procedimento de configuração de roteadores hp
TRANSCRIPT
-
8/20/2019 Procedimento de Configuração de Roteadores HP
1/91
H3C
MSR20_MSR30_MSR50_MSR900-CMW520-R2209P33-SI Release Notes
Copyright © 2012 Hangzhou H3C Technologies Co., Ltd. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any
means without prior written consent of Hangzhou H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
2/91
1
H3C
MSR20_MSR30_MSR50_MSR900-CMW520-
R2209P33-SI Release NotesKeywords: Version Information Unresolved Problems and Avoidance Measure
Abstract: The explication for this version, including Version Information, Unresolved
Problems and Avoidance Measure, Version Compatibility, Software Upgrading and so on.
Acronyms:
Acronym Full spelling
LAN Local Area Network
MAC Media Access ControlIGMP Internet Group Management Protocol
VLAN Virtual Local Area Network
STP Spanning Tree Protocol
RMON Remote Monitor(SNMP)
GMRP GARP Multicast Registration Protocol
ACL Access Control List
DHCP Dynamic Host Configuration Protocol
OSPF Open Shortest Path First
RIP Routing Information Protocol
ARP Address Resolution Protocol
AAA Authentication Authorization Accounting
RSTP Rapid Spanning Tree Protocol
PIM Protocol Independent Multicast
LPM Longest Prefix Match
QoS Quality of Service
UTP Unshielded Twisted Paired
SFP Small Form-Factor Pluggable
GBIC Gigabit Interface Converter
-
8/20/2019 Procedimento de Configuração de Roteadores HP
3/91
2
Table of Contents
Version Information ················································································································· 5
Version Number ······················································································································· 5
Version History·························································································································· 5 Hardware and Software Compatibility Matrix ············································································ 12
Upgrading restrictions and guidelines ······················································································· 15
Hardware feature updates ···································································································· 15
CMW520-R2209P33 ················································································································· 15
CMW520-R2209P26 ················································································································· 15
CMW520-R2207P08 ················································································································· 15
CMW520-E2103 ······················································································································ 16
CMW520-E1804 ······················································································································ 16
CMW520-B1707 ······················································································································ 16
CMW520-B1608 ······················································································································ 17
CMW520-B1506 ······················································································································ 17
Software feature and command updates ··············································································· 17
MIB Updates ························································································································· 17
Configuration Changes ········································································································· 21
Restrictions and Cautions ······································································································ 21
Open Problems and Workarounds ·························································································· 22
List of Resolved Problems ······································································································· 22 Resolved Problems in CMW520-R2209P33 ················································································· 22
Resolved Problems in CMW520-R2209P26 ················································································· 23
Resolved Problems in CMW520-R2209P21 ················································································· 24
Resolved Problems in CMW520-R2209P15 ················································································· 24
Resolved Problems in CMW520-R2209P13 ················································································· 25
Resolved Problems in CMW520-R2209P01 ················································································· 25
Resolved Problems in CMW520-R2209 ······················································································ 26
Resolved Problems in CMW520-R2207P45 ················································································· 27
Resolved Problems in CMW520-R2207P38 ················································································· 27
Resolved Problems in CMW520-R2207P34 ················································································· 28
Resolved Problems in CMW520-R2207P23 ················································································· 28
Resolved Problems in CMW520-R2207P14 ················································································· 29
Resolved Problems in CMW520-R2207P08 ················································································· 29
Resolved Problems in CMW520-R2207P02 ················································································· 30
Resolved Problems in CMW520-R2207 ······················································································ 31
Resolved Problems in CMW520-E2206 ······················································································· 31
Resolved Problems in CMW520-E1908P02 ·················································································· 32
Resolved Problems in CMW520-E1804 ······················································································· 32
Resolved Problems in CMW520-B1707······················································································· 32
Resolved Problems in CMW520-B1608······················································································· 33
Resolved Problems in CMW520-B1606······················································································· 34
Resolved Problems in CMW520-R1508P02&CMW520-B1508P02 ···················································· 35
Resolved Problems in CMW520-R1508&CMW520-B1508 ······························································ 35
Resolved Problems in CMW520-R1507 ······················································································ 36
Resolved Problems in CMW520-B1502······················································································· 36
Resolved Problems in CMW520-B1501L01 ·················································································· 37
Resolved Problems in CMW520-B1204P04 ················································································· 37
Resolved Problems in CMW520-B1204P03 ················································································· 37
Resolved Problems in CMW520-B1204L02 ·················································································· 37
-
8/20/2019 Procedimento de Configuração de Roteadores HP
4/91
3
Resolved Problems in CMW520-B1204L01 ·················································································· 38
Resolved Problems in CMW520-B1203······················································································· 39
Resolved Problems in CMW520-B1202P02 ················································································· 39
Resolved Problems in CMW520-B1202P01 ················································································· 39
Resolved Problems in CMW520-B1202······················································································· 39
Resolved Problems in CMW520-B1106······················································································· 40
Related Documentation ········································································································ 41
New Feature Documentation ·································································································· 41
Documentation Set ················································································································ 41
Obtaining Documentation ······································································································ 41
Technical support ················································································································· 42 Files ································································································································ 60
Software Maintenance Methods ······················································································· 62
Main BootWare Menu ······································································································ 63
BootWare Submenus ······································································································· 66
Introduction to XModem ·································································································· 69
Modifying Serial Port Parameters ······················································································· 69
Configuring Ethernet Parameters ······················································································ 73
Upgrading Application Program Through Ethernet Interface ················································ 75
Maintaining the Router with TFTP Server·············································································· 77
Maintaining the Router with FTP Server ··············································································· 79
Maintaining Application Program and Configuration File ····················································· 83
User Password Loss ··········································································································· 85
BootWare Password Loss ·································································································· 86
Super Password Loss ········································································································ 87
-
8/20/2019 Procedimento de Configuração de Roteadores HP
5/91
4
List of Tables
Table 1 Version history ................................................................................................................................. 5
Table 2 Hardware and software compatibility matrix .........................................................................12
Table 3 MIB updates..................................................................................................................................17
Table 4 Follow these steps to register the software: .............................................................................22
Table 5 MSR20-1X Series Hardware Features .........................................................................................43
Table 6 MSR20 Series Hardware Features ..............................................................................................44
Table 7 MSR30 Series Hardware Features ..............................................................................................45
Table 8 MSR30 -1X Series Hardware Features ........................................................................................46
Table 9 MSR50 Series Hardware Features ..............................................................................................47
Table 10 MSR 9XX Series Hardware Features .........................................................................................48
Table 11 MSR20_MSR30_MSR50_MSR900 series Module List ................................................................49
Table 12 MSR20_MSR30_MSR50_MSR900 Series Software Features ....................................................55
Table 13 Default names and types of the boot files ............................................................................60
Table 14 Description on the three configuration files ..........................................................................61
Table 15 Main BootWare menu ...............................................................................................................65
Table 16 BootWare serial submenu ........................................................................................................66
Table 17 Enter Ethernet interface submenu ..........................................................................................67
Table 18 File control submenu .................................................................................................................68
Table 19 BootWare operation submenu ................................................................................................68
Table 20 Ethernet parameters settings description ..............................................................................74
-
8/20/2019 Procedimento de Configuração de Roteadores HP
6/91
5
This document describes the features, restrictions and guidelines, open problems, and
workarounds for version R2209P33. Before you use this version in a live network, back up the
configuration and test the version to avoid software upgrade affecting your live network.
Use this document in conjunction with H3C
MSR20_MSR30_MSR50_MSR900-CMW520-R2209P33-SI Release Notes (Software Feature
Changes) and the documents listed in "Related Documentation".
Version Information
Version Number
MSR 20-20_MSR 20-21_MSR 20-40_MSR30-16_MSR 30-20_MSR 30-40_MSR 30-60_MSR
50-40_MSR 50-60_MSR 50-40 MPU-G2_ MSR 50-60 MPU-G2:
Comware software, Version 5.20, Release 2209P33, Standard
MSR9XX_MSR20-1X_MSR30-11_MSR30-1X:
Comware software, Version 5.20, Release 2209P33
Note: You can see the version number with the command display version in any view.
Please see Note
.
Version History
Table 1 Version history
Versionnumber
Lastversion
ReleaseDate
Release
typeRemarks
CMW520-R
2209P33
CMW520-
R2209P262012-08-21
Release
version
Support MSR20_30_50_900 series
Modified Features:
1. Logging in to the device
2. The specifications of ASBR LSP and BGP LSP
CMW520-R
2209P26
CMW520-
R2209P21 2012-07-23
Release
version
Support MSR20_30_50_900 series
Modified Features:1. Logging in to the device
CMW520-R
2209P21
CMW520-
R2209P15
2012-06-14
Release
version
Support MSR20_30_50_900 series
New Features:
1. Support map a nonstandard port to an
application layer protocol for NAT ALG
2. The console interface of MSR900 and
MSR920 support the function of the auxiliary
interface, and Only the MSR900 and MSR920
which's PCB versions are 3.0 or higher can
support this function.
CMW520-
R2209P19
Release
version
-
8/20/2019 Procedimento de Configuração de Roteadores HP
7/91
6
CMW520-R
2209P19
CMW520-
R2209P012012-06-14
Release
versionOnly support MSR9XX series
CMW520-R
2209P15
CMW520-
R2209P132012-05-17
Release
version
Support MSR20_30_50_900 series
New Features:
1. Support to auto-configure the router by USB
disk
2. Extend MSR50 OSPF maximum area amount
to 200
CMW520-R
2209P13
CMW520-
R2209P012012-04-23
Release
version
Support MSR20_30_50_900 series
New Features:
1. Support to disable the USB port using the
command
CMW520-R
2209P01
CMW520-
R22092012-03-28
Release
version
Support MSR20_30_50_900 series
New Features:
1. Support to filter packets based on MAC
Addresses, and any attempt to break this rule
must to be logged and to send a SNMP trap2. Support to assign IPv6 address of /127 prefix
on link interfaces
CMW520-R
2209
CMW520-
R2207P452012-02-14
Release
version
Support MSR20_30_50_900 series
New Features:
1. CWMP support for configuring multiple ACS
servers.
2. Support multicast UDPH function
3. Support to using the sub-address of the
interface sending and receiving RIP routes
CMW520-R
2207P45
CMW520-
R2207P382011-12-28
Release
version
Support MSR20_30_50_900 series
New Features:
1. Using the command of ―impedance
south-africa‖ to set the FXO interface‘s ringing
impedance
2. Support HUAWEI EC1261 3G modem
3. If The NAT and IPSEC functions were
enabled at the same interface, the command
of ―ipsec no-nat-process enable‖ can control
that packets don‘t do NAT transition before
IPSEC
4. Support of CWMP over AES-256 SSL tunnel
5. Support of CWMP (TR-069) over SSL for BIMSand the router
CMW520-R
2207P38
CMW520-
R2207P342011-11-18
Release
version
Support MSR20_30_50_900 series
New Features:
1. The MIM-G.SHDSL and FIC-G.SHDSL card
supported the Whip function
CMW520-R
2207P34
CMW520-
R2207P232011-10-19
Release
version
Support MSR20_30_50_900 series
New Features:
1. Support Huawei E261 3G modem and ZTE
MF190 3G modem
-
8/20/2019 Procedimento de Configuração de Roteadores HP
8/91
7
CMW520-R
2207P23
CMW520-
R2207P142011-09-15
Release
version
Support MSR20_30_50_900 series
New Features:
1. Delay to notify the status change of
interface
2. Support to encrypt HWTACAS Key
3. The Statistic information of the MFR main
interface included the input and outputpackets from sub-interface.
CMW520-R
2207P14
CMW520-
R2207P082011-08-17
Release
version
Support MSR20_30_50_900 series
New Features:
1. The number of NAT address pool was
extended to 64 from 32.
2. Support Sierra 250U and 308U 3G modem at
the MSR20/MSR30/MSR9XX router.
CMW520-R
2207P08
CMW520-
R2207P022011-07-15
Release
version
Support MSR20_30_50_900 series
New Features:
1. Support HUAWEI E173 WCDMA modem2. Support to Configure TPID on a Layer 3
Ethernet or VE interface, and to implement
VLAN termination.
3. Support to transit the
extendedVideoCapability field of H245
packets in the NAT ALG
4. Support the DVPN instance.
5. The QoS policy of main interface can apply
to sub-interface.
6. Support the Refer-by field of the SIP packets.
CMW520-R
2207P02
CMW520-
R22072011-06-23
Releaseversion
Support MSR20_30_50_900 seriesNew Features:
1. Support the statistics per classifier of nested
QoS
CMW520-R
2207
CMW520-
E22062011-05-19
Release
version
Support MSR20_30_50_900 series
New Features:
1. Call forwarding authority control
2. Support DAR MIB
CMW520-E
2206
CMW520-
E21032011-04-07
ESS
version
Support MSR20_30_50_900 series
New Features:
1. Support Novatel Modem MC760
2. Authorization again for AAA
3. The feature supports the VPN could visit the
other VPN by NAT
4. Support OSPF and NAT in bridge-template
interface
5. WCDMA 3G Modem
6. CDMA2000 3G Modem
7. TD-SCDMA 3G Modem
8. SIP TRUNKING
-
8/20/2019 Procedimento de Configuração de Roteadores HP
9/91
8
9. SRTP
10. L2VPN connected to L3VPN
11. NAT DMZ host and related features
12. SIP support for non early media negotiation
13. IPsec RRI
14. Allows you to configure NAT address
groups, NAT server, and attack protection
through TR069.
15. Support of routing protocols for 6VPE
16. BIDIR-PIM
17. OSPFv3 support for MCE
18. Voice support for TR104
19. BGP, OSPFv3 and ISISv6 support for IPv6
VPN BFD
20. Allows you to set a BGP update interval of
0.
21. Allows you to use domain names to specify
SNMP trap and log hosts.
22. TR069 supports the following memory and
CPU utilization nodes:
23. ACL configuration information display
filtering
24. A routing policy name can contain up to
64 characters.
25. Allows you to use names as BGP
community attributes
26. Permanent attribute for static routes
27. Continue feature for routing policy
28. E1POS and AM ports can send calling
numbers.
29. POS terminal access can use the source
address in the TPDU header to map POS
packets to specific POS applications.
30. POS terminal access allows you to specify
TCP source port numbers for POS applications.
31. Bloomberg MSR Source NAT
In NAT NOPAT mode (NOPAT dynamic entries
exist)
32. NAT support for discontinuous address
pools33. ISDN support for sending the
progress-indicator unit
34. An ACL name can contain up to 63
characters.
35. POS MIB and E1 POS MIB
36. SIP support for SRV and NAPTR
37. TR098
CMW520-E
2103
CMW520-
E1908P022010-03-24
ESS
version
Support MSR20_30_50_900 series
New Features:
-
8/20/2019 Procedimento de Configuração de Roteadores HP
10/91
9
1. Portal, RADIUS, and HWTACACS support for
multi-VRF
2.L2TP Auto Client
3.G729B audio codec, which supports G.729
Annex B
4.FXS interface support for calling name
5. NQA threshold alarming
6. Dot1p based remark for MPLS-EXP, which
allows you to implement priority scheduling on
an MPLS interface.
7.Virtual baudrate adjustment on the tunnel
interface
8.Support for 63-bit SIP authentication
username
9.ISDN trap, which provides the state change
traps of ISDN Layer-2
10.MQC MIB Index Persist, which enables MQC
MID indexes to survive reboots
11. Layer-3 interface support for LLDP, whichenables Layer-3 Ethernet interfaces to support
LLDP.
CMW520-E
1908P02
CMW520-
E18042009-09-18
ESS
version
Support MSR20_30_50 series(Add
MSR30-1Xseries and MSR9XX series)
New Features:
1. SIP-T‘s support for basic QSIG call
2. E&M non-signaling mode
3. Support for unidirectional media streams
4. Portal‘s support for mandatory web page
pushing5. Support for enhanced fax and modem
transparent transmission
6. Tunnel interfaces‘ support for the IPSec
encapsulation
7. Optimizing the QoS page
8. Embedded NMS
9. AAA‘s support for super authentication
10. SIP‘s support for the Join header
11. Voice products‘ support for Web NMS
This feature implements using Web to
configure voice products.
CMW520-R
1809P06
CMW520-
R18092009-09-09
Release
versionOnly support MSR30-11_30-1X
CMW520-R
1809
CMW520-
R18082009-09-09
Release
versionOnly support MSR20_MSR30
CMW520-R
1805
CMW520-
E18042009-06-26
Release
versionOnly support MSR 20-1X
CMW520-E
1804
CMW520-
B17072009-03-02
ESS
version
Support MSR20_30_50 series(include MSR20-1X
and MSR50 MPU-G2)
New Features:
-
8/20/2019 Procedimento de Configuração de Roteadores HP
11/91
10
1.P2P flow control feature
2. Enhances for ARP anti-attack
3. Configure a fixed sub interface throughWeb.
4. TEL_URL
5. DDNS collaboration with VPN
6. Customized IVR
7. POS terminal access
8.DMC
9. DNS supported on voice features
10.IPsec&IKE Monitor MIB
11.SIP session update
12.Enable the implementation of SIP on the
router compatible with Huawei SoftX standard
T38 fax, FAX \ MODEM pass through function.
Deleted Features: None.
CMW520-R1719P01
CMW520-R1710
2009-02-20Releaseversion
Only support MSR 30-11
CMW520-R
1710
CMW520-
B17072008-12-17
Release
versionOnly support MSR 20-1X
CMW520-R
1710
CMW520-
B17072008-09-14
Release
versionOnly support MSR 30-11
CMW520-B
1707
CMW520-
B16082008-06-23
Beta
version
Support MSR20_30_50 series(include MSR20-1X
and MSR50 MPU-G2)
1.QoS priority marking support on VLAN
interfaces
2.Encryption of configuration file
3.Enhanced Netstream
4.Traffic classification and queuing support on
PPPoE-enabled interfaces in bridging mode
5.Embedding CBQ in QoS
6.ISDN NAT Backup
Deleted Features: None.
Modified Features: None.
CMW520-R
1618P15
CMW520-
R1618P032008-10-15
Release
versionOnly support MSR20
CMW520-R
1618P03
CMW520-
R1617 2008-06-20
Release
version Only support MSR20-1X
CMW520-R
1618P01
CMW520-
R16172008-08-22
Release
versionOnly support MSR30_30-16
CMW520-R
1617
CMW520-
R16152008-04-09
Release
versionOnly support MSR20
CMW520-R
1615
CMW520-
B16082008-03-10
Release
versionOnly support MSR30-11
CMW520-B
1608P05
CMW520-
B16082008-01-18
Beta
versionOnly support MSR20-1X
-
8/20/2019 Procedimento de Configuração de Roteadores HP
12/91
11
CMW520-B
1608
CMW520-
B16062007-11-29
Beta
versionSupport MSR20_30_50 series(except MSR20-1X)
CMW520-B
1606
CMW520-
R1508P01
2007-10-19
Beta
version
Support MSR20_30_50(except
MSR30-11/MSR20-1X)
New Features:
1.ACSEI
2.VoiceVLAN support Cisco IP Phone
Deleted Features:None.
Modified Features:None.
CMW520-B
1605P01H0
1
CMW520-
R1508P012007-09-20
Beta
version MSR20-1X
CMW520-R
1508P02
CMW520-
R15082007-09-24
Release
versionSupport MSR20_30_50(except MSR30-11)
CMW520-B
1508P02
CMW520-
B15082007-09-24
Beta
versionOnly support MSR30-11
CMW520-R1508P01
CMW520-R1508
2007-09-20 Releaseversion
Only support MSR20_30
CMW520-B
1508
CMW520-
B1506P022007-09-07
Release
versionOnly support MSR30-11
CMW520-R
1508
CMW520-
R15072007-09-03
Release
version
None.
New Features:
1.DVPN
2.Terminal Access
3.Qos WRED support DSCP
4.Call forwarding
5.Call waiting
6.Call hold
7.Call transfer
8.Call backup
9.Hunt group
10.Call barring
11.Extended Portal
12.SNMP support VPN
Deleted Features:None.
Modified Features:None.
CMW520-R
1507
CMW520-
B15022007-08-02
Release
version
First time for the release version of
MSR30-16,and Support MSR20_30_50 (except
MSR30-11)
CMW520-B
1506P02
CMW520-
B1506P012007-08-02
Beta
versionOnly support MSR30-11
CMW520-B
1506P01
CMW520-
B15062007-07-05
Beta
versionOnly support MSR30-11
CMW520-B
1506
CMW520-
B15022007-06-18
Beta
version
First time for the release version of
MSR30-11,and only support MSR30-11
None.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
13/91
12
CMW520-B
1502
CMW520-
B1501L012007-04-24
Beta
versionFirst time for the beta version of MSR30-16
CMW520-B
1501L01
CMW520-
B1204L012007-02-06
Beta
versionLimited.
CMW520-B
1204P04
CMW520-
B1204P032007-02-01
Beta
versionResolved Problem
CMW520-B
1204P03
CMW520-
B1204L022007-01-30
Beta
versionResolved Problem
CMW520-B
1204L02
CMW520-
B12032007-01-25
Beta
versionLimited.
CMW520-B
1204L01
CMW520-
B12012007-01-19
Beta
versionLimited.
CMW520-B
1203P01
CMW520-
B12032006-12-30
Beta
versionLimited.
CMW520-B
1203
CMW520-
B1202P022006-12-27
Beta
versionResolved Problem
CMW520-B1202P02
CMW520-B1202P01
2006-12-06 Betaversion
Resolved Problem
CMW520-B
1202P01
CMW520-
B12022006-11-23
Beta
versionResolved Problem
CMW520-B
1202
CMW520-
B12012006-11-10
Beta
versionResolved Problem
CMW520-B
1201
CMW520-
B11062006-10-30
Beta
versionResolved Problem
CMW520-B
1106
CMW520-
B1105P012006-09-28
Beta
versionResolved Problem
CMW520-B
1105P01
CMW520-
B1105 2006-08-25Beta
version Resolved Problem
CMW520-B
1105None 2006-08-09
Beta
versionFirst time.
Hardware and Software Compatibility Matrix
Table 2 Hardware and software compatibility matrix
Item Specifications
Product
familyMSR20_30_50_900 series routers
Hardwa
re
platfor
m
MSR20-1X series: MSR 20-10_MSR 20-11_MSR 20-12_MSR 20-13_MSR 20-15
MSR 20-20_MSR 20-21_MSR 20-40
MSR30-11
MSR30-1X series: MSR30-10_MSR30-11E_MSR30-11F
MSR 30-16
MSR30-20_MSR 30-40_MSR 30-60
-
8/20/2019 Procedimento de Configuração de Roteadores HP
14/91
13
Item Specifications
MSR 50-40_MSR 50-60_ MSR 50-40 MPU-G2_MSR 50-60 MPU-G2
MSR9XX series: MSR 900_MSR920
Boot
ROM
version
MSR20-1X series: 226 or higher
MSR 20-20_MSR 20-21_MSR 20-40: 313 or higher
MSR30-11_ MSR30-1X series: 223 or higherMSR30-16: 212 or higher
MSR 30-20_MSR 30-40_MSR 30-60: 317 or higher
MSR 50-40_MSR 50-60: 315 or higher
MSR 50-40 MPU-G2_ MSR 50-60 MPU-G2: 122 or higher
MSR 9XX series: 117 or higher
(Note: Perform the command display version command in any view to view the version
information. Please see Note②)
Host
softwar
e
Hardware software MD5 Check Sum
MSR 20-20_MSR
20-21_MSR 20-40
MSR20-CMW520-R2209P21-SI
.BIN
c541858f8b13651136b303e03
51d0062
MSR20-1X seriesMSR201X-CMW520-R2209P21
.BIN
8c7e0e86f45b6fed0384b6b0c
838a62b
MSR 30-11MSR3011-CMW520-R2209P21
.BIN
be88510a3389d09897a9cffd0
7bb70a9
MSR30-1X seriesMSR301X-CMW520-R2209P21
.BIN
be88510a3389d09897a9cffd0
7bb70a9
MSR 30-16MSR3016-CMW520-R2209P21
-SI.BIN
5ee61ceec043f8d7f606bd3d5
1e2383a
MSR 30-20_MSR
30-40_MSR 30-60
MSR30-CMW520-R2209P21-SI
.BIN
aad04409516911fd91d52a102
b14949d
MSR 50-40_MSR 50-60MSR50-CMW520-R2209P21-SI
.BIN
08791c5fcb8b8bdaf37045908
3a56cf2
MSR 50-40 MPU-G2_ MSR
50-60 MPU-G2
MSR50-CMW520-R2209P21-E
PUSI.BIN
d519182f3fe51940e99c22a1a
722e9b3
MSR 900_MSR920MSR9XX-CMW520-R2209P21.
BIN
626e88e80fadfa44b77015e81
2418b7d
iMC
version
iMC PLAT 5.1 SP1 (E0202P05)
iMC UAM 5.1 SP1 (E0301P03)
iMC EAD 5.1 SP1 (E0301P03)
iMC MVM 5.1 SP1 (E0201P01)
iMC VSM 5.1 (E0201) (MSR9XX series not support VSM)
iMC QoSM 5.1 (E0201)
iMC TAM 5.1 (E0301)
iNode
versioniNode PC 5.1 (E0304)
TTYD
version4.27
OAA
version
OAA Name Version
OAP (1) MIM-OAP/ FIC-OAP version:
-
8/20/2019 Procedimento de Configuração de Roteadores HP
15/91
14
Item Specifications
Software: 130 or higher
(2) MIM-OAP-V2 version:
Software: 104 or higher
BIOS: 103 or higher
FPGA: 1.00 or higher(3) FIC-OAP-V2 version:
Software: 102or higher
BIOS: 102 or higher
FPGA: 1.00 or higher
OAPS
(1) MIM-OAPS version:
Software: 101 or higher
(2) MIM-OAPS-V2 version:
Software: 104or higher
BIOS: 101 or higher
FPGA: 1.00 or higher
OSM 128 or higher
ASM 102 or higher
NAM 200 or higher
WAAM 100 or higher
VCX VCX 9.5 or higher
Cards
Version
Cards Name Software Version CPLD or FPGA version
SIC-3G-GSM 180 or higher 200 or higher
SIC-3G-CDMA 180 or higher 200 or higher
SIC-3G-TD 180 or higher 200 or higher
SIC-AP R3200 or higher 200 or higher
SIC-ADSL-I/SIC-ADSL-P 230 or higher 100 or higher
MIM-6FCM/FIC-6FCM 230 or higher 100 or higher
SIC-EPON R3130 or higher 100 or higher
FIC-24FXS 200 or higher 100 or higher
DFIC-24FXO24FXS 200 or higher 100 or higher
SIC-2BSV/MIM-2BSV/FIC
-2BSV
None CPLD:200 or higher
VCPM:RTV1VCPM NoneCPLD:100 or higher
FPGA:400 or higher
Sample:To display the host software and Boot ROM version of the MSR routers, perform the
following:
display version
H3C Comware Platform Software
Comware software, Version 5.20, Release 2209P33, Standard ------- Note
-
8/20/2019 Procedimento de Configuração de Roteadores HP
16/91
15
Copyright (c) 2004-2012 Hangzhou H3C Tech Co., Ltd. All rights reserved.
H3C MSR50-60 uptime is 0 week, 0 day, 0 hour, 2 minutes
CPU type: FREESCALE MPC8541 833MHz
256M bytes DDR SDRAM Memory
4M bytes Flash Memory
Pcb Version: 3.0
Logic Version: 2.0
Basic BootROM Version: 3.10
Extend BootROM Version: 3.15 ------ Note
[SLOT 0]CON (Hardware)3.0, (Driver)1.0, (Cpld)2.0
[SLOT 0]AUX (Hardware)3.0, (Driver)1.0, (Cpld)2.0
[SLOT 0]GE0/0 (Hardware)3.0, (Driver)1.0, (Cpld)2.0
[SLOT 0]GE0/1 (Hardware)3.0, (Driver)1.0, (Cpld)2.0
[SLOT 11]FIX-SNDE (Hardware)3.0, (Driver)2.0, (Cpld)2.0
Upgrading restrictions and guidelines
Hardware feature updates
CMW520-R2209P33
None
CMW520-R2209P26
New features: TOSHIBA flash is supported on MSR 30-11E/MSR 30-11F/MSR 30-10/MSR
900/MSR 920.
Deleted features: None
CMW520-R2207P08
New Features:
Add new card:
Open Application Platform MIM Interface Module(Smart)-V2 (RT-MIM-OAPS-V2)
Open Application Platform MIM Interface Module-V2 (RT-MIM-OAP-V2)
Open Application Platform FIC Interface Module-V2 (RT-FIC-OAP-V2)
-
8/20/2019 Procedimento de Configuração de Roteadores HP
17/91
16
CMW520-E2103
New Features:
Add new card:
1-port SDH/SONET interface module FIC-1POS-V4;
1-port SDH/SONET interface module MIM-1POS-V2;
1-port channelized SDH/SONET interface module FIC-1CPOS;
1 port E1POS POS-terminal access module FIC-E1POS;
4-port voice subscriber circuit & 1-port voice AT0 analog trunk interface card
-DSIC-4FXS1FXO
CMW520-E1804New Features:
Add new card:
1-port EPON interface card (SIC-EPON);
3G WLAN access module (SIC-3G-GSM);
802.11b/g WLAN access module (SIC-WLAN-b/g);
802.11n WLAN access module (SIC-WLAN-n).
CMW520-B1707
New Features:
Add new card:
RT-SIC-1E1-F-H3
RT-SIC-2E1-F-H3
RT-MIM-8FXS-8FXO-H3
RT-MIM-16FXS-H3
RT-MIM-1CT3-V2-H3
RT-MIM-1CE3-V2-H3
RT-MIM-1ATM-OC3-H3
RT-DMIM-48FSW-H3
RT-FIC-1CE3-V3-H3
-
8/20/2019 Procedimento de Configuração de Roteadores HP
18/91
17
RT-FIC-1CT3-V3-H3
RT-FIC-1ATM-OC3-H3
Deleted Features:None.
CMW520-B1608New Features:
Add 2-port voice subscriber circuit & 1-port voice AT0 analog trunk interface
card(SIC-2FXS1FXO);
1/2-port ISDN BRI S/T voice interface card can be supported on MSR20/30/50series and
MSR30-11/30-16.(the card can not be support on 2 slot of MSR30-11).
Deleted Features:None.
CMW520-B1506
New Features:MSR3011, Please make reference to Table4.
Deleted Features:None.
Modified Features:None.
Software feature and command updates
For more information about the software feature and command update history, see H3C
MSR20_MSR30_MSR50_MSR900-CMW520-R2209P33-SI Release Notes (Software Feature
Changes).
MIB Updates
Table 3 MIB updates
Version
Number ItemMIB File
Name
Module
Name Description
CMW520-R
2209P01
New None None None
Modi
fied
hh3c-confi
g-man.mib
HH3C-CONFIG-
MAN-MIB
Modified the description of
hh3cCfgLogTerminalUser in
hh3cCfgLogTable
Delet
edNone None None
CMW520-R
2209
New None None None
Modi rfc1213.mi RFC1213-MIB Modified all the descriptions
-
8/20/2019 Procedimento de Configuração de Roteadores HP
19/91
-
8/20/2019 Procedimento de Configuração de Roteadores HP
20/91
19
Hh3c-e1t1
vi.mib
HH3C-E1T1VI-MI
B
Add
hh3cE1T1VITrapTimeSlotEnabl
e
hh3c-e1.mi
bHH3C-E1-MIB
Add hh3ce1FcmChannelIndex
and hh3ce1TimeSlotSetTable
Modi
fied
hh3c-splat-mstp.mib
HH3C-LswMSTP-MIB
Modified the description of
hh3cdot1sMstAdminFormatSelector. Changed the value
range from [0..255] to 0
hh3c-dhcp
s.mib
HH3C-DHCPS-M
IB
Modified the description of
hh3cDHCPSGlobalPoolLeaseU
nlimited. Added the value
can‘t be set to 0
rfc1657-bg
p4.mibBGP4-MIB
Modified the PDS of
bgpeerAdminStatus,
bgpPeerHoldTimeConfigured,
bgpPeerKeepAliveConfigure
d,
bgpPeerMinASOriginationInterval and
bgpPeerMinRouteAdvertisem
entInterval
Hh3c-posa
.mib
HH3C-POSA-MIB
Modified the PDS of
hh3cPosaTerminalTable and
hh3cPosaAppTable
Delet
edNone None None
CMW520-E
2103New
hh3c-radiu
s.mib
HH3C-RADIUS-
MIB
Addedhh3cRadiusAuthErrThredsholdin HH3C-RADIUS-MIB
hh3c-pppo
e-server.mi
b
HH3C-PPPOE-SE
RVER-MIB
Added
HH3C-PPPOE-SERVER-MIB
hh3c-dhcp
-server.mib
HH3C-DHCP-SE
RVER-MIB
Added
hh3cDHCPServerAvgIpUseThr
eshold,
hh3cDHCPServerMaxIpUseThr
eshold,
hh3cDHCPServerAllocateThre
shold in
hh3cDHCPServerObjects in
HH3C-DHCP-SERVER-MIB
hh3c-ip-ad
dress.mib
HH3C-IP-ADDRE
SS-MIB
Added
hh3cIpAddrNotifyScalarObjec
ts in HH3C-IP-ADDRESS-MIB
hh3c-3gm
odem.mib
HH3C-3GMODE
M-MIBAdded HH3C-3GMODEM-MIB
hh3c-isdn.
mibHH3C-ISDN-MIB
Added
hh3cLapdStatusTrapEnable
and
hh3cLapdIsdnStatusChange
in HH3C-ISDN-MIB
-
8/20/2019 Procedimento de Configuração de Roteadores HP
21/91
20
rfc2128-dia
l-control.mi
b
DIAL-CONTROL-
MIBAdded DIAL-CONTROL-MIB
hh3c-voice
-call-activ
e.mib
HH3C-VOICE-C
ALL-ACTIVE-MIB
Added
HH3C-VOICE-CALL-ACTIVE-MI
B
hh3c-voice-dial-contr
ol.mib
HH3C-VOICE-DIAL-CONTROL-M
IB
AddedHH3C-VOICE-DIAL-CONTROL-
MIB
rfc1213.mi
bRFC1213-MIB
Added RFC1213 IP Group and
ICMP Group
lldp.mib LLDP-MIB Added LLDP-MIB
lldp-ext-do
t1.mib
LLDP-EXT-DOT1-
MIBAdded LLDP-EXT-DOT1-MIB
lldp-ext-do
t3.mib
LLDP-EXT-DOT3-
MIBAdded LLDP-EXT-DOT3-MIB
Modi
fied
hh3c-isdn.mib
HH3C-ISDN-MIB
Modified
hh3cLapdIsdnProtocol in
HH3C-ISDN-MIB
hh3c-flash-
man.mib
HH3C-FLASH-M
AN-MIB
Modified description of
hh3cFlhOperType in
hh3cFlhOpTable of
HH3C-FLASH-MAN-MIB
rfc2465-ipv
6.mibIPV6-MIB
Modified route scalar objects
and ipv6RouteTable of
IPV6-MIB
hh3c-splat-
inf.mib
HH3C-LswINF-MI
B
Modified description of
hh3cMaxMacLearnRange of
HH3C-LswINF-MIB
rfc4444-isis.
mibISIS-MIB
Changed describe of
isisSysWaitTime of ISIS-MIB to
support read operation
ieee8023-l
ag.mib
IEEE8023-LAG-
MIB
Modified description of
dot3adAggPortActorAdminSt
ate of IEEE8023-LAG-MIB
hh3c-cbqo
s2.mib
HH3C-CBQOS2-
MIB
Modified description of
hh3cCBQoSMatchRuleType of
HH3C-CBQOS2-MIB
Delet
ed
None None None
CMW520-E
1908P02
Newrfc2662-ad
sl-line.mib ADSL-LINE-MIB Added ADSL-LINE-MIB
Modi
fiedNone None None
Delet
edNone None None
CMW520-B
1608 Delet
ed
h3c-e1t1vi.
mibH3C-E1T1VI-MIB
Added whole module of
h3c-e1t1vi.mib
huawei-dh HUAWEI-DHCPS Add hwDHCPSIPInUseExTable
-
8/20/2019 Procedimento de Configuração de Roteadores HP
22/91
21
cps.mib -MIB to HUAWEI-DHCPS-MIB
Modi
fied
rfc2819
MIB.mib RMON-MIB
Modify descripsion Not
supported. When eventType is
none(1) or log(2), the value of
eventCommunity will not be
saved; when eventType is
snmptrap(3) or logandtrap(4),
the value of eventCommunitywill be saved but can take no
effect.
ieee8021x.
mib
IEEE8021-PAE-M
IB
Modify descripsion Only valid
on portbased method.
h3c-acl.mi
b H3C-ACL-MIB
When the value of
h3cAclIPAclAdvancedProtoc
ol is ICMP or ICMPV6,
h3cAclIPAclAdvancedIcmpTy
pe and
h3cAclIPAclAdvancedIcmpC
ode can be set, otherwise it
can not.
Delet
ed
huawei-spl
at-mam.mi
b
HUAWEI-LswMA
M-MIB
Deleted
hwdot1qMacSearchTable
CMW520-R
1508P02
New None. None. None.
Modi
fied
hh3c-user.
mibHH3C-USER-MIB
Modify h3cUserIndex PDS
attribute to "No".
hh3c-radiu
s.mib
HH3C-RADIUS-
MIB
Modify h3cRdAccRealTime
Description to "As per mib".
rfc4133-ent
ity.mibENTITY-MIB Modify "AR" to "MSR".
Delet
edNone. None. None.
Configuration Changes
None.
Restrictions and Cautions1. The versions of MSR30-11 can‘t boot based on 16M FLASH.
2. Software register is provided on the device to protect the authorized users‘ legal rights to
use the software. Trial period is set on the software with this function and users are required
to register the serial number of the software in the trial period. If the software has not been
registered until the trial period expires, the system automatically restarts every 30 minutes.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
23/91
22
You can obtain a registration serial number through buying letter of authorization of the
software.
You can use the license register serial-number command or log onto the network
management interface and then enter the serial number to finish software registration; and
you can use the display license command or log onto the network management interface
to view the soft registration information of the device.
Table 4 Follow these steps to register the software:
To do... Use the command... Remarks
Register the softwarelicense register
serial-number
Required
Available in user view
Display the information display license any view
CAUTION:
H3C MSR 20-1X, MSR 30-11, MSR 30-1X and MSR 9XX not support Software register!
3.
It is recommended that the MSR900 and MSR920 which's PCB versions are 3.0 or higher
use the software R2209P19 or later versions. If the old software versions are used, the
console interface of the MSR900 and MSR920 will be flow controlled, and it is necessary to
forbid detecting the RTS/CTS signal at the terminal software in order to manage the
console interface normally.
Open Problems and WorkaroundsNone.
List of Resolved Problems
Resolved Problems in CMW520-R2209P33
RTD063126
Description: UDP Helper enabled on a VLAN interface works abnormally.
Condition: This symptom might occur on a VLAN interface configured with the udp
helper server command.
RTD062784
Description: The idle timer on a dialer interface that is a member port of an MP
interface does not take effect. As a result, the link on the dialer interface cannot be
automatically torn down when the idle timer expires.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
24/91
23
Condition: This symptom might occur when the following conditions exist:
The MP interface comprises multiple dialer interfaces that have come online.
The dialer threshold and dialer timer commands have been configured on the
target dialer interface.
Resolved Problems in CMW520-R2209P26
RTD062342
Symptom: Memory leaks occur if an ADSL port configured with MPPPoA has forwarded
large amounts of traffic for a certain time.
Condition: This symptom might occur if an ADSL port configured with MPPPoA has
forwarded large amounts of traffic for a certain time.
RTD062305
Symptom: A router reboots after processing H323 and ISDN DSS1 calls for a long time.
Condition: This symptom might occur if the router is installed with multiple VE1 cards
and has processed H323 and ISDN DSS1 calls for a long time.
RTD062240
Symptom: A walk of the RFC1213 ifConnectorPresent MIB node on a subinterface
returns an incorrect value.
Condition: This symptom can be seen after a walk of the RFC1213 ifConnectorPresent
MIB node on a sub interface.
RTD062168
Symptom: The URI in the SIP header fields translated by NAT ALG has an error, resulting
in a call failure.
Condition: This symptom might occur if the URL in the SIP header field uses TEL_URL
format.
RTD062634
Symptom: Transient traffic interruption occurs on the fixed FSW interface of MSR 30-11F
when the maximum number of MAC addresses is configured on the interface.
Condition: This symptom might occur if the maximum number of MAC addresses is
configured on the fixed FSW interface of MSR 30-11F.
RTD062492
Symptom: Packet loss occurs on a POS port if 80 M user traffic or more is forwarded on
the port.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
25/91
24
Condition: This symptom might occur if 80 M user traffic or more is forwarded on the
POS port and most packets are smaller than 256 bytes packets because a POS port
cannot forward large amounts of small packets.
RTD062139
Symptom: An MSR 30-11E cannot receive multicast and broadcast packets if the
configured multicast or broadcast suppression threshold is smaller than 190pps.
Condition: This symptom might occur if the configured multicast or broadcast
suppression threshold is too small.
RTD062766
Symptom: The fixed GE0/GE1 interfaces of MSR 30 series might receive and send
packets abnormally.
Condition: This symptom might occur on some MSR 30 routers because the chips used
by these routers have defects.
Resolved Problems in CMW520-R2209P21
RTD062073
Description: Because the external 3G modem negotiates slowly, if the PPPoE client
waits for PPP negotiation more than 10s, the PPPoE dialer will fail.
Condition: MSR device as PPPoE client, and connected with external 3G modem.
RTD061928
Description: The power level measured is greater than the maximum power level
allowed by the standard 12.5dBm.
Condition: The test house carries out the Annex L testing for the SIC-ADSL card.
RTD061985
Description: The UMTS light on the SIC-3G-GSM or SIC-HSPA card is bright yellow all
along.
Condition: The SIM card can‘t be identified in the SIC -3G-GSM or SIC-HSPA.
Resolved Problems in CMW520-R2209P15
RTD061429
Description: When modifying the parameter of tunnel bandwidth, OSPF COST doesn‘t
update.
Condition: The tunnel interface of the route runs OSPF protocol.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
26/91
25
RTD61366
Description: The REINVITE message from the router doesn‘t take NTE capacity filed, so
the FAX passthrough with LYNC server fails.
Condition: The router runs FAX passthrough with Microsoft LYNC server.
RTD061122Description: The router doesn‘t eliminate the NAT session synchronously at the router,
so that the NAT data flow can be transmitted all along.
Condition: Remove the NAT static configuration at the router, at the same time there
are durative NAT data flow at the router.
Resolved Problems in CMW520-R2209P13
RTD060728
Description: Some time, the E1-F interface is UP and DOWN ceaselessly.
Condition: A SIC-2E1-F card is inserted into the router, and the link status of one E1-F
interface is UP, the link status of the other E1-F interface is DOWN.
RTD60727
Description: The router can‘t detect the RPS power status accurately, so there are lots
of RPS power alarms at the LOG of the router.
Condition: The MSR30 router with RPS power.
RTD60721
Description: Once the interface bearing the BGP connection is UP/DOWN, the BGP
connection will be UP/DOWN again and again, and it takes a long time to establish
the steady BGP connection.
Condition: There are lots of BGP route policies about community attribute at the router,
and there are also many of BGP routes at the router.
RTD60720
Description: The GTS characteristics (CIR, CBS, EBS) based on the real bandwidth
negotiated by the router on the display information are error.Condition: Set the QoS GTS policy at the ATM interface of the router.
Resolved Problems in CMW520-R2209P01
RTD60406
Description: The router rebooted abnormally.
Condition: Insert some USB facility which the router can‘t support into the router.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
27/91
26
RTD60172
Description: Certain instance, EC1261 doesn‘t reply BULK OUT ACK to the router for two
seconds, so the router can‘t identify the EC1261.
Condition: The router connects HUAWEI EC1261 MODEM.
RTD60042Description: After a long time, the FSW card can‘t forward multicast and broadcast
packets.
Condition: The 16FSW or 24FSW card at the router runs three layer packets, and the
other interfaces of the router forward large numbers of packets.
RTD59907
Description: E160 MODEM reboots again and again.
Condition: The router connects HUAWEI E160 MODEM.
RTD59895
Description: Period of time, The SIC-1T1-F card can‘t receive and send packets, and
the interface queue is plugged up.
Condition: The POE router is inserted into FSW-POE card and SIC-1T1-F card.
RTD60199
Description: The SNMP OID hh3cCfgLogTerminalUser value is error.
Condition: None.
Resolved Problems in CMW520-R2209
RTD59161
Description: When transmits some UDP packets, the router will reboot abnormally.
Condition: The router runs NAT function, and there are several NAT outbound
commands at the interface of the router.
RTD58793
Description: The result of NQA was inaccurate.
Condition: Run NQA function in the Multilink PPP link with several physical interfaces.
RTD58598
Description: The line protocol status of the async interface is always down.
Condition: The aysnc interface of the router works at flow mode.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
28/91
27
RTD59306
Description: OSPF Area 0 ABR does not generate default to stub when no neighbor in
Area 0.
Condition: Run OSPF protocol in the router.
Resolved Problems in CMW520-R2207P45
RTD58789
Description: If the router received challenge more than 16 bytes, the PPP CHAP
authentication failed.
Condition: The interface of the router set PPP protocol and CHAP authentication.
RTD58508
Description: The router can‘t identify the INARP packets with filled information, so therouter failed to parse the IP address.
Condition: None.
RTD57556
Description: Because the BGP timer of the router was inaccurate, the BGP neighbors
were UP and DOWN again and again.
Condition: The CPU usage of the router was high.
Resolved Problems in CMW520-R2207P38RTD57850
Description: There wasn‘t the command to adjust the cable attenuation parameters
at the IMA-T1 interface of the router.
Condition: None.
RTD57858
Description: The pulse shape of IMA-T1 interface was too low.
Condition: None.
RTD58297
Description: The pulse shape of SIC-EPRI interface has overshot /undershot.
Condition: None.
RTD58164
Description: The pulse shape of IMA-E1 interface was too low.
Condition: None.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
29/91
28
RTD57892
Description: When the router received the SIP packets which‘s record-route and
contact head field the Transfer Protocol were inconsistent, because the router
selected the error Transfer Protocol the voice call failed。
Condition: The router as VOICE gateway connected with AYAYA .
RTD57811
Description: The dialer connection can‘t establish.
Condition: The Dialer interface of the router set chap authentication for call-in
connection.
RTD58221
Description: The router rebooted abnormally.
Condition: Execute the command of ―display ip flow-ordering statistic internal‖ at the
router.
Resolved Problems in CMW520-R2207P34
RTD57852
Description: After the BFD session at the router was DOWN, the router would delete
correlative RIP routes, but the router still sent the RIP packets from the interface. If the
interface was broken down in the one direction, another end could still received the
rip packets.
Condition: The router started RIP BFD function.
RTD57785
Description: If the router received the SIP messages which the contact filed of was
included the maddr parameter, the voice call from the router was unsuccessful.
Condition: The router worked with some SIP SERVER, and established voice calls.
RTD57105
Description: The router reboots itself randomly.
Condition: The MSR30 router has 2 x 512M memories.
Resolved Problems in CMW520-R2207P23
RTD57286
Description: Occasionally the router can‘t recover from PPP state-machine and can‘t
dialup 3G-link successfully.
Condition: The router doesn‘t receive connect information from 3G modem.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
30/91
29
RTD57514
Description: The 3G interface of the router would be UP and DOWN.
Condition: 3G network was HSPA+.
RTD57365
Description: Because the SDP‘s fmtp and rtpmap of the SIP packet negotiated by error,
the compression selected was wrong.
Condition: The router established the SIP connection with other equipment.
RTD57500
Description: The packet which matching this route can‘t be transmitted.
Condition: MPLS L3VPN, inter-AS option B, a route advertising to ASBR through different
VPN-instance and the route is flapping.
Resolved Problems in CMW520-R2207P14RTD56973
Description: The 3G interface would be UP and DOWN because 3G network was
unstable.
Condition: 3G network status was unstable, little the network was no service.
RTD56986
Description: The router would turn off the FAX function, and brought on that the FAX
failed.
Condition: The router received the SIP INVITE message without a=T38MaxBitRate filed
to transfer T.38.
Resolved Problems in CMW520-R2207P08
RTD56520
Description: Even though the RIP BFD session was down, the RIP routes were updated.
Condition: Configuring RIP BFD at the router, the link was uni-direction and the router
could receive the RIP packets.
RTD56390
Description: The router couldn‘t get the Calling number and Called Number attribute
from LAC.
Condition: The router acted as LNS, and LAC sent the ICCN packets without Proxy auth
attribute.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
31/91
30
RTD56145
Description: Because the router didn‘t take offset filed in the L2TP packets, the L2TP
connection couldn‘t establish.
Condition: The router acted as LNS, and LAC requested the L2TP packets received
with offset field.
Resolved Problems in CMW520-R2207P02
RTD56119
Description: The router will reboot possibly.
Condition: If change the DVPN tunnel-protocol when there is IP traffic going out of the
tunnel.
RTD56062
Description: The IPSec policy groups cannot be modified successfully if the virtual
interface is deleted first.
Condition: Apply two or more IPSec policy groups to a virtual interface on the web
interface, like interface tunnel.
RTD56060
Description: The router made mistake when negotiating about the codec, it resulted in
that the FAX failed.
Condition: The router received the SIP packet of ―200 OK‖ without
―a=silenceSupp:off‖.
RTD56106
Description: The DAR function was abnormal and couldn‘t identify the packets
correctly.
Condition: The packets were identified by DAR after the packets were transmitted
through L2TP tunnel.
RTD55818
Description: The E1 POS calls failed.Condition: The E1POS interface worked with ISDN signal, and established the ISDN
connection with ALCATEL PBX.
RTD56103
Description: The MSR router as RTA client couldn‘t establish connection with RTA relay.
Condition: The AR46 or AR28 router worked as RTA relay.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
32/91
31
Resolved Problems in CMW520-R2207
RTD54811
Description: The instant message cannot be relaid.
Condition:
When using UDP as the SIP transport protocol, If the Packet is huge, the MSR
cannot re-build the SIP fragment messages.
RTD54836
Description: The call cannot be established.
Condition: When configure the UDP as the SIP transport protocol, If the Packet is larger
than MTU-200, the transport protocol will automatically change to TCP, but if the
destination does not support TCP, the transport protocol cannot change back to UDP.
Resolved Problems in CMW520-E2206RTD54077
Description: The router will restart by exception.
Condition: Forwarding multicast packets incessantly through many subinterfaces.
RTD53933
Description: The route is not compatible with some brand of POS terminal device.
Condition: Work with some brand of POS terminal device.
RTD53990
Description: It shows as "dialer call-in * callback 2", with a parameter "2" unwanted,
while the function of callback works fine.
Condition: Configure "dialer call-in * callback" in Bri interface.
RTD53973
Description: After the call established, when the voice switches to the standard T.38
fax, the source-bind function will be unusable.
Condition: More than one interfaces can be used on router, use sip as the voip callsignal and the standard T.38 as the fax protocol, and configure the source-bind
command.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
33/91
32
Resolved Problems in CMW520-E1908P02
RTD39984
Description: After reboot, the web login function through http will be disabled and
command "ip http enable" must be configured once again to enable it.
Condition: After enable CWMP, save the configuration and reboot the router.
Resolved Problems in CMW520-E1804
RTD31107
Description: The router forwards the packets to front-machine, and the front-machine
stop to send packets.
Condition:
When terminal unit sends soft-flowcontrol packets which including 0x11 or0x13 to the router.
RTD32332
Description: The DLSW connections can't be created successfully.
Condition: When DSLW create connections through sub Ethernet interface or
vlan-interface which work on bridge-forwarding mode.
ZDD01828
Description: The relay function failed.
Condition: ARP detection tries to work with DHCP relay function.
Resolved Problems in CMW520-B1707
RTD21682
Description: PPP will send negotiated packets from this interface anyway.
Condition: Running shutdown on BRI interface or physical interface of PRI, then
configuring ISDN Leased Line on it.
RTD21683
Description: the connection will always break down when 1 second is time out.
Condition: Configuring one Ethernet interface as PPPoE Client by pppoe-client
dial-bundle-number 101 idle-timeout 1, despite there are packets received during 1
second.
HSD33072
Description: The backup interface will flap (up/down) one time.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
34/91
33
Condition: Reboot router when implemented the Interface-backup feature.
LSD26984
Description: The fallback authentication will not happen.
Condition: If the connect with the TACACS is lost.
RTD27056
Description: The tunnel can't up.
Condition: Implemented MPLS TE tunnel and keep the reservable-bandwidth equal to
tunnel BC0.
Resolved Problems in CMW520-B1608
RTD21639
Description: RM will print some redundant information.
Condition: Input shutdown on one Encrypt interface.
RTD21642
Description: The statistic doesn‘t clean.
Condition: Enable IPV6 and configure IPV6 address on one interface, then get the
statistic of interface‘s packets after it received some IPV6 packets by display ipv6
interface XXX verbose. After that, reset ipv6 statistic and display ipv6 interface XXX
verbose again.
RTD20985
Description: System will print error info that PVC on the ATM interface has been
deleted.
Condition: Create PVC on the ATM interface and configure map bridge-group
broadcast on it, then configure atm-class and apply class on the interface.
RTD21516
Description: The reset operation will fail.
Condition: Configuring more than 4251 mboundarys on router ‘s interface, then reset
some of them with high speed packets received by the interface.
RTD21151
Description: The syntax of prompt info and debug info are not identical.
Condition: When dhcp-snooping is enable, print dhcp-snooping to get the prompt
info, then run undo dhcp-snooping and dhcp-snooping again, to get the debug info.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
35/91
34
RTD21384
Description: When the client accesses the server with not idlesse, the server will always
disconnect it.
Condition: Configuring router as SFTP server, setting it‘s idle time by sftp server
idle-timeout several.
RTD21352
Description: The flow control is not shown in the result.
Condition: Enable flow control on GEC interface and get the info by display interface.
RTD21406
Description: It doesn‘t contain default value of transparent transmission on modem.
Condition: Get voice and fax default value by display voice default all.
RTD21577
Description: The default IP address by product will lose.
Condition: During the boot if the interface 0/0 is up.
Resolved Problems in CMW520-B1606
RTD16324
Description: The router will reboot with exception notification.
Condition: To download software from FTP server to overwrite the file with same name.
RTD16521
Description: Ce as the NTP client can't synchronize with PE.
Condition: In the network of MPLS, to change the timer value of PE which is worked as
NTP server.
RTD17038
Description: The remote interface receives the loopback code and is set as mode of
loopback payload.
Condition: To set t1 x set fdl ansi on T1 channel of local side, and set t1 x set fdl att on
the same T1 channel of remote side, then sent loopback code on local side with
command t1 x sendloopcode fdl-ansi-payload-up.
RTD17152
Description: Telnet is failed.
Condition: Two routers are connected with transmission equipments and try to telnet
from the VLAN interfaces of the two routers.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
36/91
35
RTD17375
Description: The call process will be failed.
Condition: Two routers are connected to each other with VE1 and VT1, to launch call
and delete R2 configuration of VE1 or VT1 on one router during call processing.
Resolved Problems in
CMW520-R1508P02&CMW520-B1508P02
RTD20541
Description: The calling will fail.
Condition: The calling number less than 6, and the Q931 section of SETUP message
from calling device does not include CALLED PARTY NUMBER and CALLing PARTY
NUMBER.
RTD19553
Description: The flow-control function doesn‘t take effect.
Condition: Configuring flow-control on the interface of SIC-1GEC, and send high
speed data to it.
RTD20307
Description: The value of entPhysicalSoftwareRev not matches the version number
exactly.
Condition: walk iso ---> mgmt ---> entityMIB ---> entPhysicalEntry --->
entPhysicalSoftwareRev‘s sub-node entPhysicalEntry and get value of
entPhysicalSoftwareRev by MIB Browser, then _display version to get the version
number.
Resolved Problems in
CMW520-R1508&CMW520-B1508
RTD18997
Description: The route will reboot.
Condition: The VE1 interface connected to switch with PRI signaling and received
FACILITY information from remote switch.
RTD18437
Description: The call cannot be established.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
37/91
36
Condition: The user call a telephone with the VoIP system of H3C and the called
telephone has been set call forward.
RTD19880
Description: The data transmit forward by the ASE interface is error.
Condition: The user set reserve telnet and disable auto-negotiation.
RTD19991
Description: The default idle code is not 0x7e.
Condition: The 4BS interface works in the mode of BRI leased line.
RTD19852
Description: The user can not configure the router by com or telnet.
Condition: Using the English version of hyper terminal.
Resolved Problems in CMW520-R1507
RTD18219
Description: The 2GE port halts receiving and transmitting data.
Condition: The mode of 2GE module is 100M/full duplex and forwards the packets. The
length of packets is random.
Resolved Problems in CMW520-B1502
RTD13802
Description: The hookoff configuration in the FXO interface will lose.
Condition: Configuring ‗hookoff-time 36000‘ in a FXO interface and then resetting this
card.
RTD13055
Description: The configuration of Ioopback internal will be unsuccessful.
Condition: The user enables loopback-detection and configures ‗loopback internal‘in
a L2 port when stp function has been enabled.
RTD14199
Description: All commands can not be identified.
Condition: A sub-interface in an IMA-group has been set up. The user hot-plugs this
IMA card and then inserts it to the same slot.
HSD14531
Description: The information of DCD, DTR, DSR, RTS and CTS is error.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
38/91
37
Condition: A DCE cable has been inserted in a SAE interface, but not connected to
remote terminal. The user configure asynchronous physical mode and display
information of this interface.
RTD15139
Description: VI(Visual Identity) modified from Huawei-3com to H3C.
Condition: None.
Resolved Problems in CMW520-B1501L01
RTD13013
Description: The information table for current calls (shown by command display voice
call-info) will not be clear.
Condition: Hunt-group function has been enabled when call connection is set up by
IVA(ISDN Voice Application) . The matched voice entity is unavailable.
Resolved Problems in CMW520-B1204P04
RTD12924
Description: The port will receive too many incorrect packets and 8E1 ports can not
work normally.
Condition: 8E1 ports communicate through fiber network. When one port‘s remote
fiber terminal is turned off.
Resolved Problems in CMW520-B1204P03
RTD12559
Description: These packets can not be transmitted in VLAN.
Condition: The Ethernet L2 switching module receives ISIS Hello packets.
RTD12700
Description: The stream statistic doubles on the device, and the stream log is send to
XLOG server.
Condition: Applying Netstream on both inbound and outbound of one interface .
Resolved Problems in CMW520-B1204L02
RTD12640
Description: VRRP can not support tracking MP-group ports.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
39/91
38
Condition: Configuring VRRP on the MRS50 device.
Resolved Problems in CMW520-B1204L01
RTD07017
Description: The grading will fail.
Condition: Upgrade the router by Quidview.
RTD11696
Description: The data can not be transmitted and the configuration on the VLAN will
lose.
Condition: Keeping data flux on 4FSW in MSR routers.
LSD08869
Description: It can not get IP address in the overdue pool.
Condition:
DHCP client has no IP address in free pool,but there is available IP address
in the overdue pool.
RTD11776
Description: The system will hint ‗OSPF Interface Not enabled‘.
Condition: The user configures network command in an ospf interface and then
displays this interface information.
RTD11378
Description: The value of TTL is error.
Condition: The user configures fast-forwarding by encryption cards and runs ping
command.
RTD11954
Description: The first calling number and the second one are not identical.
Condition: Enabling Radius and DPL, and then running one time dialing and two times
dialing operation.
RTD11646
Description: It can not set up ISIS.
Condition: Connecting MSR routers with Cisco devices, setting both interfaces‘ ISIS
type p2p and configuring bridge on MSR router ‘s interface.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
40/91
39
Resolved Problems in CMW520-B1203
RTD10154
Description: The interfaces states can not be up.
Condition: Connecting SIC-E1 interfaces between two MSR20 serious routers, and
enable using e1.
Resolved Problems in CMW520-B1202P02
RTD11296
Description: Only the calling from the router to it‘s connecter is success, the other
direction calling is not normal.
Condition: configuring the router and it‘s connecter in G711U coding mode, andturning on VoIP.
Resolved Problems in CMW520-B1202P01
HWD05620
Description: It can not boot.
Condition: Keeping one ESM and one VCPM on the MSR30-20.
Resolved Problems in CMW520-B1202
RTD09176
Description: The call will fail.
Condition: Keeping on changing R2 country mode for a long time.
RTD09518
Description: The default value of dl-bits will not be renewed.
Condition: While configuring R2 CAS, if you execute follow commands in order: renew
0011, reverse 0101, undo renew, and undo reverse.
RTD07543
Description: That will result in the configuration of ATM-CLASS under this interface
invalid.
Condition: If you apply global ATM-CLASS under ATM interface, and configure
ATM-MAP under this interface‘s ATM-PVC view, then delete the ATM-MAP.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
41/91
40
RTD09212
Description: The FTP server function on NAT can not work.
Condition: Configuring the IP address of WAN on the LAN server equaling to the
address of NAT‘ interface.
RTD10006
Description: The system will hint ‗Unable to open file‘.
Condition: The router is configured as TFTP client and PC as server . The user configures
a source file name with memory path.
RTD09918
Description: The default routing can not be deleted immediately.
Condition: Ripng default-route has been configured. The user deletes this
configuration and displays the routing information of Ripng.
RTD09832
Description: The voice bandwidth will loss and the call can not success.
Condition: If you configuring sequentially voice bandwidth and cir with equal value,
and then saving it and rebooting the router.
Resolved Problems in CMW520-B1106
RTD09261
Description: After you input display mpls te cspf tedb node, the router will reboot.
Condition: Input command display mpls te cspf tedb node.
RTD08380
Description: When configuring ATM CLASS UBR on ATM-CLASS, if the parameter has
excess length, the parameter can work actually and the router will print abnormal info
and then reboot.
Condition: Input a parameter with excess length on the ATM service.
RTD08839
Description: Can not get correct statistic of some FTP packets.
Condition: Apply QoS on one port and match FTP packets, and then run DAR statistic.
RTD08764
Description: This port can not learn MAC address with learning state.
Condition: Enable STP and keeping one bridge port with learning state, and send
packets with different source MAC address to this port.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
42/91
41
RTD08536
Description: The virtual VRRP MAC address can not be loaded on this port‘s MAC table
and then cause packets with it can not be transferred.
Condition: when the MAC tables is full on one port, and then apply VRP on it.
RTD08326
Description: VT‘s state will change up and down repeatedly.
Condition: Apply MPoFR on a 4E1 board, and transferring 10M speed data on it.
RTD06971
Condition: Configure DHCP under the interface view, and then change the
interface‘s IP address.
Description: All the configuration of DHCP on this interface wil l be lost.
Related Documentation
New Feature Documentation
None.
Documentation SetH3C MSR 20 Series Routers Installation Manual
H3C MSR 30 Series Routers Installation Manual
H3C MSR 50 Series Routers Installation Manual
H3C MSR Series Routers Configuration Guide
H3C MSR Series Routers Command Reference
H3C MSR Series Routers Interface Card and Interface Module Manual
H3C MSR Series Routers OAP Module Manual
H3C MSR 20-1X Routers Installation Manual
H3C MSR Series Routers Web-Based Configuration Manual
H3C MSR 20-1X Routers Quick Start
H3C MSR 30-1X Routers Quick Start
H3C MSR 900 Series Routers Installation Manual
Obtaining DocumentationTake the following steps to get related documents from the H3C website at www.h3c.com.
1. Go to http://www.h3c.com/portal/Technical_Documents.
-
8/20/2019 Procedimento de Configuração de Roteadores HP
43/91
42
2. Choose the desired product category and model.
Technical support
http://www.h3c.com
-
8/20/2019 Procedimento de Configuração de Roteadores HP
44/91
43
Appendix A Feature List
Hardware FeaturesTable 5 MSR20-1X Series Hardware Features
ItemMSR 20-10Description
MSR 20-11Description
MSR 20-12Description
MSR 20-13Description
MSR 20-15Description
Dimensions (H x W
x D)
44.2mm300
mm240mm
44.2mm300
mm240mm
44.2mm300
mm240mm
44.2mm300
mm240mm
44.2mm300
mm240mm
Weight 3Kg 3Kg 3Kg 3Kg 3Kg
Input AC voltage
Rated voltage: 100 VAC to 240 VAC;
50 Hz/60 Hz
Input DC voltage Not support DC
Max power 25W
Operating
temperature0°C to 40°C
Relative humidity
(noncondensing)5% to 90%
Processor PowerPC PowerPC PowerPC PowerPC PowerPC
BootROM 1MB 1MB 1MB 1MB 1MB
FLASH 16MB/32 MB 16MB/32 MB 16MB/32 MB 16MB/32 MB 16MB/32 MB
Memory 256MB 256MB 256MB 256MB 256MB
Externa
l
modul
e
SIC/
DSIC
module
1 1 1 1 1
Internal
modul
e
VPM
strip0 0 1 0 1
Fixed
interfa
ce
Consol
e/AUX1 1 1 1 1
USB 1 1 1 1 1
FE1 electrical
interfaces
1 electrical
interfaces
1 electrical
interfaces
1 electrical
interfaces
1 electrical
interfaces
FE
switchi
ng
interfac
e
4 4 4 4 4
ADSL 0 0 0 0 1
G.SHDS 0 0 0 1(G.SHDSL.bis 0
-
8/20/2019 Procedimento de Configuração de Roteadores HP
45/91
44
L )
SAE 0 1 0 0 0
ISDN
S/T0 0 0 1 1
AM 0 0 0 0 1
E1/T1 0 0 1 0 0
option
alWlan 1 0 1 1 1
Table 6 MSR20 Series Hardware Features
ItemMSR 20-20Description
MSR 20-21Description
MSR 20-40Description
Dimensions (H x W x
D)
44.2mm360mm287.
1mm
44.2mm360mm28
7.1mm
44.2mm442mm407.1
mm
Weight 3.4Kg 3.4Kg 5.4Kg
Input AC voltage Rated voltage: 100 VAC to 240 VAC; 50/60 Hz
Input DC vo