product reference guide - s3. · pdf fileg i n e e r i n g t h a t ... 1 6 20" 10'...

Cablofil/Legrand

Phone 800-658-4641

618-566-3230

Fax 618-566-3250

8319 State Route 4

Mascoutah, IL USA 62258

www.cablofil.com

Pass & Seymour/Legrand

Phone 800-611-7277

Fax 800-223-4196

P.O. Box 4822

Syracuse, NY USA 13221-4822

www.passandseymour.com

Southwire

Phone 800-444-1700

Fax 770-838-6501

One Southwire Drive

Carrollton, GA USA 30119

www.southwire.com

www.ve-plus.com

Value engineering that’s guaranteed!

PRODUCT REFERENCE GUIDE

ranteed!Value engineering that s guarengineering that’s guar

Copyright © 2007 VE Plus, Printed in U.S.A. VEP•002•7/07

Today’s market demands that you deliver quality

installations with the best products available. That’s

why these industry-leading names in the electrical

industry have joined forces to increase your produc-

tivity and profitability with the VE PlusTM program. Our

studies show that you can save up to 30% on your

next commercial installation by using MC cable

from Southwire supported by Cablofil cable tray with

PlugTail devices from Pass & Seymour/Legrand

instead of conduit and pulled wire.

We’re so sure of your cost savings,

VE PlusTM

will guarantee it.

P&S PlugTail. Proven to be the fastest,

most reliable wiring device installation

for any commercial job.

At rough-in, install the pre-stripped leads of a P&S PlugTail

connector instead of pigtails. At device installation, click in the

connector and tighten the mounting screws – done in less than

a minute.

P&S PlugTail installation is three times faster than conven-

tional device installation. With no exposed terminals, you can

power-up and test a circuit at any time once the connectors

are installed. And because PlugTail delivers dependability,

quality and easier, safer service for years to come, your

customers benefit, too.

Southwire innovations help you gain

a competitive edge on every job.

UL® listed and NEC® compliant, this innovative new Type MC

cable can be used anywhere Type MC or AC cable are permit-

ted. The difference is Southwire's patented design. MCAP,

All-Purpose MC, can speed branch circuit make-up by up to

30 percent by eliminating separate ground-wire terminations.

HCF MCAP™ - the version for health care, can increase installa-

tion productivity by eliminating the need for anti-short bushings,

the need to remove the paper covering from each conductor

and can reduce securing and supporting requirements, while

providing a 350% better ground path connection. Eliminate the

most labor-intensive and costly aspect of wiring — ground

make-up inside the box, light fixture and panel.

Alumaflex™, with triple e™ aluminum alloy, feeder size MC

cable is a more flexible, light-weight and lower cost material

option to traditional pipe and wire in conduit. Pre-assembled,

factory-tested cable with color coded conductors and oversize

grounds mean a safer, easier and faster installation without

the risk of damage to conductors from pulling into conduit.

Available sizes range from 6 AWG to 900 kcmil. Switching to

aluminum MC feeder cable can reduce total installation costs

up to 50%.

Cablofil/Legrand – the world

leader in cable tray

MCAP™ cable supported by Cablofil wire tray

creates an installation that is neat and orderly

in appearance and installs faster than traditional

MC support methods. It’s capable of supporting

large number of cables in a single pathway

and the ventilated design of Cablofil tray keeps

cables cool — so no derating of cables is

required by the NEC.

An innovative

idea from the

best brands in the business!

1wwwwww..vvee--pplluuss..ccoomm

2 Cablofil's Optimized Wire Size, Tray Patent Number - 6.138.961. wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444

3wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444

PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES

QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE

CVN 50 3 – 2" 3.3' 2.6 629 050 629 053 - 629 054 941 332 934 071

CVN 100 3 – 4" 3.3' 4.6 629 100 629 103 - 629 104 941 333 934 073

CVN 150 3 – 6" 3.3' 7.3 629 150 629 153 - 629 154 941 334 934 075

CVN 200 3 – 8" 3.3' 9.3 629 200 629 203 - 629 204 941 335 934 077

CVN 300 3 – 12" 3.3' 13.2 629 300 629 303 - 926 304 941 336 934 079

CVN 450 3 – 18" 3.3' 22.5 629 450 629 453 - ** 941 338 934 083

CVN 500 3 – 20" 3.3' 28.4 629 500 629 503 - 629 504 941 339 934 085

CVN 600 3 – 24" 3.3' 33.1 629 600 629 603 - 629 604 941 340 934 087

CLIP F02 25 – – – 2.2 646 200 646 207 - 646 204 942 807 942 808

COT 30 1 1 – – 2.0 923 010 923 013 - 923 014 942 283 933 889

COT 54 1 2 – – 2.8 923 020 923 023 - 923 024 942 284 933 891

COT 105 1 4 – – 4.7 923 040 923 043 - 923 044 942 285 933 895

COT 150 1 6 – – 6.6 941 011 942 680 - ** 942 298 942 370

COT J – – – – – 923 050 - - 923 054 - -

Tray Accessories

CLIP FO2CABLOFIL COVER CLIP

CVN CABLOFIL COVER

COT 30/ COT 54DIVIDER STRIP

COT 105/ COT 150DIVIDER STRIP

COT JDIVIDER COUPLER

EZBN 1/4

CE 40 SQUARE SPLICE

WASHER

CE 25 - CE 30SQUARE SPLICE

WASHER

Splicing

EDT SPLICE PLATE

PRE-CLICK SPLICE

ED 275 UNIVERSAL SPLICE BAR

EZT 90 KIT90˚ BEND KIT

RADT 90 KITRADIUS TEE 90˚KIT

EDRNTOOL MOUNTING TOOL

EDRN FAST SPLICE

SWKSPLICE WASHER KIT



EDRN 50* – – – 8.8 558 241 - 558 247 - 941 281 934 032

EDRNTOOL 1 – – – 0.2 558 260 - - - 941 283 934 035

PRECLICK 8 – – – 1.7 942 735 942 736 - 942 739 942 738 942 737

EDT 50 – – – 6.6 558 251 - - 558 254 941 282 934 034

ED 275 50 – – – 14.4 558 221 558 223 - 558 224 941 279 930 621

SWK 50 – – – 3.6 558 071 - 942 746 - - -

CE 25 50 – – – 1.0 558 011 942 459 558 013 558 014 941 274 934 022

CE 30 50 – – – 1.7 558 041 942 460 558 043 558 044 941 275 934 028

CE 40 25 – – – 2.7 558 051 942 461 558 053 558 054 941 276 934 030

EZBN 1/4 50 – – – 1.3 941 084 – – 941 059 – –

FASLOCK XL 25 – – – 1.4 558 320 - 558 327 558 324 942 821 942 822

FASLOCK S 25 – – – 1.4 558 340 - 558 347 588 344 942 869 942 870

EAC – See Accessories Section at bottom of page 4

EZT 90 KIT** 1 – – – 1.5 941 052 942 686 - 941 056 942 307 942 379

RADT 90 KIT 2 1 – – – .66 942 911 - - - - -

RADT 90 KIT 4 1 – – – .66 942 912 - - - - -

*Tool included in every bag of splices**1 Kit contains hardware for 1 tee or 2 90° bends (Consists of 2 pcs EZ T90, 10 EZ BN 1/4, 10 CE 25, 2 CE 40)

FASLOCK

Tray All trays come in 10' lengths

CCFF 5544

CCFF 3300

CCFF 110055

CCFF 115500

*Products listed as “ZF” are only available in Straight Edge Tray.

COUPFIL 1 – – 24.8" 6 559 507

CCLMP21 10 – – – 0.9 942 871

CCLMP34 10 – – – 1.4 942 872

CCLMP45 10 – – – 2.1 942 873

CCLMP52 10 – – – 3.0 942 874

CCLMP64 10 – – – 3.5 942 875

CCLMP76 10 – – – 3.9 942 876

CCLMP95 10 – – – 4.7 942 877

CCLMP108 10 – – – 5.4 942 878

GNDSB 1 – – – 0.07 942 616

GNDCL 1 – – – 0.07 942 866

HD FAS ROLLER 1 – – – 3.5 942 879

HD FAS ROLLER GNDCLGROUNDING LUG

GNDSBGROUNDING LUG

CCLMPCABLE CLAMP

COUPFIL



ZF 30/50* 1 1 2" 10' 3.3 000 011 000 013 000 018 000 014 941 096 933 907

CF 30/100 1 1 4" 10' 4.5 000 021 000 023 000 028 000 024 941 097 933 925

CF 30/150 1 1 6" 10' 5.7 000 031 000 033 000 038 000 034 941 098 933 934

CF 30/200 1 1 8" 10' 7.4 000 041 000 043 000 048 000 044 941 099 933 972

CF 30/300 1 1 12" 10' 9.4 000 051 000 053 000 058 000 054 941 100 934 016

CF 54/50 1 2 2" 10' 5.3 000 061 000 063 000 068 000 064 941 101 934 056

CF 54/100 1 2 4" 10' 6.5 000 071 000 073 000 078 000 074 941 102 934 095

CF 54/150 1 2 6" 10' 7.8 000 081 000 083 000 088 000 084 941 103 934 130

CF 54/200 1 2 8" 10' 9.0 000 091 000 093 000 098 000 094 941 104 934 158

CF 54/300 1 2 12" 10' 13.4 000 101 000 103 000 108 000 104 941 105 933 901

CF 54/450 1 2 18" 10' 22.8 000 251 000 253 000 258 000 254 941 108 933 928

CF 54/500 1 2 20" 10' 24.4 000 301 000 303 000 308 000 304 944 109 933 932

CF 54/600 1 2 24" 10' 27.5 000 401 000 403 000 408 000 404 941 110 933 944

CF 105/100 1 4 4" 10' 9.0 000 891 000 893 000 898 000 894 941 114 934 146

CF 105/150 1 4 6" 10' 10.2 000 901 000 903 000 908 000 904 941 115 934 152

CF 105/200 1 4 8" 10' 13.4 000 911 000 913 000 918 000 914 941 116 934 160

CF 105/300 1 4 12" 10' 21.2 000 921 000 923 000 928 000 924 941 118 934 163

CF 105/450 1 4 18" 10' 25.9 001 931 941 071 941 072 941 073 942 463 942 462

CF 105/500 1 4 20" 10' 27.5 000 941 000 943 000 948 000 944 941 120 934 170

CF 105/600 1 4 24" 10' 30.4 001 031 001 033 001 038 001 034 941 127 933 905

CF 150/300 1 6 12" 10' 24.4 000 961 000 963 942846 000 964 941 122 934 174

CF 150/450 1 6 18" 10' 26.5 001 011 001 013 001 018 001 014 941 125 933 902

CF 150/500 1 6 20" 10' 27.8 001 021 941 078 941 079 941 080 941 126 933 903

ZF 150/600* 1 6 24" 10' 29.5 942 466 942 721 942 591 ** 942 474 942 475

5wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444

4 wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444



FASP 150 1 – – 6" 0.4 014 150 014 153 - 014 154 941 153 930 012

FASP 200 1 – – 8" 0.7 014 200 014 203 - 014 204 941 154 930 014

FASP 300 1 – – 12" 0.9 014 300 014 303 - 014 304 941 155 930 016

FASP 400 1 – – 16" 1.1 014 400 014 403 - 014 404 941 156 930 018

FASP 450 1 – – 18" 1.2 014 450 014 453 - 014 454 941 157 930 020

FASP 500 1 – – 20" 1.3 014 500 014 503 - 014 504 941 158 930 022

FASP 550 1 – – 22" 1.3 014 550 014 553 - 014 554 941 159 930 024

FASP 600 1 – – 24" 1.5 014 600 014 603 - 014 604 941 160 930 026

FASP 700 1 – – 28" 1.8 014 700 014 703 - 014 704 941 162 930 028

FASP 1000 1 – – 40" 2.6 014 010 014 013 - 014 014 941 149 930 006

FASP 2000 1 – – 80" 5.3 014 020 014 023 - 014 024 941 151 930 008

FASP 3000 1 – – 120" 7.9 014 030 014 033 - 014 034 941 152 930 010

AS 50 – – – 6.6 586 020 586 023 - 586 024 941 301 930 675

PROCS 1000 1 – – 39" 2.6 002 920 002 923 - 002 924 941 140 930 088

PROCS 2000 1 – – 79" 5.1 002 930 002 933 - 002 934 941 141 930 090

PROCS 3000 1 – – 118" 8.4 002 940 002 943 - 002 944 941 142 930 092

FASC – See Wall Mounting Section on page 3

CSC – See Wall Mounting Section on page 3

CS – See Wall Mounting Section on page 3

ECLI 10 – – – 0.4 557 190 557 193 - 557 194 942 797 **

PS 400 1 – – 17.5" 1.5 002 730 002 733 - 002 734 941 133 930 076

PS 500 1 – – 21.4" 1.8 002 740 002 743 - 002 744 941 134 930 078

PS 600 1 – – 25.4" 2.1 002 750 002 753 - 002 754 941 135 930 080

EDF 300 1 – – 12" 0.7 561 310 561 313 - - 942 817 942 818

EDF 600 1 – – 24" 1.8 557 610 557 613 - - 942 815 942 816

EDF 1000 1 – – 40" 2.6 561 090 561 093 - - 942 813 942 814

EDF 2/3000 1 – – 10' 8.2 561 020 561 023 - 561 024 941 289 930 643

PFREDF 1 – – – 1.3 561 080 - - 561 084 942 761 942 762

DF 1 – – – 1.3 561 060 561 063 - 561 064 ** **

ERD 10 1 – – – 0.4 561 050 561 053 - - 942 759 942 760

Ceiling Mounting

AS TRAPEZE

HANGING CLIP

PROCS STANDARD

PROFILE

EDF RAIL

ECLI

PS L

ERD 10 BRACE PLATE

PFREDF MOUNTING BRACKET

DF ANGLE MOUNTING

BRACKET

FAS P FAS PROFILE

EACELEVATION

CHANGE HINGE



EZBN 1/4 50 – – – 1.3 941 084 - - 941 059 942 308 -

EZBN 5/16 50 – – – 2.0 942 778 - - 942 779 942 780 -

EZHN 1/4 100 – – – 0.6 941 713 - - 941 067 - -

EZHN 3/8 100 – – – 0.7 941 915 - - 941 069 - -

EZHN 1/2 100 – – – 2.0 941 814 - - 941 068 - -

EZFW 1/4 100 – – – 0.5 941 511 942 687 - 941 065 942 309 942 381

EZFW 3/8 100 – – – 0.6 941 612 942 688 - 941 066 942 310 942 382

EZFW 1/2 100 – – – .15 ** - - - - -

TRP 10 – – 6' 0.7 ** - - - - -

THRD 1/4 – 20 Pitch 1 – – 6' 0.7 942 351 - - 942 471 - -

THRD 3/8 – 16 Pitch 1 – – 6' 1.8 942 353 - - 942 472 - -

THRD 1/2 – 12 Pitch 1 – – 6' 3.1 942 465 - - 942 789 - -

EZCN 1/4 100 – – – 3.0 941 094 - - 941 060 - -

EZCN 3/8 100 – – – 4.0 941 205 - - 941 061 - -

EZCN 1/2 100 – – – 5.0 942 790 - 942 791 942 792 -

SWK 50 – – – 3.5 558 071 – 942 476

CE 25 50 – – – 1.0 558 011 942 459 558 013 558 014 941 274 934 022

CE 30 50 – – – 1.7 558 041 942 460 558 043 558 044 941 275 934 028

CE 40 25 – – – 2.7 558 051 942 461 558 053 558 054 941 276 934 030

ED – See Splicing Section on page 2

EAC 20 – – – .18 - 558 403 - - - -

CA 50 – – – 2.2 801 051 - 801 057 801 054 ** **

FASLOCK – See Splicing Section on page 2

ECLI 10 – – – 0.4 557 190 557 193 - 557 194 ** **

COUPFIL 1 – – 24.8" 6 559 507

EZHN THRD

TRP

EZBN

EZFW

EZCN

SWK

CE 25

CE 30

CE 40

CA ECLI

COUPFIL

Accessories

Wall Mounting

FAS U UNIVERSAL BRACKET

CSC STANDARD C BRACKET

CS STANDARD L BRACKET

CRPUNIVERSAL WALL BRACKET

UC 50 CABLE TRAY STANDOFF

CAT 30/41SNAP-IN WALL

HANGER SUPPORT

FAS P FAS PROFILE

FAS L BRACKET

FVVERTICAL BRACKET

FAS C BRACKET



FASP 150 1 – – 6" 0.4 014 150 014 153 - 014 154 941 153 930 012

FASP 200 1 – – 8" 0.7 014 200 014 203 - 014 204 941 154 930 014

FASP 300 1 – – 12" 0.9 014 300 014 303 - 014 304 941 155 930 016

FASP 400 1 – – 16" 1.1 014 400 014 403 - 014 404 941 156 930 018

FASP 450 1 – – 18" 1.2 014 450 014 453 - 014 454 941 157 930 020

FASP 500 1 – – 20" 1.3 014 500 014 503 - 014 504 941 158 930 022

FASP 550 1 – – 22" 1.3 014 550 014 553 - 014 554 941 159 930 024

FASP 600 1 – – 24" 1.5 014 600 014 603 - 014 604 941 160 930 026

FASP 700 1 – – 28" 1.8 014 700 014 703 - 014 704 941 162 930 028

FASP 1000 1 – – 40" 2.6 014 010 014 013 - 014 014 941 149 930 006

FASP 2000 1 – – 80" 5.3 014 020 014 023 - 014 024 941 151 930 008

FASP 3000 1 – – 120" 7.9 014 030 014 033 - 014 034 941 152 930 010

FASL 100 1 – 4" 7" 0.9 556 100 556 103 ** 556 104 941 257 930 523

FASL 150 1 – 6" 9" 1.0 556 110 556 113 ** 556 114 941 258 930 525

FASL 200 1 – 8" 11" 1.1 556 120 556 123 ** 556 124 941 259 930 527

FASL 300 1 – 12" 14.9" 1.4 556 130 556 133 ** 556 134 941 260 930 529

FASL 400 1 – ** 18.8" 1.8 556 140 556 143 566 144 ** ** **

FASL 450 1 – 18" 20.8" 2.1 556 150 556 153 ** 556 154 942 848 942 600

FASC 100 1 – 4" 7"* 1.4 556 300 556 303 ** 556 304 941 261 930 531

FASC 150 1 – 6" 8.9"* 1.5 556 310 556 313 ** 556 314 941 262 930 533

FASC 200 1 – 8" 10.9"* 1.7 556 320 556 323 ** 556 324 941 263 930 535

FASC 300 1 – 12" 14.9"* 1.9 556 330 556 333 ** 556 334 941 264 930 537

FASC 400 1 – ** 18.8"* 2.4 556 340 556 343 556 344 ** ** **

FASC 450 1 – 18" 20.8"* 2.8 556 350 556 353 556 354 ** 942 596 **

FASU 100 1 3.5 4" 6" 0.3 557 410 557 413 - 557 414 941 267 930 575

FASU 150 1 5.0 6" 8" 0.4 557 420 557 423 - 557 424 941 268 930 577

FASU 200 1 5.5 8" 12" 0.5 557 430 557 433 - 557 434 941 269 930 579

FASU 300 1 5.5 12" 14" 0.8 557 440 557 443 - 557 444 941 270 930 581

FASU 400 1 5.5 16" 18" 1.8 557 450 557 453 - 557 454 941 271 930 583

FASU 500 1 5.5 20" 22" 2.9 557 460 557 463 - 557 464 941 272 930 585

FASU 600 1 5.5 24" 26" 6.4 557 470 557 473 - 557 474 941 273 930 587

FV 100 1 – – 8" 0.7 586 070 586 073 - 586 074 942 805 **

EDF – See Ceiling Mounting Section on page 4

CS 100 1 – 4" 5.7" 0.4 002 700 008 703 - 002 704 941 130 930 070

CS 200 1 – 8" 9.6" 0.8 002 710 002 713 - 002 714 941 131 930 072

CS 300 1 – 12" 13.6" 1.2 002 720 002 723 - 002 724 941 132 930 074

CSC 100 1 – 4" 5.7"* 1.1 002 760 002 763 - 002 764 941 136 930 082

CSC 200 1 – 8" 9.6"* 1.4 002 770 002 773 - 002 774 941 137 930 084

CSC 300 1 – 12" 13.6"* 1.8 002 780 002 783 - 002 784 941 138 930 086

CRP 100 1 3.7 4" 4.6" 0.4 557 213 - - - - -

CRP 150 1 3.7 6" 6.5" 0.7 557 223 - - - - -

CRP 200 1 3.7 8" 8.5" 0.8 557 233 - - - - -

CRP 300 1 3.7 12" 12.4" 1.0 557 243 - - - - -

CRP 400 1 4.7 16" 16.4" 1.3 557 253 - - - - -

CRP 500 1 4.7 20" 20.4" 1.8 557 263 - - - - -

CRP 600 1 4.7 24" 24.3" 2.4 557 273 - - - - -

UC 50 1 – – – 0.1 586 040 586 043 - 586 044 941 304 930 681

CAT 30/41 1 – – – 0.1 942 720 942 799 - 942 742 942 800 942 801

C 50– See Other Mounting Section on page 5

FASP – See Other Mounting Section on page 5

*L measurement is for bottom profile.**Multiple Tray

6 wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444

7wwwwww..ppaassssaannddsseeyymmoouurr..ccoomm



FASCLM KIT 2 – – – 0.2 559 280 - 559 287 559 284 - -

ETC 20 1 0.8 – – 0.2 942 819 - - - - -

ETC 30 1 1 – – 0.4 942 820 - - - - -

EZBC 1/4 1 – – – 0.8 941 063 ** - 941 057 - -

EZBC 3/8 1 – – – 0.8 941 074 ** - 941 058 - -

EZBC 1/2 1 – – – 0.8 942 847 942 847 - ** - -

C 50 1 – – – 0.2 586 130 586 133 - 586 134 941 308 930 694

SBDA 1 – – – 0.2 585 210 - - 585 124 942 950 942 951

CABLEXIT100 1 – – – 0.2 585 160 585 163 585 167 585 164 941 299 930 669

HB 2 KIT 1 – – 9.4" 0.4 942 419 942 686 - 942 943 942 319 942 391

DROP OUT KIT 1 – – 12.25" 0.9 942 895 942 897 - 942 944 942 896 942 898

CCLMP21 10 – – – 0.9 942 871

CCLMP34 10 – – – 1.4 942 872

CCLMP45 10 – – – 2.1 942 873

CCLMP52 10 – – – 3.0 942 874

CCLMP64 10 – – – 3.5 942 875

CCLMP76 10 – – – 3.9 942 876

CCLMP95 10 – – – 4.7 942 877

CCLMP108 10 – – – 5.4 942 878

MFM 100 1 – – 4" 0.2 585 140 585 143 - 585 144 941 297 930 664

MFM 150 1 – – 6" 0.2 585 150 585 153 - 585 154 941 298 930 667

CABLE LABEL CLIP* 50 – – – – 559 127

EZJB 5/16 2 – – 2.5" 2.0 942 016 942 689 - 941 070 942 311 942 383

SZMCKIT 1 – – 7" 0.2 942 445

SZMCCUTR 1 – – – 0.2 942 444

SZMCSWAG 1 – – – 0.7 942 446

FS 41 50 – – – 3.3 599 007 - - - 942 823 942 824

GNDSB 1 – – – 0.07 942 616

GNDCL 1 – – – 0.07 942 866

HD FAS ROLLER 1 – – – 3.5 942 879

*Available in Black, White, Orange, Yellow, Green, Blue, and Gray

Other Mountings

EZBC THREADED ROD HANGER

HB 2 WALL/FLOOR

TERMINATION BRACKET

DROP OUTCABLE DROP OUT

SBDCONDUIT AND BOX SUPPORT

CABLEXIT

ETCTRAY BEAM SUPPPORT

MFMMETALLIC MULTIFIX PLATE

CABLE LABEL CLIP

C 50ELECTRICAL BOX SUPPORT

HD FAS ROLLER

EZJB 5/16J-BOLT

SZMCKITSEISMIC BRACING KIT

FS 41FASTRUT CONNECTOR

GNDCLGROUNDING LUG

SZMCCUTRCABLE CUTTER

SZMCSWAG HAND SWAGER

GNDSBGROUNDING LUG

FASCLM KITBEAM CLAMP

CCLMPCABLE CLAMP

Cablofil wire cable tray is available in a variety of finishes to meet any industry need, from decorative to extreme

environments. Use this color code to help you to determine the best finish for your application and its availability.

Finishes

For a more detailed explanation of finish standards and compatibility, visit: www.cablofil.com.

CABLOFIL PRODUCT CODE:

Our part number makes it easy to

identify part type, size and finish.

Please use this code whenever ordering or

specifying any Cablofil product.

FOR TRAY

TYPE OF TRAY DEPTH IN MM WIDTH IN MM FINISH CODE

FOR SUPPORTS ANDOTHER PRODUCTS

FASU 300 PG

PRODUCT CODE SIZE IN MM FINISH CODE

CF EZ54 / 100

PG

EZ

GC

316L

304L

PE

BL

DC

Pre-Galvanized: ASTM A 653 Exterior applications: Industrial plantsContinuous Galvanization Norm NF/A 91-131 Interior applications: Commercial offices, Computer roomsBefore Fabrication

Electrozinc: ASTM B 633 Interior applications:Electrozinc plating Norm NF/EN 12-329 Commercial offices, Computer rooms

Hot Dipped Galvanized: ASTM A 123 Exterior applications:After Fabrication Norm NF/EN/ISO 14-61 Corrosive Environments

Dacromet: ASTM F 1136 Exterior applications:Zinc and Aluminum Protection Corrosive EnvironmentsEquivalent to Hot Dip Galvanization

Stainless Steel 304L ASTM A 380 Clean Rooms, Food preparation, Wash down areasNorm NF 10-088-2

Stainless Steel 316L ASTM A 380 Marine Environments: Oil rigs, Ships, Refineries, Norm NF 10-088-2 Power Plants, Waste Water, Treatment Plants, Cement

Plants, Pulp and Paper Mills

Black Painted: ASTM B 633 Exposed interior applications: Retail stores, Hospitals,Black Powder Coated Control cabling, Data centers

Custom Painted: ASTM B 633 Exposed interior applications: Schools, Casinos, Custom Color Data centers, Control cabling, HospitalsPowder Coated

SYMBOL FINISH TESTING METHOD APPLICATION

Catalog

Number Wire Length and Type

Catalog

Number Wire Length and Type

PTRA6STR 6" Stranded THHN12

PTRA6SOL 6" Solid THHN12

PTRA6STRB25 25" Stranded THHN12

PTRA6SOLB25 25" Solid THHN12

Specification Grade GFCIs (Non feed-though type)

PT1595* Duplex — Fed Spec Grade 15A 125V 5-15R


PT1595NTL* LED Nightlight Combination 15A 125V 5-15R

PT2095NTL* LED Nightlight Combination 20A 125V 5-20R

PT1595TR* Tamper-Resistant 15A 125V 5-15R

PT2095TR* Tamper-Resistant 20A 125V 5-20R

Hospital Grade GFCIs (Non feed-though type)

PT1595HG* Duplex 15A 125V 5-15R

PT2095HG* Duplex 20A 125V 5-20R

PT1595HGNTL* LED Nightlight Combination 15A 125V 5-15R

PT2095HGNTL* LED Nightlight Combination 20A 125V 5-20R

PT1595HGTR* Tamper-Resistant 15A 125V 5-15R

PT2095HGTR* Tamper-Resistant 20A 125V 5-20R

Catalog Ratings NEMA

Number Description A. V. Config. No.

Specification Grade Receptacles

PT5262A* Extra Heavy-Duty 15A 125V 5-15R

PT5362A* Extra Heavy-Duty 20A 125V 5-20R

PTTR62* Extra Heavy-Duty — Tamper-Resistant 15A 125V 5-15R

PTTR63* Extra Heavy-Duty — Tamper-Resistant 20A 125V 5-20R

PT26252* Decorator 15A 125V 5-15R

PT26352* Decorator 20A 125V 5-20R

PTIG26262* Decorator — Isolated Ground 15A 125V 5-15R

PTIG26362* Decorator — Isolated Ground 20A 125V 5-20R



PTIG5262* Duplex — Isolated Ground 15A 125V 5-15R

PTIG5362* Duplex — Isolated Ground 20A 125V 5-20R

Hospital Grade Receptacles

PT8200* Extra Heavy-Duty 15A 125V 5-15R

PT8300* Extra Heavy-Duty 20A 125V 5-20R

PTTR62H* Extra Heavy-Duty — Tamper-Resistant 15A 125V 5-15R

PTTR63H* Extra Heavy-Duty — Tamper-Resistant 20A 125V 5-20R

PT26262HG* Decorator 15A 125V 5-15R

PT26362HG* Decorator 20A 125V 5-20R

U.S. Pat. No. 6,994,585

P&S PlugTail Right Angle Connectors

Third Party Compliance

I — Ivory

W — White

GRY — Gray

BK — Black

BL — Blue

Red — Red

LA — LightAlmond

1. Blue only available in Spec Grade

Duplex Receptacles

2. For Isolated Ground (IG) Receptacles,

no color designation = Orange

3. For all other receptacles, no color

designation = Brown

*Color Designation

cULus Listed, File Number E140596,

Standard UL498, Federal Specification

WC596

PPTTTTRR6633WW

PPTTTTRR6633HHWW

PPTTTTRR6633HHLLAA

PPTT2266335522LLAA

PPTT22009955HHGGNNTTLLLLAA

PPTT22009955LLAA

PPTT55336622AAWW

PPTT88330000WW

PPTT22009955HHGGTTRRWW

PPTTIIGG55336622

PPTT22009955TTRRLLAA

PPTT55336622LLAA

PPTT2266336622HHGGII

PPTTIIGG2266336622

Electrical Devices

8 9wwwwww..ssoouutthhwwiirree..ccoommwwwwww..ssoouutthhwwiirree..ccoomm

NUMBER OF CONDUCTORS COLOR SEQUENCECOLOR SEQUENCE

277/480Y

NUMBER OF

CONDUCTORS

CONDUCTOR

SIZE (AWG)/

# OF PHASE

CONDUCTORS

CONDUCTOR

TYPE*

GROUNDING/

BONDING

CONDUCTOR

AMPACITY (AMPS)‡

60°C

OVERALL

DIAMETER

(inches)

GREEN THHN

COPPER GROUND

(AWG)

WEIGHT

(lbs./1000 ft.)75°C 90°C

STANDARD PACKAGE

COIL (feet) REEL (feet)

500 Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition. *Circuit sizes 12 AWG and 10 AWG also available as stranded conductors.‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15. If the equipment is markedfor use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).60°C - When terminated to equipment for circuits rated 100 amperes or less or marked for size 14 through 1 AWG conductors.75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.

12 / 2 Solid 10 solid AL 12 0.445 110 20 20 20 250 1000

12 / 3 Solid 10 solid AL 12 0.480 134 20 20 20 250 1000

12 / 4 Solid 10 solid AL 12 0.515 180 20 20 20 250 1000

10 / 2 Solid 8 solid AL 10 0.520 162 30 30 30 250 1000

10 / 3 Solid 8 solid AL 10 0.565 202 30 30 30 250 1000

10 / 4 Solid 8 solid AL 10 0.670 266 30 30 30 250 1000

COLOR CODING Standard Products

2 black, white

3 black, white, red

4 black, white, red, blue

Grounding Conductor green

Other special colors are available subject to economic order quantity. Custom cable constructions available for homeruns, multiple oroversized neutrals and isolated grounds. Subject to economicorder quantity.

2 brown, grey

2 orange, grey

2 yellow, grey

2 purple, grey

3 brown, yellow, grey

3 brown, orange, grey

4 brown, orange, yellow, grey

4 brown, yellow, purple, grey

Grounding Conductor green

CONDUCTOR

TYPE*

GROUNDING/

BONDING

CONDUCTOR

AMPACITY (AMPS)‡OVERALL

DIAMETER

(inches)

WEIGHT

(lbs./1000 ft.)75°C

STANDARD PACKAGE

COIL (feet)

CONDUCTOR

SIZE (AWG)/

# OF PHASE

CONDUCTORS

Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition. *Circuit sizes 12 AWG and 10 AWG also available as stranded conductors. ‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15. If the equipment is markedfor use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).60°C - When terminated to equipment for circuits rated 100 amperes or less or marked for size 14 through 1 AWG conductors.75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.

60°C 90°C

14 / 2 Solid 12 solid AL 0.385 63 15 15 15 250 1000

14 / 3 Solid 12 solid AL 0.410 78 15 15 15 250 1000

14 / 4 Solid 12 solid AL 0.435 96 15 15 15 250 1000

12 / 2 Solid 10 solid AL 0.430 88 20 20 20 250 1000

12 / 3 Solid 10 solid AL 0.445 110 20 20 20 250 1000

12 / 4 Solid 10 solid AL 0.480 134 20 20 20 250 1000

10 / 2 Solid 8 solid AL 0.485 123 30 30 30 250 1000

10 / 3 Solid 8 solid AL 0.520 162 30 30 30 250 1000

10 / 4 Solid 8 solid AL 0.538 202 30 30 30 250 1000

REEL (feet)


2 black, white

3 black, white, red


NUMBER OF CONDUCTORS COLOR SEQUENCE

Other special colors are available subject to economic order quantity.

2 brown, grey

2 orange, grey

2 yellow, grey

2 purple, grey

3 brown, yellow, grey



4 brown, yellow, purple, grey

NUMBER OF

CONDUCTORS

COLOR SEQUENCE

277/480Y

MCAP™ Cable - All Purpose

HCF MCAP™ Cable - All Purpose Hospital Care Facility

U.S. Pat. No. 6,486,395

U.S. Pat. No. 6,486,395

CONDUCTOR SIZE/

# OF COND.

(AWG/kcmil)

GROUNDING

CONDUCTOR

(AWG)†

APPROXIMATE

DIAMETER OVER

ARMOR (inches)

WEIGHT

(lbs/1000 ft)

NON WATERTIGHT

CONNECTOR***

(MODEL #)

AMPACITY (AMPS)‡

75°C 90°C

CONDUCTOR SIZE/

# OF COND.

(AWG/kcmil)

GROUNDING

CONDUCTOR

(AWG)†

APPROXIMATE

DIAMETER OVER

ARMOR (inches)

WEIGHT

(lbs/1000 ft)

NON WATERTIGHT

CONNECTOR***

(MODEL #)

AMPACITY (AMPS)‡

75°C 90°C

6/3 6 bare 0.784 240 50 60 NWT 083-075

6/4 6 bare 0.850 289 50 60 NWT 090-075

4-3 6 bare 0.879 298 65 75 NWT 104-100

4-4 6 bare 0.957 368 65 75 NWT 097-100

2-3 4 bare 0.998 411 90 100 NWT 104-100

2-4 4 bare 1.089 508 90 100 NWT 111-100

1-3 4 bare 1.108 496 100 115 NWT 118-100

1-4 4 bare 1.213 619 100 115 NWT 125-125

1/0-3 4 bare 1.188 578 120 135 NWT 125-125

1/0-4 4 bare 1.302 727 120 135 NWT 132-125

2/0-3 4 bare 1.274 678 135 150 NWT 132-125

2/0-4 4 bare 1.398 858 135 150 NWT 148-150



NUMBER OF

CONDUCTORS

NUMBER OF

CONDUCTORSCOLOR SEQUENCE

277/480Y

3 black, white, red


Grounding Color Bare

COLOR SEQUENCE

120/208Y


Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition.‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15.If the equipment is marked for use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).

60°C - When terminated to equipment for circuits rated 100 amperes or less or marked for size 14 through 1 AWG conductors.75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.

Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.†Available with oversized grounding conductor when used for parallel feeds on special orders.***Recommended connectors may require upsizing to accommodate armor looseness after cutting.

Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition.‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15.If the equipment is marked for use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).

75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.

Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.†Available with oversized grounding conductor when used for parallel feeds on special orders.***Recommended connectors may require upsizing to accommodate armor looseness after cutting.

AlumaFlex™ Cable

3/0-3 4 bare 1.38 830 155 175 NWT 139-125

3/0-4 4 bare 1.61 1135 155 175 NWT 166-150

4/0-3 2 bare 1.59 1086 180 205 NWT 157-150

4/0-4 2 bare 1.74 1370 180 205 NWT 175-200

250-3 2 bare 1.73 1272 205 230 NWT 175-200

250-4 1 bare 1.90 1630 205 230 NWT 193-200

300-3 1 bare 1.84 1470 230 255 NWT 184-200

300-4 1 bare 2.02 1870 230 255 NWT 213-250F

350-3 1 bare 1.94 1649 250 280 NWT 202-300F

350-4 1/0 bare 2.13 2120 250 280 NWT 213-250F

400-3 1 bare 2.04 1826 270 305 NWT 213-250F

400-4 3/0 bare 2.23 2410 270 305 NWT 224-250F

500-3 1 bare 2.20 2172 310 350 NWT 213-250F

500-3 2/0 bare 2.27 2151 310 350 NWT 213-250F

500-3 250 bare 2.27 2200 310 350 NWT 213-250F

500-4 3/0 bare 2.42 2870 310 350 NWT 246-250F

500-4 250 bare 2.95 2863 310 350 NWT 246-250F

600-3 1/0 bare 2.43 2540 340 385 NWT 257-250F

600-4 3/0 bare 3.40 3294 340 385 NWT 271-300F

600-4 400 bare 2.93 3677 340 385 NWT 299-300F

750-3 1/0 bare 2.63 3112 385 435 NWT 271-300F

750-3 3/0 bare 2.63 3171 385 435 NWT 271-300F

750-4 3/0 bare 2.90 4080 385 435 NWT 299-300F

750-4 500 CU bare 3.20 5532 385 435 NWT 328-350F

900-4 250 bare 3.11 4827 425 480 NWT 313-300F


Low Voltage Colors

AlumaFlex™ Cable

Type MC - 3/0 AWG through 900 kcmil - Non Jacketed THHN/THWN-2

Type MC - 6 AWG through 2/0 AWG - Non Jacketed, Tri-Striped Black XHHW-2

triple e™ Aluminum Alloy


HIGH Voltage Colors


Color sequence for special colors are available subject to economic order quantity.

3 black, white, red


Grounding Color Bare

NUMBER OF CONDUCTORSCOLOR SEQUENCE

120/208Y

Note: Phase conductors are black with printed ID.

product reference guide - s3. · pdf fileg i n e e r i n g t h a t ... 1 6 20" 10'...

Documents