power system stabilizers presentation
DESCRIPTION
Presentation of PSS models with Emphsis on PSS4BTRANSCRIPT
Power System Stabilizer Models with Emphasis on PSS4B
Mohammad Umar Rehman
Research Scholar, EED
IIT Delhi
15th March 2013
2
Outline Review Various PSS Models Comparison of PSS2B and PSS4B Alternative types
3
Review Power System Stabilizers are an essential
component of modern interconnected systems Provides damping of power system oscillations
through excitation control leading to enhancement of transient stability and transmission capacity
Needs to produce a torque component in phase with rotor speed deviations (Δω)
Consists of a lead-lag compensator as the basic functioning block
Common input signals are shaft speed, terminal frequency, and power or their combination
4
5
6
Evolution of PSS Models
7
PSS1A, Single input PSS
Transducer Washout
Lead Lag compensators
Account for LF signals and Characteristics shaping
8
PSS2B, Dual-input PSS
9
PSS2B…contd When using speed as an input signal, torsional
oscillations may occur creating disturbance in measurement
The solution lies in using several sensors &/or a torsional filter
Therefore, the Integral of accelerating power-based stabilizer or PSS2B was developed to overcome this
10
PSS2B…contd Represents two distinct types of dual-input stabilizer
implementations:
a) Stabilizers that, in the frequency range of system oscillations, act as electrical power input stabilizers. These use the speed or frequency input for the generation of an equivalent mechanical power signal, to make the total signal insensitive to mechanical power change
b) Stabilizers that use a combination of speed (or frequency) and electrical power. These systems usually use the speed directly (i.e., without phase-lead compensation) and add a signal proportional to electrical power to achieve the desired stabilizing signal shaping.
11
PSS3B, Dual-input PSS
PE
Δω
Transducer Washout
Phase compensation
12
PSS4B
13
PSS4B
14
PSS4B…contd Also known as multi-band stabilizer Motivation: lead/lag compensating filters in the older
structures could not give an accurate compensation over a wide range of oscillation frequencies
If the network suffers from low and high frequency oscillations, the tuning procedure of the single-band stabilizers have to compromise and will not achieve optimal damping in any of the oscillations
The multi-band stabilizer has three separate signal bands, which can be tuned individually to handle different oscillation frequencies
15
PSS4B…contd The low band is typically associated with the power
system global mode, the intermediate with the inter-area modes, and the high with the local modes
The PSS4B measures the rotor speed deviation in two different ways. Δω L-I feeds the low and intermediate bands, while ΔωH is dedicated to the high-frequency band.
Next we consider performance evaluation of PSS2B and PSS4B
16
SMIB Scenario Gain margins and phase margins were evaluated for
the following benchmark system [5]
The stabilizers have a robust performance satisfy the conventional criteria of a minimum of 6 dB and 30° for gain and phase margins, respectively
17
18
Multi-machine scenario Damping performance was evaluated for the well
known Kundur Test system [6]
PSS4B outperforms PSS2B by providing better damping under all oscillatory modes
19
20
Pros & Cons of PSS2B
21
Pros & Cons of PSS4B
22
Alternative Types of PSS
1. Based on shaft speed signal (Δω) Earliest PSS (1960s) to be used with hydraulic units Measurement is prone to noise and can lead to
inaccuracies Needs several measurement points and a torsional
filter thus adding to complexity and cost
2. Combination of shaft speed and power (Δ-P-ω) Based on the equation
23
…contd The integral of mech power is related to shaft
speed and elec power as:
The overall TF is:
24
…contd Major advantages:
1. The ΔPe signal a high degree of attenuation towards torsional oscillations eliminating the need for a torsional filter
2. Measurement becomes simple with the use of end of shaft speed sensing arrangement and also allows used of standard design for all units irrespective of torsional charactersitics
25
References[1] Kamwa, I. et. al. “ IEEE PSS2B Versus PSS4B: The Limits of
Performance of Modern Power System Stabilizers”, IEEE Transactions on Power Systems, vol. 20, no. 2, May 2005.
[2] IEEE, IEEE Recommended Practice for Excitation System Models for Power System Stability Studies, IEEE Std 421.5™-2005.
[3] Hammer, A., “Analysis of IEEE Power System Stabilizer Models”, M. S. Thesis, Department of Electric Power Engineering, Norwegian University of Science and Technology, 2011.
[4] Guanghui, Hua, “Research and Implementation on Power System Stabilizer PSS4B Model”, China International Conference on Electricity Distribution, 2010.
[5] G. N. Taranto, J. H. Chow, and H. A. Othman, “Robust redesign of power system damping controllers,” IEEE Trans. Contr. Syst. Technol., vol. 3, no. 3, pp. 290–298, Sep. 1995.
[6] Prabha Kundur, “Power System Stability and Control”, McGraw Hill, 1994.