profil en - movetec- end cap 19x45 z part n° 22.1001/1 - end cap 32x32 z part n° 22.1002/1 - end...
TRANSCRIPT
TABLE OF CONTENT INTRODUCTION
2 MINITEC NEWS 2009
CONTENTS3 END CAP Z WITH HAMMER TAPS
3 END CAP 45X45 VA
4 ANGLE 25 GD-Z
4 ANGLE 45X90 GD-Z
5 ANGLE 90 GD-Z
5 HINGE 19 S
6 HINGE 32 S
6 HINGE 45 S
7 DOOR HINGE SMALL
7 DOOR HINGE LARGE
8 T-SLOT MAGNET
8 SEALING PROFILE
9 SLIDE LR6 COMPACT
9 SLIDE LR6 COMPACT
10 RAIL LR 6 COMPACT
10 UNIVERSAL CLAMPING SOCKET
11 SLIDE G 32
11 BRACKET CONSOLE FOR MINIATURE ADJUSTMENT UNIT
12 CENTER DRIVE - 3 WHEELS SYSTEM
12 CUP HOLDER
MINITEC NEWS 2009 3
END CAP Z WITH HAMMER TAPS Part. N° 22.1007/1
TECHN. DATA/ITEMS SUPPLIED
- End cap 19x45 Z Part N° 22.1001/1
- End cap 32x32 Z Part N° 22.1002/1
- End cap 45x45 Z Part N° 22.1004/1
- End cap 45x90 Z Part N° 22.1007/1
APPLICATIONS
- Good clamping effectiveness via hammer taps in the star-shaped hole
- Simple disassembly
- The end cap can be re-used with replacement pins
ASSEMBLY
- Hammer the taps flush using a plastic hammer
- For dismantling, hammer the pin with a ø 4 centre punch
- Replacement pins (10 pack) Part N° 221009/1
END CAP 45X45 VA Part. N° 21.0026/0
TECHN. DATA/ITEMS SUPPLIED
- End cap stainless steel
- With fixing pan head screw M8 x 10 stainless steel
APPLICATIONS
- For Profile VA and Profile AL
- ESD on request
- Rounded edges
ASSEMBLY
- Tap an M8 thread 12 mm deep into the profile
- Place the end cap on and turn until the screw safety catches
- Screw in the screw included in the scope of delivery with SW4
4 MINITEC NEWS 2009
ANGLE 25 GD-Z Part. N° 21.0969/0
TECHN. DATA/ITEMS SUPPLIED
- Aluminium GD, powder coated, grey
- Fixing kit
- Removable centering tabs
- Weight 0,066 kg
APPLICATIONS
- General constructions, particularly useful for subsequent fitting of profiles into existing constructions
- Fixing of panel elements, table tops
- Strengthening of profile constructions
ASSEMBLY
- Use fixing kit from supply schedule
- Break centering tabs with pliers if non-aligning grooves
- For subsequent mounting into vertical profiles use square nut M8 with position-fixing Part N° 21.1351/2
- End cap MW 25 GD-Z Part. N° 22.0997/1
ANGLE 45X90 GD-Z Part. N° 21.1397/0
TECHN. DATA / ITEMS SUPPLIED
- Aluminium GD, powder coated, grey
- Fixing kit
- Weight 0,281 kg
APPLICATIONS
- General constructions, particularly useful for subsequent fitting of profiles into existing constructions
- Fixing of panel elements, table tops
- Strengthening of profile constructions
ASSEMBLY
- Use fixing kit from supply schedule
- For mounting into vertical profile use square nut M8 with position-fixing Part N° 21.1351/2
- Recommended locking torque 20 Nm
- Use hammer-head screw Part N° 21.1370/0
- Suitable end cap MW 45x90 GD-Z Part N° 22.0998/1
MINITEC NEWS 2009 5
ANGLE 90 GD-Z Part. N° 21.0978/0
TECHN. DATA / ITEMS SUPPLIED
- Aluminium GD, powder coated, grey
- Fixing kit
- Weight 0,460 kg
APPLICATIONS
- For profiles 90 and 180
- General constructions, particularly useful for subsequent fitting of profiles into existing constructions
- Fixing of panel elements, table tops
- Strengthening of all profile connections
ASSEMBLY
- Use fixing kit from supply schedule
- For subsequent mounting into vertical profiles use square nut M8 with position-fixing Part N° 21.1351/2
- Hammer head screw can be used
- Recommended locking torque 20 Nm
- Suitable end cap MW 90 GD-Z Part N° 220999/1
HINGE 19 S Part. N° 21.1044/0
TECHN. DATA / ITEMS SUPPLIED
- Aluminium GD, powder coated, grey
- Without fixing kit
- with end caps
- Weight 0,100 kg
- Load max. 600 N
APPLICATIONS
- Suitable for large doors and flaps of profile type 19 or 32
- Guard units
- Connection of profiles 19 and 32 at any angle
ASSEMBLY
- Fasten hinge with 4 M6 x 18 bolts and 4 square nuts on the profile groove, or with screws corresponding to the material thickness directly on the panel elements
- For heavy-duty applications use multiple hinges
6 MINITEC NEWS 2009
HINGE 32 S Part. N° 21.1055/0
TECHN. DATA / ITEMS SUPPLIED
- Aluminium GD, powder-coated, grey
- Without fixing kit
- With end caps
- Weight 0,105 kg
- Load max. 600 N
APPLICATIONS
- Suitable for large doors and flaps
- Guard units
- Connection of profiles 19, 32 and 45 at any angles
ASSEMBLY
- Fasten hinge with 4 M6 x 18 bolts and 4 square nuts on the profile groove or with screws corresponding to the material thickness directly on the panel elements
- Fasten hinge with M8 x 30 bolt on the 45 x 45 profile face side; fasten the other hinge half with M6 x 20 bots and square nuts on the profile groove or with M6 x 18 bolts corresponding to the material thicknes
- For heavy-duty applications use multiple hinges
HINGE 45 S Part. N° 21.1098/0
TECHN. DATA / ITEMS SUPPLIED
- Aluminium GD, powder-coated, grey
- Without fixing kit
- With End caps
- Weight 0,110 kg
- Load max. 600 N
APPLICATIONS
- Suitable for large doors and flaps
- Guard units
- Connection of profiles at various angles
- For higher loads use more hinges
ASSEMBLY
- 1: 2 screws M8 x 30
- 2: 2 screws M6 x 18, square nuts M6, 1 screw M8 x 30
- 3: 2 screws M6 x 18, 2 square nuts M6, 2 screws M6 for panel element according to material
- 4: 4 screws M6 x 18, 4square nuts M6
MINITEC NEWS 2009 7
DOOR HINGE SMALL Part. N° 21.0973/0
TECHN. DATA/ITEMS SUPPLIED
- Aluminium
- Fixing kit
- Weight 0,120 kg
APPLICATIONS
- Suitable for large doors and lids
- Guard units
- Connection of profiles at any angle
ASSEMBLY
- Use fixing kit from supply schedule
DOOR HINGE LARGE Part. N° 21.0970/0
TECHN. DATA/ITEMS SUPPLIED
- Aluminium
- Fixing kit
- Weight 0,235 kg
APPLICATIONS
- Suitable for large doors and lids
- Guard units
- Connection of profilles at any angle
ASSEMBLY
- Use fixing kit from supply schedule
8 MINITEC NEWS 2009
T-SLOT MAGNET Part. N° 21.0023/0
TECHN. DATA/ITEMS SUPPLIED
- 1 Magnet NeFeB zinc-plated
- Without fixing kit
- Weight 0,13 kg
- Attention: Electric- and memory devices can be faulted by the magnet
APPLICATIONS
- Adhesive magnet for tools
- Below conveyors as guidance, for magnetisable trnasported material or for higher conveyiry speed
ASSEMBLY
- Insert magnet into t-slot
- For fixing: (strongly recommended) Use end cap Al, set screw M8 x 12 with square nut M8 or t-slot bar
SEALING PROFILE Part. N° 22.1011/0
TECHN. DATA/ITEMS SUPPLIED
- Weight 0,122 kg/m
- Length 100 m
APPLICATIONS
- Sealing of doors, lids and other constructions against water, dust and noise
ASSEMBLY
- Press into profile groove
MINITEC NEWS 2009 9
SLIDE LR6 COMPACT Part. N° 28.0140/0
TECH. DATA / ITEMS SUPPLIED
- Aluminium, all faces machined
- 3 Double row, angular-contact bearings
- Assembled ready for use
- Weight 0,194 kg
APPLICATIONS
- MiniTec linear guide systems LR 6
- Material-handling
- Measuring devices
- Doors
ASSEMBLY
- Slip slide onto rail
- Adjust clearance with key 2,5 A/F
- Tighten fixing screw with a torque of 20 Nm
SLIDE LR6 COMPACT Part. N° 28.0127/0
TECHN. DATA/ITEMS SUPPLIED
- Slide PEUHMW, black
- With square nut M8, steel zinc-plated
- Weight 0,068 kg
APPLICATIONS
- Material-handling
- Measuring devices
- Doors
ASSEMBLY
- Slip slide onto rail
- Adjust slide clearance with hexagon key
10 MINITEC NEWS 2009
RAIL LR 6 COMPACT Part. N° 28.0016/0
TECH. DATA / ITEMS SUPPLIED
- Aluminium, natural anodized E6/EV 1
- 2 Shafts Cf 53 h6, steel
- With fixing bores Ø 8,5 mm, grid: 150 mm
- Weight 1,779 kg/m
- Lenght 4 m
APPLICATIONS
- Material-handling
- Measuring devices
- Doors
ASSEMBLY
- Fasten rail with countersunk screws M8 x 20 and square nut M8 on MiniTec profile
UNIVERSAL CLAMPING SOCKET Part. N° P20.060/0
TECHN. DATA/ITEMS SUPPLIED
- Case PA 6 GF
- Knurled screw steel
- Weight 0,037 kg
APPLICATIONS
- For assembly of pneumatic switches for learning and training purposes
- To fasten diverse pneumatic switches
- Fastening of valves including those from different manufacturers
ASSEMBLY
- Simple pneumatic accessories fastened with M3 screws (not in scope of delivery) onto the clamping socket
- By pressing the knurled screw, the clamping socket can be fit into the slot
- When released, it is automatically indexed
MINITEC NEWS 2009 11
SLIDE G 32 Part. N° 28.0355/0
TECHN. DATA / ITEMS SUPPLIED
- Slide aluminium anodized
- Slide bearing (plastic)
- Without adjusting units
- Weight 0,314 kg
APPLICATIONS
- to adjust light barriers, reflectors, side guides etc.
ASSEMBLY
- Insert the slides of the mini adjustment unit into the sliding guides and turn the spindle
- Adjust using the play of the M6 tensioning screw
- Fasten the spindle bearing to the handle profile 32
BRACKET CONSOLE FOR MINIATURE ADJUSTMENT UNIT Part. N° 28.0371/0
TECHN. DATA/ITEMS SUPPLIED
- Console aluminium, natural anodized
- Without fixing kit
- Weight 0,044 kg
APPLICATIONS
- For connection of two adjustment units Part N° 28.0351/0, 28.0352/0 and 28.0353/0
- For connecting small loads, such as light barriers, sensors etc.
ASSEMBLY
- Each with two M6 threads, 10 mm deep, separation of 25 mm placed into slides
- Connect adjustment units with cylinder head screws M6x15
12 MINITEC NEWS 2009
CENTER DRIVE - 3 WHEELS SYSTEM Part. N° 29.5260/0
TECHN. DATA/ITEMS SUPPLIED
- Cylinder, steel zink-plated
- Ball bearings on both sides
- With Fixing kit
- Part. N° 29.5260/0 Weight with drive ø 50: 50,800 kg/m
- Part. N° 29.5261/0 Weight with drive ø 70: 70,566 kg/m
APPLICATIONS
- Space saving drive
- Motor below conveyor
- Suitable for nosebar on both ends
ASSEMBLY
- First install sheets
- Assemble driving drum, tensioning drive and bearing housing
- Assemble sprocked wheel, chain and motor. Adjust belt-tension after that
CUP HOLDER Part. N° 32.0544/0
TECHN. DATA/ITEMS SUPPLIED
- Cup holder aluminium anodized
- Cup with MiniTec company logo
- With fixing kit
- Weight 0,580 kg
APPLICATIONS
- Cup or bottle holder for workplace systems
- With cut-out for cup handel
ASSEMBLY
- Screw on profile constructions by using fixing kit