processing and fabrication of advanced materials … sessions schedule.… · boron carbide metal...

P F A M - X X I I I

23rd International Conference on

Processing and Fabrication of

Advanced Materials

(PFAM-XXIII)

December 5 to December 7, 2014

Technical sessions schedule

Department of Mechanical and Industrial Engineering

Indian Institute of Technology, Roorkee, India

P F A M - X X I I I

Session A1: Metal Matrix Composites

Time: 14.00 - 15.30

Venue: Room No. 348 1 PFAM 129 Machinability issues in aluminum matrix composites

M.K. Gupta, P.K. Rakesh

2 PFAM 146 A Study on Fabrication of Hybrid Mg/ (Al2O3p+SiCp+Grp) Composite utilized Fabricated Gas Injection Magnesium Melting Set Up

J. Hira, A. Manna, S.K. Mangal

3 PFAM 159 Investigation of Mechanical Properties of LM 25 Aluminum Alloy - Alumina - Boron Carbide Metal Matrix Composites.

M. Jaivignesh, B.V. Ramnath

4 PFAM 244 Sintering Studies of Structural Ceramics

Vikas Verma, B. V. Manoj Kumar

5 PFAM 277 Tribological Characterization and Parameters Optimization of Al6061Hybrid Metal Matrix Composites

M.Kumar A.Megalingam Murugan, V.Baskaran, K.S.Hanumanth Ramji

6 PFAM 254 C/ZrC-SiC composite derived from Zirconoborosiloxane-polycarbosilane blend

Anurag Kamal, Anil Painuly, L R Remya, P V Prabhakaran and S Packirisamy

Session B1: Advanced Manufacturing I

Time: 14.00 - 15.30

Venue: Room No. 254 1 PFAM 124 A fuzzy logic approach in prediction of responses while finishing microchannels

using abrasive flow machining

G. Venkatesh, Tarlochan Singh, Apurbba Kumar Sharma, Akshay Dvivedi

2 PFAM 128 Defect Investigation in Microwave Drilling of Perspex at 2.45 GHz

Nitin Kumar Lautre, Apurbba Kumar Sharma, Pradeep Kumar and Shantanu Das.

3 PFAM 133 Influence of post clad heat treatment of WC based composite microwave clad

S. Zafar, A.K. Sharma

4 PFAM 153 Application of hybrid fuzzy expert system to predict the quality of laser beam machined surface

G. Sharma, V. Kumar

5 PFAM 226 Twinning induced plasticity steel - a promising material for automobile industry and structural application

Dinesh Kumar

6 PFAM 319 Application of Rapid Prototyping in Biomedical field: A review

Deepen Banoriya, R. K. Dwivedi and Rajesh Purohit

DAY 1: DECEMBER 05, 2014 TECHNICAL SESSION - I

P F A M - X X I I I

Session C1: Nano Composites I

Time: 14.00 - 15.30

Venue: Room No. 251 1 PFAM 148 Synthesis of CNTs by arcing process without catalyst

S.K. Chaudhary, K.K. Singh, R. Venugopal

2 PFAM 157 Synthesis and characterization of microcrystalline silicon carbide thin films for high temperature applications

Umesh Rizal, Bhabani S. Swain, Deepak Pattanayak, Bibhu P. Swain

3 PFAM 163 Structural and photo-conducting properties of CdSe-PVA nanocomposite films

S. Pokhriyal, S. Biswas

4 PFAM 214 Anisotropic growth of palladium nanocrystals by laser ablation

M.P. Navas, R.K. Soni

5 PFAM 256 Effects of titanium dioxide and titanium diboride nanoparticulates on room temperature tensile response of pure magnesium

Ganesh Kumar Meenashisundaram, T. S. Srivatsan, AbdulhakimAlmajid and Manoj Gupta

6 PFAM 266 Micropattern diamond-like nanocomposite (DLN) thin film for cell adhesion

T.S.Santra, S.Devgan, S.Kar, T.K. Bhattacharyya, F.G.Tseng

Session A2: Polymer Matrix Composites I

Time: 16.00 - 17.30

Venue: Room No. 348 1 PFAM 315 Evaluation of weight fraction on tensile strength and modulus of waste ground

nut shell reinforced polyester composite

M.N. Prabhakar, Atta ur Rehaman, Jung Il Song

2 PFAM 209 Surface treatment of natural fibers in bio-composites: A review

A.K. Rajput, A. Soni, P.K. Bajpai

3 PFAM 115 Friction and dry sliding wear behavior of Meta cresol novalac epoxy composites filled with microsized Al2O3 particulates

S.R. Chauhan, K. Dass, B. Gaur

4 PFAM 311 Control of torque during drilling in composite laminates

Amrinder Pal Singh, Manu Sharma, Inderdeep Singh

5 PFAM 261 Study of Delamination and Surface Roughness in the Milling of MWCNT Based GFRP Nanocomposite

Dhiraj Kumar & Dr. K. K. Singh

6 PFAM 235 A review of adhesives in the manufacturing of biocomposite used in construction

Tanya Buddi, Nitin Muttil, B Nageswara Rao and Swadesh Kumar Singh

DAY 1: DECEMBER 05, 2014 TECHNICAL SESSION - II

P F A M - X X I I I

Session B2: Advanced Manufacturing II

Time: 16.00 - 17.30

Venue: Room No. 254 1 PFAM 166 Micro-cracks and spatter free controlled grooving of silicon with water-jet

assisted fiber laser beam

Y.K. Madhukar, S. Mullick, A. Prashant, A.K. Nath

2 PFAM 168 Investigation on 3D laser forming of AISI 304 sheet using coupling and upsetting mechanisms

S.S. Chakraborty, R. Kataruka, Y.K. Madhukar, V. Racherla, A.K. Nath

3 PFAM 169 Analysis of surface finish and material removal rate using response surface methodology for magnetic abrasive finishing of cylindrical tubes

P. Singh, L. Singh, S. Singh

4 PFAM 173 Microstructural characterization of microwave composite cladding on mild steel

A. Bansal, A.K. Sharma, P. Kumar

5 PFAM 177 Experimental Investigation of EDD on Hybrid Metal Matrix Composite

Abhishek Singh, Sabindra Kachhap, Ravinder Kumar

6 PFAM 293 Application of magnetically assisted gel abrasives for fine finishing

Parminderjeet Singh, Sehijpal Singh ,Lakhvir Singh

Session C2: Nano Composites II

Time: 16.00 - 17.30

Venue: Room No. 251 1 PFAM 318 Recent advances in polymer based nano composite materials for mechanical

and electronic applications

Sunil Kumar, M. M. Malik and Rajesh Purohit

2 PFAM 309 Martensitic phase transformation and magnetocaloric effect in magnetron sputtered Ni50Mn37Sb13 heusler alloy thin film

Harish Sharma Akkera, Inderdeep Singh, Davinder Kaur

3 PFAM 102 Promoting alloying of cryomilled nanostructured Titanium, Niobium, Tantalum, Zirconium powders using spark plasma sintering and high pressure torsion

Zhiming Li, Yitian Wang, Baolong Zheng, Yizhang Zhou, T.S. Srivatsan, Ruslan Z. Valiev and Enrique J. Lavernia

4 PFAM 284 Surfactant free preparation of biomagnetic iron- oxide hydroxyapatite nanoparticles for hyperthermia therapy

M. Sneha, N. Meenakshi Sundaram

5 PFAM 312 Effect of Heat Treatment on Mechanical Properties of Aluminium Alloy Based Nano Composites-A Review

Dinesh Kumar Koli, Geeta Agnihotri and Rajesh Purohit

6 PFAM 233 Study the Effect of Temperature on the Properties of ASS-304 Using ANN

Lakshmi Kanumuri, D V Pushpalatha, Amit Kumar Gupta, Swadesh Kumar Singh

P F A M - X X I I I

Session A3: Polymer Matrix Composites II

Time: 11.00 - 13.30

Venue: Room No. 348 1 PFAM 167 Modelling and simulation of glass/ epoxy composite layup for hydrogen fuel cell

powered vehicle’s body

Brajesh Tripathi, Ajay Kumar, Sachin Mishra, Pradeep Kumar

2 PFAM 303 Effect of Calcination Temperature on Quality of Hydroxyapatite that Fabricated from Fish Scales Biowaste

Y. Chittara, A. Yadav, M. Ravi Sankar, Arbind Prasad, B. N Mondal, N Mondal, U. Batra

3 PFAM 260 Thermal and Crystalline behavior of injection moulded bagasse fiber reinforced Polypropylene

Manish Kumar Lila, Saurabh Chaitanya, Inderdeep Singh

4 PFAM 314 Review of Thermal Conductive Behaviour of Polymer-Carbon Nanotube Composites

Saurav Gairola, Amrinder Pal Singh, Prashant Jindal

5 PFAM 136 Mechanical behavior of drilled glass fiber reinforced plastic laminates

P.K. Rakesh

6 PFAM 280 Three dimensional finite element modeling and simulation of curvilinear thin-wall machining of aluminum 7075-T6 alloy

Gururaj Bolar, S. N. Joshi

Session B3: Advanced Manufacturing III

Time: 11.30 - 13.00

Venue: Room No. 254 1 PFAM 219 A Study on the Micro Tool dressing using Ultrasonic Vibration in-process Grinding

Vivek Jain, Apurbba Kumar Sharma, Pradeep Kumar

2 PFAM 252 Impact of Pulse Width on Hole Overcut in an Electrochemical Discharge Machining of Blind Holes

Pankaj Kumar Gupta, Akshay Dvivedi, Pradeep Kumar

3 PFAM 253 Study of The Near-dry Electric Discharge Machining

Krishnakant Dhakar, Akshay Dvivedi

4 PFAM 257 Electrophoretic Deposition of TiO2-Ag Photoelectrode for the Application in Dye Sensitized Solar cells

Swati Bhardwaj, Arnab Pal, Papia Chowdhury, Kuntal Chatterjee, Subhayan Biswas

5 PFAM 229 Design of Self Compensated Non Contact Type Capacitive Sensor for Liquid Level Control with enhanced sensitivity - A Novel Approach

C.S. Suresh Babu, P. Manohar

6 PFAM 321 Study of CNT particle based abrasive media used for finishing work piece by abrasive flow machining

Himmat, R.S.Walia, Qasim Murtaza, Sachin Dhull

DAY 2: DECEMBER 06, 2014 TECHNICAL SESSION - III

P F A M - X X I I I

Session C3: Welding Technology I

Time: 11.30 - 13.00

Venue: Room No. 251 1 PFAM 116 Experimental investigation of friction stir spot welding of aluminum 6061 using

Taguchi’s methodology

S. Singh, V. Bhatti, Lokesh Dahiya

2 PFAM 119 Effect of process parameters and cooling media on mechanical properties of friction stir welded 1060 aluminium alloy

Deepti Jaiswal, Ratnesh Kumar Raj Singh, Sunil Pandey, Rajesh Prasad

3 PFAM 120 Friction stir welding of nuclear grade dissimilar steels

Ratnesh Kumar Raj Singh, Dinesh Rathod, Sunil Pandey, Rajesh Prasad

4 PFAM 140 Effect of different post weld heat treatments on the mechanical properties of Cr-Mo boiler steel welded with SMAW process

S.R. Ahmed, Late A. Agarwal, B.S.S. Daniel

5 PFAM 156 Study of friction stir welded joint for AA6061 aluminium alloy material using altair hyperweld

K.S. Mehra, S.Singh, R.Kumar

6 PFAM 296 Corrosion behaviour of weldments: A review

Mohd Azeem, Mukesh Bhardwaj

Session A4: Polymer Matrix Composites III

Time: 14.00 - 15.30

Venue: Room No. 348 1 PFAM 143 Predictive modeling of drilling induced damage in composite laminates using

fuzzy logic

V. Dhawan, S. Singh, K. Debnath, S. Wadhawan

2 PFAM 149 Synthesis and characterization studies in natural fiber / lignite fly ash reinforced geopolymer composites

Sathish Kumar G K, Umapathy.M.J, Vivekanandhan.P, Karthikeyan.S

3 PFAM 198 Sliding Behavior of Jute Fabric Reinforced Polypropylene Composite

Temesgen Berhanu Yallew, Pradeep Kumar, Inderdeep Singh

4 PFAM 199 Drilling of natural fiber reinforced thermoplastic composites

P.K. Bajpai

5 PFAM 187 Experimental investigations of thrust force and delamination in conventional and modulation assisted drilling of glass fibre reinforced plastics

R.S. Joshi, H. Singh, I. Singh

6 PFAM 317 Mechanical and Morphological Characterization of Short Kenaf Fiber Reinforced Polypropylene Composites

Saurabh Chaitanya, Inderdeep Singh

DAY 2: DECEMBER 06, 2014 TECHNICAL SESSION - IV

P F A M - X X I I I

Session B4: Advanced Manufacturing IV

Time: 14.00 - 15.30

Venue: Room No. 254 1 PFAM 301 X-ray absorption spectroscopy of yttria stabilized zirconia nanoparticles generated

by laser evaporation method: Effect of mode of laser operation

J. Khare, P. Rajput, M. P. Joshi, S. N. Jha, D. Bhattacharyya and L. M. Kukreja

2 PFAM 295 Investigation on Recast Layer Thickness and Hardness of EDM Processed Al-7075 Metal Matrix Composite

Rajesha S., Radha Raman Mishra and Apurbba Kumar Sharma

3 PFAM 306 Novel production method of porous surface coating on titanium alloy sample for orthopedic application

Ashwin Patel, Naresh Bhatnagar

4 PFAM 320 Study and prediction of surface finish of external cylindrical surfaces of titanium alloys by electro chemical honing (ECH) process

P. Sudhakar Rao, D. K. Dwivedi, P. K. Jain

5 PFAM 290 Effect of Process Parameters of Near-dry EDM on Machining of a Conductive Material

Pankhuri Arora, Krishnakant Dhakar, Akshay Dvivedi

6 PFAM 227 Parameter Optimisation of Nd:YAG Laser Welding for Aluminium with SiC MMC

A.J. Banerjee, M.K. Biswal, A.K. Das, H. Chattopahyaya, A.K. Lohar

Session C4: Welding Technology II

Time: 14.00 - 15.30

Venue: Room No. 251 1 PFAM 171 Mechanical properties and microstructural characteristics of friction stir welded

dissimilar AA5052H32 aluminium alloy and IRSM42-93 micro alloy steel butt joints

K.K. Ramachandran, N. Murugan, S. Shashi Kumar, Pradeep Johnson

2 PFAM 181 Friction stir welding of 316 L austenitic stainless steel-microstructure and mechanical properties

S. Shashi Kumar, N. Murugan, K.K. Ramachandran, P. Johnson

3 PFAM 206 Effect of chromium content on tribological properties of weld surfacings

Yogesh Kumar Singla, D. K. Dwivedi, N. Arora

4 PFAM 272 Study of FSW of thin ferrous alloys sheets

Amandeep singh, D. Venkateshwarlu, M. M. Mahapatra and Pradeep Kumar

5 PFAM 126 Friction Stir Welding Characteristics of In-Situ Al-4.5%Cu-TiC Composites

Anand Kumar, P. K. Jha, M. M. Mahapatra

6 PFAM 285 Effect of Tool Geometry and RPM on Tensile Properties of Friction Stir Welded Aluminium Joints

Biswajit Parida and Sukhomay Pal

P F A M - X X I I I

Session A5: Characterization of Materials I

Time: 16.00 - 17.30

Venue: Room No. 348 1 PFAM 161 Effect of process parameters on the tensile strength and microstructure of

microplasma arc welded SS 316L stainless steel sheets)

Srikant Prasad, S. Pal, and P. S. Robi

2 PFAM 178 Thermal characterization of phase change materials used for thermal energy storage in solar thermal power plants

Hakeem Niyas, Ankit Kumar Shukla and P. Muthukumar*

3 PFAM 197 Effect of cooling on microstructure and mechanical properties of friction stir processed surface composites

Vipin Sharma, U. Praksh, B. V. Manoj Kumar

4 PFAM 228 Microstructural characterization of EWAC+20%WC102Ni microwave cladding on mild steel substrate

Akshay Pathania, Dheeraj Gupta, Vivek Jain

5 PFAM 283 Incomplete Transformation Characteristics of Aged NiTi shape Memory Alloys

K Hari Krishnan, D. Lenin Singaravelu, P S Misra, K Chandra ,Vinod S.Agarwala

6 PFAM 255 Ball Milled (Titanium plus Nickel) Additions to Enhance Compressive Response of Pure Magnesium

S. Sankaranarayanan , Harish Menon, T. S. Srivatsan, A. Almajid, M. Gupta

Session B5: Manufacturing Process I

Time: 16.00 - 17.30

Venue: Room No. 254 1 PFAM 105 Development of a pattern making method for strain measurement on

microstructural level in ferritic cast iron

Keivan A. Kasvayee, Lennart Elmquist, Anders E. W. Jarfors, Ehsan Ghassemali

2 PFAM 182 Effect of T6 heat treatment in mechanical and tribological properties of A356 aluminum alloy fabricated by gravity, vacuum and squeeze casting.

K. Sekar, Allesu K., M.A. Joseph

3 PFAM 316 Stir Casting & GTAW-Welding of Aluminum Metal Matrix Composite: Review

Vivek Singh Shekhawat, Deepak Mehra, Neeraj Kumar Sharma

4 PFAM 298 Parameters Effecting Slurry Erosion of Various Metals: A Review

Saim Abbas, Shravan kumar

5 PFAM 222 Mg alloy: machining requirements & its experimental evaluation

D.K. Misra, A.K. Singh, A.B. Khare, J.K. Bajpai

6 PFAM 223 INVAR: Machining and its usage in opto-mechanical system

D.K. Misra, H. Singh, A.B. Khare, J.K. Bajpai

DAY 2: DECEMBER 06, 2014 TECHNICAL SESSION - V

P F A M - X X I I I

Session C5: Advanced Materials

Time: 16.00 - 17.30

Venue: Room No. 251 1 PFAM 170 Application of CIGS chalcopyrite semiconductors in solar cells

V. Agarwal, G. Arora

2 PFAM 282 Stress analysis of Micro-lattice structures under Uni-axial loading

Siva Krishna Indurthi, Sanjay K. Darvekar

3 PFAM 138 A Review on Failure of HSLA Steel Welds in Oil and Gas Pipelines

S. Sharma, S. Maheshwari

4 PFAM 241 Microstructural and mechanical behavior of multiaxially cryoforged Al 5080 alloy

Neetu, R. Jayaganthan

5 PFAM 108 Properties of green concrete for sustainable construction

Didier Talamona, Tan Kang Hai

6 PFAM 110 Flexible, high strength, copper conductors for flexible electronic circuits

A. Hussain, M.M. Hussain

Session A6: Characterization of Materials II

Time: 09.30 - 10.45

Venue: Room No. 348 1 PFAM 248 Development and microstructural characterization of microwave cladding on high

speed steel [SS-304]

Ajit M Hebbale, Shrinath M S

2 PFAM 135 Surface and mechanical characterization of polyurethane coated Al-Mg-Si alloy using thermal spraying coating technique for aircraft applications

R.B. Durairaj, S. Ramachandran, S. Ruban, B. Mohanty

3 PFAM 267 Effect of soaking temperature and time on microstructure and mechanical properties of P91 steel

C. Pandey, M.M. Mahapatra

4 PFAM 273 Feasibility study on friction surfaced composite cladding of die steel- Cr3C2-25 NiCr

Ravi Prakash Yadav, D. Venkateswarlu, M. M. Mahapatra, R. S. Mulik, R. Jayaganthan

5 PFAM 288 Enhanced Environmental Resistance of Structural Concrete through use of Advanced Materials

Anil Patnaik, Srikanth Bajaj, Mohammed Khan and T. S. Srivatsan

DAY 3: DECEMBER 07, 2014 TECHNICAL SESSION - VI

P F A M - X X I I I

Session B6: Manufacturing Process II

Time: 09.30 - 10.45

Venue: Room No. 254 1 PFAM 139 Experimental evaluation of deep drawability of adhesive bonded steel sheets

V. Satheeshkumar, R. Ganesh Narayanan

2 PFAM 150 Comparison of deforming forces for deformation machined components with conventionally formed components

Arshpreet Singh, Anupam Agrawal

3 PFAM 196 Formability analysis in multistage forming of anisotropy sheet metal

K. Bandyopadhyay, S.K. Panda, P. Saha

4 PFAM 155 Parametric optimization of helical abrasive flow machine by Taguchi and ANN

Suman Kant, Achitanand Dubey, Lalit Ahuja

5 PFAM 234 Experimental and numerical studies of warm formability for Ti-6Al-4V alloy

Nitin Kotkunde, Amit Kumar Gupta, Swadesh Kumar Singh

Session C6: Modeling and Simulation I

Time: 09.30 - 10.45

Venue: Room No. 251 1 PFAM 154 The effect of outlet positions on intermixing during grade transition in six strand

billet caster tundish

Suman Kant, Achitanand Dubey, Shalom Akhai

2 PFAM 215 Optimisation of process parameters in high pressure die casting using simulation

Arunkumar Y, Srinath M S, Sree Rajendra, Roopa R

3 PFAM 216 Simulation and analysis of process parameters in closed die forging

Sree Rajendra, Arunkumar Y, Srinath M S, Harshavani M D

4 PFAM 268 Material for Energy harvesting from Ambient Vibration: A literature Review

Prakash Kumar, Dr. Anil Kumar

5 PFAM 297 Studies on simulated Single Pass HAZ thermal cycles in 18 mm thick Micro Alloyed steel Plate

Sanjeev Kumar, S. K. Nath

Session D6: Miscellaneous

Time: 09.30 - 10.45

Venue: Room No. 252 1 PFAM 291 Natural Fibre Composites Mechanical Properties Improvement: A Review

Dharmender, Navdeep Malhotra, V.P. Dutta

2 PFAM 322 Modeling inclusion floatation in tundish to produce clean steel

Rajeev Kumar Singh, Saikat De, Sujata Devi, Basudev Mishra, Ramen Datta

3 PFAM 299 Numerical investigation of grade intermixing and heat transfer during ladle change-over in steelmaking tundish

Md Irfanul Haque Siddiqui, Pradeep Kumar Jha

4 PFAM 270 Heat transfer analysis of ferric oxide nano fluid in parallel tube counter flow heat exchanger

Raakesh,M., Purusothaman, D., Sachin Kumar, R. and Sabarinathan, S.

5 PFAM 308 Study of inclusion removal in a single strand tundish with varying dam height and position

Ambrish Maurya and P. K. Jha

P F A M - X X I I I

Session A7: Characterization of Materials III

Time: 11.15 - 12.30

Venue: Room No. 348 1 PFAM 307 Effect of Tribo-oxide Layers on the Sliding Wear Behaviour of Rutile reinforced

LM13 Alloy Composites at High Temperature and Pressure

Rama Arora, Anju Sharma, Suresh Kumar, Gurmel Singh and O.P. Pandey

2 PFAM 310 Effect of power ultrasound on solidification of Al-Cu alloys with different solute concentrations

Neeraj Srivastava and G.P. Chaudhari

3 PFAM 101 Influence of Scandium and Zirconium on Mechanical Behavior of Cryomilled Aluminum-Magnesium Alloys

T.D. Topping, T.J. Harrell, T. Hu, J.M. Schoenung E.J. Lavernia and T. S. Srivatsan

4 PFAM 302 Synthesis and Designing of Conducting Polypyrrole / Fly Ash/ Ferrofluid composite for Microwave Absorption Application

Swati Varshney, V.K. Jain, S. K. Dhawan and V.P. Dutta

5 PFAM 221 Investigation of influence of process parameters over the mechanical properties of friction stir welded Al2O3 and SiC reinforced hybrid aluminium composite joints

C.Venkatesh, M.Aravindh, G.Karthikeyan, K.M.Sridharan, G.Eswaramuruthy

Session B7: Manufacturing Process III

Time: 11.15 - 12.30

Venue: Room No. 254 1 PFAM 249 Investigation of Creep Deformation of 25Cr35NiNb Microalloyed Reformer Steel

Tube Material

AmitavaGhatak and P.S. Robi

2 PFAM 250 Artificial neural network modeling of High Temperature Deformation of Al-Cu-Mg Alloys Micro-Alloyed with Silver

Purnendu Kumar Mandal1and P S Robi2

3 PFAM 251 Study on thickness variation during super plastic forming of Friction Stir Processed Al -5086 Alloy

Vivek Kumar, Raja Allavikutty, Vivek Pancholi

4 PFAM 304 Effect of Heat Treatment on Mechanical Properties of 16Cr-5Ni-Mo Martensitic Stainless Steel

Amarendra H. J.a, G.P. Chaudharib, S.K. Nathc

DAY 3: DECEMBER 07, 2014 TECHNICAL SESSION - VII

P F A M - X X I I I

Session C7: Modeling and Simulation II

Time: 11.15 - 12.30

Venue: Room No. 251 1 PFAM 300 Study of grade intermixing and heat transfer in two different shapes of tundishes

Waseem Ahmad, Md Irfanul Haque Siddiqui, Pradeep Kumar Jha

2 PFAM 142 Finite element modeling of burr formation in orthogonal cutting of glass fibre reinforced polymer composites

Parul Jayant, K. K. Singh

3 PFAM 292 Simulation of void elimination from vacuum enhanced resin infusion technology (VERITy) laminates during external consolidation

Ajay Kumar, Mukul Shukla

4 PFAM 271 Study on effect of tool shoulder geometry on thermal distribution in friction stir welding of magnesium alloy.

AkanshaYadav, D. Venkateshwarlu, M. M. Mahapatra, P. K. Jha

5 PFAM 160 Compare various parameters between lathe turning and swansoft CNC simulator

Surinder Pal

Keynote Lectures

1. Influence of additives on the mechanical and flammability properties of kenaf-polypropylene composites

J. Pius, R. J. D’Souza, A. A. Somashekar and D. Bhattacharyya 2. Characterization of shrinkage porosity in spheroidal graphite cast iron components

Kaisu Soivio, Lennart Elmquist, Anders E.W. Jarfors

*Other keynote lectures will be made online available soon.

Note: If you do not find your manuscript in oral presentations then please write to us at [email protected]

processing and fabrication of advanced materials … sessions schedule.… · boron carbide metal...

Documents