pulverizers nual - woods equipment company4 introduction man0130 (8/24/01) specifications...

OP

ER

AT

OR

'S M

AN

UA

L

PULVERIZERSM

AN

0130

Rev

. 8/1

/201

3

Tested. Proven. Unbeatable.

20A14820A160SU172SU184

SU172BTSU184BT

2 Introduction Gen’l (Rev. 12/5/2011)

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructionsand safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualare completed before releasing equipment to the owner.

The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies thatall Dealer Check List items have been completed. Dealers can register all Woods product atdealer.WoodsEquipment.com under Product Registration.

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better andsafer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and becomeacquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can beobtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or inthe United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable andsatisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessarytools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required forsafe and satisfactory operation. Record the model number and serial number of your equipment in the spacesprovided:

Model: _______________________________ Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle withan exclamation mark) to indicate the degree of hazard for items of personal safety.

Introduction 3MAN0130 (8/24/01)

TABLE OF CONTENTSINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSIDE FRONT COVER

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6

SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11

OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

PARTS LISTS

20A148 & 20A160 PULVERIZERS. . . . . . . . . . . . . . . . . . . . . . . . . 14

SU172 & SU184 PULVERIZERS . . . . . . . . . . . . . . . . . . . . . . . . . . 15

SU172BT & SU184BT PULVERIZERS . . . . . . . . . . . . . . . . . . . . . 16

SECOND ROLLER KITS (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . 17

HITCH KIT FOR 20A148 (OPTIONAL). . . . . . . . . . . . . . . . . . . . . . 17

BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . INSIDE BACK COVER

GENERAL INFORMATIONThe purpose of this manual is to assist you in operatingand maintaining your Pulverizer. Read it carefully. It fur-nishes information and instructions that will help youachieve years of dependable performance. Theseinstructions have been compiled from extensive fieldexperience and engineering data. Some informationmay be general in nature due to unknown and varyingoperating conditions. However, through experienceand these instructions, you should be able to developprocedures suitable to your particular situation.

The illustrations and data used in this manual were cur-rent at the time of printing. However, due to possibleinline production changes, your machine may varyslightly in detail. We reserve the right to redesign andchange the machines as may be necessary withoutnotification.

Throughout this manual, references are made to rightand left directions. These are determined by standingbehind the tractor facing the direction of forward travel.

Si no lee Ingles, pida ayuda a alguien que si lo lea para que le

traduzca las medidas de seguridad.

LEA EL INSTRUCTIVO!!

(Rev. 4/29/2005)

4 Introduction MAN0130 (8/24/01)

SPECIFICATIONS

Specification 20A148 20A160

Working width 48" 60"

Overall width 54" 66"

Height to top of A-frame 36" 36"

Depth, front to back 28-1/2" 28-1/2"

Weight 480 lbs 550 lbs

Roller diameter 6-5/8" O.D. 6-5/8" O.D.

Roller pins 3/8" dia. x 1-1/8" long (hardened pins)

3/8" dia. x 1-1/8" long (hardened pins)

Scarifier teeth Hardened 5/8" sq. Hardened 5/8" sq.

Number of teeth 9 Front8 Rear

11 Front10 Rear

Bearings 1" self-aligning 1" self-aligning

Frame 10" wide flange H-beam(49 lbs-ft)

10" wide flange H-beam(49 lbs-ft)

Tractor hitch requirement Category 1 Category 1

Tractor horsepowerrequirement

45 HP maximum 45 HP maximum

Introduction 5MAN0130 (8/24/01)

SPECIFICATIONS

Specification SU172 SU172BT SU184 SU184BT

Working width 72" 72" 84" 84"

Overall width 78" 78" 90" 90"

Height to top of A-frame 36" 36" 36" 36"

Depth, front to back 30-1/2" 30-1/2" 30-1/2" 30-1/2"

Weight 715 lbs 735 lbs 784 lbs 805 lbs

Roller diameter 6-5/8" OD 6-5/8" OD 6-5/8" OD 6-5/8" OD

Roller pins 3/8" dia. x 1-1/8" long (hardened pins)




Scarifier teeth Hardened 5/8" sq. Hardened 1/2" x 2" x 13" reversible

Hardened 5/8" sq. Hardened 1/2" x 2" x 13" reversible

Number of teeth 14 Front13 Rear

14 Front13 Rear

16 Front15 Rear

16 Front15 Rear

Bearings 1" self-aligning 1" self-aligning 1" self-aligning 1" self-aligning

Frame 12" wideflange H-beam (53 lbs-ft)

12" wideflange H-beam (53 lbs-ft)



Tractor hitch requirement Category 1 Category 1 Category 1 Category 1

Tractor horsepowerrequirement

65 HPmaximum

65 HPmaximum

65 HPmaximum

65 HPmaximum

6 Safety Landscape Misc. SR (Rev. 5/16/2003)

TRAINING

Safety instructions are important! Read allattachment and power unit manuals; follow allsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locate your nearest dealer, checkthe Dealer Locator at www.WoodsEquipment.com,or in the United States and Canada call 1-800-319-6637.) Failure to follow instructions or safety rulescan result in serious injury or death.

If you do not understand any part of this manualand need assistance, see your dealer.

Know your controls and how to stop engine andattachment quickly in an emergency.

Operators must be instructed in and be capableof the safe operation of the equipment, its attach-ments, and all controls. Do not allow anyone tooperate this equipment without proper instruc-tions.

Never allow children or untrained persons tooperate equipment.

PREPARATION

Check that all hardware is properly installed.Always tighten to torque chart specificationsunless instructed otherwise in this manual.

Always wear relatively tight and belted clothingto avoid entanglement in moving parts. Wearsturdy, rough-soled work shoes and protectiveequipment for eyes, hair, hands, hearing, and head;and respirator or filter mask where appropriate.

Make sure attachment is properly secured,adjusted, and in good operating condition.

Power unit must be equipped with ROPS orROPS cab and seat belt. Keep seat belt securelyfastened. Falling off power unit can result in deathfrom being run over or crushed. Keep foldableROPS systems in “locked up” position at all times.

Make sure all safety decals are installed.Replace if damaged. (See Safety Decals section forlocation.)

A minimum 20% of tractor and equipmentweight must be on the tractor front wheels whenattachments are in transport position. Without thisweight, front tractor wheels could raise up result-ing in loss of steering. The weight may be attainedwith front wheel weights, ballast in tires or fronttractor weights. Weigh the tractor and equipment.Do not estimate.

OPERATION

Do not operate or transport equipment whileunder the influence of alcohol or drugs.

Always comply with all state and local lightingand marking requirements.

Operate only in daylight or good artificial light.

Keep bystanders away from equipment.

Keep hands, feet, hair, and clothing away fromequipment while engine is running. Stay clear of allmoving parts.


Never allow riders on power unit or attachment.

Always sit in power unit seat when operatingcontrols or starting engine. Securely fasten seatbelt, place transmission in neutral, engage brake,and ensure all other controls are disengagedbefore starting power unit engine.

Look down and to the rear and make sure areais clear before operating in reverse.

Use extreme care when working close to fences,ditches, other obstructions, or on hillsides.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions sud-denly on slopes.

Use extreme care and reduce ground speed onslopes and rough terrain.

Safety is a primary concern in the design andmanufacture of our products. Unfortunately, ourefforts to provide safe equipment can be wipedout by an operator’s single careless act.

In addition to the design and configuration ofequipment, hazard control and accident preven-tion are dependent upon the awareness, con-cern, judgement, and proper training ofpersonnel involved in the operation, transport,maintenance, and storage of equipment.

It has been said, “The best safety device is aninformed, careful operator.” We ask you to bethat kind of operator.

SAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety 7Landscape Misc. SR (Rev. 5/16/2003)

Watch for hidden hazards on the terrain duringoperation.

Stop power unit and equipment immediatelyupon striking an obstruction. Turn off engine,remove key, inspect, and repair any damage beforeresuming operation.

TRANSPORTATION Power unit must be equipped with ROPS orROPS cab and seat belt. Keep seat belt securelyfastened. Falling off power unit can result in deathfrom being run over or crushed. Keep foldableROPS system in “locked up” position at all times.

Always sit in power unit seat when operatingcontrols or starting engine. Securely fasten seatbelt, place transmission in neutral, engage brake,and ensure all other controls are disengagedbefore starting power unit engine.

A minimum 20% of tractor and equipmentweight must be on the tractor front wheels whenattachments are in transport position. Without thisweight, front tractor wheels could raise up result-ing in loss of steering. The weight may be attainedwith front wheel weights, ballast in tires or fronttractor weights. Weigh the tractor and equipment.Do not estimate.

Always comply with all state and local lightingand marking requirements.

Never allow riders on power unit or attachment.

Do not operate or transport on steep slopes.

Do not operate or transport equipment whileunder the influence of alcohol or drugs.

MAINTENANCE Always wear relatively tight and belted clothingto avoid getting caught in moving parts. Wearsturdy, rough-soled work shoes and protectiveequipment for eyes, hair, hands, hearing, and head;and respirator or filter mask where appropriate.

Never go underneath equipment (lowered to theground or raised) unless it is properly blocked andsecured. Never place any part of the body under-neath equipment or between moveable parts evenwhen the engine has been turned off. Hydraulicsystem leak down, hydraulic system failures,mechanical failures, or movement of control leverscan cause equipment to drop or rotate unexpect-edly and cause severe injury or death.

Make sure attachment is properly secured,adjusted, and in good operating condition.

Before dismounting tractor or performing anyservice or maintenance, lower attachment toground, turn off engine, set parking brake, operatevalve levers to release any hydraulic pressure, andremove key.

Do not modify or alter or permit anyone else tomodify or alter the equipment or any of its compo-nents in any way.

Never perform service or maintenance withengine running.

Keep all persons away from operator controlarea while performing adjustments, service, ormaintenance.

Tighten all bolts, nuts, and screws to torquechart specifications. Check that all cotter pins areinstalled securely to ensure equipment is in a safecondition before putting unit into service.

Make sure all safety decals are installed.Replace if damaged. (See Safety Decals section forlocation.)

STORAGE

Block equipment securely for storage.

Keep children and bystanders away from stor-age area.

SAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

8 Safety MAN0130 (8/17/01)

1 – Serial Number Plate

2 – 55121

ALL MODELS

MODEL NO. SERIAL NO.

Woods Equipment CompanyOregon, Illinois, U.S.A.

(CENTER)

5

4CD5935-Var

WARNING

55121--C

FALLING OFF CAN RESULT IN BEING RUN OVER. Tractor must be equipped with ROPS (or ROPS CAB) and

seat belt. Keep foldable ROPS systems in “locked up”position at all times.

Buckle Up! Keep seat belt securely fastened. Allow no riders.

RAISED IMPLEMENT CAN DROP AND CRUSH. Never go underneath raised implement which can drop

from equipment or tractor 3-point hitch hydraulic leakdown, hydraulic system failures, movement of controllevers or mechanical linkage failures.

Service work does not require going underneathimplement. Read manual instructions.

FALLING OFF OR GOING UNDERNEATH IMPLEMENTCAN RESULT IN SERIOUS INJURY OR DEATH.

TO AVOID SERIOUS INJURY OR DEATH:� Read Operator's Manual before operating, servicing or

repairing equipment. Follow all safety rules and instructions. (Manuals are available from dealer or call 1-800-319-6637.)

� Operate from tractor seat only.� Lower equipment to ground, stop engine, remove key

and set brake before dismounting tractor.� Never allow children or untrained persons to operate

equipment.� Never allow riders.� Keep bystanders away from equipment during operation.� Keep all shields in place and in good condition.� Do not transport towed or semi-mounted units over 20

mph.

FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.

55122-D

WARNING

20A14820A160

3 – 55122

2

3

5

1

SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

(Rev. 4/29/2005)

Safety 9MAN0130 (8/17/01)

SAFETY & INSTRUCTIONAL DECALSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

5

4 CD5925-Var

4

5

CD5935-Var

WARNING

1003750

ENTANGLEMENT AND FALLING HAZARD

Do not stand on rollers while machine is in operation or parked.

Failure to follow these instructions could result in serious injury or death.

4 – 1003750SU172SU184

CRUSHING AND PINCHING HAZARD� Be extremely careful handling various parts of

the machine. They are heavy and hands, fingers, feet, and other body parts could be crushed or pinched between tractor and implement.

� Operate tractor controls from tractor seat only. � Do not stand between tractor and implement

when tractor is in gear. � Make sure parking brake is engaged before

going between tractor and implement.� Stand clear of machine while in operation or

when it is being raised or lowered. FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

WARNING

1003751-A

5 – 1003751

SU172BTSU184BT

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

(Rev. 4/29/2005)

10 Operation MAN0130 (Rev. 11/11/2005)

OPERATION

The operator is responsible for the safe operation ofthis pulverizer. The operator must be properly trained.Operators should be familiar with the equipment, thetractor, and all safety practices before starting opera-tion. Read the safety rules and safety decals on pages6 through 9.


Never allow children or untrained persons tooperate equipment.

Keep bystanders away from equipment.

Keep hands, feet, hair, and clothing away fromequipment while engine is running. Stay clear of allmoving parts.

Always wear relatively tight and belted clothingto avoid entanglement in moving parts. Wearsturdy, rough-soled work shoes and protectiveequipment for eyes, hair, hands, hearing, and head.

PRE-OPERATION CHECK LIST(OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safetydecal instructions on pages 6 through 9.

___ Check that equipment is properly and securelyattached to tractor.

___ Check that all safety decals are installed and ingood condition. Replace if damaged.

___ Do not allow riders.

___ Check that all hardware is properly installed andsecured.

___ Check all lubrication points and grease asinstructed in Lubrication Information, page 12.

___ Make sure tractor ROPS or ROPS CAB and seatbelt are in good condition. Keep seat beltsecurely fastened during operation.

GENERAL INFORMATION

The pulverizer is designed to immediately follow roughgrading by a motor grader or bulldozer. The pulverizer

is also an excellent companion tool to a rollover,box-type scraper or utility blade for the purpose of scar-ifying hard clay or loamy soils.

The pulverizer may be used with either constant draftcontrol or implement position control stops. Normally, itis better to use implement position control during theinitial portion of the job, especially when the pulverizeris operated in reverse. When the finished gradebecomes more established, switching to control draftwill speed up the work. Experiment with both settingsto determine the best method for your particular appli-cation.

ATTACHING PULVERIZER TO TRACTOR

1. Place the pulverizer on a level, dry area, positionedbehind the tractor. Connect pulverizer mountingpins to tractor lower arms.

2. Secure mounting pins to lift arms with 7/16 x 1-3/4"lynch pins.

3. Connect the tractor top link to the pulverizer uppermast.

NOTE: Initial adjustment of the top link must bemade on a level surface.

4. Rest scarifier teeth on the ground and level the pul-verizer by extending or retracting the top link.

5. Carefully operate the pulverizer through the trac-tor’s full lift range, making sure pulverizer does notcome into contact with any tractor component.

6. Adjust top link if necessary.

ADJUSTING TOP LINK

Top link adjustment is critical to the pulverizer’s perfor-mance. The unit can be pitched either forward or rear-ward, depending on the soil conditions and jobrequirements.

You will need to experiment to determine the best set-ting for the job being performed.

For normal conditions, the pulverizer should beadjusted in a level position. This is especially usefulwhen finish leveling and back filling.

When excessive debris or hard scarifying conditionsexist, pitch the pulverizer forward to optimize perfor-mance.

Pitching the pulverizer rearward will optimize rolleraction and assist in over-seeding applications.

��

CAUTION

Operation 11MAN0130 (Rev. 11/11/2005)

ADJUSTING ROLLER SPRINGThe roller springs are assembled loose at the factoryfor normal operating conditions. For abnormal operat-ing conditions, you may want to make the adjustmentsin the chart below. Compressing springs 1 inch will put100 pounds of pressure on the primary roller. Adjustingsecondary roller springs 1/2 inch will put an additional100 pounds of pressure on that roller.

SCARIFIER TEETH SETTING

The 8" scarifying teeth are set at the factory at 3-1/2"below the H-beam flange.

Do not lower the spikes, this will result in additionalstrain and cause excess scarifying before leveling andgrading.

OPERATING TIPS

CONDITION ADJUSTMENT

Hard, tight clay Additional spring tension

Loamy, loose soil No adjustment

Loose, sandy soil Run with no tension on roller

DIRECTION ACTION APPLICATION

Forward Straight line General purpose pulverizing

Long arcs For seeding, dressing out soil during final seedbed preparation, and stockpiling debris into a single pile

Short, tight arcs For hard, tight clay conditions; centrifugal force applied to roller pins will allow faster pulverizing

Reverse Clod breaking & pulverizing Improves clod breaking, especially with SU models

Leveling Scarifier teeth promote even, ideal seedbed

Backfilling Light backfilling around foundations and sidewalks

PROCEDURE ACTION ADVANTAGE

Grading Grade at 90° angles Helps eliminate swells and valleys. Establishes grade lines more quickly

Humps Pull humps into low places close to the area being pulverized

Saves time

(Rev. 8/1/2013)

12 Owner Service MAN0130 (Rev. 11/11/2005)

OWNER SERVICE

The information in this section is written for operatorswho possess basic mechanical skills. If you need help,your dealer has trained service technicians available.For your protection, read and follow the safety informa-tion in this manual.

NEVER GO UNDERNEATH EQUIPMENT. Neverplace any part of the body underneath equipmentor between moveable parts even when the enginehas been turned off. Hydraulic system leak down,hydraulic system failures, mechanical failures, ormovement of control levers can cause equipmentto drop or rotate unexpectedly and cause severeinjury or death.

• Service work does not require going under-neath.• Read Operator's Manual for service instruc-tions or have service performed by a qualifieddealer.

Keep all persons away from operator controlarea while performing adjustments, service, ormaintenance.

Before dismounting power unit or performingany service or maintenance, follow these steps:disengage power to equipment, lower the 3-pointhitch and all raised components to the ground,operate valve levers to release any hydraulic pres-sure, set parking brake, stop engine, remove key,and unfasten seat belt.

Always wear relatively tight and belted clothingto avoid entanglement in moving parts. Wearsturdy, rough-soled work shoes and protectiveequipment for eyes, hair, hands, hearing, and head.

LUBRICATION INFORMATIONThe roller bearings are self-aligning, dust-proof ballbearings. Use any good grade of multi-purpose greaseand lubricate as needed.

Figure 1 shows lubrication locations and frequency.Harsh conditions may require more frequent lubrica-tion.

Figure 1. Lubrication Points

��

��

CAUTION

CD5925-Var

8(BOTH SIDES)

Owner Service 13MAN0130 (Rev. 11/11/2005)

CLEANING

After Each Use● Remove large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

● Inspect machine and replace worn or damagedparts.

● Replace any safety decals that are missing or notreadable.

Periodically or Before Extended Storage● Clean large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

● Remove the remainder using a low-pressure waterspray.

1. Be careful when spraying near scratched ortorn safety decals or near edges of decals aswater spray can peel decal off surface.

2. Be careful when spraying near chipped orscratched paint as water spray can lift paint.

3. If a pressure washer is used, follow the adviceof the pressure washer manufacturer.

● Inspect machine and replace worn or damagedparts.

● Sand down scratches and the edges of areas ofmissing paint and coat with spray paint of matchingcolor (purchase from your dealer).

● Replace any safety decals that are missing or notreadable (supplied free by your dealer). See SafetyDecals section for location drawing.

NOTES

14 Assembly WPMAN0130 (8/24/01)

ASSEMBLY

SECOND ROLLER KIT (OPTIONAL)

1. From right and left roller hinges, remove 5/8" capscrew (15), lock washer (17), and hex nut (16).

2. Roll the roller kit forward until right and left rollerarms (4, 5 - not shown) from base unit are insertedinto right and left roller hinges (2, 3 - not shown).

3. Align holes and reinstall cap screw, lock washer,and hex nut in each side.

Figure 2. Roller Kit Installation(Right side shown)

HITCH KIT (OPTIONAL)

NOTE: Only fits 20A148 pulverizers made afterserial number 967826. This hitch kit allows higher 3-point hitch lift height on sub-compact tractors.

Figure 3. Hitch Kit Installation - 20A148 Only

1. Remove sleeve, nut, washers and bolt from thelower hole in the upper third point area. Re-installin the upper hole, Figure 4. Torque to 297 lbs-ft(403 N-m).

Figure 4. Upper Hitch Hardware Installation

2. Remove hitch pins from the pulverizer.

3. Place the slot of the hitch plate over the I-beamwith the bend toward the inside.

4. Secure into position using cap screw (4), lockwasher (5), and hex nut (6). The head of the capscrew must be on the inside of the A-frame.

5. Insert hitch pin into lower holes.

6. Torque hardware to 474 lbs-ft (642 N-m).

7. Repeat for opposite side.

Figure 5. Hitch Plate Installation(Right side shown)

4 2

15 1716

2. Roller hinge, right4. Roller kit arm, right

15. 5/8 NC x 2-1/4 Cap screw16. 5/8 NC Hex nut17. 5/8 Heavy lock washer

1

2

34, 5, 6

CD6550-var

3

4, 5, 6

1. Top link sleeve & hardware

2. Hitch plate, right3. Hitch plate, left4. 7/8 NC x 2-1/2 Cap screw GR55. 7/8 Lock washer6. 7/8 NC Hex nut

SLOT

2

(Rev. 4/29/2005)

Dealer Check Lists 15MAN0130 (8/24/01)

DEALER CHECK LISTS

The Pulverizer is completely assembled at the factoryfor your convenience. Before delivering it to the cus-tomer, complete the following check lists.

PRE-DELIVERY CHECK LIST(DEALER’S RESPONSIBILITY)

Inspect the equipment thoroughly before delivering it tothe customer:

___ Check that all safety decals are installed and ingood condition. Replace if damaged.

___ Check all bolts to be sure they are properlytorqued.

___ Check that all cotter pins and safety pins areproperly installed. Replace if damaged.

DELIVERY CHECK LIST(DEALER’S RESPONSIBILITY)

___ Present Operator's Manual and request that cus-tomer and all operators read it before operatingequipment. Point out the manual safety rules,

explain their meanings and emphasize theincreased safety hazards that exist when safetyrules are not followed.

___ Show customer how to make adjustments.

___ Instruct customer how to lubricate and explainimportance of lubrication.

___ Show customer the safe, proper procedures to beused when mounting, dismounting, and storingequipment.

___ Explain to customer the potential crushing haz-ards of going underneath raised equipment.Instruct customer that service work does notrequire going underneath unit and never to do so.

___ Add wheel weights, ballast in front tires, and/orfront tractor weight to enhance front end stability.A minimum 20% of tractor and equipment grossweight must be on the front tractor wheels. Whenadding weight to attain 20% of tractor and equip-ment weight on front tractor wheels, you must notexceed the ROPS weight certification. Weigh thetractor and equipment. Do not estimate!

(Rev. 4/29/2005)

16 Parts MAN0130 (8/17/01)

20A148 & 20A160 PULVERIZERS

1

3

4

5

6

7

8

9

10

11

12

1313

1415

16

17

19

20

212223

CD5931A

26

REF PART QTY DESCRIPTION

1 ** 1 20A160 H-BEAM -or-

1 ** 1 20A148 H-BEAM

3 1003162 1 ROLLER 60" -or-

3 1003161 1 ROLLER 48"

4 1003165 2 ROLLER ARM RETAINER

5 1003720 1 ROLLER ARM RIGHT

6 1003721 1 ROLLER ARM LEFT

7 565 * 2 WASHER, 3/8 FLAT

8 29485 4 NUT, JAM 3/4 NC

9 20A111 2 SPRING STUD (LONG)

10 20A125 2 SPRING (LONG)

11 20A920 2 1" BEARING W/HOUSING

12 32933 2 PIN, CLEVIS 3/8 X 2-1/4

13 4674 * 6 3/8 X 2 SPIROL PIN

14 835 * 8 NUT, HEX 3/8 NC PLTD

15 838 * 8 WASHER, 3/8 LOCK

16 976 * 8 HHCS, 3/8 NC X 1-1/2 GR5

17 SU105 2 CAT 1 DRAWBAR PIN WITH LYNCH PIN

19 1256 * 2 3/16 X 1 COTTER PIN

20 20A122 AR 8" SPIKE

21 20A108 AR U-BOLT, ZINC


22 5664 * AR WASHER, 7/16 STD D LOCK

23 29685 AR NUT, HEX 7/16 NF

24 1003787 1 DECAL SET, SAFETY

25 1003788 1 DECAL SET COMPLETE

26a 1002018 1 SLEEVE - .81 X 1.25 X 2.12

26b 31207 * 1 HHCS, 3/4 NC X 4 GR5

26c 1257 * 2 WASHER, 3/4 FLAT

26d 2371 * 1 NUT, LOCK 3/4 NC

NS 1005337 1 50 PIN REPLACEMENT SET

* Standard hardware; obtain locally

** Not serviced separately

NS Not shown

AR As required

24 – SAFETY DECAL SET

25 – COMPLETE DECAL SET

(Rev. 11/11/2005)

Parts 17MAN0130 (8/17/01)

SU172 & SU184 PULVERIZERS

1

3

68

9

10

1313

17

20

212223

4

57

11

12

1415

16

19CD5933A

26


1 ** 1 84" BEAM SU -or-

1 ** 1 72" BEAM SU

3 1003164 1 ROLLER 84" -or-

3 1003163 1 ROLLER 72"


5 1003720 1 ROLLER ARM RT

6 1003721 1 ROLLER ARM LT

7 565 * 2 WASHER, 3/8 FLAT

8 29485 4 NUT, JAM 3/4 NC




12 32933 2 PIN, CLEVIS 3/8 X 2-1/4

13 4674 * 6 3/8 X 2 SPIROL PIN

14 835 * 8 NUT, HEX 3/8 NC PLTD

15 838 * 8 WASHER, 3/8 LOCK

16 976 * 8 HHCS, 3/8 NC X 1-1/2 GR5


19 1256 * 2 3/16 x 1 COTTER PIN

20 20A122 AR 8" SPIKE




23 29685 AR NUT, HEX 7/16 NF



26a 1002018 1 SLEEVE - .81 X 1.25 X 2.12

26b 31207 * 1 HHCS, 3/4 NC X 4 GR5

26c 1257 * 2 WASHER, 3/4 FLAT

26d 2371 * 1 NUT, LOCK 3/4 NC




NS Not shown

AR As required

24 – SAFETY DECAL SET

25 – COMPLETE DECAL SET

(Rev. 11/11/2005)

18 Parts MAN0130 (8/17/01)

SU172BT & SU184BT PULVERIZERS

1

3

4

5

6

7

8

9

10

11

121313

1415

16

17

19

20

212223

CD5932A

26


1 ** 1 84" BEAM SU BT -or-

1 ** 1 72" BEAM SU BT

3 1003164 1 ROLLER 84" -or-

3 1003163 1 ROLLER 72"


5 1003720 1 ROLLER ARM RIGHT

6 1003721 1 ROLLER ARM LEFT

7 565 * 2 WASHER, 3/8 FLAT

8 29485 4 NUT, JAM 3/4 NC




12 32933 2 PIN, CLEVIS 3/8 X 2-1/4

13 4674 * 6 3/8 X 2 SPIROL PIN

14 835 * 8 NUT, HEX 3/8 NC PLTD

15 838 * 8 WASHER, 3/8 LOCK

16 976 * 8 HHCS, 3/8 NC X 1-1/2 GR5


19 1256 * 2 3/16 X 1 COTTER PIN

20 1003722 AR BIG TOOTH




23 29685 AR NUT, HEX 7/16 NF



26a 1002018 1 SLEEVE - .81 X 1.25 X 2.12

26b 31207 * 1 HHCS, 3/4 NC X 4 GR5

26c 1257 * 2 WASHER, 3/4 FLAT

26d 2371 * 1 NUT, LOCK 3/4 NC




NS Not shown

AR As required

24 – SAFETY DECAL SET25 – COMPLETE DECAL SET

(Rev. 11/11/2005)

Parts 19MAN0130 (8/17/01)

1003710, 1003711, 1003712 & 1003713 SECOND ROLLER KITS (OPTIONAL)

1

3

5

22

CD5934

2

4

6

7

8

9

1011

12

13

14

15

1617

1819

20

21

CD6550A

1

2

3

4, 5, & 6


1 1003161 1 ROLLER 48" -or-

1003162 1 ROLLER 60" -or-

1003163 1 ROLLER 72" -or-

1003164 1 ROLLER 84"

2 1003700 1 ROLLER HINGE RIGHT

3 1003701 1 ROLLER HINGE LEFT

4 1003718 1 ROLLER KIT ARM RIGHT

5 1003719 1 ROLLER KIT ARM LEFT

6 29485 4 NUT, JAM 3/4 NC

7 20A920 2 BEARING - 1.0

8 3231 * 2 HHCS, 3/8 NC X 2 GR5

9 410 2 PIN, CLEVIS 5/8 X 1-3/4

10 835 * 8 NUT, HEX 3/8 NC PLTD

11 838 * 8 WASHER, 3/8 LOCK

12 976 * 8 HHCS, 3/8 NC X 1-1/2 GR5

13 SU228 2 SPRING STUD REAR


14 SU229 2 SPRING REAR (SHORT)

15 12274 * 4 HHCS, 5/8 NC X 2-1/4

16 230 * 4 NUT, HEX 5/8 NC PLATED

17 1286 * 4 WASHER, 5/8 HEAVY LOCK

18 565 * 4 WASHER, 3/8 FLAT

19 6698 * 2 NUT, LOCK 3/8 NC

20 3632 * 2 WASHER, 5/8 STD SAE FLAT

21 1256 * 2 3/16 X 1 COTTER PIN

22 4674 * 2 3/8 X 2 SPIROL PIN




NS Not shown

HITCH KIT (OPTIONAL)


A 1010775 1 HITCH KIT, COMPLETE

1 † 1 TOP LINK SLEEVE & HARDWARE2 ** 1 HITCH PLATE, BOLT-ON RH3 ** 1 HITCH PLATE, BOLT-ON LH

4 * 2 HHCS, 7/8 NC X 2-1/2 GR55 * 2 WASHER, 7/8 LOCK6 * 2 NUT, 7/8 NC HEX


** Not sold separately† Pulverizer parts - not included in hitch kit

Only for 20A148 Model after SN 967826

Allows higher 3-point hitch lift height on

sub-compacttractors.

(Rev. 4/29/2005)

Bolt Torque & Size Charts (Rev. 3/28/2007)20 Appendix

BOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual parts list.Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.

Diameter (Inches)

WrenchSize

MARKING ON HEAD

SAE 2 SAE 5 SAE 8

lbs-ft N-m lbs-ft N-m lbs-ft N-m

1/4" 7/16" 6 8 10 13 14 18

5/16" 1/2" 12 17 19 26 27 37

3/8" 9/16" 23 31 35 47 49 67

7/16" 5/8" 36 48 55 75 78 106

1/2" 3/4" 55 75 85 115 120 163

9/16" 13/16" 78 106 121 164 171 232

5/8" 15/16" 110 149 170 230 240 325

3/4" 1-1/8" 192 261 297 403 420 569

7/8" 1-5/16" 306 416 474 642 669 907

1" 1-1/2" 467 634 722 979 1020 1383

Diameter & Thread Pitch (Millimeters)

Wrench Size

Coarse Thread Fine Thread

Diameter & Thread Pitch (Millimeters)

Marking on Head Marking on Head

Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9

N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft

6 x 1.0 10 mm 8 6 11 8 8 6 11 8 6 x 1.0

8 x 1.25 13 mm 20 15 27 20 21 16 29 22 8 x 1.0

10 x 1.5 16 mm 39 29 54 40 41 30 57 42 10 x 1.25

12 x 1.75 18 mm 68 50 94 70 75 55 103 76 12 x 1.25

14 x 2.0 21 mm 109 80 151 111 118 87 163 120 14 x 1.5

16 x 2.0 24 mm 169 125 234 173 181 133 250 184 16 x 1.5

18 x 2.5 27 mm 234 172 323 239 263 194 363 268 18 x 1.5

20 x 2.5 30 mm 330 244 457 337 367 270 507 374 20 x 1.5

22 x 2.5 34 mm 451 332 623 460 495 365 684 505 22 x 1.5

24 x 3.0 36 mm 571 421 790 583 623 459 861 635 24 x 2.0

30 x 3.0 46 mm 1175 867 1626 1199 1258 928 1740 1283 30 x 2.0

A

SAE SERIES TORQUE CHART

SAE Bolt Head Identification

SAE Grade 2(No Dashes)

SAE Grade 5(3 Radial Dashes)

SAE Grade 8(6 Radial Dashes)

A

METRIC SERIES TORQUE CHART

Metric Bolt Head Identification

8.8

MetricGrade 10.9

10.9

MetricGrade 8.8

A

A A

Typical Washer Installations Lock Washer

Flat Washer

8/9/00

Bolt

Appendix 21Bolt Torque & Size Charts (Rev. 3/28/2007)

BOLT SIZE CHARTNOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

ABBREVIATIONSAG .............................................................. AgricultureASABE.................... American Society of Agricultural &

Biological Engineers (formerly ASAE)ASAE ....... American Society of Agricultural EngineersATF ............................... Automatic Transmission FluidBSPP .............................British Standard Pipe ParallelBSPTM ................British Standard Pipe Tapered MaleCV.....................................................Constant VelocityCCW .............................................. Counter-ClockwiseCW............................................................... ClockwiseF ...................................................................... FemaleFT .............................................................. Full ThreadGA .................................................................... GaugeGR (5, etc.) ........................................... Grade (5, etc.)HHCS ........................................Hex Head Cap ScrewHT........................................................... Heat-TreatedJIC .................Joint Industry Council 37° Degree FlareLH .................................................................Left HandLT........................................................................... Leftm......................................................................... Metermm................................................................MillimeterM.......................................................................... Male

MPa.........................................................Mega Pascal

N.......................................................................Newton

NC ......................................................National Coarse

NF ...........................................................National Fine

NPSM.....................National Pipe Straight Mechanical

NPT .......................................... National Pipe Tapered

NPT SWF .........National Pipe Tapered Swivel Female

ORBM .......................................... O-Ring Boss - Male

P...........................................................................Pitch

PBY ...................................................... Power-Beyond

psi..........................................Pounds per Square Inch

PTO..................................................... Power Take Off

QD....................................................Quick Disconnect

RH ..............................................................Right Hand

ROPS ........................... Roll-Over Protective Structure

RPM ........................................Revolutions Per Minute

RT ....................................................................... Right

SAE ..........................Society of Automotive Engineers

UNC .....................................................Unified Coarse

UNF...........................................................Unified Fine

UNS......................................................Unified Special

5/16 3/8 1/2 5/8 3/4 7/8SAE Bolt Thread Sizes

MM 25 50 75 100 125 150 175

IN 1 7

Metric Bolt Thread Sizes8MM 18MM14MM12MM10MM 16MM

2 3 4 5 6

F-3079 (Rev. 3/2/2012)

Woods Equipment Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA

800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com

WARRANTYAll Models Except Mow’n MachineTM Zero-Turn Mowers

Please Enter Information Below and Save for Future Reference.

Date Purchased: ____________________________ From (Dealer): __________________________________________

Model Number: ____________________________ Serial Number: __________________________________________

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forthbelow, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THEPRODUCT TO THE ORIGINAL PURCHASER.

All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.

The warranty periods for specific parts or conditions are listed below:

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected toimproper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materiallymodified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts otherthan those obtainable through WOODS.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to athird party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.

WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured byWOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, inits sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof ofpurchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through thedealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair orreplacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODSMAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTYOF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from theproduct, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legaltheory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenuesor goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery orrental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacturereplacement parts.

No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, itsauthorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty. Answers to any questions regardingwarranty service and locations may be obtained by contacting:

Part or Condition Warranted

Model NumberDuration (from date of delivery to the original

purchaser)

All units invoiced after 4/30/2012

Gearbox components

BW1260, BW1620, BW1800, BW1260X, BW1800X, BW2400

6 years

BW240HD, BW180HD, BW180HB, BW126HB, BW126XHD, BW180XHD

BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240, BW126X, BW180X

PHD25, PHD35, PHD65, PHD95, DS96, DS120, RCC42, RD990X, PRD6000, PRD7200, PRD8400,S15CD, S20CD, S22CD, S25CD, S27CD, S30CD BW15LH, TC/R74, TC/R68, TC/R60, TBW144,TBW180, TBW204

RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44, HC48, HC54, HC60, HC72 3 years (1 year if used in rental or commercial applications)

Blade spindles RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204 3 years

Rust-through BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB,BW180HD, BW1260, BW1800, BW240, BW240HD, DS1260, DSO1260, DS1440, TS1680 10 years

F-8494 (Rev. 2/5/2013)

Woods EquipmentA Blount International Company2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061

800-319-6637 tel800-399-6637 faxwoodsequipment.com

©2013 Woods Equipment Company. All rights reserved. Woods® and the Woods logo are trademarks of Woods Equipment Company. All othertrademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respectivecompanies or mark holders. Specifications subject to change without notice.

WARRANTY(Replacement Parts For All Models Except Mow’n MachineTM

Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaserwith the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion ofWOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warrantydoes not cover normal wear or tear, or normal maintenance items.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell orotherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in anyway. There are no third party beneficiaries of this Warranty.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free ofcharge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with thisWarranty. The product must be returned to WOODS with proof of purchase within thirty (30) days aftersuch defect or noncompliance is discovered or should have been discovered, routed through the dealer anddistributor from whom the purchase was made, transportation charges prepaid. WOODS shall completesuch repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NOOTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THESOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THISWARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODSSPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANYIMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directlyor indirectly from the product, whether such claim is based upon breach of contract, breach of warranty,negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing,Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss ofcrops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitutemachinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtainmaterials or manufacture replacement parts.

No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, includingwithout limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify,or enlarge this Warranty.

Answers to any questions regarding warranty service and locations may be obtained by contacting:

PART NO.

MAN0130

© 2001 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, Gill, and "Tested. Proven. Unbeatable." are trademarks ofWoods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in thismanual are the property of their respective companies or mark holders. Specifications subject to change without notice.

Woods Equipment Company

2606 South Illinois Route 2Post Office Box 1000Oregon, Illinois 61061

815-732-2141 tel815-732-7580 faxwww.WoodsEquipment.com

pulverizers nual - woods equipment company4 introduction man0130 (8/24/01) specifications...

Documents