pvc-u jointing procedures pvc-u jointing procedures · size pipe od mm inch grey pvc-u pressure...
TRANSCRIPT
Page 1
TECH DATA SHEET 1025407/04/15
P V C - U J O I N T I N G P R O C E D U R E S
PVC-U cement is gap fillingPVC-U cement softens the inside of the fitting and the outside of the pipe to form a joint chemically.Strength of joint is reduced if surfaces are not cleaned and properly prepared.
1. Cut the pipe end square.2. Remove burrs and clean out swarf. A chamfer must be filed approx 3mm x 45º (This will prevent the layer of cement
being scraped away as the pipe is pushed into the fitting).3. Use a felt marker pen or pencil to mark the pipe at the distance which will penetrate the socket to the root/stop.4. Thoroughly clean the surfaces of both pipe and fittings with MEK cleaner on a clean lint-free cloth. Please note it is
not necessary to abrade pipe or fitting unless pipes are discoloured/sun bleached.5. Stir the PVC-U Cement thoroughly.6. Use a clean brush approximately half as wide as the pipe to be jointed.
Apply cement to the pipe and fittings using longitudinal strokes.The pipe should have a slightly thicker coating than the fitting.The prepared areas should be completely covered with cement.Note: It is important to apply cement quickly to enable assembly without excessive force being required.
7. Immediately after application of cement push pipe fully home into the fitting without rotating.Hold the pipe and fitting for up to a minute, depending on size, to ensure fitting does not slide off the pipe.Note: When working under cold conditions ensure the joints are free from frost and moisture and allow extracuring time.
8. Wipe off excess cement from both sides of the joint using a clean lint-free cloth.9. Replace lids on tins.
10. Clean brush in MEK cleaner.
PRECAUTIONSThe jointing area must be well ventilatedDo not allow a naked flame or smoking in the jointing areaEnsure cement is used prior to its expiry date (shown on bottom of tin)Wear rubber or latex gloves when applying MEK cleaner and PVC-U cementNever dilute PVC-U solvent cementAlways replace lids on tins when not in useAlways use clean brushesAlways use clean lint-free cloth or absorbent paperUse a shelter to keep jointing surfaces dry in wet weather
CEMENT SETTING TIMES
NOMINAL BORE3/8" - 1/2"3/4" - 1"
11/4" - 2"21/2"
3"4"
5" - 6"8"10"12"
NUMBER OF JOINTS1300650160907030201284
TYPE AND SIZE OF BRUSH4mm Round8mm Round
1" Flat2" Flat2" Flat3" Flat3" Flat3" Flat3" Flat3" Flat
NUMBER OF PEOPLE1111223333
CEMENT USAGE RECOMMENDATIONSThe following is an estimation of the number of joints likely to be achieved per litre of solvent cement.
PIPE DIAMETERTemperature
>10ºC5ºC to 10ºC
Up to 10 bar2 h4 h
Up to 16 bar4 h8 h
Up to 10 bar4 h8 h
Up to 16 bar8 h16 h
Up to 10 bar8 h16 h
Up to 16 bar16 h32 h
UP TO 2” 21/2” TO 4” 5” AND ABOVE
These times are applicable to UNI100 Griffon cement.
PIPE DIAMETERTemperature
>15ºC5ºC to 15ºC
10 bar30 min
1 h
5 bar30 min
1 h
10 bar1 h2 h
5 bar2 h4 h
10 bar8 h16 h
UP TO 11/2” 2” TO 4” 5” AND ABOVE
These times are applicable to WDF-05 Griffon cement.
5 bar15 min30 min
16 bar2 h4 h
16 bar4 h8 h
16 bar16 h32 h
PVC-U Jointing Procedures
Page 2
P V C - U J O I N T I N G P R O C E D U R E S
INSTALLING THREADED FITTINGS
1. Ensure all threads are clean.2. Apply PTFE tape to the male thread for 11⁄2 turns in a clockwise direction.3. Screw the female threaded fitting by hand onto the male thread.4. It should be possible to screw the fitting on by hand for 2⁄3 of the thread length.5. After tightening by hand add an extra 1⁄2 turn with a suitable tool ie strap wrench
PRECAUTIONSUse PTFE tape only. Do not use thread seal paste or any other jointing compound. Do not force tightening of the jointunder any circumstances. For connecting plastic pipework systems to metal pipework systems composite unions and/orflanges must be used.
NOTE 2 NOTE 3 NOTE 4
NOTE 6
NOTE 8
NOTE 6
NOTE 8
NOTE 4
NOTE 7
Page 3
20ºC
P V C - U P R E S S U R E P I P E S
NOMINALBORE SPACING GIVEN IN METRES VERTICAL PIPES
Imperial PVC-U products are generally manufactured in accordance with the following standards:
Pipe - EN1452-2
Fittings - EN1452-3 / BS4346 Part 1
Threaded Fittings - BS21, DIN2999, ISO7
Unless otherwise stated PVC-U Pressure Fittings have the following pressure ratings:
Solvent Weld - 3/8” to 8” = Class E/15 bar
Threaded = Class D/12 bar
* All quoted at 20ºC
Pressure ratings for plastic pipework systems are always quoted at 20ºC, it is a fundamental principle of such systems that if the
temperature is increased then the pressure rating must be reduced.
PVC-U systems should never be used for temperatures in excess of 60ºC.
The following chart gives a rough guide as to the pressure/temperature relationship of PVC-U pipework systems.
PVC-U PIPEWORK SUPPORT CENTRES
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”5”6”8”
MANUFACTURING STANDARDS
PVC-U SYSTEM PRESSURE/TEMPERATURE RELATIONSHIP
Temperature (C)
20 30 40 50 60
16.0
14.0
12.0
10.0
8.0
6.0
4.0
2.0
0
Wo
rkin
gPr
essu
re(b
ar)
Class E
Class D
Class C
In above ground installations it is essential to provide support toensure that the weight of the pipe and its contents are adequatelysupported. The recommended maximum support spacings forhorizontal runs of PVC-U pipe are given in the table below.Spacings are calculated assuming the pipes are carrying water.
25ºC 30ºC 35ºC 40ºC 45ºC 20ºC-45ºC
0.750.850.901.001.101.251.401.501.651.852.152.252.50
0.670.770.820.921.051.201.351.451.601.802.102.202.45
0.600.700.750.851.001.151.301.401.551.752.052.152.40
0.500.600.650.750.901.051.201.301.451.651.952.072.32
0.400.500.550.650.800.951.101.201.351.551.852.002.25
0.500.570.700.820.971.071.201.371.721.852.12
0.800.901.001.201.401.601.802.002.202.402.502.502.50
Page 4
SIZE PIPE OD mm
INCH GREY PVC-U PRESSURE PIPE TO EN1452-2
PIPE IS SUPPLIED PLAIN ENDED.PRICE ON APPLICATION FOR OTHER END CONFIGURATIONS IE SPIGOT AND SOCKET/RUBBER RING.PIPES WITH SPIGOT/SOCKET AND RUBBER RING ENDS MAY BE SUBJECT TO MINIMUMMANUFACTURING QUANTITIES AND/OR LEAD TIMES.STANDARD PIPE LENGTH SUPPLIED IS 6 METRES OR 5.8 METRES.ALL WALL THICKNESSES AND PIPE ID’S ARE APPROXIMATE VALUES.
CLASS WALL mm PIPE ID mm Wt (Kg/m)
3/8"
1/2"
3/4"
1
1.1/4”
1.1/2”
"
2"
21/2"
3"
4"
5"
6"
8"
E
E
E
E
E
E
C
E
CE
CE
CE
CE
CE
C
17.1
21.4
26.7
33.6
42.2
48.3
60.3
60.3
75.275.2
88.988.9
114.3114.3
140.2140.2
168.3168.3
219.1
1.5
1.7
1.9
2.2
2.7
3.1
2.5
3.9
3.65.6
3.55.7
4.57.3
6.08.3
6.610.8
7.8
14.1
18.0
22.9
29.2
36.8
42.1
55.3
52.5
68.864.0
81.977.5
105.399.7
128.2123.6
155.1146.7
203.5
0.09
0.17
0.24
0.35
0.55
0.71
0.75
1.10
1.241.86
1.512.37
2.473.86
3.716.60
5.308.37
8.20
P VC-U PRESSURE P IPES
INCH GREY PVC-U PRESSURE PIPE TO EN1452-2
UPVC/ETUBE-3-12 UPVC/ETUBE-3-34 UPVC/ETUBE-3-1 UPVC/ETUBE-3-114 UPVC/ETUBE-3-112
UPVC/CTUBE-3-2UPVC/ETUBE-3-2
UPVC/CTUBE-3-212UPVC/ETUBE-3-212
UPVC/CTUBE-3-3 UPVC/ETUBE-3-3
UPVC/CTUBE-3-4UPVC/ETUBE-3-4
UPVC/CTUBE-3-5UPVC/ETUBE-3-5
UPVC/CTUBE-3-6UPVC/ETUBE-3-6
Page 5
SOCKETS SO13
d L Z E Wt (g)
P V C - U P R E S S U R E F I TT I N G SP L A I N
90º ELBOWS EL53
d L Z E
90º SHORT RADIUS BEND BE33
d
1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
L
161922263138445161
Z E Wt (g)
40506480100126150180220
28354251637794113132
3859118180320535101515902640
Wt (g)
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”5”6”8”10”
141619222631384451617686119147
33333334569111110
23.528344251617588106129161191258320
913203356891682223726201100168542009020
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”5”6”8”
141619222631384451617686119
91114172328344048587381115
23.526.532.54150607589106129164188258
13152442721502853756551080199039908600
SO13-12-UPVC SO13-34-UPVC SO13-1-UPVC SO13-114-UPVC SO13-112-UPVC SO13-2-UPVC SO13-212-UPVC SO13-3-UPVC SO13-4-UPVC SO13-5-UPVC SO13-6-UPVC SO13-8-UPVC
EL53-12-UPVC EL53-34-UPVC EL53-1-UPVC EL53-114-UPVC EL53-112-UPVC EL53-2-UPVC EL53-212-UPVC EL53-3-UPVC EL53-4-UPVC EL53-5-UPVC EL53-6-UPVC EL53-8-UPVC
BE33-12-UPVC BE33-34-UPVC BE33-1-UPVC BE33-114-UPVC BE33-112-UPVC BE33-2-UPVC BE33-212-UPVC BE33-3-UPVC BE33-4-UPVC
Page 6
P V C - U P R E S S U R E F I T T I N G SP L A I N
INCH/METRIC ADAPTOR SOCKET SO14
d x d1
1/2” x 203/4” x 251” x 32
11/4” x 4011/2” x 50
2” x 633” x 904” x 1106” x 160
L1
161922263138516186
L2 Z E E1 Wt (g)
161922263138516190
333333568
28334150
60.575106129181
28334150
60.575106129189
15233660851453536051500
45º ELBOW EY53
d L Z E Wt (g)
EQUAL TEE TE43
d L Z E Wt (g)
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”5”6”8”10”
141619222631384451617686119147
5.55.56810121518212532364962
2328344251617588106130164197258320
101525415912521531050092016402150680012000
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”5”6”8”10”
141619222631384451617686119
147.5
91114172126333947577281114142
2327.533.54251617589106129
162.5188258319
202135631012073654958371440261049501110020020
SO14-3534-UPVC SO14-321-UPVC SO14-40114-UPVC SO14-50112-UPVC SO14-632-UPVC SO14-903-UPVC SO14-1104-UPVC
TE43-12-UPVC TE43-34-UPVC TE43-1-UPVC TE43-114-UPVC TE43-112-UPVC TE43-2-UPVC TE43-212-UPVC TE43-3-UPVC TE43-4-UPVC TE43-5-UPVC TE43-6-UPVC TE43-8-UPVC
EY53-38-UPVCEY53-12-UPVCEY53-34-UPVCEY53-1-UPVCEY53-114-UPVCEY53-112-UPVCEY53-2-UPVCEY53-212-UPVCEY53-3-UPVCEY53-4-UPVCEY53-5-UPVCEY53-6-UPVCEY53-8-UPVCEY53-10-UPVC
Page 7
P V C - U P R E S S U R E F I T T I N G SP L A I N
HOSE ADAPTOR - MALE SPIGOT x MM HOSE TAIL HN63
d x d1 d d1 L H C Wt (g)
1/2”3/4”1”
11/4”11/2”
2”
202532405060
161922263138
70798396108130
242736465565
23305073137208
1/2” x 203/4” x 251” x 32
11/4” x 4011/2” x 50
2” x 60
REDUCING SOCKET RS13
d x d1 L L1 Z E E1 Wt (g)
3/4” x 1/2"1” x 3/4"
11/4” x 1"11/2” x 11/4"
2” x 11/2"21/2” x 2"3” x 21/2"
4” x 3"6” x 4"•
1922263138445161
1619222631384451
66666666
344251617589106129
28334150
60.57588106
325389134225359571940
CROSS CR33
d
* PN10 RATED
L Z E Wt (g)
1/2”3/4”1”
11/4”11/2”
2”21/2”•*
3”•*4”•*
161922263138445163
111417212633404860
27.533.54251617589
264172114233411776
• NON COMER PRODUCT
RANGE OF PP HOSE FITTINGS AVAILABLE SEE PAGE 308
HN63-12-UPVC HN63-34-UPVC HN63-1-UPVC HN63-114-UPVC HN63-112-UPVC HN63-2-UPVC
RS13-3412-UPVC RS13-134-UPVC RS13-1141-UPVC RS13-112112-UPVC RS13-2112-UPVC RS13-2122-UPVC RS13-3212-UPVC RS13-43-UPVC
CR33-12-UPVC CR33-34-UPVC CR33-1-UPVC CR33-114-UPVC CR33-112-UPVC CR33-2-UPVC CR33-212-UPVC
Page 8
P V C - U P R E S S U R E F I TT I N G SP L A I N
Y PIECE/45º TEE TY43
d
* PN10 RATED
1/2”3/4”1”
11/4”11/2”
2”21/2”*5”•*6”•*
L
16192226313844
Z1 Z2 E Wt (g)
778101214183443
293644546580101190224
27.533.542
50.561
74.591
364992149297513690
UNION UN83
d
* PN10 RATED
L Z1 Z2 G1 E Wt (g)
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”*
3”*4”*
14161922263138445161
3333333355
10101010121418181818
1/4"1"
11/4"11/2"
2"21/4"23/4"31/2"
4"5"
34425259727996119134163
304167901352063605807771150
• NON COMER PRODUCT
TY43-12-UPVC TY43-34-UPVC TY43-1-UPVC TY43-114-UPVC TY43-112-UPVC TY43-2-UPVC TY43-212-UPVC
UN83-12-UPVC UN83-34-UPVC UN83-1-UPVC UN83-114-UPVC UN83-112-UPVC UN83-2-UPVC UN83-212-UPVC UN83-3-UPVC UN83-4-UPVC
Page 9
P V C - U P R E S S U R E F I TT I N G SP L A I N
CAP CA73
d L H E Wt (g)
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”5”6”8”
141619222631384451617686119
22273136434957678095114126145
2328334150
60.57589106129161181258
7101626407312817831052092013173478
REDUCING BUSH RB93
d x d1 L L1 Z Wt (g)
STUB FLANGE ST23
d L Z S E E1 Wt (g)
1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”5”6”8"10"
1619222631384451617788119142
33333335577710
67788910111213141923
27334150617690108131163193248308
344150617390106125150187217274329
1014234868128160272361750115520923536
1/2" x 3/8"3/4” x 1/2"1” x 1/2"1” x 3/4"
11/4” x 3/4"11/4” x 1"
11/2” x 11/4"2” x 11/2"21/2” x 2"3” x 21/2"
4” x 3"
1619222226263138445161
1416161919222631384451
236374576710
341282215174172116246
CA73-12-UPVC CA73-34-UPVC CA73-1-UPVC CA73-114-UPVC CA73-112-UPVC CA73-2-UPVC CA73-212-UPVC CA73-3-UPVC CA73-4-UPVC CA73-5-UPVC CA73-6-UPVC CA73-8-UPVC
RB93-3412-UPVC RB93-134-UPVC RB93-11434-UPVC RB93-1141-UPVC RB93-112114-UPVC RB93-21-UPVC RB93-2114-UPVC RB93-2112-UPVC RB93-2122-UPVC RB93-3212-UPVC RB93-43-UPVC
ST23-12-UPVC ST23-34-UPVC ST23-1-UPVC ST23-114-UPVC ST23-112-UPVC ST23-2-UPVC ST23-212-UPVC ST23-3-UPVC ST23-4-UPVC ST23-5-UPVC ST23-6-UPVC ST23-8-UPVC
Page 10
P V C - U P R E S S U R E F I TT I N G SP L A I N
BLANK FLANGE BF00 - BS4504 NP10/16
SIZE E I F HOLES Bolt Dia Wt (g)
1/2”3/4”1”
11/4”11/2”
2”21/2"
3”4”6”
95105115142152165185200220283
657585100110125145160180240
4444444888
M12M12M12M16M16M16M16M16M16M20
751001372252803554886408251589
14141418181818181822
P V C - U P R E S S U R E F I T T I N G SP L A I N
FULL FACE FLANGE FF30 - BS10 TABLES D & E
d L Z I S E HOLES Bolt Dia Wt (g)
1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4"
161922263138445161
4.54.54.54.54.54.5678
6773838898115127146178
111214151618192022
95105115142152165185200220
444444448
M12M12M12M12M12M16M16M16M16
78105143220280380505685940
P V C - U P R E S S U R E F I TT I N G SP L A I N
BLANK FLANGE BF00 - BS4504 NP10/16
SIZE E I F HOLES Bolt Dia Wt (g)
1/2”3/4”1”
11/4”11/2”
2”21/2"
3”4”6”
95105115142152165185200220283
657585100110125145160180240
4444444888
M12M12M12M16M16M16M16M16M16M20
751001372252803554886408251589
14141418181818181822
FF30-12-UPVC FF30-34-UPVC FF30-1-UPVC FF30-114-UPVC FF30-112-UPVC FF30-2-UPVC FF30-212-UPVCFF30-3-UPVC FF30-4-UPVC
BF00-12-UPVC BF00-34-UPVC BF00-1-UPVC BF00-114-UPVC BF00-112-UPVC BF00-2-UPVC BF00-3-UPVC BF00-4-UPVC BF00-5-UPVC BF00-6-UPVC
Page 11
P V C - U P R E S S U R E F I T T I N G SP L A I N / T H R E A D E D ( B S P )
ADAPTOR AD32 - FEMALE PLAIN/MALE PLAIN/MALE THREADED
d x d1 x G d1 L L1 L2 H C Wt (g)
1/2" x 3/4" x 1/2"1/2" x 3/4" x 3/4"3/4" x 1" x 3/4"3/4" x 1" x 1"
1" x 11/4" x 1"1" x 11/4" x 11/4"11/4"x11/2"x11/4"11/4"x11/2"x11/2"11/2" x 2" x 11/2"
11/2" x 2" x 2"2" x 21/2" x 2"
2" x 21/2" x 21/2"21/2" x 3" x 21/2"
21/2" x 3" x 3"3" x 4" x 3"3" x 4" x 4"4" x 5" x 4"4" x 5" x 5"
3/4"3/4"1"1"
11/4"11/4"11/2"11/2"
2"2"
21/2"21/2"
3"3"4"4"5"5"
161619192222262631313838444453516161
191922222626313138384444515161616964
1516.316.319.119.121.421.421.421.425.725.730.230.233.333.339.339.343.6
464750535760
66.566.57478849199102113118120124
2730363642465555656575809595119115130140
1516272943526164110124152180260275578584426526
ADAPTOR AD42 - MALE PLAIN/FEMALE THREADED
d x G L L1 E Z C Wt (g)
1/2" x 1/2"1/2" x 3/4"3/4" x 1/2"3/4" x 3/4"3/4" x 1"1" x 3/4"1" x 1"
11/4" x 1"11/4" x 11/4"11/2" x 11/4"11/2" x 11/2"
11/2" x 2"2" x 11/2"
2" x 2"21/2" x 2"
21/2" x 21/2"21/2" x 3"3" x 21/2"
3" x 3"3" x 4"4" x 3"4" x 4"
16161919192222262631313138384444445151516161
1516.315
16.319.116.319.119.121.421.421.425.721.425.725.730.233.330.233.339.333.339.3
2834283442344242515158756075758910389103130103130
24242727273030363641414149485358586566657676
3036303646364646555560756575759010595105130130130
2328232843364655707575120130130150225310300330490460510
AD32-3-UPVC AD32-4-UPVC AD32-5-UPVC AD32-6-UPVC AD32-7-UPVC AD32-8-UPVC AD32-9-UPVC AD32-10-UPVC AD32-11-UPVC AD32-12-UPVC AD32-13-UPVC AD32-15-UPVC AD32-16-UPVCAD32-17-UPVC AD32-18-UPVCAD32-19-UPVC
AD42-1212-UPVC AD42-1234-UPVC AD42-3412-UPVC AD42-3434-UPVC AD42-341-UPVC AD42-134-UPVC AD42-11-UPVC AD42-1141-UPVC AD42-114114-UPVC AD42-112114-UPVC AD42-112112-UPVC AD42-1122-UPVC AD42-2112-UPVC AD42-22-UPVC AD42-2122-UPVC AD42-212212-UPVC AD42-2123-UPVC AD42-3212-UPVC AD42-33-UPVC AD42-34-UPVC AD42-43-UPVC AD42-44-UPVC
Page 12
P V C - U P R E S S U R E F I T T I N G SP L A I N / T H R E A D E D ( B S P )
TANK CONNECTOR TC93
D L1 L2 O Wt (g)
HOSE ADAPTOR HN64 - FEMALE BSP X MM HOSE TAIL
G x d
RANGE OF PP HOSE FITTINGS AVAILABLE SEE PAGE 308
H E Wt (g)
3/4" x 161" x 20
11/4" x 2511/2" x 30
2" x 4021/4" x 5023/4" x 60
54596368778084
34425259727996
23324968110145220
1/2”•3/4”•1”•
11/4”•11/2”•
2”•21/2”•
3”•4”•
7777103121128154164202230
42425570738294110140
384255657293106125154
41521081532163704717681421
• NON COMER PRODUCT
P V C - U P R E S S U R E F I TT I N G SP L A I N / TH R E A D E D ( B S P )
NIPPLE BN12*
D L2 L1 Wt (g)
3/8"•1/2”•3/4”•1”•
11/4”•11/2”•
2”•21/2”•
3”•4”•
13171620243032353943
42505663758888106128153
81425385280115197300560
* MACHINED FROM PIPE
• NON COMER PRODUCT
HN64-3416-UPVC HN64-120-UPVC HN64-11425-UPVC HN64-11230-UPVC HN64-240-UPVC HN64-21450-UPVC HN64-23460-UPVC
TC93-12-UPVC TC93-34-UPVC TC93-1-UPVC TC93-114-UPVC TC93-112-UPVC TC93-2-UPVC TC93-212-UPVC TC93-3-UPVC TC93-4-UPVC
BN12-38-UPVC BN12-12-UPVC BN12-34-UPVC BN12-1-UPVC BN12-114-UPVC BN12-112-UPVC BN12-2-UPVC BN12-212-UPVC BN12-3-UPVC BN12-4-UPVC
Page 13
P V C - U P R E S S U R E F I TT I N G ST H R E A D E D ( B S P )
NIPPLE BN11*
SIZE L H Wt (g)
1/4”•3/8"•1/2”•3/4”•1”•
11/4”•11/2”•
2”•21/2”•
3”•4”•
12131417191923303036
43505663758888106128153
111320305183119169243485
• NON COMER PRODUCT
* MACHINED FROM PIPE
BN11-14-UPVC BN11-38-UPVC BN11-12-UPVC BN11-34-UPVC BN11-1-UPVC BN11-114-UPVC BN11-112-UPVC BN11-2-UPVC BN11-212-UPVC BN11-3-UPVC BN11-4-UPVC
Page 14
P V C - U M A N UA L V A L V E S
STANDARD BALL VALVE BVD13 - DOUBLE UNION - PTFE SEAT - EPDM SEALS - PLAIN ENDS
G
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
L
14161922263138445161
Z
40404854627385115129149
H
68728698114135161203231271
A
505060688096116145166210
B
10101113182020252828
C
484854627587101123138160
E
3939475560688090100120
F
19192225303540455060
PN
15151515151515101010
Wt (g)
1401302002954407201190221035205790
P V C - U M A N U A L V A L V E S
INDUSTRIAL BALL VALVE BVI13 - DOUBLE UNION - PTFE SEAT - EDPM SEALS - PLAIN ENDS
d
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
L
14161922263138445161
Z
626274778793113116130150
H
9094112121139155189204232272
A
505060688096116145166210
B
10101113182020252828
C
484854627587101123138160
E
3939475560688090100120
F
19192225303540455060
PN
15151515151515101010
Wt (g)
1801702653705458851440230036556000
PV C-U MANUAL VALVES
STANDARD SPRING CHECK NON RETURN VALVE CVD13 - DOUBLE UNION - STAINLESS STEEL SPRING - EPDM SEALS - PLAIN ENDS
G
DETAILS FOR CHECK VALVE WITH PTFE COATED STAINLESS STEEL SPRING ARE AVAILABLE ON REQUEST
L Z H A Class Wt (g)
120110168246360595970174028104690
EEEEEEECCC
505060688096116145166210
768091102120140169214269290
48485358687893126139159
14161922263138445161
3/8"1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
BVD13-12-PVCBVD13-34-PVCBVD13-1-PVCBVD13-114-PVCBVD13-112-PVCBVD13-2-PVCBVD13-212-PVCBVD13-3-PVCBVD13-4-PVC
BVI13-38-PVCBVI13-12-PVCBVI13-34-PVCBVI13-1-PVCBVI13-114-PVCBVI13-112-PVCBVI13-2-PVCBVI13-212-PVCBVI13-3-PVCBVI13-4-PVC
CVD13-12-PVCCVD13-34-PVCCVD13-1-PVCCVD13-114-PVCCVD13-112-PVCCVD13-2-PVCCVD13-212-PVCCVD13-3-PVCCVD13-4-PVC