quarter 1, module 1, week 2 marian jean sortez-yapac(adm) module on maintain electric and hydraulic...
TRANSCRIPT
TLE
ELECTRICAL INSTALLATION AND MAINTENANCE
Quarter 1, Module 1, Week 2
MARIAN JEAN SORTEZ-YAPAC
(SUPPORT MATERIAL FOR INDEPENDENT LEARNING ENGAGEMENT)
A Joint Project of
SCHOOLS DIVISION OF DIPOLOG CITY
and the
DIPOLOG CITY GOVERNMENT
9
TLE – Grade 9 Quarter 1 – Module 1: Electrical Installation and Maintenance First Edition, 2020 Republic Act 8293, section 176 states that: No copyright shall subsist in any work of the Government of the Philippines. However, prior approval of the government agency or office wherein the work is created shall be necessary for exploitation of such work for profit. Such agency or office may, among other things, impose as a condition the payment of royalties. Borrowed materials (i.e., songs, stories, poems, pictures, photos, brand names, trademarks, etc.) included in this module are owned by their respective copyright holders. Every effort has been exerted to locate and seek permission to use these materials from their respective copyright owners. The publisher and authors do not represent nor claim ownership over them.
Printed in the Philippines by ________________________ Department of Education – Bureau of Learning Resources (DepEd-BLR)
Office Address: ____________________________________________
____________________________________________
Telefax: ____________________________________________
E-mail Address: ____________________________________________
Development Team of the Module
Writer: Marian Jean Sortez-Yapac
Editor:
Reviewers: Rosel P. Patangan, Marjhon F. Yapac, Jomalyn J. Suizo,
Rose Gee F. Sebastian, Victoria I. Monteza, Lloyd Ivonn Mark Ordinaria
Illustrator:
Layout Artist: Leo Martinno O. Alejo
Management Team: Dr. Virgilio P. Batan,Jr -Schools Division Superintendent
Dr. Jay S. Montealto -Asst. Schools Division Superintendent
Amelinda D. Montero -Chief, CID
Nur N. Hussien - Chief, SGOD
Ronillo S. Yarag -EPSpvr-LRMS
Leo Martinno O. Alejo -PDO II - LRMS
Department of Education • Republic of the Philippines
9
Technology and
Livelihood Education
Quarter 1 – Module 1- Week 2: Maintain Electric and Hydraulic Tools
Code: TLE_IAEI9-12ET-If-j-2
2
Introductory Message
For the facilitator:
Welcome to the Technology and Livelihood Education - Industrial Arts
(Electrical Installation and Maintenance) Grade 9 Alternative Delivery Mode
(ADM) Module on Maintain Electric and Hydraulic Tools.
This module was collaboratively designed, developed and reviewed by educators both
from public and private institutions to assist you, the teacher or facilitator in helping
the learners meet the standards set by the K to 12 Curriculum while overcoming
their personal, social, and economic constraints in schooling.
This learning resource hopes to engage the learners into guided and independent
learning activities at their own pace and time. Furthermore, this also aims to help
learners acquire the needed 21st century skills while taking into consideration their
needs and circumstances.
In addition to the material in the main text, you will also see this box in the body of
the module:
As a facilitator you are expected to orient the learners on how to use this module.
You also need to keep track of the learners' progress while allowing them to manage
their own learning. Furthermore, you are expected to encourage and assist the
learners as they do the tasks included in the module.
Notes to the Teacher
This contains helpful tips or strategies that
will help you in guiding the learners.
3
For the learner:
Welcome to the Technical and Livelihood Education – Industrial Arts (Electrical
Installation and Maintenance) Alternative Delivery Mode (ADM). Module on Maintain
Electric and Hydraulic Tools!
The hand is one of the most symbolized part of the human body. It is often used to
depict skill, action, and purpose. Through our hands we may learn, create, and accomplish. Hence, the hand in this learning resource signifies that you as a learner
is capable and empowered to successfully achieve the relevant competencies and skills at your own pace and time. Your academic success lies in your own hands!
This module was designed to provide you with fun and meaningful opportunities for
guided and independent learning at your own pace and time. You will be enabled to
process the contents of the learning resource while being an active learner.
This module has the following parts and corresponding icons:
What I Need to Know
This will give you an idea of the skills or
competencies you are expected to learn in the
module.
What I Know
This part includes an activity that aims to
check what you already know about the
lesson to take. If you get all the answers
correct (100%), you may decide to skip this
module.
What’s In
This is a brief drill or review to help you link
the current lesson with the previous one.
What’s New
In this portion, the new lesson will be
introduced to you in various ways such as a
story, a song, a poem, a problem opener, an
activity or a situation.
What is It
This section provides a brief discussion of the
lesson. This aims to help you discover and
understand new concepts and skills.
What’s More
This comprises activities for independent
practice to solidify your understanding and
skills of the topic. You may check the
answers to the exercises using the Answer
Key at the end of the module.
What I Have Learned
This includes questions or blank
sentence/paragraph to be filled in to process
what you learned from the lesson.
What I Can Do
This section provides an activity which will
help you transfer your new knowledge or skill
into real life situations or concerns.
4
Assessment
This is a task which aims to evaluate your
level of mastery in achieving the learning
competency.
Additional Activities
In this portion, another activity will be given
to you to enrich your knowledge or skill of the
lesson learned. This also tends retention of
learned concepts.
Answer Key
This contains answers to all activities in the
module.
At the end of this module you will also find:
The following are some reminders in using this module:
1. Use the module with care. Do not put unnecessary mark/s on any part of the
module. Use a separate sheet of paper in answering the exercises.
2. Don’t forget to answer What I Know before moving on to the other activities
included in the module.
3. Read the instruction carefully before doing each task.
4. Observe honesty and integrity in doing the tasks and checking your answers.
5. Finish the task at hand before proceeding to the next.
6. Return this module to your teacher/facilitator once you are through with it.
If you encounter any difficulty in answering the tasks in this module, do not
hesitate to consult your teacher or facilitator. Always bear in mind that you are
not alone.
We hope that through this material, you will experience meaningful learning and
gain deep understanding of the relevant competencies. You can do it!
● Demonstrate what you learned by doing the additional activities
References This is a list of all sources used in developing
this module.
5
What I Need to Know
MODULE TITLE: Maintain Electric and Hydraulic Tools
MODULE DESCRIPTION:
Welcome to the world of Electrical Installation and Maintenance!
This module contains the “know” and “do” units in preparing electrical power
and hydraulic tools.
It covers the knowledge, skills and attitude in preparing electrical power tools
needed before starting work. Tools are inspected and damaged tool, if any, must be
reported to the teacher and serviced. Proper checking must also be done before
commencing work so that lubrications and auxiliary parts are per enterprise
specifications. Proper storing must also be practiced.
This module consists of three (3) learning outcomes (LOs) that contain
learning activities for both knowledge and skills supported with information sheets,
job/operation sheets and self-check. Before attempting to perform the manual
exercises, see to it that you have already read and understood the
information/operation sheet and answered correctly the self-check provided in every
Learning Activities.
After going through this module, you are expected to:
1. Check the conditions of electric and hydraulic tools
2. Lubricate electric tools in line with manufacturer’s specification
3. Replace auxiliary part of electric and hydraulic tools according to
manufacturer’s specifications; and
4. Store electric and hydraulic tools
CODE: TLE_IAEI9-12ET-If-j-2
6
What I Know
Pre-Assessment
Name _________________________ Date___________________ Year/Sec: ____________
Matching Type: Match the picture of electrical signs and symbols in Column B and its meaning in Column A. Write the letters on the space
provided by the number.
COLUMN A COLUMN B
______1. It indicates a potentially hazardous
situation which if not avoided, may result in property damage.
______2. It indicates a potentially hazardous
situation which, if not avoided, could result serious injury or death.
______3. It indicates an imminently hazardous
situation which if not avoided, may
result in serious injury or death.
______4. Read and Understand Instruction Manual.
______5. Eye Wear Protection
A
B
C
E
D
7
Lesson
1
Maintain Electric and Hydraulic Tools
Maintenance is an action an item in or to restore it to its functional condition.
Regular maintenance and servicing of power tools and electric tools and electric tools
will help to ensure that they operate with optimum efficiency at all times.
The first thing to do in any preventive maintenance system is to use your eyes,
nose, ears, experience, and judgement. Follow your instinct or your keen observation
on an equipment when doing preventive maintenance.
PLANNED MAINTENANCE
1. Preventive maintenance is performed in order to ensure that the tools are
operating properly and efficiently.
2. Corrective maintenance is performed in order to correct a failure.
3. Emergency maintenance is necessary to put the item at hold immediately to
avoid serious consequences such as the loss of production, extensive damage
of assets, and for safety reasons.
4. LUBRICATION the following features contribute to safety and economic
lubricating machine tools:
1. Plates on machines clearly show the grades of lubricant, quantities and
intervals are required. The machine name, type, and model should be
visible.
2. Maintain the proper level of lubrication reservoirs.
3. Suitable method of lubrication should be followed to minimize or
prevent metal- to-metal contact at all times.
4. Sufficient lubricant capacity is needed to prevent overheating and
thermal distortion of machine tool structures.
5. Adequate sealing should be properly observed. Install provision for
removal of contaminant collected by the lubricant (e.g., filters)
Reference: Information Sheet 2.3 Page31-32 INDUSTRIAL ARTS: ELECTRICITY
9(PREPARING ELECTRIC AND HYDRAULIC TOOLS) Learner’s Material
https://www.slideshare.net/maric
risbrandes/electrical-and-hydraulic-tools-
maintenance-procedure
8
What’s In
Before you proceed with the new lesson, take a few minutes and write down some
of the information that you’ve learned from the previous lessons. Do this in a sheet of paper for at least 100 words.
What’s New
Do the following activity.
True or False:
Direction: Write true if the statement is correct and write false if the statement is
incorrect.
_____1. Ensure that the heat gun, guard and attachments (Including handle) are
secure and correctly fitted.
_____2. Keep fingers, hands and power cords clear of the tip the heat gun (heat gun
tube or nozzle).
_____3. Examine the power cord, extension lead, plugs, sockets and power outlet
for possible damage.
_____4. Disconnect the drill from the electrical supply when installing the bits.
_____5. Clamp stock so it will not move during the drilling operation.
_____6. Before drilling, turn the drill on to see if the bit is centered and at place.
_____7. Never grind with the portable disc grinder in an area with flammable
materials or combustible gases.
_____8. Never lay the portable disc grinder down until the disk stopped rotating.
_____9. Never disconnect the hose when it is under pressure.
_____10. Keep the electrical cords and extension cords out of the way work when
grinding.
9
Lesson Information 3.1
Learning Objectives: After Reading this module you must be able to explain how to handle safely
electrical power and hydraulic tools.
Safe Handling and Operating Principle of Power Tools Power tools must be fitted with guards and safety switches; they are extremely
hazardous when used improperly.
To prevent hazards associated with the use of power tools, workers should observe
the following general precautions:
1. Never carry a tool by the cord or hose.
2. Never yank the cord or the hose to disconnect it from the receptacle.
3. Keep cords and hoses away from heat, oil, and sharp edges.
4. Disconnect tools when not using them, before servicing and cleaning them,
and when changing accessories such as blades, bits, and cutters.
5. Keep all people not involved with the work at a safe distance from the work
area.
7. Secure work with clamps or a vise, freeing both and to operate the tool.
8. Avoid accidental starting.
9. Do not hold fingers on the switch button while carrying a plugged-in tool.
10. Maintain tools with care; keep them sharp and clean for best performance.
11. Follow instructions in the user’s manual for lubricating and changing
accessories.
12. Be sure to keep good footing and maintain good balance when operating
power tools.
13. Wear proper apparel for the task. Loose clothing, ties, or jewelry can
become caught in moving parts.
14. Remove all damaged portable electric tools from use and tag them:
“Do Not Use.”
Safe Handling and Operating Principle of Hydraulic Tools
15. Read and understand the entire owner's manual before attempting
assembly or operation.
16. Read and understand the warnings posted on the machine and in this
manual. Failure to all of these warnings may cause serious injury.
17. Replace the warning labels if they become obscured or removed.
What is It
10
18. Hydraulic Tools are designed and intended only if you are not familiar
with the proper and safe operation of a pipe bender, do not use until
proper training and knowledge have been obtained.
19. Before operating Hydraulic Tools (Pipe Bender), remove tie, rings, watches
and other jewelry, and roll sleeves up past the elbows. Remove all loose
clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
20. Do not operate Hydraulic tools while tired or under the influence of drugs,
alcohol or any medication.
21. Check damaged parts. Before further use of the machine, a guard or ot
her part that is damaged should be carefully checked to determine that it
will operate properly and perform it is intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect it is operation. A guard
or other part that is damaged should be properly repaired or replaced.
22. Provide for adequate space surrounding work area and non-glare,
overhead lighting.
23. Keep the floor around the machine clean and free of scrap material, oil
and grease.
24. Keep visitors a safe distance from the work area. Keep children away.
25. Give your work undivided attention. Looking around, carrying on a
conversation and “horse-play” are careless acts that can result in serious
injury.
26. Maintain a balanced stance and do not overreach or us excessive force to
perform any machine operation.
27. Use the right tool. Do not force a tool or attachment to do a job for which
it was not designed. The right tool will do the job better and safer.
28. Use recommended accessories; improper accessories maybe hazardous.
29. Maintain tools with care and clean for the best and safest performance.
Follow instructions for lubricating and changing accessories.
Note:
Familiarize yourself with the following safety notices found in manuals:
This means that if precautions are not heeded or observed, it may result in minor
injury and/or possible machine damage.
11
Always Use Proper PPE
L.O. 4. Operating Procedure of Electrical Power and Hydraulic Tools
• Explain the Operating Principles of Electrical Power Tools
• Practice how to operate electrical power tools
Lesson Information 4.1
Operating procedure of Electrical Power and Hydraulic Tools
Learning Objectives: After Reading this discussion you must be able to:
know the operating procedures of electrical power and;
hydraulic tools that is commonly used during electrical installation.
Operating Angle Grinder Performance Objective: Given necessary tools and materials, you must be
able to operate Angle Grinder.
Operating Precaution:
1. Examine the power cord, extension lead, plugs, sockets and power outlet for possible damage.
2. Ensure the grinding disc for damage, don not use damage grinding disc 3. Ensure that the grinding disc, guard and attachments (Including handle) are
secure and correctly fitted. 4. Keep fingers, hands and power cords clear of the grinding disc.
Safety glasses must be
worn at all times in work areas.
Appropriate footwear with substantial uppers
must be worn.
Rings and jewelry must
not be worn.
Long and loose hair must be contained.
Close fitting/protective
clothing must be worn.
Hearing protection
must be worn when using this machine.
12
Operating Procedure:
Grinding Works 1. Attach Grinding Disc to angle grinder
2. Make sure the Disc is fully fitted with the inner flange. 3. Lock the outer flange using wrench, make sure the Disc is properly installed and
lock tightly.
4. Mark accurately the area for cutting/grinding.
5. Hold tightly the handle of the grinder and turn the power switch ON.
6.Drop the grinding disc/wheel through the marked area. (Caution: Hold tightly
the grinder with both hands and put your goggles and dust mask) 7. Apply an amount of pressure while cutting/grinding. Make sure you hold the
grinder with a firm grip, as there is a tendency for the grinder to want to jump out of your hands when it hits the area.
http://www.academia.edu
http://www.academia.edu
http://www.academia.edu
13
8. After grinding, remove the disc from the cut area and Turn-Off the grinder
then remove the power cord, 9. Clean the grinder before storing.
Operating Hand Drill
Performance Objective: Given necessary tools and materials, you must be able to operate Hand Drill.
Operating Precaution:
1. Examine the power cord, extension lead, plugs, sockets and power outlet for possible damage.
2. Keep fingers, hands and power cords clear of the rotating part of the hand drill and drill bit
www.academia.edu
Operating Procedure:
Drilling Works
1. Choose the size and location of the hole. (See Project 1.1-4b)
2. Base on the given project, measure and mark the location with Pencil.
3. Use center punch and make a small hole on the center of the marked area
4. Identify the correct size of drill bit to be used (the size depends on the size of screw being used)
5. Secure the drill bit in the chuck. (Leave the hand drill unplug) open an empty chuck by twisting the outer barrel with your hand.
6. Place the bit in between the three grips and tighten the chuck. (Use chuck key
to tighten)
http://www.academia.edu
14
7. Drill the hole, (Always wear proper PPE) Place the point of the bit over the
marked area with small hole.
8. Hold the hand drill perpendicular to the surface and slowly squeeze the trigger button or switch gently. (Hold firmly so it doesn’t shift once it
starts turning
9. Check the depth of your hole with the screw that is going into it. (Drill deeper
if necessary)
10. Unplug the drill, and remove the bit from the chuck
11. Clean hand drill before storing.
Marked Area for drilling
http://www.academia.edu
http://www.academia.edu http://www.academia.edu
http://www.academia.edu
15
Operating Heat Gun
Performance Objective:
Given necessary tools and materials, you must be able to operate Heat Gun.
Operating Precaution:
1. Examine the power cord, extension lead, plugs, sockets and power outlet for
possible damage.
2. Ensure that the heat gun, guard and attachments (Including handle) are secure and correctly fitted.
3. Keep fingers, hands and power cords clear of the tip the heat gun (heat gun tube or nozzle)
Operating Procedure
Bending Works
1. Prepare the material for heating 2. Check the nozzle to be used for heating base on the area for heating
3. Hold and Turn On (Plug the power) the switch by squeezing the switch button (Most Heat Gun has variable speed and heat) squeeze to full speed and heat if the
material needs more heat and medium speed and heat if the material needs small
amount of heat. 4. Point the nozzle on the area or material to be heated
Note; excessive heat may damage the material heated and the distance of the heat gun nozzle and area to be heated affects the amount of heat that hits
material or area. 5. Turn Off and let the nozzle cool down.
6. Clean heat gun before storing.
Operating Hydraulic Bender
Performance Objective: Given necessary tools and materials, you must be able to
operate Hydraulic Bender.
Operating Precaution:
1. Check hydraulic pump for any defects before using. 2. Always observe operating precautions of the bender.
http://www.academia.edu
16
Operating Procedure:
1. Identify the size of pipe for bending to match the size of
die to be used. 2. Raise the handle and the
upper wing plate.
3. Select the suitable bending die
for the pipe to be bent and slip it on the end of cylinder
ram. 4. Select the positions of swaging
blocks for the pipe. Note: For shorter pipes, position the
swaging blocks closer
together to account for the pipe shortening during the
bending process 5. Turn the swaging blocks to the
notch that best fits the diameter of the pipe to be
bent. (Lubricating the swaging blocks will promote
ease of movement)
6. Place the pipe for bending 7. Lower the upper plate
8. Close the release valve (Turn clockwise)
9. Pump the handle to bend the pipe
10. When the pipe bend has been made, release the pressure by
opening the release valve (Turn counter clockwise) the ram will automatically
retreat. 11. Clean hydraulic bender before storing.
Lesson Information 5.1
Maintaining Electrical Power and Hydraulic Tools
Learning Objectives: After Reading this discussion you must be able to maintain
and store properly the electrical power and hydraulic tools that is commonly used during electrical installation. You must also be able to report the damaged
electrical
and hydraulic tools.
Maintenance:
17
1. Maintenance is an action carried out to retain electrical power and hydraulic tools
in an acceptable condition, 2. The principal objectives of maintenance can be clearly defined as follows:
• To extend the useful life of electrical power and hydraulic tools • To assure the optimum availability of electrical power and hydraulic tools
• To ensure operational readiness of electrical power and hydraulic tools • To ensure safety of personnel using electrical power and hydraulic tools
Types of Maintenance 1. Planned Maintenance – Work activities are performed as scheduled or expected
a. Preventive Maintenance –Maintenance performed to prevent or find
failure before they develop into breakdown b. Predictive Maintenance – Maintenance performed at a predetermined
periods when the maintenance activity is most cost effective and before the equipment fails.
2. Unplanned Maintenance – Maintenance performed unexpectedly a. Emergency – Maintenance performed to put the item on hand
IMMEDIATELY to avoid serious consequence
Maintenance Schedule
Maintenance Schedule – Is a list allocating specific maintenance of equipment
and tools to a specific period. Sample Maintenance Schedule
MAINTENANCE SCHEDULE
18
What’s More
A. Direction. On your answer sheet, illustrate the following electrical materials.
1. Circuit breaker
2. Utility box
3. Philip head screw driver
4. PVC clamp
5. Male plug
6. EMT bender
7. Locknut
8. Insulated staple wire
9. Stranded wire
10. Long nose plier
B. Direction. Identify the tools being describe. Write your answer on your answer
sheet.
1. It is used to drive and loosen screws.
2. It is a tool used to bend electrical metal tubing.
3. It is needed to make holes in building structure for passage of wires and conduit
in both new and old installation, indoor or outdoor wiring.
4. It is used to pull wires into the conduit or raceway.
5. It is also known as a side or disc grinder, is a hand held power tool used for
cutting, grinding and polishing.
6. These are some electrical materials which are commonly used to fit wiring
devices during wiring installation.
19
7.It is a hand-operated tool for holding and gripping small articles or for bending
and cutting wire.
8. It is composed of two or more electric conductors insulated from one another.
9. These are electrical protective devices which are used to interrupt the flow of
current when short circuit or over current occurs.
10. It can used to bend electrical PVC pipe.
What I Have Learned
Direction: Identify the parts of a portable electric drill. Write the correct answer on
your answer sheet.
___________________1.
___________________2.
___________________3.
___________________4.
___________________5.
___________________6.
___________________7.
___________________8.
20
What I Can Do
PREPARING REQUISITION SLIP FORM
Direction: Using the given format below, make a requisition for your electrical
project which is wiring up a small room with a lamp controlled by a switch. The activity will involve embedding a rigid conduit on the concrete wall and wooden
ceiling.
REQUISITION
Slip Form Name: ________________
Project: ____________________ Location: ___________________
Classification: _______________ Purpose: ____________________
21
________________ _________________
Requisitioner Teacher
Assessment
Direction: Read each question carefully and choose the letter of the correct
answer. Write your answer in a separate paper.
1. What personal protective equipment should be worn when operating the
portable disc grinder? a. Safety glasses
b. Safety glasses and hearing protection c. Safety glasses, hearing protection and gloves d. Safety glasses, hearing protection, gloves and respirator.
2. When operating the portable disc grinder, the grinding disk should be positioned so that the sparks and grit are thrown.
a. away from the operator. b. away from the operator and others in the work area.
c. up to avoid hitting others. d. down to avoid hitting others.
3. Grinding with the portable disc grinder should not be done in an area
which______________. a. is enclosed
b. is freshly painted c. has windows.
d. contains flammables or combustible gases. 4. The grinding disc should be replaced when worn out and reduces___________ of its original diameter.
a. ¼ b. ½ c. 5/8 d. 3/4 5. Hands and arms should be protected by wearing ____________ when using
the portable disc grinder. a. gloves c. long sleeved leather jacket
b. long sleeved shirt d. long sleeved leather gloves. 6. What can the operator expect to happen when the wire brush attachment is used on the portable disc grinder?
a. The grinder may be jumped out or be thrown out. b. The grinder moves back and forth.
c. The grinder stays steady on the material being bushed. d. The grinder performs well.
7. When the portable disc grinder is laid down, it should be positioned _________.
https://studylib.net/doc/18
397466/preparing-electric-
and-hydraulic-tools
22
a. with the disc down. b. on its left side.
c. on its right side. d. on the tool rest with the grinding disc facing up.
8. What is the minimum size of the electrical extension cord used with most portable disc grinders?
a. #14 b. #12 c. #10 d. #8 9. Why is it necessary to tighten the disk lock nut snuggly only when the disc is replaced on the portable disc grinder?
a. The threads will be stripped on the spindle. b. The disc may be too difficult to remove next time.
c. The natural rotation of the disc and spindle will cause the threads to tighten.
d. The loose threads are allowed to hold some of the vibration created by the portable disc grinder.
10. What can the operator do to avoid hand and finger fatigue when using
the portable disc grinder for extended periods of time? a. Eat lots of carbohydrates. c. Wear long sleeved gloves.
b. Drink plenty of water. d. Use the switch lock.
Additional Activities
23
Answer Key
What I Know
1.A
2.B
3.C
4.D
5.A
What’s In
What I Have Learned
1.Chain
2.True
3.Lazy daisy
4.French knot 5.Straight
6.Chain stitch
7.Cross stitch
8.Cross stitch
Assessment
1.B
2.A
3.D
4.D
5.C 6.A
7.A
8.D
9.C
10.A
What’s New
A. 1.Running stitch
2.Lazy daisy
3.Feather stitch
4.Satin stitch
5.Chain stitch B.
1.Running stitch
2.Chain stitch
3.Split
4.Lazy daisy
5.Bullion 6.Feather
7.Herringbone
8. French Knot
What's More
1.Running 2.Lazy daisy
3.Fish Bone
4.Looped
5.French Knot
24
References
Adapted to the K-12 Basic Education Curriculum Technology and
Livelihood Education, Learning Module Handicraft Production
Grade7/8
https://en.wikipedia.org/wiki/Embroidery_stitch
https://www.pinterest.ph/pin/385831893061128836/
https://www.youtube.com/watch?v=go89e8xpVYs
https://www.vskills.in/practice/embroidery-stitch-questions
https://www.embroidery.rocksea.org/reference/picture-dictionary/
https://sg.inflibnet.ac.in/bitstream/10603/51095/10/10_chapter%2
01.pdf
https://www.fibre2fashion.com/industry-article/4135/history-of-
embroidery
https://www.google.com/search?sxsrf=ALeKk03b1uVg_E3UyFnGT5rd
T7dKSlernA:1595804049996&source=univ&tbm=isch&q=embroidery+
stitches+picture&sa=X&ved=2ahUKEwi0vZ-
sgezqAhWlyIsBHSLFBaMQsAR6BAgFEAE&biw=1242&bih=597#imgrc
=3ZhrdFPObTWJFM
For inquiries or feedback, please write or call: Department of Education – (Bureau/Office)
(Office Address)
Telefax:
Email Address: