prt-ctrl-din protege gx din rail system … cell backup battery n+ n- nbna +-v1+ v1+ v1+ v1+ v1+ v1+...

PRT-

CTR

L-D

IN

Protege GX DIN Rail Integrated System Controller

Installation Manual

2 PRT-CTRL-DIN Protege GX DIN Rail Integrated System Controller Installation Manual | March 2012

The specifications and descriptions of products and services contained in this document were correct at the time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form or by any means (electronic or mechanical), for any purpose, without the express written permission of Integrated Control Technology Limited. Designed and manufactured by Integrated Control Technology Limited. Protege® and the Protege® Logo are registered trademarks of Integrated Control Technology Limited. All other brand or product names are trademarks or registered trademarks of their respective holders.

Copyright © Integrated Control Technology Limited 2003-2012. All rights reserved.

Publication Date: March 2012

PRT-CTRL-DIN Protege GX DIN Rail Integrated System Controller Installation Manual | March 2012 3

Contents

1 Introduction _______________________________________________________________ 5

1.1 Document Conventions ................................................................................................. 5

2 Mounting _________________________________________________________________ 6

2.1 Removal ......................................................................................................................... 6

3 Connections ______________________________________________________________ 7

3.1 Power Requirements ..................................................................................................... 7

3.2 Encrypted Module Network ........................................................................................... 9

3.3 Telephone Dialer .......................................................................................................... 10

3.4 Ethernet 10/100 Network Interface ............................................................................. 11

4 Configuration ____________________________________________________________ 12

4.1 Setting the IP Address ................................................................................................. 12

4.2 Setting the IP Address from a Keypad ........................................................................ 13

4.3 Configuring a Controller via the Protege GX Software ................................................ 14

Adding a Controller with Default Records ................................................................... 15

Adding a Controller Based on an Existing Controller .................................................. 16

Configuring a Controller .............................................................................................. 17

4.4 Addressing Modules .................................................................................................... 23

5 Door Access Control ______________________________________________________ 25

5.1 Card Reader Connection ............................................................................................. 25

5.2 Multiple Wiegand Card Reader Connection ................................................................ 26

5.3 Door Contact Connection ........................................................................................... 27

5.4 Lock Output Connection ............................................................................................. 28

5.5 Programming the Onboard Reader ............................................................................. 29

6 Inputs ___________________________________________________________________ 31

6.1 Onboard Inputs ........................................................................................................... 31

6.2 Resistor Value Options ................................................................................................ 32

6.3 Trouble Inputs ............................................................................................................. 33

7 Outputs _________________________________________________________________ 34

7.1 Bell/Siren Output ......................................................................................................... 34

7.2 Relay Outputs .............................................................................................................. 35

7.3 Reader Outputs ........................................................................................................... 35

8 Hardware Configuration ___________________________________________________ 36

8.1 Defaulting a Controller ................................................................................................. 36


9 LED Indicators ___________________________________________________________ 37

9.1 Power Indicator ........................................................................................................... 37

9.2 Status Indicator ........................................................................................................... 37

9.3 Fault Indicator .............................................................................................................. 37

9.4 Ethernet Link Indicator ................................................................................................ 38

9.5 Modem Indicator ......................................................................................................... 38

9.6 R1/R2 Reader Data Indicators .................................................................................... 38

9.7 Bell Indicator................................................................................................................ 38

9.8 Relay Indicators ........................................................................................................... 39

9.9 Zone (Input) Indicators ................................................................................................ 39

10 Mechanical Diagram ______________________________________________________ 40

11 Mechanical Layout _______________________________________________________ 41

12 Technical Specifications ___________________________________________________ 42

12.1 Current and Validation Example .................................................................................. 43

13 Ordering Information ______________________________________________________ 44

14 Warranty ________________________________________________________________ 45


1 Introduction

Thank you for purchasing the Protege GX DIN Rail Integrated System Controller by Integrated Control Technology. The Protege System is an advanced technology security system designed to provide integration with building automation, apartment complex control and HVAC in one flexible package. Communication is over a proprietary high speed protocol across an AES encrypted local area network and an encrypted proprietary RS-485 module network. Using modular-based hardware design, system installers have the flexibility to accommodate any installation whether it's small, large, residential or commercial.

The Controller is the central processing unit of the Protege System. It communicates with all system modules, stores all configuration and transaction information, processes all system communication, and reports alarms and system activity to a monitoring station or remote computer.

Flexible module network architecture allows large numbers of modules to be connected to the RS-485 Module Network. Up to 250 modules can be connected to the Protege System in any combination to the network up to a distance of 900M (3000ft). Communication beyond this distance requires the use of a RS-485 Network Extender

The current features of the Protege GX DIN Rail Controller include:

Internal industry standard 10/100 Ethernet

32 Bit advanced RISC processor with 2Gb total memory

8 high security monitored inputs

NIST Certified AES 128, 192 and 256 Bit Encryption

When receiving the DIN Rail Controller you should find the kit contains the items listed below. Please note that if you do not have the correct contents, you should contact your distributor immediately.

Protege GX DIN Rail Integrated System Controller

Protege GX DIN Rail Integrated System Controller Quick Start Guide

18 1K ohm resistors

1 330 Ohm EOL Termination Resistor

1 Diode 1N4007 1A 400V (Axial)

DIN Rail Mounting Strip

For more information on the Protege GX DIN Rail Integrated System Controller and other Integrated Control Technology products please login to www.incontrol.co.nz.

1.1 Document Conventions

Indicates a warning or cautionary message

Indicates an important note or advisory information

Indicates a hint or suggestion

[TEXT] Bold text enclosed in brackets is used to show a section number or address of a programmable option or information on programming shortcut sequences

i


2 Mounting

The Protege DIN Rail Controller is supplied as a DIN Rail mount module and is designed to mount on standard DIN Rail either in dedicated DIN cabinets, Protege Jumbo Cabinet Enclosure with DIN Rail Gear Plates, or generic DIN Rail mounting strip. A section of this DIN Rail strip bas been provided as a mounting option.

When installing the DIN Rail Controller ensure that there is adequate clearance around all sides of the enclosure and air flow to the vents of the unit is not restricted. It is recommended to install the DIN Rail Controller in a location that will facilitate easy access for wiring. It is also recommended that the DIN Rail Controller is installed in electrical rooms, communication equipment rooms, closets or in an accessible area of the ceiling.

Step 1

Hook the lower tabs under the bottom edge of the DIN Rail.

Step 2

Push the Controller against the DIN Rail mount and press firmly on the top centre of the Controller until the upper tab clips over the upper rail.

To reduce the risk of damage caused by debris during the installation, install the cabinet enclosure when the unit is not installed on the rails.

2.1 Removal The Controller can be removed from the DIN Rail mount using the following steps:

Step 1

Insert a flat blade screwdriver into the hole in the white tab at the top centre of the Controller.

Step 2

Lever the tab up and rotate the unit off the DIN Rail mount.

i


3 Connections

3.1 Power Requirements The Protege DIN Rail Controller is supplied by a 12V DC power supply connected to the N+ and N- terminals. It does not contain internal regulation or isolation. It is recommended that an ICT PRT-PSU-DIN is used for this purpose, although any clean 12V DC supply would be suitable. In a small installation this same power supply can be used to supply the module network as well, so long as the maximum load of the power supply is not exceeded.

If using the PRT-PSU-DIN module, it can support battery backup and can be connected to the module network to provide a monitored supply. Please refer to the PRT-PSU-DIN installation manual for specific details of the connections.

Example Power Supply Connection

B+B- L NNAN+ N- NB

PRT-CTRL-DIN PRT-PSU-DIN

Gel Cell Backup Battery

NAN+ N- NB

+

-

V1+ V-V1+ V1+ V1+ V1+ V1+ V- V- V- V- V-

Mains Input

To other moduleson network


In larger installations, the power supply may need to be split to allow for load sharing between several supplies.

Example multiple PSU Connection

Warning: When using multiple power supplies it is important to ensure that all ground connections (V-) are connected between all power supplies and that no power connections (V+) are connected between any power supplies.

The auxiliary outputs (V- V+) of the PRT-CTRL-DIN can be used to supply other equipment. Note that there is no on-board regulation or isolation for these outputs - they are a fused feed-through from the N+ N- input terminals. When using these outputs to supply other devices, be sure not to exceed the rating of the internal fuses as specified in the Technical Specifications (see page 42).

Warning:

Installation should be made by qualified service personnel and should conform to all local codes and in accordance with the National Electrical Codes (NEC US) or the Canadian Electrical Codes (CEC Canada).

Termination of wiring to the Protege DIN Rail Controller while power is applied or the battery is connected may cause serious damage to the unit and will VOID ALL WARRANTIES OR GUARANTEES. Power the unit only after all wiring, configuration and jumper settings are completed.

Module #3 Module #1 PRT-CTRL-DIN

NAN+ N- NBNAN+ N- NB NAN+ N- NB

Module #2

NAN+ N- NB

Power Supply #3 Power Supply #2 Power Supply #1


3.2 Encrypted Module Network The Protege DIN Rail Controller incorporates encrypted RS-485 communications technology. Connection of the communications should be performed according to the following diagram.

Always connect the Controller's NA and NB terminals to the NA and NB terminals of the expansion devices and keypads. The N+ and N- must connect to a 12V power supply source capable of supplying the peak current drawn by all modules.

If a shielded cable is used, the shield must be connected at only one end of the cable. DO NOT connect a shield at both ends.

Standard Network Communication Connection

Warning:

The 12V N+ and N- communication input must be supplied from only one point. Connections from more than one 12V supply may cause failure or damage to the units supplying power.

Make sure that the power supply can supply enough current for the peak load drawn by all modules connected to the 12V supply, including the Controller itself.

The recommended module network wiring specifications are:

CAT5e / CAT6 are also supported for data transmission when using ground in the same cable.

24AWG twisted pair with characteristic impedance of 120ohm Belden 9842 or equivalent.

Maximum total length of cable is max 900m (3000ft)

Warning:

Unused wires in the cable must not be used to carry power to other devices.

The 330 Ohm EOL (End of Line) resistor provided in the accessory bag MUST be inserted between the NA and NB terminals of the first and last modules on the RS-485 network. These are the modules physically located at the ends of the RS-485 network cabling.

PRT-PSU-DIN orequivalent 12V DC

Shield is frame grounded atone point

Shields are connected togetherand Isolated

Shielded Cable

PRT-CTRL-DIN Network Module Network Module

Shielded Cable

Shield notconnected

NAN+ N- NBNAN+ N- NB NAN+ N- NB

supply


End of Line Resistors

3.3 Telephone Dialer The Protege DIN Rail Controller provides the ability to communicate alarms and upload information to remote systems using the onboard 2400bps modem. The telephone line can be connected directly to the Controller using the onboard telephone connection terminals.

Telephone Line Connection

330R 330R

NAN+ N- NB NAN+ N- NB

First Module on RS-485 Network Last Module on RS-485 Network

ToNext

Module

FromPreviousModule

R1iT1o

R1oT1i

Telco line out

Telco linetip and ring input

PRT-CTRL-

3.4 EThe communetwork opeKeypad term192.168.1.2networks.

Insthefix

When installlength) and

Temporary dEthernet por

i

DIN Protege

Etherneunication betwerating the TCminal or via th2 with a subn

stalling the Ce network. A

xed IP addres

ling an Ethernshould be co

direct connecrt.

GX DIN Rail

t 10/10ween the ProCP/IP protoche built in wenet mask of 2

Controller on aAlways consuss that can be

net connectioonnected to a

ctions can be

Integrated Sy

00 Netwotege Systemol suite. The b interface. T55.255.255.0

an active netwlt the networke assigned to

on the Controa suitable Eth

Ethernet 10/

e used for on

Ethernet

ystem Contro

work Intm and the Pro

IP address oThe default IP0. These IP a

work requiresk or system ao the Control

oller should bhernet hub or

/100 Switch hub

nsite program

10/100 Direct C

oller Installati

terfaceotege DIN Raiof the ControP address is saddress settin

s knowledge administratorler.

be interfaced r switch.

b Connection

mming by con

Connection

on Manual | M

l Controller uller can be coset to a staticngs are comm

of the configr and ask the

using a stand

necting direc

March 2012

uses a 10/100onfigured usic IP address monly used f

guration and sm to provide

dard segmen

ctly to the com

11

0 Ethernet ng the LCD of for internal

structure for e you with a

nt (<100m in

mputer

12

4 C

4.1 SThere are tw

If the currensettings theryour web brscreen.

The defa

The defa

PRT-CTRL

Config

Setting wo methods b

t IP is knownre. With the Crowser. Note

ault user nam

ault passwor

-DIN Protege

gurati

the IP Aby which the

n then the recController conthat the defa

me is admin.

rd is admin.

e GX DIN Rai

ion

AddresIP address o

commended nnected to yoault IP addres

Web

l Integrated S

ss of the Protege

method is toour network, ss is 192.168

interface login s

System Cont

e DIN Rail Co

o connect to ttype the curr

8.1.2. The we

screen

roller Installat

ontroller can

the built in werent IP addreseb browser w

tion Manual |

be set.

eb interface ass into the ad

will then displa

March 2012

and edit the ddress bar ofay a log in

2

f

PRT-CTRL-

Enter the us

Enter the req

4.2 SIf the currenkeypad.

Connect theInstaller codneed to forcpower cyclinwill erase all

Once loggedand Gatewa

Once the se

DIN Protege

ser name and

quired setting

Setting t IP address

e keypad to tde is 000000.ce the Controng the unit. Rl existing pro

d in select May as required

ettings have b

GX DIN Rail

d password a

gs, save them

the IP Aof the Contro

he module ne If the default

oller into its deRefer to the segramming as

enu 4 (Install d.

been changed

Integrated Sy

and the Contr

Built in w

m, and then r

Addresoller is not kn

etwork. Log t code has befault state. Tection on Has well as setti

Menu) then

d, you must

ystem Contro

roller Configu

web based conf

restart your C

ss from nown, it can b

in to the keypeen overriddThis is achievardware Confing up the de

Menu 2 (IP M

restart the Co

oller Installati

uration screen

figuration

Controller.

a Keypbe viewed an

pad using anen and you d

ved by connefiguration (seeefault Installer

Menu). View o

ontroller for t

on Manual | M

n is displayed

pad nd/or change

y valid Installdo not know tecting Readere page 36) for code.

or edit the IP

he settings to

March 2012

d:

ed using a PR

ler code. Thethe new codr 2 D0 to Rea

or details. Not

address, Net

o take effect.

13

RT-KLCD

e default es, you will ader 2 L and te that this

twork mask,

.

3

14

4.3 CTo connect

To add a

1. Login to

2. Click Ad

3. Select t

Addadd

Addand

Addprev

4. Once adserial nu

YoCo

i

PRT-CTRL

Configua Controller t

Controlle

o Protege GX

dd to display

he option tha

d controller wd the specified

d an individu other progra

d new controviously config

dded, the Coumber and co

ou may need ontrol Panel a

-DIN Protege

ring a Cto the softwa

er:

X and select S

the Add Con

at best suits y

with default rd expander m

al controlleramming must

oller based ogured Contro

ontroller will reommunicatio

to restart theand restart th

e GX DIN Rai

Controlare, you must

Sites > Cont

ntroller windo

your needs:

records (seemodules, doo

record: To at be added m

on an existingller.

equire confign parameters

e services to he Protege G

l Integrated S

ller via t add it to the

rollers from t

ow.

e page 15): Tors and group

add just the cmanually.

g controller

uration (see ps.

bring the coGX services.

System Cont

the Proe system pro

the main men

To add a singps as require

controller. An

(see page 16

page 17) to d

ntroller online

roller Installat

otege Ggramming.

nu.

gle Controller d by your site

ny expander m

6): To duplica

define setting

e. Select the

tion Manual |

GX Soft

r record and ae.

modules, doo

ate the progr

gs including th

services opti

March 2012

tware

automatically

ors, groups

ramming of a

he controller

on from the

2

y

a

PRT-CTRL-

Adding

If adding a Cautomaticallrecords can

General Name:

Name2that will software

Count: Controll

Controlle Inputs:

Controllthe onbdefault tinputs.

Outputscompatare assi1 is outpand doe

Add Troinputs wsection

DIN Protege

a Contr

Controller witly add the ex be edited lat

Defines the n

: Used to conbe used in re

e.

Defines the nlers are assig

er Defines the nler has only 8oard readersthe number o

s: The DIN raibility with oldgned sequenput #3 and Res not exist oouble Inputswill not be releon trouble in

GX DIN Rail

roller wi

h default recoxpander moduter on, delete

name of the C

nfigure the naeport genera

number of Cogned default n

number of on8 onboard inps then some oof inputs will b

ail Controller hder Controllerntial output n

Relay 2 is outpon the DIN Ras: Select this oevant to the D

nputs (see pa

Integrated Sy

th Defau

ords, the Addules, inputs, oed, and/or ad

Controller to b

ame that is dation if an Ope

ontrollers to bnames that c

nboard Contrputs, so the nof the inputs be set to 16

has 3 onboarr hardware anumbers 1 to put #4. Outpuail Controller.option to autDIN rail contrge 33).

ystem Contro

ult Reco

d Controlleroutputs and

dditional new

be used as a

displayed wheerator with th

be added. If mcan be edited

roller inputs thnumber selecmay be usedas older vers

rd outputs. Bnd should be4. On the DINut #2 is gene tomatically adroller and can

oller Installati

ords

configurationdoors that yorecords add

a reference w

en using an ahe Second La

more than ond later.

hat you intencted here shod for their reasions of the C

By default thee left set to foN Rail Contro

erated to main

dd the Contron later be dele

on Manual | M

n window is dour site will bed.

hen program

alternative lananguage optio

ne Controller i

d to use. Notould only be sader functionsController hard

e number of our. When the

oller the Bell ontain compat

oller trouble ineted. For furt

March 2012

displayed, enbe using. All o

mming the sys

nguage. This on selected l

is added, the

ote that the Dset to 8. If yos and not be dware have 1

outputs is sete outputs are output is outptibility with old

nputs. Somether details re

15

abling you toof these

stem.

is the name logs in to the

e subsequent

IN Rail u are using required. By

16 onboard

t to 4 for created they

put #1, Relayder hardware

e trouble efer to the

5

o

e

t

y

y y e

16

Keypads

Use these fieand the numthen it shouRefer to the

Device T Create

Create that def

Create Delay Foinput wi

Create a few in

Doors Doors: A

Expand

Assign Expandthe Rea

Assign to the Rdoor to door to

Assign Output

Adding

If adding a Cenabling you

Site (Co

Control

New Co

Prepenthe startis name

PRT-CTRL

s, Input E

elds to add tmber of inputsld be includeProgrammin

Type "All Menus"

Default Doofine how a do

Default InpuFollow Force,

ll operate in a

Floor Plan: Cputs and out

Automaticallyer.

to Reader Eer, the secon

ader One progReader Loc

Reader One lothe Reader Tthe Reader O

Reader Beeof the door p

a Contr

Controller basu to define ho

opy From): D

ler (Copy Fr

ontroller Nam

d Controller t of each rec

ed CTRL2, the

-DIN Protege

Expander

he relevant ns, outputs an

ed in the numng the Onboa

Menu Group

or Types: Creoor will opera

ut Types: CreTrouble Silenan area.

Create a flootputs. For larg

y creates the

Expanders: And door to thgramming of k PGM to Doock output onTwo lock outpOne lock outp

eper to Door programming

roller Ba

sed on an exow the new C

Defines the sit

om): Defines

me: Defines t

name to all ord name. Foe new door r

e GX DIN Rai

s, Reade

number of expnd trouble inpber of Reade

ard Reader (s

p: Creates a

eates 4 defaute (such as p

eates 10 defant, Trouble Be

r plan includiger sites it is

e defined num

Assigns the fire Reader Twthe second R

oor Configurn the first Reaput on the firsput on the se

Alarm Confito the assoc

ased on

xisting ControController and

te from which

s the Controlle

the name to b

record namor example, ifrecord would

l Integrated S

er Expand

panders that puts that will er Expanderssee page 29)

menu group

ult door typespassback and

ault input typeBell, Fire, Delay

ng all inputs generally bet

mber of door

rst door to thwo programm

Reader Exparation: Assigader Expandst Reader Ex

econds Read

iguration: Asciated beepe

an Exis

oller, the Copd associated

h the program

er from which

be assigned t

es: When enf a door reco be CTRL2 M

System Cont

ders, and

are connectbe used. Not

s so that progfor further de

called MG1

s -Card, Cardd reading mo

es - Instant, Iay Force, and

and outputs.tter to create

records. Typ

e Reader Oning of the firs

ander, etc. ns the Lock Oer, the Lock

xpander, the der Expander

ssigns the Prer on the asso

sting Co

py Controllerrecords will

mming should

h the program

to the new C

nabled, the naord is called MMain Entrance

roller Installat

Output E

ed to the mote that if the ogramming fieletails.

with every m

d and PIN, Caode

Instant Force24 Hour Ala

This is usefue the floor pla

ically this wo

ne programmst Reader Exp

Output progrOutput progrLock Output , etc.

e Alarm Outpociated Reade

ntroller

configurationbe created:

d be copied.

mming should

Controller.

ame of the coMain Entrancece.

tion Manual |

Expande

odule networkonboard readlds will be cre

menu enabled

Card or PIN, an

e, Delay, Delaarm- that defin

ul for small sitans manually.

ould be two p

ming of the firspander, the t

ramming of thramming of tprogrammin

put and Left Oer Expander.

n window is d

d be copied.

ontroller will bce and the new

March 2012

rs

k of the site, der is used eated for it.

d.

nd PIN only -

ay Follow, ne how an

tes with only

per Reader

st Reader hird door to

he first door the second g of the third

Open Alarm .

displayed,

be added to w Controller

2

-

d

PRT-CTRL-

Add Accontaini

Copy G

Configu

Once addedcommunicat

Control

General Name:

name shthe IP a

Record

Identifica Panel ID

Host ID

Serial N

Commun IP Addr

valid TC

DIN Protege

ccess Level aing all doors,

Global Recor

uring a C

d, the Controtion paramet

llers | Ge

The Controllehould describnd SMTP Ma

Group: Ena

ation D: The panel

D Code: The

Number: The

nicationsress: The sys

CP/IP Addres

GX DIN Rail

and Door Grand an acce

ds: When en

Controlle

oller needs to ers.

eneral S

er name is prbe the premisail Services to

ables you to d

ID code for t

host ID code

serial numbe

s stem controlles to allow the

Integrated Sy

roup: When eess level cont

nabled, copie

er

be configure

Settings

rogrammed tses or the buo identify the

define which r

the controller

e for the cont

er of the cont

er has a builte software to

ystem Contro

enabled, creataining this do

es the global r

ed to define s

to identify theuilding where

panel to the

record group

r.

roller.

troller.

t in TCP/IP Eto connect. By

oller Installati

ates a door goor group.

records that

settings includ

e panel to thethe panel is ie-mail recipi

p the controlle

thernet Devicy default the I

on Manual | M

roup (using t

are relevant t

ding the cont

e operator or nstalled. Theent.

er belongs to

ce and it musP address is

March 2012

the Controller

to the origina

troller serial n

system usere name is also

o.

st be programset to 192.1

17

r name)

al Controller.

number and

. Ideally the o used within

mmed with a 68.1.2.

7

n

18

Programconnect

IP Port: Downlo

Controlis port 2

Last Kn(Read o

Last Do

Display Default

are first owners

Default are first owners

Panel Nconnect

Control

Configur Test Re

test repbetween

Automamodules

AC Resbe pres

PRT-CTRL

mming an IP ated to. ALWA

: When connoad Server: D

and Status 21001.

nown IP Addonly)

ownloaded: S

Display Lineconnected todetails.

Display Lineconnected todetails.

Name: The deted to the sys

llers | Co

ration eport: The teort trouble inn reports in h

atic Offline Ts at a set tim

store Delay Tent for after a

-DIN Protege

address requAYS consult t

ecting to theDefines the d

Request Po

dress: Shows

Shows the da

e One: The do the system

e Two: The do the system

efault LCD pastem.

onfigura

st report timeput activates

hours and min

Time: Allows tme of the day.

Time (secondan AC Failure

e GX DIN Rai

uires knowledthe network o

controller usownload serv

ort: The IP po

s the last IP a

ate and time

default LCD tem. This text sh

default LCD tem. This text sh

anel name th

ation Set

e in conjuncts. When optionutes.

the panel to u

ds): The AC Re before resto

l Integrated S

dge of the neor system ad

sing TCP/IP, ver used by t

ort through wh

address that t

of the last do

ext for line onhould be chan

ext for line twhould be chan

hat is shown o

ttings

ion with optioon 2 is disabl

update the u

Restore time oring the AC

System Cont

twork and sudministrator b

this specifiesthe controller

hich control c

the controller

ownload. (Re

ne is shown onged to the n

wo is shown onged to the n

on all PRT-K

on 2 sets theed the time p

sers and othe

allows the insFailure Troub

roller Installat

ubnet that theefore program

s the IP port t.

commands w

r communica

ead only)

on all PRT-KLname of the b

on all PRT-KLname of the b

LCD keypads

time of the dprogrammed

er offline para

staller to progble Input. Set

tion Manual |

e system conmming these

to use.

will be sent. B

ated to the se

LCD keypadsbuilding, insta

LCD keypadsbuilding, insta

s when they

day or the pe will be used

ameters on a

gram a time tt this to a larg

March 2012

ntroller will bee values.

By default this

erver on.

s when they allation or

s when they allation or

are first

eriod that the as a period

all intelligent

that AC mustger value for

2

e

s

t


locations that experience frequent but short interruptions in power or that operates on a generator frequently.

AC Fail Time (Seconds): The AC Failure time allows the installer to program a time that AC mains voltage must have failed before activating the AC Failure Trouble Input. Set this to a larger value for locations that experience frequent but short interruptions in power or that operates on a generator frequently.

Battery Test Time (Minutes): The battery test time allows the installer to program the duration of time in minutes between each battery test that is performed. A battery test is performed immediately on power up of the panel and then every programmed period. Each battery test takes 45 seconds and the battery low/failure trouble input will activate if the battery fails.

Module UDP Port: This is the UDP port that all Ethernet enabled modules will communicate with the Protege System Controller over. If this port is changed all modules will need to also be changed.

Modem Country: The onboard modem must be configured for the region that the System Controller is being installed in to ensure proper operation.

Modem Backup Phone Number: If Ethernet communication fails, the modem will dial this number to report events.

Default Language: The System Controller supports multiple languages on the Keypad and the Serial Event Printers. The language selected here will be the default language for users who have no language selected and also for any events.

Download Retry Delay: Defines the frequency (in seconds) at which the software sends updates to the controller.

Register as Reader Expander: Used for programming the onboard reader. By default the onboard reader is registered as the last reader in the defined profile (for example, Reader Expander 008 in the standard profile). This means that if a reader expander is connected with the same address, it will be treated as a duplicate and fail to register. To change the address, select an alternative reader expander from the dropdown.

Onboard Reader Lock Outputs: Defines the output that will be activated upon successful door access. If set to none, the normal door output is used.

Touchscreen UDP Port: The UDP port that a touchscreen will communicate over.

Encryption Initialize Panel Encryption: Will enable encryption of the messages sent between the controller and the

Protege GX software. Note that when a controller is in its default state, encryption is turned off. Selecting this option performs a one-off process that randomly generates and begins using an encryption key (256 bit AES). Using an RSA algorithm, this key is exchanged and stored in both the controller and the GX database. If a controller is to be moved from one site to another, it must be returned to its default state (by powering up with dip switch 4 turned on) to reset the encryption setting to off. A defaulted controller will not communicate with software that has encryption turned on, and you must select this option again to create a new encryption key.

Encryption Enabled: Read only field that indicates if encryption is enabled.

20

Control

Options Genera

the spec

Troubleuntil a u

Generaevent foactivate

Log Assoccur. Afunction

Login Uname ththat mu

Misc Op Enable

configur

Modemto the soautomat

Backupsoftwarereducesevents a

Invert Callowing

Log All Manage

Treat Uthe user

PRT-CTRL

llers | Op

ate Periodic (cified frequen

es Requires Auser logs in th

ate Input Resor the trouble ed.

sertion ErrorAn assertion en that results

User Code Nhat is providest log in to th

ptions Automatic Oration parame

m Backup if Ioftware via Etically switch

p Only Alarme via the mods the amount are sent via E

Controller Tag a normally o

Access Levement Suite.

ser PIN plusr pin 1234 is

-DIN Protege

ptions S

(Minutes) Tency.

Acknowledghe keypad an

store On Tesinput test re

rs: When enaevent is genein a condition

ot Requireded from the rehe system.

Offline Downeters to all R

P Fails: Whethernet. If the back to Ethe

m Events: If thdem, then thiof traffic and

Ethernet so th

amper Input: open (door cl

el Events: W

s 1 as Duressentered as 1

e GX DIN Rai

Settings

st Report: W

ge: When enand acknowled

st Report Inpport input res

abled the syserating when n that is not d

: When enabemote Proteg

load: When DI modules a

en selected the Ethernet coernet.

he Ethernet lins option can

d improves thhis option doe

When enableosed) tampe

When enabled

s: When enab235, it is pro

l Integrated S

When enabled

abled any trodges the trou

put: When enstoring. This o

stem controllethe system c

deemed norm

bled the systege System M

enabled the at the time pr

he Controller onnection is s

nk has failed be selected

he response tes not mean

ed the systemer switch to b

d the controlle

bled, treats aocessed as a

System Cont

d the test rep

uble conditioble condition

nabled the syoccurs one m

er will log opecontroller getmal.

em controller anagement S

system contrrogrammed in

will dial out tsubsequently

and the Conto only send

time. When ththat any eve

m controller wbe used.

er will upload

a users pin pluduress code

roller Installat

port trouble in

on will be latcn.

stem controlminute after th

erating systems a value, co

will not validaSuite or other

roller will auton the Offline U

hrough a morestored, the

ntroller is com reportable ehe Ethernet li

ents will be los

will invert the

all events to

us 1 as a dure.

tion Manual |

nput will be ac

hed and rem

ller will generhe trouble inp

m assertion eommand or p

ate the login r remote hos

omatically upUser Update

odem if it cane communica

mmunicating wevents via moink is restorest.

module tam

o the Protege

ress code. Fo

March 2012

ctivated at

main active

ate a restoreput has been

events that erforms a

and user t systems

pdate offline Time.

not connect ation path will

with the odem. This d ALL stored

per input

e System

or example, if

2

n

l

d

f

PRT-CTRL-

Antipass Reset A

schedul

Enable Time an

Antipassetting a

Control

Automathe cont

Primary

Secondshould i

Time Zo

DIN Protege

sback Antipassbackle.

Timed User nd Exit User Rssback Reseabove, this o

llers | Tim

atically Synctroller with an

y SNTP Time

dary SNTP Tt not be able

one: The cur

GX DIN Rail

k Status on

AntipassbacReset Time s

et Schedule: ption defines

me Upd

hronize withn internet tim

e Server: The

Time Server: e to connect t

rrent time zon

Integrated Sy

schedule: W

ck Reset: Wettings define

Used in conjs the schedul

date Sett

an Internet e server.

e primary SN

The secondato the primary

ne that should

ystem Contro

When enabled

When enableded in the doo

junction with e used to res

tings

Time Server

TP time serv

ary SNTP timry SNTP serv

d be assigne

oller Installati

d, resets the a

, anti-passbaor programmi

the Reset Anset anti-pass

r: Select this

ver for the con

me server for ter.

ed to the cont

on Manual | M

anti-passbac

ack is reset usng.

AntiPassback Sback status.

option to aut

ntroller to upd

the controller

troller. Offset

March 2012

ck status usin

sing the Entr

k Status on sc

tomatically sy

date it's time

r to update it

from GMT.

21

ng a defined

ry User Reset

chedule

ynchronize

e from.

's time from

t

22

Control

Custom Custom

Magnet

Bit Lengbadge.

Site Cotransmit

Site CoThe cou

Card Ntransmit

Card Ntransmit

Data FoIf the sizuse 16 b

PRT-CTRL

llers | Cu

Reader Cm Reader Typic Data (Cloc

gth: The bit l

ode Start: Thtted. The cou

ode End: Theunt starts at z

umber Starttted. The co

umber End: tted. The coormat: The daze of the site bit, otherwise

-DIN Protege

ustom R

Configurape: Defines t

ck and Data).

ength defines

e site code sunt starts at ze site code enzero.

: The card nuount starts at

The card nuount starts atata format decode and cae use 32 bit.

e GX DIN Rai

Reader F

ation he reader typ

s the total nu

start defines tzero. nd defines the

umber start dt zero.

mber end det zero. efines how thrd number arIf unsure, use

l Integrated S

Format S

pe. The data

umber of bits

the index whe

e index wher

defines the in

efines the inde

he card numbre less than 1e 32 bit.

System Cont

Settings

can either be

that are sent

ere the site c

re the site cod

dex where th

ex where the

ber that is rec6 bits (e.g. S

roller Installat

s

e output as W

t by the card

ode data sta

de data ends

he facility cod

e facility code

eived from thSite Start – Sit

tion Manual |

Wiegand (D0

reader for ea

arts in the dat

s in the data t

de data starts

e data end in

he card readete End is less

March 2012

and D1) or

ach card

ta

transmitted.

s in the data

the data

er is handled.s that 16 bits)

2

. )


Parity Options (1-4)

There can be up to 4 blocks of parity calculated over the received data.

Parity Type: The parity type defines the method of calculating the parity for the block. This is either Even or Odd Parity.

Parity Location: The parity location defines where the location of the parity bit in the received data. Parity Start: Defines where the location of the parity block starts in the received data.

Parity End: Defines where the location of the parity block ends in the received data.

Bit Options (1-4) Set Bit: A set bit defines a location in the received data that must always be set (or a logical '1'). The set bit

defines where the location of the bit in the received data.

Clear Bit: A clear bit defines a location in the received data that must always be cleared (or a logical '0'). The clear bit defines the location of the bit in the received data.

4.4 Addressing Modules Traditionally the network address of a module has been set using a bank of DIP Switches located on each individual module. The DIN Rail modules enable addresses to be configured electronically via the Protege GX software.

The factory default address of all DIN Rail mount modules is 254 and without changing this address they will not be able to register with the Controller.

To change the network address of a module:

1. Ensure the Controller is correctly powered and is communicating with the Protege GX software. Refer to Protege GX software documentation for more information about the software configuration.

2. Connect the module(s) that require addressing to the module network. Make sure that the Power light on each module is on and that the Status light begins flashing rapidly.

3. Allow some time for the module(s) to attempt to register with the Controller.

i

24

If thwill

If ththe

4. Once alwindow

The Aut

5. If the adselectorwhich mperiod othe softw

6. Enter anaddressupdatedAllow ab

7. Click Reshow th

If thatte

If thadd

Once al

PRT-CTRL

e module habegin flashin

e module hasStatus light w

l modules haw in the softwa

to- Addressin

ddress can ber in the Addremodule is whiof time. Moduware. Ensure

n address fors has been sed individually bout 5 secon

efresh to updhat they have

e address haempting to reg

e address hadress range a

l modules are

-DIN Protege

s the default g at 1 secon

s been previowill begin flas

ave completeare by right c

ng window op

e changed eless column isch, click Find

ules can also e that you are

r the relevant elected but hby clicking th

nds per modu

date the list a been read b

as not changegister.

as changed band that it is n

e online and

e GX DIN Rai

address of 2d intervals.

ously addresshing at 1 sec

d the registraclicking on the

pens:

ectronically ts enabled. Thd to instruct tbe identified

e clear which

modules by as not yet be

he option in tule for the new

and display thback from the

ed, check the

but the modunot a duplicat

registered wi

l Integrated S

254 or has th

sed and is nocond intervals

ation processe Controller a

this is indicatehe Update anthe respectiv by comparinmodule is w

selecting an een updated the Update cow address to

he new addree Controller.

e module is o

ule is not showte of another

ith the desire

System Cont

e same addr

ot a duplicates.

s (successful and selecting

ed in the Addnd Find optionve module to ng the serial n

which before a

option from on the moduolumn, or all

o be sent and

esses. The ad

online and co

wn as registemodules add

ed addresses

roller Installat

ess as anoth

e then it will s

or not), openg Auto Addre

dress can be ns will also beflash its Statu

number on thassigning add

the Address ule, it is showat once using

d registered.

ddresses cha

ommunicating

ered, check thdress.

, the address

tion Manual |

her module, th

succeed in re

n the Auto-adess.

e changed cole enabled. If us light for th

he label with tdresses to th

s column. Whewn in red. Mod

g the Update

ange from red

g and that is

he address is

sing process

March 2012

he Fault light

gistering and

ddressing

lumn and theit is not clear

he specified that shown inem.

en an dules can bee All button.

d to grey to

has finished

s in the valid

is complete.

2

d

e r

n

e


5 Door Access Control

The Protege DIN Rail Controller provides access control functionality onboard without the requirement for additional hardware. The Controller allows the connection of two Wiegand devices to control two doors (entry or exit only) or it can be configured in multiplex mode to allow four Wiegand devices controlling two doors giving the flexibility of entry and exit readers.

The beeper output of the Controller provides diagnostic information to the end user and installer when access is denied or the card format is incorrect.

Warning:

The card reader must be connected to the Controller port using a shielded cable.

Always refer to the card reader manufacturer for detailed installation guidelines.

The shield connection must only be connected at one end of the cable in the metallic enclosure (frame grounded).

Do not connect the shield to a V- connection on the Controller. Do not join the shield and black wires at the reading device.

Do not connect the shield to any shield used for isolated communication.

The Controller does not support dual LED reader mode and readers must be configured for single LED mode. Refer to your card reader documentation for further details.

5.1 Card Reader Connection The following diagram shows the connection of a standard Wiegand Reader with the Protege DIN Rail Controller controlling an access door in entry or exit mode (2 doors, 2 readers).

Card Reader Connection

i

Shield is frame grounded at

one point

Shielded Cable

RED

BLACK

GREEN

WHITE

ORANGE

BROWN

BLUE

YELLOW

SHIELD

N/R

N/R

Shield notconnected

V+V-Z4 V- Z3 Z2 V- Z1BZ L1 D1 DO


5.2 Multiple Wiegand Card Reader Connection When operating the Protege DIN Rail Controller in multiple reader mode, the Controller allows the connection of 4 Wiegand reading devices controlling two doors each with entry/exit readers.

When connecting Wiegand readers in multiple reader mode, the secondary reader that is connected will have all connections wired to the same port as the primary card reader with the DATA 1 connection wired to the opposite reader connection DATA 1 input.

Multiple Wiegand Card Reader Connection

Shield is frame grounded at

one point

Shielded Cable

Shielded Cable

RED

BLACK

GREEN

WHITE

ORANGE

BROWN

BLUE

YELLOW

SHIELD

N/R

N/R

RED

BLACK

GREEN

SHIELD

WHITE

ORANGE

BROWN

BLUE

YELLOW

N/R

N/R

Shield notconnected

V+V-Z4 V- Z3 Z2 V- Z1BZ L1 D1 DOBZ L1 D1 DO


5.3 Door Contact Connection The Protege DIN Rail Controller allows the connection of up to 4x contacts for monitoring and controlling access control doors. Each input on the Controller can be used for the door function that is automatically assigned and as a normal input on the system. The following example shows the connection of a normally closed door position monitoring contact to monitor the Open, Closed, Forced and Alarm conditions of the door.

Door Contact Connection

Inputs 1-4 and 5-8 can operate as either general purpose inputs or as onboard reader inputs. If used as general purpose inputs, make sure that these inputs are not defined in the onboard reader set up.

Input Access Control Function Default Setting

Input 1 Door Contact, Port 1 Door Contact, Port 1

Input 2 REX Input, Port 1 REX Input, Port 1

Input 3 Bond Sense, Port 1 General Purpose Input

Input 4 REN Input, Port 1 General Purpose Input

Input 5 Door Contact, Port 2 Door Contact, Port 2

Input 6 REX Input, Port 2 REX Input, Port 2

Input 7 Bond Sense, Port 2 General Purpose Input

Input 8 REN Input, Port 2 General Purpose Input

When connected, the REX Input can be programmed to operate regardless of the door contact state. The REX input can also be programmed to recycle the door alarm time to prevent nuisance alarms when the door is held open to permit longer entry.

V+V-

Z4V-

Z3Z2

V-Z1

N.C. Input Contact

N.C. Input Contact

N.O. Input Contact

N.O. Input Contact

1K

1K

1K

1K

1K

1K 1K

1K

Door Contact

Bond Sense

REN Input

REX Input

i


5.4 Lock Output Connection The Protege DIN Rail Controller provides a connection for an electric strike lock with full monitoring of the lock circuit for tamper and over current/fuse blown conditions. The door lock monitoring can be disabled if it is not required.

The lock output is shared with the bell/siren function as shown in the diagram below. You can select another output for the lock control (Relay 1 (CP001:03) or Relay 2 (CP001:04)) if the bell/siren function is required. To use the lock outputs in conjunction with the onboard reader module, the Lock output for the door associated with the reader port must be configured to be the desired lock output on the controller. This is not configured by default.

Lock Output Connection

When using a door with an Entry and Exit Reader, the lock output should be connected to the Bell (CP001:01), and the swap lock option for the second reader input should be enabled to allow the reader LEDs to display the correct status.

The Bell output current must not exceed 1.1A or electronic shutdown will be engaged. Ensure the devices connected to the outputs are within the limits as detailed in the Technical Specifications (see page 42).

+

-

1N4007 Diode

12VDC ElectricLocking Device

B+B-

COM

NOCO

MNO

i

PRT-CTRL-

5.5 PThe onboardas if it were disabled. To(under the Sconnected wensure the a

The onboardAny of theseinputs. If thedisable the a

The default

Input

Input 1

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7

Input 8

DIN Protege

Programd reader is pra normal rea

o enable it, coSites > Controwith the sameaddress is un

d reader usese inputs that e onboard reaassociated fu

settings are s

GX DIN Rail

mming trogrammed i

ader expandeonfigure the aollers programe address wi

nique.

s inputs 1-4 aare not confiader is enableunction input

shown in the

Acces

Door Co

REX Inp

Bond S

REN Inp

Door Co

REX Inp

Bond S

REN Inp

Integrated Sy

the Onbn exactly the

er module on address at wmming tab). Nll be treated a

and 5-8 as itgured for useed and you win the Reade

following tab

s Control F

ontact, Port 1

put, Port 1

ense, Port 1

put, Port 1

ontact, Port 2

put, Port 2

ense, Port 2

put, Port 2

ystem Contro

board Re same way a

a separate chich you wanNote that anyas a duplicate

s door contae with the onwish to use ser Expander p

ble:

Function

1

2

oller Installati

Readeras any other rcircuit board. nt it to registey physical reae and will fail

act, REX, bonboard readerome of theseprogramming

De

Do

REX

Ge

Ge

Do

REX

Ge

Ge

on Manual | M

r reader modulBy default th

er using the Pader expandeto register so

nd sense andr may be usee as general ig section of th

efault Settin

or Contact, P

X Input, Port

neral Purpos

neral Purpos

or Contact, P

X Input, Port

neral Purpos

neral Purpos

March 2012

le is. It can bhe onboard reProtege GX ser module thao care should

d REN inputs ed as generalnputs, you whe Protege G

ng

Port 1

1

se Input

se Input

Port 2

2

se Input

se Input

29

e thought of eader is software at is d be taken to

respectively. purpose

will need to GX software.

9

o

30

PRT-CTRL-DIN Protegee GX DIN Rai

Reade

l Integrated S

er Expander Pro

System Cont

operties

roller Installattion Manual | March 2012

2


6 Inputs

6.1 Onboard Inputs The Protege DIN Rail Controller has 8 onboard inputs and monitors up to 64 trouble inputs used to report trouble conditions within the system. The trouble input will open or go in to alarm when that trouble condition is present, and close or return to normal when the trouble condition is restored.

The Controller can monitor and control thousands of additional inputs and trouble inputs by using the expansion modules.

The Controller can monitor the state of up to 8 onboard inputs such as magnetic contacts, motion detectors and temperature sensors. Devices connected to these inputs can be installed to a maximum distance of 300m (1000ft) from the Controller when using 22 AWG. The Controller supports normally opened and normally closed configurations with or without EOL resistors.

Inputs can be programmed using the Protege GX software. Inputs CP001:01 to CP001:08 represent the Controller's onboard inputs.

When using an input with the EOL resistor configuration, the Protege DIN Rail Controller generates an alarm condition when the state of an input is toggled and generates a tamper alarm condition when a wire fault (short circuit) or a cut (tampered) in the line occurs.

Inputs default to require the EOL resistor configuration.

EOL Resistor Input Configuration

Inputs 1-4 and 5-8 can operate as either general purpose inputs or as onboard reader inputs. If used as general purpose inputs you must ensure that they are not defined in the onboard reader set up.

Each input can use a different configuration. To program a large number of inputs with a certain configuration, use the multiple selection feature within the Protege GX software.

N.C Input Contact

N.C Tamper 1K 1K

V+V-

Z4V-

Z3Z2

V-Z1

i


When using the No Resistor configuration, the Controller only monitors the opened and closed state of the connected input device generating the alarm and seal conditions.

No EOL Resistor Input Configuration

6.2 Resistor Value Options When using the EOL resistor configuration, the EOL resistor option must be configured based on the site requirements. Note these resistor options are supported on the PRT-CTRL-DIN Controller but not all resistor options are supported on all Protege field modules.

Value 1 Value 2 Monitored Status

1k 1k Open, Closed, Tamper, Short

1k - Open, Closed

<5K7 - Open, Closed

No Resistors - Open, Closed

2k2 6k8 Open, Closed, Tamper, Short

10k 10k Open, Closed, Tamper, Short




N.C Input Contact

V+V-

Z4V-

Z3Z2

V-Z1


6.3 Trouble Inputs Each Protege DIN Rail Controller can monitor up to 64 local trouble inputs. Trouble inputs are used to monitor the status of the Controller and in most cases are not physically connected to an external input. These can then be used to report a message to a monitoring station, remote computer, keypad or siren.

The following table details the trouble inputs that are configured in the Controller. The trouble type and group define the trouble that is generated by the trouble input when it is activated.

Input Number Description Type Group CP001:01 Reserved - -

CP001:02 12V supply failure Power Fault General

CP001:03 Reserved - -

CP001:04 Real Time Clock Not Set RTC/Clock Loss General

CP001:05 Service Report Test - -

CP001:06 Service Report Failure to Communicate Reporting Failure General

CP001:07 Phone Line Fault Phone Line Lost General

CP001:08 Auxiliary Failure Power Fault General

CP001:09 Bell Cut/Tamper Bell/Output Fault General


CP001:11 Bell Current Overload Bell/Output Fault General


CP001:13 Module Communication Module Loss System

CP001:14 Module Network Security Module Security System






CP001:20 Ethernet Link Lost Hardware Fault System


CP001:22 ModBUS Communication Fault Hardware Fault System

CP001:23 Protege System Remote Access Hardware Fault System

CP001:24 Installer Logged In Hardware Fault System





CP001:29 System restarted Hardware Fault System


| | | | | | | |



7 Outputs

The Protege DIN Rail Controller has 7 onboard outputs. Outputs are used to activate sirens, bells, warning devices, control lighting and doors. The first output on the Controller has a special hardware design that allows it to monitor for fault conditions and is ideally suited to driving sirens or warning devices.

7.1 Bell/Siren Output The + and - terminals of the Bell output (CP001:01) are used to power bells, sirens or any devices that require a steady voltage output. The bell output supplies 12VDC upon alarm and supports one 30-watt siren. The bell output uses an electronically fused circuit and automatically shuts down under fault conditions.

Bell Siren Connection

If the load on the bell terminals returns to normal, the Controller reinstates power to the bell terminals on the next transition of the output.

When the bell output is not used, the appropriate trouble input (see page 33) will be activated. This can be avoided by connecting a 1K resistor (provided in the accessory bag) across the bell output. If the bell is not being used for another function, and the trouble input is not programmed in the system, a resistor is not required.

Connecting a Piezo siren may result in a dull noise being emitted. This is caused by residual current from the monitoring circuit. To prevent this occurring, connect 2 1K resistors in parallel.

+

-

12VDC siren warning device

1k Resistors

B+B-

COM

NOCO

MNO

i


7.2 Relay Outputs The Relay Outputs (CP001:03 and CP001:04) on the Protege DIN Rail Controller are normally open relay outputs. These outputs can be used to activate larger relays, sounders and lights, etc.

Example Relay Connection

Warning: The Relay outputs can switch to a maximum capacity of 7A. Exceeding this amount will damage the output.

7.3 Reader Outputs If readers are not attached to the reader ports then the Reader 1 L1 and BZ, and the Reader 2 L1 and BZ outputs can be used as general purpose outputs. These can be controlled by assigning the RDxxxGreen R1, RDxxx Beeper R1, RDxxxGreen R2 and RDxxx Beeper R2 outputs of whichever reader module has been configured as the onboard reader module. These are open drain outputs which switch to the V- reference.

Open Drain Reader Outputs

Warning: The reader outputs can switch to a maximum capacity of 50mA. Exceeding this amount will damage the output.

LED

B+B-

COM

NOCO

MNO

V+V-

Z4V-

Z3Z2

V-Z1

1K5 OHM

BZL1

D1DO

LEDV+V-

Z4V-

Z3Z2

V-Z1

1K5 OHM


8 Hardware Configuration

8.1 Defaulting a Controller The Protege DIN Rail Controller can be set back to factory default using the following procedure. This resets all internal data and event information.

To default a controller:

1. Remove power from the Controller by disconnecting the 12V DC input.

2. Connect a wire link between Reader 2 D0 input and Reader 2 L1 output.

3. Power up the Controller.

4. Once the Controller has started and the Status light is flashing, remove the wire link from the Reader 2 connector. The system will now be defaulted with all programming and settings returned to factory configuration.

Defaulting the Controller does not reset the IP address. Refer to Setting the IP Address (see page 12) for instructions on how to reset the address.

BZ L1 D1 DO

i

PRT-CTRL-

9 L

The DIN Raidiagnosing fstatus indica

9.1 PThe Power i

Please note

State

9.2 SThe Status i

State

9.3 FThe Fault indoperation th

State

DIN Protege

LED In

il Controller infaults and coator display a

Power Indicator is lit

that this indi

ON

OFF

Status Indicator disp

F

Fault Inddicator LED i

he fault indica

GX DIN Rail

ndica

ncludes comonditions. In sat the time.

ndicatot when the co

cator may ta

ndicatoplays the stat

lashing at 1 s

dicator s lit any time

ator is off.

OFF

ON

Integrated Sy

ators

prehensive frsome cases a

or orrect input v

ake several se

Des

Corre

Incor

or us of the Con

second interv

the Controlle

Des

Cont

Cont

ystem Contro

ront panel diaan indicator m

voltage is app

econds to ligh

scription

ect input volt

rrect input vo

ntroller.

D

vals Th

er is operatin

scription

troller is oper

troller is oper

oller Installati

agnostic indicmay have mu

plied to the C

ht up after po

tage applied

oltage applied

Description

he Controller

g in a non-st

rating normal

rating in a non

on Manual | M

cators that caltiple meanin

ontroller.

ower has bee

d

is operating

tandard mode

ly

n-standard m

March 2012

an aid the insgs dependin

en applied.

normally

e. During nor

mode

37

staller in g on the

rmal

7


9.4 Ethernet Link Indicator The Ethernet indicator shows the status of the ethernet connection.

State Description

ON Valid link with a hub, switch or direct connection to a personal computer detected

OFF Ethernet cable not connected, no link detected

9.5 Modem Indicator The Modem indicator shows the status of the onboard modem.

State Description

ON Modem has control of telephone line

OFF Modem is not active

9.6 R1/R2 Reader Data Indicators The R1 and R2 indicators display the status of the data being received by the onboard readers.

State Description

Short Flash

A short FLASH (<250 Milliseconds) will show that data was received but was not in the correct format.

Long Flash

A long FLASH (>1 Second) indicates that the unit has read the data and the format was correct.

9.7 Bell Indicator The Bell indicator shows the status of the bell output and the over current or circuit fault conditions.

State Description

OFF Bell is connected, output is OFF

ON Bell is ON

Two flashes Bell is ON, the circuit is in over current protection

Three flashes

Bell is OFF, the circuit to the siren/bell is cut, damaged or tampered


9.8 Relay Indicators The Relay 1 and Relay 2 indicators show the status of the lock output relay.

State Description

On Relay output is ON

Off Relay output is OFF

9.9 Zone (Input) Indicators Whenever an input on the DIN Rail Controller is programmed with an input type and area, and that area is armed, the input status is displayed on the front panel (indicators 1-8) corresponding to the physical input number (Z1-Z8). This allows easy walk test verification of inputs without the need to view the inputs from the keypad or Protege software.

State Description

On (Red) Input is in an OPEN state

On (Green) Input is in a CLOSED state

Flashing (Red) Input is in a TAMPER state

Flashing (Green) Input is in a SHORT state

11

1 1 1

1 1 1


10 Mechanical Diagram

The mechanical diagram shown below outlines the essential details needed to help ensure the correct installation of the DIN Rail Controller.

Input Status

Inputs 1 to 4Reader Port

RS-485 Input

Reader Port

Ethernet Interface

Status IndicatorsBell/Relay Outputs

Inputs 5 to 8

12VDC Input

Status Indicators

Panel Modem Interface


11 Mechanical Layout

The mechanical layout shown below outlines the essential details needed to help ensure the correct installation of the DIN Rail Controller.

156.8mm

143.5mm

36.4

mm

90m

m

90m

m

156.8mm

PRT-CTRL-DIN FRONT

44.1

mm

PRT-CTRL-DIN BACK


12 Technical Specifications

The following specifications are important and vital to the correct operation of the Protege DIN Rail Controller. Failure to adhere to the specifications will result in any warranty or guarantee that was provided becoming null and void.

Integrated Control Technology continually strives to increase the performance of its products. As a result these specifications may change without notice. We recommend consulting the ICT website (http://www.incontrol.co.nz) for the latest documentation and product information.

Operating Voltage 12V DC +- 10%

Operating Current 120mA (Typical)

DC Output (Auxiliary) 0.7A (Typical) Electronic Shutdown at 1.1A

Bell DC Output (Continuous) 8 Ohm 30W Siren or 1.1A (Typical)

Bell DC Output (Inrush) 1500mA

Total Combined Current* 3.4A (Max)

Electronic Disconnection 9.0VDC

Communication (Ethernet) 1 10/100Mbps Ethernet Communication Link

Communication (Serial) 1 RS-485 Communication Interface Port

Communication (Modem) 1 2400bps Modem Communication

Readers (Standard Mode) 2 Wiegand or clock data readers providing one Entry/Exit Door or two Entry/Exit only Doors

Readers (Multiplex-reader Mode)

4 Wiegand Readers (connected in Multiplex Reader mode) providing any combination of Entry or Exit for two Doors

Inputs (System Inputs) 8 High Security Monitored Inputs

Outputs 4 50mA (Max) Open Collector Output for reader LED and beeper or general functions

Relay Outputs 2 FORM A Relays - 7A max

Operating Temperature 0˚ to 49˚C (32˚ to 122˚F)

Storage Temperature -10˚ to 85˚C (14˚ to 185˚F)

Humidity 0% to 85% non condensing, indoor use only (Relative Humidity)

Dimensions (L x W x H) 156 x 90 x 60mm (6.14 x 3.54 x 2.36")

Weight 376g (13.26oz)

The size of conductor used for the supply of all power to the Protege DIN Rail Controller should be adequate in size to prevent voltage drop at the terminals of no more than 5% of the rated voltage. Specifications are subject to change without notice, please visit www.incontrol.co.nz for updated information.

* The Total Combined Current refers to the current that will be drawn from the external power supply to supply the Controller itself as well as any devices connected to the outputs of the Controller. The Auxiliary outputs and Bell output are directly connected via electronic fuses to the N+ N- input terminals, and the maximum current is governed by the trip level of these fuses.


12.1 Current and Validation Example The example shown below refers to the specifications needed to help ensure the correct installation of the Protege DIN Rail Controller. Specifications should be validated to ensure that individual maximum currents and total combined current are not exceeded.

Example

External Devices Connected to Panel

4 EDGE PIR Motion Detectors (Z1 to Z4) connected on AUX1 Output

4 EDGE PIR Motion Detectors (Z5 to Z8) connected on AUX2 Output

1 30W Siren (1.1A (1100mA) @ 13.8VDC)

Current Consumption

Total Combined Current before shutdown 3.4A (3400mA)

Operating Current 120mA (Typical)

DC Output (AUX1) 4 EDGE PIR Motion Detectors @ 15mA each (Total 60mA)

DC Output (AUX2) 4 EDGE PIR Motion Detectors @ 15mA each (Total 60mA)

Siren on Bell Output 1.1A (1100mA)

Total Consumption 1.34A (1340mA)

Validation

Is the total DC Output (AUX1) current less or equal to 1.1A (1100mA)? Yes, it is 60mA

Is the total DC Output (AUX2) current less or equal to 1.1A (1100mA)? Yes, it is 60mA

Is the Bell current output less or equal to 1.1A (1100mA)? Yes, it is 1.1A (1100mA)

Is the total combined current less or equal to 3.4A (3400mA)? Yes, it is 1.34A (1340mA)


13 Ordering Information

Please use the following product codes when placing an order for the Protege GX DIN Rail Integrated System Controller.

PRT-CTRL-DIN

Manuals and additional literature are available on the ICT Website (http://www.incontrol.co.nz) under the Support section.


14 Warranty

Integrated Control Technology (ICT) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. ICT does not install or connect the products and because the products may be used in conjunction with products not manufactured by ICT, ICT cannot guarantee the performance of the security system. ICT's obligation and liability under this warranty is expressly limited to repairing or replacing, at ICT's option, any product not meeting the specifications. In no event shall ICT be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential or incidental, including without limitation, any damages for lost profits, stolen goods, or claims by any other party caused by defective goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of the merchandise sold.

Protege® and the Protege® Logo are registered trademarks of Integrated Control Technology Limited.

227-5045-000

prt-ctrl-din protege gx din rail system … cell backup battery n+ n- nbna +-v1+ v1+ v1+ v1+ v1+ v1+...

Documents