product datasheet tyra series - mouser electronicsc11395-tyra-m tyra reflector mp-l metal 40 mm 23.1...
TRANSCRIPT
PRODUCT DATASHEETTyra series
Ordering numberDescription
FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus
C11394C11394-Tyra-S
TyraReflectorMP-LMetal40 mm23.1 mmRound PC - Pin, glue Ready
FWHMEfficiencycd/lmGerber File
20 degrees - - Available
Used with Tyco holder
Ordering numberDescription
FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus
C11395C11395-Tyra-M
TyraReflectorMP-LMetal40 mm23.1 mmRound PC - Pin, glue Ready
FWHMEfficiencycd/lmGerber File
32 degrees - - Available
Used with Tyco holder
Ordering numberDescription
FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus
C11396C11396-Tyra-W
TyraReflectorMP-LMetal40 mm23.1 mmRound PC - Pin, glue Ready
FWHMEfficiencycd/lmGerber File
52 degrees - - Available
Used with Tyco holder
NOTE: The typical divergence will be changed by different color, chip size and chip positiontolerance. The typical total divergence is the full angle measured where the luminous intensityis half of the peak value.
November 22nd 2011 0:03 Copyright Ledil Oy - Subject to change without prior notice - Page 1/3
Ledil Oy Salorankatu 10 24240 SALOFinland
http://www.ledil.com email: [email protected] FAX: +358-2-733 8001
PRODUCT DATASHEETTyra series
GENERAL INFORMATION
- Product series especially designed & optimized for MP-L series of LEDs. - Special care taken to make light distribution as uniform as possible.- Reflector is made of aluminium coated PC (120 degrees of Celcius / 248 degrees of Fahrenheit) withprotective lacquer (110 degrees of Celcius / 230 degrees of Fahrenheit).
- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glueoptions.http://www.ledil.com/datasheets/DataSheet_GLUES.pdf
NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the endproduct. For example, mechanical stress, vibration and holes on the surface of the circuit boarweaken the strength of the glue.
NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. Ifcleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LEDmanufacturer -this is important as cleaning shall under no circumstances damage LEDs or otherelectronics components on the PCB.
Further note that optical components shall not be cleaned with any chemicals - only micro fibercloth may be used to remove fingerprints or other traces from handling.
November 22nd 2011 0:03 Copyright Ledil Oy - Subject to change without prior notice - Page 2/3
Ledil Oy Salorankatu 10 24240 SALOFinland
http://www.ledil.com email: [email protected] FAX: +358-2-733 8001
PRODUCT DATASHEETTyra series
C11394 C11396
November 22nd 2011 0:03 Copyright Ledil Oy - Subject to change without prior notice - Page 3/3
Ledil Oy Salorankatu 10 24240 SALOFinland
http://www.ledil.com email: [email protected] FAX: +358-2-733 8001
AD
BC AD
32
3
2
41
4
1
DESIGNED BYol
DATE07.07.2010
CHECKED BY DATE
DRAWN BY DATE
This drawing is our property.It can't be reproducedor communicated withoutour written agreement.
SCALE 2:1 WEIGHT(g) SHEET 1/1
SIZE
A4DRAWING NUMBER REV
DRAWING TITLE
Datasheet Tyra series
Material: PCMetal coating with laquering
Ledil OyTehdaskatu 13FIN-24100 SALOFinland
sn
ah 25.7.2011
25.7.2011 3
Front viewScale: 1:1
23.07
2.25
Bottom viewScale: 1:1
1.2
11
20.53
Top viewScale: 1:1
40.0
1
11.2
Isometric viewScale: 1:1