power connection options
TRANSCRIPT
1
+
-
ground
Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
Power Connection Options
24v Connection
ICS 3 and ICS 3S Connection
ICS 2 Connection
24 Volt lights are built with flying leads and have load limiting resistors for use with any regulated 24 volt DC power source.
Inline Current Source built into the power cable.
Requires 24v power source
24Flying/tinned leads
Powered with:24V power supply
5Flying/tinned leads
Powered with:5V power supply
ICS 3 (I3)Combination strobe/continous in-line controller
Powered with:24V power supply
ICS 3S (I3S)Default-OFFstrobe/continous in-line controller
Powered with:24V power supply
ICS 2 (IC) Continous in-line controller
Powered with:24V power supply
+-
gate -0-10V Analog
Inline Current Source built into the power cable.
Requires 24v power source
Default off for ICS3 S version
5v Connection
5 Volt lights are built with flying leads and have load limiting resistors for use with any regulated 5 volt DC power source.
+
-
trigger+ (active HIGH)
Not used
Analog Dimming
ICS 2
ICS 3 and 3S
+
-
ground
2Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
Power Connection Options
For Use With:CS100, CS100-IC, CS300, CS300-IC, CS410, CS420,MS210, MS220S4000, S6000, S6000-AS
C2 Connection
C5 Connection
C1 Connection
M12 Add On Connection
For Use With:24v, ICS 2, and ICS 3 wiring
C1 ConnectorFor use with:DCS SeriesControllers
C2 ConnectorFor use with:Legacy Controllers
(Not recommended for new applications)
C5 ConnectorFor use with:Pulsar 320 StrobeController.
For Use With:
For Use With:
3Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
Power Connection Options
ICS 2 Specifications
5 Pin
5 Pin
Dimensional Information
M12 Connector Pin-OutMale end view. Ai lights are built with the male connector standard.
PIN COLOR DESC.
DIMENSIONS IN MM
1 BROWN +24V IN2 WHITE Not used3 BLUE -24V IN4 BLACK ACTIVE HIGH5 GRAY Analog Dimming, 0-10V
ICS 2
ICS 3
4 Pin24 Volt
2
4
1
53
PIN COLOR DESC.
1 BROWN +24V IN2 WHITE 0-10V ANALOG3 BLUE -24V IN4 BLACK GATE ACTIVE LOW5 GRAY Not Connected
2
4
1
53
PIN COLOR DESC.
1 BROWN +24V IN2 WHITE 0-10V ANALOG3 BLUE -24V IN4 BLACK GATE ACTIVE LOW5 GRAY Not Connected
2
4
1
53
0.471 0.810
0.390
2.362
Connection Diagram
4
Power Connection OptionsICS 2 Wiring Diagrams
Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE LOW GATE
GND
NPN
GND
4.7K
TRIGGER
LOW TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE HIGH GATE
GND
PNP
GND
4.7K
TRIGGER
HIGH TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
0-10V ANALOG CONTROL
GND
GND
0-10V ADJUST.
LINEAR OUTPUT ADJUST WITH EXTERNAL POTENTIOMETER
5K
0-10V ANALOG CONTROLLINEAR OUTPUT ADJUST
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
GND
0-10V ADJUST.
STANDARD OPERATIONLIGHT IS ALWAYS ON
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE LOW GATE
GND
NPN
GND
4.7K
TRIGGER
LOW TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE HIGH GATE
GND
PNP
GND
4.7K
TRIGGER
HIGH TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
0-10V ANALOG CONTROL
GND
GND
0-10V ADJUST.
LINEAR OUTPUT ADJUST WITH EXTERNAL POTENTIOMETER
5K
0-10V ANALOG CONTROLLINEAR OUTPUT ADJUST
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
GND
0-10V ADJUST.
STANDARD OPERATIONLIGHT IS ALWAYS ON
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE LOW GATE
GND
NPN
GND
4.7K
TRIGGER
LOW TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE HIGH GATE
GND
PNP
GND
4.7K
TRIGGER
HIGH TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
0-10V ANALOG CONTROL
GND
GND
0-10V ADJUST.
LINEAR OUTPUT ADJUST WITH EXTERNAL POTENTIOMETER
5K
0-10V ANALOG CONTROLLINEAR OUTPUT ADJUST
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
GND
0-10V ADJUST.
STANDARD OPERATIONLIGHT IS ALWAYS ON
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE LOW GATE
GND
NPN
GND
4.7K
TRIGGER
LOW TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE HIGH GATE
GND
PNP
GND
4.7K
TRIGGER
HIGH TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
0-10V ANALOG CONTROL
GND
GND
0-10V ADJUST.
LINEAR OUTPUT ADJUST WITH EXTERNAL POTENTIOMETER
5K
0-10V ANALOG CONTROLLINEAR OUTPUT ADJUST
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
GND
0-10V ADJUST.
STANDARD OPERATIONLIGHT IS ALWAYS ON
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE LOW GATE
GND
NPN
GND
4.7K
TRIGGER
LOW TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
ACTIVE HIGH GATE
GND
PNP
GND
4.7K
TRIGGER
HIGH TRIGGER SHUTS LIGHT OFF
BROWN
BLUE
+24VDC
WHITE
BLACK
0-10V ANALOG CONTROL
GND
GND
0-10V ADJUST.
LINEAR OUTPUT ADJUST WITH EXTERNAL POTENTIOMETER
5K
0-10V ANALOG CONTROLLINEAR OUTPUT ADJUST
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
GND
0-10V ADJUST.
STANDARD OPERATIONLIGHT IS ALWAYS ON
BROWN
BLUE
+24VDC
WHITE
BLACK
GND
5
Power Connection Options
ICS 2 Wiring Diagram for Optional Manual Intensity Control
Note: The MP-iCS is compatible only with lights built with the IC wiring option after 3/1/2012. It cannot be used with 24v lights, or the iCS 1.0
ICS 3/3S Specifications
Parameter Specification Notes
Strobe output
Current Output Adj.
Max. Input Current
Trigger
Input Voltage Range
Active HI: BLACK
Mechanical & Environmental
Storage Temperature
Operating Temperature
Housing Material
Weight
Size
+18 to 30 VDC
0 - 12A* * Pulse-width/Light head dependent
Min to Max Current adj. as established by factory setting
Maximum current set assuming 300µSec operation
1.1A
Active HI: BLACK
-40 to +125C
0 to +70C
High Impact Polycarbonate
Approx 1.7 oz
Approx 4.55L x 0.67W x 0.70H
Approx 100mA local
TTL compatible, 30VDC tolerant
Cable Not Included
Inches
24V nominal
Mode Select Bypass triggering mode
Max. Repetition Rate 100 Hz ** ** Light head dependent
BROWN
BLUE
WHITE
BLACK
GRAY
VIN +
VIN -
Not used
Active HIGH trigger input
ICS PINOUT
Analog dimming, 0-10V
Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
MP-ICS Manual Dimming Control Wiring Diagram for ICS 2All connections are made at the input
6
Power Connection OptionsICS 3/3S Wiring Diagrams
Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
+24V BROWN (PIN 1)GND BLUE (PIN 3)ANALOG GRAY (PIN 5)
i3
TYPICAL CONNECTION - CONTINUOUS USE
Light is on continuous when power is applied.Analog control is optional for remote dimming (0-10VDC)
+24V BROWN (PIN 1)GND BLUE (PIN 3)TRIGGER+ BLACK (PIN 4)
i3
TYPICAL CONNECTION - STROBE MODE
Light is on continuous when power is applied. The first trigger pulse will initiate STROBE MODE. The controller remains in STROBE MODE until the power is toggled.
Output light pulse width always follows the duration of the input trigger width.
A period of overdrive occurs within 5msec from the beginning of the pulse. After this period of time, the on-time of the pulse is at the continuous output level.
ANALOG GRAY (PIN 5)
WIRING INFORMATION 5-30VDC
i3 / BLACK / PIN 4
i3 / BLUE / PIN 3
*
*External resistors may not be neededCheck documentation on I/O for recommendations and voltage limits
OFF
ON
GNDI/O
PNP / SOURCING
5-30VDC
i3 / BLACK / PIN 4
i3 / BLUE / PIN 3
*
*External resistors may not be neededCheck documentation on I/O for recommendations and voltage limits
OFF
ON
GNDI/O
NPN / SINKING
The i3 does not have a true sinking input.The emitter must be tied to the trigger as shown
i3 / GRAY / PIN 5
i3 / BLUE / PIN 3
GND
Analog Dimming: 0 = 10%, 10 = 100% outputAnalog dimming works in both strobe and continuous
1-10VDC
WIRING DIAGRAMS
ADAPTIVE OVERDRIVE™ DIAGRAM
7
Power Connection OptionsICS 3/3S Wiring Diagrams
Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
+24V BROWN (PIN 1)GND BLUE (PIN 3)ANALOG GRAY (PIN 5)
i3
TYPICAL CONNECTION - CONTINUOUS USE
Light is on continuous when power is applied.Analog control is optional for remote dimming (0-10VDC)
+24V BROWN (PIN 1)GND BLUE (PIN 3)TRIGGER+ BLACK (PIN 4)
i3
TYPICAL CONNECTION - STROBE MODE
Light is on continuous when power is applied. The first trigger pulse will initiate STROBE MODE. The controller remains in STROBE MODE until the power is toggled.
Output light pulse width always follows the duration of the input trigger width.
A period of overdrive occurs within 5msec from the beginning of the pulse. After this period of time, the on-time of the pulse is at the continuous output level.
ANALOG GRAY (PIN 5)
WIRING INFORMATION 5-30VDC
i3 / BLACK / PIN 4
i3 / BLUE / PIN 3
*
*External resistors may not be neededCheck documentation on I/O for recommendations and voltage limits
OFF
ON
GNDI/O
PNP / SOURCING
5-30VDC
i3 / BLACK / PIN 4
i3 / BLUE / PIN 3
*
*External resistors may not be neededCheck documentation on I/O for recommendations and voltage limits
OFF
ON
GNDI/O
NPN / SINKING
The i3 does not have a true sinking input.The emitter must be tied to the trigger as shown
i3 / GRAY / PIN 5
i3 / BLUE / PIN 3
GND
Analog Dimming: 0 = 10%, 10 = 100% outputAnalog dimming works in both strobe and continuous
1-10VDC
WIRING DIAGRAMS
ADAPTIVE OVERDRIVE™ DIAGRAM
8
Power Connection Options
M12 Connector Pin-Out
5 Pin
5 Pin
Dimensional Information
M12 Connector Pin-OutMale end view. Ai lights are built with the male connector standard.
PIN COLOR DESC.
DIMENSIONS IN MM
1 BROWN +24V IN2 WHITE Not used3 BLUE -24V IN4 BLACK ACTIVE HIGH5 GRAY Analog Dimming, 0-10V
ICS 2
ICS 3
4 Pin24 Volt
2
4
1
53
PIN COLOR DESC.
1 BROWN +24V IN2 WHITE 0-10V ANALOG3 BLUE -24V IN4 BLACK GATE ACTIVE LOW5 GRAY Not Connected
2
4
1
53
PIN COLOR DESC.
1 BROWN +24V IN2 WHITE 0-10V ANALOG3 BLUE -24V IN4 BLACK GATE ACTIVE LOW5 GRAY Not Connected
2
4
1
53
0.471 0.810
0.390
2.362
Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016
9
Power Connection Options
This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility
(EMC) as stated in the product specifications. These requirements and limits are designed to provide reasonable
protection against harmful interference only when the product is operated in its intended industrial electromagnetic
environment. To minimize the potential for electromagnetic interference or unacceptable performance degradation,
install and use this product in strict accordance with the instructions in the product documentation.
Every Advanced illumination, Inc. (Ai) product is thoroughly inspected and tested before leaving the factory.
Products are warranted to be free of defects in workmanship and materials for a period of two years from the
original date of purchase. Should a defect develop during this period, please contact Ai Customer Service or your
Ai distributor for a Return Merchandise Authorization (RMA), and return the complete product, freight prepaid, to Ai.
If a defect is found, Ai will - at our discretion - repair or replace the product without charge. Ai claims no liability for
any implied warranties, including “merchantability” and “fitness for a specific purpose.”
For information on existing orders, or to make an order adjustment, contact us Monday through Friday 8:00 am to
5:00 pm, EST or send an email to [email protected].
Warranty Information
Electromagnetic Compatibility
Customer Service
Company Information
Advanced Illumination
Email: [email protected] Web: advancedillumination.com © 2015 Advanced Illumination Inc. All rights reserved
440 State Garage Road, Rochester VT. 05767
Phone: 802.767.3830
Fax: 802.767.3831
Updated 9/19/2016Updated 10/11/2017 (DCN 2560)
Released 1/22/2016