private and confidential tracetek iserver concepts, set-up, operation
TRANSCRIPT
Private and Confidential
TraceTek iServer
Concepts, Set-up, Operation
Private and Confidential
The Concept
The SIMs monitor any TraceTek cable or probe sensor just like they would in any other application.
The iServer is connected to a maximum of 8 SIMs by twisted pair copper wire (RS-485) and it polls data from the SIMs every few seconds
The iServer can be checked at any time from its LAN connection and will report conditions for 6 registers on all of the SIMs it is monitoring
If queried by a browser the current SIM conditions are presented as a web page
If queried by a separate program called the email Notifier, then just the key data is returned.
The email Notifier checks the iServer (or many iServers) every few seconds and compares the returned data against alarm thresholds
If any abnormal condition is detected an email is sent to a list of recipients which can be cell phones, pagers or regular email accounts
When a user gets a notification message on his cell phone he uses any web browser to get a display of current conditions on the SIMs
Private and Confidential
The Basic Requirements
1 to 8 SIMs (any variety) A TTDM is optional
You must use SIMs there is no connection to the SI card A local RJ41 Ethernet connection to a LAN A PC permanently connected to the same LAN
24/7 connectivity Ability to send email messages Very limited resource requirements so this application can run in the
background with other services A cell phone or pager to receive alarm messages Any PC that can connect to the LAN
May require VPN access if remote Must have a browser installed
Private and Confidential
Physical Set-up
Install the sensors and SIMs in normal TraceTek fashion Place the iServer on a DIN rail near an Ethernet LAN
connection. Provide 10 to 32 VDC (nominal load is 2W) (Terminals
marked + / - on the orange terminal block – removable) Connect the SIMs to the iServer in a typical RS485 daisy chain.
Check instructions for connection details Install the EOL jumper at the last SIM Normal RS485 limits apply … (could be 4000’ from last SIM to
iServer) Note down the last four digits of the iServer MAC address Flip the #3 DIP switch DHCP to ON Power everything up but hold off on connecting the RJ41
connection to the LAN
Private and Confidential
Networking and Commissioning
When the physical set-up is complete connect the iServer to the LAN by plugging in the Ethernet cable
What is supposed to happen: The iServer requests an IP address from the LAN’s DHCP server
(remember DIP switch #3)
The DHCP server allocates an IP address to the iServer
The iServer responds with its “name” which is eis followed by the last four digits of the MAC address: (e.g. eis38C3)
The DHCP server publishes the name on the local LAN segment so that any browser can cruise to http://eis38C3
If this doesn’t work there are alternatives spelled out in the installation instructions
Use any browser connected to the LAN to access the iServer and complete the set-up pages
Private and Confidential
Software Set-up
Each iServer has 8 slots that can be individually set-up Each slot can have any SIM address assigned to it In addition to the SIM address, a tag of 28 characters can be
entered Unused slots can be left blank Click iServer Setup and use password 12345678 On the iServer set-up page the default name can be changed to
something more meaningful than eis38C3. (e.g. TraceTek, Trace001, etc. Maximum of eight characters)
Feet or Meters can be selected The entire iServer itself can be assigned a useful tag (e.g.
Building 4 Leak Detection) maximum of 30 characters You can change the password to something other than
12345678 if desired
Private and Confidential
Installing the email Notifier
Find a suitable PC
Install Notifier from the CD
Add list of iServers to be monitored
Add list of email accounts to be notified
Enter local email account and password to send email
Enable email
Enable monitoring