before startingon a journey of custom-built-to-order product.
Filled with polyimide and silicone rubber Thermofoil™heaters, instructions and technical data, this kit will helpyou move towards successfully integrating flexible heatersinto your application.
Model Number TB-H1
18
IntroductionD
esignG
uidePolyim
ideH
eatersSiliconeRub
ber
Heaters (foil)
StandardPolyim
ide&
Rubb
er
Rubb
erH
eaters(w
ire-wound)
Mica H
eatersTherm
al-Clear
Heaters
All-Polyim
ideH
eatersSensors,
Controllers &
Accessories
Reference
S a l e s a n d S u p p o r tAmericas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacific: (65) 6511 3388|
Specifications subject to change
Stock Polyimide Thermofoil™ Heaters
These heaters are normally available from stock for immediateshipment. Voltage and wattage values are for reference only.Heaters may be operated at other voltages if they do notexceed the maximum allowable watt density ratings.
See "Standard Polyimide & Rubber Heaters" (pages 22-31) forthese and other models with additional ordering options:
• Greater selection of resistances
• Variable lead length
• More backing options
• UL recognition marking U
Specification options
Type (configuration)
1 31 XY
TAB DIMENSIONS:AWG 30: 0.40" long × 0.25" wide (10.2 × 6.4 mm)AWG 24/26: 0.40" × 0.40" (10.2 × 10.2 mm)
X
Y
*Resistance tolerance is ±10% or ±0.5 Ω, whichever is greaterNote: Standard leadwire length is 12" (305mm) minimum
Size (inches) Size (mm) Type Resistancein ohms*
Typical power Effective areain² (cm²)
LeadAWG
ModelnumberX Y X Y
0.50 2.00 12.7 50.8 1 1 157 5 W at 28 V 0.79 (5.10) 30 HK5160R157L12
0.50 4.00 12.7 101.6 1 1 78.4 10 W at 28 V 1.67 (10.77) 30 HK5161R78.4L12
0.50 6.00 12.7 152.4 1 1 52.3 15 W at 28 V 2.35 (15.16) 30 HK5162R52.3L12
1.00 1.00 25.4 25.4 1 1 157 5 W at 28 V 0.82 (5.29) 30 HK5163R157L12
1.00 2.00 25.4 50.8 1 1 78.4 10 W at 28 V 1.76 (11.35) 30 HK5164R78.4L12
1.00 3.00 25.4 76.2 1 1 52.3 15 W at 28 V 2.70 (17.42) 30 HK5165R52.3L12
1.00 5.00 25.4 127.0 1 1 529 25 W at 115 V 4.41 (28.45) 30 HK5166R529L12
1.00 10.00 25.4 254.0 1 1 264 50 W at 115 V 8.96 (57.81) 30 HK5167R264L12
1.00 15.00 25.4 381.0 1 1 176 75 W at 115 V 13.51 (87.16) 30 HK5168R176L12
2.00 2.00 50.8 50.8 1 1 661 20 W at 115 V 3.59 (23.16) 30 HK5169R661L12
2.00 3.00 50.8 76.2 1 1 441 30 W at 115 V 5.50 (35.48) 30 HK5170R441L12
2.00 4.00 50.8 101.61 1 1 331 40 W at 115 V 7.41 (47.81) 30 HK5171R331L12
2.00 6.00 50.8 152.4 1 1 220 60 W at 115 V 11.23 (72.45) 30 HK5172R220L12
2.00 12.00 50.8 304.8 1 1 110 120 W at 115 V 22.69 (146.39) 24 HK5173R110L12
3.00 3.00 76.2 76.2 1 1 294 45 W at 115 V 8.41 (54.26) 30 HK5174R294L12
3.00 5.00 76.2 127.0 1 1 176 75 W at 115 V 14.23 (91.81) 30 HK5175R176L12
3.00 10.00 76.2 152.4 1 1 88.2 150 W at 115 V 28.75 (185.48) 24 HK5176R88.2L12
3.00 15.00 76.2 381.0 1 1 58.8 225 W at 115 V 43.30 (279.35) 24 HK5177R58.8L12
4.00 4.00 101.6 101.6 1 1 165 80 W at 115 V 15.20 (98.06) 30 HK5178R165L12
4.00 8.00 101.6 203.2 1 1 82.7 160 W at 115 V 30.84 (198.97) 24 HK5179R82.7L12
4.00 12.00 101.6 304.8 1 1 55.1 240 W at 115 V 46.48 (299.87) 24 HK5180R55.1L12
5.00 5.00 127.0 127.0 1 1 106 125 W at 115 V 24.02 (154.97) 24 HK5181R106L12
5.00 10.00 127.0 254.0 1 1 52.9 250 W at 115 V 48.57 (313.35) 24 HK5182R52.9L12
5.00 15.00 127.0 381.0 1 1 35.3 375 W at 115 V 73.12 (471.74) 24 HK5183R35.3L12
10.00 10.00 254.0 254.0 1 1 26.4 500 W at 115 V 97.52 (629.16) 20 HK5184R26.4L12
10.00 15.00 254.0 381.0 1 1 17.6 750 W at 115 V 146.92 (947.87) 20 HK5185R17.6L12
0.50 0.09 12.7 2.4 31K 25.0 1 W at 5 V 0.13 (0.84) 30 HK5186R25.0L12
1.00 0.09 25.4 2.4 31K 157 5 W at 28 V 0.68 (4.39) 26 HK5187R157L12
3.00 0.12 76.2 3.1 31K 378 35 W at 115 V 6.61 (42.65) 26 HK5188R378L12
HK5160R157L12 Model number
A Heater backingA = No adhesive -200 to 200°CB = PSA backing -32 to 100°C
HK5160R157L12A = Sample part number
19
Intr
oduc
tion
Des
ign
Gui
dePo
lyim
ide
Hea
ters
Silic
one
Rub
ber
Hea
ters
(foi
l)
Stan
dard
Poly
imid
e&
Rub
ber
Rub
ber
Hea
ters
(wire
-wou
nd)
Mic
a H
eate
rsTh
erm
al-C
lear
Hea
ters
All-
Poly
imid
eH
eate
rsSe
nsor
s,C
ontr
olle
rs &
Acc
esso
ries
Refe
renc
e
| Flexible Heaters Design Guide | www.minco.com
Specifications subject to change
Overview
Minco’s commercial grade polyimide heaters provide theperformance and reliability you expect at a lower cost thanour standard polyimide/FEP models. Sizes are available for12 and 24 volt operation, or connect multiple heaters in aseries/parallel system for consistent power over larger areas.
• Solder pad option provides you the lowest price possiblefor Minco polyimide heaters
• All models include acrylic pressure sensitive mountingadhesive (PSA) for simple installation
• Ideal for prototyping, short production series or high volume/low cost applications
• Typical lead time is 3-5 days ARO
Specifications
Temperature range: -32 to 100°C .Material: Polyimide film/acrylic (Kapton™ or equivalent).
Resistance tolerance: ±10%.
Minimum bend radius: 0.030" (0.8 mm).
Electrical connection options: Exposed solder pads. Options include two AWG 26 PTFE insulated leadwires 4"(100 mm) long with insulated or bare connection points.
Insulated connection wire for end-user attachment
Order loose insulated connection wires with stripped ends forfast, easy connection of heaters to your power source. TheseAWG 26 wires have high temperature PTFE insulation resistantto wear and abrasion. The insulation color is red and the stan-dard length is 4" (100 mm). Wires are sold in pairs, order onepair for each heater. Order part number AC102371.
Commercial grade polyimide heaters
Specification options
*Due to solder junctions parts are not RoHS compliant
HK5950 Base model from table
L Termination options:*S = Solder pads
L = 4" (100 mm) PTFE insulated
leadwires - lead attachment
area not insulated
P = 4" (100 mm) PTFE insulated
leadwires with insulated
connection points
HK5950L = Sample part
Base model table
Modelnumbers
Size(inches)
Size(mm)
Resistance inohms
Voltage Watt densityW/in2 (W/cm2)
Effectivearea in² (cm²)
HK5950 0.5 x 2.0 12.7 x 50.8 57.5 12 2.5 (0.39) 1.0 (6.45)
HK5951 1.0 x 1.0 25.4 x 25.4 57.5 12 2.5 (0.39) 1.0 (6.45)
HK5952 0.5 x 5.0 12.7 x 127 23.0 12 2.5 (0.39) 2.5 (16.13)
HK5953 1.0 x 3.0 25.4 x 76.2 19.2 12 2.5 (0.39) 3.0 (19.35)
HK5954 2.0 x 2.0 50.8 x 50.8 57.6 24 2.5 (0.39) 4.0 (25.81)
HK5955 3.0 x 3.0 76.2 x 76.2 25.6 24 2.5 (0.39) 9.0 (58.06)
HK5956 4.0 x 4.0 101.6 x 101.6 14.4 24 2.5 (0.39) 16.0(103.2)
HK5957 5.0 x 5.0 127 x 127 9.2 24 2.5 (0.39) 25.0 (161.29)
Commercial Grade Polyimide Heaters
Reliable heating options at an affordable price
Minco has invested in the design time and fabrication tooling soyou can jump immediately to your prototyping efforts. The following table outlines the specifications of previouslydesigned polyimide and silicone rubber Thermofoil™ heaters.
Minco's build-to-order turnaround time is typically 3 weeksdepending on quantity requirements. There is a limited availableinventory of a variety of part configurations which generallyallows us to meet your immediate delivery needs.
Contact Access: Minco Sales and Support to discuss mix andmatching heater sizes and resistance values to help satisfy performance and lead time demands.
Specification options
Technical Specifications on pages 16 (polyimide) & 20 (rubber).
Temperature sensitive elements
Heaterstats™ (page 44) require temperature sensitive heatingelements, such as those found in the “NiFe” and “Ni”columns.Their resistance increases with temperature. The resistances listed are measured at 0°C (32°F).
22
IntroductionD
esignG
uidePolyim
ideH
eatersSiliconeRub
ber
Heaters (foil)
StandardPolyim
ide&
Rubb
er
Rubb
erH
eaters(w
ire-wound)
Mica H
eatersTherm
al-Clear
Heaters
All-Polyim
ideH
eatersSensors,
Controllers &
Accessories
Reference
S a l e s a n d S u p p o r tAmericas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacific: (65) 6511 3388|
Standard Polyimide and Rubber Heaters
Types 21, 30, and 31 have lead connections on an external tab. Thetab produces negligible heat and, in most cases, need not be adheredto the heat sink. On type 21 heaters that are 0.25" (6.4 mm) wide, thetab is the same width as the heated area.
1 2 3 4
5 6 7 8
9 10
21
11 XX Y
UNHEATED TAB:AWG 30: 0.40" long × 0.25" wide (10.2 × 6.4 mm)AWG 26: 0.40" × 0.40" (10.2 × 10.2 mm)
X
X
Y
Y
30 31 XX Y
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number0.40 2.60 10.2 66.0 1 1 123 62.5 37.8 18.2 19.1 0.74 (4.77) 30 K, R 5215
0.41 4.80 10.4 121.9 6 6 100 50.1 30.2 14.5 15.5 1.40 (9.03) 26 K, R 5218
0.41 8.30 10.4 210.8 5 5 61.9 31.1 18.8 9.1 6.2 4.3 9.6 2.50 (16.13) 26 K, R 5219
How to use the table of Standard Polyimide & Silicone Rubber Heaters
Overall heater size ininches. Listed in
ascending order, firstby dimension X, then Y.Round heaters are last.
Heater type(lead exit
configuration).
Element resistanceoptions in ohms. Selectresistance to producedesired wattage withavailable voltage(see Ohm’s law).
Effective heating area.Use this value forcalculating watt
density.
Available heaterinsulation options
for this model.K=PolyimideR=rubber
*Resistance tolerance is ±10% or ±0.5, whichever is greaterRubber (HR) models not available with NiFe element
Type (configuration)
HK Insulation:HK = Polyimide
HR = Silicone rubber
5200 Model number from tables on following pages
R17.4 Heater resistance in ohms
L12 Lead length in inches12" (305 mm) is standard
Contact Minco for other lengths
A Heater backing option (see page 8)
HK HRA = No adhesive -200 to 200°C -45 to 235°C
B = PSA backing -32 to 100°C -45 to 177°C
D = Foil backing -200 to 150°C -45 to 235°C
E = Foil/Acrylic PSA -32 to 150°C -32 to 150°C
F = Foil/#12 PSA -73 to 150°C -45 to 204°C
U U = Marked for UL component recognition: uOmit for no UL marking (lower cost)
UL limits: 220°C for rubber heaters
HK5200R17.4L12AU = Sample part number
Overall heater size inmillimeters. Listed inascending order, first
by dimension X, then Y.
Temperature sensitiveelement resistance
options (at 0°C) for usewith Minco Heaterstat.Rubber (HR) models are
not available withNiFe element.
Leadwire size.Maximum current
capacities are listed onpages 17 and 20.
Base model number
23
Intr
oduc
tion
Des
ign
Gui
dePo
lyim
ide
Hea
ters
Silic
one
Rub
ber
Hea
ters
(foi
l)
Stan
dard
Poly
imid
e&
Rub
ber
Rub
ber
Hea
ters
(wire
-wou
nd)
Mic
a H
eate
rsTh
erm
al-C
lear
Hea
ters
All-
Poly
imid
eH
eate
rsSe
nsor
s,C
ontr
olle
rs &
Acc
esso
ries
Refe
renc
e
| Flexible Heaters Design Guide | www.minco.com
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5, whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number0.25 0.25 6.4 6.4 21 A 10.0 5.3 0.04 (0.26) 30 K 5565
0.25 0.50 6.4 12.7 21 A 15.0 7.9 4.3 0.08 (0.52) 30 K 5566
0.25 0.75 6.4 19.1 21 A 20.0 10.5 5.7 0.13 (0.84) 30 K 5567
0.25 1.00 6.4 25.4 21 A 25.0 13.1 7.1 3.9 0.18 (1.16) 30 K 5568
0.25 1.25 6.4 31.8 21 A 30.0 15.8 8.5 4.7 0.23 (1.48) 30 K 5569
0.25 1.50 6.4 38.1 21 A 35.0 18.4 10.0 4.7 5.4 0.27 (1.74) 30 K 5570
0.25 1.75 6.4 44.5 21 A 40.0 21.0 11.4 5.3 6.2 0.32 (2.06) 30 K 5571
0.25 2.30 6.4 58.4 6 6 17.4 9.2 5.2 0.38 (2.45) 26 K, R 5200
0.25 6.82 6.4 173.2 9 9 100 46.7 28.2 13.6 15.5 1.22 (7.87) 26 K, R 5201
0.25 7.67 6.4 194.8 8 8 143 71.7 38.1 19.1 22.2 1.15 (7.42) 30 K, R 5202
0.25 10.40 6.4 264.2 5 5 160 80.1 48.4 23.3 24.8 5.7 1.55 (10.00) 26 K, R 5203
0.27 2.00 6.9 50.8 1 1 18.9 9.5 5.7 0.35 (2.26) 26 K, R 5204
0.27 5.50 6.9 139.7 8 8 153 76.5 40.7 20.4 23.7 5.5 0.87 (5.61) 30 K 5205
0.27 6.90 6.9 175.3 1 1 220 110 65.5 32.1 34.1 7.8 1.40 (9.03) 30 K 5206
0.30 1.50 7.6 38.1 1 1 42.1 20.7 12.5 6.1 6.5 0.30 (1.94) 30 K, R 5207
0.30 3.11 7.6 79.0 1 1 44.1 22.1 13.3 6.4 6.8 0.70 (4.52) 26 K, R 5208
0.30 3.11 7.6 79.0 1 1 31.7 15.8 9.6 4.6 0.72 (4.65) 26 K, R 5209
0.34 3.47 8.6 88.1 1 1 120 56.1 33.9 16.3 18.6 0.88 (5.68) 30 K 5210
0.36 7.95 9.1 201.9 8 8 225 113 68.3 32.8 34.9 8.0 1.97 (12.71) 26 K, R 5211
0.37 6.10 9.4 154.9 1 1 73.1 36.4 22.1 10.6 11.3 1.68 (10.84) 26 K, R 5212
0.37 20.20 9.4 513.1 1 1 130 65.0 39.3 18.9 12.9 9.1 5.54 (35.74) 26 R 5213
0.40 2.60 10.2 66.0 1 1 123 62.5 37.8 18.2 19.1 0.74 (4.77) 30 K, R 5215
0.41 4.80 10.4 121.9 6 6 100 50.1 30.2 14.5 15.5 1.40 (9.03) 26 K, R 5218
0.41 8.30 10.4 210.8 5 5 61.9 31.1 18.8 9.1 6.2 4.3 9.6 2.50 (16.13) 26 K, R 5219
0.41 9.00 10.4 228.6 5 5 199 99.7 60.3 29.1 30.8 7.0 2.77 (17.87) 26 K, R 5220
0.42 2.30 10.7 58.4 1 1 50.1 26.1 15.3 7.3 7.8 0.67 (4.32) 26 K, R 5222
0.42 4.90 10.7 124.5 1 1 198 100 60.2 28.9 30.7 7.0 1.55 (10.00) 26 K 5224
0.42 7.10 10.7 180.3 1 1 322 161 85.7 42.8 49.9 11.4 2.06 (13.29) 30 K, R 5225
0.42 14.40 10.7 365.8 1 1 709 354 189 94.3 110 25.2 4.17 (26.90) 30 K 5227
0.43 3.95 10.9 100.3 8 8 238 119 63.3 31.7 36.9 8.5 1.22 (7.87) 26 K 5228
0.43 5.50 10.9 139.7 1 1 131 65.8 35.0 17.5 20.3 1.70 (10.97) 30 K, R 5229
0.43 5.90 10.9 149.9 6 6 37.3 18.8 11.3 5.4 3.7 5.8 1.87 (12.06) 26 K, R 5230
0.44 3.00 11.2 76.2 6 6 27.8 13.6 8.2 3.9 1.03 (6.65) 26 K, R 5231
0.44 3.00 11.2 76.2 6 6 45.8 22.9 13.8 6.6 7.1 1.03 (6.65) 26 K, R 5232
0.44 3.00 11.2 76.2 6 6 77.7 38.8 23.5 11.3 12.0 1.03 (6.65) 26 K, R 5233
0.45 3.88 11.4 98.6 8 8 153 76.4 40.7 20.3 23.7 5.4 1.17 (7.55) 26 K 5234
0.45 3.88 11.4 98.6 1 1 102 51.1 30.9 14.8 15.8 1.16 (7.48) 26 K, R 5235
0.45 3.88 11.4 98.6 3 3 134 67.3 40.7 19.6 20.8 1.16 (7.48) 26 K 5236
0.45 3.88 11.4 98.6 8 8 102 51.2 27.2 13.6 15.8 1.17 (7.55) 30 K, R 5237
0.46 5.10 11.7 129.5 1 1 264 132 79.9 38.4 40.9 9.4 1.77 (11.42) 26 K 5238
0.48 4.50 12.2 114.3 8 8 47.1 23.6 14.3 6.8 4.7 7.3 1.60 (10.32) 26 K, R 5239
0.48 6.28 12.2 159.5 8 8 70.2 35.1 18.7 9.3 6.2 4.7 10.9 2.20 (14.19) 26 K, R 5240
0.49 4.80 12.4 121.9 8 8 170 85.1 51.5 24.7 26.4 6.0 1.60 (10.32) 26 K, R 5241
0.50 0.50 12.7 12.7 21 A 26.5 13.9 7.5 4.1 0.19 (1.23) 30 K 5572
0.50 0.75 12.7 19.1 21 A 30.0 15.7 8.5 4.7 0.30 (1.94) 30 K, R 5573
0.50 1.00 12.7 25.4 21 A 35.0 18.3 10.0 4.6 5.4 0.41 (2.65) 30 K, R 5574
*Resistance tolerance is ±10% or ±0.5, whichever is greaterRubber (HR) models not available with NiFe element
24
IntroductionD
esignG
uidePolyim
ideH
eatersSiliconeRub
ber
Heaters (foil)
StandardPolyim
ide&
Rubb
er
Rubb
erH
eaters(w
ire-wound)
Mica H
eatersTherm
al-Clear
Heaters
All-Polyim
ideH
eatersSensors,
Controllers &
Accessories
Reference
S a l e s a n d S u p p o r tAmericas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacific: (65) 6511 3388|
Standard Polyimide and Rubber Heaters
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number0.50 1.25 12.7 31.8 21 A 40.0 20.9 11.4 5.3 6.2 0.52 (3.35) 30 K, R 5575
0.50 1.50 12.7 38.1 21 A 45.0 23.5 12.8 5.9 4.4 7.0 0.63 (4.06) 30 K, R 5576
0.50 1.75 12.7 44.5 21 A 50.0 26.1 14.2 6.6 4.9 7.8 0.74 (4.77) 30 K, R 5577
0.50 2.00 12.7 50.8 1 1 157 78.4 44.0 24.3 5.6 0.79 (5.10) 30 K, R 5160
0.50 2.50 12.7 63.5 1 1 71.1 35.1 21.3 10.3 11.0 0.84 (5.42) 26 K, R 5242
0.50 3.00 12.7 76.2 1 1 124 65.0 35.3 16.4 12.3 9.3 19.2 1.09 (7.03) 26 K, R 5594
0.50 3.77 12.7 95.8 1 1 233 117 62.1 31.1 36.1 8.3 1.43 (9.23) 30 K 5243
0.50 3.77 12.7 95.8 1 1 163 81.5 43.4 21.7 25.3 5.8 1.36 (8.77) 30 K, R 5244
0.50 4.00 12.7 101.6 1 1 78.4 39.2 22.0 12.2 1.67 (10.77) 30 K, R 5161
0.50 4.00 12.7 101.6 1 1 43.9 22.1 13.3 6.4 4.4 6.8 1.63 (10.52) 30 K, R 5245
0.50 4.00 12.7 101.6 1 1 52.7 26.4 15.9 7.7 5.2 3.6 8.2 1.63 (10.52) 30 K, R 5246
0.50 5.00 12.7 127.0 5 5 36.7 18.3 11.1 5.3 3.6 5.7 1.63 (10.52) 26 K, R 5247
0.50 5.10 12.7 129.5 8 8 126 62.5 37.8 18.2 19.5 1.90 (12.26) 30 K, R 5248
0.50 6.00 12.7 152.4 1 1 52.3 26.1 14.6 8.1 2.35 (15.16) 30 K, R 5162
0.50 7.50 12.7 190.5 1 1 53.1 26.2 16.1 7.7 5.3 3.7 8.2 2.72 (17.55) 24 K, R 5249
0.50 12.87 12.7 326.9 6 6 230 115 69.5 33.5 35.7 8.1 4.80 (30.97) 26 K, R 5250
0.50 12.87 12.7 326.9 6 6 115 57.5 34.8 16.7 11.4 8.1 17.8 4.67 (30.13) 26 K, R 5251
0.50 12.87 12.7 326.9 6 6 77.1 38.5 23.3 11.2 7.7 5.4 12.0 4.67 (30.13) 26 K, R 5252
0.50 18.50 12.7 469.9 1 1 289 145 87.7 42.1 29.1 20.3 10.1 7.20 (46.45) 26 R 5253
0.52 8.20 13.2 208.3 8 8 224 112 59.6 28.8 34.7 7.9 3.46 (22.32) 26 K, R 5254
0.53 1.00 13.5 25.4 1 1 63.2 31.6 16.8 8.4 9.8 0.39 (2.52) 30 K 5255
0.53 1.20 13.5 30.5 1 1 59.6 29.8 15.9 7.9 9.2 0.39 (2.52) 30 K 5256
0.53 2.00 13.5 50.8 2 2 135 67.6 36.1 18.1 20.9 0.79 (5.10) 30 K 5257
0.53 4.60 13.5 116.8 3 3 166 83.3 50.4 24.2 25.7 5.9 1.76 (11.35) 24 K, R 5259
0.53 4.60 13.5 116.8 3 3 95.7 56.5 28.9 13.9 14.8 1.85 (11.94) 26 K, R 5260
0.54 2.00 13.7 50.8 1 1 135 67.5 40.8 19.6 20.9 0.75 (4.84) 30 K 5261
0.54 8.10 13.7 205.7 1 1 233 117 62.1 31.1 36.1 8.2 3.34 (21.55) 26 K, R 5262
0.55 1.20 14.0 30.5 1 1 24.9 12.9 7.8 3.7 0.35 (2.26) 26 K, R 5264
0.55 6.60 14.0 167.6 1 1 107 53.9 32.6 15.7 10.7 7.5 16.6 2.79 (18.00) 26 K, R 5267
0.55 15.00 14.0 381.0 1 1 217 108 65.8 31.7 21.7 15.2 33.6 7.6 6.38 (41.16) 24 K, R 5268
0.60 9.90 15.2 251.5 1 1 229 115 69.5 33.4 22.9 16.1 35.5 8.0 4.65 (30.00) 26 K, R 5270
0.60 10.65 15.2 270.5 6 6 360 180 95.9 47.9 55.8 12.7 4.84 (31.23) 30 K, R 5271
0.65 10.75 16.5 273.1 7 7 124 64.1 37.5 18.1 12.4 8.6 19.2 5.56 (35.87) 26 K, R 5273
0.75 0.75 19.1 19.1 21 A 35.0 18.3 9.9 4.6 5.4 0.48 (3.10) 30 K, R 5578
0.75 1.00 19.1 25.4 21 A 40.0 20.9 11.4 5.2 6.2 0.65 (4.19) 30 K, R 5579
0.75 1.25 19.1 31.8 21 A 45.0 23.4 12.8 5.9 4.4 7.0 0.82 (5.29) 30 K, R 5580
0.75 1.50 19.1 38.1 21 A 50.0 26.0 14.2 6.5 4.8 7.8 0.99 (6.39) 30 K, R 5581
0.75 1.75 19.1 44.5 21 A 55.0 28.6 15.6 7.2 5.3 8.5 1.17 (7.55) 30 K, R 5582
0.75 1.85 19.1 47.0 1 1 50.1 25.2 15.2 7.3 5.1 3.5 7.8 1.02 (6.58) 26 K, R 5274
0.75 2.00 19.1 50.8 21 A 124 64.9 35.3 16.4 12.2 9.2 19.2 1.34 (8.65) 26 K, R 5595
0.75 2.50 19.1 63.5 2 2 43.5 21.8 13.2 6.3 4.3 6.7 1.37 (8.84) 26 K, R 5275
0.75 3.00 19.1 76.2 1 1 144 71.7 43.6 21.1 22.3 1.72 (11.10) 26 K, R 5276
0.75 3.00 19.1 76.2 1 1 18.1 8.5 5.3 1.14 (7.35) 24 K, R 5277
0.75 3.25 19.1 82.6 6 6 160 80.1 48.5 23.3 24.8 5.6 1.95 (12.58) 26 K, R 5278
0.75 4.00 19.1 101.6 1 1 36.1 17.7 10.7 5.1 3.5 5.6 2.41 (15.55) 26 K, R 5279
0.75 4.00 19.1 101.6 1 1 24.5 11.1 6.9 3.3 1.69 (10.90) 24 K, R 5280
25
Intr
oduc
tion
Des
ign
Gui
dePo
lyim
ide
Hea
ters
Silic
one
Rub
ber
Hea
ters
(foi
l)
Stan
dard
Poly
imid
e&
Rub
ber
Rub
ber
Hea
ters
(wire
-wou
nd)
Mic
a H
eate
rsTh
erm
al-C
lear
Hea
ters
All-
Poly
imid
eH
eate
rsSe
nsor
s,C
ontr
olle
rs &
Acc
esso
ries
Refe
renc
e
| Flexible Heaters Design Guide | www.minco.com
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5 , whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number0.75 4.95 19.1 125.7 8 8 267 134 71.1 35.6 41.4 9.4 3.06 (19.74) 30 K 5281
0.75 5.00 19.1 127.0 1 1 30.6 14.1 8.7 4.2 2.24 (14.45) 24 K, R 5282
0.75 6.00 19.1 152.4 1 1 36.7 16.6 10.3 5.1 5.7 2.79 (18.00) 24 K, R 5283
0.75 7.00 19.1 177.8 1 1 38.8 19.4 12.1 5.5 4.1 6.0 3.34 (21.55) 24 K, R 5284
0.75 8.00 19.1 203.2 1 1 48.7 22.1 13.7 6.4 4.4 3.3 7.5 3.89 (25.10) 24 K, R 5285
0.75 9.00 19.1 228.6 1 1 54.7 25.1 15.6 7.1 5.1 3.6 8.5 4.44 (28.65) 24 K, R 5286
0.75 10.00 19.1 254.0 1 1 60.8 27.7 17.2 7.7 5.5 4.1 9.4 4.99 (32.19) 24 K, R 5287
0.75 11.00 19.1 279.4 1 1 66.9 30.4 18.8 8.7 6.1 4.5 10.4 5.54 (35.74) 24 K, R 5288
0.75 11.00 19.1 279.4 1 1 200 100 60.5 29.1 19.9 13.9 31.0 7.0 6.32 (40.77) 24 K, R 5289
0.75 12.00 19.1 304.8 1 1 72.6 33.1 20.5 9.1 6.4 4.7 11.3 6.09 (39.29) 24 K, R 5290
0.78 2.76 19.8 70.1 6 6 83.7 41.9 22.3 11.1 7.4 5.6 13.0 1.79 (11.55) 30 K, R 5292
0.80 1.55 20.3 39.4 2 2 313 156 83.1 41.6 48.5 11.3 0.90 (5.81) 30 K 5294
0.80 1.55 20.3 39.4 2 2 105 52.5 27.9 14.0 16.3 0.94 (6.06) 30 K, R 5295
0.80 2.75 20.3 69.9 8 8 39.7 19.8 12.1 5.7 3.9 6.2 1.52 (9.81) 26 K, R 5296
0.80 6.00 20.3 152.4 8 8 123 61.8 37.4 17.9 12.3 8.6 19.1 4.23 (27.29) 26 K, R 5297
0.80 8.10 20.3 205.7 8 8 21.5 11.2 6.9 5.39 (34.77) 26 K, R 5298
0.80 11.50 20.3 292.1 8 8 166 83.2 50.3 24.2 16.5 11.6 25.7 5.8 7.52 (48.52) 24 K, R 5299
0.80 14.25 20.3 362.0 8 8 206 103 62.4 30.1 20.5 14.4 31.9 7.2 9.38 (60.52) 24 K, R 5300
0.81 4.81 20.6 122.2 2 2 64.7 32.9 19.6 9.4 6.4 4.5 10.0 3.33 (21.48) 26 K, R 5301
0.82 2.46 20.8 62.5 9 9 243 121 64.5 32.3 37.7 8.6 1.66 (10.71) 30 K, R 5302
0.85 1.00 21.6 25.4 6 6 70.2 35.1 20.6 9.9 10.9 0.60 (3.87) 30 K, R 5303
0.85 2.48 21.6 63.0 9 9 268 134 71.3 35.7 41.5 9.5 1.65 (10.65) 30 K 5304
0.85 4.90 21.6 124.5 3 3 207 104 55.1 27.5 32.1 7.3 3.60 (23.23) 26 K, R 5305
0.86 15.80 21.8 401.3 1 1 140 70.1 42.3 20.3 13.9 9.7 21.7 11.10 (71.61) 24 K, R 5306
0.87 8.65 22.1 219.7 8 8 561 281 149 74.7 87.0 19.8 6.39 (41.23) 26 K, R 5307
0.87 14.85 22.1 377.2 8 8 131 65.4 39.6 19.1 13.1 9.1 20.3 10.28 (66.32) 24 K, R 5308
0.88 5.35 22.4 135.9 8 8 62.6 31.3 18.9 9.1 6.2 4.4 9.7 3.85 (24.84) 26 K, R 5309
0.90 4.95 22.9 125.7 3 3 207 103 62.6 30.1 32.1 7.3 3.52 (22.71) 26 K, R 5310
0.94 3.90 23.9 99.1 9 9 119 59.6 31.8 15.9 10.6 7.9 18.4 2.94 (18.97) 30 K, R 5311
0.96 1.48 24.4 37.6 3 3 76.1 38.1 20.2 10.1 11.8 1.10 (7.10) 30 K, R 5312
0.97 1.21 24.6 30.7 3 3 84.3 42.2 22.4 11.2 13.1 0.90 (5.81) 30 K, R 5313
0.97 2.96 24.6 75.2 2 2 303 151 80.5 40.3 47.0 10.7 2.45 (15.81) 30 K, R 5314
0.98 1.48 24.9 37.6 6 6 80.1 39.7 24.1 11.6 12.4 1.13 (7.29) 26 K, R 5315
0.98 2.75 24.9 69.9 1 1 206 103 61.7 29.7 31.9 7.3 2.07 (13.35) 26 K, R 5316
1.00 1.00 25.4 25.4 1 1 157 78.4 44.0 24.3 5.6 0.82 (5.29) 30 K, R 5163
1.00 1.00 25.4 25.4 1 1 52.1 26.1 15.7 7.6 8.1 0.65 (4.19) 26 K, R 5318
1.00 1.00 25.4 25.4 21 A 70.0 36.6 19.9 9.2 6.8 5.2 10.9 0.88 (5.68) 30 K, R 5583
1.00 1.25 25.4 31.8 21 A 65.0 33.9 18.5 8.5 6.3 4.7 10.1 1.12 (7.23) 30 K, R 5584
1.00 1.50 25.4 38.1 21 A 75.0 39.1 21.3 9.8 7.3 5.4 11.6 1.35 (8.71) 30 K, R 5585
1.00 1.75 25.4 44.5 21 A 100 52.2 28.4 13.1 9.7 7.3 15.5 1.59 (10.26) 30 K, R 5586
1.00 2.00 25.4 50.8 1 1 78.4 39.2 22.0 12.2 1.76 (11.35) 30 K, R 5164
1.00 2.00 25.4 50.8 1 1 14.6 7.3 4.5 1.04 (6.71) 24 K, R 5319
1.00 2.30 25.4 58.4 3 3 220 110 58.4 29.2 34.1 7.8 1.82 (11.74) 30 K, R 5320
1.00 2.50 25.4 63.5 1 1 146 72.1 43.1 20.7 22.6 5.1 1.89 (12.19) 26 K, R 5321
1.00 2.50 25.4 63.5 1 1 107 53.3 32.3 15.5 16.6 1.89 (12.19) 26 K, R 5322
1.00 3.00 25.4 76.2 1 1 52.3 26.1 14.6 8.1 2.70 (17.42) 30 K, R 5165
26
IntroductionD
esignG
uidePolyim
ideH
eatersSiliconeRub
ber
Heaters (foil)
StandardPolyim
ide&
Rubb
er
Rubb
erH
eaters(w
ire-wound)
Mica H
eatersTherm
al-Clear
Heaters
All-Polyim
ideH
eatersSensors,
Controllers &
Accessories
Reference
S a l e s a n d S u p p o r tAmericas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacific: (65) 6511 3388|
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5 , whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number1.00 3.00 25.4 76.2 1 1 23.9 10.7 6.6 1.84 (11.87) 24 K, R 5323
1.00 3.00 25.4 76.2 1 1 58.0 26.6 16.1 7.7 5.3 3.7 9.0 2.30 (14.84) 26 K, R 5324
1.00 3.00 25.4 76.2 1 1 36.4 17.9 10.8 5.2 3.6 5.6 2.30 (14.84) 26 K, R 5325
1.00 3.62 25.4 91.9 3 3 61.1 30.6 18.5 8.9 6.1 4.2 9.5 2.97 (19.16) 26 K, R 5326
1.00 3.72 25.4 94.5 3 3 445 223 118 59.2 69.0 15.8 3.15 (20.32) 30 K, R 5327
1.00 3.72 25.4 94.5 3 3 389 195 118 56.7 60.3 13.8 3.06 (19.74) 26 K, R 5328
1.00 3.82 25.4 97.0 2 2 160 80.1 48.5 23.3 15.9 11.2 24.8 5.6 3.29 (21.23) 26 K, R 5329
1.00 4.00 25.4 101.6 1 1 83.3 42.7 25.2 12.1 8.3 5.8 12.9 3.33 (21.48) 26 K, R 5330
1.00 4.00 25.4 101.6 1 1 30.8 13.9 8.6 4.2 2.64 (17.03) 24 K, R 5331
1.00 4.75 25.4 120.7 6 6 302 151 91.6 44.1 46.8 10.6 4.29 (27.68) 24 K, R 5332
1.00 4.75 25.4 120.7 6 6 266 133 80.5 38.7 41.2 9.4 4.05 (26.13) 26 K, R 5333
1.00 5.00 25.4 127.0 1 1 529 264 148 82.0 18.7 4.41 (28.45) 30 K, R 5166
1.00 5.00 25.4 127.0 1 1 38.1 17.2 10.7 5.1 5.9 4.34 (28.00) 24 K, R 5334
1.00 6.00 25.4 152.4 1 1 45.3 20.8 12.9 5.8 4.1 7.0 4.24 (27.35) 24 K, R 5335
1.00 6.00 25.4 152.4 2 2 162 80.9 48.9 23.5 16.1 11.3 25.1 5.7 5.13 (33.10) 26 K, R 5336
1.00 7.00 25.4 177.8 1 1 52.1 24.1 14.9 6.8 4.7 3.5 8.1 5.04 (32.52) 24 K, R 5337
1.00 7.00 25.4 177.8 1 1 86.1 43.1 26.1 12.3 8.5 6.1 13.3 6.19 (39.94) 26 K, R 5338
1.00 7.05 25.4 179.1 1 1 111 55.7 33.7 16.2 11.1 7.7 17.2 6.12 (39.48) 26 K, R 5339
1.00 8.00 25.4 203.2 1 1 58.9 27.5 17.1 7.7 5.4 3.9 9.1 5.84 (37.68) 24 K, R 5340
1.00 9.00 25.4 228.6 1 1 66.1 30.4 18.8 8.7 5.9 4.4 10.2 6.64 (42.84) 24 K, R 5341
1.00 10.00 25.4 254.0 1 1 264 132 74.1 40.9 9.2 8.96 (57.81) 30 K, R 5167
1.00 10.00 25.4 254.0 1 1 73.4 34.1 21.1 9.4 6.6 4.9 11.4 7.44 (48.00) 24 K, R 5342
1.00 11.00 25.4 279.4 1 1 79.8 37.2 23.1 10.3 7.2 5.4 12.4 8.24 (53.16) 24 K, R 5343
1.00 12.00 25.4 304.8 1 1 86.5 40.3 24.9 11.1 7.7 5.8 13.4 9.04 (58.32) 24 K, R 5344
1.00 12.00 25.4 304.8 3 3 163 82.1 49.6 23.8 16.3 11.4 25.3 5.7 10.53 (67.94) 24 K, R 5345
1.00 12.00 25.4 304.8 1 1 1063 531 321 154 165 37.6 10.53 (67.94) 26 K, R 5346
1.00 12.10 25.4 307.3 1 1 155 76.6 46.3 22.3 15.2 10.6 24.0 5.4 10.62 (68.52) 26 K, R 5347
1.00 15.00 25.4 381.0 1 1 176 88.2 49.4 27.3 6.1 13.51 (87.16) 30 K, R 5168
1.00 19.00 25.4 482.6 1 1 121 60.8 36.8 17.7 12.1 8.5 13.88 (89.55) 24 R 5348
1.00 22.06 25.4 560.3 1 1 93.1 46.5 24.8 12.4 8.3 6.2 18.90 (121.94) 24 R 5349
1.02 10.00 25.9 254.0 5 5 946 473 252 126 147 33.5 8.60 (55.48) 24 K, R 5350
1.04 2.76 26.4 70.1 5 5 262 131 69.6 34.8 40.6 9.3 2.04 (13.16) 26 K, R 5351
1.04 4.35 26.4 110.5 1 1 87.6 43.8 23.3 11.7 7.8 5.8 13.6 4.06 (26.19) 26 K, R 5352
1.04 7.76 26.4 197.1 8 8 1321 660 352 176 205 47.1 6.80 (43.87) 30 K 5353
1.05 4.04 26.7 102.6 8 8 243 122 64.8 32.4 37.7 8.5 3.65 (23.55) 30 K, R 5354
1.05 4.65 26.7 118.1 8 8 152 74.1 44.4 21.3 23.6 5.3 4.05 (26.13) 26 K, R 5355
1.05 5.60 26.7 142.2 7 7 440 220 133 64.1 68.2 15.5 5.04 (32.52) 26 K, R 5356
1.05 9.70 26.7 246.4 1 1 276 138 73.4 36.7 24.5 18.3 42.8 9.6 8.80 (56.77) 24 K, R 5357
1.07 4.05 27.2 102.9 8 8 103 51.3 27.3 13.7 9.1 6.8 16.0 3.67 (23.68) 30 K, R 5358
1.10 4.00 27.9 101.6 1 1 600 300 181 87.3 93.0 21.3 3.75 (24.19) 30 K 5359
1.10 4.00 27.9 101.6 1 1 394 197 119 57.4 61.1 13.9 3.70 (23.87) 30 K, R 5360
1.10 18.50 27.9 469.9 3 3 350 175 106 50.1 34.8 24.3 12.2 17.64 (113.81) 24 R 5361
1.13 3.51 28.7 89.2 8 8 107 53.4 28.4 14.2 9.5 6.6 16.6 3.43 (22.13) 30 K, R 5362
1.17 1.91 29.7 48.5 2 2 125 62.5 37.8 18.2 19.4 1.79 (11.55) 26 K, R 5364
1.20 2.76 30.5 70.1 1 1 275 136 82.7 39.8 42.6 9.7 2.86 (18.45) 30 K, R 5366
1.20 3.40 30.5 86.4 7 7 92.0 45.7 26.6 13.3 9.1 6.4 14.3 3.41 (22.00) 26 K, R 5367
27
Intr
oduc
tion
Des
ign
Gui
dePo
lyim
ide
Hea
ters
Silic
one
Rub
ber
Hea
ters
(foi
l)
Stan
dard
Poly
imid
e&
Rub
ber
Rub
ber
Hea
ters
(wire
-wou
nd)
Mic
a H
eate
rsTh
erm
al-C
lear
Hea
ters
All-
Poly
imid
eH
eate
rsSe
nsor
s,C
ontr
olle
rs &
Acc
esso
ries
Refe
renc
e
| Flexible Heaters Design Guide | www.minco.com
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5 , whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number1.22 2.24 31.0 56.9 8 8 111 55.5 29.5 14.8 9.8 7.4 17.2 2.33 (15.03) 30 K, R 5368
1.23 2.48 31.2 63.0 2 2 101 50.8 27.1 13.5 9.4 6.7 15.7 2.60 (16.77) 30 K, R 5369
1.24 1.80 31.5 45.7 2 2 298 148 90.1 43.3 46.2 10.6 1.90 (12.26) 30 K 5370
1.25 1.25 31.8 31.8 21 A 100 52.2 28.4 13.1 9.7 7.3 15.5 1.42 (9.16) 30 K, R 5587
1.25 1.50 31.8 38.1 21 A 125 65.3 35.5 16.4 12.2 9.2 19.4 1.71 (11.03) 30 K, R 5588
1.25 1.75 31.8 44.5 21 A 150 78.4 42.6 19.7 14.6 11.0 23.3 5.3 2.01 (12.97) 30 K, R 5589
1.25 6.30 31.8 160.0 1 1 136 68.2 41.3 19.8 13.6 9.5 21.1 6.84 (44.13) 24 K, R 5371
1.25 8.80 31.8 223.5 1 1 51.9 25.9 15.7 7.5 5.1 3.6 8.0 9.86 (63.61) 24 K, R 5372
1.25 15.00 31.8 381.0 1 1 219 109 66.5 32.1 21.9 15.3 33.9 7.6 15.79 (101.87) 24 K, R 5373
1.35 5.60 34.3 142.2 3 3 876 438 265 127 136 31.1 6.57 (42.39) 30 K 5374
1.37 5.80 34.8 147.3 1 1 250 125 75.8 36.5 24.9 17.5 38.8 8.7 7.15 (46.13) 26 K, R 5375
1.38 2.75 35.1 69.9 2 2 305 152 92.1 44.2 47.3 10.8 3.21 (20.71) 26 K, R 5376
1.40 2.34 35.6 59.4 1 1 197 98.7 52.5 26.3 17.5 13.1 30.5 6.9 2.90 (18.71) 30 K, R 5377
1.40 6.30 35.6 160.0 8 8 771 386 205 103 120 27.2 8.08 (52.13) 30 K, R 5378
1.45 2.40 36.8 61.0 8 8 106 53.4 32.3 15.5 10.6 7.4 16.4 2.90 (18.71) 26 K, R 5379
1.45 8.15 36.8 207.0 8 8 474 237 126 63.1 42.1 31.5 73.5 16.6 10.52 (67.87) 24 K, R 5380
1.48 10.10 37.6 256.5 1 1 126 62.9 33.5 16.7 11.2 8.4 19.5 13.40 (86.45) 24 K, R 5381
1.50 1.50 38.1 38.1 21 A 150 78.3 42.6 19.7 14.6 11.0 23.3 5.3 2.07 (13.35) 30 K, R 5590
1.50 1.75 38.1 44.5 21 A 175 91.4 49.7 23.0 17.1 12.9 27.1 6.2 2.43 (15.68) 30 K, R 5591
1.50 2.00 38.1 50.8 1 1 14.8 7.2 4.5 1.84 (11.87) 24 K, R 5382
1.50 3.00 38.1 76.2 1 1 21.8 10.7 6.6 3.14 (20.26) 24 K, R 5383
1.50 4.00 38.1 101.6 1 1 29.1 14.4 8.8 4.3 4.44 (28.65) 24 K, R 5384
1.50 4.10 38.1 104.1 2 2 103 51.7 27.5 13.7 9.2 6.9 16.0 4.00 (25.81) 30 K, R 5385
1.50 5.00 38.1 127.0 1 1 36.2 17.9 10.9 5.1 3.4 5.6 5.74 (37.03) 24 K, R 5386
1.50 6.00 38.1 152.4 1 1 43.3 21.7 13.2 6.2 4.2 6.7 7.04 (45.42) 24 K, R 5387
1.50 6.42 38.1 163.1 8 8 140 70.2 37.4 18.7 21.7 7.70 (49.68) 30 K, R 5388
1.50 6.42 38.1 163.1 8 8 1317 659 350 175 204 46.8 8.50 (54.84) 30 K, R 5389
1.50 7.00 38.1 177.8 1 1 50.1 25.1 15.2 7.2 4.7 3.5 7.8 8.34 (53.81) 24 K, R 5390
1.50 8.00 38.1 203.2 1 1 57.1 28.7 17.5 8.1 5.3 3.9 8.9 9.64 (62.19) 24 K, R 5391
1.50 8.05 38.1 204.5 2 2 304 152 92.1 44.3 30.3 21.2 47.1 10.6 10.80 (69.68) 26 K, R 5392
1.50 9.00 38.1 228.6 1 1 64.1 32.2 19.6 8.9 6.1 4.4 9.9 10.94 (70.58) 24 K, R 5393
1.50 10.00 38.1 254.0 1 1 71.4 35.7 21.8 10.1 6.7 4.9 11.1 12.24 (78.97) 24 K, R 5394
1.50 11.00 38.1 279.4 1 1 78.5 39.1 23.9 10.9 7.3 5.3 12.2 13.54 (87.35) 24 K, R 5395
1.50 11.00 38.1 279.4 1 1 391 180 118 57.1 38.9 27.3 60.6 13.6 14.77 (95.29) 24 K, R 5396
1.50 12.00 38.1 304.8 1 1 85.6 42.8 25.8 11.8 7.8 5.8 13.3 14.84 (95.74) 24 K, R 5397
1.53 3.05 38.9 77.5 8 8 176 88.4 53.4 25.7 17.6 12.3 27.3 6.2 3.89 (25.10) 26 K, R 5398
1.55 3.05 39.4 77.5 1 1 130 65.3 39.5 19.1 13.1 9.1 20.2 4.06 (26.19) 26 K, R 5399
1.61 2.15 40.9 54.6 1 1 205 102 54.5 27.3 31.8 7.2 3.00 (19.35) 30 K, R 5400
1.62 2.77 41.1 70.4 1 1 166 81.1 48.6 23.3 15.9 11.2 25.7 5.8 3.95 (25.48) 30 K, R 5401
1.65 3.00 41.9 76.2 2 2 128 64.1 38.8 18.3 12.8 8.9 19.8 4.50 (29.03) 30 K, R 5402
1.65 5.00 41.9 127.0 1 1 162 81.1 48.9 23.5 16.1 11.3 25.1 5.6 7.44 (48.00) 26 K, R 5403
1.70 5.10 43.2 129.5 1 1 580 290 154 77.2 89.9 20.4 7.77 (50.13) 24 K, R 5404
1.75 1.75 44.5 44.5 21 A 200 104 56.8 26.3 19.5 14.7 31.0 7.0 2.86 (18.45) 30 K, R 5592
1.75 2.73 44.5 69.3 2 2 159 79.5 48.1 23.1 15.8 11.1 24.6 5.6 3.77 (24.32) 26 K, R 5405
1.76 4.79 44.7 121.7 1 1 330 165 87.9 43.9 29.3 22.1 51.2 11.6 7.56 (48.77) 30 K, R 5406
1.78 4.30 45.2 109.2 1 1 737 369 196 98.1 114 26.1 6.66 (42.97) 30 K, R 5407
28
IntroductionD
esignG
uidePolyim
ideH
eatersSiliconeRub
ber
Heaters (foil)
StandardPolyim
ide&
Rubb
er
Rubb
erH
eaters(w
ire-wound)
Mica H
eatersTherm
al-Clear
Heaters
All-Polyim
ideH
eatersSensors,
Controllers &
Accessories
Reference
S a l e s a n d S u p p o r tAmericas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacific: (65) 6511 3388|
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5 , whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number1.78 5.28 45.2 134.1 1 1 588 294 156 78.2 91.1 20.7 8.34 (53.81) 30 K, R 5408
1.80 1.80 45.7 45.7 3 3 251 126 66.8 33.4 38.9 8.9 2.70 (17.42) 30 K, R 5409
1.88 5.75 47.8 146.1 1 1 288 144 86.9 41.7 28.6 20.1 44.6 10.1 9.68 (62.45) 24 K, R 5410
1.90 3.16 48.3 80.3 6 6 236 118 62.8 31.4 20.9 15.7 36.6 8.3 5.48 (35.35) 26 K, R 5411
1.92 4.45 48.8 113.0 8 8 348 174 92.5 46.3 30.8 23.1 53.9 12.2 7.69 (49.61) 26 K, R 5412
1.94 5.29 49.3 134.4 6 6 508 254 135 67.6 45.1 31.6 78.7 17.8 9.38 (60.52) 30 K, R 5413
1.96 3.77 49.8 95.8 1 1 749 374 199 99.6 116 26.5 6.83 (44.06) 30 K, R 5414
1.97 2.16 50.0 54.9 3 3 112 56.3 34.1 16.4 11.2 7.8 17.4 3.79 (24.45) 26 K, R 5415
1.98 3.82 50.3 97.0 1 1 752 376 200 98.9 117 26.6 6.75 (43.55) 30 K, R 5416
2.00 2.00 50.8 50.8 1 1 661 331 185 102 23.6 3.59 (23.16) 30 K, R 5169
2.00 2.00 50.8 50.8 1 1 36.1 17.8 10.9 5.3 5.6 2.82 (18.19) 24 K, R 5417
2.00 2.60 50.8 66.0 7 7 344 172 104 51.8 53.3 12.1 4.75 (30.65) 26 K, R 5418
2.00 3.00 50.8 76.2 1 1 441 220 123 68.4 15.5 5.50 (35.48) 30 K, R 5170
2.00 3.00 50.8 76.2 1 1 53.3 25.9 15.9 7.5 5.4 3.6 8.3 4.62 (29.81) 24 K, R 5419
2.00 3.00 50.8 76.2 7 7 33.3 15.6 9.8 4.5 5.2 4.54 (29.29) 24 K, R 5463
2.00 3.25 50.8 82.6 6 6 86.6 43.3 26.2 12.6 8.6 6.1 13.4 5.60 (36.13) 24 K, R 5420
2.00 3.25 50.8 82.6 6 6 75.6 37.8 22.8 10.9 7.5 5.3 11.7 5.50 (35.48) 26 K, R 5421
2.00 4.00 50.8 101.6 1 1 331 165 92.7 51.3 11.6 7.41 (47.81) 30 K, R 5171
2.00 4.00 50.8 101.6 1 1 70.1 34.6 21.2 10.4 6.9 4.8 10.9 6.73 (43.42) 24 K, R 5422
2.00 4.00 50.8 101.6 7 7 23.7 11.6 7.3 6.34 (40.90) 24 K, R 5487
2.00 5.00 50.8 127.0 1 1 88.1 43.2 26.2 13.1 8.6 5.9 13.7 8.22 (53.03) 24 K, R 5423
2.00 5.00 50.8 127.0 7 7 23.9 13.1 8.8 4.3 8.14 (52.52) 24 K, R 5506
2.00 6.00 50.8 152.4 1 1 220 110 61.6 34.1 7.7 11.23 (72.45) 30 K, R 5172
2.00 6.00 50.8 152.4 1 1 104 51.8 31.9 15.1 9.8 7.1 16.1 10.02 (64.65) 24 K, R 5424
2.00 6.05 50.8 153.7 1 1 99.7 49.9 30.2 14.5 9.9 6.9 15.5 11.00 (70.97) 24 K, R 5425
2.00 7.00 50.8 177.8 1 1 120 60.4 36.5 17.5 11.2 8.3 18.6 11.82 (76.26) 24 K, R 5426
2.00 8.00 50.8 203.2 1 1 137 68.9 41.9 20.1 12.9 9.4 21.2 13.62 (87.87) 24 K, R 5427
2.00 9.00 50.8 228.6 1 1 154 77.7 46.8 21.6 14.3 10.6 23.9 5.3 15.42 (99.48) 24 K, R 5428
2.00 10.00 50.8 254.0 1 1 171 85.8 52.1 23.8 16.1 11.6 26.5 5.9 17.22 (111.10) 24 K, R 5429
2.00 10.00 50.8 254.0 6 6 320 160 96.8 46.5 31.8 23.3 49.6 11.1 18.20 (117.42) 26 K, R 5430
2.00 11.00 50.8 279.4 1 1 188 94.1 57.1 26.4 17.7 13.1 29.1 6.5 19.02 (122.71) 24 K, R 5431
2.00 12.00 50.8 304.8 1 1 220 110 61.6 28.6 34.1 7.6 22.69 (146.39) 24 K, R 5173
2.00 12.00 50.8 304.8 1 1 206 102 61.9 28.5 18.8 14.1 31.9 7.2 20.82 (134.32) 24 K, R 5432
2.00 12.00 50.8 304.8 1 1 442 221 134 63.5 44.1 30.8 68.5 15.4 21.80 (140.64) 24 K, R 5433
2.05 2.70 52.1 68.6 8 8 725 362 219 97.3 112 25.7 5.19 (33.48) 30 K 5434
2.15 2.55 54.6 64.8 2 2 123 62.1 37.3 17.9 12.3 8.6 19.1 5.05 (32.58) 26 K, R 5435
2.17 3.80 55.1 96.5 1 1 681 340 181 90.6 106 24.0 7.20 (46.45) 30 K, R 5436
2.25 4.00 57.2 101.6 1 1 284 142 86.1 41.4 28.3 19.8 44.0 9.9 7.70 (49.68) 26 K, R 5437
2.25 4.50 57.2 114.3 6 6 140 70.3 42.5 20.4 14.1 9.8 21.7 8.82 (56.90) 24 K, R 5438
2.25 5.25 57.2 133.4 6 6 142 70.9 42.9 20.6 14.2 9.9 22.0 10.53 (67.94) 24 K, R 5439
2.25 5.25 57.2 133.4 6 6 160 80.1 48.6 23.4 15.9 11.2 24.8 5.6 10.40 (67.10) 24 K, R 5440
2.25 6.28 57.2 159.5 8 8 364 182 110 53.1 36.3 25.4 56.4 12.7 12.52 (80.77) 26 K, R 5441
2.30 9.07 58.4 230.4 6 6 1016 508 270 135 90.1 67.6 157 35.6 19.70 (127.10) 24 K, R 5443
2.35 4.10 59.7 104.1 7 7 168 84.1 50.9 24.4 16.7 11.7 26.0 5.9 8.58 (55.35) 24 K, R 5444
2.45 6.07 62.2 154.2 8 8 861 431 229 115 133 30.3 14.00 (90.32) 24 K, R 5445
2.50 3.00 63.5 76.2 1 1 421 210 127 61.2 65.3 14.8 6.40 (41.29) 26 K, R 5446
29
Intr
oduc
tion
Des
ign
Gui
dePo
lyim
ide
Hea
ters
Silic
one
Rub
ber
Hea
ters
(foi
l)
Stan
dard
Poly
imid
e&
Rub
ber
Rub
ber
Hea
ters
(wire
-wou
nd)
Mic
a H
eate
rsTh
erm
al-C
lear
Hea
ters
All-
Poly
imid
eH
eate
rsSe
nsor
s,C
ontr
olle
rs &
Acc
esso
ries
Refe
renc
e
| Flexible Heaters Design Guide | www.minco.com
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5 , whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number2.50 3.00 63.5 76.2 1 1 290 145 87.9 42.2 28.9 20.2 45.0 10.2 6.90 (44.52) 26 K, R 5447
2.50 4.00 63.5 101.6 1 1 576 288 174 83.8 89.3 20.2 8.90 (57.42) 30 K, R 5448
2.50 4.04 63.5 102.6 1 1 703 351 187 93.5 109 24.8 9.35 (60.32) 24 K, R 5449
2.50 5.00 63.5 127.0 1 1 231 115 69.9 33.6 22.9 16.1 35.8 8.0 11.30 (72.90) 26 K, R 5450
2.50 6.00 63.5 152.4 3 3 206 103 62.3 30.1 20.5 14.3 31.9 7.2 13.60 (87.74) 26 K, R 5451
2.50 8.00 63.5 203.2 1 1 315 157 95.3 45.8 31.3 21.9 48.8 11.0 18.70 (120.64) 26 K, R 5452
2.50 11.30 63.5 287.0 1 1 2341 1170 623 311 363 82.6 25.70 (165.81) 24 K, R 5453
2.50 11.42 63.5 290.1 1 1 2089 1045 556 278 324 73.6 26.40 (170.32) 24 K, R 5454
2.53 3.05 64.3 77.5 6 6 93.7 47.1 28.3 13.6 9.3 6.5 14.5 7.17 (46.26) 26 K, R 5455
2.55 3.05 64.8 77.5 8 8 165 82.9 50.1 24.1 16.4 11.5 25.6 5.8 7.00 (45.16) 30 K, R 5456
2.68 3.44 68.1 87.4 2 2 72.6 36.3 21.9 10.6 7.2 5.1 11.3 7.64 (49.29) 26 K, R 5457
2.75 12.00 69.9 304.8 1 1 243 121 73.6 35.4 24.2 16.9 37.7 8.4 30.90 (199.35) 24 K, R 5458
2.81 2.94 71.4 74.7 2 2 253 126 76.7 36.9 25.2 17.7 39.2 8.8 7.45 (48.06) 26 K, R 5459
2.87 16.41 72.9 416.8 6 6 1648 824 438 219 146 110 57.6 45.30 (292.26) 24 R 5460
2.92 6.82 74.2 173.2 3 3 713 357 190 94.8 63.2 47.4 111 24.9 18.50 (119.35) 24 K, R 5461
2.92 6.82 74.2 173.2 1 1 1566 784 474 228 243 55.2 18.50 (119.35) 26 K, R 5462
3.00 3.00 76.2 76.2 1 1 294 147 82.3 45.6 10.3 8.41 (54.26) 30 K, R 5174
3.00 3.00 76.2 76.2 1 1 46.5 23.3 14.6 6.4 4.9 7.2 7.34 (47.35) 24 K, R 5464
3.00 3.10 76.2 78.7 1 1 44.4 22.2 13.4 6.5 4.4 6.9 7.98 (51.48) 24 K, R 5465
3.00 4.00 76.2 101.6 1 1 62.1 30.9 19.4 8.6 5.7 4.1 9.6 10.14 (65.42) 24 K, R 5466
3.00 4.00 76.2 101.6 7 7 35.1 17.1 10.8 4.6 5.4 10.14 (65.42) 24 K, R 5488
3.00 5.00 76.2 127.0 1 1 176 88.2 49.4 27.3 6.1 14.23 (91.81) 30 K, R 5175
3.00 5.00 76.2 127.0 1 1 77.7 38.7 24.2 10.3 7.1 5.1 12.0 12.94 (83.48) 24 K, R 5467
3.00 5.00 76.2 127.0 7 7 36.1 19.5 12.6 5.9 3.7 5.6 12.94 (83.48) 24 K, R 5507
3.00 6.00 76.2 152.4 1 1 93.8 46.1 29.1 12.9 8.6 6.1 14.5 15.74 (101.55) 24 K, R 5468
3.00 7.00 76.2 177.8 1 1 109 53.4 33.9 14.3 10.1 7.1 16.9 18.54 (119.61) 24 K, R 5469
3.00 8.00 76.2 203.2 1 1 125 60.9 38.8 16.1 11.4 8.1 19.4 21.34 (137.68) 24 K, R 5470
3.00 9.00 76.2 228.6 1 1 141 68.3 43.5 18.9 12.9 9.1 21.9 24.14 (155.74) 24 K, R 5471
3.00 9.00 76.2 228.6 1 1 407 203 123 59.2 40.5 28.3 63.1 14.2 25.50 (164.52) 26 K, R 5472
3.00 10.00 76.2 254.0 1 1 340 190 88.2 67.9 53.8 103 23.1 28.75 (185.48) 24 K, R 5176
3.00 10.00 76.2 254.0 1 1 156 75.8 48.3 20.3 14.9 10.2 24.2 5.4 26.94 (173.81) 24 K, R 5473
3.00 11.00 76.2 279.4 1 1 172 83.6 53.1 22.3 15.7 11.1 26.7 6.0 29.74 (191.87) 24 K, R 5474
3.00 12.00 76.2 304.8 1 1 188 91.1 57.7 23.9 16.7 12.1 29.1 6.5 32.54 (209.94) 24 K, R 5475
3.00 15.00 76.2 381.0 1 1 226 126 58.8 45.3 35.9 68.2 15.3 43.30 (279.35) 24 K, R 5177
3.03 3.03 77.0 77.0 3 3 1317 658 350 175 204 46.8 8.34 (53.81) 30 K 5476
3.10 4.10 78.7 104.1 1 1 306 153 92.7 43.8 18.1 12.7 47.4 10.7 11.40 (73.55) 26 K, R 5477
3.10 6.10 78.7 154.9 1 1 88.6 44.4 26.9 12.9 8.8 6.2 13.7 16.60 (107.10) 24 K, R 5478
3.10 7.10 78.7 180.3 3 3 104 52.3 31.6 15.2 10.4 7.3 16.1 19.80 (127.74) 24 K, R 5479
3.10 9.10 78.7 231.1 1 1 1500 750 454 218 233 52.7 25.60 (165.16) 26 K, R 5480
3.10 12.10 78.7 307.3 1 1 445 222 135 63.9 44.3 31.1 69.0 15.5 33.90 (218.71) 24 K, R 5481
3.25 3.25 82.6 82.6 7 7 172 86.1 52.1 25.1 17.1 12.1 26.7 6.0 9.80 (63.23) 26 K, R 5482
3.50 7.35 88.9 186.7 1 1 252 126 76.3 36.7 25.1 17.6 39.1 8.8 23.30 (150.32) 24 K, R 5483
3.63 16.27 92.2 413.3 1 1 795 398 212 106 70.5 52.9 27.7 56.00 (361.29) 24 R 5484
3.75 4.75 95.3 120.7 6 6 72.5 36.3 21.9 10.5 7.2 5.1 11.2 15.60 (100.64) 26 K, R 5485
3.80 8.60 96.5 218.4 1 1 243 121 73.6 35.4 24.2 16.9 37.7 8.4 29.80 (192.26) 24 K, R 5486
4.00 4.00 101.6 101.6 1 1 330 165 92.4 42.9 51.2 11.5 15.20 (98.06) 30 K, R 5178
30
IntroductionD
esignG
uidePolyim
ideH
eatersSiliconeRub
ber
Heaters (foil)
StandardPolyim
ide&
Rubb
er
Rubb
erH
eaters(w
ire-wound)
Mica H
eatersTherm
al-Clear
Heaters
All-Polyim
ideH
eatersSensors,
Controllers &
Accessories
Reference
S a l e s a n d S u p p o r tAmericas: 763.571.3121 | Europe: (33) 5 61 03 24 01 | Asia Pacific: (65) 6511 3388|
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5 , whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number4.00 4.00 101.6 101.6 1 1 46.5 23.3 14.3 6.1 4.9 7.2 13.94 (89.94) 24 K, R 5489
4.00 5.00 101.6 127.0 1 1 57.9 27.7 17.7 7.6 5.5 3.8 9.0 17.74 (114.45) 24 K, R 5490
4.00 5.00 101.6 127.0 7 7 48.5 25.9 16.8 7.3 5.1 3.5 7.5 17.74 (114.45) 24 K, R 5508
4.00 6.00 101.6 152.4 1 1 69.3 33.2 21.3 9.4 6.4 4.6 10.7 21.54 (138.97) 24 K, R 5491
4.00 7.00 101.6 177.8 1 1 80.7 38.6 24.7 10.9 7.2 5.3 12.5 25.34 (163.48) 24 K, R 5492
4.00 8.00 101.6 203.2 1 1 318 178 82.7 63.7 50.4 96.0 21.6 30.84 (198.97) 24 K, R 5179
4.00 8.00 101.6 203.2 1 1 92.3 43.9 28.3 12.3 8.4 6.1 14.3 29.14 (188.00) 24 K, R 5493
4.00 8.00 101.6 203.2 3 3 378 189 114 55.1 37.6 26.3 58.6 13.1 30.30 (195.48) 24 K, R 5494
4.00 9.00 101.6 228.6 1 1 103 49.5 31.7 13.4 9.3 6.8 16.0 32.94 (212.52) 24 K, R 5495
4.00 10.00 101.6 254.0 1 1 114 55.1 35.3 14.8 10.8 7.6 17.7 36.74 (237.03) 24 K, R 5496
4.00 11.00 101.6 279.4 1 1 126 60.6 38.8 16.2 11.7 8.3 19.5 40.54 (261.55) 24 K, R 5497
4.00 12.00 101.6 304.8 1 1 212 118 55.1 42.4 33.6 64.0 14.3 46.48 (299.87) 24 K, R 5180
4.00 12.00 101.6 304.8 1 1 137 66.1 42.1 17.6 12.2 9.1 21.2 44.34 (286.06) 24 K, R 5498
4.00 15.50 101.6 393.7 2 2 445 223 135 64.8 44.3 31.1 69.0 15.4 58.70 (378.71) 24 K, R 5499
4.00 16.80 101.6 426.7 6 6 720 360 218 105 71.6 50.1 25.0 63.00 (406.45) 24 R 5500
4.00 20.00 101.6 508.0 1 1 851 426 257 120 84.6 59.3 29.6 74.50 (480.64) 24 R 5501
4.05 8.05 102.9 204.5 1 1 617 312 186 89.9 61.4 43.1 95.6 21.5 30.40 (196.13) 26 K, R 5502
4.05 9.05 102.9 229.9 1 1 1400 700 420 210 139 97.1 217 49.0 34.10 (220.00) 26 K, R 5503
4.05 11.90 102.9 302.3 8 8 290 145 87.8 42.2 28.9 20.2 45.0 10.1 45.00 (290.32) 24 K, R 5504
4.50 19.40 114.3 492.8 1 1 30.1 15.1 9.1 4.3 81.30 (524.52) 24 R 5505
5.00 5.00 127.0 127.0 1 1 407 227 106 81.5 64.5 123 27.7 24.02 (154.97) 24 K, R 5181
5.00 5.00 127.0 127.0 1 1 61.5 32.6 21.1 8.9 6.1 4.3 9.5 22.54 (145.42) 24 K, R 5509
5.00 6.00 127.0 152.4 1 1 72.4 38.8 24.9 10.6 7.3 5.1 11.2 27.34 (176.39) 24 K, R 5510
5.00 7.00 127.0 177.8 1 1 84.3 45.1 29.2 12.3 8.9 5.9 13.1 32.14 (207.35) 24 K, R 5511
5.00 8.00 127.0 203.2 1 1 96.2 51.4 32.9 14.1 9.7 6.8 14.9 36.94 (238.32) 24 K, R 5512
5.00 9.00 127.0 228.6 1 1 108 57.8 36.9 15.6 10.7 7.6 16.7 41.74 (269.29) 24 K, R 5513
5.00 10.00 127.0 254.0 1 1 85.7 66.1 52.9 105 23.5 48.57 (313.35) 24 K, R 5182
5.00 10.00 127.0 254.0 1 1 119 64.2 41.5 18.6 11.9 8.5 18.4 46.54 (300.26) 24 K, R 5514
5.00 11.00 127.0 279.4 1 1 131 70.5 44.9 19.2 12.8 9.4 20.3 51.34 (331.23) 24 K, R 5515
5.00 12.00 127.0 304.8 1 1 142 76.7 48.7 20.4 13.7 10.2 22.0 56.14 (362.19) 24 K, R 5516
5.00 12.10 127.0 307.3 1 1 377 190 114 54.8 37.5 26.3 58.4 13.1 56.40 (363.87) 24 K, R 5517
5.00 15.00 127.0 381.0 1 1 57.2 44.1 35.3 69.8 15.6 73.12 (471.74) 24 K, R 5183
5.00 15.97 127.0 405.6 8 8 271 136 72.2 36.1 24.1 18.1 42.0 9.4 76.00 (490.32) 24 K, R 5518
5.05 5.05 128.3 128.3 3 3 227 113 68.6 32.3 22.6 15.8 35.2 7.9 23.60 (152.26) 24 K, R 5519
5.05 5.05 128.3 128.3 3 3 262 131 79.4 38.2 26.1 18.3 40.6 9.1 23.60 (152.26) 24 K, R 5520
5.05 8.05 128.3 204.5 1 1 953 476 288 138 94.8 66.4 148 33.2 38.30 (247.10) 26 K, R 5521
5.05 10.10 128.3 256.5 1 1 660 330 205 98.2 65.7 46.1 102 23.0 48.00 (309.68) 26 K, R 5522
5.05 10.50 128.3 266.7 6 6 784 392 237 114 78.1 55.2 122 27.3 50.00 (322.58) 26 K, R 5523
5.10 12.10 129.5 307.3 1 1 523 261 158 76.2 52.1 36.4 81.1 18.2 58.00 (374.19) 26 K, R 5524
5.50 5.50 139.7 139.7 1 1 50.0 25.7 14.2 6.4 4.6 3.4 7.8 29.17 (188.19) 26 K, R 5596
5.50 7.00 139.7 177.8 1 1 384 192 116 55.8 38.1 26.7 59.5 13.3 35.80 (230.97) 24 K, R 5525
6.00 6.00 152.4 152.4 1 1 174 87.0 48.7 22.6 17.4 12.2 27.0 6.0 34.38 (221.81) 24 K, R 5560
6.06 8.06 153.9 204.7 6 6 362 182 109 52.6 36.1 25.2 56.1 12.6 45.70 (294.84) 24 K, R 5526
6.06 8.06 153.9 204.7 2 2 630 315 190 91.5 62.6 43.8 97.7 21.9 46.10 (297.42) 26 K, R 5527
6.90 9.00 175.3 228.6 2 2 88.1 44.1 26.1 12.8 8.8 6.2 13.7 58.30 (376.13) 24 K, R 5528
7.50 11.55 190.5 293.4 8 8 2890 1446 874 420 448 101 74.00 (477.42) 26 K, R 5529
31
Intr
oduc
tion
Des
ign
Gui
dePo
lyim
ide
Hea
ters
Silic
one
Rub
ber
Hea
ters
(foi
l)
Stan
dard
Poly
imid
e&
Rub
ber
Rub
ber
Hea
ters
(wire
-wou
nd)
Mic
a H
eate
rsTh
erm
al-C
lear
Hea
ters
All-
Poly
imid
eH
eate
rsSe
nsor
s,C
ontr
olle
rs &
Acc
esso
ries
Refe
renc
e
| Flexible Heaters Design Guide | www.minco.com
Standard Polyimide and Rubber Heaters
*Resistance tolerance is ±10% or ±0.5 , whichever is greaterRubber (HR) models not available with NiFe element
Size (in) Size (mm) Type Resistance options- ohms* Effective area Lead Insu- ModelX Y X Y R(0°C) [May be used with Heaterstat] → NiFe Ni in² (cm²) AWG lation number7.90 18.30 200.7 464.8 8 8 241 120 73.1 35.1 24.1 16.8 8.3 140.00 (903.22) 24 R 5530
8.80 11.20 223.5 284.5 8 8 220 110 66.5 31.9 21.8 15.3 34.1 7.6 94.40 (609.03) 24 K, R 5531
9.00 12.00 228.6 304.8 3 3 545 273 165 79.3 54.2 38.1 84.5 18.9 103.00 (664.51) 24 K, R 5532
9.00 18.00 228.6 457.2 6 6 184 92.1 55.6 26.7 18.3 12.8 6.4 156.00 (1006.45) 24 R 5533
10.00 10.00 254.0 254.0 1 1 42.8 33.1 26.4 52.2 11.7 97.52 (629.16) 20 K, R 5184
10.00 15.00 254.0 381.0 1 1 28.6 22.0 17.6 34.9 7.8 146.92 (947.87) 20 K, R 5185
10.00 18.00 254.0 457.2 1 1 161 80.4 48.6 23.4 16.1 11.2 5.6 173.00 (1116.13) 24 R 5534
10.07 18.27 255.8 464.1 7 7 327 163 98.9 47.5 32.5 22.7 11.3 177.00 (1141.93) 24 R 5535
10.70 11.00 271.8 279.4 6 6 807 403 244 117 80.3 56.1 125 28.0 114.00 (735.48) 24 K, R 5536
11.00 15.00 279.4 381.0 1 1 200 103 56.6 25.5 18.5 13.6 31.0 6.9 158.56 (1022.97) 20 K, R 5600
0.50 0.09 12.7 2.4 31 K 25.0 12.8 7.1 0.13 (0.84) 30 K 5186
0.50 12.7 10 0 26.1 13.1 7.8 3.8 0.15 (0.97) 30 K 5537
0.75 0.12 19.1 3.1 31 K 39.2 20.6 11.2 5.2 3.9 3.0 6.1 0.35 (2.26) 26 K, R 5593
0.78 19.8 10 0 32.2 16.1 9.7 4.7 0.32 (2.06) 30 K, R 5538
0.78 19.8 10 0 70.1 35.2 21.1 10.2 10.9 0.32 (2.06) 30 K 5539
0.98 0.12 24.9 3.0 11 = 37.2 18.6 11.3 5.4 5.8 0.65 (4.19) 24 K, R 5540
1.00 0.09 25.4 2.4 31 K 157 80.5 44.4 19.9 14.4 10.5 24.3 5.6 0.68 (4.39) 26 K 5187
1.10 0.12 27.9 3.0 11 = 61.1 30.5 18.5 8.9 9.5 0.66 (4.26) 24 K, R 5541
1.18 30.0 30 J 288 144 80.6 37.4 28.8 20.2 44.6 10.4 0.90 (5.81) 30 K 5561
1.25 0.60 31.8 15.2 11 = 84.4 42.2 25.5 12.3 13.1 0.59 (3.81) 26 K, R 5542
1.32 33.5 10 0 38.0 19.0 10.6 4.9 3.8 5.9 1.19 (7.68) 30 K, R 5562
1.35 0.45 34.3 11.4 11 = 156 78.1 47.2 22.7 24.2 5.6 0.96 (6.19) 30 K 5543
1.50 0.12 38.1 3.1 31 K 75.0 39.0 21.3 9.8 7.2 5.4 11.6 1.60 (10.32) 26 K, R 5597
1.73 43.9 10 0 227 114 68.7 33.1 35.2 8.0 2.00 (12.90) 30 K, R 5544
1.75 0.12 44.5 3.0 11 = 61.1 30.5 18.5 8.9 6.1 4.2 9.5 2.19 (14.13) 24 K, R 5545
1.85 0.12 47.0 3.0 11 = 61.2 30.6 18.5 8.9 6.1 4.2 9.5 2.44 (15.74) 26 K, R 5546
1.90 48.3 10 0 156 78.4 47.4 22.8 24.2 5.5 2.48 (16.00) 24 K, R 5547
2.00 0.12 50.8 3.1 31 K 100 51.9 28.4 13.0 9.6 7.1 15.5 2.93 (18.90) 26 K, R 5598
2.13 1.12 54.1 28.4 11 = 180 90.1 54.6 26.3 27.9 6.3 2.16 (13.94) 26 K, R 5548
2.45 62.2 10 0 530 265 160 77.1 82.2 18.8 4.16 (26.84) 26 K, R 5549
2.85 72.4 10 0 200 100 56.0 26.0 20.0 14.0 31.0 7.0 5.98 (38.58) 30 K, R 5563
3.00 0.12 76.2 3.1 31 K 378 194 107 48.0 34.7 25.4 58.6 13.3 6.61 (42.65) 26 K, R 5188
3.40 86.4 10 0 198 99.0 55.4 25.7 19.8 13.9 30.7 6.9 8.34 (53.81) 24 K, R 5564
3.72 2.09 94.5 53.1 11 = 317 158 95.9 46.1 31.6 22.1 49.1 11.1 6.76 (43.61) 26 K, R 5550
4.30 3.42 109.2 86.9 11 = 405 206 125 60.1 62.8 14.3 3.91 (25.23) 26 K, R 5551
4.75 2.50 120.7 63.5 11 = 54.5 27.3 14.5 7.2 4.8 3.6 8.4 11.48 (74.06) 24 K, R 5552
6.00 0.12 152.4 3.1 11 = 150 77.4 42.5 19.2 14.0 10.3 23.3 5.2 27.02 (174.32) 26 K, R 5599
6.25 2.00 158.8 50.8 11 = 610 305 185 88.8 60.7 42.5 94.6 21.3 25.66 (165.55) 24 K, R 5553
6.75 4.75 171.5 120.7 11 = 251 125 76.1 36.6 25.1 17.5 38.9 8.7 15.79 (101.87) 26 K, R 5554
7.06 179.3 10 0 120 60.1 31.9 16.1 10.6 7.4 18.6 37.19 (239.94) 24 K, R 5555
8.25 4.32 209.6 109.7 11 = 670 335 202 97.4 67.1 47.4 104 23.3 36.13 (233.10) 24 K, R 5556
9.00 3.00 228.6 76.2 11 = 710 355 215 101 70.6 49.4 110 24.7 52.46 (338.45) 24 K, R 5557
9.60 0.90 243.8 22.9 11 = 72.7 36.3 21.9 10.6 7.2 5.1 11.3 67.65 (436.45) 24 K, R 5558
10.00 0.25 254.0 6.4 11 = 667 334 202 96.7 67.1 47.7 103 23.2 74.78 (482.45) 24 K, R 5559
Configure Minco heaters and order online at: www.minco.com/heater_config/All standard polyimide and silicone rubber heater specifications subject to change