PRE AMPLIFIER

2 IPP-8213

Contents 2

Welcome 3

Unpacking 3

Before Use 3

Safety Instruction 4

Operation 5

Features 5

Front Panel 6

Rear Panel 7

RACK Connection 8

Block Diagram 9

Specification 10

Service and Warranty 11

Contents

PRE AMPLIFIER

IPP-8213 3

Welcome you from management and staffs of INKEL PA.All of the staffs here at INKEL PA have dedicated to provide excellent products of value, and we are gladthat you have purchased one of our products.We sincerely trust that this product will provide satisfactory service, but if anything goes up you do not satisfy completely, we will endeavor to make things right.Welcome to INKEL PA and thank you for joining our worldwide family.

Please inspect all equipment carefully right after unpacking. If you find any damages, contact your supplieror dealer immediately. Only a shipper may file a damage claim as a carrier for damages which have been incurred during shipping. Be sure to keep carton boxes and other all packing materials for the carrier’sinspection. If your packing materials are in good condition, please keep them. If you ever need to returnthe unit to INKEL PA or an authorized service center, you should use only the original factory packing.

Welcome

WARNING : TO PREVENT FIRE OF ELECTRIC SHOCK HAZARD,DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE

Unpacking

To insure proper use of this product, please read owner’s manual carefully and keep this manual in an easily accessible place for future reference.

Before Use

CAUTION : TO REDUCE THE RISKOF ELECTRIC SHOCK

DO NOT REMOVE THE COVER (OR BACK)NO USER SERVICABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This lightening flash with arrowhead symbol within an equilateral triangle is intended to alert theuser to the presence of non insulated “dangerous” voltage within the product’s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to persons.

This exclamation point within an equilateral triangle is intended to alert the user to the presenceof important operating and maintenance (servicing) instruction in the literature accompanying theproducts.

PRE AMPLIFIER

4 IPP-8213

Safety Instruction

1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the thirdprong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician forreplacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and thepoint where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into theapparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying documents mean that used electricaland electronic products and batteries should not be mixed with general household waste. For propertreatment, recovery and recycling of old products and used batteries, please take them toapplicable collection points, in accordance with your national legislation.By disposing of these products and batteries correctly, you will help to save valuable resources andprevent any potential negative effects on human health and the environment which could otherwise arisefrom inappropriate waste handling.For more information about collection and recycling of old products and batteries, please contact yourlocal municipality, your waste diposal service or the point of sale where you purchased the items.

Information on Disposal in other Countries outside the European UnionThese symbols are only valid in the European Union. If you wish to discard these items, please contactyour local authorities or dealer and ask for the correct method of diposal.

Note for the battery symbol (bottom two symbol examples):The sign Pb below the symbol for batteries indicates that this batteries contains lead.

PRE AMPLIFIER

IPP-8213 5

Features

* 9 MIC/LINE IN, 1 MASTER OUT, 2 AUX OUT, and 1 REC OUTBuilt-in nine microphone, one master out, two sub out for convenient using of this unit and one recording out which isnot influenced by output volume controller.

* 2 AUX IN & 2 PRIORITY INPUTAuxiliary input is built-in so that users can use external sound sources conveniently and the sound source connectedto 2 channels of this priority input is played prior to the other input.

* INDIVIDUAL EQUALIZER PER CHANNEL3-band graphic equalizer controls on each input channel.

* 4-BAND MASTER EQUALIZER4-band graphic equalizer controls on master output.

* PHANTOM POWER FOR CONDENSOR MICROPHONEDesigned to use condenser MIC on channel 1 and 2 and supply voltage is DC +18V.

* DUCKINGDucking function available on channel 1 and 2 enable their sound sources to be broadcasted prior to the others.

Operation

1. Plug in or connect DC terminal to power distributor(IPD-8329) with proper polarity (AC INPUT, DC24V).2. Place all slide volume on the front panel and TRIM volume on minimized. 3. If turn on the power, this unit starts operation.4. When connect CD, deck, or MIC on input, adjust gain input with TRIM volume as signal level of desired channel.5. Adjust input channel volume control for favorable audio mixing and adjust output level with output channel volume

control.6. Adjust EQ volume of each channel with monitoring outputs.

PRE AMPLIFIER

6 IPP-8213

1. TRIM CONTROLThis volume controls gain of incoming signaland its adjustable range is 44dB.

2. SIGNAL INDICATORThis LED indicates that signal has been inputproperly on related channel.

3. PEAK INDICATOR (INPUT CHANNEL)This LED indicates that incoming signal hasbeen overloaded, and it is illuminated before3dB to be clipping.

4. INPUT LEVEL CONTROL (CHANNELFADER)It controls level of input signal per channel.Faders of unused channels should be set totheir lowest points.

5. AUX INPUT CONTROL (AUX1, AUX2)It controls amount of signal which is incomingthrough auxiliary input jack.

6. PEAK INDICATOR (OUTPUT SECTION)If mixed level or master output level per channelis too high, this LED is illuminated before 3dB tobe clipping.

7. MASTER CONTROL (MASTER FADER)This is the master control to adjust mixed signalfrom each input channel.

8. 3-BAND EQUALIZER (INPUT CHANNEL)It has been designed as 3-band equalizer toadjust input signal to much richer sound.(HIGH: 10kHz, MID: 1kHz, LOW: 100Hz)

9. PRIORITY INPUT CONTROL (PRIORITY 1,PRIORITY 2)This controller releases prior input signal thanother input channels.Priority of this unit.- First : PRIORITY 1, or PRIORITY 2 INPUT- Second : CHANNEL 1/2 which ducking

switched on.- Third : inputs of other channels (CH 3~9), AUX

input.

10. 4-BAND EQUALIZER (MASTER SECTION)It has been designed as 4-band equalizer toadjust input signal to much richer sound.(HIGH : 10kHz, MID-HI : 2kHz, MID-LOW :400Hz, LOW : 80Hz)

11. SUB OUT 1, 2 CONTROLThis is sub output control to adjust mixed signalfrom each input channel.

12. POWER SWITCHIf press this switch, then power is supplied andLED is illuminated.

13. PHANTOM POWER INDICATORThis LED indicates phantom supply statue (DC+18V) for condenser MIC.

Front Panel

PRE AMPLIFIER

IPP-8213 7

Rear Panel

1. MASTER OUT JACKThis is a balanced XLR output jack for connecting to theinput of power amplifier, its output level is +4dBm/ 600Ω.

2. SUB OUT JACKThese are unbalanced 1/4" PL55 jack for connecting tothe input of power amplifier or other audio inputs, itsoutput level is +4dBm/ 600Ω.

3. PRIORITY INPUT JACKThis input jack is used to output the signal first than otherinputs. If signal is input through this jack, all channels areblocked automatically.

4. AUX INPUT JACKWith this jack, auxiliary equipment can be connected. Itsinput level is -10dBm/20kΩ.

5. MIC INPUT JACKIt connects XLR type of MIC (1:GND, 2:HOT, 3:COLD). Its impedance is 50~600Ω.MIC input connector of CH1 and CH2 is supplied +18Vpower through No.2 and No.3 pins by PHANTOM POWERswitch.

6. AC INPUT & FUSE HOLDERConnect the supplied standard AC input cable to thisunit.The fuse holder below the input contains the ACoverload protection fuse.If the fuse has blown out, replace it with a fuse of sametype and rating.If the fuse continues to blow, refer servicing to qualifiedservice technician.

7. REC OUT JACKAs UNBALANCE output to record mixed signal, its outputlevel is -10dBV/10kΩ.

8. INSERT JACKThis is an unbalanced line-level input.Inserting a connector into the insert jack will disconnectthe output of mixer’s master output buss.

9. DC INPUT & OUTPUT TERMINALThese connectors can be used when battery should usecause of AC power failure, and its DC power is 24V. Youcan use it by connecting with IPD-8329.

10. STEREO LINE INPUT JACKThese jack connect stereo equipment of line level such asCD, tuner, and cassette deck.

11. MONO LINE INPUT JACKThese jack connect mono equipment of line level such asCD, tuner, and cassette deck.

12. DUCKING SWITCHWhen the ducking switches are activated,signal to theassociated MIC inputs 1 and 2 will automatically lower thegain level of the input channels.

13. PHANTOM POWER SWITCHWhen you want to use condenser MIC, if turn on thisswitch, +18V condenser MIC power is supplied on No.2and 3 of XLR jack. Because this power is supplied tomicrophones in parallel, you can connect it to otherdynamic microphones. However, if connect it to othertypes of MIC, be sure about plug wiring to do notunbalanced.

* Note: If turn on this switch when volume controller of inputchannel and mater volume controller is not placedat minimized, impact voltage can be incurredsuddenly to MIC circuit, and it may cause defeats ofspeaker.

PRE AMPLIFIER

8 IPP-8213

RACK Connection

Source input(Aux&Mic)

MicrophoneLine Input

Source Input(CD, Deck, Tuner)

Connection Line

Signal Line

PRE AMPLIFIER

IPP-8213 9

Block Diagram

PRE AMPLIFIER

10 IPP-8213

Specifications

■■ ELECTRICAL

Rated Output

Master Output +4dBm/600Ω, BALANCED

Sub 1, 2 Output +4dBm/600Ω, UNBALANCED

Rec Output -10dBV/10kΩ, UNBALANCED

Input Sensitivity / Impedance

Mic (CH1~CH9) -60dBm/600Ω, BALANCED

Line (CH1~CH6) -20dBm/47kΩ, BALANCED

Line (CH7~CH9) -20dBm/47kΩ, UNBALANCED

Aux 1, 2 -10dBm/20kΩ, UNBALANCED

Priority 1, 2 0dBm/20kΩ, UNBALANCED

Insert 0dBV/20kΩ, UNBALANCED

T.H.D Less than 0.5%

Frequency Response

Input Channel

High (10kHz) ±12dB

Mid (1kHz) ±12dB

Low (100Hz) ±12dB

Output Channel

High (10kHz) ±12dB

Hi-Mid (2kHz) ±12dB

Low-Mid (400Hz) ±12dB

Low (80Hz) ±12dB

Residual Noise Less than -90dB

In/Out Crosstalk Less than -90dB

Phantom Power +18V DC

Operation Temperature -10℃ ~ +40℃

Storage Temperature -20℃ ~ +60℃

■ GENERAL

Power Source AC 100V - 120V, 220V- 240V, 50/ 60Hz, DC 24V

Power Consumption 10W

Weight 7.5kg

Dimension 482(W)×88(H)×280(D)mm

※ Specifications and design are subject to change without notice.

PRE AMPLIFIER

IPP-8213 11

Service and Warranty

TO PURCHASE ADDITIONAL INKEL PA. GEAR AND ACCESSORIESTo purchase INKEL PA gear and optional accessories, contact any authorized INKEL PA distributor.

For a list of INKEL PA distributors please visit our website at www.inkelpa.com.

SERVICE AND REPAIRFor replacement parts, service and repairs please contact the INKEL PA distributor in your country.

INKEL PA does not release service manuals to consumers, and advice users to not attempt any self repairs, as doing so

voids all warranties.

You can locate a dealer near you at www.inkelpa.com.

WARRANTY INFORMATIONWarranty terms and conditions vary by country and may not be the same for all products.

Terms and conditions of warranty for a given product may be determined first by locating the appropriate country which

the product was purchased in, then by locating the product type.

To obtain specific warranty information and available service locations contact INKEL PA directly or the authorized

INKEL PA distributor for your specific country or region.

CUSTOMER SERVICE AND TECHNICAL SUPPORTWe encourage you to visit our online help and support at http://www.inkelpa.com.

There you can find answers to frequently asked questions, tech tips, downloads, returns instruction and other helpful

information.

We make every effort to answer your questions within one business day.